客户 : CUSTOMER: 产品描述 : DESCRIPTION: 机种型号 : OUR MODEL NO: 承认书 SPECIFICATION FOR APPROVAL Switching power Supply/ 开关电源 Input:100~240V AC 50/60Hz Output: 5VDC3A QX30W050300FG 样品编号 : 日期 : SAMPLE NO: QX2014000474 DATE: 2014-05-14 产品颜色 : SAMPLE COLOR:Black 符合环保项 :RoHS White APPROVAL SIGNATURE/ 客户确认 核准 /APPROVED BY 审核 /CHECKED BY 检测 /TESTED BY Manufacturer/ 制造商 业务 /SALES 核准 /APPROVED BY 设计 /DESIGNED BY 杨录音 地址 : 中国广东省深圳市宝安区福永镇重庆路新福工业园 A6 栋 3 楼 Add:Floor3,Buiding A6,Xinfu lndustrial Zone,Chongqing Road,Fuyong Town, Baoan District,Shenzhen,China. Tel:0755-29609342 81443738 Fax: 0755-29776652 http://www.szstos.com E-mail: 业务部 sales@szstos.com 工程部 rd@szstos.com 1/11
版本目录 /Rev. List 版本 /Rev. 日期 /Date 描述 / Description 制订 /Design A0 2014-05-14 新版本 /New Rev. XXJ Table of contents 1 描述 / DESCRIPTION 3 2 输入特性 /INPUT CHARACTERISTICS 3 3 输出特性 /OUTPUT CHARACTERISTICS... 4-5 4 保护功能 /PROTECTION FUNCTION.. 5 5 环境要求 /ENVIRONMENTAL REQUIREMET...5~6 6 安全及 EMI 要求 /SAFETY AND EMC REQUIREMENT.. 6 7 结构参数 /MECHANICAL REQUIREMENT.... 7 8 线材 /CORD... 8 9 铭牌附图 /LABEL......... 9 10 包装说明 /PACKING.... 10 11 测试报告 /ELECTRICAL TEST REPORT.. 11 2/11
1 描述 / DESCRIPTION: 本规格书适应于 QX30W050300FG 型号的开关电源. The purpose of the document is to specify the functional requirements of a 15 W switching power supply. 2 输入特性 /INPUT CHARACTERISTICS: 2.1 输入电压 /Input Voltage: 额定电压 /Rated Voltage:100~240Vac 调整范围 /Variation Range:90-264Vac 2.2 输入频率 /Input Frequency: 额定频率 / Rated Frequency: 50/60Hz. 调整频率 /Variation Frequency:47-63Hz 2.3 输入电流 /Input Current: 当输入交流电压为额定值的下限电压负载满载时, 最大输入交流电流 0.8A. 0.8Amps max At any input voltage and rated, DC output rated load. 2.4 浪涌电流 /Inrush Current: 当输出为额定负载, 环境温度为 25, 输入 240Vac 冷态起机时无损坏. When the output of the rated load, the ambient temperature is 25, input from 240Vac cold machine without damage to 2.5 AC 漏电流 /Ac Leakage Current: 当输入电压 240Vac 时, 最大漏电流为 0.25mA. 0.25mA Max.At240Vac input. 3/11
3 输出特性 /OUTPUT CHARACTERISTICS: 3.1 输出功率 /Power output 电压 最小负载 额定负载 峰值功率 输出功率 Voltage Min. Load Rated. Load Peak Output power 5Vdc 0.01A 3A 15W 3.2 负载特性, 调整率 /Combined Load/Line Regulation 电压 最小负载 额定负载 线性调整 负载调整率 Voltage Min. Load Rated. Load Line Regulation Load Regulation 5Vdc 0.01A 3A ±2% ±5% 3.3 纹波和噪音 Ripple and Noise: 测试条件 : 在输入 115/230Vac 和输出最小及最大负载时, 使用示波器带宽为 20MHz 连接到适配器的输出端, 同时输出端并联一个 47uF 的电解电容和一个 0.1uF 的瓷片电容. At 115/230Vac input and output Min and Max.Load, the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point. 电压 Voltage +5Vdc 最大纹波 / 最大噪音 Ripple and Noise(Max.) 150mV p-p 3.4 启动延迟时间 /Turn on delay time: 当输入 115Vac 和输出最大负载时, 最大启动时间为 3S. 2Seconds Max.at 115Vac input and output Max.load. 3.5 上升时间 /Rise time: 当输入 115Vac 和输出最大负载时最大时间为 40 ms. 40 ms Max.at 115Vac input and output Max load. 3.6 保持时间 /Hold up time: 当输入 115Vac 和输出最大负载时, 最小保持时间为 5 ms. 5 ms Min.at 115Vac input and output Max.Load. 3.7 效率 /Efficiency: 当 115/230Vac 输入电压时,1/4,1/2,3/4 和满载计算平均效率, 最小 76.41% 76.41% Min, At 115/230Vac input voltage,1/4,1/2,3/4 and full load calculation average efficiency. 适配器满足能效 V Adapter meet efficiency lever V 4/11
3.8 过冲 /Overshoot: 在电源开启或关闭的时候, 最大 15%. 15% Max.When power supply at turn off/on. 4 保护功能 /PROTECTION FUNCTION: 4.1 短路测试 /Short circuit test: 该电源供给器在短路解除时能正常工作恢复. The power supply will be auto recovered when short circuit faults remove. 4.2 过流保护 /Over current Protection: 过流故障排除后, 电源将自动恢复正常工作. The power supply will be auto recovered when over current faults remove. 5 环境要求 /ENVIRONMENTAL REQUIREMET: 5.1 工作温度 /Operating Temperature: 0-40, 满载, 正常工作. 0 to 40,Full load, Normal operation. 5.2 储藏温度 /Storage Temperature:-20 to 80 带外壳 /With package 5.3 工作湿度 /Relative Humidity: 5%(0 )~90%(40 ),72 小时, 满载, 正常工作. 5%(0 )~90%(40 )RH,72Hrs,Full load, Normal operating. 5.4 振动 /Vibration: 1. 测试标准 : 国际电工电子委员会 Operating: IEC 721-3-3 3M3 5~9Hz,A=1.5mm 加速度 (9~200Hz,Acceleration 5m/S2) 2. 运输 /Transportation: IEC 721-3-2 2M2 5-9Hz,A=3.5mm 9~200Hz, 加速度 Acceleration=5m/S2 200~500Hz, 加速度 Acceleration=15m/S2 5/11
3. 轴向振动 /Axes,10 cycles per axis. 在测试过程中不能出现永久性的损坏. No permanent damage may occur during testing. 在电源开启和关闭后, 样机能够恢复到最初条件. The SAMPLE has to restore to its original situation after power off/on.. 5.5 跌落试验 /Dropping Packed: 跌落高度为 760mm; Drop the height is760mm; 测试台面是厚 13mm 的夹木板, 离地面高 19-20mm The horizontal surface consists of hardwood at least 13mm thick, mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor. 6 安全及 EMI 要求 /SAFETY AND EMI REQUIREMENT: 6.1 安全 : 符合标准 :EN60065 Safety:accord with EN60065 6.2 高压 /DIELECTRIC STRENGTH Hi-Pot: 初级对次级 /Primary to secondary: 3000Vac/10mA/60S or 4242Vdc/5mA/60S for type test. 6.3 绝缘阻抗 /Iusulation resistance: 初级对次级 /Primary to secondary:20mω min at 500V DC. 6.4 EMI 标准 /EMI STANDARD Meets the Limits of/ 测试符合 <1>.Fcc part15 class B rules <2>.EN55022 class B rules <3>.GB9254-1998,GB17625.1-2003 <4>.AS/NZS CISPR22:2006. 6/11
7 结构参数 /MECHANICAL REQUIREMENT: 7.1 外壳 /Enclosure: The power supply size: L72x W43x H49mm; 外壳尺寸 : L72x W43x H49mm; 7.2 输入线 /Input Connector: 2 Pin EU 插脚 /Two pin input plug of EU. 7/11
8 线材 /CORD: 型号 /Our model: QX18W050300FU 日期 /Date:2014-5-14 样品编号 /SAMPLE No: QX2014000474 NOTE: 1>2468 18AWG 80 C 300V VW-1 L=1200±50mm; 2>PLUG:5.5*2.1*9mm, 直头音叉凹槽, 加磁环, 内正外负,inside"+",outside"-"; 3>Color:Black; 40±2 3.5±0.5 A 4>RoHS. A 6.5+0.1 7±0.05 1200±50 9±0.5 70±10 50±10 5.5±0.05 2.1+0.05 A - A 页码 : 8/10
9 铭牌 /LABEL: C2x45 C R AC ADAPTOR MODEL:QX30W050300FG INPUT:100-240V ~ 50/60Hz 0.8A OUTPUT:5V 3.0A YYWW EFFICIENCY LEVEL: 29.7 R2x3 TUV Rheinland Group geprufte Sicherheit MADE IN CHINA 20.7 NOTE: 1. 颜色 /Coior: 黑底白字 / Black ground white 2. 材质 /Material:PET+ 雾面 /fog surface 3. 厚度 /Thickness:0.20mm 4. 误差 /Toilerance:+0/-0.2mm 5. 环保 /RoHS 6.YYWW,YY 表示年份,WW 表示周数 9/11
10 包装说明 /PACKING: 平板 /Slab 外箱 /Outside box A 绿色字体 / B Green lettering 04 PE-LD 透气孔 Breathe freely os 包材 /Packaging: A:L452*51mm B:420*51mm 外箱内径 /Outside box:l460*w430*h225mm 平板 /Slab:L450*W420*2mmT 胶袋 /Pe bag:l160*w150*0.03mmt 数量 /Quantity:96PCS/CTN 10/11
11 测试报告 /ELECTRICAL TEST REPORT: No 序号 1 Test item 测试项目 Output Voltage 输出电压 Test condition 测试条件 Vin100Vac 60Hz Io=0 输入 100Vac 空载 Standard spec 标准规格 Test data 测试数据 1 2 3 4 5 Unit 单位 Judge 判定 Pass/ Fail 5±5%V 5.17 5.16 V Pass 2 3 4 5 6 7 8 9 10 11 Output Voltage 输出电压 Average Efficiency 平均效率 Ripple&Noise mvp-p 纹波 & 杂讯 Line Regulation 线性调整率 Standby Power 待机功耗 Short circuit test 短路测试 OCP 过电流保护 Output Voltage 输出电压 Output Voltage 输出电压 Average Efficiency 平均效率 Vin100Vac 60Hz Io=Rated Current 输入 100Vac 60Hz 负载 Vin 115Vac 60Hz 输入 115Vac 60Hz Vin100Vac 60Hz Full load 输入 100Vac 60Hz 满载 Vin=100V~240V Io=Rated Current 额定电流 Vin 115Vac 60Hz Io=0 输入 115Vac 60Hz Vin100Vac 60Hz 输入 100Vac 空载 Vin100Vac 60Hz 输入 100Vac Vin240Vac 50Hz Io=0 输入 240Vac 空载 Vin240Vac 60Hz Io=Rated Current 输入 240Vac 60Hz 负载 Vin230Vac 50Hz 输入 230Vac 50Hz 5±5%V 4.83 4.82 V Pass 76.41% 76.80 76.91 % Pass 150mVp-p 50 50 mvp-p Pass ±2% OK OK Pass 0.3W max 0.11 0.10 W Pass No odor smoke fire plastic deformation and excessive heat happen. 无冒烟, 起火, 外壳变形及过热现象 OK OK Pass 4AMax 3.54 3.46 A Pass 5±5%V 5.17 5.16 V Pass 5±5%V 4.83 4.81 V Pass 76.41% 76.52 76.62 % Pass 12 Ripple & Noise mvp-p 纹波 & 杂讯 Vin240Vac 50Hz Full load 输入 240Vac 50Hz 额定电流 150mVp-p 50 50 mvp-p Pass 13 14 15 16 17 18 19 Line Regulation 线性调整率 Standby Power 待机功耗 Short circuit test 短路测试 OCP 过电流保护 Hi-pot test 高压测试 Burn in 老化 Drop test 跌落 REMARK 备注 Vin=100V~240V Io=Rated Current 输入 100V~240V Vin230Vac 50Hz Io=0 输入 230V 50Hz Vin240Vac 50Hz 输入 240Vac 50Hz Vin230Vac 50Hz 输入 230Vac 50Hz ±2% OK OK Pass 0.3W max 0.22 0.22 Pass No odor smoke fire plastic deformation and excessive heat happen. 无冒烟, 起火, 外壳变形及过热现象 高压 /DIELECTRIC STRENGTH Hi-Pot: 初级对次级 /Primary to secondary:4242vdc/5ma/60s for type test Input:220Vac/50Hz Full Load 4hrs 输入 220Vac/50Hz 满载 4 小时 Heigh:1m Three*faces(once on each plane) 高 1 米,3 个面, 每面 1 次. OK OK Pass 4AMax 4.06 3.85 A Pass OK OK Pass OK OK Pass OK OK Pass 11/11