1
Main H/W Monitor Boot Security Exit System Overview System Time System Date [ 17:00:09] [Fri 02/25/2005] BIOS Version : P4VM800 BIOS P1.00 Processor Type : Intel (R) Pentium (R) 4 CPU 2.40 GHz Processor Speed : 2400 MHz Cache Size : 512KB Microcode Update : 0F24/1E Total Memory DIMM 1 DIMM 2 : 256MB with 64MB shared memory : 256MB/166MHz (DDR333) :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field 2
Main H/W Monitor Boot Security Exit Settings Configure CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen CPU Configuration CPU Host Frequency Actual Frequency (MHz) Boot Failure Guard Spread Spectrum [200] [Enabled] Select how to set the CPU host frequency. Ratio Status Ratio Actual Value CPU Thermal Throttling Hyper Threading Technology Max CPUID Value Limit :Locked :16 [Enabled] F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
Chipset Configuration DRAM Frequency Flexibility Option DRAM CAS# Latency DRAM Command Rate DRAM Voltage AGP Voltage Primary Graphics Adapter AGP Aperture Size AGP Mode AGP Fast Write Onboard AGP Share Memory PCI Delay Transaction OnBoard LAN OnBoard AC'97 Audio Onboard MC'97 Modem [2T Command] [PCI] [64MB] [Eabled] Options 133MHz (DDR266) 166MHz (DDR333) 200MHz (DDR400) Auto + - Change Option 4
5
ACPI Configuration Suspend To RAM Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On [Power Off] Select auto-detect or disable the STR feature. 6
IDE Configuration OnBoard IDE Controller SATA Operation Mode Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave SATA1 SATA2 [Both] [RAID] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] DISABLED: disables the integrated IDE Controller. PRIMARY: enables only the Primary IDE Controller. SECONDARY: enables only the Secondary IDE Controller. BOTH: enables both IDE Controllers. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported Select the type of device connected to the system. 7
8
PCI / PnP Configuration PCI Latency Timer PCI IDE BusMaster [32] [Enabled] ValueinunitsofPCI clocks for PCI device latency timer register. Floppy Configuration Floppy A Floppy B 1 [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. 9
Configure Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ [Enabled] [3F8 / IRQ4] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller. 10
USB Configuration USB Controller USB 2.0 Support Legacy USB Support [Enabled] [Enabled] To enable or disable the onboard USB controllers. Main H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature : 37C/98F : 31C/87F CPU Fan Speed Chassis Fan Speed : 2463 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V : 1.629V : 3.306V : 5.067V : 11.890V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit 11
Main H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration 1st Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [2nd Floppy Device] [3rd Floppy Device] Configure Settings during System Boot. Enter Go to Sub Screen Boot Boot Settings Configuration Boot From Network VIA SATA Raid Utility Bootup Num-Lock [Enabled] [On] To enable or disable the boot from network feature. + - Change Option 12
Main H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 13
Main H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 14