(Microsoft Word DH-NVR5208\243\254DH-NVR5216-CE)

Transcription

1 EMC TEST REPORT Authorized under Declaration of Conformity According to EN 55022:2010 EN : 2010 EN : 2007 EN : 2011 EN : 2006+A2: 2009 IEC : 2008 EN : 2008 IEC : 2010 IEC : 2012 IEC : 2005 IEC : 2008 IEC : 2009 IEC : 2004 Applicant : Zhejiang Dahua Vision Technology Co., Ltd Address : The 1st floor, building F, No.1199 Bin an road, Changhe Street, Binjiang District, Hangzhou, P.R. China Equipment : Network Video Recorder DH-NVR5204, DH-NVR5208, DH-NVR5216, DH-NVR5232, NVR5204, NVR5208,NVR5216, NVR5232, DH-NVR5204-P, Model No. : DH-NVR5208-P, DH-NVR5216-P, DH-NVR5232-P, NVR5204-P, NVR5208-P, NVR5216-P, NVR5232-P, DH-NVR5208-8P, DH-NVR5216-8P, DH-NVR5232-8P, NVR5208-8P, NVR5216-8P, NVR5232-8P The test result refers exclusively to the test presented test model / sample. Without written approval of Cerpass Technology(Suzhou) Corp. the test report shall not be reproduced except in full. This test report is only applicable to European Community. The test report must not be used by the clients to claim product certification approval by NVLAP or any agency of the Government. TEL: FAX: Page No. : 1 of 96

2 Contents CERTIFICATE OF COMPLIANCE Summary of Test Procedure and Test Results Immunity Testing Performance Criteria Definition Test Configuration of Equipment under Test Manufacturer Feature of Equipment under Test Test Software and Test Mode Description of Support Unit General Information of Test Measurement Uncertainty Test of Conducted Emission Test Limit Test Procedures Typical Test Setup Measurement equipment Test Data and Result Test Photographs Test of Radiated Emission Test Limit Test Procedures Typical test Setup Measurement equipment Test Result and Data Test Result and Data (30MHz ~ 1000MHz) Test Result and Data (1000MHz ~ 6000MHz) Test Photographs (30MHz ~ 1000MHz) Test Photographs (1000MHz ~ 6000MHz) Harmonics Test Limits of Harmonics Current Measurement Measurement equipment Test Result and Data Test Photographs Voltage Fluctuations Test Test Procedure Measurement equipment Test Result and Data Test Photographs Electrostatic Discharge Immunity Test Test Procedure Test Setup for Tests Performed in Laboratory Test Severity Levels TEL: FAX: Page No. : 2 of 96

3 8.4. Measurement equipment Test Result and Data Test Photographs Radio Frequency electromagnetic field immunity test Test Procedure Test Severity Levels Measurement equipment Test Result and Data Test Photographs Electrical Fast Transient/ Burst Immunity Test Test Procedure Test Severity Levels Measurement equipment Test Result and Data Test Photographs Surge Immunity Test Test Procedure Test Severity Level Measurement equipment Test Result and Data Test Photographs Conduction Disturbances induced by Radio-Frequency Fields Test Procedure Test Severity Levels Measurement equipment Test Result and Data Test Photographs Power Frequency Magnetic Field Immunity Tests Test Setup Test Severity Levels Measurement equipment Test Result and Data Test Photographs Voltage Dips and Voltage Interruptions Immunity Test Setup Test Conditions Measurement equipment Test Result and Data Test Photographs EUT Photographs TEL: FAX: Page No. : 3 of 96

4 History of this test report ORIGINAL. Additional attachment as following record: Attachment No. Date Description TEL: FAX: Page No. : 4 of 96

5 CERTIFICATE OF COMPLIANCE According to EN 55022:2010 EN : 2010 EN : 2007 EN : 2011 EN : 2006+A2: 2009 IEC : 2008 EN : 2008 IEC : 2010 IEC : 2012 IEC : 2005 IEC : 2008 IEC : 2009 IEC : 2004 Applicant : Zhejiang Dahua Vision Technology Co., Ltd Address : The 1st floor, building F, No.1199 Bin an road, Changhe Street, Binjiang District, Hangzhou, P.R. China Equipment : Network Video Recorder Model No. : DH-NVR5204, DH-NVR5208, DH-NVR5216, DH-NVR5232, NVR5204, NVR5208,NVR5216, NVR5232, DH-NVR5204-P, DH-NVR5208-P, DH-NVR5216-P, DH-NVR5232-P, NVR5204-P, NVR5208-P, NVR5216-P, NVR5232-P, DH-NVR5208-8P, DH-NVR5216-8P, DH-NVR5232-8P, NVR5208-8P, NVR5216-8P, NVR5232-8P I HEREBY CERTIFY THAT : The measurements shown in this test report were made in accordance with the procedures given in EUROPEAN COUNCIL DIRECTIVE 2004/108/EC. The test was carried out on Mar 04, 2013 at Cerpass Technology(Suzhou) Corp. Signature Miro Chueh/ Technical director TEL: FAX: Page No. : 5 of 96

6 1. Summary of Test Procedure and Test Results EMISSION(EN 55022:2010 / EN : 2007) Test Item Normative References Test Result Conducted Emission EN : 2010 EN : 2007 PASS Radiated Emission EN : 2010 EN : 2007 PASS Harmonics EN : 2006+A2: 2009 PASS Voltage Fluctuations EN : 2008 PASS IMMUNITY (EN : 2010) Test Item Test Spec Test Result Electrostatic Discharge Immunity Test (ESD) Radio Frequency electromagnetic field immunity test (RS) Electrical Fast Transient/ Burst Immunity Test (EFT) Surge Immunity Test Conduction Disturbances induced by Radio-Frequency Fields Power Frequency Magnetic Field Immunity Test Voltage Dips and Voltage Interruptions Immunity Test 4 kv (contact discharge) PASS 8 kv (Air discharge) MHz, 3V/m, 80%AM(1KHz) PASS AC Port: 1kV, Signal Port: 0.5 kv PASS AC Power Ports: Line to Line: 1 kv Line to earth: 2 kv PASS Signal and telecommunication port: 1 kv MHz, 3V, 80%AM(1KHz) PASS 50Hz, 1A/m PASS Voltage dips: >95% Reduction, 0.5 Durations (Cycle) PASS 30% Reduction, 25 Durations (Cycle) PASS Voltage interruptions: PASS >95% Reduction, 250 Durations (Cycle) TEL: FAX: Page No. : 6 of 96

7 IMMUNITY (EN : 2011) Test Item Test Spec Test Result Electrostatic Discharge Immunity Test (ESD) Radio Frequency electromagnetic field immunity test (RS) Electrical Fast Transient/ Burst Immunity Test (EFT) Surge Immunity Test Conduction Disturbances induced by Radio-Frequency Fields 6 kv (contact discharge) PASS 8 kv (Air discharge) MHz, 10V/m, 80%AM(1KHz) PASS AC Port: 2.0kV, Signal Port: 1.0 kv PASS AC Power Ports: line to line: 0.5,1 kv line to earth: 0.5,1,2kV PASS Signal Port: 0.5,1 kv MHz, 10V, 80%AM(1KHz) PASS Voltage Interruptions: PASS 100% Reduction, 250 Cycle Voltage Dips and Voltage Interruptions Immunity Test Voltage Dips: 60% Reduction, 10 Cycle 30% Reduction, 25 Cycle 20% Reduction, 250 Cycle PASS 2. Immunity Testing Performance Criteria Definition A. Normal performance within limits specified by the manufacture, requestor or purchaser; B. Temporary loss of function or degradation of performance which ceases after the disturbance ceases, and from which the equipment under test recovers its normal performance, without operator intervention; C. Temporary loss of function or degradation of performance, the correction of which requires operation intervention; D. Loss of function or degradation of performance which is not recoverable, owing to damage to hardware or software, or loss of data. TEL: FAX: Page No. : 7 of 96

8 3. Test Configuration of Equipment under Test 3.1. Manufacturer ZHEJIANG DAHUA TECHNOLOGY CO.,LTD. No.1187, BinAn Road, Binjiang District, Hangzhou city, Zhejiang province,china 3.2. Feature of Equipment under Test Network Video Recorder Model No.: DH-NVR5204, DH-NVR5208, DH-NVR5216, DH-NVR5232, NVR5204, NVR5208,NVR5216, NVR5232, DH-NVR5204-P, DH-NVR5208-P, DH-NVR5216-P, DH-NVR5232-P, NVR5204-P, NVR5208-P, NVR5216-P, NVR5232-P, DH-NVR5208-8P, DH-NVR5216-8P, DH-NVR5232-8P, NVR5208-8P, NVR5216-8P, NVR5232-8P Adapter1# Model No : ADS-65LSI G Input: V~ 50-60Hz 1.5A Output: 12V 5A DC Cable Non-shielding, 1.5m, with one ferrite core bonded Adapter2# Model No : FSP120-AFA DC Cable remark Input: V~ 50-60Hz 2A Output: 48V 2.5A Non-shielding, 1.5m, with one ferrite core bonded DH-NVR5232-P was selected as the test model and its data have been recorded in this report Test Software and Test Mode Test Software a During testing, the interface cables and equipment positions were varied according to Europe Standard. b Turn on the power of all equipment. C Connect the Test System and EUT. d Set the EUT working in test mode of normal operation, then test. The test modes for RE/H-F/ESD/RS/PFMF: Test Mode 1: Normal Operation The test modes for CE: Test Mode 1: Normal Operation with ADS-65LSI G Test Mode 2: Normal Operation with FSP120-AFA Test Mode 3: Normal Operation with FSP120-AFA+ ADS-65LSI G TEL: FAX: Page No. : 8 of 96

9 The test modes for ISN: Test Mode 1: Normal Operation for LAN Port(10Mbps) Test Mode 2: Normal Operation for LAN Port(100Mbps) Test Mode 3: Normal Operation for LAN Port(1000Mbps) Test Mode 4: Normal Operation for POE LAN Port(10Mbps) Test Mode 5: Normal Operation for POE LAN Port(100Mbps) The test modes for EFT/SURGE/CS/DIPS: Test Mode 1: Normal Operation with ADS-65LSI G Test Mode 2: Normal Operation with FSP120-AFA 3.4. Description of Support Unit No Device Manufacturer Model No. Description 1 Notebook PC DELL Vostro 3560 N/A 2 Notebook PC SONY PCG-71811P N/A 3 USB Keyboard DELL SK-8115 N/A 4 Camera DAHUA IP-HFW3100P N/A 5 USB Mouse DELL GOK02XYK N/A 6 LCD Monitor Lenove L2364wA N/A 7 LCD Monitor DELL 3008WFPt N/A 8 Microphone N/A N/A N/A 9 Earphone N/A N/A N/A 10 Monitor PINEER-TIMES PNT-14A N/A No Cable Quantity Description A VGA Cable 1 Shielded, 1.5m,with tow ferrite core bonded B HDMI Cable 1 Shielded, 1.5m, with tow ferrite core bonded C LAN Cable 3 Non-Shielded, 3.0m D BNC Cable 3 Non-Shielded, >3.0m E USB Cable 1 Shielded, 1.8m,with tow ferrite core bonded F USB Cable 1 Shielded, 1.2m G LAN Cable 3 Non-Shielded, >3.0m H RS232 Cable 1 Non-Shielded, 1.5m TEL: FAX: Page No. : 9 of 96

10 3.5. General Information of Test Test Site: Test Site Location : Cerpass Technology (Suzhou) Co.,Ltd No.66,Tangzhuang Road, Suzhou Industrial Park, Jiangsu , China NVLAP LAB Code : FCC Registration Number : , IC Registration Number : 7290A-1, 7290A-2 VCCI Registration Number : Frequency Range Investigated : Test Distance : T-1945 for Telecommunication Test C-2919 for Conducted emission test R-2670 for Radiated emission test below 1GHz G-227 for Radiated emission test above 1GHz Conducted Emission Test: from 150kHz to 30 MHz Radiated Emission Test: from 30 MHz to 1,000 MHz Radiated Emission Test: from 1GHz to 6GHz The test distance of radiated emission below 1GHz from antenna to EUT is 10 M. The test distance of radiated emission above 1GHz from antenna to EUT is 3 M. LABORATORY ACCREDITATION 3.6. Measurement Uncertainty Conducted Emission The measurement uncertainty is evaluated as ± 2.71 db. Radiated Emission (30MHz -1000MHz) (1G-6GHz) Horizontal The measurement uncertainty is evaluated as ±3.59 db. Vertical The measurement uncertainty is evaluated as ± 3.89 db Horizontal The measurement uncertainty is evaluated as ± 2.31 db. Vertical The measurement uncertainty is evaluated as ± 2.15 db. TEL: FAX: Page No. : 10 of 96

11 4. Test of Conducted Emission 4.1. Test Limit Conducted Emissions were measured from 150 khz to 30 MHz with a bandwidth of 9 khz and return leads of the EUT according to the methods defined in European Standard EN The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position producing maximum conducted emissions. Frequency range (MHz) Table 1 Class B Line Conducted Emission Limits: Quasi Peak Limits (db µ V) Average 0.15 to to to to to Note 1: The lower limits shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to.50mhz. Table 2 - Limits of conducted common mode (asymmetric mode) disturbance at telecommunication ports in the frequency range 0.15 MHz to 30 MHz for class B equipment. Frequency range (MHz) Voltage limits db(µv) Current limits db(µa) Quasi-peak Average Quasi-peak Average 0.15 to to to to to to Note 1: The limits decrease linearly with the logarithm of the frequency in the range 0.15 to 0.5 MHz. Note 2: The current and voltage disturbance limits are derived for use with an impedance stabilization network (ISN) which presents a common mode (asymmetric mode) impedance of 150Ω to the telecommunication under test (conversion factor is 20 log10 150/1 = 44dB). TEL: FAX: Page No. : 11 of 96

12 4.2. Test Procedures a. The EUT was placed on a desk 0.8 meters height from the metal ground plane and 0.4 meter from the conducting wall of the shielding room and it was kept at least 0.8 meters from any other grounded conducting surface. b. Connect EUT to the power mains through a line impedance stabilization network (LISN). c. All the support units are connecting to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The CISPR states that a 50 ohm, 50 micro-henry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The frequency range from 150 khz to 30 MHz was searched h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode Typical Test Setup 10cm EUT 80cm 80cm AE 80cm LISN ISN 40cm LISN 40cm TEL: FAX: Page No. : 12 of 96

13 4.4. Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. Test Receiver R&S ESCI AMN R&S ESH2-Z Two-Line V-Network R&S ENV ISN FCC FCC-TLISN-T ISN FCC FCC-TLISN-T ISN FCC FCC-TLISN-T ISN TESEQ ISN ST Current Probe R&S EZ Passive Voltage Probe R&S ESH2-Z Attenuator R&S ESH3-Z Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 13 of 96

14 4.5. Test Data and Result Test Mode : Mode 1: Normal Operation with ADS-65LSI G Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : LINE Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 14 of 96

15 Test Mode : Mode 1: Normal Operation with ADS-65LSI G Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : NEUTRAL Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 15 of 96

16 Test Mode : Mode 2: Normal Operation with FSP120-AFA Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : LINE Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 16 of 96

17 Test Mode : Mode 2: Normal Operation with FSP120-AFA Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : NEUTRAL Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 17 of 96

18 Test Mode : Mode 3: Normal Operation with FSP120-AFA+ ADS-65LSI G Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : LINE Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 18 of 96

19 Test Mode : Mode 3: Normal Operation with FSP120-AFA+ ADS-65LSI G Product: Network Video Model: DH-NVR5232-P Recorder AC Power : AC 230V/50Hz Phase : NEUTRAL Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 19 of 96

20 Test Mode : Mode 1: Normal Operation for LAN Port(10Mbps) Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Phase : LAN 10Mbps Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 20 of 96

21 Test Mode : Mode 2: Normal Operation for LAN Port(100Mbps) Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Phase : LAN 100Mbps Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 21 of 96

22 Test Mode : Mode 3: Normal Operation for LAN Port(1000Mbps) Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Phase : LAN 1000Mbps Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 22 of 96

23 Test Mode : Mode 4: Normal Operation for POE LAN Port(10Mbps) Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Phase : LAN 10Mbps Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 23 of 96

24 Test Mode : Mode 5: Normal Operation for POE LAN Port(100Mbps) Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Phase : LAN 100Mbps Temperature : 22 C Humidity : 50% Pressure(mbar) : 1002 Date: 2013/03/04 No. Frequency Factor Reading Level Limit Margin Detector (MHz) (db) (dbuv) (dbuv) (dbuv) (db) QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Note: Measurement Level = Reading Level + Correct Factor Test engineer: TEL: FAX: Page No. : 24 of 96

25 4.6. Test Photographs Main Port: Mode 1 Front View Rear View TEL: FAX: Page No. : 25 of 96

26 Main Port: Mode 2 Front View Rear View TEL: FAX: Page No. : 26 of 96

27 Main Port: Mode 3 Front View Rear View TEL: FAX: Page No. : 27 of 96

28 LAN Port: 10MHz&100MHz Front View Rear View TEL: FAX: Page No. : 28 of 96

29 LAN Port: 1000MHz Front View Rear View TEL: FAX: Page No. : 29 of 96

30 5. Test of Radiated Emission 5.1. Test Limit The EUT shall meet the limits of below Table when measured at the measuring distance R in accordance with the methods described in European Standard EN If the reading on the measuring receiver shows fluctuations close to the limit, the reading shall be observed for at least 15 s at each measurement frequency; the highest reading shall be recorded, with the exception of any brief isolated high reading, which shall be ignored. Table Limits for radiated disturbance of class B ITE at a measuring distance of 10 m Frequency range Quasi-peak limits MHz db(µv/m) 30 to to NOTE 1 The lower limit shall apply at the transition frequency. NOTE 2 Additional provisions may be required for cases where interference occurs. The EUT shall meet the limits of below Table when measured in accordance with the method described in European Standard EN and the conditional testing procedure described below. Table Limits for radiated disturbance of class B ITE at a measuring distance of 3 m Frequency range GHz Average limit db(µv/m) 1 to to NOTE The lower limit applies at the transition frequency. Peak limits db(µv/m) Conditional testing procedure: The highest internal source of an EUT is defined as the highest frequency generated or used within the EUT or on which the EUT operates or tunes. If the highest frequency of the internal sources of the EUT is less than 108 MHz, the measurement shall only be made up to 1 GHz. If the highest frequency of the internal sources of the EUT is between 108 MHz and 500 MHz, the measurement shall only be made up to 2 GHz. If the highest frequency of the internal sources of the EUT is between 500 MHz and 1 GHz, the measurement shall only be made up to 5 GHz. If the highest frequency of the internal sources of the EUT is above 1 GHz, the measurement shall be made up to 5 times the highest frequency or 6 GHz, whichever is less. TEL: FAX: Page No. : 30 of 96

31 5.2. Test Procedures a. The EUT was placed on a relatable table top 0.8 meter above ground. b. The EUT was set 10 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. c. The table was rotated 360 degrees to determine the position of the highest radiation. d. The antenna is a half wave dipole and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. e. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. f. Set the test-receiver system to Peak Detect Function and specified bandwidth with Maximum Hold Mode. TEL: FAX: Page No. : 31 of 96

32 5.3. Typical test Setup Below 1GHz Test Setup Above 1GHz Test Setup TEL: FAX: Page No. : 32 of 96

33 5.4. Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. EMI Test Receiver R&S ESCI Preamplifier Agilent 87405B My Preamplifier Agilent 8449B 3008A Ultra Broadband Antenna Broad-Band Horn Antenna R&S HL Schwarzbeck BBHA9120D 9120D Spectrum Analyzer R&S FSP Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 33 of 96

34 5.5. Test Result and Data 5.6. Test Result and Data (30MHz ~ 1000MHz) Test Mode : Mode 1: Normal Operation Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Ant. Polarization: Horizontal Temp : 23 Humidity : 52% Pressure(mbar) : 1002 Date : 2013/03/04 No. Frequency (MHz) Factor (db/m) Reading (dbuv) Level (dbuv/m) Limit (dbuv/m) Margin (db) Det. Height (cm) Azimuth (deg) QP QP QP QP QP QP Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 34 of 96

35 Test Mode : Mode 1: Normal Operation Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Ant. Polarization: Vertical Temp : 23 Humidity : 52% Pressure(mbar) : 1002 Date : 2013/03/04 No. Frequency (MHz) Factor (db/m) Reading (dbuv) Level (dbuv/m) Limit (dbuv/m) Margin (db) Det. Height (cm) Azimuth (deg) QP QP QP QP QP QP Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 35 of 96

36 5.7. Test Result and Data (1000MHz ~ 6000MHz) Test Mode : Mode 1: Normal Operation Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Ant. Polarization: Horizontal Temp : 23 Humidity : 52% Pressure(mbar) : 1002 Date : 2013/03/04 No. Frequency (MHz) Factor (db/m) Reading (dbuv) Level (dbuv/m) Limit (dbuv/m) Margin (db) Det. Height (cm) Azimuth (deg) peak AVG peak AVG peak AVG peak AVG peak AVG peak AVG Note: Measurement Level = Reading Level + Correct Factor TEL: FAX: Page No. : 36 of 96

37 Test Mode : Mode 1: Normal Operation Product: Network Video Recorder Model: DH-NVR5232-P AC Power : AC 230V/50Hz Ant. Polarization: Vertical Temp : 23 Humidity : 52% Pressure(mbar) : 1002 Date : 2013/03/04 No. Frequency (MHz) Factor (db/m) Reading (dbuv) Level (dbuv/m) Limit (dbuv/m) Margin (db) Det. Height (cm) Azimuth (deg) peak AVG peak AVG peak AVG peak AVG peak AVG peak AVG Note: Measurement Level = Reading Level + Correct Factor Test engineer: TEL: FAX: Page No. : 37 of 96

38 5.8. Test Photographs (30MHz ~ 1000MHz) Front View Rear View TEL: FAX: Page No. : 38 of 96

39 5.9. Test Photographs (1000MHz ~ 6000MHz) Front View Rear View TEL: FAX: Page No. : 39 of 96

40 6. Harmonics Test 6.1. Limits of Harmonics Current Measurement Limits for Class A equipment Limits for Class D equipment Harmonics Order n Max. Permissible harmonics current A Harmonics Order n Max. Permissible harmonics current per watt ma/w Max. Permissible harmonics current A Odd harmonics <=n<= /n Even harmonics Odd Harmonics only <=n<= /n 0.15 x15/n <=n<= /n 6.2. Measurement equipment Calibration Instrument/Ancillary Manufacturer Model No. Serial No. Valid Date. Date EMC Emission Tester EMCPARTNE Harmonics R Temperature/ Zhicheng ZC1-11 CEP-TH Humidity Meter TEL: FAX: Page No. : 40 of 96

41 6.3. Test Result and Data Basic Standard : EN Final Test Result : PASS Test Mode : Mode 1: Normal Operation Equipment : Network Video Recorder Model No. : DH-NVR5232-P Temperature : 22 Humidity : 50 % Atmospheric Pressure : 100 kpa Test Data : Mar 04, 2013 Full Bar : Actual Values Empty Bar : Maximum Values Blue : Current, Green : Voltage, Red : Failed Urms = 229.3V Freq = Range: 1 A Irms = 0.151A Ipk = 0.676A cf = P = 12.84W S = 34.71VA pf = THDi = 85.1 % THDu = 1.70 % Class A Test - Time : 15min ( 100 %) Test completed, Result: PASSED TEL: FAX: Page No. : 41 of 96

42 Order Freq. Irms Irms%L Imax Imax%L Limit [Hz] [A] [%] [A] [%] [A] EUT is PASSED if: - all Average values of the Individual Harmonic Currents (Iavg) are below 100% of the Individual Limits. - all Maximum values of the Individual Harmonic Currents (Imax) are below 150% of the Individual Limits. Test engineer: TEL: FAX: Page No. : 42 of 96

43 6.4. Test Photographs TEL: FAX: Page No. : 43 of 96

44 7. Voltage Fluctuations Test 7.1. Test Procedure The equipment shall be tested under the conditions of Clause 5. The total impedance of the test circuit, excluding the appliance under test, but including the internal impedance of the supply source, shall be equal to the reference impedance. The stability and tolerance of the reference impedance shall be adequate to ensure that the overall accuracy of ±8% is achieved during the whole assessment procedure Measurement equipment Calibration Instrument/Ancillary Manufacturer Model No. Serial No. Valid Date. Date EMC Emission Tester EMCPARTNE Harmonics R Temperature/ Zhicheng ZC1-11 CEP-TH Humidity Meter TEL: FAX: Page No. : 44 of 96

45 7.3. Test Result and Data Basic Standard : EN Final Test Result : PASS Test Mode : Mode 1: Normal Operation Equipment : Network Video Recorder Model No. : DH-NVR5232-P Temperature : 22 Humidity : 50 % Atmospheric Pressure : 100 kpa Test Data : Mar 05,2013 Full Bar : Actual Values Empty Bar : Maximum Values Circles : Average Values Blue : Current, Green : Voltage, Red : Failed TEL: FAX: Page No. : 45 of 96

46 Urms = 227.9V Freq = Range: 1 A Irms = 0.150A Ipk = 0.660A cf = P = 12.79W S = 34.17VA pf = Test - Time : 1 x 10min = 10min ( 100 %) LIN (Line Impedance Network) : No LIN Limits : Plt : 0.65 Pst : 1.00 dmax : 4.00 % dc : 3.30 % dtlim: 3.30 % dt>lim: 500ms Test completed, Result: PASSED Test engineer: TEL: FAX: Page No. : 46 of 96

47 7.4. Test Photographs TEL: FAX: Page No. : 47 of 96

48 8. Electrostatic Discharge Immunity Test 8.1. Test Procedure a. In the case of air discharge testing the climatic conditions shall be within the following ranges: - ambient temperature: 15 to 35 ; - relative humidity : 30% to 60%; - atmospheric pressure : 86 KPa (860 hpa) to 106 KPa (1060 hpa). b. Test programs and software shall be chosen so as to exercise all normal modes of operation of the EUT. The use of special exercising software is encouraged, but permitted only where it can be shown that the EUT is being comprehensively exercised. c. The test voltage shall be increased from the minimum to the selected test severity level, in order to determine any threshold of failure. The final severity level should not exceed the product specification value in order to avoid damage to the equipment. d. The test shall be performed with both air discharge and contact discharge. On reselected points at least 10 single discharges (in the most sensitive polarity) shall be applied on air discharge. On reselected points at least 25 single discharges (in the most sensitive polarity) shall be applied on contact discharge. e. For the time interval between successive single discharges an initial value of one second is recommended. Longer intervals may be necessary to determine whether a system failure has occurred. f. In the case of contact discharges, the tip of the discharge electrode shall touch the EUT before the discharge switch is operated. g. In the case of painted surface covering a conducting substrate, the following procedure shall be adopted : If the coating is not declared to be an insulating coating by the equipment manufacturer, then the pointed tip of the generator shall penetrate the coating so as to make contact with the conducting substrate. Coating declared as insulating by the manufacturer shall only be submitted to the air discharge. The contact discharge test shall not be applied to such surfaces. h. In the case of air discharges, the round discharge tip of the discharge electrode shall be approached as fast as possible (without causing mechanical damage) to touch the EUT. After each discharge, the ESD generator (discharge electrode) shall be removed from the EUT. The generator is then retriggered for a new single discharge. This procedure shall be repeated until the discharges are completed. In the case of an air discharge test, the discharge switch, which is used for contact discharge, shall be closed. TEL: FAX: Page No. : 48 of 96

49 8.2. Test Setup for Tests Performed in Laboratory The test setup consists of the test generator, EUT and auxiliary instrumentation necessary to perform DIRECT and INDIRECT application of discharges to the EUT as applicable, in the follow manner : a. Contact Discharge to the conductive surfaces and to coupling plane; b. Air Discharge at insulating surfaces. The preferred test method is that of type tests performed in laboratories and the only accepted method of demonstrating conformance with this standard. The EUT was arranged as closely as possible to arrangement in final installed conditions. A ground reference plane was provided on the floor of the test site. It was a metallic sheet (copper or aluminum) of 0.25 mm, minimum thickness; other metallic may be used but they shall have at least 0.65 mm thickness. In the Exclusive Certification Corp., we provided 1 mm thickness stainless steel ground reference plane. The minimum size of the ground reference plane is 2.5 m x 2.5 m, the exact size depending on the dimensions of the EUT. It was connected to the protective grounding system. The EUT was arranged and connected according to its functional requirements. A distance of 1m minimum was provided between the EUT and the wall of the lab. and any other metallic structure. In cases where this length exceeds the length necessary to apply the discharges to the selected points, the excess length shall, where possible, be placed non-inductively off the ground reference plane and shall not come closer than 0.2m to other conductive parts in the test setup. Where the EUT is installed on a metal table, the table was connected to the reference plane via a cable with a 470k ohm resister located at each end, to prevent a build-up of charge. The test setup was consist a wooden table, 0.8m high, standing on the ground reference plane. A HCP, 1.6 m x 0.8 m, was placed on the table. The EUT and cables was isolated from the HCP by an insulating support 0.5 mm thick. The VCP size, 0.5 m x 0.5 m. TEL: FAX: Page No. : 49 of 96

50 8.3. Test Severity Levels Contact Discharge Air Discharge Level Test Voltage (KV) of Level Test Voltage (KV) of Contact discharge Air Discharge 1 ±2 1 ±2 2 ±4 2 ±4 3 ±6 3 ±8 4 ±8 4 ±15 X Specified X Specified Remark: X is an open level Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. ESD Simulator EM Test dito V ESD Simulator Tonometer EMC PARTNER shanghaifengy un ESD DYM Dehumidifier ZEDO ZD-220LB CEP-TH-01 N/A N/A Humidifier YADU YZ-DS251C CEP-TH-02 N/A N/A Temperature/ Humidity Meter feiyan N/A TEL: FAX: Page No. : 50 of 96

51 8.5. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN : 2010 Equipment Model No. : Network Video Recorder : DH-NVR5232-P Final Test Result : PASS Temperature : 20 C Relative Humidity : 50% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN 55024: 2010 Test Mode 1 Contact Discharge Air Discharge 25 times / each 10 times / each Voltage 2 kv 4 kv 6 kv 8 kv 2 kv 4 kv 8 kv 10 kv Point\Polarity HCP A A A A VCP A A A A Screw A A A A Case A A A A A A Button A A A A A A Light A A A A A A VGA Port A A A A A A RS232 Port A A A A A USB Port A A A A A A Power Port A A A A A A TEL: FAX: Page No. : 51 of 96

52 For EN : 2011 Test Voltage: 230V/50Hz Contact Discharge Air Discharge 25 times / each 10 times / each Voltage 2 kv 4 kv 6 kv 8 kv 2 kv 4 kv 8 kv 10 kv Point\Polarity HCP A A A A A A VCP A A A A A A Screw A A A A A A Case A A A A A A Button A A A A A A Light A A A A A A VGA Port A A A A A A RS232 Port A A A A A A USB Port A A A A A A Power Port A A A A A A Test Voltage: 195.5V/50Hz Contact Discharge Air Discharge 25 times / each 10 times / each Voltage 2 kv 4 kv 6 kv 8 kv 2 kv 4 kv 8 kv 10 kv Point\Polarity HCP A A A A A A VCP A A A A A A Screw A A A A A A Case A A A A A A Button A A A A A A Light A A A A A A VGA Port A A A A A A RS232 Port A A A A A A USB Port A A A A A A Power Port A A A A A A TEL: FAX: Page No. : 52 of 96

53 Test Voltage:253V/50Hz Contact Discharge Air Discharge 25 times / each 10 times / each Voltage 2 kv 4 kv 6 kv 8 kv 2 kv 4 kv 8 kv 10 kv Point\Polarity HCP A A A A A A VCP A A A A A A Screw A A A A A A Case A A A A A A Button A A A A A A Light A A A A A A VGA Port A A A A A A RS232 Port A A A A A A USB Port A A A A A A Power Port A A A A A A Test engineer: TEL: FAX: Page No. : 53 of 96

54 8.6. Test Photographs TEL: FAX: Page No. : 54 of 96

55 9. Radio Frequency electromagnetic field immunity test 9.1. Test Procedure a. The equipment to be tested is placed in the center of the enclosure on a wooden table. The equipment is then connected to power and signal leads according to pertinent installation instructions. b. The required field strength is determined by placing the field strength meter(s) on top of or directly alongside the equipment under test and monitoring the field strength meter via a remote field strength indicator outside the enclosure while adjusting the continuous-wave to the applicable antennae. c. The test is normally performed with the antenna facing the most sensitive side of the EUT. The polarization of the field generated by the bucolical antenna necessitates testing each position twice, once with the antenna positioned vertically and again with the antenna positioned horizontally. The circular polarization of the field from the log-spiral antenna makes a change of position of the antenna unnecessary. d. At each of the above conditions, the frequency range is swept MHz, pausing to adjust the R.F. signal level or to switch oscillators and antenna. The rate of sweep is in the order of 1.5*10-3 decades/s. The sensitive frequencies or frequencies of dominant interest may be discretely analyzed. TEL: FAX: Page No. : 55 of 96

56 9.2. Test Severity Levels Condition of Test Remarks 1. Field Strength 10 V/m 2. Radiated Signal AM 80% Modulated with 1kHz Pulse modulation 1Hz (0.5s ON; 0.5s OFF) 3. Scanning Frequency 80MHz MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 9.3. Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. Signal Generator R&S SML Power Sensor R&S NR P-Z Power Sensor R&S NRP-Z Power Meter R&S NRP Power Amplifer BONN BLWA /100/40D Istropic Electric Field Probe EST.LINDGRE N HI EMS Antenna R&S HL046E N/A N/A Temperature/ Humidity Meter feiyan N/A TEL: FAX: Page No. : 56 of 96

57 9.4. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN : 2010 Equipment : Network Video Recorder Model No. : DH-NVR5232-P Final Test Result : PASS Temperature : 23 C Relative Humidity : 52% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN 55024: 2010 Test Mode 1 Modulation : AM 80%, 1KHz sine wave, Dwell time: 3.0 S Frequency Step Size : 1 % of preceding frequency value Frequency (MHz) Antenna Polarization face Field strength (V/m) Result 80~1000 Vertical Front 3 V/m A 80~1000 Vertical Rear 3 V/m A 80~1000 Vertical Left 3 V/m A 80~1000 Vertical Right 3 V/m A 80~1000 Horizontal Front 3 V/m A 80~1000 Horizontal Rear 3 V/m A 80~1000 Horizontal Left 3 V/m A 80~1000 Horizontal Right 3 V/m A TEL: FAX: Page No. : 57 of 96

58 For EN : 2011 Test Voltage: 230V/50Hz Test Mode 1: Normal Operation Modulation : AM 80%, 1KHz sine wave, Dwell time: 3.0 S Frequency Step Size : 1 % of preceding frequency value Frequency (MHz) Antenna Polarization face Field strength (V/m) Result 80~2700 Horizontal &Vertical Front 10 V/m A 80~2700 Horizontal &Vertical Rear 10 V/m A 80~2700 Horizontal &Vertical Left 10 V/m A 80~2700 Horizontal &Vertical Right 10 V/m A Test Voltage: 195.5V/50Hz Test Mode 1: Normal Operation Modulation : AM 80%, 1KHz sine wave, Dwell time: 3.0 S Frequency Step Size : 1 % of preceding frequency value Frequency (MHz) Antenna Polarization face Field strength (V/m) Result 80~2700 Horizontal &Vertical Front 10 V/m A 80~2700 Horizontal &Vertical Rear 10 V/m A 80~2700 Horizontal &Vertical Left 10 V/m A 80~2700 Horizontal &Vertical Right 10 V/m A Test Voltage: 253V/50Hz Test Mode 1: Normal Operation Modulation : AM 80%, 1KHz sine wave, Dwell time: 3.0 S Frequency Step Size : 1 % of preceding frequency value Frequency (MHz) Antenna Polarization face Field strength (V/m) Result 80~2700 Horizontal &Vertical Front 10 V/m A 80~2700 Horizontal &Vertical Rear 10 V/m A 80~2700 Horizontal &Vertical Left 10 V/m A 80~2700 Horizontal &Vertical Right 10 V/m A Test engineer: TEL: FAX: Page No. : 58 of 96

59 9.5. Test Photographs TEL: FAX: Page No. : 59 of 96

60 10. Electrical Fast Transient/ Burst Immunity Test Test Procedure a. In order to minimize the effect of environmental parameters on test results, the climatic conditions when test is carrying out shall comply with the following requirements: ambient temperature: 15 to 35 ; relative humidity : 45% to 75%; Atmospheric pressure: 86 Kpa (860 hpa) to 106 Kpa (1060 hpa). b. In order to minimize the effect of environmental parameters on test results, the electromagnetic environment of the laboratory shall not influence the test results. c. The variety and diversity of equipment and systems to be tested make it difficult to establish general criteria for the evaluation of the effects of fast transients/bursts on equipment and systems. d. Test on Power Line: The EFT/B-generator was located on the GRP.. The length from the EFT/B-generator to the EUT is not exceeding 1 m. The EFT/B-generator provides the ability to apply the test voltage in a non-symmetrical condition to the power supply input terminals of the EUT. e. Test on Communication Lines The coupling clamp is composed of a clamp unit for housing the cable (length more than 3 m), and was placed on the GRP. The coupling clamp provides the ability of coupling the fast transient/bursts to the cable under test. f. The test results may be classified on the basic of the operating conditions and the functional specification of the equipment under test, according to the following performance criteria : Normal performance within the specification limits. Temporary degradation or loss of function or performance which is self-recoverable. Temporary degradation or loss of function or performance which requires operator intervention or system reset. Degradation or loss of function which is not recoverable due to damage of equipment (components). TEL: FAX: Page No. : 60 of 96

61 10.2. Test Severity Levels The following test severity levels are recommended for the fast transient/burst test : Open circuit output test voltage ± 10% Level On Power Supply On I/O signal, data and control line KV 0.25 KV KV 0.50 KV KV 1.00 KV KV 2.00 KV X Specified Specified Remark : X is an open level. The level is subject to negotiation between the user and the manufacturer or is specified by the manufacturer Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. TRANSIENT EMCPARTNER TRA2000IN CDN EMCPARTNER CDN Coupling clamp EMCPARTNER CN-EFT Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 61 of 96

62 10.4. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN 55024: 2010 Equipment Model No. : Network Video Recorder : DH-NVR5232-P Final Test Result : PASS Temperature : 21 C Relative Humidity : 51% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN : 2010 Test Mode 1& Test Mode 2 Pulse : 5/50 ns Burst : 15m/300ms Repetition Rate: 5 khz above 2.0 kv 5 khz below and equal 2.0 kv Test time : 1 min/each condition Voltage/ Mode/ Polarity/ Result/ Phase 0.5 kv 1.0 kv L A A N A A L-N A A Power Line PE A A L-PE A A N-PE A A L-N-PE A A Signal Line RJ 45 A A TEL: FAX: Page No. : 62 of 96

63 For EN : 2011 Test Mode 1& Test Mode 2 Test Voltage:230V/50Hz Test Mode 1: Normal Operation Pulse : 5/50 ns Burst : 15m/300ms Test time : 1 min/each condition Voltage/ Mode/ Polarity/ Result/ Phase Repetition Rate: 5 khz /100 khz above 2.0 kv 1.0 kv 2.0 kv L A A N A A L-N A A Power Line PE A A L-PE A A N-PE A A L-N-PE A A Signal Line RJ 45 A A Test Mode 1& Test Mode 2 Test Voltage:195.5V/50Hz Test Mode 1: Normal Operation Pulse : 5/50 ns Burst : 15m/300ms Test time : 1 min/each condition Voltage/ Mode/ Polarity/ Result/ Phase Repetition Rate: 5 khz /100 khz above 2.0 kv 1.0 kv 2.0 kv L A A N A A L-N A A Power Line PE A A L-PE A A N-PE A A L-N-PE A A Signal Line RJ 45 A A TEL: FAX: Page No. : 63 of 96

64 Test Mode 1& Test Mode 2 Test Voltage:253V/50Hz Test Mode 1: Normal Operation Pulse : 5/50 ns Burst : 15m/300ms Test time : 1 min/each condition Voltage/ Mode/ Polarity/ Result/ Phase Power Line Repetition Rate: 5 khz /100 khz above 2.0 kv 1 kv 2.0 kv L A A N A A L-N A A PE A A L-PE A A N-PE A A L-N-PE A A Signal Line RJ 45 A A Test engineer: TEL: FAX: Page No. : 64 of 96

65 10.5. Test Photographs Main Port LAN Port TEL: FAX: Page No. : 65 of 96

66 POE LAN Port TEL: FAX: Page No. : 66 of 96

67 11. Surge Immunity Test Test Procedure a. Climatic conditions The climatic conditions shall comply with the following requirements : ambient temperature : 15 to 35 relative humidity : 10 % to 75 % atmospheric pressure : 86 kpa to 106 kpa ( 860 hpa to 1060 hpa ) b. Electromagnetic conditions the electromagnetic environment of the laboratory shall not influence the test results. c. The test shall be performed according the test plan that shall specify the test set-up with generator and other equipment utilized; test level ( voltage/current ); generator source impedance; internal or external generator trigger; number of tests : at least five positive and five negative at the selected points; repetition rate : maximum 1/min. inputs and outputs to be tested; representative operating conditions of the EUT; sequence of application of the surge to the circuit; phase angle in the case of AC. power supply; actual installation conditions, for example : AC : neutral earthed, DC : ( + ) or ( - ) earthed to simulated the actual earthing conditions. d. If not otherwise specified the surges have to be applied synchronized to the voltage phase at the zero-crossing and the peak value of the AC. voltage wave ( positive and negative ). e. The surges have to be applied line to line and line(s) and earth. When testing line to earth, the test voltage has to be applied successively between each of the lines and earth, if there is no other specification. f. The test procedure shall also consider the non-linear current-voltage characteristics of the equipment under test. Therefore the test voltage has to be increased by steps up to the test level specified in the product standard or test plan. g. All lower levels including the selected test level shall be satisfied. For testing the secondary protection, the output voltage of the generator shall be increased up to the worst-case voltage breakdown level ( let-through level ) of the primary protection. h. If the actual operating signal sources are not available, that may be simulated. Under no circumstances may the test level exceed the product specification. The test shall be carried out according to a test plan. i. To find all critical points of the duty cycle of the equipment, a sufficient number of positive and negative test pulses shall be applied. For acceptance test previously unstressed equipment shall be used to the protection devices shall be replaced. TEL: FAX: Page No. : 67 of 96

68 11.2. Test Severity Level Level Open-circuit test voltage, ± 10%, KV X Specified NOTE: X is an open class. This level can be specified in the product specification Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. TRANSIENT EMCPARTNER TRA2000IN CDN EMCPARTNER CDN-UTP CDN EMCPARTNER CDN Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 68 of 96

69 11.4. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN : 2010 Equipment : Network Video Recorder Model No. : DH-NVR5232-P Final Test Result : PASS Temperature : 21 C Relative Humidity : 51% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN 55024: 2010 Power Port Test Mode 1& Test Mode 2 Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 20 time/each condition /Phase Voltage / Mode / Polarity / Result /1.0 kv L-N + A A A A - A A A A 0.5/1.0/2.0kV L-PE N-PE + A A A A - A A A A + A A A A - A A A A Waveform : 10/700µs Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B TEL: FAX: Page No. : 69 of 96

70 For EN : 2011 Power Port Test Mode 1& Test Mode 2 Test Voltage:230V/50Hz Test Mode 1 Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 20 time/each condition /Phase Voltage / Mode / Polarity / Result /1.0 kv L-N + A A A A - A A A A 0.5/1.0/2.0kV L-PE N-PE + A A A A - A A A A + A A A A - A A A A Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B Waveform : 10/700µs Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B TEL: FAX: Page No. : 70 of 96

71 Power Port Test Mode 1& Test Mode 2 Test Voltage:195.5V/50Hz Test Mode 1 Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 20 time/each condition /Phase Voltage / Mode / Polarity / Result /1.0 kv L-N + A A A A - A A A A 0.5/1.0/2.0kV L-PE N-PE + A A A A - A A A A + A A A A - A A A A Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B Waveform : 10/700µs Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B TEL: FAX: Page No. : 71 of 96

72 Power Port Test Mode 1& Test Mode 2 Test Voltage:253V/50Hz Test Mode 1 Waveform : 10/700µs Repetition rate : 60 sec Time : 20 time/each condition /Phase Voltage / Mode / Polarity / Result /1.0 kv L-N + A A A A - A A A A 0.5/1.0/2.0kV L-PE N-PE + A A A A - A A A A + A A A A - A A A A Waveform : 1.2/50µs(8/20µs) Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B Waveform : 10/700µs Repetition rate : 60 sec Time : 5 time/each condition Voltage 0.5 kv 1 kv Mode / Polarity / Result RJ45 B B B B Test engineer: TEL: FAX: Page No. : 72 of 96

73 11.5. Test Photographs Main Port LAN Port TEL: FAX: Page No. : 73 of 96

74 POE LAN Port TEL: FAX: Page No. : 74 of 96

75 12. Conduction Disturbances induced by Radio-Frequency Fields Test Procedure a. The EUT shall be operated within its intended climatic conditions. The temperature and relative humidity should be recorded. b. This test method test can be performed without using a sell shielded enclosure. This is because the disturbance levels applied and the geometry of the setups are not likely to radiated a high amount of energy, especially at the lower frequencies. If under certain circumstances the radiated energy is too high, a shielded enclosure has to be used. c. The test shall be performed with the test generator connected to each of the coupling and decoupling devices in turn while the other non-excited RF-input ports of the coupling devices are terminated by a 50 ohm load resistor. d. The frequency range is swept from 150 KHz to 100 MHz, using the signal levels established during the setting process, and with the disturbance signal 80% amplitude modulated with a 1KHz sign wave, pausing to adjust the RF-signal level or to switch coupling devices as necessary. The rate of sweep shall no exceed 1.5 x 10-3 decades/s. Where the frequency is swept incrementally, the step size shall no exceed 1% of the start and thereafter 1% of the preceding frequency value. e. The dwell time at each frequency shall not be less than the time necessary for the EUT to be exercised, and able to respond. Sensitive frequencies e.g. clock frequency (ies) and harmonics or frequencies of dominant interest shall be analyzed separately. f. An alternative test procedure may be adopted, wherein the frequency range is swept incrementally, with a step size not exceeding 4% of the start ad thereafter 4% of the preceding frequency value. The test level should be at least twice the value of the specified test level. g. In cases of dispute, the test procedure using a step size not exceeding 1% of the start and thereafter 1% of preceding frequency value shall take precedence. h. Attempts should be made to fully exercise the EUT during testing, and to fully interrogate all exercise modes selected for susceptibility. i. The use of special exercising programs is recommended. j. Testing shall be performed according to a Test Plan, which shall be included in the test report. k. It may be necessary to carry out some investigatory testing in order to establish some aspects of the test plan. TEL: FAX: Page No. : 75 of 96

76 12.2. Test Severity Levels Level Voltage Level ( EMF ), 1 1 V 2 3 V 3 10 V x Specified NOTE - x is an open class. This level can be specified in the product specification Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Conducted immunity test system Calibration Date Valid Date. FRANKONIA CIT-10/75 102D EM Injection clamp FCC F-203I-23MM CDN FRANKONIA CDN-T2 A CDN FRANKONIA CDN-T4 A CDN FRANKONIA CDN-T8 A CDN FRANKONIA CDN-M2 A CDN FRANKONIA CDN-M2+M3 A CDN FCC CDN-M5/32 A db Attenuator FRANKONIA N/A N/A Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 76 of 96

77 12.4. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN : 2010 Equipment : Network Video Recorder Model No. : DH-NVR5232-P Final Test Result : PASS Temperature : 21 C Relative Humidity : 51% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN 55024: 2010 Test Mode 1& Test Mode 2 Frequency : 0.15~80MHz, Modulation : AM 80%,1KHz sine wave, Dwell time: 2.9s Frequency Step Size : 1 % of preceding frequency value Frequency Test mode Voltage(V) Result 0.15 ~ 80MHz Power(M3) 3 A 0.15 ~ 80MHz RJ45 3 A For EN : 2011 Test Voltage:230V/50Hz Test Mode 1& Test Mode 2 Test Mode 1: Normal Operation Frequency : 0.15~100MHz, Modulation : AM 80%,1KHz sine wave, Dwell time: 2.9s Frequency Step Size : 1 % of preceding frequency value Frequency Test mode Voltage(V) Result 0.15 ~ 100MHz Power(M3) 10 A 0.15 ~ 100MHz RJ45 10 A TEL: FAX: Page No. : 77 of 96

78 Test Voltage:195.5V/50Hz Test Mode 1& Test Mode 2 Test Mode 1: Normal Operation Frequency : 0.15~100MHz, Modulation : AM 80%,1KHz sine wave, Dwell time: 2.9s Frequency Step Size : 1 % of preceding frequency value Frequency Test mode Voltage(V) Result 0.15 ~ 100MHz Power(M3) 10 A 0.15 ~ 100MHz RJ45 10 A Test Voltage:253V/50Hz Test Mode 1& Test Mode 2 Test Mode 1: Normal Operation Frequency : 0.15~100MHz, Modulation : AM 80%,1KHz sine wave, Dwell time: 2.9s Frequency Step Size : 1 % of preceding frequency value Frequency Test mode Voltage(V) Result 0.15 ~ 100MHz Power(M3) 10 A 0.15 ~ 100MHz RJ45 10 A Test engineer: TEL: FAX: Page No. : 78 of 96

79 12.5. Test Photographs Main Port LAN Port TEL: FAX: Page No. : 79 of 96

80 POE LAN Port TEL: FAX: Page No. : 80 of 96

81 13. Power Frequency Magnetic Field Immunity Tests Test Setup GPR : Ground plane C1 : Power supply circuit A : Safety earth C2 : Signal circuit S : Insulating support L : Communication line EUT : Equipment under test B : To power supply source Lc : Induction coil D : To signal source, simulator E : Earth terminal G : To the test generator Test Severity Levels Level Magnetic field strength A/m X 1) special NOTE 1 X is an open level. This level can be givenin the product specification Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. TRANSIENT EMCPARTNER TRA2000IN H-Filed-Loop EMCPARTNER MF Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 81 of 96

82 13.4. Test Result and Data Basic Standard : IEC Product Standard : EN : 2010 Equipment : Network Video Recorder Model No. : DH-NVR5232-P Final Test Result : PASS Temperature : 21 C Relative Humidity : 51 % Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 Power Frequency Magnetic Field : 50 Hz, 1 A/m Coil Orientation Testing duration Results X-axis 1.0 Min A Y-axis 1.0 Min A Z-axis 1.0 Min A Test engineer: TEL: FAX: Page No. : 82 of 96

83 13.5. Test Photographs TEL: FAX: Page No. : 83 of 96

84 14. Voltage Dips and Voltage Interruptions Immunity Test Setup Test Conditions 1. Source voltage and frequency : 230V / 50Hz, Single phase. 2. Test of interval : 10 sec. 3. Level and duration : Sequence of 3 dips/interrupts. 4. Voltage rise (and fall) time : 1 5 µs. 5. Test severity : Voltage dips and Interrupt reduction (%) Test Duration (period) >95% % 25 >95% 0.5 Item Environmental Units Test Performance Phenomena Specification Criteria Input AC Power Ports Voltage Dips % Reduction 20 period 250 % Reduction 30 period 25 % Reduction 60 period 10 Voltage Interruptions % Reduction 100 period Measurement equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date. TRANSIENT EMCPARTNER TRA2000IN Temperature/ Humidity Meter Zhicheng ZC1-11 CEP-TH TEL: FAX: Page No. : 84 of 96

85 14.3. Test Result and Data Basic Standard : IEC Product Standard : EN : 2011 Product Standard : EN : 2010 Equipment Model No. Final Test Result : Network Video Recorder : DH-NVR5232-P : PASS Temperature : 21 C Relative Humidity : 51% Atmospheric Pressure : 100 kpa Test Date : Mar 05, 2013 For EN 55024: 2010 Mode 1 Test Voltage: 230V/50Hz Test Mode : Mode 1: Normal Operation Interval(s) : 10s Times : 3 Test mode Test level reduction % Durations (period / ms ) Phase / Result Voltage interrupt ions Voltage dips >95% 250 C C C C C C C C 30% 25 A A A A A A A A >95% 0.5 A A A A A A A A Mode 2 Test Voltage: 230V/50Hz Test Mode : Mode 1: Normal Operation Interval(s) : 10s Times : 3 Test level Durations Test reduction (period / mode % ms ) Phase / Result Voltage interrupt ions Voltage dips >95% 250 C C C C C C C C 30% 25 A A A A A A A A >95% 0.5 A A A A A A A A TEL: FAX: Page No. : 85 of 96

86 For EN : 2011 Test Voltage: 230V/50Hz Voltage(UT): AC 230 V 50 Hz Interval(s) : 10s Times : 3 Test mod Voltage interruptions Durations Phase / Result Test level (period / UT % ms ) 100% 250 C C C C C C C C 20% 250 C C C C C C C C Voltage dips 30% 25 A A A A A A A A 60% 10 A A A A A A A A Test Voltage: 195.5V/50Hz Voltage(UT): AC 230 V 50 Hz Interval(s) : 10s Times : 3 Test mod Voltage interruptions Durations Phase / Result Test level (period / UT % ms ) 100% 250 C C C C C C C C 20% 250 C C C C C C C C Voltage dips 30% 25 A A A A A A A A 60% 10 A A A A A A A A TEL: FAX: Page No. : 86 of 96

87 Test Voltage: 253V/50Hz Voltage(UT): AC 230 V 50 Hz Interval(s) : 10s Times : 3 Test mod Voltage interruptions Durations Phase / Result Test level (period / UT % ms ) 100% 250 C C C C C C C C 20% 250 C C C C C C C C Voltage dips 30% 25 A A A A A A A A 60% 10 A A A A A A A A Test engineer: TEL: FAX: Page No. : 87 of 96

88 14.4. Test Photographs TEL: FAX: Page No. : 88 of 96

89 15. EUT Photographs 1) EUT Photo 2) EUT Photo TEL: FAX: Page No. : 89 of 96

90 3) EUT Photo 4) EUT Photo TEL: FAX: Page No. : 90 of 96

91 5) EUT Photo 6) EUT Photo TEL: FAX: Page No. : 91 of 96

92 7) EUT Photo 8) EUT Photo (Adapter 1#) TEL: FAX: Page No. : 92 of 96

93 9) EUT Photo (Adapter 1#) 10) EUT Photo (Adapter 1#) TEL: FAX: Page No. : 93 of 96

94 11) EUT Photo (Adapter 1#) 12) EUT Photo (Adapter 2#) TEL: FAX: Page No. : 94 of 96

95 13) EUT Photo (Adapter 2#) 14) EUT Photo (Adapter 2#) TEL: FAX: Page No. : 95 of 96

96 15) EUT Photo (Adapter 2#) TEL: FAX: Page No. : 96 of 96