D5说明书-11

Size: px

Start display at page:

Download "D5说明书-11"

玲鲁
4 years ago
Views:

1 高解析音频解码器使用说明书深圳市大号科技有限公司

2 安全注意事项请将本音响系统安装在通风良好阴凉干燥干净的位置远离直射阳光热源振动灰尘潮湿或寒冷只能使用本机指定的电压使用高于指定数值的电压很危险而且可能导致火灾损坏本机或造成人身伤害对于使用高于指定电压造成的任何损害深圳市大号科技有限公司将不负任何责任不要试图自行改造或修理本机如果需要任何服务请就近与有资格的深圳市大号科技有限公司维修人员联系不管有任何理由都没有打开机壳的必要如果打算长时间不使用本机比如度假时请从墙壁交流电源插座上断开电源线的连接保修条款一服务期限深圳市大号科技有限公司承诺产品的良好品质产品自售出之后7天内正常使用情况下出现故障客户可以选择退货或者保修不影响二次销售才可退货正常使用一年内出现故障可以免费保修二购买日期以销售商开出的购机发票或收据日期为准多购可以交易截图为准三有以下情况都不能享受三包服务.一切人为因素损坏包括非正常工作环境下使用或不按照说明书使用.用户私自拆机改装维修.使用非指定或许可的配件造成损坏的.机身的QC或保修贴损毁 5.不能出示有效购机凭证 6.不属于本公司产品四保修方式为送修此条款只适于中国大陆其它地区请参考当地销售代理商的规定和国家法规

3 特点使用美国ESS公司高端ES908PRO D/A芯片搭配使用ES9,ESS高性能DAC专用电源芯片,电源噪声低至uVrms,将 ES908PRO的性能推到极限 USB使用XMOS XU-08 真正的bit USB方案支持DoP和原生DSD PCM最高支持到768kHz DSD支持到DS 使用了超低相噪的晶振,并且使用了高速的CPLD进行时钟处理,以达到超低的时钟抖动全部输入口均支持DSD传输,同轴,光纤支持DoP6 分立元件大功率超大电流驱动耳放电路提供更大的耳机推力内置高效率低漏磁的环形的变压器为解码器提供充足且低噪声的电源供应特别设计的分立元件线性稳压电源和多个低噪声稳压电源为模拟电路提供低噪声电源使用颗高端双运放OPA6及大量发烧元器件日本音频协会(JAS)Hi-Res认证

4 技术参数输入方式...USB / 光纤 / 同轴 / IS 输出方式...平衡耳放 / 单端耳放 / 单端线路 /平衡线路 THD+N... 前级输出 0.000% 耳放输出 0.00% 动态范围...平衡线路 7dB 单端线路 db 信噪比... 前级输出 0dB 耳放输出 0dB USB传输方式...异步传输 USB兼容性...Windows 7 / 8 / 8. / 0, Mac OSX0.6以上 Linux 位深...USB bit 6 ~ bit 光纤同轴 bit 6 ~ bit 采样率...USB/IS PCM. ~ 768kHz DSD.8 ~.579MHz 光纤/同轴 PCM. ~ 9kHz DSD DSD6(DoP) 耳放输出功率...平衡 9mW(Ω) 05mW(6Ω) 55mW(50Ω) mw(00ω) 单端 80mW(Ω) 65mW(6Ω) 5mW(50Ω) 58mW(00Ω) 消耗功率...8W 待机功耗...0.6W 体积...5x50x0mm (WxHxD) 重量...5kg

5 关于遥控器如果遥控器距离本机很近时操作仍无效请用新电池更换如果要长时间不使用遥控器请取出遥控器的电池按照电池处置的地方性法规处置废旧电池遥控器的使用开关机静音音量加/向上进入菜单/确认进入二级菜单返回音量减/向下输出选择输入选择切换至控制无功能注意. 遥控器请使用节7号(AAA)电池. 第一次操作时先按 C 键

6 部件介绍 D SD. 579 MH z -R +L +R -L 旋钮按键指示灯待机红色开机蓝色红外遥控接收窗 5 显示屏 6 XLR 平衡耳机输出 7 6.5mm 非平衡耳机输出 8 平衡线路输出 9 单端线路输出 0 同轴输入 USB 输入光纤输入 IS 输入电压选择开关 5 电源插座 6 保险盒(内含一枚备用保险) 7 电源开关注旋钮音量加减菜单切换功能选择按键短按进入菜单确认长按退出菜单开关机 IS输入使用普通的HDMI线连接不需要使用特制的线材

7 界面介绍. 主界面 5 D SD. 579 MH z 5 输出方式显示为前级输出为耳放输出音量显示音频格式输入方式显示 5 采样率显示注当启用静音时此处显示MUTING 当无信号输入时此处显示NO SIGNAL

8 菜单功能介绍. 菜单界面. INPUT (输入方式) SETUP MENU USB OPTI INPU T OUTPUT (光纤) COAX (同轴) IS MOD E IS IS DSD L/R FIL TER. OUTPUT (输出方式) DIMMER LINE OUT (路线输出) HP SE OUT (单端耳机输出) SYSTEM HP BAL OUT (平衡耳机输出). IS MODE IS NORMAL (正常) IS INVERTED (反相) IS模式设置由于IS接口并非一个真正意义上有统一标准的接口因此不同厂家在引脚定义上会有不同因此我们设计一级菜单用于改变这些模式. Normal就是我们定义的接口定义如下图. IS INVERTED是LRCK和DATA两组型号的相位是相反的如下图 IS 接口引脚定义 DATA/ DSDR+ DATA/ DSDR LRCK/ DSDL+ LRCK/ DSDL DSDOE(:DSD 0:PCM) BCLK / DSDCLK+ BCLK / DSDCLK M CLK + M CLK FS CHANGE DATA/ DS DRDATA/ DS DR+ LRCK/ DSDLLRCK/ DSDL+ DSDOE(:DSD 0:PCM ) BCLK/ DSDCLK+ BCLK/ DSDCLK MCLK+ MCLK FS CHANGE IS NORMAL IS INVERTED 图图

9 菜单功能介绍. IS DSD L/R (IS输入DSD状态左右声道设置) 注由于不同的数字音源在DSD格式定义上不一定一致因此我们 NORMAL 正常加入了这个菜单用于交换DSD SWAPPED 左右声道交换播放时音频的左右声道此设置仅对DSD信号有效不影响 PCM播放时的声道设置 5. FILMMER (PCM 滤波器) FAST LINEAR (快速滚降线性相位滤波器) SLOW LINEAR (慢滚降线性相位滤波器) APODIZING (切迹快速滚降线性相位滤波器) FAST MINIMUM (快速滚降最小相位滤波器) SLOW MINIMUM (慢滚降最小相位滤波器) FAST HYBRID (混合快速滚降最小相位滤波器) BRICKWALL (矩形滤波器) 6. DIMMER (显示屏亮度设置) LEVEL ~ LEVEL 9 7. SYSTEM (系统版本信息) 本页菜单显示系统信息例如型号名称版本号等... 恢复出厂设置机器在未通电状态下按住开机键再通电直到显示屏显示logo之后松开按键

10 Hi-Res Digital To Analog Converter USER MANUAL Shenzhen DaHao Technology Co.,Ltd.

11 Safety Notes Install this unit in a well ventilated, cool, dry, clean place-away from direct sunlight, heat sources, vibration, dust, moisture, or cold.. Do not attempt to modify or fix this unit. Contact qualified Sabaj service personnel when any service is needed. The cabinet should never be opened for any reason. When not planning to use this unit for long periods of time ( i. e. when going onvacation), disconnect the power cable from the AC wall outlet. When not planning to use this unit for long periods of time (i.e. when going on vacation), disconnect the power cable from the AC wall outlet. Warranty Terms. The term of service Shenzhen Sabaj technology Co.,LTD promise good quality products. If product is defective unit by normal use with in 7daysafterpurchasing. The customer can choose to return or repair warranty( does not affect the secondary sales afterthey can return). Faulty for free with in one year warranty normal use.. Date of purchase is in accordance with invoice date or receipt date issued by seller, online shopping can cut trade shots.. Following situation can not enjoy Three Guarantees service a. All damages by human factors, including use it under nonrmal workingenvironment the and not following manual instruction. b. User privately disassemble, modification, maintenance. c. Use non-designated or approved accessories cause damage. d. QC or warranty stickers damage on cabinet. e. Can not provide a valid purchasing prove. f. Not belong to Sabaj product.. How to warranty This term is only suitable for china mainland, other regionplease refer to the policy of the local sales agents and national regulations.

12 Features The top performance D/A chip ES908PRO from ESS Technology. The high-performance power supply chip ES9, the noise of ES9 is lower than uvrms, to pushed ES908PRO to the limit. XMOS XU-08, true bit audio processing, support DoP and Native DSD, and reaches bit/768khz and DS. Ultra-low phase noise NDK Japan crystal oscillator and high-speed CPLD is used for clock processing, to achieve very low Clock jitter. All inputs support DSD streaming, including coaxial and optical (DoP6). Special design of discrete components high current headphones amplifier for higher damping factor. Built-in high efficiency and low vibration transformer provides sufficient and low noise power supply. Special design of discrete components linear regulator for analog circuit. high-end dual op-amps OPA6 and a lot of audio grade components are used. JAS Hi-Res certification.

13 Specifications Input...USB / Optical / Coaxial / IS Output...Line (SE, XLR) / Headphones (SE, XLR) THD+N...DAC 0.000% Headphones 0.00% Dynamic range... XLR 7dB RCA db SNR... DAC 0dB Headphones 0dB USB transmission...asynchronization USB compatibility...windows 7 / 8 / 8. / 0, Mac OSX0.6 or Later Linux Bit depth... USB bit 6 ~ bit Optical / Coaxial bit 6 ~ bit Sampling rate...usb/is PCM. ~ 768kHz DSD.8 ~.579MHz Optical / Coaxial PCM. ~ 9kHz DSD DSD6(DoP) Headphone amplifier output power...xlr 9mW(Ω) 05mW(6Ω) 55mW(50Ω) mw(00ω) SE 80mW(Ω) 65mW(6Ω) 5mW(50Ω) 58mW(00Ω) Power Consumption...8W Standby power...0.6w Size...5x50x0mm (WxHxD) Weight...5kg

14 Remote Control Install x AAA batteries as instructions. When using the remote control, point it toward the remote con-trol signal receiver on the main unit from a distance of 5 m (6 ft) or less. Do not place obstructions between the main unit and the remote control. The remote control might not work if the remote control signal receiver on the unit is exposed to direct sunlight or bright light. If this occurs, try moving the unit. Beware that use of this remote control could cause the unin-tentional operation of other devices that can be controlled by infra. Operating the remote control Power ON/OFF Mute Volume /up MENU/OK Next level menu Return Volume /down Output select Input select Switch to control Invalid Note. This remote controller use x R0/AAA battaries.. When you first operate, press the C key first.

15 Parts Name D SD. 579 MH z -R +L +R -L Konb Button Power LED(OFF: RED, ON:BLUE ) IR window 5 Display 6 XLR phones jack 7 6.5mm phones jack 8 XLR line out 9 RCA line out Coaxial input USB input Optical input IS input Voltage Selector 5 Power inlet 6 Fuse(with a spare fuse inside) 7 Power Switch 0 Note:. Konb: Volume/Menu up or down. Button: Press to Menu/Enter Hold to Return or Power ON/OFF. IS input is connected by ordinary HDMI cable, and no special cable is required.

16 User Interface. Main 5 D SD. 579 MH z 5 Output mode indicates Line out Headphones out Volume Level Streaming Format Input mode indicates 5 Current Sample rate (Display "NO SIGNAL" when unlcok or no connection, or display "MUTING" when it is muting)

17 Setting Introduction. SETUP MENU. INPUT SETUP MENU USB INPU T OUTPUT OPTI COAX IS MOD E IS IS DSD L/R FIL TER. OUTPUT DIMMER LINE OUT SYSTEM HP SE OUT HP BAL OUT. IS MODE IS NORMAL IS INVERTED IS mode settings, because this "IS" interface is not really a unified standard interface, so different manufacturers will have different pins definitions, so we design a menu item to change these modes:. Normal is the interface definition we defined, as Figure.. Inverted is inverting the phase of "LRCK" and "DATA", as Figure. IS Pins Functions DATA/ DSDR+ DATA/ DSDR LRCK/ DSDL+ LRCK/ DSDL DSDOE(:DSD 0:PCM) BCLK / DSDCLK+ BCLK / DSDCLK M CLK + M CLK FS CHANGE DATA/ DS DRDATA/ DS DR+ LRCK/ DSDLLRCK/ DSDL+ DSDOE(:DSD 0:PCM ) BCLK/ DSDCLK+ BCLK/ DSDCLK MCLK+ MCLK FS CHANGE IS NORMAL IS INVERTED Figure Figure

18 Setting Introduction. IS DSD L/R NORMAL SWAPPED 5. FILTER FAST LINEAR SLOW LINEAR APODIZING FAST MINIMUM Note: This setting is for some digital source DSD ports definition is different, if you using the IS input and listening to DSD music and the L/R is wrong, try this setting! Note:. This unit has built-in 7 kinds of PCM digital filter, these filters are only valid when playback PCM music.. Different filter has different sound characters, try it on different kind of music. SLOW MINIMUM FAST HYBRID BRICKWALL 6. DIMMER LEVEL ~ LEVEL 9 7. SYSTEM This page shows the system infomations, model name, version... Factory Reset Connect the power cord when pressing the power button, until screen shows logo.

您對本產品的選擇充分顯示了您對音響設備的精通, 我們十分感謝您的惠顧, 並為本公司提供優質產品一貫傳統而感到無比的自豪為使您的裝置與使用能得到最好的發揮, 我們

您對本產品的選擇充分顯示了您對音響設備的精通, 我們十分感謝您的惠顧, 並為本公司提供優質產品一貫傳統而感到無比的自豪為使您的裝置與使用能得到最好的發揮, 我們 NT-503 USB DAC/Network Player 關於此機器的網路功能, 請看網路說明書使用者說明書與網路說明書可以從 TEAC Global Site (http://www.teac-global.com/) 下載 USB D/A 轉換器 / 網路播放機使用說明書欲播放 USB 快閃記憶體