Spec. R2A-700D1V2 - V1.3

Size: px

Start display at page:

Download "Spec. R2A-700D1V2 - V1.3"

亿屈
5 years ago
Views:

08 2011 版本描述 Revision Description 背板 DC-DC 線路調整 Modified the circuit for DC-DC backplane 修改者客戶認可認可日期 Modify By Cust. Approval App. Date Kevin Chen AUG.

1 Issued Date : 11/09/2012 SPECIFICATION 產品規格書產品名稱 / Model Name:R2A-700D1V2 產品描述 / Description:700W+700W Redundant Power Supply. 版本 / Revision:1.3 修改紀錄 / Revision History 版本日期 Rev. Date 1.0 AUG 版本描述 Revision Description 背板 DC-DC 線路調整 Modified the circuit for DC-DC backplane 修改者客戶認可認可日期 Modify By Cust. Approval App. Date Kevin Chen AUG.10, Jan. 09 Modified the 6.3 value. Jacky Jan Jan. 09, Aug.28, 2012 Modified item 12 Environmental Jacky Jan Sep. 06, Nov.09, 2012 Modified the 14.2 DC output cables and stick Mindy Chung Nov. 12, 2012 提交 / Prepared BY 檢查 / Checked BY 批准 / Approved BY KEVIN JACKY 1

2 目錄 Contents 1. 概述 General Description 2. 輸入規格 Input Characteristics 2.1. 交流輸入電壓和頻率範圍 AC Input voltage and frequency 2.2. 輸入電流與浪湧電流 Input current and inrush current 2.3. 功率因數 Power Factor 3. 效率 Power Efficiency 4. 輸出規格 Output Characteristics 4.1. 輸出電壓電流調整率 Output Voltage & Current Regulation 4.2. 輸出紋波和噪音 DC Output Ripple & Noise 4.3. 輸出保持時間 Hold Up Time 4.4. 上升時間 Rise Time 4.5. 動態響應時間 Dynamic load response time 4.6. 遠端開關控制 Remote on/off control 5. 電源良好信號 Power good signal 6. 保護 PROTECTION 6.1. 過壓保護 Over voltage protection 6.2. 低壓保護 Under-voltage protection 6.3. 過流保護 Over current Protection 6.4. 短路保護 Short circuit protection 6.5. 過熱保護 Thermal Protection 7. 電源信號狀態 Power System Signal status 7.1. 蜂鳴器狀態 Buzzer status 7.2. 燈號指示 LED indicators 7.3. TTL 信號 TTL signal 8. 負載均流 Load sharing 2

3 9. 絕緣性能 Isolation 9.1. 絕緣電阻 Insulation Resistance 9.2. 耐壓絕緣 Dielectric Withstand Voltage 9.3. 漏電電流 Leakage current 10. 安全要求 Safety Requirements 11. 電磁相容 EMC 電磁干擾 EMI 電磁相容 EMS 12. 環境條件 Environmental 溫度 Temperature 環境濕度 Humidity 海拔高度 Altitude 冷卻方式 Cooling Method 13. 可靠性 Reliability 13.1 平均故障失效時間 MTBF Qualification 14. 機械尺寸和電源連接器 Mechanical 2D Drawing and Power Connector 外觀尺寸圖 Outside Dimension 輸出端線材 DC Output cables 3

4 1. 概述 General Description This specification describes the performance characteristics of a 700 watts hot swappable, 1+1 power system with +3.3V,+5V,+12V, -12V main DC outputs, and 5V standby outputs. The system is configured to hold two identical 700W power supply modules, Model R2A-700D1V2. 2. 輸入規格 Input Characteristics 2.1. 交流輸入電壓和頻率範圍 AC Input voltage and frequency 最小值 Minimum 正常值 Nominal 最大值 Maximum 單位 Unit ~ 伏特 VAC 47 50~60 63 赫茲 Hz 2.2. 輸入電流與浪湧電流 Input current and inrush current 交流輸入電壓 AC Input Voltage 最大輸入電流 MAX. Input Current per power supply module 浪湧電流 Inrush Current per power supply module 115Vac 12A 30A 230Vac 6A 60A 2.3. 功率因數 Power Factor 90Vac 115Vac 230Vac 264Vac >0.99 >0.98 >0.95 > 效率 Power Efficiency 在滿載狀態,115 伏特 60 赫茲輸入下, 電源效率為 80%(Min) The Minimum efficiency of the power supply is 80% at full load and 115Vac/60HZ input. 4

5 4. 輸出規格 Output Characteristics 4.1. 輸出電壓電流調整率 Output Voltage & Current Regulation 輸出電壓 Output Voltage 最小電流 Min. Current 額定電流 Rated current 調整率 REGULATION +3.3V 1A 25A ±5% +5V 1A 25A ±5% +12V 1A 57A ±5% -12V 0A 1A ±5% +5VSB 0.5A 3.5A ±5% Note: 5V 和 3.3V 相加總不可超過 190 瓦. The combined total power from 5V & 3.3V shall not exceed 190W 輸出紋波和噪音 DC Output Ripple & Noise Output Voltage Ripple & Noise (Max.) +3.3V 60mVp-p +5V 60mVp-p +12V 120mVp-p -12V 120mVp-p +5VSB 50mVp-p Note: 1. 紋波和噪音頻寬設置在 20 兆赫茲 Ripple & Noise bandwidth is set to 20MHz 2. 輸出端並聯一個 0.1 uf 陶瓷電容和一個 10 uf 電解電容, 測試紋波和噪音 Use a 0.1uF ceramic capacitor in parallel with a 10uF electrolytic capacitor at output connector terminals for ripple & noise measurements 4.3. 輸出保持時間 Hold Up Time Output Voltage 115VAC Input 230VAC Input +3.3V >16ms >16ms +5V >16ms >16ms +12V >16ms >16ms -12V >16ms >16ms +5VSB >16ms >16ms Note: 所有輸出在滿載狀態 All of dc output at full load. 5

6 4.4. 上升時間 Rise Time Output Voltage 115/230Vac Input & Full Load +3.3V 20ms (max.) +5V 20ms (max.) +12V 20ms (max.) -12V 20ms (max.) +5VSB 20ms (max.) Note: 上升時間為輸出電壓從 10% 上升至 90% 的時間 The rise time measured is when the output voltages rise from10% to 90% of specified output voltage Vout observed on the channel waveform 動態響應時間 Dynamic load response time The following shall apply to the 3.3 V, 5 V, and 12 V outputs: Output voltage for each output shall recover to within 5 % of its steady state level in less than 1 ms under the following conditions: AC Input Voltage: 90VAC ~ 264VAC Repetition rate of 100Hz with 50 % duty cycle Output Step Load Size Load Slew Rate Capacitive Load +3.3V 30% to 100% to 30% load 0.5 A/u sec 6000uF +5V 30% to 100% to 30% load 0.5 A/u sec 6000uF +12V 60% to 100% to 60% load 1 A/u sec 6000uf +5SB 0% to 100% to 0% load 0.5 A/u sec 350uF 4.6. 遠端開關控制 Remote on/off control The main outputs of this power supply (3.3V,5V,12V,-12V) shall be energized when input signal*pson is active. *PSON is an active low TTL compatible signal referenced to the +5V standby common. This input signal shall be an open collector signal capable of sinking a minimum of 1.6mA. When *PSON becomes inactive, the main outputs shall be disabled. PSU on PSU off PSON Signal LOW (0.8V max) HI (2V max) 6

7 5. 電源良好信號 Power good signal The system shall have an active high TTL compatible signal capable of sinking 1mA and sourcing 100uA. The signal shall become active within 100 to 500 ms from the instant +5V output reaches a steady state level within the specified regulation limits. It shall become inactive at least 1 ms before +5V drops to below the lower regulation limit. Power 115/230VAC, Full Load 200ms ~ 500ms Power 115/230VAC, Full Load 1ms (Min.) 6. 保護 Protection 6.1. 過壓保護 Over voltage protection Output Min Max Comments +3.3V 3.75V 4.3V PSU shutdown +5V 5.7V 6.9V PSU shutdown +12V 13V 14.3V PSU shutdown Note: 應該在最大交流輸入電壓 230 伏和輕載空載下測試 The power supply shall be test at max AC voltage (230Vac) and min load or no load 低壓保護 Under-voltage protection Output Min Max Comments +3.3V 2.0V 2.4V PSU shutdown +5V 3.3V 3.7V PSU shutdown +12V 8.5V 9.5V PSU shutdown Note: 應該在最大交流輸入電壓 230 伏和輕載空載下測試 The power supply shall be test at max AC voltage (230Vac) and min load or no load 過流保護 Over current protection Output Over Current(Type) Over Current(Max.) Comments +3.3V 27.5A 37.5A PSU shutdown +5V 27.5A 37.5A PSU shutdown +12V 62.7A 85.5A PSU shutdown Note: 過流保護測試是在其他額定負載時測試 The over current protection should be tested at other load rating. 7

8 6.4. 短路保護 Short circuit protection Output Comments +3.3V PSU shutdown +5V PSU shutdown +12V PSU shutdown Note: 短路保護測試是在其他額定負載時測試 The Short circuit protection should be tested at other load rating 過熱保護 Thermal Protection 當外殼溫度超過 86 (±5 ), 電源將進入過熱保護狀態當溫度恢復正常, 而且電源重新啟動之後, 可以恢復操作 The power supply shall go into thermal protection as the case temperature exceeds 86 (±5 ) limit. The output shall recover only when the temperature becomes normal and AC power is turned on again. 7. 電源信號狀態 Power System Signal status 7.1. 蜂鳴器狀態 Buzzer status Power Supply Condition No AC power to all PSU AC present/only Standby Output On Power supply DC outputs ON and OK Power supply failure Buzzer status OFF OFF OFF Beeping 7.2. 燈號指示 LED indicators Power Supply Condition Power system status Per Power Module status LED Color RED GREEN ORANGE No AC power to all PSU OFF OFF OFF AC present/only Standby Output On ON OFF OFF Power supply DC outputs ON and OK OFF ON ON Power supply failure OFF Blinking OFF 8

9 7.3. TTL 信號 TTL signal POWER SUPPLY CONDITION OUTPUT CONDITION Min. Max. NORMAL(POWER SUPPLY ON) 3V 5.25V FAILURE(POWER SUPPLY OFF) 0V 1V 8. 負載均流 Load sharing 輸出電壓 Output Voltage 負載電流 Load Current 負載均流電壓 Load Share Voltage +12V 1A +0.48V ~ +0.52V +5V 1A +0.33V ~ +0.37V +3.3V 1A +0.33V ~ +0.37V 9. 絕緣性能 Isolation 9.1. 絕緣電阻 Insulation Resistance Input To Output 500Vdc, 50M ohms Min.( at room Temperature) Input To FG Output To FG 500Vdc, 50M ohms Min.( at room Temperature) Non Insulation 9.2. 耐壓絕緣 Dielectric Withstand Voltage Input To Output 1834Vac (30 ma) for 1 Minute. Input To FG Output To FG 1834Vac (30 ma) for 1 Minute. Non Insulation 9.3. 漏電電流 Leakage current 在伏特 /50-60 赫茲情況下, 最大漏電流為 3.5mA 3.5mA max. at 120~264Vac/50~60HZ. 10. 安全要求 Safety Requirements -IEC TUV EN UL or cul -BSMI -CCC 9

10 11. 電磁相容 EMC 電源電磁干擾滿足以下標準 The power supply shall comply with the following criterion: 電磁干擾 EMI 1) Conduction Emission:( 傳導干擾度 ) A.EN55022:2006/A1:2007 CLASS A; EN55024:1998/A1:2001/A2: B.CISPR PUB.22 and FCC PART 15 SUBPART B CLASS A. 2) Radiated Emission : ( 幅射干擾度 ) A.EN55022:2006/A1:2007 CLASS A; EN55024:1998/A1:2001/A2: B.CISPR PUB.22 and FCC PART 15 SUBPART B CLASS A. 12. 環境條件 Environmental Temperature Operating : 0 to +40 Non Operating: -20 to Humidity Operating : 5% to 95%, non-condensing Non Operating: 20% to 90%,non-condensing Altitude: Altitude during operation: Up to 2000 m Altitude of test laboratory: Below 2000 m 冷卻方式 Cooling Method BY BALL BEARING DC FAN. 13. 可靠性 Reliability 13.1 平均故障失效時間 MTBF Qualification Using MIL - HDBK -217F the calculated MTBF>100,000 hours at 25 10

11 14. 機械尺寸和電源連接器 Mechanical 2D Drawing and Power Connector Outside Dimension:265(D)x101(W)x84(H)mm 修訂 REVISIONS 版次 REV 記述 DESCRIPION 簽名 SING 日期 DATE 6#-32(X3) RESET 開關 6#-32(x4) 容許公差 : TOLEANCES:.XXX=.XX=.X= 投影法 : PROJECTION: 第三角法材料規格 MATERIAL ±.025 ±.1 核准者審核者繪圖者 ±.2 APPROVE BY CHECK BY DRAW BY JACKY 單位 UNITS 圖號 DRAW NO 編號 SHEET 日期 DATE mm 品名 OF R2A-600D1V2 外觀尺寸圖 MODEL NO 料號 May,5,2010 PART NO 11

12 DC Output cables L=470mm±20mm Pins Connector HOUSING: MOLEX or equivalent TERMINAL: MOLEX or equivalent Pin No. COLOR 1 YELLOW +12V 2 YELLOW +12V P6 Power Module/System Status LED Alarm Reset Switch Connector YELLOW BLACK BLACK BLACK BROWN / WHITE RED / WHITE GREEN / WHITE TTL Signal Cable +12V COM COM COM POWER Module/System Status LED Name PW1LED PW2LED External LED COLOR BROWN RED GREEN WHITE WHITE WHITE L=480mm+/-20mm L=480mm+/-20mm L=470mm+/-20mm TTL Signal Connector HOUSING: Molex or equivalent Pin COLOR No. 1 BLACK COM 22AWG 2 RED +5V 22AWG ALARM Reset Switch Connector Pin No. 1 2 COLOR GRAY GRAY COM REST LED COLOR 22AWG 22AWG ORANGE ORANGE RED/ORANGE 860mm ±20mm 470mm ±20mm 22AWG 22AWG 22AWG 860mm ±20mm 5 LED ORANGE 5 LED ORANGE 5 LED H2510 External LED RED / ORANGE PW1 LED PW2 LED 187P PN PO PP PQ BLACK (COM) RED (+5V) GRAY (COM) GRAY (RESET) 860mm ±20mm 1 (1-3) 2 (4-6) 3 (7-9) 4 (10-12) 5 (13-15) (1-3) (4-6) (7-9) (10-12) (13-15) 1 (1-3) 3 2 (4-6) (7-9) 4 (10-12) 5 (13-15) 1 (1-3) 3 2 (4-6) (7-9) 4 (10-12) 5 (13-15) P6 L=470mm±20mm L=470mm±20mm L=480mm+/-20mm L=480mm+/-20mm L=480mm+/-20mm L=480mm+/-20mm L=150mm +/-10mm 22AWG 1007 PA PB PC PD PE PF PG PH PI PJ PK PL PM 3 PIN8 PIN P24 P8 P4 容許公差 : TOLEANCES:.XXX=.XX=.X= 投影法 : PROJECTION: 第三角法 24Pins(EPS12V) Connector HOUSING: MOLEX or equivalent TERMINAL: MOLEX or equivalent P24 Pin No COLOR ORANGE(+3.3V) ORANGE(+3.3V) RED(+5V) RED(+5V) GRAY(PG) 材料規格 MATERIAL 核准者審核者 APPROVE BY. CHECK BY. PURPLE(+5VSB) YELLOW (+12V) YELLOW (+12V) ORANGE(+3.3V) 繪圖者 DRAW BY. Kevin 470mm/20AWG 單位 UNITS 圖號 DRAW NO 編號 SHEET 日期 DATE Pin No mm OF 2011,11,02 COLOR ORANGE(+3.3V) BLUE(-12V) GREEN(PS-ON) NC ORANGE(+3.3Vs) 470mm/22AWG RED(+5V) RED(+5V) RED(+5V) 8 YELLOW +12V 4Pins(ATX12V,FOR P4) Connector HOUSING: MOLEX or equivalent TERMINAL: MOLEX or equivalent Pin No. COLOR 1 BLACK COM 2 BLACK COM P4 3 YELLOW +12V 4 YELLOW +12V 4Pins(HD/CD-ROM/RW):P4H1~P4H4 Connector HOUSING: AMP or equivalent TERMINAL:AMP or equivalent 4Pins(FLOPPY DISK):P4F Connector HOUSING: AMP or equivalent 品名 MODEL NO 料號 PART NO 470mm/20AWG 8Pins(EPS12V) Connector HOUSING: MOLEX or equivalent TERMINAL: MOLEX or equivalent Pin No. COLOR 1 BLACK COM 2 BLACK COM 3 BLACK COM P BLACK YELLOW YELLOW YELLOW COM +12V +12V +12V TERMINAL: AMP or equivalent Pin No. COLOR SIZE PA 1 YELLOW +12V PD 2 BLACK COM PG 3 BLACK COM PJ 4 RED +5V PB 1 YELLOW +12V PE 2 BLACK COM PH 3 BLACK COM PK 4 RED +5V PC 1 YELLOW +12V PF 2 BLACK COM PI 3 BLACK COM PL 4 RED +5V 1 YELLOW +12V 22AWG 2 BLACK COM 22AWG PM 3 BLACK COM 22AWG 4 RED +5V 22AWG 470mm ±15mm 470mm ±15mm 480mm ±15mm 150mm ±15mm 150mm ±15mm 150mm ±15mm S.ATA HDD HOUSING: MOLEX or equivalent TERMINAL: MOLEX or equivalent Pin No. COLOR 1 ORANGE +3V3 2 COM PN BLACK 3 RED +5V 480mm ±15mm PP 4 BLACK COM 5 YELLOW +12V Pin No. COLOR 1 ORANGE +3V3 PO 2 BLACK COM 3 RED +5V 150mm ±15mm PQ 4 BLACK COM 5 YELLOW +12V SS-R2A(12 ) 12

Sosen SS-50R-36 LED Driver Spec Sheet

Sosen SS-50R-36 LED Driver Spec Sheet SPECIFICATION 50W LED DRIVER Issued date: January 20, 2013 REV: V1.0 Model: SS-50R Description: 50W AC to DC LED DRIVER Customer: Customer Approval Signature SHENZHEN SOSEN ELECTRONICS CO LTD WRITTEN CHECKED