一前言感谢您购买我司产品, 如对本公司产品有疑问或需要, 请随时和我们联系我们尽最大努力来保证本手册信息的正确性, 如因升级等原因发生信息修改, 恕不另行通知获取最新文档请联系产品供应商二安全说明此内容 ( 手册 ) 的目的是确保用户正确使用本产品, 以避免危险或财产损失在使用产品之前,

Size: px

Start display at page:

Download "一前言感谢您购买我司产品, 如对本公司产品有疑问或需要, 请随时和我们联系我们尽最大努力来保证本手册信息的正确性, 如因升级等原因发生信息修改, 恕不另行通知获取最新文档请联系产品供应商二安全说明此内容 ( 手册 ) 的目的是确保用户正确使用本产品, 以避免危险或财产损失在使用产品之前,"

艇郎
4 years ago
Views:

3 一前言感谢您购买我司产品, 如对本公司产品有疑问或需要, 请随时和我们联系我们尽最大努力来保证本手册信息的正确性, 如因升级等原因发生信息修改, 恕不另行通知获取最新文档请联系产品供应商二安全说明此内容 ( 手册 ) 的目的是确保用户正确使用本产品, 以避免危险或财产损失在使用产品之前, 请认真阅读此手册并妥善保存以备日后参考如果用户因没有按照以下安全说明, 致使设备不能正常使用或损坏等情况, 责任由用户承担 1. 请使用满足安全电压要求的电源 2. 如果设备工作不正常, 请联系购买设备的商店 ( 厂家 ) 或最近的服务中心不要以任何方式随意拆卸或修改设备 3. 请防止此产品从高处摔落或受强烈敲击 4. 清洁镜头时, 请使用吹气球或专业镜头布除去镜头上的污垢清洁透明护罩时, 须使用足够柔软干燥的布清洁擦拭, 切勿使用含有酒精苯等的清洁剂进行洗涤 5. 避免将摄像机对准强光 ( 如灯光照明太阳光等处 ) 聚焦, 否则容易引起过亮或漏光现象 ( 这并非摄像机故障 ), 将影响摄像机寿命 6. 避免将产品暴露在非用户手册所示的工作环境下使用工作环境工作电源 DC12V±10% 温度 -40 ~60 湿度 10%~95%( 无凝结 ) 海拔高度 -60m~3000m 大气压 86kPa~106kPa 7. 使用时不可让水或任何液体流入摄像机 8. 当运送摄像机时, 请重新以出厂时的包装进行包装, 或用同等品质的材料包装 9. 需要替换部件时, 请事先与经销商联系, 更换指定型号的部件, 或与原部件具有相同特性的部件擅自使用其它部件进行替换, 后果自负 10. 本产品达到 IP66 防护等级, 工作于室外露天环境时, 请注意设备尾线的防水处理说明更多信息见附带光盘中的高清网络摄像机用户手册 1

4 三设备安装摄像机支持吊装壁装吸顶安装嵌入式安装墙面安装, 安装前请预先准备安装配件图 1 1. 使用定位模板在安装面上打孔, 将设备固定在支架或安装面上图 2 2. 线缆可从设备顶部或侧面穿出, 请根据需要选择侧面出线方法如下图 : 图 3 2

3. 完成线缆连接, 上电标签含义如图图 4 说明尾线接口请根据具体型号支持为准, 图 4 所示为接口最全的型号线缆识别请参考附录部分 4. 登录客户端最低配置和系统环境 : 处理器 :3.3 GHz 酷睿 i3 系列及以上或相同性能的其他处理器 RAM 内存 :4GB 及以上操作系统 :Windows XP 操作系统或更高版本浏览器 :IE7.

5 3. 完成线缆连接, 上电标签含义如图图 4 说明尾线接口请根据具体型号支持为准, 图 4 所示为接口最全的型号线缆识别请参考附录部分 4. 登录客户端最低配置和系统环境 : 处理器 :3.3 GHz 酷睿 i3 系列及以上或相同性能的其他处理器 RAM 内存 :4GB 及以上操作系统 :Windows XP 操作系统或更高版本浏览器 :IE7.0 及以上版本,Firefox,Google Chrome(41 及以下版本 ) DirectX:9.0c 1) 第一次使用时请运行光盘中附带的 IPCSearch, 在 IPCSearch 中将显示设备的 IP 地址网关等信息若 IPC 设备所接入的网络有 DHCP 服务,DHCP 服务器将自动给 IPC 分配 IP 地址 2) 在 IPCSearch 中选中设备, 点击, 在弹出的界面中设置 admin 用户的密码和找回密码时需要用的邮箱, 点击激活按钮激活设备待设备重启 3

6 图 5 3) 点击, 在弹出的界面中配置网络参数静态分配 IP 地址时, 请选择自定义地址, 填写以太网参数修改参数配置, 需要填写管理员用户用户名 (admin) 及激活设备时所设置的密码完成 IP 配置后, 设备将自动重启, 重启时间约为 60 秒 4) 在 IPCSearch 中双击设备或点击, 输入用户名和密码 ( 如图 6), 登录 Web 客户端图 6 4

7 说明如果直接通过 Web 端首次登录未激活的设备, 可在登录界面设置管理员的密码激活设备 ( 如图 7 ) 登录前需要先将 PC 机设置为与设备在同一网段图 7 5) 登录成功后, 下载并安装视频插件 5. 镜头调节和镜头调整进入客户端后可以直接浏览图像, 界面如图说明不同型号浏览界面略有差异, 请以设备实际界面为主更多客户端说明参见客户端帮助文档调整镜头角度对准目标区域, 完成后拧紧镜头座上的固定螺钉部分型号支持自动聚焦安装调试配备手动变焦手动光圈镜头的型号时, 调节镜头上旋钮或旋转镜头, 进行对焦或光圈调节说明请确认光圈调到最大, 再开始对焦和视野调节调整设备方向, 在 Web 客户端上进行参数调整, 直到浏览画面达到预定要求完成调节后, 合上球罩, 拧紧固定螺钉图 8 5

8 附录 : 线缆识别 1. -DN/EN 系列 2. -AN 系列线序标签标示颜色组别注释 1 TV_OUT+ 黑视频输出正极 2 TV_OUT- 棕视频输出负极 3 RS485_A 紫一组 RS485 串口 A 4 RS485_B 灰 RS485 串口 B 5 AUDIO_IN 黄音频输入 6 AUDIO_OUT 红音频输出 7 AUDIO_GND 橙一组音频接地 8 AUDIO_GND 白音频接地 9 ALARM_IN 1 白 / 橙告警输入 1 10 ALARM_IN 2 白 / 棕告警输入 2 11 ALARM_IN 3 白 / 红一组告警输入 3 12 ALARM_IN_GND 粉红告警输入接地 13 ALARM_OUT 1A 浅绿告警输出 1, 两个 14 ALARM_OUT 1B 白 / 黑端子不分正负 15 DC 12V_OUT+ 蓝直流 12V 输出正极一组 16 DC 12V_OUT- 绿直流 12V 输出负极线序标签标示颜色组别注释 1 TV_OUT+ 黑视频输出正极 2 TV_OUT- 棕视频输出负极 3 RS485_A 红一组 RS485 串口 A 4 RS485_B 橙 RS485 串口 B 5 AUDIO_IN 粉红音频输入 6 AUDIO_OUT 灰音频输出 7 AUDIO_GND 紫一组音频接地 8 AUDIO_GND 黄音频接地 9 ALARM_IN 1 浅绿告警输入 1 10 ALARM_IN_GND 白告警输入接地 11 ALARM_OUT 1A 绿一组告警输出 1, 两个 12 ALARM_OUT 1B 蓝端子不分正负 6

9 7

10 Preface Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact us. Every effort has been made to ensure the accuracy and validity of this Guide. Any update of this Guide is subject to change without notice. For the latest document, please contact the dealer. Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Please read this Guide carefully before using the product, and keep it properly for future reference. If the product cannot work normally or is damaged because the user does not follow the safety instructions, we shall not assume any responsibility. Please adopt power supply in the safety voltage range. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble or repair the product yourself in any way. Do not drop the camera or subject it to physical shock. When cleaning the lens, please use a rubber dust blower or lens cleaning cloth to remove the dirt. When cleaning transparent housing, please use soft and dry cleaning cloth to wipe it gently. Never apply any cleanser with ethanol or benzene in it Do not focus the camera lens on strong light such as the sun or incandescent lamp. The strong light can cause overexposure or light leak (not camera malfunction), which may shorten camera lifetime. Do not expose the camera in the environment not defined in the Guide. Operating Environment Working Voltage DC12V±10% Temperature -40 ~60 Humidity Altitude Atmospheric Pressure 10%~95% (non-condensing) -60m~3000m 86kPa~106kPa Keep the camera away from water or any liquid. While shipping the camera, pack it in the factory packing or use materials with equivalent quality. When it is necessary to replace a part, please contact your dealer in advance and replace the part with specified model or part of the same features. We shall not assume any responsibility for problems caused by unauthorized replacement. The camera is IP66-rated. When expose it outdoor, remember to handle with the back cable of the camera and make it water-proof. [Note]: For more information, please refer to the User Manual for HD IP Camera in the attached CD. 1

11 Installation Steps The camera supports ceiling bracket mount, wall bracket mount, ceiling mount, embedded mount and wall mount. Please get the accessories ready before installation. Please make the cable hole downward to prevent water. Ceiling Bracket Mount Wall Bracket Mount Ceiling Mount Embedded Mount Wall Mount Picture 1 1. Punch holes on the mounting surface with positioning board. Fix the device on the mounting surface or the bracket. Set Screw Picture 2 2. User can either route cables from the top or the side of the device according to the requirement. Side cabling is shown as below: 3 When route cable from side, use G3/4-14 thread tube for cabling. 1 Loosen screws 2 Take down the cover Picture 3 2

12 DC12V OUT DC12V IN KEDACOM KEDACOM KEDACOM PICKUP 3. After connecting cables, power on the device. Tag meanings are explained as follows: Connect to the devices shown on the tags RS485_A/B Connect to surveillance keyboard or alarm expander Cut off terminal cables ALA_OUT Alarm Output ALARM_IN1/2/3 Alarm Input LINE_OUT Audio Output LINE_IN Audio Input TV_OUT Video Output DC12V/50mA_OUT Power for pick-up and other devices. DC12V_IN Client 10/100M self-adaptive Picture 4 [Note]: Picture 4 illustrates how to connect devices to ports on a camera. However, the camera you purchased may not be equipped with all the preceding ports. For any query, please contact the dealer. 4. Login client Minimum configurations and system requirements: Processor: 3.3 GHz CORE i3 series or other equivalent processors RAM Memory: 4GB or above Operating System: Windows XP or newer version Browser: IE7.0 and newer version, Firefox, Google Chrome (41 and lower) DirectX:9.0c 1) When use the device for the first time, run the IPCSearch in the attached CD and camera IP address and gateway will show. If the network provides DHCP service, DHCP server will assign IP for the camera automatically. 2) Select the device and click Batch processing. In the popup interface, set admin user s password and the claim address to find back the password. Click Active and wait for rebooting. 3

Picture 5 3) Click Modify Params and set the network parameters.

During the modification, the admin user name (admin) and the password set during activation should be entered.

4) Double click the device in IPCSearch or click Login.

13 Picture 5 3) Click Modify Params and set the network parameters. When configure a static IP for the camera, please check Custom device address (Close DHCP) and fill the Ethernet parameter. During the modification, the admin user name (admin) and the password set during activation should be entered. After configuration, the camera will reboot automatically and this takes 60s. 4) Double click the device in IPCSearch or click Login. Enter user name and password (shown in Picture 9) to login to the web client. Picture 6 [Note]: If login the nonactivated camera by web client, you can set admin user s password on the login interface to activate the device (as in Picture 7). Before setting, set the PC and the device in the same LAN. 5) After login, download and install the plug-in. 4

Picture 7 5. Live view and lens adjustment After login, user can view live video directly, as the picture shows. [Note]: Interface of different models may differ.

When install and adjust cameras with manual focus and manual iris lens, adjust the lens knob or rotate the lens to adjust focus or aperture.

14 Picture 7 5. Live view and lens adjustment After login, user can view live video directly, as the picture shows. [Note]: Interface of different models may differ. Please refer to the help file for detailed explanation. Adjust camera angle to the target area, and then tighten the set screw on the lens holder. When install and adjust cameras with manual focus and manual iris lens, adjust the lens knob or rotate the lens to adjust focus or aperture. [Note]: Please make sure that the aperture is adjusted to the max before adjusting focus and field of view. Modify parameters through web client till meeting requirement. After adjustment, cover the dome housing and tighten the set screws. Picture 8 5

15 Cable Identification 1. -DN/EN Series N o. T a g C o l o r G ro u p R e m a rk s 1 TV-OUT+ BLACK Video Output + 2 TV-OUT- BROWN Video Output - Group 3 RS485_A PURPLE RS485 Serial Port A 4 RS485_B GREY RS485 Serial Port B 5 AUDIO_IN YELLOW Audio Input 6 AUDIO_OUT RED Audio Output Group 7 AUDIO_GND ORANGE Audio Grounding 8 AUDIO_GND WHITE Audio Grounding 9 ALARM _IN 1 WHITE/ORANGE Alarm Input 1 10 ALARM _IN 2 WHITE/BROWN Alarm Input 2 11 ALARM _IN 3 WHITE/RED Alarm Input 3 Group 12 ALARM _IN _GND PINK Alarm Input Grouding 13 ALARM _OUT 1A LIGHT GREEN Alarm Output 1, regardless of 14 ALARM _OUT 1B WHITE/BLACK positive or negative 15 DC 12V_OUT+ BLUE DC12V, output + Group 16 DC 12V_OUT- GREEN DC12V, output AN Series N o. T a g C o l o r G r o u p R e m a r k s 1 T V -O U T + B L A C K V id e o O u tp u t + 2 T V -O U T - B R O W N G ro u p V id e o O u tp u t - 3 R S _ A R E D R S S e ria l P o rt A 4 R S _ B O R A N G E R S S e ria l P o rt B 5 A U D IO _ IN P IN K A u d io In p u t 6 A U D IO _ O U T G R E Y G ro u p A u d io O u tp u t 7 A U D IO _ G N D P U R P L E A u d io G ro u n d in g 8 A U D IO _ G N D Y E L L O W A u d io G ro u n d in g 9 A L A R M _ IN 1 L IG H T G R E E N A la rm In p u t A L A R M _ IN _ G N D W H IT E G ro u p A la rm In p u t G ro u d in g 1 1 A L A R M _ O U T 1 A G R E E N A la rm O u tp u t 1, re g a rd le s s 1 2 A L A R M _ O U T 1 B B L U E o f p o s itiv e o r n e g a tiv e 6

16 Kedacom Two (2) Year Limited Hardware Warranty WHAT IS COVERED BY THIS WARRANTY? Kedacom warrants the Kedacom-branded hardware product and accessories contained in the original packaging (hereinafter referred to as "Kedacom Product") against defects in materials and workmanship when used normally in accordance with Kedacom's published guidelines for a period of TWO (2) YEARS from the date of original retail purchase in areas other than mainland China by the end-user purchaser (hereinafter referred to as "Warranty Period"). For the Kedacom Product purchased in mainland China, see the simplified Chinese version of this warranty for details. Kedacom's published guidelines include but are not limited to information contained in technical specifications, user guides, and service communications. The preceding applies unless otherwise agreed in the contract. WHAT IS NOT COVERED BY THIS WARRANTY? This warranty does not apply to any non-kedacom branded hardware products or any software, even if packaged or sold with Kedacom hardware. Manufacturers, suppliers, or publishers, other than Kedacom, may provide their own warranties to you but Kedacom, in so far as permitted by law, provides their products "AS IS". Software distributed by Kedacom with or without the Kedacom brand (including, but not limited to system software) is not covered by this warranty. Please refer to the licensing agreement accompanying the software for details of your rights with respect to its use. Kedacom does not warrant that the operation of the Kedacom Product will be uninterrupted or error-free. Kedacom is not responsible for damage arising from failures to follow instructions relating to the Kedacom Product's use. This warranty does not apply: (a) to consumable parts, such as batteries, unless failure has occurred due to a defect in materials or workmanship; (b) to cosmetic damage, including but not limited to scratches, dents, and broken plastic on ports; (c) to damage caused by use with another product; (d) to damage caused by acts outside the control of Kedacom, including without limitation acts of God, accidents, abuse, misuse, fire, storms, earthquakes, flood, or other external cause; (e) to damage caused by exposure of the product to heat, bright light, sun, liquids, sand, or other contaminants; (f) to damage caused by operating the Kedacom Product outside Kedacom's published guidelines; (g) to damage caused by service (including upgrades and expansions) performed by anyone other than a representative of Kedacom, Kedacom employee, or authorized Kedacom agent; (h) to an Kedacom Product that has been modified to alter functionality or capability without the written permission of Kedacom; (i) to defects caused by normal wear and tear or otherwise due to the normal aging of the Kedacom Product, or (j) if any serial number has been removed or defaced from the Kedacom Product. YOUR RESPONSIBILITIES If your Kedacom product is capable of storing data and other information, you should make periodic backup copies of the information contained on the storage media to protect the contents and as a precaution against possible operational failures. Before receiving warranty service, Kedacom or its authorized agents may require that you furnish proof of purchase details, respond to questions designed to assist with diagnosing potential issues, and follow Kedacom's procedures for obtaining warranty service. Before submitting your Kedacom Product for warranty service, you should maintain a separate backup copy of the contents of its storage media, remove all personal information that you want to protect, and disable all security passwords.

17 During warranty service, it is possible that the contents of the Kedacom product's storage media will be lost, replaced or reformatted. In such an event, Kedacom and its authorized agents are not responsible for any loss of data or other information contained on the storage media or any other part of the Kedacom product serviced. Following warranty service, your Kedacom Product or a replacement product will be returned to you as your Kedacom Product was configured when originally purchased, subject to applicable updates. You will be responsible for reinstalling all other data and information. Recovery and reinstallation of other data and information are not covered under this warranty. WHAT WILL KEDACOM DO IF THE WARRANTY IS BREACHED? If during the Warranty Period, you submit a valid claim to Kedacom or an authorized Kedacom agent, Kedacom will, at its option, (i) repair the Kedacom Product using new or previously used parts that are equivalent to new in performance and reliability, or (ii) exchange the Kedacom Product for a refund of your purchase price. A Kedacom replacement part or product, including a user-installable Kedacom part that has been installed in accordance with instructions provided by Kedacom, assumes the remaining warranty of the Kedacom Product or ninety (90) days from the date of replacement or repair, whichever provides longer coverage for you. When a product or part is replaced or a refund provided, any replacement item becomes your property and the replaced or refunded item becomes Kedacom's property. Kedacom reserves the right to refund the purchase price as its exclusive warranty remedy. HOW TO OBTAIN WARRANTY SERVICE? To seek warranty service, please contact a local authorized Kedacom agent. When contacting the agent via telephone, other charges may apply depending on your location. User Information Complete the form below and keep for ready reference. User Name: Address: Postal Code: Tel: Fax: Product Name: Mobile: Product Model: Date of Purchase:

20 V Overseas Hotline: 中国 : 江苏省苏州市高新区金山路 131 号 (215011) Tel: Fax: Suzhou Keda Technology Co.,Ltd. Singapore: 627A Aljunied Road, #09-07, BizTech Centre, Singapore Tel: Fax:

高清网络摄像机 HD IP Camera 快速安装指南 Quick Start Guide

高清网络摄像机 HD IP Camera 快速安装指南 Quick Start Guide 一前言感谢您购买我司产品, 如对本公司产品有疑问或需要, 请随时和我们联系我们尽最大努力来保证本手册信息的正确性, 如因升级等原因发生信息修改, 恕不另行通知获取最新文档请联系产品供应商二安全说明此内容 ( 手册 ) 的目的是确保用户正确使用本产品, 以避免危险或财产损失在使用产品之前,