L L WB T 附件 10 版本号 :FH-2016-002 风华高科 安全规格认证多层片式陶瓷电容器 Safety Recognized MLCC 一 特性 * 新型独石结构, 体积小, 电容量高, 能在高压下工作 * 符合 UL60950 标准 * 仅用于回流焊接 * 它们实用于薄型设备 应用范围 * 适合于无变压器的 DAA 调制调解器线路滤波器及耦合用 * 适合信息设备线路滤波器用 Features * A New monolithic structure capacitor for small,high-capacitance capability of operating at high-voltage levels. *Available for equipment base on UL60950-1. *Only for reflow soldering *Fit for use on thin type equipment. Application *Ideal for use on line filters and couplings for DAA modems without transformers. *Ideal for use on line filters for information equipment. 二 结构及尺寸 STRUCTURE AND DIMENSIONS 尺寸 DIMENSIONS W 英制表示 British expression WB 型号 Type 尺寸 Dimensions (mm) 公制表示 Metric expression L W T WB 1808 4520 4.50±0.40 2.00±0.20 2.50 0.60±0.30 1812 4532 4.50±0.40 3.20±0.30 3.50 0.60±0.30 2220 5750 5.70±0.40 5.00±0.40 3.50 0.60±0.30 2225 5763 5.70±0.50 6.30±0.50 3.50 0.60±0.30 备注 : 可根据客户的特殊要求设计符合客户需求的产品 Note:We can design according to customer special requirements. 第 1 页共 9 页
风华高科 三 型号规格表示方法 HOW TO ORDER SC 08 B 102 K 302 XA L 1 2 3 4 5 6 7 8 说明 NOTES: 1 SC 代表安规电容器 2 尺寸 DIMENSIONS 单位 (unit):inch/ mm 代号 08 12 20 25 尺寸规格 Size Code 1808 1812 2220 2225 长 宽 (L W)inch 0.18 0.08 0.18 0.12 0.22 0.20 0.22 0.25 长 宽 (L W)mm 4.50 2.00 4.50 3.20 5.70 5.00 5.70 6.30 3 介质种类 DIELECTRIC STYLE 介质种类 (Dielectric Code) CG B 介质材料 (Dielectric) COG 或 NPO X7R 4 标称容量 NOMINAL CAPACITANCE 表示方式实际值 (Express (Actual Value) Method) 102 10 10 2 222 22 10 2 位 (unit):pf 注 : 头两位数字为有效数字, 第三位数字为 0 的个数 ;R 为小数点 Note: the first two digits are significant; third digit denotes number of zeros; R=decimal point. 5 容量误差 CAPACITANCE TOLERANCE 代码 (Code) J K M 误差 (Tolerance) ±5.0% ±10.0% ±20% 6 工作电压 Rated Voltage *7 代号 Code : 工作电压 交流 250V 单位 (unit):v XA XB YB YC X1 安规电容器 X2 安规电容器 Y2 安规电容器 Y3 安规电容器 代号使用时的峰值脉冲电压 kv 耐久性试验前施加的峰值脉冲电压 kv XA XB 2.5kV<U 4.0kV 2.5kV C R 1.0μF, 4 C R >1.0μF,4/ C R C R 1.0μF, 2.5 C R >1.0μF,2.5/ 代号额定电压 V 耐久性试验前施加的峰值脉冲电压 kv YB 150V U 250V 5.0 YC 150V U 250V -- 第 2 页共 9 页 C R
风华高科 *8 厚度代号 : 代号厚度 L 1.6±0.2 M 1.8±0.2 N 2.0±0.2 O 2.5±0.2 P 2.8±0.2 Q 3.2±0.2 X 按照个别尺寸规格规定四 电容量范围 *XA 安规电容器 材料 COG X7R 代号 08 12 20 25 08 12 20 25 尺寸 1808 1812 2220 2225 1808 1812 2220 2225 电容量 2PF 5PF 6.8PF 8.2PF 10PF 15PF 22PF 33PF 47PF 56PF 68PF 82PF 100PF 120PF 150PF 180PF 220PF 270PF 330PF 470PF 560PF 820PF 1.0nF 1.5nF 2.2nF 3.3nF 4.7nF 第 3 页共 9 页
风华高科 四 电容量范围 材料 以最新版本的内容为准 *XB 安规电容器 代号 20 25 尺寸 2220 2225 电容量 10nF 15nF 22nF 33nF 47nF 56nF 82nF 100nF *YB YC 安规电容器 材料 COG X7R 代号 08 12 20 25 08 12 20 25 尺寸 1808 1812 2220 2225 1808 1812 2220 2225 电容量 2PF 5PF 6.8PF 8.2PF 10PF 15PF 22PF 33PF 47PF 56PF 68PF 82PF 100PF 120PF 150PF 180PF 220PF 270PF 330PF 470PF 560PF 820PF 1.0nF 1.5nF 2.2nF 3.3nF 4.7nF X7R 第 4 页共 9 页
风华高科 五 可靠性测试 Reliability Test 技术规格 Technical Specification 测试方法 Test Method and Remarks 容量 Capacitance Ⅰ 类 ClassⅠ Ⅱ 类 Class Ⅱ 应符合指定的误差级别 Should be within the specified tolerance. 应符合指定的误差级别 Should be within the specified tolerance. 测试频率 测试电压 标称容量 Measuring Measuring Capacitance Frequency Voltage 1000pF 1MHZ±10% 1.0± >1000 pf 1KHZ±10% 0.2Vrms 测试温度 : 25 ±3 测试频率 :1KHZ±10% 测试电压 :1.0±0.2Vrms Test Temprature:25 ±3 Test Frequency:1KHZ±10% Test Voltage:1.0±0.2Vrms DF 标称容量 Capacitance 测试频率 Measuring Frequency 测试电压 Measuring Voltage Ⅰ 类 0.56% Cr<5 pf 1MHZ±10% 损耗角正切 (DF, tanδ) Dissipation Factor ClassⅠ Ⅱ 类 1.5[(150/Cr)+7] 10-4 5pF Cr<50 pf 1MHZ±10% 0.15% 50pF Cr 1000 pf 1MHZ±10% 0.15% >1000 pf 1KHZ±10% 50V C 10µF 测试频率 :1KHZ±10% 1.0± 0.2Vrms Class X7R 测试电压 :1.0±0.2Vrms Ⅱ 2.5% Test Frequency:1KHZ±10% Test Voltage:1.0±0.2Vrms 第 5 页共 9 页
风华高科 技术规格 * 测试方法 Technical Specification Test Method and Remarks 绝缘电阻 Ⅰ 类 ClassⅠ C 10 nf, Ri 50000MΩ C>10 nf, Ri C R 500S 测试电压 :DC500±50V 测试时间 : 60±5 秒测试湿度 : 75% (IR) 测试温度 : 25 ±3 Insulati 测试充放电电流 : 50mA on Resistan ce Ⅱ 类 Class Ⅱ X7R C 25 nf, Ri 10000MΩ C>25 nf, Ri C R >100S Measuring Voltage: DC500±50V Duration: 60±5s Test Humidity: 75% Test Temprature: 25 ±3 Test Current: 50mA 在端子间施加表中的电压 60±1S 时不应观察 介质耐电强度 (DWV) Dielectr ic Withstan ding Voltage 无缺陷或异常 No defects or abnormalities 到任何故障, 并且充电 / 放电电流不超过 50mA No failure shoule be observed when voltage in the table is applied between the terminations for 60 sec.provided the charge/discharge current is less than 500mA. 测量电压 X 型 DC1075V Y 型 AC1500V 将电容在 80~120 的温度下预热 10~30 秒. Preheating conditions:80 to 120 ; 可焊性 Solderabili ty 上锡率应大于 95% 外观 : 无可见损伤. At least 95% of the terminal electrode is covered by new solder. Visual Appearance: No visible damage. 10~30s. 有铅焊料 :(Sn/Pb:63/37) 浸锡温度 : 235±5 浸锡时间 : 2±0.5s Solder Temperature: 235± 5 无铅焊料 : 浸锡温度 : 245±5 浸锡时间 : 2±0.5s Solder Temperature: 245 Duration: 2±0.5s ±5 Duration: 2±0.5
第 6 页共 9 页 风华高科 技术规格 Technical Specification 测试方法 Test Method and Remarks NPO 至 SL NPO to SL X7R 将电容在 100~200 的温度下预热 10±2 分钟. ±0.5% 或 ±0.5PF, 取较大值 浸锡温度 : 265±5 ΔC/C ±0.5% or ±0.5PF,whichever -5~+10% 浸锡时间 : 10±1s is larger 然后取出溶剂清洗干净, 在 10 倍以上的显 耐焊接热 Resistance to Soldering Heat 抗弯曲强度 Resistanc e to Flexure of 同初始标准 DF Same to initial value. 同初始标准 IR Same to initial value. 外观 : 无可见损伤上锡率 : 95% Appearance:No visible damage.at least 95% of the terminal electrode is covered by new solder. 外观 : 无可见损伤. Appearance: No visible damage. 微镜底下观察. 放置时间 :24±2 小时放置条件 : 室温 Preheating conditions: 100 to 200 ; 10±2min. Solder Temperature: 265±5 Duration: 10±1s Clean the capacitor with solvent and examine it with a 10X(min.) microscope. Recovery Time: 24±2h Recovery condition: Room temperature 试验基板 :Al 2 O 3 或 PCB 弯曲深度 :1mm 施压速度 :0.5mm/sec. 单位 :mm 应在弯曲状态下进行测量 T=10 Substrate (Bending Strength) 45±2 45±2 Test Board: Al 2 O 3 or PCB Warp: 1mm ΔC/C ±10% Speed: 0.5mm/sec. Unit: mm The measurement should be made with the board in the bending position.
第 7 页共 9 页 风华高科 端头结合强度 Termination Adhesion 温度循环 Temperature Cycle 技术规格 Technical Specification 外观无可见损伤 No visible damage. ΔC/C: Ⅰ 类 : ±1% 或 ±1pF, 取两者中最大者 Ⅱ 类 : B: ±10% ClassⅠ: ±1% or ±1pF, whichever is larger. ClassⅡ: B: ±10% 测试方法 Test Method and Remarks 施加的力 :5N 时间 :10±1S Applied Force: 5N Duration: 10±1S 预处理 (2 类 ): 上限类别温度,1 小时 恢复 :24±1h 初始测量 循环次数 :5 次, 一个循环分以下 4 步 : 阶段 温度 ( ) 时间 ( 分钟 ) 下限温度 第 1 步 30 (NPO/X7R:-55) 第 2 步 常温 (+20) 2~3 上限温度第 3 步 30 (NPO/X7R:+125) 第 4 步常温 (+20) 2~3 试验后放置 ( 恢复 ) 时间 :24±2h Preheating conditions: up-category temperature, 1h Recovery time: 24±1h Initial Measurement Cycling Times: 5 times, 1 cycle, 4 steps: Step Temperature( ) Time (min.) 1 Low- category temp. 30 (NPO/X7R:-55) 2 Normal temp. (+20) 2~3 3 Up- category temp. 30 (NPO/X7R:+125) 4 Normal temp. (+20) 2~3 Recovery time after test: 24±2h
第 8 页共 9 页 风华高科 潮湿试验 Moisture Resistanc e 寿命试验 Life Test 技术规格 Technical Specification Ⅰ 类 : ±2% 或 ±1pF, 取两者之中较大者 Δ Ⅱ 类 : B: ±10% C/C ClassⅠ: ±2% or ±1pF, whichever is larger. ClassⅡ: B: ±10% 2 倍初始标准 DF Not more than twice of initial value. Ⅰ 类 :Ri 2500MΩ 或 Ri C R 25S 取两者之中较小者. Class Ⅰ : Ri 2500M Ω 或 Ri C R 25S whichever is smaller. IR Ⅱ 类 :Ri 1000MΩ 或 Ri C R 25S 取两者之中较小者. Class Ⅱ : Ri 1000M Ω 或 Ri C R 25S whichever is smaller. 外观 : 无损伤 Appearance: No visible damage. Ⅰ 类 : ±2% 或 ±1pF 取两者之中较大者 Δ Ⅱ 类 :B: ±20% C/C ClassⅠ: ±2% or ±1pF, whichever is larger. ClassⅡ: B: ±20% 2 倍初始标准 DF Not more than twice of initial value. Ⅰ 类 :Ri 4000MΩ 或 Ri C R 40S 取两者之中较小者. Class Ⅰ : Ri 4000M Ω 或 Ri C R 40S whichever is smaller. IR Ⅱ 类 :Ri 2000MΩ 或 Ri C R 50S 取两者之中较小者. Class Ⅱ : Ri 2000M Ω 或 Ri C R 50S whichever is smaller. 外观 : 无损伤 Visual Appearance: No visible damage. 测试方法 Test Method and Remarks 温度 :40±2 湿度 :90~95%RH 时间 :500 小时放置条件 : 室温放置时间 :24 小时 (Ⅰ 类 );48 小时 (Ⅱ 类 ) Temperature:40±2 Humidity:90~95%RH Duration:500h Recovery conditions : Room temperature Recovery Time:24h (Class1) or 48h (Class2) 1.2 倍工作电压时间 :100 小时充电电流 : 不应超过 50mA 温度 :125 (NPO X7R) 放置条件 : 室温放置时间 :24 小时 (Ⅰ 类 ), 或 48 小时 (Ⅱ 类 ), 1.2 Multiple Duration: 100h Charge/ Discharge Current: 50mA max. Temperature:125 (NPO X7R); Recovery Conditions: Room Temperature Recovery Time: 24h (Class 1), or 48h (Class2)
第 9 页共 9 页