SPECIFICATION FOR APPROVAL CUSTOMER : CUSTOMER P.N. : PRODUCT MODEL : JAMSP-ZA700IC72VO-050D PRODUCT NO. : MFT0057-NO SAMPLE DATE : 2013-06-01 CUSTOMER AUTHORIZED SIGNATURE Please return to us one copy of SPECIFICATION FOR APPROVAL with you approved signature. Jaro Components, Inc. 6600 Park of Commerce Blvd. Boca Raton, FL 33487 TEL: (561)241-6700 FAX: (561)241-3328 http://www.jarocomponents.com Prepared By: Checked By: Approved By: Page 1
Revision History Description of Change Rev. Changed Date Notes Before After A/0 Original Release --- 2013-06-01 --- Page 2
Table Of Content 1. Scope... 4 2. Input Characteristics... 4 2.1. Input Voltage & Frequency... 4 2.2. Input AC Current... 4 2.3. Inrush Current (cold start)... 4 2.4. Power Factor... 4 2.5. Efficiency... 4 3. Output Characteristics... 4 3.1. Static Output Characteristics <Vo & R&N<5000mVp-p >... 4 3.2. Voltage/Current Curve... 5 3.3. Turn - on Delay Time... 5 4. Protection Requirements... 5 4.1. Short Circuit Protection... 5 4.2. Over Voltage Protection... 5 5. Environment Requirements... 5 5.1. Operating Temperature and Relative Humidity... 5 5.2. Storage Temperature and Relative Humidity... 5 5.3. Vibration... 5 6. Reliability Requirements... 5 6.1. Life Time Qualification... 5 6.2. MTBF Qualification... 5 7. Safety & EMI/EMS Standards... 6 7.1. Safety Category... 6 7.2. EMI Standards... 6 7.3. Energy Star Standards... 6 7.4. EMS Standards... 6 8. Main Safety Test Items... 7 8.1. Dielectric Strength(Hi-pot)... 7 8.2. Leakage Current... 7 8.3. Insulation Resistance... 7 9. Derating Curve... 7 10. Dimming Explain... 8 10.1. Dimming sketch map shown as following... 8 10.2. Dimming Voltage/Current Proportion Curve:... 8 11. Mach. Outline Drawing... 9 12. I/O Marking Drawing... 10 Page 3
1. Scope The document detail the electrical, mechanical and environmental specifications of a 50W constant current LED driver. The LED driver shall meet the RoHS requirement. Description: LED driver (With AL Case) Open Frame 2. Input Characteristics 2.1. Input Voltage & Frequency LED driver (With Plastic Case) Others The range of input voltage is from 90 to 305Vac single phase. Items Minimum Nominal Maximum Input Voltage 90Vac 100-277Vac 305Vac Input Frequency 47Hz 60Hz/50Hz 63Hz 2.2. Input AC Current 0.8Amax. @ 100-277Vac input & full load. 2.3. Inrush Current (cold start) 65Amax. @ 230Vac input 25. 2.4. Power Factor Typical value is 0.95@110Vac input &100% load; Typical value is 0.90@220Vac input &100% load. 2.5. Efficiency Typical value is 83% @110Vac input & full load; Typical value is 85% @220Vac input & full load. 3. Output Characteristics 3.1. Static Output Characteristics <Vo & R&N<5000mVp-p > Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 10uF electrolysis capacitor. (test under the condition of rated input and rated output) Page 4
3.2. Voltage/Current Curve Vcharge 77V 72V 43V 0V 0.644A 0.7A 0.756A Icharge Constant Current Output Characteristics Min. Typ. Max. 3.3. Turn - on Delay Time 3.0S max. @ 100-277Vac input & full load. 4. Protection Requirements 4.1. Short Circuit Protection The input power shall decrease when the output rail short, the power supply shall no damage, and shall be self-recovery when the fault condition is removed. 4.2. Over Voltage Protection When the output voltage is over (1.2-1.4)Vout,the product will shutdown and enter protection status, the driver will re-start and work normally if the fault condition was eliminated. 5. Environment Requirements 5.1. Operating Temperature and Relative Humidity -25 to +50 ; 5%RH to 95%RH. 5.2. Storage Temperature and Relative Humidity -35 to +70 ; 5% to 95%RH non-condensing at Sea level shall be low 10,000 feet. 5.3. Vibration 10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth: 3.5mm) for 1Hour for each of the perpendicular axes X, Y, Z. 6. Reliability Requirements Output Current Range 0.644A 0.7A 0.756A Output Voltage Range 43V / 72V 6.1. Life Time Qualification The life time shall be at least 3 years at 110Vac input,80% load and 45 ambient temperature. 6.2. MTBF Qualification The MTBF shall be at least 490,000 hours at 110Vac, 80% load and 25 ambient temperature(mil-hdbk-217f). Page 5
7. Safety & EMI/EMS Standards 7.1. Safety Category Safety Category Country Standard CUL USA & Canada UL8750,UL935,UL1012,UL1310 Class 2,CSA-C22.2 No.107.1,CSA C22.2 No.223-M91 Class 2 CE Europe EN 61347-1,EN 61347-2-13 7.2. EMI Standards EMI Standards Country Notes EN 55015 Europe Conducted emission Test & Radiated emission Test with 6 db margin FCC USA FCC Part 15 class B,ANSI C63.4:2009 7.3. Energy Star Standards Energy Star Standards ANSI / IEEE C62.41-1991 Notes Transient protection,power supply shall comply with Class A operation.the line transient shall consist of seven strikes of a 100kHz ring wave,2.5kv level,for both common mode and differential mode 7.4. EMS Standards EN 61000-3-2 Harmonic current emissions EN 61000-3-3 Voltage fluctuations & flicker EN 61000-4-2 Electrostatic Discharge(ESD): 8kV air discharge, 4kV contact discharge EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS EN 61000-4-4 Electrical Fast Transient / Burst-EFT EN 61000-4-5 Surge Immunity Test: AC Power Line: line to line 1 kv EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS EN 61000-4-8 Power Frequency Magnetic Field Test EN 61000-4-11 Voltage Dips EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment Page 6
8. Main Safety Test Items 8.1. Dielectric Strength(Hi-pot) Primary to Secondary: 3750Vac 10mAMax / 60second(3second for production)/finished goods 8.2. Leakage Current 0.5mAmax. at 240Vac/50Hz input. 8.3. Insulation Resistance The IR shall be at least 50MΩ when apply 500Vdc between primary and secondary. 9. Derating Curve Derating Curve Derating Curve 100 100 80 80 Load(%) 60 40 20 Load(%) 60 40 20 0-35 -20-5 10 25 40 55 70 Ambient Temperature( æ) 0 90 120 150 180 210 240 270 300 Input Voltage(V) 330 Page 7
10. Dimming Explain 10.1.Dimming sketch map shown as following AC/L Brown Vout(-) Vout(+) Black Red LED Lamp AC/N Blue LED Driver 0V-10V Red 0-10V Dimmer GND Black Notes: 1 A 0-10V dimmer connected to DIM Port for achieving 20-100% brightness dimming by changing the voltage(0-10v) of Isense. 2 One LED driver, one brightness controller control one LED lamp only. 10.2.Dimming Voltage/Current Proportion Curve: Dimming Voltage(V) 0 1 2 3 4 5 6 7 8 9 10 Dimming Current(A) 0.141 0.182 0.228 0.273 0.328 0.387 0.449 0.509 0.568 0.629 0.688 Dimming Current(A) 0.64 0.59 0.54 0.49 0.44 0.39 0.34 0.29 0.24 0.19 0.14 0 1 2 3 4 5 6 7 8 9 10 Voltage(V) Page 8
11. Mach. Outline Drawing 1. Tolerance:unmarked tolerance all is ±0.5,marked according to tolerance of it 2. Unit/ 单位 :mm 10.10 165.5±0.5 42.00 260±10 30±5 310 +20-0.0 黑色 /Black 45.00 红色 /Red 红色 /Red 5.00 2.00 26.00 R2.00 2.00 黑色 /Black 265+10 30.8±0.5 4.00 154.0±0.5 33.50 Dimensions Millimeters(Inches) Wire Specification Length 165.5(6.52) AC Input 2*1.0mm 2 CCC+VDE Width 42(1.65) DC Output UL1015 18AWG Height 33.5(1.32) Dimming UL2464 20AWG Page 9
12. I/O Marking Drawing Page 10