DRB1369F

Transcription

1

2 IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. IMPORTANTE La luz intermitente com el símbolo de punta de flecha dentro un triángulo equilátero. Está convenido para avisar el usuario de la presencia de voltaje peligrosa no aislada dentro el producto que podría constituir un peligro de choque eléctrico para las personas. WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture. D _A_En WARNING Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 23V or 2V) written on the rear panel. D _A_En VENTILATION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 5 cm at each side). WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D b_A_En WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment. D a_A_En Operating Environment Operating environment temperature and humidity: +5 ºC +35 ºC (+4 ºF +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D c_A_En 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATENCIÓN: PARA PREVENIR EL PELIGRO DE CHOQUE ELÉCTRICO NO REMOVER LA TAPA NI LAS PARTES DENTRO NO UTILIZADAS, LLAMAR UNA PERSONA CUALIFICADA The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D _En-A El punto exclamativo dentro un triángulo equilátero convenido para avisar el usuário de la presencia de importantes instruciones sobre el funcionamento y la manutención en la libreta que acompaña el aparato. D _Sp NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. D8---2_En CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. D8--3a_En Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user s right to operate the equipment. D8--2_En If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation). D a_A_En CAUTION The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D a_A_En POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. S2_En ADVERTENCIA Este aparato no es impermeable. Para evitar el riesgo de incendio y de descargas eléctricas, no ponga ningún recipiente lleno de líquido (como pueda ser un vaso o un florero) cerca del aparato ni lo exponga a goteo, salpicaduras, lluvia o humedad. D _A_Sp ADVERTENCIA Antes de enchufar el aparato a la corriente, lea la sección siguiente con mucha atención. La tensión de la red eléctrica es distinta según el país o región. Asegúrese de que la tensión de la alimentación de la localidad donde se proponga utilizar este aparato corresponda a la tensión necesaria (es decir, 23 V ó 2 V) indicada en el panel posterior. D _A_Sp ADVERTENCIA Para evitar el peligro de incendio, no ponga nada con fuego encendido (como pueda ser una vela) encima del aparato. D a_A_Sp PRECAUCIÓN PARA LA VENTILACIÓN Cuando instale este aparato, asegúrese de dejar espacio en torno al mismo para la ventilación con el fin de mejorar la disipación de calor (por lo menos 5 cm detrás, y 5 cm en cada lado). ADVERTENCIA Las ranuras y aberturas de la caja del aparato sirven para su ventilación para poder asegurar un funcionamiento fiable del aparato y para protegerlo contra sobrecalentamiento. Para evitar el peligro de incendio, las aberturas nunca deberán taparse ni cubrirse con nada (como por ejemplo, periódicos, manteles, cortinas) ni ponerse en funcionamiento el aparato sobre una alfombra gruesas o una cama. D b_A_Sp Entorno de funcionamiento Temperatura y humedad del entorno de funcionamiento C; menos del 85% de humedad relativa (rejillas de refrigeración no obstruidas) No instale este aparato en un lugar mal ventilado, ni en lugares expuestos a alta humedad o a la luz directa del sol (o de otra luz artificial potente). D c_A_Sp Si la clavija del cable de alimentación de CA de este aparato no se adapta a la toma de corriente de CA que usted desea utilizar, deberá cambiar la clavija por otra que se adapte apropiadamente. El reemplazo y montaje de una clavija del cable de alimentación de CA sólo deberá realizarlos personal de servicio técnico cualificado. Si se enchufa la clavija cortada a una toma de corriente de CA, puede causar fuertes descargas eléctricas. Asegúrese de que se tira de la forma apropiada después de haberla extraído. El aparato deberá desconectarse desenchufando la clavija de la alimentación de la toma de corriente cuando no se proponga utilizarlo durante mucho tiempo (por ejemplo, antes de irse de vacaciones). D a_A_Sp PRECAUCIÓN El interruptor de la alimentación POWER de este aparato no corta por completo toda la alimentación de la toma de corriente de CA. Puesto que el cable de alimentación hace las funciones de dispositivo de desconexión de la corriente para el aparato, para desconectar toda la alimentación del aparato deberá desenchufar el cable de la toma de corriente de CA. Por lo tanto, asegúrese de instalar el aparato de modo que el cable de alimentación pueda desenchufarse con facilidad de la toma de corriente de CA en caso de un accidente. Para evitar correr el peligro de incendio, el cable de alimentación también deberá desenchufarse de la toma de corriente de CA cuando no se tenga la intención de utilizarlo durante mucho tiempo seguido (por ejemplo, antes de irse de vacaciones). D a_A_Sp When using this product follow the instructions written on the underside of the unit, which concern rated voltage, etc. D _En Cuando emplee este producto, siga las instrucciones escritas en la parte inferior de la unidad, relacionadas con la tensión nominal, etc. D _Sp PRECAUCIONES CONCERNIENTES A LA MANIPULACIÓN DEL CABLE DE ALIMENTACIÓN Tome el cable de alimentación por la clavija. No extraiga la clavija tirando del cable. Nunca toque el cable de alimentación cuando sus manos estén mojadas, ya que esto podría causar cortocircuitos o descargas eléctricas. No coloque la unidad, algún mueble, etc., sobre el cable de alimentación. Asegúrese de no hacer nudos en el cable ni de unirlo a otros cables. Los cables de alimentación deberán ser dispuestos de tal forma que la probabilidad de que sean pisados sea mínima. Una cable de alimentación dañado podrá causar incendios o descargas eléctricas. Revise el cable de alimentación está dañado, solicite el reemplazo del mismo al centro de servicio autorizado PIONEER más cercano, o a su distribuidor. S2_Sp

3 Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same. K5 En FEATURES CONTENTS FEATURES... 3 CONFIRM ACCESSORIES... 3 QUICK OPERATION GUIDE USING BEAT EFFECTS [BPM MODE]... 4 USING BEAT EFFECTS [RHYTHM MODE]... 5 USING THE DIGITAL JOG BREAK... 6 USING JOG MEMORY PLAY... 6 English High-Fidelity Sound The high-fidelity design features a 24-bit A/D and D/A converter (96 khz sampling) and 32-bit DSP, allowing the addition of effects without lowering the original sound quality; a relay bypass function has also been adopted. 2 3-Band Beat Effector ) Beat effects [BPM mode] Equipped with the same automatic BPM counter/beat effector made popular by the EFX-5. Allows effect processing on single selected bands in synch with the track tempo (BPM), for greater expressive possibilities than with conventional all-band effecters. 2) Beat effects [RHYTHM mode] This industry-first rhythm effector lets you apply effects in synch with the rhythm you input yourself. With the expression of a far wider range of unique effects compared to previous beat effectors, you have the potential for a new level of DJ performance. 3 Digital Jog Break Function The Jog dial allows real-time control of effect sounds. Up to eight seconds of Jog function can be stored in memory for automated replay. Up to 49 effects can be demonstrated in combination with the beat effector. 4 MIDI IN/OUT Function External MIDI signals (control signals and timing clock signals) can be used to control the effector, and as a medium for using the effector to control a sequencer or other component. BEFORE USE CONNECTIONS... 7 Connection Panel... 7 Basic Connections... 8 EFFECTS... Beat Effects... Digital Jog Break... 2 Effect Parameters... 3 CONTROLS AND FUNCTIONS... 4 Control Panel... 4 OPERATIONS OPERATIONS... 7 Adjusting Input Level... 7 Adjusting Effect Output Level... 7 Selecting Signal Flow... 7 Selecting Foot Switch Operation... 7 Selecting the Level Meter Display... 7 Digital Link Function... 7 Bypass Function... 7 Beat Effects [BPM mode]... 8 Beat Effects [RYHTHM mode]... 9 Digital Jog Break... 2 Jog Memory... 2 MIDI SETTINGS MIDI SETTINGS... 2 Synchronizing an external sequencer to an audio signal, or using EFX- operation data to operate an external sequencer... 2 To synchronize beat effects to external sequencer, or use an external sequencer to operate the EFX MIDI Implementation Chart Control Change (CC) Table Program Change About Rhythm Effects Snapshot Digital Link Function A variety of functions can be performed by using the dedicated digital link cable to connect this unit to a Pioneer DJ mixer (DJM-) with digital link support. 6 Digital IN/OUT Equipped with digital IN/OUT connectors with 24-bit/96 khz sampling, allowing use in studio track creation and other applications where high sound quality is demanded. OTHER TROUBLESHOOTING SPECIFICATIONS BLOCK DIAGRAM... 8 CONFIRM ACCESSORIES Operating Instructions... Digital link cable... Power cord... 3

4 QUICK OPERATION GUIDE (/3) Adjusting the input level Input signals to the input connectors, and adjust the INPUT LEVEL dial. Adjusting effect output level Rotate the EFFECT OUT LEV. dial to adjust the effect output level. USING BEAT EFFECTS [BPM MODE] Changing the level meter display mode Each time the METER MODE button is pressed, the level meter display alternates as follows: INPUT, OUTPUT light: Input and output monaural display. INPUT, L, R light: Input stereo display. OUTPUT, L, R light: Output stereo display.. Select the BPM measurement mode. Press the BPM MODE button so that the button lights together with the desired mode indicator (AUTO/MIDI/TAP). 2. Select effect type. Press the DELAY, ECHO, PITCH ECHO, TRANS, FLANGER, FILTER or PHASER button and the pressed button starts to flash. 3. Select the sound range for the effect. Press the button of the frequency (LOW, MID, HI) you wish to affect by the beat effect and the corresponding indicator lights. 4. Select the beat with which the effect is to be synchronized. Press a beat select button (/8, /4, /2, 3/4, /, 2/, 4/ or 8/) to light the desired button. EFFECT TIME display BPM measurement mode indicators DEPTH dial Sets the parameter of each effect. RHYTHM TAP display BPM COUNTER 5. Apply an effect. Press the lever towards you (ON position) to start operation; release it and it returns to the center position (OFF position). In the center position (OFF position), the original sound is not affected. Press the lever away from you to lock it in position so that the beat effect is applied also when the lever is released. TIME/BPM dial Set the desired effect time as in step 4. Turn the TIME/BPM dial while holding down the TAP/SHIFT button to make the desired BPM setting. When also the BPM MODE button is held down, BPM can be set in. increments. TAP/SHIFT button BPM can be manually adjusted by adjusting the beat (quarter notes) and hitting this key two times or more. dial Adjusts the balance between the original sound and effects. CHARACTER dial Sets the parameter 2 of each effect. 4

5 QUICK OPERATION GUIDE (2/3) BYPASS button When the button is pressed (button indicator flashes), the signal entering the input connectors is output directly (without modification) to the output connectors. English SIGNAL FLOW switch Selects the order in which signals are passed through the electronic sections (from beat effect to digital jog break, or vice versa). USING BEAT EFFECTS [RHYTHM MODE]. Select the rhythm input mode. Press the RHYTHM MODE button so that the button indicator lights. 2. Select effect type. Press the DELAY, ECHO, PITCH ECHO, TRANS, FLANGER, FILTER or PHASER button and the pressed button starts to flash. 3. Select the sound range for the effect. Press the button of the frequency (LOW, MID, HI) you wish to affect by the rhythm effect and the corresponding indicator lights. 4. Set to REC mode. When the REC button is pressed, the BPM display indicates. If no rhythm has been input, the unit will automatically enter the REC mode in step. 5. Input the rhythm. Tap your finger on the TAP button to input the desired rhythm. As you input the rhythm, the rhythm will be calculated and displayed on the RHYTHM TAP display (up to 8 taps with tap interval of 2 seconds or less). 6. Select the overall rhythm time. The pressed beat select button will light, and the overall rhythm time will be set at the multiple corresponding to the pressed button. EFFECT TIME display BPM measurement mode indicators DEPTH dial Sets the parameter of each effect. RHYTHM TAP display BPM COUNTER 7. Apply an effect. Press the lever towards you (ON position) to start operation; release it and it returns to the center position (OFF position). In the center position (OFF position), the original sound is not affected. Press the lever away from you to lock it in position so that the rhythm effect is applied also when the lever is released. BPM MODE button When the BPM MODE button is pressed while in the rhythm mode, the mode changes to the beat effect BPM mode. dial Adjusts the balance between the original sound and effects. CHARACTER dial Sets the parameter 2 of each effect. 5

6 QUICK OPERATION GUIDE (3/3) USING THE DIGITAL JOG BREAK. Select the desired effect. Press the desired effect button, JET, WAH, PHASE SHIFTER, RING, ZIP, HUMANIZER or VOCODER to flash the corresponding button. DEPTH dial Sets the parameter of each effect. DIGITAL JOG BREAK METER Indicates the amount of control exercised by the Jog dial. 2. Apply the desired effect. Turn the Jog dial either while pressing the lever towards you or pressing it away from you (ON position). As the Jog dial is turned, parameters change gradually and the selected effect is applied. When the dial rotation is stopped, the parameter returns to normal. When the lever is pressed towards you, releasing it causes it to automatically return to the center (OFF position). HOLD button When this button is pressed so that the button indicator lights, effects produced with the Jog dial will continue even when your hand is removed from the dial. USING JOG MEMORY PLAY. Hold the Jog memory button (M) depressed while rotating the Jog dial. Effect changes produced with the Jog dial will be stored in memory (maximum 8 seconds). When storage is completed, the SINGLE and LOOP buttons light. dial Adjusts the balance between the original sound and effects. 2. Press the SINGLE button or LOOP button When the SINGLE button is pressed, the stored Jog-dial effect change will be replayed one time only. When the LOOP button is pressed, the stored Jog-dial effect change will be replayed repeatedly. Press the button once more to stop the effect. CHARACTER dial Sets the parameter 2 of each effect. 6

7 BEFORE USE (CONNECTIONS) CONNECTIONS Connection Panel English Power input socket (AC IN) Use the provided power cord to connect this socket to an AC outlet. 2 POWER switch 3 Digital OUTPUT fs SELECT switch Use to change the digital output frequency sampling rate (fs) (44.kHz/48kHz/96kHz). 4 Link input/output connector (EFX LINK) When the accessory digital link cable is used to connect this connector to the DJ-mixer DJM- (with digital link support), digital link functions can be used, permitting a variety of new functions. CAUTION: The EFX LINK connector is designed to be connected via the provided digital link cable ONLY to a component equipped with the designated digital link function. The unit may be damaged if this connector is mistakenly connected to any other component. 5. MIDI input/output connectors (MIDI OUT, MIDI IN) Use to connect the effector to a MIDI component (see page 2). 6 Digital input/output connectors (DIGITAL IN, DIGITAL OUT) Use to connect the effector to a component provided with coaxial digital input/output connectors. 7 Foot switch jack (FOOT SW) Can be connected to a ON/OFF type foot switch with 6.3mm phone plug to allow ON/OFF control of effects. Foot switches are available in several types, including press-on, press-off, and latching-type ON/OFF. 8 Input/output gain select switch (IN&OUT LEVEL) Use to select the input/output gain ( db / +4dB). 9 Audio INPUT/OUTPUT jacks Uses 6.3mm phones plug. For monaural inputs, connect L input channel only for output on both L and R channels. Audio inputs are throughput (output) even when the unit s power is turned OFF. Audio INPUT/OUTPUT jacks INPUT/OUTPUT connectors using RCA pin jacks. Audio inputs are throughput (output) even when the unit s power is turned OFF. 7 Before making or changing the connections, switch off the power switch and disconnect the power cord from the AC outlet. This precaution should also be taken when changing the IN & OUT LEVEL switch and DIGITAL fs SELECT switch. When connections are made to the phone jack inputs and a monaural signal cable is connected to the L (MONO) terminal, inputs can be made to both the L and R channels. After all other connections are made, connect the power cord to a household wall outlet or to the auxiliary AC power takeoff on your amplifier. See page 2 for instructions on how to use the MIDI terminals. CAUTION: Do not make any connections that may create signal loops as this will cause circuit oscillations which could damage the speakers. [Example of connections that must not be performed] Do not connect the output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the same mixer. Do not connect the SEND output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the DJ Mixer (except for the RETURN terminal). Installation Location Avoid mounting on top of amplifiers, near spotlights, or other heat-emitting components and appliances; extended exposure to heat can cause damage to the effector itself. Install this unit as far as possible away from tuners and TV sets. A unit installed in close proximity to such equipment may cause noise or degradation of the picture. Cleaning the unit To clean the unit wipe with a polishing or a soft, dry cloth. For stubborn dirt, moisten a soft cloth with a weak solution of neutral detergent (diluted in five to six parts water), wring the cloth well, and wipe away the dirt. Use a dry cloth to wipe the surface dry. Do not use volatile liquids such as benzene or thinner which will damage to the unit. 7

8 26 +6 BEFORE USE (CONNECTIONS) Basic Connections Before making or changing the connections, switch off the power switch and disconnect the power cord from the AC outlet.. Connecting the SEND/RETURN Terminals on the DJ Mixer (on DJ mixer provided with SEND and RETURN terminals) Make connections using cables with /4-inch/6.3 mm in diameter phone plugs. Set the DJ mixer so that the SEND and RETURN terminals can be used. If the DJ mixer supports digital link, it can be connected to the EFX LINK connector using the provided digital link cable to eliminate the need for connection by an analog 6.3mm phone plug cable (audio signals transmitted over the digital link cable are in digital format). Also note that extraneous noise may result if both analog and digital link cables are connected simultaneously. Effector EFX- Set the IN & OUT LEVEL switch on the Effector to the [ db] position. Stereo Amplifier FOOT SW OUTPUT INPUT EFX LINK Foot switch (pedal switch) Accessory digital link cable : Signal flow MASTER OUT DJ Mixer SEND SEND RETURN RETURN DJ CD Player CH- CH-2 DJ CD Player 2. Connecting a DJ Mixer and an Audio Amplifier (on DJ mixer not provided with SEND and RETURN terminals) Connect using cables with phone plugs (/4-inch/6.3 mm in diameter) or RCA pin plugs. 8 When making connections, do not connect both RCA pin plug cables and phones plug cables for the same connection function (use either one or the other, not both). Also, if you wish to use analog connections, do not also make connections to the digital connectors (digital signals are given priority when connected). For digital connections, use RCA pin-plug coaxial cables. Set the OUTPUT fs SELECT switch in accordance with the connected component.

9 BEFORE USE (CONNECTIONS) OUTPUT L Set the IN & OUT LEVEL switch on the Effector to the [+4 db] position. R L MASTER OUT L English R INPUT R Effector EFX- INPUT L R MASTER OUT Stereo Amplifier DIGITAL OUT DJ Mixer 3. Connecting a DJ CD Player and a DJ Mixer (this connection applies effects only to the sound of the DJ CD player on channel 2) Connect the units using a cable with RCA pin plugs. For digital connections, use RCA pin-plug coaxial cables. Effector EFX- Set the IN & OUT LEVEL switch on the Effector to the [ db] position. AUDIO OUT L L R INPUT R DIGITAL OUT DIGITAL IN L R OUTPUT DIGITAL IN DIGITAL IN L R DIGITAL OUT DIGITAL OUT DJ Mixer 4. Connecting the power cord After all other connections are completed, insert the power cord s plug into a wall power outlet or the auxiliary power outlet of an amplifier. DJ CD Player CAUTION: Signal inputs are handled in a specific order of priority: EFX LINK > digital inputs > analog inputs When EFX LINK signals are input, digital signals are not output. 9

10 EFFECTS (Beat Effects) EFFECTS Beat Effects. DELAY effect Adds delay sound to the original sound. [BPM mode] A delay sound is added to the original sound at the value set with the TIME dial. The DEPTH dial can be used to adjust the feedback level. Feedback means to input the delay sound back into the delay input. This control allows the amount of the feedback to be adjusted (near the [MAX] setting, the sound level rises). The CHARACTER dial can be used to adjust the amount of filter applied to the feedback sound. The dial can be used to adjust the levels of the original and delay sounds. Sound level TIME Original sound Delay sound Feedback DEPTH Time 2. ECHO effect Adds delay sound to the original sound. [BPM mode] A delay sound is added to the original sound at the value set with the TIME dial. [RHYTHM mode] Adds TAP delay sound to the original sound (Max 8-TAP). Difference from the DELAY effect: Even if the BEAT EFFECTS lever switch is moved from [ON] to [OFF], the feedback sound or TAP delay sound will continue. In the BPM mode, if the DEPTH dial is set to [MAX] and the BEAT EFFECTS lever switch is moved from [ON] to [OFF], a hold-delay effect will be produced without attenuating the feedback sound (near the [MAX] setting, the sound level rises). In the RHYTHM mode, when the switch is turned [OFF] the effect will end with the final TAP delay sound for the original sound. BPM mode [RHYTHM mode] Changes the pitch of the TAP delay sound, and applies the effect to the original sound. Although a maximum of 8-TAPs can be recorded, only 4-TAPs can be used for effect. The DEPTH dial can be used to adjust the TAP delay level (near the [MAX] setting the sound volume will rise somewhat). The CHARACTER dial can be used to adjust the pitch of the TAP delay sound. The dial can be used to adjust the levels of the original and pitch echo sounds. TAP pitch echo block. TAP 2 pitch echo block. TAP 3 pitch echo block. TAP 4 pitch echo block. Delay block [RHYTHM mode] A delay sound set with the TAP button (TAP delay sound) is added to the original sound (Max 8-TAP). The DEPTH dial can be used to adjust the TAP delay level (near the [MAX] setting the sound volume will rise). The CHARACTER dial can be used to adjust the amount of filter applied to the TAP delay sound. The dial can be used to adjust the levels of the original and TAP delay sounds. Sound level Original sound Delay sound TAP delay block TAP 8 delay block Delay Delay sound sound Delay sound DEPTH Time RHYTHM mode Echo block TAP echo block TAP 8 echo block 3. PITCH ECHO effect Changes the pitch of the delay sound, and applies the effect to the original sound. In the same way as for the ECHO effect, the effect sound is maintained even if the BEAT EFFECTS lever switch is set from [ON] to [OFF]. [BPM mode] Changes the pitch of the delay sound set with the TIME dial, and applies the effect to the original sound. The DEPTH dial can be used to adjust the feedback level. The CHARACTER dial can be used to adjust the pitch of the delay sound. The dial can be used to adjust the levels of the original and pitch echo sounds. Pitch echo block 4. TRANS effect Cuts the original sound intermittently. [BPM mode] Cuts the sound at the interval set by the TIME dial (cuts latter half of the interval). The DEPTH dial can be used to adjust the amount that is cut. Cut Cut Time Time Time The CHARACTER dial can be used to adjust the phase difference between L and R channels. Time Time Time Time The dial can be used to adjust the levels of the original and trans sounds.

11 EFFECTS (Beat Effects) [RHYTHM mode] Cuts the original sound in synch with the TAP rhythm (Max 8-TAP). The DEPTH dial can be used to adjust the amount that is cut. The CHARACTER dial can be used to adjust of phase difference between L and R channels. The dial can be used to adjust the levels of the original and trans sounds. 5. FLANGER effect By applying a time-shifted sound to the original, the effect of an ascending or descending jet plane (flange effect) is produced. [BPM mode] Changes the frequency range to which the flange effect is applied at the interval set by the TIME dial. The DEPTH dial can be used to adjust the strength of the flange effect by changing the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the cyclic changes in the flange effect. The dial can be used to adjust the levels of the original and flanger sounds. Flange effect change Flange effect change Flange effect change Time Time Time [RHYTHM mode] Changes the frequency subjected to flange effect, in synch with the TAP rhythm (Max 8-TAP). The DEPTH dial can be used to adjust the strength of the flange effect by changing the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the cyclic changes in the flange effect. The dial can be used to adjust the levels of the original and flanger sounds. 6. FILTER effect A low-pass filter is applied to the original sound to produce more muted sound. [BPM mode] The cutoff frequency of the low-pass filter changes with the cycle set by the TIME dial. The DEPTH dial is used to change the unique coloring of the sound by adjusting the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to vary the cutoff frequency of the cyclic low-pass filter. The dial can be used to adjust the levels of the original and filter sounds. [RHYTHM mode] Changes cutoff frequency of the low-pass filter, in synch with the TAP rhythm (Max 8- TAP). The DEPTH dial is used to change the unique coloring of the sound by adjusting the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to vary the cutoff frequency of the cyclic low-pass filter. The dial can be used to adjust the levels of the original and filter sounds. 7. PHASER effect Causes a phase effect by applying a phaseshifted sound to the original sound. [BPM mode] Changes the frequency range to which the phase effect is applied at the interval set by the TIME dial. The DEPTH dial can be used to adjust the strength of the phase effect by changing the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the cyclic changes in the phase effect. The dial can be used to adjust the levels of the original and phaser sounds. Phase effect change Phase effect change Phase effect change Time Time Time [RHYTHM mode] Changes the frequency subjected to phase effect, in sync with the TAP rhythm (Max 8- TAP). The DEPTH dial can be used to adjust the strength of the phase effect by changing the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the cyclic changes in the phase effect. The dial can be used to adjust the levels of the original and phaser sounds. English

12 EFFECTS (Digital Jog Break) Digital Jog Break. JET effect A time-shifted sound is applied to the original, thus producing the effect of a jet airplane ascending or descending (flange effect). The Jog dial is used to change the frequency range that is affected by the flange effect. REV Jog dial The amount of resonance is changed using the DEPTH dial to emphasize the flange effect. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the reverb effect. Jet block Flange effect change Reverb block FWD The dial can be used to adjust the levels of the jet + reverb sound and original sound. 2. WAH effect The filter s cutoff frequency is shifted, causing great change in the sound tone. The Jog dial is used to vary the filter s cutoff frequency. 3. PHASE SHIFTER effect A phase-shifted sound is added to the original, thus producing a phase shifter effect. The Jog dial is used to change the frequency range that is affected by the phase effect. REV The amount of resonance is changed using the DEPTH dial to emphasize the phase effect. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the reverb effect. Phase shifter block Phase effect change Jog dial Reverb block FWD The dial can be used to adjust the levels of the phase shifter + reverb sound and the original sound. 4. RING modulator effect By modulating the original sound in the shape of a sine wave, the resulting sound coloration resembles a ringing bell. The Jog dial is used to vary the sine wave frequency. The DEPTH dial can be used to adjust the Jog dial s variable range (step). REV Jog dial The CHARACTER dial can be used to adjust the reverb effect Zip block The dial can be used to adjust the levels of the zip+reverb and original sounds. 6. HUMANIZER effect The original sound is modified to resemble the vowel sounds of the human voice. The Jog dial is used to vary the vowel sound coloration. REV Reverb block FWD FWD Jog dial The DEPTH dial is used to change the unique coloring of vowel sounds by adjusting the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the reverb effect. Jog dial Frequency REV FWD Humanizer block Reverb block Jog dial The DEPTH dial is used to change the unique coloring of the sound by adjusting the amount of resonance. (When approaching the [MAX] setting, the level of the sound increases.) The CHARACTER dial can be used to adjust the reverb effect. Wah block The dial can be used to adjust the levels of the wah + reverb sound and the original sound. 2 Reverb block Frequency Frequency Frequency Frequency Jog dial The DEPTH dial can be used to adjust the amplitude of the sine wave. The CHARACTER dial can be used to adjust the reverb effect. Ring block Reverb block The dial can be used to adjust the levels of the ring + reverb and original sounds. 5. ZIP effect The Jog dial is used to change the pitch. Up (about octave) Pitch Original sound Down (about 5 octaves) REV Jog dial FWD The dial can be used to adjust the levels of the humanizer + reverb and the original sounds. 7. VOCODER effect The input sound is replaced by an internally generated signal sound, producing a mechanical sound effect. The Jog dial is used to change the frequency of the internally generated signal sound. The DEPTH dial can be used to vary the internally generated sound from the basic sound to a chord. (The sound more nearly approximates the chord as the adjustment approaches the [MAX] setting.) The CHARACTER dial can be used to change chords codes. Selectable codes include Minor (MIN), Minor7, 7, Major (center position), Major7, Sus4, and Add9 (MAX). Vocoder block The dial can be used to adjust the levels of the vocoder and original sounds.

13 EFFECTS (Effect Parameters) Effect Parameters Beat effect DELAY ECHO PITCH ECHO TRANS FLANGER FILTER PHASER BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE BPM MODE RHYTHM MODE Parameter (TIME) ~6 [ms] ~6 [ms]* ~6 [ms] ~6 [ms]* ~6 [ms] ~6 [ms]* ~6 [ms] ~6 [ms]* ~32 [ms] ~32 [ms]* ~32 [ms] ~32 [ms]* ~32 [ms] ~32 [ms]* Parameter (DEPTH) Feedback (feedback level) TAP gain (TAP delay level) Feedback (feedback level) TAP gain (TAP delay level) Feedback (feedback level) TAP gain (TAP delay level) Sound cutoff (amount removed) Sound cutoff (amount removed) Resonance Resonance Resonance Resonance Resonance Resonance Parameter 2 (CHARACTER) Feedback filter (Amount of feedback filter) TAP filter (Amount of TAP delay filter) Feedback filter (Amount of feedback filter) TAP filter (Amount of TAP delay filter) Pitch (delay sound pitch) TAP Pitch (TAP delay sound pitch) Phase (L/R-ch phase difference) Phase (L/R-ch phase difference) LFO pattern (change cyclic effect) LFO pattern (change cyclic effect) LFO pattern (change cyclic effect) LFO pattern (change cyclic effect) LFO pattern (change cyclic effect) LFO pattern (change cyclic effect) Parameter 3 () Comments Max 8-TAP Max 8-TAP Max 4-TAP Max 8-TAP Max 8-TAP Max 8-TAP Max 8-TAP * The effect time display in the rhythm mode shows the total time from the beginning to end of TAP input. For this reason, the noted MIN time may be somewhat different from the effect time display. English Digital Jog Break Parameter (JOG) Parameter (DEPTH) Parameter 2 (CHARACTER) Parameter 3 () Comments JET Delay time (amount of delay) Resonance Reverb (reverberation effect) WAH Frequency (filter frequency) Resonance Reverb (reverberation effect) PHASE SHIFTER Frequency (filter coefficient) Resonance Reverb (reverberation effect) RING Frequency (sine wave frequency) Amplitude (sine-wave amplitude) Reverb (reverberation effect) ZIP Pitch (Scale) Step (ScaleÔLinear) Reverb (reverberation effect) HUMANIZER Vowel (vowel sound) Resonance Reverb (reverberation effect) VOCODER Oscillator frequency (internally generated sound frequency) Chord (chord ratio) Chord 3

14 BEFORE USE (CONTROLS AND FUNCTIONS) CONTROLS AND FUNCTIONS Control Panel INPUT LEVEL dial Use to adjust the input level. Adjustment range is to +9dB with analog inputs, and to db with digital inputs. 2 SIGNAL FLOW switch Use to select the order of signal flow between beat effect and digital jog break sections. JOG = BEAT: Signals travel through the digital jog break section before passing to the beat effect section. BEAT = JOG: Signals travel through the beat effect section before passing to the digital jog break section. 3 Foot switch mode selector (FOOT SW) Use to select which function is controlled (ON/OFF) by an attached foot switch (pedal switch). BEAT: Attached foot switch controls beat effect function (ON/OFF). JOG: Attached foot switch controls digital jog break function (ON/OFF). BOTH: Attached foot switch controls both beat effect function and digital jog break function (ON/OFF). 4 MIDI mode select switch Select MIDI communication between computer and other instruments, etc. TRANSMIT: Acts as MIDI controller RECEIVE: Effector can be controlled by MIDI signals. OFF: Acts as effector (communication OFF) 5 METER MODE/MIDI SNAP button [Use to switch the function of the level meter display.] Each time the button is pressed, the level meter display switches between input and output monaural display, input stereo display, and output stereo display. [MIDI Snapshot Mode] When this button is held depressed with the MIDI mode set to [TRANSMIT], a snapshot will be sent to the external MIDI component. 6 Level meter mode display (INPUT, OUTPUT, L, R) Input and output monaural display: Both [INPUT] and [OUTPUT] indicators light. Input stereo display: [INPUT] and [L], [R] indicators light. Output stereo display: [OUTPUT] and [L], [R] indicators light. 7 Level meter display 8 MIDI START/CH SET button / indicator [MIDI START] If this button is pressed when MIDI mode is set to [TRANSMIT], the MIDI start/stop signal is output. Lights steadily with START, and goes out with STOP. [MIDI channel setting (CH SET)] If this button is held depressed when MIDI mode is set to [TRANSMIT] or [RECEIVE], the MIDI indicator flashes and the MIDI setting mode is enabled. 4

15 BEFORE USE (CONTROLS AND FUNCTIONS) 9 BYPASS button / indicator When this button is set to ON, the audio input connector signals are fed directly to the output connectors, bypassing the effector circuits. When the audio input/output connectors are connected directly in this way, the indicator flashes. EFFECT OUT LEV. dial When effects are set to ON, this dial can be used to control the effect output level. Adjustment range is to +6dB. Beat Effect section BPM COUNTER display Displays the beats-per-minute of the input source, or the TAP input. The indicator flashes during automatic BPM calculation. When power is first turned on, the counter will flash [2 BPM]. 2 EFFECT TIME display Displays actual effect time. When power is first turned on, defaults to [5 msec]. 3 BPM measurement mode display (AUTO, MIDI, TAP). Displays the BPM measurement mode. 2 Beat select buttons / indicators (/8, /4, /2, 3/4, /, 2/, 4/, 8/) [During BPM mode] When a BPM is measured automatically or input manually, the beat select button [/] is selected by default. The effect is synchronized automatically to the BPM, and the corresponding effect time is displayed. If a beat select button is then pressed, the effect is newly synchronized to the corresponding multiple of the BPM (/ 8, /4, /2, 3/4, etc.), thus allowing one-touch change of the BPM synchronization multiple. In turn, the selected beat select button lights, thus showing to what multiple of the actual BPM the effect is synchronized, as well as the multiple of the time parameter. [During RHYTHM mode] When the rhythm input with the TAP button is established, [/] is selected and a multiple of the rhythm can be selected with the beat select buttons. 2 Beat effect beat-interval indicators The indicators light to show the period of the effect time. 22 Beat effect TIME/BPM dial When rotated the effect time selected with the beat select buttons can be changed as desired. If the dial is rotated while depressing the TAP button, the BPM can be set as desired (BPM manual input). English 4 MIDI display Lights when handling MIDI data. 5 RHYTHM TAP display Displays the tap count input in the rhythm mode. 6 Beat effect select button / indicator (DELAY, ECHO, PITCH ECHO, TRANS, FLANGER, FILTER, PHASER). Use to select the beat effect. All buttons light, and selected effect button flashes. When power is turned ON, DELAY flashes. 7 BEAT EFFECTS indicator Lights when beat effects are ON. 8 BEAT EFFECTS lever switch (OFF/ON/ON-LOCK) Pull the lever toward you [ON] to output beat-effected sounds. In the middle position beat effects are [OFF]; push the lever away from you to lock the lever in the [ON/LOCK] position (effects are locked ON). When pulled to the [ON] position, beat effects are output only while the lever is held; when your finger is released, the lever returns to middle [OFF] position. 9 EFFECT FREQUENCY select buttons (LOW/MID/HI) Use to select the frequency band of the sounds to which beat effects will be applied. The button of the selected band will light. When power is first turned ON, all three of the ranges LOW, MID, and HI are selected. If all three range buttons are OFF, no beat effects will be applied to sounds. 23 BPM MODE button / indicator Use to turn BPM mode ON, and to select tempo measurement mode (AUTO/MIDI/TAP). During BPM mode, the button lights. If the TAP button is pressed (tapped) during BPM mode, the mode switches to manual BPM measurement mode. When power is first turned, the mode defaults to AUTO measurement mode. 24 TAP/SHIFT button / indicator [During BPM mode] When this button is tapped, the BPM manual measurement mode is selected, and the interval between two taps (maximum interval 2 seconds) is measured; the corresponding EFFECT TIME and BPM count is displayed, and the beat select button [/] is selected. If the TIME/BPM dial is rotated while pressing this button, the BPM can be adjusted to an optional value (BPM manual input). [During RHYTHM mode] When this button is tapped, the rhythm is input (maximum tap interval 2 seconds, up to maximum rhythm count 8). The beat select button [/] is selected. [Tap indicator] Lights during normal use; goes out only when TAP is pressed. 25 Rhythm REC button Clears the currently input rhythm and allows input of a new rhythm. 5

16 BEFORE USE (CONTROLS AND FUNCTIONS) 26 RHYTHM MODE button / indicator When this button is pressed, the RHYTHM mode is selected, and the button lights. 27 Beat effect DEPTH dial Allows adjustment of effect feedback and timing parameters in accordance with the amount of rotation (see page 3). 28 Beat effect CHARACTER dial Allows adjustment of parameters other than those set with the beat effect DEPTH dial (see page 3). 29 Beat effect dial Rotate to adjust the mixing balance of original and effect sounds. When rotated fully to the [ORIGINAL] side, the original (un-effected) sound will be output; as the dial is rotated toward the [EFFECT] side, the effect sound is amplified and the original sound decreases. Digital Jog Break section 3 Digital jog break effect dial Rotate to adjust the mixing balance of original and effect sounds. When rotated fully to the [ORIGINAL] side, the original (un-effected) sound will be output; as the dial is rotated toward the [EFFECT] side, the effect sound is amplified and the original sound decreases. 3 Digital jog break effect CHARACTER dial Allows adjustment of parameters other than those set with the digital jog break DEPTH dial (see page 3). 32 Digital jog break DEPTH dial Allows adjustment of effect feedback and timing parameters in accordance with the amount of rotation (see page 3). 33 Jog dial Effect parameters change in response to the rotation of the dial. 36 Jog memory LOOP play button / indicator If the button is pressed while the button indicator is lighted, the parameter change previously recorded in memory in response to the Jog dial movement is reproduced (played back repeatedly). Press again to end Jog memory loop play. Indicator lights when the jog operation is stored in memory. Indicator flashes during jog memory loop play (playback). 37 Jog HOLD button / indicator When this button is pressed so that its indicator lights, the effect produced when rotating the Jog dial is maintained even if you remove your hand from the dial (when the hold function is OFF, the effect returns to normal if your hand is removed from the dial). When power is first turned on, the button defaults to jog hold OFF (indicator is off). 38 DIGITAL JOG BREAK effect lever switch (OFF/ON/ON-LOCK) Pull the lever toward you [ON] to output effected sounds. In the middle position effects are [OFF]; push the lever away from you to lock the lever in the [ON/LOCK] position (effects are locked ON). When pulled to the [ON] position, effects are output only while the lever is held; when your finger is released, the lever returns to middle [OFF] position. 39 DIGITAL JOG BREAK effect indicator Lights when digital jog break effect is ON. 4 Digital jog break effect selector buttons / indicators (JET, WAH, PHASE SHIFTER, RING, ZIP, HUMANIZER, VOCODER) Press to select a desired digital jog break effect. All the buttons light, and the select effect button flashes. When power is turned ON, JET flashes. 4 DIGITAL JOG BREAK METER During operation of the Jog dial, and during jog memory play, this meter lights to display the corresponding movement. 34 Jog memory button (M) If the Jog dial is rotated while holding this button depressed, the parameter change in response to the movement is recorded to memory, to a maximum 8 seconds. Recording to memory is not possible during jog memory play. 35 Jog memory SINGLE play button / indicator If the button is pressed while the button indicator is lighted, the parameter change previously recorded in memory in response to the Jog dial movement is reproduced (played back) one time only. Indicator lights when the jog operation is stored in memory. Indicator flashes during jog memory single play (playback). 6

17 OPERATIONS OPERATIONS INPUT LEVEL FOOT SW MIDI (TRANSMIT/RECEIVE/OFF) EFFECT OUT LEV. English SIGNAL FLOW METER MODE BYPASS Adjusting Input Level Adjust the input level so that the sound is not distorted due to an excessive input level. 7 Input signals to the input connectors, and rotate the INPUT LEVEL dial to adjust the level. Use the METER MODE button to select input stereo display (INPUT, L, R indicators light). If the proper adjustment cannot be obtained without rotating the INPUT LEVEL dial to its extreme [MIN] or [MAX] positions, try changing the position of the rear-panel IN&OUT LEVEL switch ( db / +4dB). Adjusting Effect Output Level Adjusts the sound level of the effect applied to the input sound signal by the beat effect and the digital jog break. 7 Input signals to the input connectors, and rotate the EFFECT OUT LEV. dial to adjust the effect output level. Use the METER MODE button to select output stereo display (OUTPUT, L, R indicators light). When both the BEAT EFFECTS lever switch and the DIGITAL JOG BREAK lever switch are set to [OFF], the output level is not changed by turning the EFFECT OUT LEV. dial. Selecting Signal Flow Select the order in which signal processing occurs (beat effect or digital jog break) 7 Use the SIGNAL FLOW switch to select the signal processing order: When set to the [JOG=BEAT] position, signals are processed for digital jog break effects first, followed by beat effects. When set to the [BEAT=JOG] position, signals are processed for beat effects first, followed by digital jog break effects. Selecting Foot Switch Operation This effector allows connection of an optional foot switch (pedal switch) for ON/OFF control of beat effects and digital jog break effects. Use the foot switch to select the way in which the foot switch operates. 7 Set the FOOT SW switch to the desired operating position: When set to the [JOG] position, the foot switch operates to turn digital jog break effects ON/OFF. When set to the [BOTH] position, the foot switch operates to turn both digital jog break effects and beat effects ON/OFF. When set to the [BEAT] position the foot switch operates to turn beat effects ON/OFF. * Use a commercially available switching-type foot switch with 6.3 mm monaural phone plug. Selecting the Level Meter Display This unit s level meter can be set to display the desired mode. 7 Press the METER MODE button to select the desired mode. Each time the METER MODE button is pressed, the display switches alternately as follows: [INPUT] and [OUTPUT] light: = Input and output level are displayed in monaural. [INPUT] and [L], [R] light: = Input level is displayed in stereo. [OUTPUT] and [L], [R] light: = Output level is displayed in stereo. Digital Link Function Fader Effect Function When the accessory digital link cable is used to connect this unit to a DJ mixer (DJM-) with digital link support, send/return connections are completed by a single digital connection, thus enabling fader effect functions that allow the DJ mixer s fader to be used to perform digital jog break. Bypass Function This function allows signals to be output directly, without passing through the effects processing circuitry. 7 Press the BYPASS button to make a direct link between input and output. When the BYPASS button is pressed, the button flashes and input signals are output directly, without passing through the effector circuitry. When the BYPASS button is flashed, the unit s controls will have no effect on the input signals. 7