PART NUMER EDIT ( 制订 ) APPROVAL SHEET ( 承认书 ) FOR CAR CHARGER ( 车载充电器 ) MODEL NO. ( 型号 ) TC08U-502400U MANUFACTURER ( 制造商 ) CONFIRM ( 确认 ) CHECK ( 审核 ) APPROVAL ( 批准 ) 郜文婷 CUSTOMER APPROVAL ( 客户承认 ) Company Add: No 158,Jiankangxi Road, JinHu Country, HuaiAn City, JiangSu Province, China. Tel:(86-517)86815568 Fax: (86-755)27343878 E- Mail: tw@tenwei.com Website: http://www.tenwei.com/ Page 1 of 10
PART NUMER CHANGE DESCRIPTION ( 版本变更描述 ) REV UP ( 变更 ) DETAIL ( 详述 ) A / / 2016-6-3 变更过流点 Page 2 of 10
PART NUMER CONTENTS 1. Apply Scope ( 适用范围 )... 4 2. Environment Protection Laws( 环保法规 )... 4 3. According with Safety and EMC Criterion( 符合的安全及电磁兼容标准 )... 4 4. Safety and EMC Approval( 已认可的安全及电磁兼容标准 )... 4 5. Input Characteristics( 输入特性 )... 4 5.1 Rated Input Voltage ( 额定输入电压 )... 4 5.2 Rated Input Current( 额定输入电流 )... 4 5.3 Efficiency ( 效率 )... 4 6. Output Characteristics( 输出特性 )... 4 6.1 Rated Output Voltage( 额定输出电压 )... 4 6.2 Output Voltage ( 输出电压范围 )... 5 6.3 Rated Output Current ( 额定输出电流 )... 5 6.4 Rated Power ( 额定功率 )... 5 6.5 LED Indicate Function (LED 指示功能 )... 5 6.6 Output Ripple and Noise ( 输出纹波 噪音 )... 5 6.7 Protection ( 保护 )... 5 6.7.1 Over Current Protection ( 过流保护 )... 5 6.7.2 Short Circuit Protection ( 短路保护 )... 5 7. Mechanical Requirement ( 机械要求 )... 5 7.1 Dimension ( 尺寸 )... 5 7.2 Weight ( 重量 )... 6 7.3 Color ( 颜色 )... 6 7.4 US Plug Type(US 接口类型 )... 6 7.5 Drop Test ( 跌落试验 )... 6 7.6 Vibration Test Requirement ( 振动试验 )... 6 7.7 Plug In and Out Test ( 插拔实验 )... 6 7.8 Salty Fog Test for Metal Part ( 五金件盐雾实验 )... 7 8. Mechanical Characteristics ( 机械性能 )... 7 8.1 Appearance ( 外观 )... 7 8.2 Case/Resin Materials ( 外壳材质 )... 7 9. Environmental Performances( 环境性能 )... 7 9.1 Operating temperature range( 工作温度范围 )... 7 9.2 Stored temperature range( 存储温度范围 )... 7 9.3 Operating at the invariable temperature and invariable humidity( 恒温恒湿工作 )... 7 10. Product Outline Drawing ( 制品结构图 )... 8 11. Packing Drawing ( 装箱图 )... 9 Page 3 of 10
PART NUMER 1. Apply Scope ( 适用范围 ) This specification shall be applied to car charger 5V/2.4A 本规格适用于 5V/2.4A 车载充电器 2. Environment Protection Laws( 环保法规 ) ROHS REACH CPSIA EN71 PHTHALATE HALOGEN 3. According with Safety and EMC Criterion( 符合的安全及电磁兼容标 准 ) EN60950-1 EN61558-1 EN60065-1 EN55022 UL60950-1 UL1310 UL60065-1 EN55024 4. Safety and EMC Approval( 已认可的安全及电磁兼容标准 ) C TUV/GS CE PSE UL FCC SAA C-tick KC CCC TLC E-mark 5. Input Characteristics( 输入特性 ) 5.1 Rated Input Voltage ( 额定输入电压 ) It is normal for 12Vdc to 24Vdc input DC voltage. ( 额定输入直压 12V~24V) 5.2 Rated Input Current( 额定输入电流 ) It is normal for 0A to 1.8A input current ( 额定输入直流 0A~1.8A) 5.3 Efficiency ( 效率 ) 75%min measured at 12Vdc to 24Vdc input voltage, maximum load ( 在输入电压 12Vdc-24Vdc, 输出最大负荷下, 工作效率大于 75%) 6. Output Characteristics( 输出特性 ) 6.1 Rated Output Voltage( 额定输出电压 ) The rated output voltage is specified at DC 5.0V ( 额定输出电压 DC 5.0V) Page 4 of 10
PART NUMER 6.2 Output Voltage ( 输出电压范围 ) load voltage ( 负载输出电压范围 ): DC 4.7V-5.3V(I=0.1A~2.4A) 6.3 Rated Output Current ( 额定输出电流 ) Output current will be performed from 2.4A. ( 额定输出电流 2.4A) 6.4 Rated Power ( 额定功率 ) The rated power is 12Watts ( 输出功率 12 Watts) 6.5 LED Indicate Function (LED 指示功能 ) No Load: Green ( 空载 : 绿灯 ) Load: Green ( 负载 : 绿灯 ) 6.6 Output Ripple and Noise ( 输出纹波 噪音 ) Output ripple voltage is less than 150 mv p-p measured methods: Performed by 20MHz bandwidth in oscilloscope Applied 0.1uF ceramic capacitor and 10uF electrolytic capacitor across output connector terminals Measured at the end of DC cable. ( 输出端并 0.1uF 与 10uF 电容, 限制示波器带宽 20MHz 时, 测得纹波小于 150mV p-p) 6.7 Protection ( 保护 ) 6.7.1 Over Current Protection ( 过流保护 ) Output current will be limited and less than 4.0A ( 输出过流保护电流 4.0A) 6.7.2 Short Circuit Protection ( 短路保护 ) The charger is protected that a short happened between the output terminals and shall not result in a fire hazard, any damage to this Charger and will be normal operation automatically while the short is removed.. ( 输出短路后不损坏该制品, 短路恢复正常输出 ) 7. Mechanical Requirement ( 机械要求 ) 7.1 Dimension ( 尺寸 ) 49(L) * 25(D) mm maximum Page 5 of 10
PART NUMER 7.2 Weight ( 重量 ) 15g ±5g 7.3 Color ( 颜色 ) lack ( 黑色 ) 7.4 US Plug Type(US 接口类型 ) Plug: ig 4pin US,Pin1 +,PIN4 -,Pin2&Pin3 short ( 大 4pin US,2/3PIN 短路 ) 7.5 Drop Test ( 跌落试验 ) Drop the car charger from a height of 100cm onto a hardwood floor, hitting the car charger for 6 times, no mechanical damages or other failures, no electrical deterioration and other failures comparing to before test condition. ( 制品从 100cm 处落下 6 次, 落下的方向任意, 落在硬木地板上, 实验后与实验前状态比较没有 机械破损等不良状况, 且不出现电器性能损坏 ) 7.6 Vibration Test Requirement ( 振动试验 ) Non-operating, with packing) Reference to IEC publ. 68-2-6 ( 在包装好不工作的情况下实验, 具体参照 IEC publ. 68-2-6 标准 ) Frequency( 振动频率 ) Sweep ( 振动方式 ) Acceleration( 加速度 ) Displacement( 振幅 ) Test conditions( 测试条件 ) Acceptance Criteria( 规格 ) 10~55Hz 2hours, For each axis(x,y,z) 0.6G 1.5G (5~50Hz, peakpeak) 0.35 mm(5~50hz) Nominal functional test should be satisfied after the test ( 不发生功能损坏的异常情况 ) 7.7 Plug In and Out Test ( 插拔实验 ) After plug the connector in(30n max) and out(10-50n) the female-connector for 10 times, then plug in and out for 1000 times, light damage in the mechanic characteristic, but no abnormality in electric characteristic. ( 插头与连接器经正常插拔 10 次, 插头每次插入力度不大于 30N, 拔出在 10-50N 之间后持续拔插 1000 次 外观允许有轻度损伤, 但导通性能良好 ) Page 6 of 10
PART NUMER 7.8 Salty Fog Test for Metal Part ( 五金件盐雾实验 ) Experiment condition, Salty water thickness: 5%, Equipment Temperature: 35~40, put the charger in the test equipment for 8h (metal parts for 8h), after 8h recovery at 25 checking the appearance, the metal parts have no erode and rust ( 盐雾试验要求 : 调制 ( 工业盐 ) 盐水的浓度为 5%, 设备温度设置为 35~40, 放入盐雾试验设备中持续喷雾 8 小时 ( 金属部分 8 小时 ), 试验结束后取出, 在常温下搁置 8 小时, 再检查充电器外观 ; 要求金属部分不生锈 ) 8. Mechanical Characteristics ( 机械性能 ) 8.1 Appearance ( 外观 ) Visual inspection the case have no visual abnormality, no obvious nick, burr and other mechanical damage, outer metal have no rust. Use limit sample to check for any failures. ( 目视检查, 无外观异常, 表面无明显划痕 毛刺及其它机械损伤, 外露金属部分无锈, 其它限度根据样品确认 ) 8.2 Case/Resin Materials ( 外壳材质 ) Flame resistance applies to UL94V-0 ( 耐燃性遵循 UL94V-0) 9. Environmental Performances( 环境性能 ) 9.1 Operating temperature range( 工作温度范围 ) The product should operate at 0~40, test of operating for 2 hours at 0 ±2 and 40 ±2. ( 该产品工作温度范围为 0~40, 低温 0 ±2 和高温 40 ±2 工作试验各 2 小时 ) 9.2 Stored temperature range( 存储温度范围 ) The product should be stored at -25~70,test of non-operated for 16 hours at -25 ±2 and 70 ±2. ( 该产品存储温度范围为 -25~70, 非工作状态下进行低温 -25 ±2 和高温 70 ±2 存储试验各 16 小时 ) 9.3 Operating at the invariable temperature and invariable humidity( 恒温恒湿工作 ) The product should operate at 40 ±2,90~95%RH, test of operating for 48 hours(full load) ( 该产品恒温恒湿工作环境为 40 ±2, 90~95%RH, 满载工作状态下进行试验 48 小时 ) Page 7 of 10