萬 達 光 電 科 技 股 份 有 限 公 司 PRODUCT SPECIFICATIONS 產 品 規 範 書 Customer ( 客 戶 ): Model ( 型 式 ): T170S-5RB004N-0A18R0-200FH Mode ( 種 類 ): Five-wire Analog Touch Panel Date ( 日 期 ): May 06, 2008 Version ( 版 本 ): 6.3 Customer Approval 客 戶 簽 認 HIGGSTEC INCORPORATED 8 F., No. 609, Wan Shou Rd., Sec. 1, Kweishan, Taoyuan Hsien 33350, Taiwan. TEL:886-2-8209-9696 FAX:886-2-8200-3030 E-mail:info@higgstec.com.tw Approve Review Preparation 確 認 審 訂 製 表 Henry Andy Young
TABLE OF CONTENTS 目 錄 00. Specification Revision Record [ 規 格 變 更 記 錄 ]... 01 00. Dimension Drawing [ 尺 寸 圖 ].... 02 01. Scope [ 範 圍 ]... 03 02. Features [ 特 性 ]... 03 03. General Specification [ 一 般 規 格 ].... 03 04. Environmental Characteristics [ 環 境 特 性 ].. 03 05. Optical Characteristics [ 光 學 特 性 ]. 04 06. Electrical Characteristics [ 電 子 特 性 ]. 04 07. Mechanical Characteristics [ 機 械 特 性 ].... 05 08. Reliability [ 可 靠 度 ].. 05 09. Durability [ 耐 久 性 ].. 05 10. Inspection Methods [ 檢 查 方 法 ]... 06 11. Appearance Inspection [ 外 觀 檢 查 ]. 07 12. Attention for Mounting Condition [ 裝 機 注 意 事 項 ].... 08 13. Warranty [ 保 固 ].. 09 14. Appendices [ 附 註 ]. 09 Appearance Specification [ 外 觀 檢 查 規 格 ]. 11 15. Caution [ 注 意 事 項 ].... 10 Date: May 06, 2008 Version: 6.3
SPECIFICATION REVISION RECORD 規 格 變 更 記 錄 Customer [ 客 戶 名 稱 ]: Date [ 發 行 日 期 ]:May 06, 2008 Customer NO. [ 客 戶 編 號 ]: Model [ 型 式 ]:T170S-5RB004N-0A18R0-200FH NO. [ 項 次 ] Version. [ 版 本 ] Date [ 變 更 發 行 日 期 ] Summary of Changes [ 變 更 內 容 摘 要 ] Page [ 變 更 頁 碼 ] <Remarks>[ 備 註 欄 ] Date: May 06, 2008 Version: 6.3 Page: 01/11
01. Scope [ 範 圍 ] 02. Features [ 特 性 ] 03. General Specification [ 一 般 規 格 ] The specification is for Five-Wire Analog Resistive touch panel. [ 此 規 格 適 用 於 五 線 - 類 比 電 阻 式 觸 控 屏 幕 ] Item [ 項 目 ] Specifications [ 規 格 ] (1) Type Five-Wire Analog Resistive [ 型 式 ] [ 五 線 - 類 比 電 阻 式 ] Input Mode Stylus or Finger (2) [ 操 作 模 式 ] (3) Cable [ 連 結 線 ] [ 筆 觸 或 手 觸 ] FFC Item [ 項 目 ] Specifications [ 規 格 ] Frame Size (1) 356.00±0.30 X 286.50±0.30 mm (2) (3) (4) (5) [ 外 框 尺 寸 ] View Area [ 可 視 區 ] Active Area [ 動 作 區 ] Total Thickness [ 總 厚 度 ] Tail Length [ 出 線 長 度 ] 343.00±0.20 X 275.50±0.20 mm 337.00±0.20 X 269.50±0.20 mm 2.20±0.20 mm 205.00±6.00 mm 04. Environmental Characteristics [ 環 境 特 性 ] Item [ 項 目 ] (1) Operation [ 操 作 ] (2) Storage [ 儲 存 ] Temperature [ 溫 度 ] -10 C ~ +70 C -40 C ~ +80 C Note: All terms under 1 atmosphere. [ 註 : 於 正 常 的 1 大 氣 壓 下 ] Specifications [ 規 格 ] Humidity [ 濕 度 ] (Non Condensing) [ 未 凝 結 ] 20%RH ~ 80%RH 10%RH ~ 85%RH Date: May 06, 2008 Version: 6.3 Page: 03/11
05. Optical Characteristics [ 光 學 特 性 ] 06. Electrical Characteristics [ 電 子 特 性 ] Item [ 項 目 ] Specifications [ 規 格 ] (1) Transparency 80% ± 3% [ 透 光 度 ] (Measured by BYK-Gardner ) (2) Haze 8% ± 3% [ 霧 化 度 ] (1) Item [ 項 目 ] Specifications [ 規 格 ] Loop Resistance [ 迴 路 阻 抗 ] (2) Linearity [ 線 性 ] (3) Chattering [ 作 動 時 間 ] (4) Insulation [ 絕 緣 阻 抗 ] (5) Endurance [ 耐 電 壓 ] X:20~500Ω, Y:20~500Ω (See Figure 6-1) X 1.0%, Y 1.0% (See Figure 10-2) 15ms 20MΩ/25V(DC) No acting damage at DC50V/60sec. Figure 6-1 Loop Resistance X = short RT and RL, short LT and LL, measure the resistance between RT and LT Loop Resistance Y = short RT and LT, short RL and LL,measure the resistance between RT and RL Date: May 06, 2008 Version: 6.3 Page: 04/11
07. Mechanical Characteristics [ 機 械 特 性 ] Item [ 項 目 ] Specification [ 規 格 ] Condition [ 條 件 ] Operating Force Stylus=R0.8 50g [ 作 動 力 ] Impact [ 撞 擊 ] Static Load [ 靜 態 承 重 ] Hardness [ 硬 度 ] Peeling [ 剝 離 ] Bending [ 繞 折 ] [ 筆 式 =R0.8] 13.0ψDIA. Steel Ball/9g Height=30cm [13ψ/9g 鋼 球 高 度 =30cm] 500g within 10cm ² area for 30sec [500g 置 於 10cm² 內,30 秒 ] 3H pencil, pressure 1N/45 [ 鉛 筆 3H, 壓 力 1N/45 (JIS K5400)] 800g by vertical 90 [800g, 垂 直 90 ] 135 10 times left & right [135 角, 左 右 來 回 10 次 ] 1 time, no damage [Impact at center area] [ 中 央 區 域 撞 擊 1 次, 不 能 破 損 ] Satisfy(1) of Item 7 and (1), (2),(4) of Item 6 [ 符 合 7 項 目 (1) 及 6 項 目 (1),(2),(4)] 3H Satisfy (1) of Item 6 [ 符 合 6 項 目 (1)] Satisfy (1) of Item 6 [ 符 合 6 項 目 (1)] 08. Reliability [ 可 靠 度 ] Item [ 項 目 ] Specification [ 規 格 ] Condition [ 條 件 ] High Temperature /Humidity [ 高 溫 高 濕 ] High temperature [ 高 溫 ] Low temperature [ 低 溫 ] Thermal Cycle [ 冷 熱 循 環 ] 70 C /90%RH, 500 hrs, allow panel stays in normal environment for 4 hrs [70 C /90%RH,500 小 時, 回 常 溫 4 小 時 後 始 可 測 試 ] 70 C /500 hrs allow panel stays in normal environment for 4 hrs [70 C /500 小 時, 回 常 溫 4 小 時 後 始 可 測 試 ] -40 C /500 hrs allow panel stays in normal environment for 4 hrs [-40 C /500 小 時, 回 常 溫 4 小 時 後 始 可 測 試 ] -40 C ~70 [60 min./cycle] *100 cycles allow panel stays in normal environment for 4 hrs [-40 C ~70 C, 每 循 環 60 分 鐘, 共 100 次 循 環, 回 常 溫 4 小 時 後 始 可 測 試 ] Reliability test may cause the film puffed yet the electric characteristic stays intact. (1), (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies X 2.0%, Y 2.0%;Actuation force must not exceed 150g after reliability test. 經 由 可 靠 度 測 試 後, 外 觀 不 在 其 規 範 內, 但 功 能 性 仍 符 合 以 下 條 件 [ 符 合 5 項 目 (1) (2) 及 6 項 目 (1) (4) ; 6 項 目 (2) 符 合 X 2.0%, Y 2.0%; 測 試 後 作 動 力 不 能 超 過 150g] 09. Durability [ 耐 久 性 ] Item [ 項 目 ] Specification [ 規 格 ] Condition [ 條 件 ] Knock Test 35,000,000 times Satisfy (1), (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies X 2.0%, Y 2.0%; Actuation force must not exceed 150g after durability [ 觸 擊 測 試 ] [3500 萬 次 ] test. [ 符 合 5 項 目 (1) (2) 及 6 項 目 (1) (4) ; 6 項 目 (2) 符 合 X 2.0%, Y 2.0%; 測 試 後 作 動 力 不 能 超 過 150g] Date: May 06, 2008 Version: 6.3 Page: 05/11
10. Inspection Methods: [ 檢 查 方 法 ] (1) Linearity Condition [ 線 性 測 試 條 件 ] Step 1: short RT and RL(or short RL and LL). Step 2: apply voltage DC 5V. Step 3: short LT and LL (or short RT and LT). Step 4: apply grounding. Step 5: draw points along LX and LY at 5.0mm intervals within pattern area and detect the voltage at SG. Step 6: measure the voltage differences between RT and LT (or RT and RL) (Fig 10-1) (Fig 10-2) [ 將 RT, RL 短 路 ( 或 RL, LL 短 路 ) 並 接 上 5V 的 直 流 電, 另 外 將 LT, LL 短 路 ( 或 RT, LT 短 路 ) 並 接 上 接 地 線 圈 0V, 以 5.0mm 的 間 隔, 利 用 手 寫 筆 (stylus) 劃 直 線 ( 如 圖 2 中 LX 和 LY), 並 量 測 SG 的 電 壓, 量 測 並 計 算 RT 與 LT 間 的 電 位 差 ( 或 RT 與 RL 間 的 電 位 差 ) ] (Fig 10-1) (Fig 10-2) Figure 10-1 Figure 10-2 Linearity: [ Vxm-Vxi ] / (Va-Vb) X 100% (2) Specification [ 規 範 ] Linearity must meet the electrical characteristic specified in Item 6 [ 線 性 必 須 符 合 6 項 目 的 電 性 規 範 ] Date: May 06, 2008 Version: 6.3 Page: 06/11
11. Appearance Inspection [ 外 觀 檢 查 ] (1) A 17W fluorescent luminant lamp is used for appearance inspection. Detail settings are shown in (Fig 11-1) and (Fig 11-2). [(1) 檢 測 始 用 之 燈 光 為 一 盞 17W 白 熾 燈 光, 詳 細 的 擺 設 方 式, 請 參 考 圖 (Fig11-1), (Fig11-2) ] (2) Minor impurities outside viewing area are acceptable unless their existance affect electrical functions. [(2) 只 要 不 影 響 電 器 功 能 性, 可 視 區 外 之 外 觀 暇 疵 是 可 以 被 允 許 的 ]. Figure 11-1 Figure 11-2 (3) Glass Flaw [ 玻 璃 瑕 疵 ] Item [ 項 目 ] Picture [ 圖 示 ] Specification [ 規 格 ] Corner Flaw [ 角 瑕 疵 ] X 3.0mm Y 3.0mm Z T Edge Flaw [ 邊 緣 瑕 疵 ] X 3.0mm Y 3.0mm Z T Progressive Flaw [ 裂 縫 瑕 疵 ] Not allowed [ 不 允 許 ] Note: T=Glass thickness (4) Please refer to AppendixⅠ:Appearance Specification. [(4) 外 觀 規 格 請 詳 見 ( 附 註 1)] Date: May 06, 2008 Version: 6.3 Page: 07/11
12. Attention of Mounting Condition [ 裝 機 注 意 事 項 ] (1) The gasket support of touch panel must allocate outside of Viewable Area. Reserve enough clearance between panel surface and enclosure for normal panel operation. To avoid pressing error, please retain enough space between surface panel and Bezel. [ 請 將 固 定 觸 控 屏 用 的 支 撐 體 (support) 設 計 於 可 視 區 (Viewable area) 之 外 為 避 免 不 小 心 碰 到 觸 控 屏 而 產 生 動 作, 請 預 留 空 間 於 面 板 與 機 體 外 殼 之 間 ] (2) Bezel opening must not touch Viewable Area, Bezel opening must be designed between Viewable Area and Active Area. [ 外 殼 內 緣 (Bezel opening) 應 設 計 於 可 視 區 及 動 作 區 之 間, 並 且 不 得 碰 到 可 視 區 ] (3) We recommend elastic material support. [ 建 議 使 用 彈 性 物 質 製 成 的 支 撐 體 ] (4) Due to the conductive characteristic of the panel backside, prevent metal contact after mounting. [ 觸 控 屏 面 板 背 面 具 導 電 性 質,