MTK
1. 1.1 SMT BSN 1.2 1 IMEI 2. 2 2.1 MTK Flash Flash NAND FlashMP3 1 SMT SOFT Flash 2 SOFT
MKT USB-RS232 921600 8 2.2 COPY 2.3 USB PCUSB USB 8 USB USB USB-RS232 (USB ) RS232 PCRS232 8 4V2A 2.4 DA File Scatter File ROM Step 1 SMT MutiDL_SMT MultiPortFlashDownloadProject.exe MutiDL_Update MultiPortFlashDownloadProject.exe 3
Step 2 DA File MTK_AllInOne_DA.bin Step 3 Scatter File scat_rom.txt Step 4 2 ROM Step 5 2 open FAT file scat_rom_fat.txt Step 6 SMT Download ROM and Format Download ROM Step 7 USB-RS232 921600~460800 RS232 115200 MultiPortFlashDownloadProject.INI [form]-> TheFirstComPortNo COM1 TheFirstComPortNo=1 COM3 TheFirstComPortNo=3 2.5 Step 4 download start DL OK 2.6
5 pinpower keygnd 3.BSN 3.1 BSN(board serial number)smt BSN 5 8 00001116 +D +B +V +M 4 3.2 COPY 3.2 PC
3.3 5 Step 1 SN_Station_V1.2.5_07.05\setup, \\SN_STATION\ SN_STATION.EXE Step 2, 115200. Step 3 Step 4, 0.00 Step 5 IC Step 6,: ; META:. normal Step 7,BarcodeIMEI Step 8 NVRAM
6 3.4 7, Initial NVRAM, START, 7. PASS Status Display.
3.5 USB-RS232 USB-RS232 BSN/IMEI. 4. 4.1 MTK_ATEDEMO.EXE MTK_ATEDEMO.EXE AFC APC Path Loss ADC AFC APC Path Loss ADC 4.2 MTK_ATEDEMO.EXE MTK_ATEDEMO.EXE Copy Delete 4.3 4.3.1 Generic Pentium III or above PC Agilent 8960 CMU200 Agilent66xx Keithly23xx GPIB NIAgilent(and Driver) RF Cable/ 4.3.2
8 4.3.3 PC-PC- NI Measurement & Automation NI GPIB My Sestem\Device and Interface\GPIB0 Scan for Instruments GPIB0 PC--GPIB GPIB GPIB 9 PC RS232- PC,9 AT, OK COM
10 4.4 MTK_atedemo.exe,Configuration->CalSetting 12report & System 13
11 12 1 2 a. GSM900 DCS1800 b. c.ft d.tx Power RX Level 34 3 C0 for GSM900:70; C0 for DCS1800:700; AFC_Calibration_Number:10AFC_DAC1 Value:4000; AFC_DAC2 Value:5000; Number of Frame measurement:5;number of Measurement:4. Down Link Power:-60.00
13,,,, Fast Power Measurement: wireless test: GSM default Items: GSM Stop condition: RF final test with check Bar code: RF Final test with IMEI write:imei Calibration Test Setting,13 TEST MODE SELECT, Manual Initial Bar Code Get Type When Calibration Power Supply Type Radio Communiction Tester Baseband Chip Type CMU Measurement Port COM Port Select COM Power Supply GPIB Address:GPIO, Cal INP LOSS, Cal OUP LOSS,
NVRAM Database file: NVRAM Config file location: Calibration file location: Test setup file location: Test report location: Report database location: 4.5 Initial Calibration,14 Calibratin Test Calibratin Test Trace Please Connect with Mobileand wait Sync to target PASS 14 4.6 AFC Calibration Fail = 270 Pathloss Calibration Fail = 271 APC Calibration Fail = 272 PHASE ERROR Calibration Fail = 273
ADC Calibration Fail = 274 BLER Fail = 116 1. 272 (15). GSM900 7 MTK APC APC DAC-Power DAC 15 META_6218B.CFG., 2. 271(16). DCS1800 740( 4dB)
16 RF. DCS1800, +SAW filter.,ic. 5. 5.1, MTK_ATEDEMO.exe CMU200Agilent8960CMD55 5.2 4.1 5.3 4.2
4.3.3 5.4 MTK_atedemo.exe,Configuration->FinallSetting 17report & System 13 17 Select reset RF function group: RF, GSM900 SIG Call setup configuration: Measurement configuration: 17. Rx Quality
GSM900(IN OUT) 0.3dBm DCS1800(IN OUT)0.5 dbm GSM900 62CH 5PCL TX Power 31.9dBm DCS1800 698CH 0 PCL TX Power 28.8 dbm GSM900 62CH 5PCL TX Power 31.5dBm DCS1800 698CH 0 PCL TX Power 28.4 dbm GSM900 Loss=0.3+(31.9-31.5)=0.7 dbm DCS1800 loss=0.5+(28.8-28.4)=1.0 dbm 5.5 18 Initial Final test,19 RF Final Test, RF Final Test,, 20, OK.
19 20 21, PASS.
21 1 2 3 RF Final Test 5.6 Lacation update Fail = 101 MT Call Fail = 102 Call Drop = 103 Average Burst Power Fail = 104 Peak Burst Power Fail = 105 PVT Match Fail = 106 Timing Error Fail = 107 Phase Error Peak Fail = 108
Phase Error RMS Fail = 109 Frequency Error Fail = 110 Spectrum due to Modulation Fail = 111 Spectrum due to Switching Fail = 112 Rx Quality Fail = 113 Rx Level Fail = 114 BER Fail = 115 5.8 1. : 104 : MTK_atedemo.exe.13 TEST MODE SELET Calibration & GSM Test,MTK_atedemo.exe, Initial Cal& Final,, cal&final