- PDF Free Download

Size: px

Start display at page:

Download ""

称炬解
5 years ago
Views:

1 高清网络摄像机 HD IP Camera 快速安装指南 Quick Start Guide

3 一前言感谢您购买我司产品, 如对本公司产品有疑问或需要, 请随时和我们联系我们尽最大努力来保证本手册信息的正确性, 如因升级等原因发生信息修改, 恕不另行通知获取最新文档请联系产品供应商二安全说明此内容 ( 手册 ) 的目的是确保用户正确使用本产品, 以避免危险或财产损失在使用产品之前, 请认真阅读此手册并妥善保存以备日后参考如果用户因没有按照以下安全说明, 致使设备不能正常使用或损坏等情况, 责任由用户承担请使用满足安全电压要求的电源如果设备工作不正常, 请联系厂家或最近的服务中心不要以任何方式随意拆卸或修改设备请防止此产品从高处摔落或受强烈敲击清洁镜头时, 须使用吹气球或专业镜头布除去镜头上的污垢避免将摄像机对准强光 ( 如灯光照明太阳光等处 ) 聚焦, 否则容易引起过亮或漏光现象 ( 这并非摄像机故障 ) 也将影响摄像机寿命避免将产品暴露在非用户手册所示的工作环境下使用使用时不可让水或任何液体流入摄像机当运送摄像机时, 请重新以出厂时的包装进行包装, 或用同等品质的材质包装需要替换部件时, 请事先与经销商联系, 更换指定型号的部件, 或与原部件具有相同特性的部件擅自使用其它部件进行替换, 后果自负本产品非密封防水设备, 不能单独工作于室外露天环境工作环境工作电源 DC 12V±10% 温度 -30 ~60 湿度 10%~95%( 无凝结 ) 海拔高度 -60m~3000m 大气压 86kPa~106kPa 说明更多信息见附带光盘中的高清网络摄像机用户手册 1

4 三安装设备 1. 安装镜头取下防尘盖, 安装镜头, 如图 DC IRIS, 配备自动光圈镜头后可用图 1 安装镜头说明本系列摄像机不支持后焦调节 2. 支架安装说明将摄像机安装在吊装支架上时, 支架转接器可从设备底部拆卸下来并安装在设备上方, 如下图支架转接件摄像机俯视图螺孔图 2 安装支架转接器 2

5 3. 外罩安装说明当摄像机位于室外时, 需要装配在防水外罩中, 说明如下 : 1) 旋开卡扣如图, 打开护罩上盖 1 旋开卡扣图 3 打开护罩 2) 使用螺丝刀拧松固定板螺钉, 将固定板向后拉, 对准孔位取下固定板说明固定板螺钉拧松即可, 无需拧下 3) 穿好线缆并拧紧 PG 头 4) 将固定板装配在摄像机底部 4 对准孔位, 取下固定板 PG 头固定板螺孔 2 拧松螺丝摄像机 3 向后拉固定板 5) 将摄像机连同固定板安装在护罩中 5 穿线缆, 拧紧 PG 头图 4 将摄像机安装到护罩中 6 装配固定板注意固定前将摄像机镜头贴紧护罩前玻璃, 不要留明显间隙 ( 只需能调焦 ), 以免出现漏光光晕现象 6) 用线缆连接 IPC 的各接口和外罩中的接口板, 合上外罩上盖并锁紧注意暴露在立杆或防护罩外部的线缆一定要使用金属包塑波纹管进行保护 3

6 4. 线缆连接说明存储卡 ( 最大 128G) 插槽电源告警输入输出 RS232 串口 RS485 串口接地指示灯视频输出网络接口音频输出音频输入图 5 后面板说明说明 RUN 灯 : 运行指示灯, 绿色, 正常上电后快闪 (1 秒亮 1 秒灭 ), 断电后灯灭 LINK 灯 : 网络状态灯, 绿色, 正常上电切网络物理联通后快闪 (1 秒亮 1 秒灭 ), 断电或网络物理中断时灯灭四网络配置 1. 登录客户端最低配置和系统环境 : 处理器 :3.3GHz 酷睿 i3 系列及以上或相同性能的其他处理器 RAM 内存 :4GB 及以上操作系统 :WindowsXP 操作系统或更高版本浏览器 :IE7.0 及以上版本,Firefox,Google Chrome(41 及以下版本 ) DirectX:9.0c 说明本指南将以 WindowsXP 为例, 说明登录客户端步骤 4

1) 第一次使用时请运行光盘中附带的 IPCSearch, 在 IPCSearch 中将显示设备的 IP 地址网关等信息若 IPC

点击, 在弹出的界面中设置 admin 用户的密码和找回密码时需要用的邮箱, 点击激活按钮激活设备待设备重启 3 2 图 6 在

填写以太网参数修改参数配置, 需要填写管理员用户用户名 (admin) 及激活设备时所设置的密码完成 IP 配置后,

7 1) 第一次使用时请运行光盘中附带的 IPCSearch, 在 IPCSearch 中将显示设备的 IP 地址网关等信息若 IPC 设备所接入的网络有 DHCP 服务,DHCP 服务器将自动给 IPC 分配 IP 地址 2 ) 在 IPCSearch 中选中设备, 点击, 在弹出的界面中设置 admin 用户的密码和找回密码时需要用的邮箱, 点击激活按钮激活设备待设备重启 3 2 图 6 在 IPCSearch 上激活设备并修改网络参数 3 ) 点击, 在弹出的界面中配置网络参数静态分配 IP 地址时, 请选择自定义地址, 填写以太网参数修改参数配置, 需要填写管理员用户用户名 (admin) 及激活设备时所设置的密码完成 IP 配置后, 设备将自动重启, 重启时间约为 60 秒 4 ) 在 IPCSearch 中双击设备或点击, 输入用户名和密码 ( 如图 7 ), 登录 Web 客户端 5

8 图 7 登录设备 5) 登录成功后, 下载并安装视频插件图 8 激活设备说明如果直接通过 Web 端首次登录未激活的设备, 可在登录界面设置管理员的密码激活设备 ( 如图 8 ) 登录前需要先将 PC 机设置为与设备在同一网段 2. 图像调节和镜头调整进入客户端后可以直接浏览图像, 界面如图说明不同型号浏览界面略有差异, 请以设备实际界面为准更多客户端说明参见客户端帮助文档调整设备方向, 在 Web 客户端上进行参数调整, 直到浏览画面达到预定要求图 9 浏览界面 6

9 本保修卡适用于您购买的本公司系列产品 1. 终身保质, 免费保修期一年 ( 仅限中国大陆地区, 中国大陆以外地区请参考英文说明 ) 2. 凡保修期内, 由于本产品自身引起的故障, 请与公司售后服务部联系 3. 保修时我们将使用您的保修卡信息, 请认真填写 4. 以下情况, 属于有偿保修范围 : - 人为原因造成的设备故障 - 因使用环境不符合本产品要求造成的故障 - 因不可抗力造成的产品损坏 - 无保修卡 - 已过保修期用户名称 : 详细地址 : 传真 : 电话 : 邮箱 : 邮编 : 产品名称 : 产品型号 : 购买日期 :

10 Preface Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact us. Every effort has been made to ensure the accuracy and validity of this Guide. Any update of this Guide is subject to change without notice. For the latest document, please contact the dealer. Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Please read this Guide carefully before using the product, and keep it properly for future reference. If the product cannot work normally or is damaged because the user does not follow the safety instructions, we shall not assume any responsibility. Please adopt power supply in the safety voltage range. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble or repair the product yourself in any way. Do not drop the camera or subject it to physical shock. When cleaning the lens, please use a rubber dust blower or lens cleaning cloth to remove the dirt. Do not focus the camera lens on strong light such as the sun or incandescent lamp. The strong light can cause overexposure or light leak (not camera malfunction), which may shorten camera lifetime. Do not expose the camera in the environment not defined in the Guide. Operating Environment Working Voltage DC12V±10% Temperature -30 ~60 Humidity Altitude Atmospheric Pressure 10%~95% (non-condensing) -60m~3000m 86kPa~106kPa Keep the camera away from water or any liquid. While shipping the camera, pack it in the factory packing or use materials with equivalent quality. When it is necessary to replace a part, please contact your dealer in advance and replace the part with specified model or part of the same features. We shall not assume any responsibility for problems caused by unauthorized replacement. The camera is not water-proof and cannot work in outdoor environment alone. [Note] For more information, please refer to the User Manual for HD IP Camera in the attached CD. 1

11 Installation Steps 1. Mount Camera Lens 1. Remove the dust cover and mount the lens. DC IRIS, useful after mounting auto IRIS lens Picture 1 [Note]: Back focus adjustment is unavailable for this series. 2. Mount Bracket When mount the camera on a ceiling mount bracket, the bracket adapter can be taken apart from the bottom and be mounted on the top of the camera, as the picture shows. Bracket Adapter Camera Top View Screw Hole Picture 2 3. Install Housing When the camera works outdoor, it should be installed in a water-proof housing, steps: 1) Unscrew the snap-fit and open the cover of the housing, as the picture shows. 1 Open the snap-fit Picture 3 2

12 2) Use a screwdriver to loosen the screws on the holder, pull the holder backward and take it from the holes. [Note]: Only unscrew the screws on the holder, no need to screw them off. 3) Route the cable and screw up the PG joint. 4) Fix the holder at the bottom of the camera. 4 Align to the hole, take off the fixing board PG Joint Holder Camera Screw Hole 2 Loosen screws 3 Pull the holder backward 5 Route cables & tighten PG joint Picture 4 6 Assemble fixing board 5) Install the camera and holder in the housing. [Warning]: Before fixing, put the camera lens close to the window of the housing without any obvious gap (gap only enough for focus), to avoid light leak or halo. 6) Wire camera connectors to the connector board of the housing, cover the housing and lock it up. [Warning]: Cables exposed on the pole or outside the housing must be protected by plastic-coated metal corrugated pipe. 4. Wiring and Power On TF Card Slot Max Memory 128G Power Supply Alarm In/Out RS-232 Port RS-485 Port Grounding Indicator Lamp Video Output Ethernet Port Audio Input Audio Output Picture 5 Back Panel 3

[Note]: RUN Lamp: operating indicator, green, flashes (1s on, 1s off) after power on, be off after power off.

Login client System for client installation: Processor: 3.3 GHz CORE i3 series or other equivalent processors RAM Memory: 4GB or above Operating System: Windows XP or newer version Browser: IE7.

1) When use the device for the first time, run the IPCSearch in the attached CD and set camera IP address and gateway.

13 [Note]: RUN Lamp: operating indicator, green, flashes (1s on, 1s off) after power on, be off after power off. LINK Lamp: network status indicator, green, flashes (1s on, 1s off) after power on and networked, be off when power off or network disconnected. Network Setting 1. Login client System for client installation: Processor: 3.3 GHz CORE i3 series or other equivalent processors RAM Memory: 4GB or above Operating System: Windows XP or newer version Browser: IE7.0 or newer, Firefox, Google Chrome (below 41) DirectX:9.0c [Note]: This Guide will take Windows XP as example to explain client login steps. 1) When use the device for the first time, run the IPCSearch in the attached CD and set camera IP address and gateway. If the network provides DHCP service, DHCP server will assign IP for the camera automatically. 2) Select the device and click Batch processing. In the popup interface, set admin user s password and the e- mail address to find back the password. Click Active and wait for rebooting. Picture 6 3) Click Modify Params and set the network parameters. When configure a static IP for the camera, please check Custom device address (Close DHCP) and fill the Ethernet parameter. During the modification, the user name (admin) and the password set before activation should be entered. After configuration, the camera will reboot automatically and this takes 60s. 4

[Note]: If login the nonactivated camera by web client, you can set admin user s password on the login interface to activate the device (as in Picture 8).

14 4) Double click the device in IPCSearch or click Login, and enter user name and password (as in Picture 7) to login the device. Picture 7 Picture 8 5) After login, download and install the plug-in. [Note]: If login the nonactivated camera by web client, you can set admin user s password on the login interface to activate the device (as in Picture 8). Before setting, set the PC and the device in the same LAN. 2. Live View and Lens Adjustment After login, user can view live video directly, as the picture shows. [Note]: The live view interface of different models may differ. Please refer to the help file. Adjust camera direction, adjust camera parameters by the web client until the live view meets requirement. Picture 9 5

15 Kedacom Two (2) Year Limited Hardware Warranty WHAT IS COVERED BY THIS WARRANTY? Kedacom warrants the Kedacom-branded hardware product and accessories contained in the original packaging (hereinafter referred to as "Kedacom Product") against defects in materials and workmanship when used normally in accordance with Kedacom's published guidelines for a period of TWO (2) YEARS from the date of original retail purchase in areas other than mainland China by the end-user purchaser (hereinafter referred to as "Warranty Period"). For the Kedacom Product purchased in mainland China, see the simplified Chinese version of this warranty for details. Kedacom's published guidelines include but are not limited to information contained in technical specifications, user guides, and service communications. The preceding applies unless otherwise agreed in the contract. WHAT IS NOT COVERED BY THIS WARRANTY? This warranty does not apply to any non-kedacom branded hardware products or any software, even if packaged or sold with Kedacom hardware. Manufacturers, suppliers, or publishers, other than Kedacom, may provide their own warranties to you but Kedacom, in so far as permitted by law, provides their products "AS IS". Software distributed by Kedacom with or without the Kedacom brand (including, but not limited to system software) is not covered by this warranty. Please refer to the licensing agreement accompanying the software for details of your rights with respect to its use. Kedacom does not warrant that the operation of the Kedacom Product will be uninterrupted or error-free. Kedacom is not responsible for damage arising from failures to follow instructions relating to the Kedacom Product's use. This warranty does not apply: (a) to consumable parts, such as batteries, unless failure has occurred due to a defect in materials or workmanship; (b) to cosmetic damage, including but not limited to scratches, dents, and broken plastic on ports; (c) to damage caused by use with another product; (d) to damage caused by acts outside the control of Kedacom, including without limitation acts of God, accidents, abuse, misuse, fire, storms, earthquakes, flood, or other external cause; (e) to damage caused by exposure of the product to heat, bright light, sun, liquids, sand, or other contaminants; (f) to damage caused by operating the Kedacom Product outside Kedacom's published guidelines; (g) to damage caused by service (including upgrades and expansions) performed by anyone other than a representative of Kedacom, Kedacom employee, or authorized Kedacom agent; (h) to an Kedacom Product that has been modified to alter functionality or capability without the written permission of Kedacom; (i) to defects caused by normal wear and tear or otherwise due to the normal aging of the Kedacom Product, or (j) if any serial number has been removed or defaced from the Kedacom Product. YOUR RESPONSIBILITIES If your Kedacom product is capable of storing data and other information, you should make periodic backup copies of the information contained on the storage media to protect the contents and as a precaution against possible operational failures. Before receiving warranty service, Kedacom or its authorized agents may require that you furnish proof of purchase details, respond to questions designed to assist with diagnosing potential issues, and follow Kedacom's procedures for obtaining warranty service. Before submitting your Kedacom Product for warranty service, you should maintain a separate backup copy of the contents of its storage media, remove all personal information that you want to protect, and disable all security passwords.

16 During warranty service, it is possible that the contents of the Kedacom product's storage media will be lost, replaced or reformatted. In such an event, Kedacom and its authorized agents are not responsible for any loss of data or other information contained on the storage media or any other part of the Kedacom product serviced. Following warranty service, your Kedacom Product or a replacement product will be returned to you as your Kedacom Product was configured when originally purchased, subject to applicable updates. You will be responsible for reinstalling all other data and information. Recovery and reinstallation of other data and information are not covered under this warranty. WHAT WILL KEDACOM DO IF THE WARRANTY IS BREACHED? If during the Warranty Period, you submit a valid claim to Kedacom or an authorized Kedacom agent, Kedacom will, at its option, (i) repair the Kedacom Product using new or previously used parts that are equivalent to new in performance and reliability, or (ii) exchange the Kedacom Product for a refund of your purchase price. A Kedacom replacement part or product, including a user-installable Kedacom part that has been installed in accordance with instructions provided by Kedacom, assumes the remaining warranty of the Kedacom Product or ninety (90) days from the date of replacement or repair, whichever provides longer coverage for you. When a product or part is replaced or a refund provided, any replacement item becomes your property and the replaced or refunded item becomes Kedacom's property. Kedacom reserves the right to refund the purchase price as its exclusive warranty remedy. HOW TO OBTAIN WARRANTY SERVICE? To seek warranty service, please contact a local authorized Kedacom agent. When contacting the agent via telephone, other charges may apply depending on your location. User Information Complete the form below and keep for ready reference. User Name: Address: Postal Code: Tel: Fax: Product Name: Mobile: Product Model: Date of Purchase:

20 V Overseas Hotline: 中国 : 江苏省苏州市高新区金山路 131 号 (215011) Tel: Fax: Suzhou Keda Technology Co.,Ltd. Singapore: 627A Aljunied Road, #09-07, BizTech Centre, Singapore Tel: Fax:

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact