Microsoft Word MRS Program Update Instruction Windows.v1.6.doc

Transcription

1 MRS Program Update Instruction MRS 主程式升級使用說明 注意事項 : 在程式更新後, 所有參數設定將回復到出廠預設值 在程式更新前, 請確保您已儲存您的參數資料, 或已將參數資料拍照儲存 ** Please be noted that all the setting will be reset to default value after updating. So make sure to save or picture your parameter setting firstly before firmware update. 更新前請先重新整理頁面, 確認主程式為最新版本 Refresh MRS download page to make sure the firmware is latest version before update. 解壓縮前請先關閉防毒軟體 Before file decompressing, make sure to turn off the antivirus software first. 1. 儲存 MRS 參數設定檔案 (MRS App) Save MRS Parameters Setting (MRS App) 更新 MRS 主程式前請務必先將您機體上參數設定儲存至手機 ( 建議在連線的狀況下儲存參數設定 ), 如沒儲存參數設定直接進行更新, 會導致您機體上的參數設定遺失, 造成不便 Before MRS firmware updating, make sure to save all your parameter settings in your mobile phone when connected. After MRS firmware updating, all the parameter settings will reset to default settings, so make sure to double check and confirm the saving firstly.

2 2. 將 AlignMRSUpdate 進行解壓縮後, 壓縮檔裡有兩個檔案, 分別是主程式 AlignMRSUpdate.exe 更新檔 MRS_firmware_V1.6.mrs After decompressing AlignMRSUpdate file, there are three files included. 3. 執行 AlignMRSUpdate.exe 安裝程式 Click AlignMRSUpdate.exe to install the system. 4. 執行畫面出現時點選 Next Then click Next.

3 5. Welcome 畫面出現時點選 Next Click Next. 6. 選擇安裝路徑 ( 建議使用預設 ) 點選 Next Then choose installation folder, then click Next.

4 7. Select Components 畫面出現時點選 Next Then click Next in Select Components Window. 8. License Agreement 畫面出現時選取 I accept the license 點選 Next Then choose I accept the license and click Next.

5 9. MRS Installer Setup 畫面出現時點選 Next For MRS Installer Setup, click Next. 10. 開始安裝 Then start install.

6 11. 安裝完成 Complete installation. 12. 打開您的 MR25 電源 ( 更新 MRS 時務必將螺旋槳拆下避免發生危險 ) Then power on your MR25. (When updating MRS firmware, please make sure to remove propellers firstly to prevent any unexpected danger.) 13. 電腦 -> 右鍵 -> 管理 -> 裝置管理員 -> 連接埠, 進入 Windows 裝置管理員確認連接埠為哪個, 通常數字較為前面的是藍芽裝置 以下範例未連結 MRS 時圖示 Searching for Bluetooth Device: My Computer > Right Click > Management > COM & LPT. 14. 桌面右下角選擇藍芽圖示的裝置, 右鍵預覽藍芽位置, 搜尋藍芽連接 ALIGN MRS At the right bottom of your desktop, please click Bluetooth device icon, right click to search for ALIGN MRS.

7 15. 完成 ALIGN MRS 連結後, 連接埠會新增一個新的裝置 (COM30) 依裝置不同, Bluetooth Serial Port 也會不同. After ALIGN MRS connection, there will be new device coming out, for example: here we get new COM 進入主程式 MRSUpdate, 選取 Port 如果選錯會連線錯誤, 可以嘗試重新打開程式並選擇另一個連接埠 Click and get into MRS Firmware, select port COM3. Wrong port selection will lead to disconnection, if so, please re-open the MRS Firmware and select the correct Port. 17. 點擊 Update 後出現選取視窗, 選擇官網下載.mrs 韌體更新檔案 Click Update, please click Firmware.mrs to start the update process in Find Files. PS. After confirmation, the update process will start within 4~5 seconds. sure not to power off your computer & aircraft or disconnect Bluetooth connection to prevent any mistake installation. Make

8 18. MRS 韌體更新完成, 更新完成後您的 MR25 會自行關機 ( 此為正常現象 ) After completing MRS firmware update, your MR25 will automatically power-off. This is normal condition. 備註 : 如更新失敗會出現以下圖示, 請重新選擇正確的 Port PS. If the update process failed, then you ll get error message for Please try again or change port. In this case, please choose the correct Port again. 19. 陀螺儀校正 (MRS App) Gyro Calibration(MRS App) MRS 韌體更新完成後, 務必先將陀螺儀重新校正, 避免飛行時發生危險 After MRS firmware updated, must re-do the gyro calibration to prevent any unforeseen damage.

9 20. 讀取 MRS 參數設定檔案 (MRS App) Read MRS Parameter Setting (MRS App) 完成 MRS 主程式更新後, 開啟您 MR25 與 MRS App 進行連線, 可把之前儲存好的參數設定讀取出來使用或與人分享 After MRS firmware updating, you can power on MR25 and connect with MRS App, then you can read your parameter saved files and share with other pilots.

10 MRS 重新連線時, 相機所有參數設定將會恢復原廠預設值, 如需調整請重新設定 When connect to MRS system, all DV camera settings will reset to default value every time, so make sure to check and set your preferred settings before each flight. 更新完後, 請再次檢查主程式及 APP 介面都是最新版本 After update, please check again to make sure both firmware and software are latest version.