Bluetooth 2.0/2.1 YXY-BT2417 蓝牙模组技术规格书 ( 版本 :V2.8 密级 :R1) 深圳市永芯益科技有限公司 2013 http://www.yorxin.com Page 1 of 9
修订记录 修订者日期修订版变更内容 Kevin 2011-04-10 V1.0 创建初稿 Kevin 2011-04-21 V2.0 更新 PCB 接口 Kevin 2011-04-25 V2.1 更新 Pin 脚说明 Kevin 2011-05-16 V2.8 完善软件说明 http://www.yorxin.com Page 2 of 9
目录 1. 产品概述... 4 2. 应用领域... 4 3. 硬件尺寸图... 5 4. Pin 脚定义... 5 5. 电气特性... 7 6. 功耗参数... 7 7. 参考设计... 8 8. 软件说明... 9 http://www.yorxin.com Page 3 of 9
1. 产品概述 YXY-BT2417 蓝牙模组 ( 以下简称 BT2417 模组 ), 是支持蓝牙 2.0/2.1 标准协议的蓝牙模组, 基于 CSR BlueCore4-Ext(BC417) 蓝牙芯片与 Flash 存储芯片架构, Class2 模式传输距离达 10 米 该模组具备工业级设计 高灵敏性接收 数据传输稳定 低功耗 体积小巧 操作简单以及成本优势, 已经广泛用于蓝牙数据传输领域, 堪称经典之作 支持标准 BT2.0/2.1+EDR, 上下兼容 ; 支持 SPP 协议, 最高可支持 3M 调制模式 ; 支持 UART 接口, 支持 1200bps~2764800bps 波特率 ; 内置 8M Flash, 可以定制开发多种蓝牙 Profile 固件 ; 提供 I2C USB PCM 接口,12 路 PIO,2 路 AIO; 支持低功耗模式, 蓝牙 Class2 模式 ; 数据加密 工业级设计 ; 板载 PCB 天线 输入电压 3.3V; 2. 应用领域 BT2417 模组主要用于短距离的数据无线传输领域, 其标准程序采用 UART 接口支持蓝牙 SPP 协议, 可以同所有具备蓝牙功能的安卓版本手机 笔记本 电脑以及蓝牙模块配对连接, 从而双向收发数据 避免繁琐的线缆连接, 能直接替代现有的串口线 手机 计算机周边设备 ; 蓝牙打印机 条码扫描设备 ; 工业遥控 遥测 ; POS 系统, 无线键盘 鼠标 智能家居 工业控制 ; 无线抄表 数据采集 传感器设备 ; 医疗设备无线数据传输 ; 车载仦器无线数据传输 ; 无线 LED 显示屏系统 无线遥控器 游戏手柄 玩具遥控 ; http://www.yorxin.com Page 4 of 9
3. 硬件尺寸图 图 1. 硬件尺寸 4. Pin 脚定义 图 2. PIN 脚分布 http://www.yorxin.com Page 5 of 9
Table1: Pin Function Descriptions PIN NAME I/O FUNCTION 1 UART_TX O Uart Tx: Data Send out 2 UART_RX I Uart Rx: Data Receive in 3 UART_CTS I Uart clear to send, active low 4 UART_RTS O Uart request to send, active low 5 PCM_CLK I/O PCM data clock 6 PCM_OUT O PCM data output 7 PCM_IN I PCM data input 8 PCM_SYNC I/O PCM data strobe 9 AIO0 I/O Analogue input/output line 10 AIO1 I/O Analogue input/output line 11 RESET I Internal pull-up Reset if low for >5ms 12 VDD I VCC input 3.3V 13 GND - Ground 14 NC 15 USB_DN- I/O USB data minus 16 SPI_CSB I Chip select for serial peripheral interface, active low 17 SPI_MOSI I Serial peripheral interface data input 18 SPI_MISO O Serial peripheral interface data output 19 SPI_CLK I Serial peripheral interface clock 20 USB_DP+ I/O USB data plus with selectable internal 1.5kΩ pull-up 21 GND - Ground 22 GND - Ground 23 PIO0 I/O Programmable input/output line 24 PIO1 I/O Programmable input/output line 25 PIO2 I/O Programmable input/output line 26 PIO3 I/O Programmable input/output line 27 PIO4 I/O Programmable input/output line 28 PIO5 I/O Programmable input/output line 29 PIO6 I/O Programmable input/output line 30 PIO7 I/O Programmable input/output line 31 PIO8 I/O Programmable input/output line 32 PIO9 I/O Programmable input/output line 33 PIO10 I/O Programmable input/output line 34 PIO11 I/O Programmable input/output line http://www.yorxin.com Page 6 of 9
5. 电气特性 Table2: Electrical characteristics Rating Value Unit Supply voltage(vdd) 3.0 ~ 3.6 V Voltage on I/O pin VDD±0.4 V Work temperature range -20 ~ +70 Storage temperature range -40 ~ +125 RF power(basic Rate) 4 db RF sensitivity(basic Rate) -87 db RF power(edr) 2 db RF sensitivity (EDR) -85 db 6. 功耗参数 Table3: Power consumption BT State Role Baud Rate(kbps) Iaverage Unit Page scan - 115.2 0.42 ma Inquiry and page scan - 115.2 0.76 ma ACL No traffic Master 115.2 4.60 ma ACL With file transfer Master 115.2 10.3 ma ACL No traffic Slave 115.2 17.0 ma ACL With file transfer Slave 115.2 24.7 ma ACL 40ms sniff Master 38.4 2.40 ma ACL 1.28s sniff Master 38.4 0.37 ma SCO HV1 Master 38.4 39.2 ma SCO HV3 Master 38.4 20.3 ma SCO HV3 30ms sniff Master 38.4 19.8 ma ACL 40ms sniff Slave 38.4 2.11 ma ACL 1.28s sniff Slave 38.4 0.42 ma Parked 1.28s beacon Slave 38.4 0.20 ma SCO HV1 Slave 38.4 39.1 ma SCO HV3 Slave 38.4 24.8 ma SCO HV3 30ms sniff Slave 38.4 19.0 ma Standby Host connection(a) - 38.4 40 µ A Reset (RESETB low)(a) - - 34 µ A Note: Typical Peak Current is 57.9 ma during cold boot. http://www.yorxin.com Page 7 of 9
7. 参考设计 图 3. SPP 应用电路参考设计 http://www.yorxin.com Page 8 of 9
8. 软件说明 BT2417 模组支持软件定制开发, 根据客户的要求进行参数设置 更改 PIO 指示位置以及特定应用等 默讣状态下,BT2417 模组烧录标准 SPP 程序, 其参数如下 : 蓝牙名称 :YXY-BT2417 配对码 :1234 串口参数 :38400,8 数据位,1 停止位, 无校验 连接指示 :GPIO9 未连接, 输出低电平 ; 已连接, 输出高电平 状态指示灯 :GPIO8 指示模组主从以及配对连接状态 标准 SPP 程序主从一体, 支持多种接口 AT 指令 ( 字符行指令, 以回车换行 \r\n 作为指令结尾 ) 配置参数, 一次设置好后永久保存参数, 模组需重新上电自动生效 参见具体指令说明, 获取更多开发资料 http://www.yorxin.com http://www.yorxin.com Page 9 of 9