NO. 1 2 3 4 5 6 Max. charge voltage 充电上限电压 Min. discharge voltage 放电终止电压 Max. continuation charge current 最大连续充电电流 units 单位 V s 参数 5V V 2.4V ma 1100mA Max continuous discharge current 最大连续放电电流 ma 1100mA Standardenvironm temperature 温度 25±5 ent 标准环境 Humidity 湿度 RH 45-75%RH Operating tempe rature 工作温度 Charging 充电 0~45 Discharging 放电 -20~+60 Remark 备注 7 8 9 Charging time 充电时间 About Weight 大约重量 Outgoing voltage 出货电压 standard charge 标准充电 quick charge 快速充电 H 5.5H 0.2C 220mA H 3.0H 550mA g 19g V 3.7-4.2V 3.2 Performance inspection and testing 性能检查及测试 NO. Content 内容 Requirement 要求 1 Standard charge 标准充电 Charging the cell initially with constant current at 0.2C and then with constant voltage at 4.2V till charge current declines to0.02c 以 0.2C 恒流充电至 4.2V, 再改为恒压充电, 直至充电电流 0.02C 时停止 Constant current constant voltage source 恒流恒压源 Version 版本 : A0 3
2 Normal capacity 标称容量 The capacity means the discharge capacity of the cell, which is measured with discharge current of 0.2C with 3.0 V cut-off voltage after standard charge. 标称容量是指电池标准充电后, 以标准放电 (0.2C) C 1100mAh 至终止电压 3.0V 的容量 3 Cycle life 循环寿命 Test condition: Charge: 0.2C to 4.2V Discharge: 0.2C to3.0v 80% or more of 1 st cycle capacity at 0.2C discharge of Operation. 测试条件 : 充电 :0.2C 充电到 4.2V 500 次 500 times 放电 :0.2C 放电到 3.0V 当放电容量降至初始容量的 60% 时, 所完成的循环次 数定义为该电池的循环寿命 4 Temperature Characteristics 温度特性 1. According to item Standard Charge. 2. Capacity comparison at each temperature, measured with constant discharge current 0.2C with 3.0V cut-off. Percentage as an index of the capacity compared with 100% at 25. 1. 将电池标准充电 -20 : 20% 25 : 100% 60 : 85% 2. 在不同温度条件下, 用 0.2C 的电流恒流放电至截 止电压 3.0V 以 25 时放电容量为基准计算百分比 4 PCM parameter PCM 参数 4.1 PCM 参数 Symbol Content Criterion 符号 详细内容 标准 Over charge Protection 过充保护 V DET1 tv DET1 V REL1 Over charge detection voltage 过充电检测电压 Over charge detection delay time 过充电检测延迟时间 Over charge release voltage 过充电解除电压 4.30±0.05V 200ms max 4.10±0.05V Version 版本 : A0 4
Over discharge protection 过放保护 Over current protection 过流保护 Short protection 短路保护 Interior resistance 内阻 VDET2 tvdet2 VREL2 VDET3 IDP tvdet3 TSHORT RDS Over discharge detection voltage 过放电检测电压 Over discharge detection delay time 过放电检测延迟时间 Over discharge release voltage 过放电解除电压 Over current detection voltage 过电流检测电压 Over current detection current 过电流保护电流 Detection delay time 检测延迟时间 Release condition 保护解除条件 Detection condition 保护条件 Detection delay time 检测延迟时间 Release condition 保护解除条件 Main loop electrify resistance 主回路通态电阻 2.40±0.1V 100ms max 3.00±0.1V 150±30mV 2-5A 20ms max Cut load 断开负载 Exterior short circuit 外部电路短路 50ms max Cut short circuit 断开短路电路 VC=4.2V,R DS 60mΩ Current consumption 消耗电流 IDD Current consume in normal operation 工作时电路内部消耗 3.5μA Type 6.0μA Max 4.2 PCB component list 主要元件清单 No. 元件编号 Part name 元件名称 元件规格 封装形式 Pack type 用量 Q ty 1 U1 2 U2 3 R1 单节锂电保护 IC Battery protection IC MOS 管 Silicon MOSFET 贴片电阻 Resistance G3J SOT-23-6 1 8205 TSSOP-8 1 SMD 100Ω±5% 0603 1 Version 版本 : A0 5
4 R2 5 C1 6 PCB 贴片电阻 Resistance 贴片电容 Capacitance 印制电路板 Print circuit board SMD 1KΩ±5% 0603 1 SMD 0.1μF 0603 1 FR4, 双面板 ±0.15mm 1 4.3 Application Schematic 原理图 Version 版本 : A0 6
5 Dimensions of battery pack 成品结构尺寸 Item T W L L1 说明 Description 厚度 Thickness 宽度 Width 长度 Length 出线长度 Wire length 尺寸规格 6.0mm max 35.0mm max 52.0mm max JST-PH 2.0connector UL1571 100# 50 ±5mm Version 版本 : A0 7