穨C-7IXE PDF

Transcription

1 WARNING: Never run the processor without the heatsink properly and firmly attached PERMANENT DAMAGE WILL RESULT! Mise en garde : Ne faites jamais tourner le processeur sans que le dissipateur de chaleur soit fixé correctement et fermement UN DOMMAGE PERMANENT EN RÉSULTERA! Achtung: Der Prozessor darf nur in Betrieb genommen werden, wenn der Wärmeableiter ordnungsgemäß und fest angebracht ist DIES HAT EINEN PERMANENTEN SCHADEN ZUR FOLGE! Advertencia: Nunca haga funcionar el procesador sin el disipador de calor instalado correcta y firmemente SE PRODUCIRÁ UN DAÑO PERMANENTE! Aviso: Nunca execute o processador sem o dissipador de calor estar adequado e firmemente conectado O RESULTADO SERÁ UM DANO PERMANENTE!

2

3 DECLARATION OF CONFORMITY Per FCC Part 2 Section (a) Responsible Party Name: GBT INC hereby declare s that the product Address: Valley Blvd, Suite#A LA Puent, CA Phone/Fax No: (818) / (818) Product Name: Mother Board Model Number: Conforms to the following specifications: FCC Part 15, Subpart B, Section 15107(a) and Section 15109(a), Class B Digital Device Supplementary Information: GA- 7IXE4 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation Representative Person's Name: Signature: ERIC LU Eric Lu Date: Jul 4, 2000 FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Move the equipment away from the receiver -Plug the equipment into an outlet on a circuit different from that to which the receiver is connected -Consult the dealer or an experienced radio/television technician for additional suggestions You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void Your authority to operate such equipment This device complies with Part 15 of the FCC Rules Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation

4 Declaration of Conformity We, Manufacturer/Importer (full address) GBT Technology Träding GMbH Ausschlager Weg 41, 1F, Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-7IXE4 is in conformity with (reference to the specification under which conformity is declared) in accordance with 89/336 EEC-EMC Directive EN Limits and methods of measurement EN * Disturbances in supply systems caused of radio disturbance characteristics of EN by household appliances and similar industrial, scientific and medical (ISM electrical equipment Harmonics high frequency equipment EN55013 Limits and methods of measurement EN * Disturbances in supply systems caused of radio disturbance characteristics of EN by household appliances and similar broadcast receivers and associated electrical equipment Voltage fluctuations equipment EN Limits and methods of measurement EN Generic emission standard Part 1: of radio disturbance characteristics of Residual, commercial and light industry household electrical appliances, portable tools and similar electrical EN Generic immunity standard Part 1: apparatus Residual, commercial and light industry EN Limits and methods of measurement EN Generic emission standard Part 2: of radio disturbance characteristics of Industrial environment fluorescent lamps and luminaries EN Immunity from radio interference of EN Generic immunity standard Part 2: broadcast receivers and associated Industrial environment equipment EN Limits and methods of measurement ENV Immunity requirements for household of radio disturbance characteristics of appliances tools and similar apparatus information technology equipment DIN VDE 0855 Cabled distribution systems; Equipment EN EMC requirements for uninterruptible part 10 for receiving and/or distribution from power systems (UPS) part 12 sound and television signals CE marking (EC conformity marking) The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 73/23 EEC EN Safety requirements for mains operated EN Safety for information technology equipment electronic and related apparatus for including electrical business equipment household and similar general use EN Safety of household and similar EN General and Safety requirements for electrical appliances uninterruptible power systems (UPS) Manufacturer/Importer Signature : Rex Lin (Stamp) Date : Jul 4, 2000 Name : Rex Lin

5 7IXE4 AMD TM Athlon AGP AMD TM Athlon R C

6 REV 10 Second Edition : 1) 2) 3) 4) 5) 6) BIOS BIOS 7)

7 P1 P2 P3 7IXE4 P5 CPU / P6 P19 P20 P21 BIOS P22 P52

8

9 7IXE4 10 7IXE4 Jun IXE4 Jul

10 7IXE4 (TUCD) COM B USB SCSI 7IXE4 2

11 7IXE4 CPU ATX ( 304 x 22 ) AMD Athlon(K7) Socket A CPU 64K/256K 2nd 500MHz ~ 1GHz CPU AMD 750, : AMD 751 PCI/AGP (PAC) AMD 756 PCI ISA IDE 90 / 95 / 100 / 105 / 110 / 115MHz ICS pin DIMM SDRAM 16MB~768MB( ) 33V SDRAM DIMM I/O Winbond AGP (Accelerated Graphics Port) - 66 / 133 MHz 33V AGP-Bus 5 32-bit PCI Bus 2 16-bit ISA Bus IDE IDE AMD 756 PCI PIO, Bus Master, Ultra DMA/33 ATA 66 IDE HDD/CD-ROM IDE 1 (360K,720K,12M,144M 288M bytes) 1 Normal/EPP/ECP 2 (COM A & COM B) 4 USB 1 ( Fast IrDA ) ( ) CPU/ / CPU/ / CPU 3

12 PS/2 BIOS PS/2 PS/2 AMI BIOS, 2M bit AC back 4

13 7IXE4 7IXE4 PS/2 USB COM A LPT JP10 J30 Socket A CPU COM B JP2 ATX POWER FLOPPY J9 AMD751 IDE1 IDE2 JP15 AGP DIMM3 DIMM2 DIMM1 Battery PCI1 JP1 7IXE4 JP13 PCI2 SW1 J3 PCI3 BZ1 USB PCI4 AMD756 JP5 JP4 JP9 J22 PCI5 ISA1 BIOS J6 ISA2 JP12 5

14 7IXE4 CPU / P8 COM A / COM B / LPT P8 USB P8 PS/2 PS/2 P9 JP2 P9 J9 CPU / J6 P10 ATX P11 FLOPPY( ) P11 IDE 1 / IDE 2 P12 USB P12 IR( ) ) P13 JP9 ( ) P13 JP4 ( ) P14 J30 (HDT Herder ) P14 P15 J22 (2x11 pins ) P15 JP10 (PS/2 ) P16 JP1 ( ) P16 JP12 (BIOS ) P17 JP5 ( ) ) P17 JP3 ( CMOS ) P18 JP15 (SIP ) ( ) P18 6

15 7IXE4 CPU SW1 90MHz, 95MHz, 100MHz, 105MHz, 110MHz and 115MHz Jumper CPU SW1: CPU Speed Setup 90MHz ON SW1 105MHz ON SW1 95MHz ON SW1 110MHz ON SW1 100MHz ON SW1 115MHz ON SW1 1 CPU,, AMD CPU :, 7

16 COM A / COM B / LPT LPT PORT COM A COM B USB USB V0 2 USB D0-3 USB D USB V USB D1-7 USB D1+ 8 8

17 7IXE4 9

18 PS/2 PS/2 PS/2 PS/ VCC(+5V) PS/2 6 4 JP V 3 10

19 7IXE4 J9 CPU V 3 J V 3 11

20 12

21 7IXE4 ATX ,5,7,13, ,2,11 33V 4,6,19,20 VCC V 12-12V 18-5V 8 9 5V SB stand by+5v 14 PS-ON(Soft On/Off) FLOPPY : 13

22 IDE1 IDE2 IDE 1 IDE 2 USB VCC 2 USB D0 3 USB D VCC 6 USB D1 7 USB D

23 7IXE4 IR : ( ) 1 1 IR 2 3 IR 4 5 (+) JP9 : ( Ring Power On)

24 JP4 : V SB 2 3 J30: HDT Herder (For testing purpose only)

25 7IXE4 J22 : For 2X11 Pins GN 1 HD 1 GD PW P+P P 1 1 S P K RE GN : : (Green Switch) : GD : 1: LED (+) (Green LED) 2: LED ( ) HD : 1: LED (+) (IDE Hard Disk Active LED) 2: LED ( ) SPK : (Speaker Connector) 1: VCC(+) 2-3: 4: ( ) RE : : (Reset Switch) : P+P P : 1: LED (+) (Power LED) 2: LED ( ) 2: LED ( ) PW : (Soft Power Connector) : : 15

26 16

27 7IXE4 JP10 : PS/ PS/2 2-3 PS/2 JP1 :

28 JP12: BIOS 1 ( ) BIOS, Jumper JP12, BIOS JP5: 1 ( ) 18

29 7IXE4 JP3 : CMOS CMOS ( 1-2 ) 2-3 JP15: SIP Select ( ) close Ext SIP( ) 2-3 close Int SIP 19

30

31 7IXE4 7IXE4 CPU AMD Athlon TM 950MHz (128x2)MB SDRAM (KINGMAX KSV884T4A1A-07) CPU 256 KB GA-GF2560 (32MB) IDE ( Quantum KA13600AT) Windows NT 40 SPK x 768 x 64k colors x 75Hz Bus Master AMD-756 Bus Master IDE Controller V122RC Processor AMD Athlon 950MHz(100x95) Winbench99 CPU mark FPU Winmark Business Disk Winmark Hi-End Disk Winmark Business Graphics Winmark Hi-End Graphics Winmark Winstone99 Business Winstone Hi-End Winstone

32 Socket A 100MHz 14318MHz AGP System Bus 100MHz 66MHz AMD MHz 66MHz 33V SDRAM 100MHz 5 PCI 33MHz ICS / MHz ATA66 IDE Channels 14318MHz 33MHz 4 USB Ports AMD 756 BIOS 8MHz COM Ports ISA Bus LPT Ports Winbond W83977 Game Port PS/2 IR Floppy 20

33 7IXE4 7IXE4 3 (DIMM) BIOS DIMM, DIMM DIMM 1 DIMM 2 DIMM pin SDRAM DIMM Modules 16 / 32 / 64 / 128 / 256 MB X 1 pcs 16 / 32 / 64 / 128 / 256 MB X 1 pcs 16 / 32 / 64 / 128 / 256 MB X 1 pcs 21

34 BIOS BIOS P24 CMOS P26 BIOS P29 P32 P36 PCI P39 BIOS P41 SETUP P42 P43 P46 (Supervisor)/ (User) P48 IDE P49 SETUP P50 SETUP P51 22

35 7IXE4 BIOS AMI BIOS CMOS SETUP CMOS SETUP CMOS RAM CMOS RAM ENTERING SETUP BIOS POST Power On Self Test Del AMI BIOS CMOS SETUP POST Del CMOS SETUP <Ctrl Alt Del Reset POST Del CMOS SETUP Esc Page Up Page Down SETUP F1 F2 F3 F4 F5 ( ) F6 BIOS ( ) F7 SETUP ( ) F8 F9 F10 CMOS SETUP SETUP SETUP 23

36 BIOS F1 BIOS CMOS SETUP <Esc> CMOS SETUP,, Enter AMIBIOS SIMPLE SETUP UTILITY VERSION 122 (C) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP / PCI CONFIGURATION LOAD BIOS DEFAULTS INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC: Quit : Select Item (Shift)F2 : Change Color F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults F10:Save & Exit Time, Date, Hard Disk Type 1: Standard CMOS Features ( CMOS ) BIOS features setup(bios ) BIOS 24

37 7IXE4 Chipset features setup ( ) DRAM Timing ISA Clock Power management setup( ) CPU GREEN PNP/PCI configuration( PCI ) ISA PnP PCI Load BIOS defaults ( BIOS ) BIOS CMOS Load Setup defaults ( Setup ) Setup CMOS Integrated peripherals ( ) COM Port IRQ LPT Port Normal EPP ECP IDE PIO Mode Hardware Monitor Setup ( ), Supervisor password ( ) SETUP CMOS User password ( ) PC BIOS IDE HDD auto detection ( IDE ) IDE CMOS Save & exit setup ( ) SETUP BIOS F10 Exit without save ( SETUP ) <ESC> 25

38 BIOS CMOS STANDARD CMOS SETUP IDE AMIBIOS SETUP STANDARD CMOS SETUP ( C ) 1999 American Megatrends, Inc All Rights Reserved Date (mm/dd/yyyy) : Mon, Sep 06, 1999 Time (hh/mm/ss) : 04:05:37 TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Pri Master Auto Pri Slave Auto Sec Master Auto Sec Slave Auto Floppy Drive A : 144 MB 3½ Base Memory : 640 Kb Floppy Drive B : Not Installed Other Memory : 384 Kb Extended Memory : 63 Mb Boot Sector Virus Protection : Disabled Total Memory : 64 Mb Month : Jan Dec ESC : Exit Day : : Select Item Year : PU / PD / + / :Modify (Shift) F2 : Color Date(mm:dd:yy) ( ) 2: CMOS / / (mm) 1 12 (dd) 1 28/29/30/31 (yy)

39 7IXE4 Time(hh:mm:ss) ( ) : 00 : 00 RTC Pri Master (Slave) / Sec Master (Slave) ( / ) IDE 1 IDE 2 CMOS 1 User TYPE CYLS HEADS SECTORS MODE 2 AUTO TYPE MODE AUTO BIOS POST IDE CYLS HEADS PRECOMP LANDZONE SECTORS Number of cylinders( ) number of heads( ) write precomp Landing zone number of sectors( ) NONE <Enter> Drive A / Drive B ( A:/ B: ) None 360K, 525 in KB 12M, 525 in MB 720K, 35 in 3 720KB 144M, 35 in 3 144MB 288M, 35 in 3 288MB Boot Sector Virus Protection ( ) Enabled Disabled ( ) 27

40 BIOS Memory( ) BIOS POST(Power On Self Test) STANDARD CMOS SETUP Base Memory PC 640KB MS-DOS Extended Memory Base Other Memory Module Other Memory BIOS 384KB BIOS Shadow (Shadow RAM) BIOS Copy DRAM BIOS PC 28

41 7IXE4 BIOS AMIBIOS SETUP BIOS FEATURES SETUP ( C ) 1999 American Megatrends, Inc All Rights Reserved Quick Boot Enabled 1st Boot Device Floppy 2nd Boot Device IDE-0 3rd Boot Device CDROM Try Other Boot Devices Yes Floppy Access Control Read-Write Hard Disk Access Control Read-Write BootUp Num-Lock On Floppy Drive Swap Disabled Floppy Drive Seek Disabled Security Option Setup Boot To OS/2 > 64MB No BIOS Write Protect Disabled C000, 32K Shadow Cached C800, 16K Shadow Disabled CC00, 16K Shadow Disabled ESC: Quit : Select Item D000, 16K Shadow Disabled F1 : Help PU/PD+/-/ : Modify D400, 16K Shadow Disabled F5 :Old Values(Shift)F2:Color D800, 16K Shadow Disabled F6 : Load BIOS Defaults DC00, 16K Shadow Disabled F7 : Load Setup Defaults 3: BIOS Quick Boot BIOS POST Enabled Disabled POST <Esc> Enabled Disabled POST ( ) POST 1st / 2nd / 3rd Boot device ( / / ) Floppy LS/ZIP A: CDROM SCSI NETWORK IDE-0~IDE-3 Disable ATAPI ZIP C: LS/ZIP A: SCSI ATAPI ZIP C: 29

42 30 BIOS

43 7IXE4 Try Other Boot Device Yes ( ) No Floppy Access Control ( ) Read-Write Read-Write ( ) Read-Only Read-Only HDD Access Control ( ) Read-Write Read-Only Read-Write ( ) Read-Only Boot Up Num-Lock On Off ( ) Floppy Drive Swap Enabled Disabled DOS A: B: A: B: ( ) Floppy Drive Seek PC POST FLOPPY SEEK Enabled Disabled Floppy Seek Floppy Seek ( ) Security Option System Setup CMOS SETUP CMOS SETUP ( ) SETUP Enter 31

44 Boot to OS/2>64MB OS2 BIOS No Yes IBM OS/2 ( ) IBM OS2 DRAM 64MB BIOS Write Protect (BIOS ) Enabled Disabled BIOS BIOS ( ) C000 32K Shadow- DC00 16K Shadow ( Shadow), Shadow, 16K ( SCSI ), BIOS, Shadow Enabled Disabled Cached Optional shadow Optional shadow Optional shadow 32

45 7IXE4 AMIBIOS SETUP CHIPSET FEATURES SETUP ( C ) 1999 American Megatrends, Inc All Rights Reserved **** SDRAM Timing **** Config SDRAM Timing Auto *SDRAM PH Limit 32 Cycles *SDRAM Idle Cycle Limit 8 Cycles *SDRAM TRC Bank Cycle Time 7 Cycles *SDRAM TRP SRAS Precharge 2 Cycles *SDRAM TRAS Timing 5 Cycles *SDRAM CAS Latency 3 Cycles *SDRAM TRCD Timing 2 Cycles DRAM Integrity Mode Disabled Memory Hole Disabled DRAM Burst Refresh Enabled Graphics Aperture Size 64MB USB Function Enabled USB KB Legacy Support Disabled ESC: Quit : Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values(Shift)F2:Color F6 : Load BIOS Defaults F7 : Load Setup Defaults 4: * Config SDRAM Timing Manual, 7 Config SDRAM Timing Auto Manual Config SDRAM Timing Auto ( ) Config SDRAM Timing Manual SDRAM PH Limit This function specify the number of consecutive Page-Hit requests to allow before choosing a non-page-hit request 1 Cycle SDRAM PH Limit 1 Cycle 4 Cycle SDRAM PH Limit 4 Cycle 32 Cycle SDRAM PH Limit 32 Cycle ( ) 64 Cycle SDRAM PH Limit 64 Cycle 33

46 BIOS SDRAM Idle Cycle Limit This function specify the number of idle cycles to wait before precharging an idle bank(idle cycles are defined as cycles where no valid request is asserted to the MCT) 0 Cycles SDRAM Idle Limit to 0 Cycles 8 Cycles SDRAM Idle Limit to 8 Cycles ( ) 12 Cycles SDRAM Idle Limit to 12 Cycles 16 Cycles SDRAM Idle Limit to 16 Cycles 24 Cycles SDRAM Idle Limit to 24 Cycles 32 Cycles SDRAM Idle Limit to 32 Cycles 48 Cycles SDRAM Idle Limit to 48 Cycles Disabled SDRAM TRC Bank Cycle Time This function specify the minimum time from activate to activate of the same bank 3 Cycle SDRAM TRC Bank Cycle Time 3 Cycle 4 Cycle SDRAM TRC Bank Cycle Time 4 Cycle 5 Cycle SDRAM TRC Bank Cycle Time 5 Cycle 6 Cycle SDRAM TRC Bank Cycle Time 6 Cycle 7 Cycle SDRAM TRC Bank Cycle Time 7 Cycle ( ) 8 Cycle SDRAM TRC Bank Cycle Time 8 Cycle SDRAM TRP SRAS Precharge This function specify the delay from precharge command to activate command 3 Cycle SDRAM TRP SRAS Precharge 3 Cycle 2 Cycle SDRAM TRP SRAS Precharge 2 Cycle ( ) SDRAM TRAS Timing This function specify the minimum bank (SRAS[2:0]#) active time 2 Cycle SDRAM TRAS Timing Value 2 Cycle 3 Cycle SDRAM TRAS Timing Value 3 Cycle 4 Cycle SDRAM TRAS Timing Value 4 Cycle 5 Cycle SDRAM TRAS Timing Value 5 Cycle ( ) 6 Cycle SDRAM TRAS Timing Value 6 Cycle 7 Cycle SDRAM TRAS Timing Value 7 Cycle 34

47 7IXE4 SDRAM CAS Latency This function specify the delay from SCAS[2:0]# to data valid 2 Cycles SDRAM CAS Latency to 2 Cycles 3 Cycles SDRAM CAS Latency to 3 Cycles( ) SDRAM TRCD Timing 1 Cycle SDRAM Trcd Timing Value 1 Cycle 2 Cycle SDRAM Trcd Timing Value 2 Cycle ( ) 3 Cycle SDRAM Trcd Timing Value 3 Cycle 4 Cycle SDRAM Trcd Timing Value 4 Cycle DRAM Integrity Mode Disabled ECC Disabled this function( ) DRAM Integrity Mode to ECC Memory Hole ( 15M~16M ) Disabled 14MB-15MB 15MB-16MB 14MB-16MB Normal Setting ( ) Address=14~15MB remap to ISA BUS Address=15~16MB remap to ISA BUS Address=14~16MB remap to ISA BUS DRAM Burst Refresh Disabled Enabled Disabled this function Enabled DRAM Burst Refresh function( ) Graphics Aperture Size 4 MB Display Graphics Aperture Size 4MB 8 MB Display Graphics Aperture Size 8MB 16 MB Display Graphics Aperture Size 16MB 32 MB Display Graphics Aperture Size 32MB 64 MB Display Graphics Aperture Size 64MB ( ) 128 MB Display Graphics Aperture Size 128MB 256 MB Display Graphics Aperture Size 256MB 35

48 BIOS USB Function( ) Disabled Enabled USB USB ( ) USB KB Legacy Support USB,USB Disabled Keyb+ Mouse Keyboard Disable USB Legacy Support ( ) USB USB USB 36

49 7IXE4 AMIBIOS SETUP POWER MANAGEMENT SETUP ( C ) 1999 American Megatrends, Inc All Rights Reserved Power Management/APM Enabled Data (of Month) Alarm 15 Video Power Down Mode Suspend Hour Alarm 12 Hard Disk Power Down Mode Suspend Minute Alarm 30 Suspend Time Out (Minute) Disabled Second Alarm 30 Display Activity Ignore Keyboard PowerOn Function Password IRQ3 Both Password for PowerOn Enter IRQ4 Both Mouse PowerOn function Disabled IRQ5 Ignore IRQ7 Both IRQ9 Both IRQ10 Both IRQ11 Both IRQ13 Both IRQ14 Both IRQ15 Both Soft-off by Power Button Instant Off ESC: Quit : Select Item System after AC Back Memory F1 : Help PU/PD+/-/ : Modify Modem Ring On/Wake On Lan Enabled F5 :Old Values(Shift)F2:Color PME Event Wake Up Disabled F6 : Load BIOS Defaults Resume by Alarm Disabled F7 : Load Setup Defaults 5: Power Management / APM( ) Enabled Disabled APM ( ) APM Video Power Down Mode Disabled Suspend, Suspend ( ) Hard Disk Power Down Mode( ) Disabled Suspend, Suspend ( ) 37

50 BIOS Suspend Time Out (Minute) Disabled ( ) 1 1 Suspend 2 2 Suspend 4 4 Suspend 8 8 Suspend Suspend Suspend Suspend Suspend Suspend Suspend Display Activity Ignore Monitor ( ) IRQ[3,4,5,7,8,9,10,11,13,14,15] Ignore Both WakeUp Monitor IRQ to Ignore IRQ to Both IRQ to WakeUP IRQ to Monitor Soft-off by Power Button Instant-off Delay 4 Sec Soft-off ( ) Soft-off 4 System after AC Back, Memory Full-On Soft-Off ( ) Soft PWR button ModemRingOn/WakeOnLan ( / ) Disabled Enabled / / ( ) 38

51 7IXE4 PME Event Wake Up( ) Disabled Enabled ( ) Resume by Alarm( ) Disabled Enabled ( ) : Data(of Month) Alarm : 0~31 Hour Alarm: 0~23 Minute Alarm : 0~59 Second Alarm : 0~59 Keyboard PowerOn Function ( ) Disabled Password Power Key 1-5 ( ) POWER Key, Password for PowerOn Enter 1-5 Mouse PowerOn Function ( ) Disabled Left-button Right-button PS/2 ( ) PS/2 PS/2 39

52 BIOS PCI AMIBIOS SETUP PNP / PCI CONFIGURATION ( C ) 1999 American Megatrends, Inc All Rights Reserved PnP OS Installed No Reset Configuration Data No PCI Latency Timer 64 VGA Boot from AGP PCI VGA Palette Snoop Disabled DMA Channel 0 PnP DMA Channel 1 PnP DMA Channel 3 PnP DMA Channel 5 PnP DMA Channel 6 PnP DMA Channel 7 PnP IRQ 3 PCI/PnP IRQ 4 PCI/PnP IRQ 5 PCI/PnP IRQ 7 PCI/PnP IRQ 9 PCI/PnP IRQ 10 PCI/PnP ESC: Quit : Select Item IRQ 11 PCI/PnP F1 : Help PU/PD+/-/ : Modify IRQ 14 PCI/PnP F5 :Old Values(Shift)F2:Color IRQ 15 PCI/PnP F6 : Load BIOS Defaults F7 : Load Setup Defaults 6: PCI PNP OS Installed PnP Windows 95 Yes No OS PnP ( MS-DOS)( ) Reset Configuration Data BIOS PnP No Yes Reset Configuration Data ( ) ESCD 40

53 7IXE4 PCI Latency Timer 32 PCI Latency Timer to PCI Latency Timer to 64 ( ) 96 PCI Latency Timer to PCI Latency Timer to PCI Latency Timer to PCI Latency Timer to PCI Latency Timer to PCI Latency Timer to 248 VGA Boot from AGP PCI AGP ( ) PCI PCI/VGA Palette Snoop MPEG Enabled Enabled Disabled DMA Channel( 0,1,3,5,6,7 ) ( ) ISA/ EISA PnP ISA EISA PnP ( ) IRQ ( 3,4,5,7,9,10,11,14,15 ) ISA/ EISA PCI / PnP ISA EISA PCI PnP ( ) 41

54 BIOS BIOS AMIBIOS SIMPLE SETUP UTILITY-VERSION 122 ( C ) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD PNP/PCI CONFIGURATION IDE HDD AUTO DETECTION Load BIOS Defaults (Y/N)? LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS Load BIOS Defaults SAVE & EXIT SETUP EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Load BIOS Defaults except Standard CMOS SETUP 7: BIOS Y Enter BIOS 42

55 7IXE4 SETUP AMIBIOS SIMPLE SETUP UTILITY-VERSION 122 ( C ) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS SAVE & EXIT SETUP Load SETUP Defaults (Y/N)? EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Load Setup Defaults except Standard CMOS SETUP Load Setup Defaults 8: SETUP Y Enter Setup 43

56 BIOS AMIBIOS SETUP INTEGRATED PERIPHERALS ( C ) 1999 American Megatrends, Inc All Rights Reserved OnBoard IDE Both OnBoard FDC Auto OnBoard Serial Port A Auto OnBoard Serial Port B Auto Serial PortB Mode Normal *IR Duplex Mode N/A OnBoard Parallel Port Auto Parallel Port Mode ECP **Parallel Port IRQ Auto # Parallel Port DMA Auto 9: * Serial PortB Mode IrDA ** Onboard Parallel Port 378,278,3BC # Onboard Parallel Port 378,278,3BC, Parallel Mode ECP, On Board IDE ( IDE ) ESC: Quit : Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values(Shift)F2:Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Disabled Both Primary Secondary IDE IDE Both( ) IDE Primary IDE Secondary On Board FDC ( ) Enabled Disabled Auto ( ) 44

57 7IXE4 On Board Serial Port A( A) Auto 3F8/COM 1 2F8/COM 2 3E8/COM 3 2E8/COM 4 Disabled BIOS ( ) A 3F8 A 2F8 A 3E8 A 2E8 A Onboard Serial Port B ( B) Auto 3F8/COM 1 2F8/COM 2 3E8/COM 3 2E8/COM 4 Disabled BIOS ( ) B 3F8 B 2F8 B 3E8 B 2E8 B Serial Port B Mode ( I/O IR ) ASKIR I/O ASKIR IrDA I/O IrDA Normal I/O ( ) IR Duplex Mode Half Duplex Full Duplex N/A IR IR ( ) On Board Parallel Port ( ) BC 3BC Auto ( ) Disabled 45

58 BIOS Parallel Port Mode ( ) EPP ECP Normal EPP Enhanced Parallel Port ECP Extended Capabilities Port ( ) Parallel Port IRQ ( IRQ ) 7 Parallel Port IRQ 7 5 Parallel Port IRQ 5 Auto Parallel Port IRQ ( ) Parallel Port DMA ( DMA ) 3 3 Parallel Port DMA 1 1 Parallel Port DMA 0 0 Parallel Port DMA Auto Parallel Port DMA ( ) 46

59 7IXE4 AMIBIOS SETUP PC HEALTH STATUS ( C ) 1999 American Megatrends, Inc All Rights Reserved Reset Case Open Status No 5V SB 4896 V Case Opened No Shut Down Temperature Disabled CPU Temperature Alarm 80 C/ 176 F Current CPU Temperature 34 C/ 93 F CPU Fan Fail Alarm No Power Fan Fail Alarm No System Fan Fail Alarm No Current CPU Fan Speed 5273 RPM Current Power Fan Speed 0 RPM Current System Fan Speed 0 RPM Current System Temp 29 C/ 84 F Vcore 1620 V Vcache 3310 V Vcc V +5000V 5030 V ESC: Quit : Select Item V V F1 : Help PU/PD+/-/ : Modify V V F5 :Old Values(Shift)F2:Color -5000V V F6 : Load BIOS Defaults Battery 3040V F7 : Load Setup Defaults Reset Case Open Status Case Opened Case Opened 10:, Case Opened No, Case Opened YES Case Opened, Reset Case Open Status Yes Shut Down Temperature ( ACPI ) Disabled ( ) 60 C / 140 F CPU 60 C / 140 F, > 60 C / 140 F 70 C / 158 F CPU 70 C / 158 F, > 70 C / 158 F 80 C / 176 F CPU 80 C / 176 F, > 80 C / 176 F 90 C / 194 F CPU 90 C / 194 F, > 90 C / 194 F 47

60 BIOS 48

61 7IXE4 CPU Temperature Alarm (CPU ) Disabled 60 C / 140 F CPU 60 C / 140 F 70 C / 158 F CPU 70 C / 158 F 80 C / 176 F CPU 80 C / 176 F ( ) 90 C / 194 F CPU 90 C / 194 F Current CPU Temperature ( C / F) CPU Fan Fail Alarm (CPU/ Power/System ) Yes No CPU / Power / System CPU / Power / System ( ) Current CPU FAN / System FAN / Power FAN Speed (RPM) Current System Temp ( C / F) Current Voltage (v) Vcore / Vcache / VCC3 / ±12V / ±5V / Battery / 5V SB Vcore / Vcache / VCC3 / ±12V / ±5V / Battery / 5V SB 49

62 BIOS (Supervisor)/ (User) Enter AMIBIOS SIMPLE SETUP UTILITY-VERSION 122 ( C ) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD PNP/PCI CONFIGURATION IDE HDD AUTO DETECTION Enter new supervisor password: LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Change / Set / Disable Password 11: (Supervisor)/ (User) 8 Enter BIOS Enter BIOS PASSWORD DISABLED SUPERVISOR Supervisor BIOS FEATURES SETUP Security option SETUP CMOS SETUP Supervisor USER User BIOS FEATURES SETUP Security option SYSTEM User Supervisor CMOS SETUP USER Password BIOS Supervisor CMOS SETUP 50

63 7IXE4 IDE AMIBIOS SETUP STANDARD CMOS SETUP ( C ) 1999 American Megatrends, Inc All Rights Reserved Date (mm/dd/yyyy) : Fri Dec 25, 1998 Time (hh/mm/ss) : 10:36:24 TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Pri Master : Auto Pri Slave : Auto Sec Master: Auto Sec Slave : Auto Floppy Drive A: 144 MB 3 ½ Floppy Driver B: Not Installed Boot Sector Virus Protection : Disabled Base Memory : 640 kb Other Memory: 384 kb Extended Memory: 31mb Total Memory: 32mb Month: Jan Dec ESC : Exit Day: : Select Item Year : PU/PD/+/ : Modify (Shift)F2 : Color 12: IDE BIOS Mode Normal LBA LARGE BIOS LBA Y STANDARD CMOS CMOS 51

64 BIOS SETUP AMIBIOS SIMPLE SETUP UTILITY-VERSION 122 ( C ) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS SAVE to CMOS SAVE and & EXIT(Y/N)? SETUP Y EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Save Data to CMOS & Exit SETUP 13: SETUP Y Enter RTC CMOS RAM Setup Utility N Esc 52

65 7IXE4 SETUP AMIBIOS SIMPLE SETUP UTILITY-VERSION 122 ( C ) 1999 American Megatrends, Inc All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS PC HEALTH STATUS SUPERVISOR PASSWORD USER PASSWORD PNP/PCI CONFIGURATION IDE HDD AUTO DETECTION Quit without saving(y/n)? N LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Abandon all Datas & Exit SETUP 14: SETUP Y Enter Setup Utility N Esc 53

66 A : AMD A AMD EIDE Driver (TUCD),, (, ICON) 1 AMD EIDE Driver 2 Next (1) (2) 3 Next 4 Next (3) (4) 52

67 7IXE4 6 OK 5 Finish (6) (5) 53

68 B AMD AGP Miniport Driver (TUCD),, (, ICON) 1 AMD AGP Miniport Driver 2 Next (1) (2) AMD AGP Miniport Driver, (4) 3 Finish (3) 54

69 7IXE4 C Gigabyte Utility Manager Ver10 Driver (TUCD),, (, ICON) 1 Gigabyte Utility Manager Ver10 (2) (1) 2 Next 3 Yes (3) (4) 4 Next 5 Next (5) (6) 55

70 56

71 7IXE4 6 Finish (7) (8) Gigabyte Utility Manager Ver10, (9) 57

72 B : BIOS BIOS : BIOS (AMI AWARD) AWDFlashexe AMIFlashexe (D:\>Utility \BIOSFlash) BIOS [ ie: C:\>Utility \ (C: /Utility: )] Win95/98 MS-DOS (Command prompt only), BIOS AWDFlashexe AMIFlashexe BIOS, : C:\Utility \ AWDFlash AMIFlash <BIOS >, Note : website (WWWgigabytecomtw) BIOS BIOS 58