GOT3126T-842-C All-in-One 12.1 XGA TFT Fanless Compact-Size PANEL PC 使用手册 RoHS
责任声明 本使用手册受著作权保护 所撰写之内容均为艾讯科技所拥有 本使用手册所提及之产品规格或相关信息 本公司保留修改及删除 之权利 本使用手册已经经过内部技术人员确认信息的准确 但艾讯科技不 会承担手册中任何错误及省略的责任 本使用手册所提及之产品规格或相关信息有任何修改 删除或变更 时 恕不另行通知 未事先经由本公司书面允许 不得以任何形式复制 修改 转载 传送或出版本使用手册内容 为了协助您使用艾讯科技主机板 请仔细阅读 使用手册 产品相关信息 请至艾讯科技官方网站查询 www.axiomtek.com.cn 版权 2016年 艾讯科技(深圳)有限公司 版权所有 本使用手册所提及之商标与名称 均属其合法注册之公司所有 I
安装 拆卸前的注意须知 主机板是由许多精密的集成电路及其他元件所构成 这些集成电路很容易因静电影响 而损坏 所以在安装前请先详阅此使用手册并做好下列准备 安装前请确认所使用的机壳尺寸与主机板相符 安装前请勿任意撕毁主机板上的序号及代理商保固贴纸等 否则会影响到产品保 固期限的认定标准 要安装或移除主机板以及其他硬设备之前请务必先关闭电源 并且将电源线自插 座中拔除 安装其他硬设备至主机板内的插座时 请确认接头和插座已紧密结合 拿取主机板时请尽量不要触碰金属接线部份以避免线路发生短路 拿取主机板 中央处理器(CPU)或存储器模块时 最好戴上防静电手环 若无防静 电手环 请确保双手干燥 并先碰触金属物以消除静电 主机板在未安装之前 请先置放在防静电垫或出货时所使用的防静电袋内 当您要拔除系统电源插座上的插头时 请确认电源是关闭的 在开启电源前请确定电源的电压值是设定在所处区域的电压标准值 在开启电源前请确定所有硬设备的排线及电源线都已正确且牢固地连接 请勿让螺丝接触到主机板上的线路或零件 避免造成主机板因短路而产生损坏或 故障 请确定没有遗留螺丝或金属制品在主机板上或计算机机壳内 请勿将主机置放在不平稳处以免计算机因突然倾倒而造成的突然关机 请勿将计算机主机放置在超过产品规范的温度环境中 在尚未组装完成时开启电源可能会造成主机板 其他设备或零件及您自己本 身的伤害 要移除连接于各插座上的连接线时 请先移除设备端的接头 再移除连接至主机 II
板端的接头 移除连接线时 请直接拔出 切勿左右摇晃接头 以免造成接头内的线路短路 如果您对执行安装不熟悉 或使用本产品发生任何技术性问题时 请洽询专业的 技术人员 BAT电池 此电池提供计算机系统于关闭电源后仍能记忆 CMOS 资料(例如 日期及 BIOS 所需 的电力 当此电池的电力不足时 会造成 CMOS 的资料错误或遗失 因此当电池电力不 足时必须更换 您也可以利用拔除电池来清除CMOS资料 1. 请先关闭计算机 并拔除电源线 2. 小心地将电池从电池座中取出 等候约一分钟 (或是使用如螺丝起子之类的金属 物碰触电池座的正负极 造成其短路约五秒钟) 3. 再将电池装回 4. 接上电源线并重新开机 注意事项 更换电池前 请务必关闭计算机的电源并拔除电源线 更换电池时请更换相同型号的电池 不正确的型号可能引起爆炸的危险 若无法自行更换电池或不确定电池型号时 请联络购买店家或代理商 安装电池时 请注意电池上的正(+)负(-)极(正极须向上) 更换下来的旧电池须依当地法规处理 III
目录 责任声明 版权 安装 拆卸前的注意须知 BAT 电池 第一章节 1.1 1.2 1.3 1.4 1.5 产品介绍 1 General Description 1 Specifications 2 Dimensions and Outlines 4 I/O Outlets 5 Packing List 5 第二章节 硬件和安装 6 2.1 Open back cover 7 2.2 CF card Installation 7 2.3 Serial Ports Interface 8 2.3.1 COM1 & COM2 Connector 9 2.4 Ethernet 10 2.5 Mountings: Panel / Wall / VESA 10 2.5.1 VESA-ARM/Wall-Mount 10 2.5.2 Panel-mount Kit Assembly 11 2.6 2.7 2.8 2.9 HDD Installation 11 DRAM Installation 13 Wireless LAN Card Installation 14 Power 15 第三章节 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 17 Starting 17 Navigation Keys 17 Main Menu 18 Advanced Menu 19 Chipset Menu 33 Security Menu 35 Boot Menu 36 Save & Exit Menu 37 IV
第一章节 产品介绍 This chapter contains general information and detailed specifications of the GOT3126T-842-C. Chapter 1 includes the following sections: General Description Specification Dimensions I/O Outlets Package List 1.1 General Description The GOT3126T-842-C adopts a 12.1-inch XGA TFT LCD with 350-nit brightness and an Intel Celeron quad core processor J1900 2.42 GHz to provide excellent computing performance and thermal resistance. This fanless platform is especially designed for operating under heavy-duty environment including steel refinery, oil pipe, ship, machine maker operating systems and many more. Having below abilities makes GOT3126T-842-C surely a most robust and cost-effective solution. Wide Operating Temperature Range GOT3126T-842-C features a technology of wide operating temperature range which allows it to work between-20 C to +55 C. It incorporates compact ID and fanless cooling system with a low power Intel Celeron processor J1900 2.42 GHz, making the platform a power-efficient solution. Reliable and Stable Design The GOT3126T-842-C adopts a fan-less cooling system and a CompactFlash card, which makes it especially suitable for vibration-heavy environments, best for the transportation, ship, and industrial machinery markets. For high capacity storage requirement, GOT3126T-842-C can work under 1.3G (10 ~ 500Hz, random for 2.5 HDD) in operation mode with apatent of anti-vibration design. The patent improves the system reliability and sustainability. 产品介绍 1
WLAN Antenna Supported (optional) GOT3126T-842-C has a PCI Express Mini Card slot for optional add-ons such as wireless LAN card for 802.11 b/g connections& 3G/GPRS application, graphics-enhanced video card, universal analog TV/FM tuner/av capture card, and more. It also provides an optional fixed rotational WLAN antenna for wireless network connection. More Features GOT3126T-842-C utilizes one 204-pinDDR3 SODIMM system memory max. Up to 8GB, one SATA HDD and one Compact FlashTM slot. It provides over-current protection-fuse and a full set of I/O including 2 RS-232, 2 RS-232/422/485, 1 USB 3.0, 3 USB2.0, two audio (line-out/mic in), 2 Gigabit Ethernet, 1 HDMI and 1 VGA. Additionally, this slim unit supports panel mount, wall mount( optional), VESA mount (optional)and desktop stand (optional). 1.2 Specifications Main CPU Board CPU Intel Celeron System Chipset Soc System J1900 2.42GHz processor onboard integrated Memory One204-pin Maximum DDR3 SO-DIMM socket memory up to 8GB BIOS America Megatrends BIOS I/O System Standard I/O Two RS-232 and two RS-232/422/485 One USB 3.0 & Three USB 2.0 Ethernet Two RTL81111b Gigabit Ethernet Audio One Line-out & one Mic in Graphics One HDMI & one VGA Expansion One 产品介绍 Mini PCIe card 2
Storage One slot for CF card One SATA Power connector Phoenix power connector System Specification 12.1 XGA(1024x768) LCD with LED backlight 5 wired resistive Touch Fanless Heat Dispensing Design IP65 aluminum front bezel Disk drive housing: One Net 2.5 SATA drive Weight 2.8 Kgs (6.78 lb) Dimension (Main Body Size) 311.5mm x 56.9mm x 250mm Operation temperature -20 Relative 20% Power to 55 Humidity to 90% @ 40, Non-Condensing input DC power 12V (phoenix type) Note: All specifications and images are subject to change without notice. Note: If the operation temperature is higher than 40, the wide temperature HDD is recommended to be used on the device. Note: If the operation temperature is higher than 45, the wide temperature CF is recommended to be used on the device. 产品介绍 3
1.3 Dimensions and Outlines The following diagrams show the dimensions and outlines of GOT3126T-842-C. 产品介绍 4
1.4 I/O Outlets Please refer to the following illustration for I/O locations of the GOT3126T-842-C. No Function No Function 1 POWER SWITCH 7 COM 2 (RS-232/422/485) 2 Power Input connector (phoenix) 8 HDMI 3 COM 3 9 VGA 4 COM 4 10 USB 3.0 5 PS/2 KB &MOUSE 11 LAN 6 COM 1 (RS-232/422/485) 12 USB 2.0 1.5 Packing List When you receive the GOT3126T-842-C, the bundled package should contain the following items: GOT3126T-842-C Driver CD x1 Phoenix Panel unit x 1 connector x 1 mount kit x 6 Screws for HDD x 4 If you can not find the package or any items are missing, please contact Axiomtek distributors immediately. 产品介绍 5
第二章节 硬件和安装 The GOT326T-842 provides rich I/O ports and flexible expansions for you to meet different demand, for example CF card. The chapter will show you how to install the hardware. It includes: Open back cover Flash Card Compact Serial Port Ethernet Mounting Hard Method disk DRAM Wireless LAN Card Power 硬件和安装 6
2.1 Open back cover This section tells users how to open back cover. Please follow the steps below. Step 1 Unscrew ten screws on the back cover. Please refer the photo below. Step 2 Remove the back cover. 2.2 CF card Installation The GOT3126T-842-C provides one CF slot for users to install Compact Flash card. Please refer to the following instructions for installation: Step 1 Unscrew as crew on the cover of CF card slot on leftside of GOT. Step 2 Stick mylar on the CF card. 硬件和安装 7
Step 3 Insert the card into the socket. Step 4 Close the cover of CF card slot and fix it. Installation completes. 2.3 Serial Ports Interface The GOT3126T-842-C has four serial ports. COM1/2 are RS-232/422/485, while COM3/4 are RS-232. The following table shows you the pin assignments of this connector: COM1 COM2 硬件和安装 8
2.3.1 COM1 & COM2 Connector The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with +5V level power capability on DCD and +12V level on RI by setting JP10 and JP11. The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422 or RS-485mode, please refer to Jumper Settings COM3 Data/Power Select (JP11) The COM3 port has +5V/+12V power capability on DCD and +5V/+12V on RI by setting this 5x2-pin p=2.54mm jumper. 硬件和安装 9
2.4 Ethernet The GOT3126T-842-C is equipped with a high performance Plug and Play Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector. Please refer to detailed pin assignment list below: 2.5 Mountings: Panel / Wall / VESA There are 4 application options for the GOT3126T-842-C, Panel/Wall/Desktop/VESA mountings. 2.5.1 VESA-ARM/Wall-Mount The GOT3126T-842-C provides two ways for VESA mount: 100x100 mm. Screw four screws to fix the kit (option) in the back chassis. Wall mount: 硬件和安装 10
VESA mount: 2.5.2 Panel-mount Kit Assembly The GOT3126T-842-C is designed for panel mount application. To mount the GOT3126T-842-C, the standard set of mounting kit (included in the system packaging) is needed. 2.6 HDD Installation The GOT3126T-842-C provides a convenient Hard Disk Drive(HDD) bracket for users to install 2.5 SATA HDD. Please follow the steps: Step 1 Refer section 2.1 to open the back cover. 硬件和安装 11
Step 2 Unscrew 4 screws to take off the HDD bracket. Step 3 Fix the HDD on bracket by 4 screws. Step 4 Fix the HDD bracket into the system, and plug the data and power cable to HDD. Installation completes. 硬件和安装 12
2.7 DRAM Installation The GOT3126T-842-C provides one 204-pin DDR3 SODIMM socket that support system memory up to 2GB. Please follow steps below to install the memory modules: Step 1 Refer to section 2.1 to open the back cover and find out DIMM socket on mainboard (Mano842). Step 2 Stick the thermal pad on the back cover and rip the red mylar from it. Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is clipped by the socket. 硬件和安装 13
Step 4 Installation completes 2.8 Wireless LAN Card Installation The GOT3126T-842-C provides one Mini card slot for user to install one wireless LAN card. When installing the wireless LAN card, refer to the following instructions and illustration: Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on mainboard. Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped by the slot. 硬件和安装 14
Step 3 Find the Antenna cable and connect it wireless LAN card. Step 4 Remove the antenna plug from the top of back cover, theninstall the antenna on the antenna connector. 2.9 Power GOT3126T-842-C equips with a phoenix type power connector. It adopts 10VDC to 30VDC. Please follow the signs on power connector to connect DC power source. +: Power positive 硬件和安装 G :Safety ground :Power negative 15
Note: The safety ground must be connected to ensure the unit working appropriately. 硬件和安装 16
第三章节 AMI BIOS设置 This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility. 3.1 Starting To enter the setup screens, follow the steps below: Turn on the computer and press the <Del> key immediately. After you press the <Delete> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Chipset and Power menus. 3.2 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on. Note: Some of the navigation keys differ from one screen to another. Hot Keys + Description Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. Up/Down The Up and Down <Arrow> keys allow you to select a setup screen or Plus/Minus sub-screen. The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item. Tab The <Tab> key allows you to select setup fields. F1 The <F1> key allows you to display the general help screen. F2 The <F2> key allows you to load previous values. F3 The <F3> key allows you to load optimized defaults. F4 The <F4> key allows you to save any changes you have made and exit Esc Enter setup. Press the <F4> key to save your changes. The <Esc> key allows you to discard any changes you have made and exit the setup. Press the <Esc> key to exit the setup without saving your changes. The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens. 17
3.3 Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below. The Main BIOS setup screen is shown below. BIOS Information Display the BIOS information. System Date/Time Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format. Access Level Display the access level of current user. 18
3.4 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ACPI Settings Super IO Configuration Hardware Monitor Smart Fan Function Display Configuration Power Button Control S5 RTC Wake Settings CPU Configuration IDE Configuration OS Configuration CSM Configuration USB Configuration For items marked with, please press <Enter> for more options. 19
ACPI Settings You can use this screen to select options for the ACPI configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. Enable ACPI Auto Configuration Enable or disable BIOS ACPI auto configuration. Enable Hibernation Enable or disable system ability to hibernate (OS/S4 sleep state). ACPI Sleep State Select the ACPI (Advanced Configuration and Power Interface) sleep state. Configuration options are Suspend Disabled and S3 (Suspend to RAM). The default setting is S3 (Suspend to RAM); this option selects ACPI sleep state the system will enter when suspend button is pressed. 20
Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. For items marked with, please press <Enter> for more options. COM1~6 Use these items to set parameters related to serial port 1~6. 21
COM1 Serial Port Enable or disable serial port 1. The optimal setting for base I/O address is 3F8h and for interrupt request address is IRQ4. Change Settings Select an optimal setting for serial port. 22
Hardware Monitor This screen monitors hardware health status. This screen displays the temperature of system and CPU, cooling fans speed in RPM and system voltages (VCC_CPU, VCC_DDR, +12V, +5V, +3.3V and VBAT). 23
Smart Fan Function This screen allows you to select the fan mode. Smart Fan Function This screen allows you to select the fan mode. CPU_FAN1 Mode This item allows you to select the fan mode, which can be set to Full on Mode, Manual Mode, Auto PWM Mode or Auto RPM Mode. 24
Display Configuration Primary IGFX Boot Display Select the video device which will be activated during POST (Power-On Self Test). The default is LVDS. Backlight Control Select panel backlight control mode. LVDS Panel Type Select LVDS panel resolution; see the selection options in image above. Brightness Select the brightness of LVDS panel ranging from 30% to 100%. The default setting is 70%. 25
Power Button Control Power Button Control Restore AC Power Loss This item decides the state of system when AC power is resupplied after a power failure. Mode options are Power Off, Power On and Last State. Soft-Off by PWR-BTTN - Instant-Off: The system will shut down instantly when the power button is pressed. - Delay 4 sec: The system will shut down only when the power button is pressed and held at least 4 seconds. PS/2 KB/MS Wake Up From S5 This item decides whether or not the PS/2 keyboard or mouse can wake up the system from S5 state. 26
S5 RTC Wake Settings Wake system from S5 Enable or disable system wake on alarm event. It allows you to wake up the system in a certain time. Select Fixed Time to set the system to wake on the specified time. Use < > < > to switch among the items: Day, Hour, Minute and Second, and type the value in the selected item as you wish. For example, if you want the system to start up automatically at 14:25:26, the 13th day of each month, then you should enter 13, 14, 25, and 26 from top to bottom. 27
CPU Configuration This screen shows the CPU Configuration, and you can change the value of the selected option. Socket 0 CPU Information This item is for CPU information. Limit CPUID Maximum This item allows user to limit the maximum value of CPUID. In Windows XP environment, this item should be disabled. Execute Disable Bit Enable or disable the No-Execution Page Protection Technology. Intel Virtualization Technology Enable or disable Intel Virtualization Technology. When enabled, a VMM (Virtual Machine Mode) can utilize the additional hardware capabilities. It allows a platform to run multiple operating systems and applications independently, hence enabling a computer system to work as several virtual systems. 28
IDE Configuration In the IDE Configuration menu, you can see the currently installed hardware in the SATA ports. During system boot up, the BIOS automatically detects the presence of SATA devices. IDE Configuration In the IDE Configuration menu, you can see the currently installed hardware in the SATA ports. During system boot up, the BIOS automatically detects the presence of SATA devices. Serial-ATA (SATA) Enable or disable the SATA controller feature. SATA Speed Support Select SATA speed support. SATA Mode Determine how SATA controller(s) operate. Operation mode options are IDE Mode, AHCI (Advanced Host Controller Interface) Mode. The default is AHCI Mode. SATA 1~2 Enable or disable the onboard SATA port 1~2. 29
OS Configuration OS Selection This item allows user to select the proper Operating System. 30
CSM Configuration CSM Support Enable or disable CSM (Compatibility Support Module) support. Boot option filter Select UEFI or Legacy ROM priority. Default is UEFI and Legacy mode. PXE BootRom Enable or disable the Preboot execution Environment (PXE) boot ROM function of the onboard LAN chip during system boots up. Storage Select the execution of UEFI or Legacy storage option ROM. Default is Legacy mode. Video Select the execution of UEFI or Legacy video option ROM. Default is Legacy mode. Other PCI devices Select the execution of UEFI or Legacy option ROM of other PCI-Express network, storage or video devices. Default is Legacy mode. 31
USB Configuration USB Devices Display all detected USB devices. Legacy USB Support Use this item to enable or disable legacy support for USB devices. The default setting is Enabled. Auto option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications. XHCI Hand-off Enable or disable feature for OSes without an XHCI hand-off support. EHCI Hand-off Enable or disable feature for OSes without an EHCI hand-off support. USB Mass Storage Driver Support Enable or disable USB mass storage driver support. USB transfer time-out The time-out value for control, bulk and interrupt transfers. 32
Device reset time-out USB mass storage device start unit command time-out. Device power-up delay Maximum time the device will take before it properly reports itself to the host controller. Auto option uses default value: for a root port it is 100ms, for a hub port the delay is taken from hub descriptor. 3.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus: North Bridge South Bridge For items marked with, please press <Enter> for more options. 33
North Bridge This screen shows system memory information. South Bridge This screen allows users to configure parameters of South Bridge chipset. Audio Controller Control detection of the audio device. - Disabled: Audio device will be unconditionally disabled. - Enabled: Audio device will be unconditionally enabled. - Auto: If device is present, audio controller will be enabled, otherwise will be disabled. 34
3.6 Security Menu The Security menu allows users to change the security settings for the system Administrator Password This item indicates whether an administrator password has been set (installed or uninstalled). User Password This item indicates whether a user password has been set (installed or uninstalled). 35
3.7 Boot Menu The Boot menu allows users to change boot options of the system. Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State Use this item to select the power-on state for the keyboard NumLock. FullScreen Logo Enable or disable OEM logo display at system startup. Fast Boot Enable or disable fast boot function. BIOS skips some certain procedures to decrease system boot up time. Boot Option Priorities [Boot Option #1, ] These are settings for boot priority. Specify the boot device priority sequence from the available devices. 36
3.8 Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values Save Changes and Reset When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset. Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer. Select Discard Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to discard changes and reset. Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. Select Restore Defaults from the Save & Exit menu and press <Enter>. Save as User Defaults Select this option to save system configuration changes done so far as User Defaults. Select Save as User Defaults from the Save & Exit menu and press <Enter>. 37
Restore User Defaults It automatically sets all Setup options to a complete set of User Defaults when you select this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>. Boot Override Select a drive to immediately boot that device regardless of the current boot order. Launch EFI Shell from filesystem device Attempt to launch EFI Shell application (Shellx64.efi) from one of the available file system devices. 结束 38