版本：A0

Transcription

1 EPI-1813 基于 Luna Pier Refresh 平台的低功耗 EPI 主板 EPI Motherboard Based on Luna Pier Refresh Platform with Low Power Consumption Version: C00

2 声明本手册包含的内容并不代表本公司的承诺, 本公司保留对此手册更改的权利, 且不另行通知 对于任何因安装 使用不当而导致的直接 间接 有意或无意的损坏及隐患概不负责 订购产品前, 请向经销商详细了解产品性能是否符合您的需求 EVOC 是研祥智能科技股份有限公司的注册商标 本手册所涉及到的其他商标, 其所有权为相应的产品厂家所拥有 研祥智能科技股份有限公司 2010, 版权所有, 违者必究 未经许可, 不得以机械 电子或其它任何方式进行复制 欲获更多信息请访问研祥网站 : 或向研祥技术支持邮箱 咨询

3 安全使用小常识 1. 产品使用前, 务必仔细阅读产品说明书 ; 2. 对未准备安装的板卡, 应将其保存在防静电保护袋中 ; 3. 在从防静电保护袋中拿出板卡前, 应将手先置于接地金属物体上一会儿 ( 比 如 10 秒钟 ), 以释放身体及手中的静电 ; 4. 在拿板卡时, 需佩戴静电保护手套, 并且应该养成只触及其边缘部分的习 惯 ; 5. 为避免人体被电击或产品被损坏, 在每次对主板 板卡进行拔插或重新配 置时, 须先关闭交流电源或将交流电源线从电源插座中拔掉 ; 6. 在需对板卡或整机进行搬动前, 务必先将交流电源线从电源插座中拔掉 ; 7. 对整机产品, 需增加 / 减少板卡时, 务必先拔掉交流电源 ; 8. 当您需连接或拔除任何设备前, 须确定所有的电源线事先已被拔掉 ; 9. 为避免频繁开关机对产品造成不必要的损伤, 关机后, 应至少等待 30 秒后 再开机

4 目录第一章产品介绍...1 简介...1 机械尺寸 重量与环境...1 典型功耗...2 微处理器...2 芯片组...2 系统内存...2 显示功能...2 网络功能...2 音频功能...2 电源特性...3 扩展总线...3 Watchdog 功能...3 I/O 接口...3 第二章安装说明...4 产品外形尺寸图...4 接口位置示意图...5 架构图...6 跳线设置...7 系统内存的安装...8 串口...8 显示接口...9 LCD 背光控制接口...10 音频接口...10

5 SATA 接口...10 SATA 硬盘热插拔 二合一鼠标键盘接口...13 并口...13 USB 接口...14 网络接口...14 状态指示控制接口...15 CF 接口...16 第三章 BIOS 功能简介...17 简介...17 BIOS 参数设置...17 BIOS 基本功能设置...18 x86 平台下 BIOS 所要管理的系统资源...31 第四章驱动程序安装说明...34 附录...35 Watchdog 编程指引...35 常见故障分析与解决...37

6 第一章产品介绍 第一章产品介绍简介 EPI-1813 系列主板是基于 Intel R Luna Pier Refresh 平台开发的符合研祥 EPI2.0 规范的全长卡主板 主板采用板载 Intel R Atom D510( 双核 )/D410( 单核 ) 处理器 + ICH8M 的技术方案实现 此板板载的超低功耗处理器内部集成了内存控制器和图形控制器 板上提供 1 个 SO-DIMM DDR2 插槽和板载 1GB DDR2 内存 ( 板载内存可选 ), 最大内存容量可达 2GB 支持 VGA LVDS 显示 ;2 个 10/100/1000Mbps 网络接口, 其中 LAN1 支持网络唤醒 ;1 个 HDA 音频接口 ;3 个 SATA II 硬盘接口,1 个 CF 卡接口 ;8 个 USB 2.0 接口 ;2 个 COM 口, 其中 COM1 支持 Modem 唤醒 ;1 个并口 ;1 个 PS/2 键盘鼠标接口 ; 扩展符合研祥 EPI2.0 规范 ; 主板采用底板 ATX 电源供电 此产品可广泛应用于环保, 数控, 交通等领域 机械尺寸 重量与环境 外形尺寸 :351.5mm( 长 ) 146.7mm( 宽 ) 30.2mm( 高 ) 净重 :0.45Kg; 工作环境 : 温度 :0 ~60 ; 湿度 :5%~90%( 非凝结状态 ); 贮存环境 : 温度 :-20 ~80 ; 湿度 :5%~90%( 非凝结状态 ); EPI

7 第一章产品介绍 典型功耗 CPU: 板载 Intel R Atom D510 内存 :DDRII 800 MHz 2GB Samsung +5V@1.52A;+5%/-3%; +3.3V@0.55A;+5%/-3%; +12V@0.42A;+5%/-3%; 微处理器 板载 Intel R Atom D510( 双核 )/D410( 单核 ) 处理器, 内部集成了内存 控制器和图形控制器 芯片组 Intel R Atom D510/D410 处理器 + ICH8M 系统内存提供 1 个 SO-DIMM DDR2 插槽和板载 1GB DDR2 内存 ( 板载内存可选 ), 支持 Un-buffered Non-ECC 内存 支持最大内存容量 2GB, 支持的内存频率为 667MHz 显示功能采用 CPU 内置集成图形控制器, 支持 VGA 单通道 18 位 LVDS 显示 VGA 支持最大分辨率及刷新率为 @60Hz;LVDS 支持的最大分辨率为 网络功能 提供 2 个 10/100/1000Mbps 网络接口,LAN1 可支持网络唤醒功能 音频功能采用 ALC888 音效芯片, 支持 HDA, 支持 MIC-in/Line-in/Line-out 功能 EPI-1813

8 第一章产品介绍 电源特性 主板采用底板 ATX 电源供电, 支持 ACPI1.0b 规范, 支持 S0 S1 S4 S5 状态 扩展总线 1 组 EPI 总线扩展连接器, 符合研祥 EPI2.0 规范 通过 EPI 2.0 总线标准底板, 可扩展 PCI 和 ISA 接口 Watchdog 功能 255 级, 可编程按分或秒 ; 支持看门狗超时中断或复位系统 I/O 接口 提供 2 个串口, 支持 RS-232 模式, 采用 2 5pin 插针引出, 其中 COM1 支持 Modem 唤醒功能 ; 提供 1 个并口, 采用 2 13pin 插针引出 ; 提供 3 个 SATA II 接口 ; 提供 1 个 CF 卡接口 (TYPE2 型接口 ); 提供 8 个 USB2.0 接口, 采用 2 5pin 插针引出 ; 提供 1 个 PS/2 接口, 采用二合一接口形式引出 EPI

9 第二章安装说明 第二章安装说明 产品外形尺寸图 H2 H5 H4 H1 H3 单位 :mm 警告! 请务必选择合适的螺钉和使用正确的安装方法 ( 包括板卡定位 CPU 散热器等安装 ), 否则可能损坏板 此板推荐 H1~H5 使用 M3 6 GB 螺钉 EPI-1813

10 第二章安装说明 接口位置示意图 H2 H5 AUDIO1 LAN2 LAN1 VGA1 KM1 COM1 LPT1 COM2 JCC1 USB4 USB3 USB2 USB1 SATA3 SATA2 SATA1 J2 JCF1 CF1 J1 DIMM1 H4 FP1 FP2 FP3 LVDS1 LCDB1 JLCD1 H1 H3 EPI

11 第二章安装说明 架构图 VGA DB15 LVDS 18BIT D510(DC)/ D410(SC)CPU CH A CH A DDR2 Onboard DDR2 SODIMM DDR2 Terminaltion CK505 Clock VRD 11.0 SATA II X3 (1*7) USB 2.0 X8 (Pin header) CF 卡 SATA USB IDE DMI ICH8M 82801HM PCI-E PCI-E SPI RTL8111D RTL8111D SPI Flash LAN1 LAN2 RJ45 Connector RJ45 Connector VCC3_3 VCC1_8 VCC1_05 VCC1_8DDR VCC1_5 VCC5SB VCC3_3SB VCC0_9VTT VCC_GFX Front Panel Circuit EPI 2.0 CONN ISA IT8888 PCI HDA HD Audio (Pin header) PCI LPC BUS W83627DHG Hardware Monitor KB/MS COM1 (RS232) COM2 (RS232) Parallel (Pin header) WDT 提示 : 如何识别跳线 接口第一脚 1 观察插头 插座旁边的文字标记, 通常用 1 或加粗的线条或三角符号表示 2 看看背面的焊盘, 通常方型焊盘为第一脚 EPI-1813

12 第二章安装说明 跳线设置 JCC1:CMOS 内容清除 / 保持设置 ( 脚距 :2.54mm) CMOS 由板上钮扣电池供电 清 CMOS 会导致永久性消除以前系统配置并将其设为原始 ( 工厂设置 ) 系统设置 其步骤 :(1) 关闭计算机, 断开电源 ;(2) 瞬间短接 JCC1 插针 ;(3) 开计算机 ;(4) 启动时按屏幕提示按键进入 BIOS 设置, 重新加载最优缺省值 ;(5) 保存并退出设置 设置方式如下 : 设置 功能 1-2 开路正常工作状态 (Default) JCC1 1-2 短路清除 CMOS 内容, 所有 BIOS 设置恢复成出厂值 JLCD1:LCD 工作电压选择 ( 脚距 :2.54mm) 不同的 LCD 屏电压可能不同, 本板提供了 3.3V 和 5V 两种电压选择, 当所选择的 LCD 电压与所使用的 LCD 屏的工作电压一致时,LCD 屏才能正常显示 设置方式如下 : 设置 功能 1-2 短路 +3.3V(Default) JLCD1 2-3 短路 +5V JCF1:CF 卡工作电压选择 ( 脚距 :2.54mm) 不同的 CF 卡的工作电压可能不同, 本板提供了 3.3V 和 5V 两种电压选择, 当所选择的 CF 卡工作电压与所使用的 CF 卡工作电压一致时, 才能保证系统的稳定性 设置方式如下 : 设置 功能 1-2 短路 +3.3V JCF1 2-3 短路 +5V(Default) EPI

13 第二章安装说明 系统内存的安装本板提供 1 条 200Pin DDRⅡ SO-DIMM 插槽 (DIMM1) 安装内存条时, 要注意以下几点 : 拨开内存槽两边的耳扣, 安装时先将内存条的缺口和内存槽的缺口对准后再向下用力压到位 使用符合该主板 Intel Chipset 所支持的 1.8V DDRⅡ 667MHz 规格的内存, 主板支持最大内存容量达 2GB 最好选择带 SPD( 内存自动识别功能 ) 的内存条, 以保证内存条工作稳定 串口 如下 : 提供 2 个 2 5Pin 插针串口 ( 脚距 :2.54mm), 支持 RS-232 模式, 管脚定义 管脚 信号名称 1 DCD# 2 RXD 3 TXD 4 DTR# 5 GND 6 DSR# COM1,COM2 7 RTS# 8 CTS# 9 RI# 10 NA EPI-1813

14 第二章安装说明 显示接口 1 本板提供 1 个标准 DB15 VGA 接口, 管脚定义如下 : 管脚 信号名称 管脚 信号名称 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND VGA1 7 GND 8 GND 9 +5V 10 GND 11 NC 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK 2 本板提供 1 个单通道 18 位 LVDS 接口 (LVDS1; 脚距 :1.0mm) 管脚定义如下: 管脚 信号名称 管脚 信号名称 1 LVDS_D0+ 2 LVDS_D0-3 GND 4 GND 5 LVDS_D1+ 6 LVDS_D1-7 GND 8 GND 9 LVDS_D2+ 10 LVDS_D2-11 GND 12 GND 13 CLK+ 14 CLK- LVDS1 15 GND 16 GND 17 NC 18 NC 19 VDD 20 VDD EPI

15 第二章安装说明 LCD 背光控制接口 管脚 信号名称 1 VCC_LCDBKLT 2 LCD_BKLTCTL LCDB1 3 LCD_BKLTEN ( 脚距 :2.0mm) 4 GND 注 :VCC_LCDBKLT---+12V 背光电源 ( 此脚电流限制在 1A 以下 ); LCD_BKLTCTL--- 背光控制 ( 该信号由 Pineview D 输出, 为 PWM 信号, 电压幅 值 0V~3.3V, 占空比在 0~100% 之间 ); LCD_BKLTEN ---- 背光使能, 高有效 音频接口 提供 1 个 2 5Pin 插针音频接口 ( 脚距 :2.54mm), 管脚定义如下 : 管脚 信号名称 管脚 信号名称 1 LOUT_R 2 LOUT_L 3 GND_AUDIO 4 GND_AUDIO 5 LIN_R 6 LIN_L AUDIO1 7 GND_AUDIO 8 GND_AUDIO 9 MIC_L 10 MIC_R SATA 接口提供 3 个 SATA 插座, 管脚定义如下 : 管脚信号名称 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ SATA1~SATA3 7 GND EPI-1813

16 第二章安装说明 SATA 硬盘热插拔 SATA 硬盘热插拔需注意 : (1) 硬盘必须支持 :SATA 2.0 接口, 并且采用 15 芯 SATA 硬盘电源接口 (2) 芯片组驱动程序支持 SATA 硬盘的热插拔 (3) 不能对操作系统所在的 SATA 硬盘进行带电热插拔 SATA 硬盘数据线 SATA 硬盘电源线 请按照如下步骤进行 SATA 硬盘热插拔, 否则, 操作不当会导致硬盘损坏和数据丢失 热插入 SATA 硬盘步骤 : 步骤 1: 请将 SATA 电源线 1x4- 针脚 ( 白色 ) 一端接到电源适配器的 1x4- 针脚电源线一端 步骤 2: 将 SATA 数据线接到主板上的 SATA 接口 EPI

17 第二章安装说明 步骤 3: 将 SATA 电源线 15- 针脚接口 ( 黑色 ) 一端接到 SATA 硬盘 步骤 4: 将 SATA 数据线接到 SATA 硬盘 热拔出 SATA 硬盘步骤 : 步骤 1: 从设备管理器中卸载该硬盘 步骤 2: 从 SATA 硬盘一侧拔去 SATA 数据线 步骤 3: 从 SATA 硬盘一侧拔去 SATA 15- 针脚电源线接口 ( 黑色 ) EPI-1813

18 第二章安装说明 二合一鼠标键盘接口 本板提供 1 个二合一鼠标键盘插座 KM1 管脚信号名称 1 KB_DATA 2 MS_DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK 并口 本板提供 1 个 2 13Pin 插针并口 ( 脚距 :2.0mm) LPT1 管脚 信号名称 管脚 信号名称 1 STB# 2 AFD# 3 PD0 4 ERR# 5 PD1 6 INIT# 7 PD2 8 SLIN# 9 PD3 10 GND 11 PD4 12 GND 13 PD5 14 GND 15 PD6 16 GND 17 PD7 18 GND 19 ACK# 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 NC EPI

19 第二章安装说明 USB 接口 本板提供 4 组 2 5Pin 插针的 USB 接口 ( 脚距 :2.54mm), 可连接 8 个标准的 USB 设备 管脚定义如下 : 管脚 信号名称 管脚 信号名称 1 +5V 2 +5V 3 USB1_Data- 4 USB2_Data- 5 USB1_Data+ 6 USB2_Data+ USB1~USB4 7 GND 8 GND 9 NA 10 GND 网络接口本板提供 2 个 10/100/1000Mbps 网络接口 (LAN1 LAN2) 其中 LAN1 支持网络唤醒功能 ACTLED 和 LILED 是以太网接口两边的绿色和双色 LED, 它们显示着 LAN 的活动指示状态和网络速度指示状态 请参考以下每一个 LED 的状态描述 : LAN1 LAN2 ACTLED ( 单色 : 绿色灯 ) 网络活动指示状态 LILED ( 双色 : 橙绿双色 ) 绿色 网络速度指示状态 1000Mbps 闪烁有数据传输橙色 100Mbps 灭无数据传输灭 10Mbps EPI-1813

20 第二章安装说明状态指示控制接口 ATX 电源开关及硬盘指示灯接口 ( 脚距 :2.54mm) 管脚信号名称管脚信号名称 1 PWRBTN# 2 GND FP1 3 GND 4 RESET# 5 HDD_LED- 6 HDD_LED+ 电源指示灯接口 ( 脚距 :2.54mm) 管脚 信号名称 1 PWR_LED+ FP2 2 NC 3 GND 扬声器输出接口 ( 脚距 :2.54mm) 管脚 信号名称 1 SPEAKER 2 NC FP3 3 GND 4 +5V EPI

21 第二章安装说明 CF 接口 本板提供 1 个标准 CF 卡插座 (CF1) 管脚 信号名称 管脚 信号名称 1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS0# 32 CS1# 8 GND 33 VS1# 9 ATASEL# 34 IOR# 10 GND 35 IOW# 11 GND 36 WE# 12 GND 37 IRQ 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 VS2# 16 GND 41 RESET# 17 GND 42 IORDY 18 A2 43 DREQ 19 A1 44 DACK# 20 A0 45 DASP# 21 D0 46 ATA66_DET 22 D1 47 D8 23 D2 48 D9 24 WP/IOCS16# 49 D10 25 CD2# 50 GND EPI-1813

22 第三章 BIOS 功能简介 第三章 BIOS 功能简介简介 BIOS(Basic Input and Output System: 基本输入输出系统 ) 固化在 CPU 板上的闪存存储器中, 主要功能包括 : 初始化系统硬件, 设置各系统部件的工作状态, 调整各系统部件的工作参数, 诊断系统各部件的功能并报告故障, 给上层软件系统提供硬件操作控制接口, 引导操作系统等 BIOS 提供用户一个菜单式的人机接口, 方便用户配置各系统参数设置, 控制电源管理模式, 调整系统设备的资源分配等等 正确设置 BIOS 各项参数, 可使系统稳定可靠地工作, 同时也能提升系统的整体性能 不适当的甚至错误的 BIOS 参数设置, 则会使系统工作性能大为降低, 使系统工作不稳定, 甚至无法正常工作 BIOS 参数设置每当系统接通电源, 正常开机后, 便可看见进入 BIOS 设置程序提示的信息 此时 ( 其它时间无效 ), 按下提示信息所指定的按键 ( 通常为 <Del> 键 ) 即可进入 BIOS 设置程序 CMOS 中 BIOS 设置内容被破坏时, 系统也会要求进入 BIOS 设置或选择某种默认设置值 通过 BIOS 修改的所有设置值都保存在系统的 CMOS 存储器中, 该 CMOS 存储器由电池供电, 即使切断外部电源, 其内容也不会丢失, 除非执行清除 CMOS 内容的操作 注意!BIOS 的设置直接影响到电脑的性能, 设置错误的参数将造成电脑的损坏, 甚至不能开机, 请清 CMOS 后再使用 BIOS 内置缺省值来恢复系统正常运行 由于本公司不断研发更新 BIOS, 其设置界面也会略有不同, 以下的画面供您参考, 有可能跟您目前所使用的 BIOS 设置程序不完全相同 EPI

23 第三章 BIOS 功能简介 BIOS 基本功能设置 当 SETUP 程序启动之后, 您可以看到 CMOS Setup Utility 主画面如下 : System Overview Processor Type : Intel(R) Atom(TM) CPU D510 Speed :1666MHz Cores :2 BIOS SETUP 1.66GHz Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit System Memory Size :1015MB System Time [00:47:55] System Date [Mon 01/11/2010] V02.57 (c)copyright ,American Megatrends, Inc. Main System Time 选择此选项, 用 < + > / < - > 来设置目前的时间 以时 / 分 / 秒的格式来表示 各项目合理的范围是 :Hour/ 时 (00-23), Minute/ 分 (00-59),Second/ 秒 (00-59) System Date 选择此选项, 用 < + > / < - > 来设置目前的日期 以月 / 日 / 年的格式来表示 各项目合理的范围是 :Month/ 月 (Jan.-Dec.), Date/ 日 (01-31),Year/ 年 ( 最大至 2099), Week/ 星期 (Mon.~ Sun.) EPI-1813

24 第三章 BIOS 功能简介 Advanced Advanced Settings BIOS SETUP UTILITY Configure CPU WARNING:Setting wrong values in below sections may cause system to malfunction CPU Configuration IDE Configuration Super I/O Configuration ISA I/O Decode Configuration ISA Memory Decode Configuration Hardware Health Configuration USB Configuration Power Management Configuration Clock Generator Configuration Select Screen Select Item Enter Go to Sub Screen Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. CPU Configuration BIOS SETUP UTILITY Configure advanced CPU settings Brand String: Intel(R) Atom(TM) CPU 1.66GHz Frequency; :1.66GHz FSB Speed; :667MHz Cache L1; :48 KB Cache L2; :1024 KB Ratio Actual Value :10 Hyper Threading Technology [Enabled] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc Hyper Threading Technology Intel Hyper Threading Technology 功能的控制开关 EPI

25 第三章 BIOS 功能简介 IDE Configuration BIOS SETUP UTILITY IDE Configuration ATA/IDE Configuration Configure SATA as Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Third IDE Slave [Enhanced] [IDE] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. ATA/IDE Configuration 此选项用来配置 ATA 的工作模式,Enhanced 和 Compatible 分别对应增强模式和兼容模式 Configure SATA as SATA 控制器的类型选择, 对应 IDE 和 AHCI 选择项, 仅在 ATA/IDE Configuration 为增强模式时才支持 AHCI AHCI 功能同时需要硬件芯片和操作系统支持 Legacy IDE Channels 配置兼容模式下 IDE 通道类型, 对应 SATA Only,SATA Pri,PATA Sec 和 PATA Only 选择项 Primary~Third IDE Master/Slave * Type Not Installed: 系统没有检测到 IDE 设备 AUTO: 系统开机自动检测 IDE 参数 EPI-1813

26 第三章 BIOS 功能简介 CD/DVD: 用于 ATAPI CDROM ARMD: 用于各种模拟 IDE 设备* LBA/Large Mode 用于设置是否支持 LBA 模式 * Block(Multi-sector Transfer) 用于设置是否支持多扇区同时传输的功能 * PIO Mode 用于 PIO 模式设置 * DMA Mode 用于 DMA 模式设置 * S.M.A.R.T 此选项用于设置是否启用硬盘 S.M.A.R.T 功能, 只对支持该功能的硬盘有效 * 32Bit Data Transfer 此选项用于使能 32 位的硬盘访问模式, 可以使硬盘读写速度达到最佳 AHCI Port0~2 AHCI 端口配置菜单, 仅在 SATA 控制器配置成 AHCI 或 RAID 时显示 * SATA Port0~2 Auto: 系统开机自动检测 SATA 设备 Not Installed: 关闭该端口, 不做检测 * S.M.A.R.T 此选项用于设置是否启用硬盘 S.M.A.R.T 功能, 只对支持该功能的硬盘有效 EPI

27 第三章 BIOS 功能简介 Super I/O Configuration Configure Super I/O Chipset Floppy A BIOS SETUP UTILITY [Disabled] OnBoard Floppy Controller [Enabled] Serial Port1 Address Serial Port2 Address Parallel Port Address [378] Parallel Port Mode Parallel Port IRQ Floppy A [3F8/IRQ4] [2F8/IRQ3] [Normal] [IRQ7] Allows BIOS to Enable or Disable Floppy Controller. Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. 软盘驱动器类型配置 OnBoard Floppy Controller 用于使能软驱控制器 Serial Port 1 Address ( 缺省值为 3F8H/IRQ4), 设定主机板上串口 1 的地址及 IRQ, 选項有 : Disabled 3F8H/IRQ4 3E8/IRQ4 2E8/IRQ3 2F8H/IRQ3 Serial Port 2 Address ( 缺省值为 2F8H/IRQ3), 设定主机板上串口 2 的地址及 IRQ, 选項有 : Disabled 3F8H/IRQ4 3E8/IRQ4 2E8/IRQ3 2F8H/IRQ3 Parallel Port Address 设定主机板上并口的地址, 地址缺省值为 378 Parallel Port Mode 设定主机板上并口的模式 Parallel Port IRQ 设定主机板上并口的中断 EPI-1813

28 第三章 BIOS 功能简介 ISA I/O Decode Configuration BIOS SETUP UTILITY Configure ISA I/O Address Decode I/O Space 0 Decode I/O Base 0 Decode I/O Size 0 Decode I/O Space 1 Decode I/O Base 1 Decode I/O Size 1 Decode I/O Space 2 Decode I/O Base 2 Decode I/O Size 2 Decode I/O Space 3 Decode I/O Base 3 Decode I/O Size 3 Decode I/O Space 4 Decode I/O Base 4 Decode I/O Size 4 Decode I/O Space 5 Decode I/O Base 5 Decode I/O Size 5 [Enabled] [0100h] [64 Bytes] [Enabled] [0140h] [32 Bytes] [Enabled] [0200h] [128 Bytes] [Enabled] [0300h] [64 Bytes] [Enabled] [0340h] [32 Bytes] [Enabled] [0A70h] [16 Bytes] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. Decode I/O Space(0-5) IO 解码空间开关 (n) Decode I/O Base(0-5) IO 解码空间基地址 Decode I/O Size(0-5) IO 解码空间大小 EPI

29 第三章 BIOS 功能简介 ISA Memory Decode Configuration Configure ISA Memory Address Memory Space 0 Memory Space 1 Memory Space 2 Memory Space 3 BIOS SETUP UTILITY [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. Memory Space(0-3) Memory 解码空间开关 Decode MEM Base(0-3) Memory 解码空间基地址 Decode Size(0-3) Memory 解码空间大小 Hardware Health Configuration BIOS SETUP UTILITY Hardware Health Configuration System Temperature : 30 /86 CPU Temperature : 37 /98 Vcore : V V3.3 : V V5.0 : V V12.0 : V VBAT : V Enables Hardware Health Monitoring Device Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc EPI-1813

30 第三章 BIOS 功能简介 System Temperature 当前系统温度, 一般主板上有热敏电阻监测 CPU Temperature 当前 CPU 温度 CPU 的温度由板上的温度传感器监测 Vcore CPU 核心电压 V3.3/ V5.0/ V12.0 开关电源输出电压 VBAT 电池电压监测 USB Configuration USB Configuration USB Devices Enabled : BIOS SETUP UTILITY Enables USB host controllers. 1 Keyboard, 1 Drive Select Screen USB Function [8 USB Ports] Select Item USB 2.0 Controller [Enabled] + - Change Field Legacy USB Support [Auto] F1 General Help F10 Save and Exit USB Mass Storage Device Configuration ESC Exit V02.57 (c)copyright , American Megatrends, Inc. USB Function 此选项设置 USB 控制器的数量, 即确定支持几个 USB 控制器, 通常一个控制 器有两个 USB 接口 USB 2.0 Controller 此选项用来选择是否支持 USB 2.0 控制器 EPI

31 第三章 BIOS 功能简介 Legacy USB Support 此选项用于支持传统的 USB 设备 ( 键盘, 鼠标, 存储设备等 ), 当该项设为 Enabled 时, 即使不支持 USB 的操作系统如 DOS 下也能使用 USB 设备 USB Mass Storage Device Configuration 此选项用于配置 USB 块存储设备, 其中包括 Reset 延时设置及枚举类型 Power Management Configuration BIOS SETUP UTILITY Power Management Configuration ACPI APIC Support [Enabled] Restore on AC Power Loss [Last state] Resume on RTC Alarm [Disabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. ACPI APIC Support 此选项用于打开或关闭 ACPI OS 下的 APIC( 高级中断控制器 ) Restore on AC Power Loss 使用该选项可以设置计算机在交流电停电而后再来电时系统所处状态 Power Off, 让系统处于关机状态, Power On, 系统自动开启, Last State, 则保持到断电前的状态 Resume on RTC Alarm 此项用来打开或关闭系统闹钟, 当到达指定时间时, 会将系统从节电模式甚至关机状态唤醒, 该功能必须有 ATX 电源的支持 EPI-1813

32 第三章 BIOS 功能简介 Clock Generator Configuration BIOS SETUP UTILITY Configure Clock Generator Spread Spectrum [Enabled] Auto PCI Clock [Enabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Spread Spectrum 此选项用来控制时钟信号的展频功能 Auto PCI Clock 此选项用来实现 PCI 槽上设备的自动侦测, 如果槽上无设备, 则关闭该槽对应的时钟信号 Chipset BIOS SETUP UTILITY Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction. North Bridge Chipset Configuration DRAM Frequency [Auto] Configure DRAM Timing by SPD [Enabled] Initiate Graphic Adapter Boot Display Device Flat Panel Type UserDefine Panel Type South Bridge Chipset Configuration Onboard Audio Controller [Enabled] Select Screen Select Item [PCI/IGD] Enter Go to Sub Screen [CRT+LVDS] F1 General Help [800x600/S/18/G104S] F10 Save and Exit [Disabled] ESC Exit V02.57 (c)copyright , American Megatrends, Inc. EPI

33 第三章 BIOS 功能简介 DRAM Frequency 配置 DRAM 的频率, 此处建议使用自动, 手动更改配置可能会因为 DRAM 不支持而不开机 Configure DRAM Timing by SPD BIOS 按照 SPD 芯片上的内容配置 SDRAM 内存的时序 绝大多数内存条上有一个保存内存时序和容量等参数的一个小芯片, 即 SPD 芯片 Initiate Graphic Adapter 此选项用于指定优先启动的显示设备类型 Boot Display Device 此选项用于选择开机默认的显示输出设备 Flat Panel Type 此选项用于选择 Flat Panel 的分辨率 UserDefine Panel Type 可以根据用户自定义配置平板显示类型 Onboard Audio Controller 选择是否打开声卡控制器 PCIPnP BIOS SETUP UTILITY Advanced PCI/PnP Settings WARNING:Setting wrong values in below sections may cause system to malfunction. IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] V02.57 (c)copyright , American Megatrends, Inc. Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit EPI-1813

34 第三章 BIOS 功能简介 IRQ3~15 此系列选项用以指定对应 IRQ 号是 PNP 方式还是保留给 ISA 使用 Boot BIOS SETUP UTILITY Boot Settings Quick Boot [Enabled] Quiet Boot [Disabled] Waite For F1 If Error [Enabled] Boot Device Priority 1 st Boot Device [USB:aigo USB DISK] Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Quick Boot 配置在 BIOS 引导期间是否允许跳过某些项的测试, 减少 BIOS 引导时间 Quiet Boot 配置是否显示 OEM LOGO 内容 Wait For F1 If Error 配置在系统出错时是否提示按 F1 键 1st~4th Boot Device 配置系统启动时优先权高低的启动设备 EPI

35 第三章 BIOS 功能简介 Security Security Settings Supervisor Password User Password Change Supervisor Password Change User Password BIOS SETUP UTILITY :Not Installed :Not Installed Install or Change the password Select Screen Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Change User/ Supervisor Password 当按 Change User/ Supervisor Password 后, 在对话框中输入新的密码后, 此栏会显示用户密码已安装 Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults South Bridge Configuration Exit system setup after saving the changes. Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Save Changes and Exit 当您完成了所有的修改操作, 想将原来的设置参数覆盖掉时, 可执行此项功能, 新的设置参数将保存在 CMOS 的存储器中 要执行此操作, 先选定此选项并 按下 < Enter > 键, 再按 < Enter > 键即可可退出 EPI-1813

36 第三章 BIOS 功能简介 Discard Changes and Exit 当您所做的任何更改设置的动作不想存入 CMOS 的存储器中, 可先选定此选项并按下 < Enter > 键, 再按 <Enter > 键即可退出 Discard Changes 当您所做的任何更改设置的动作有误而需要忽略时, 可先选定此选项并按下 < Enter > 键, 然后可以再次进入相应选项进行重新设置 Load Optimal Defaults 此菜单用于在你的系统配置中装入缺省值 这些缺省设置是最优的, 可以发挥所有硬件的高性能 Load Failsafe Defaults 该选项的功能是将各项设置初始化为实现最基本的和最安全的系统功能的值 要执行此项功能, 先选中此选项按下 < Enter > 即可, 接着系统会在屏幕上显示出要您确认的信息, 按下 < Enter > 键确定执行该项功能 x86 平台下 BIOS 所要管理的系统资源 这里的系统资源我们定义三种 :I/O 端口地址,IRQ 中断号和 DMA 号 DMA 级别 功能 DMA0 DRAM 刷新 DMA1 未分配 DMA2 未分配 DMA3 未分配 ( 有时用于硬盘 ) DMA4 用于 DMAC 的级联 DMA5 未分配 DMA6 未分配 DMA7 未分配 EPI

37 第三章 BIOS 功能简介 APIC 高级可编程中断控制器 在现代 P4 以上级别的主板中, 大都支持 APIC, 可以提供多于 16 个中断源, 如 IRQ16 IRQ23, 部分主板如支持 PCI-X 的主板可以有多达 28 个中断源 但要启用该功能必须相应的操作系统支持, 目前只有 windows 2000 以上的操作系统支持 IO 端口地址 系统 I/O 地址空间总共有 64K, 每一外围设备都会占用一段 I/O 地址空间 下 表给出了本 CPU 卡部分设备的 I/O 地址分配, 由于 PCI 设备 ( 如 PCI 网卡 ) 的地址 是由软件配置的, 表中没有列出 地址 设备描述 000h - 00Fh DMA 控制器 #1 020h - 021h 可编程中断控制器 #1 040h - 043h 系统计时器 060h - 064h 标准 101/102 键盘控制器 070h - 071h 实时时钟,NMI 080h - 09Fh DMA 页寄存器 0A0h - 0A1h 可编程中断控制器 #2 0C0h - 0DFh DMA 控制器 #2 0F0h 0FFh 数据数值处理器 1F0h - 1F7h 主要 IDE 通道 274h 279h,A79h PnP 组态寄存器端口 2F8h - 2FFh 串行端口 #2(COM2) 378h - 37Fh 并行端口 #1(LPT1) 3F6h - 3F6h 主要 IDE 通道 3F8h - 3FFh 串行端口 #1(COM1) 400h 41Fh SMBus 控制器 EPI-1813

38 第三章 BIOS 功能简介 IRQ 中断分配表 系统共有 15 个中断源, 有些已被系统设备独占 只有未被独占的中断才可分配给其它设备使用 ISA 设备要求独占使用中断 ; 只有即插即用 ISA 设备才可由 BIOS 或操作系统分配中断 而多个 PCI 设备可共享同一中断, 并由 BIOS 或操作系统分配 下表给出了 X86 平台部分设备的中断分配情况, 但没有给出 PCI 设备所占用的中断资源 级别 功能 IRQ0 IRQ1 IRQ2 系统计时器 标准 101/102 键或 Microsoft 键盘 可编程的中断控制器 IRQ3 串口 #2 IRQ4 串口 #1 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 保留保留给软驱控制器并口系统 CMOS/ 实时时钟 ACPI 保留保留 PS/2 鼠标数学协处理器主 IDE 保留 EPI

39 第四章驱动程序安装说明 第四章驱动程序安装说明 本产品的驱动程序可依据配套光盘内容安装, 在此不做介绍 EPI-1813

40 附录 附录 Watchdog 编程指引本板提供一个可按分或按秒计时的, 最长达 255 级的可编程看门狗定时器 ( 以下简称 WDT) 通过编程,WDT 超时事件可用来将系统复位或者产生一个可屏蔽中断 本主板可使用的中断号为 :3,4,5,7,9,10,11 使用前请把 BIOS Setup 界面 PCIPnP 组中对应的 IRQ 号选项值改成 Reserved 以下用 C 语言形式提供了 WDT 的编程范例, 对 WDT 的编程需遵循以下步骤 : 进入 WDT 编程模式 设置 WDT 工作方式 / 启动 WDT/ 关闭 WDT (1) 进入 WDT 编程模式 #define INDEX_PORT #define DATA_PORT 0x2E 0x2F outportb(index_port, 0x87); outportb(index_port, 0x87); outportb(index_port, 0x07); outportb(data_port, 0x08); outportb(index_port, 0x30); outportb(data_port, 0x01); (2) 配置 WDT 工作方式, 复位或中断方式, 选择一种 : unsigned char oldval; outportb(index_port,0x2d); oldval = inportb(data_port); a. 配置 WDT 成复位工作方式 oldval &= 0xfe; outportb(data_port, oldval); EPI

41 附录 b. 配置 WDT 成中断工作方式 oldval = 0x01; outportb(data_port, oldval); outportb(index_port,0xf7); outportb(data_port, IRQ_NO); /* 此处请用需要使用的中断号替换掉常量 IRQ_NO, 文档前端已经列出可使用中断号的范围 */ (3) 配置 WDT 按分或秒计时 : a. 按分计时 : outportb(index_port,0xf5); outportb(data_port,0x08); b. 按秒计时 : outportb(index_port,0xf5); outportb(data_port,0x00); (4) 启动 / 禁止 WDT a. 启动 WDT: outportb(index_port,0xf6); outportb(data_port,time_out_value); /* 请以超时时间单位数量 (0x01~0xFF) 替换掉常量 TIME_OUT_VALUE*/ b. 停止 WDT: outportb(index_port,0xf6); outportb(data_port,0x00); EPI-1813

42 附录 常见故障分析与解决 序号故障现象故障分析解决 BIOS 设置不能保存时可开机时不可开机当接上 U 盘时, 系统提示一个高速设备接到一个低速接口上 分析 : 可能是 CMOS 电池的问题 解决方法 : 用万用表测量 CMOS 电池, 电压不足就更换新电池, 重新设置保存 分析 : 可能是电源接触不良, 从主板电源插座上拔下电源, 发现主板电源插针某根插针经多次用力插压, 已经倒向一边 解决方法 : 关机拔下电源插头, 用镊子将弯曲的电源插针弄直插上电源开关, 重新启动, 多次试验, 没有出现此类故障 分析 :U 盘是高速 USB2.0, 接到电脑上有提示一个高速设备接到一个低速接口上, 说明主板的接口被认为是一个 USB1.1 的接口 解决方法 : 将主板上 USB 高速传输模式打开即可 不同的主板有不同的设置 一般是将 USB 设备选项中的 FULLSPEED 改为 HISPEED 即可 4 更换新内存后屏幕无显示, 呈现黑屏状态, 无法正常进入系统, 换上原来的内存仍然无法启动 分析 : 可能是由于在插拨内存的过程中操作不当引起主板上部件工作不正常, 需要重点检查主板上与内存相关的电路 解决方法 : 首先检查内存 显卡等硬件, 结果显示这些硬件都没有问题, 都可以正常使用 仔细检查主板上内存插槽周围的电路, 最终发现第一个内存插槽里的两根与内存金手指接触的针脚搭在一起, 对照第二个内存插槽没有该现象, 由此判断是第一个内存插槽短路了 用镊子小心地将两根针脚拨回原处, 插上内存, 重新启动, 系统顺利启动 EPI

43 附录 序号 故障现象 故障分析解决分析 : 可能是由于在安装光驱时不小心碰撞了硬盘的数据线, 从而使硬盘数据线接口接触不良导致的, 或者是硬盘和光驱上的主从跳线设置不正确 5 解决方法 : 首先对硬盘数据线和硬盘及主板上的更换光驱后系统 IDE 接口进行检查, 发现没有问题 ; 然后检查主从无法启动跳线的设置, 发现硬盘和光驱连接在不同的数据线 上, 而且硬盘和光驱的跳线都设置为主盘, 从而导 致硬盘无法启动 ; 将光驱的跳线设置为从盘, 重新 安装好 分析 : 确认 PCI 卡功能是否正常 ; 将 PCI 卡重插或 插入其他 PCI 插槽, 看能否正常 ; 了解使用的电源 类型 ( 是 AT 还是 ATX); 了解客户的 PCI 卡的电压 需求 6 解决方法 : 如 PCI 卡功能问题, 更换 PCI 卡解决 ; 进入系统后无法重插或插入其他 PCI 插槽即可正常, 则为 PCI 卡与检测到 PCI 卡插槽接触问题 如果使用的是 AT 电源, 但 PCI 卡 需要 3.3V 电压, 因为 AT 电源不提供 3.3V 电压, 电源需更换为 ATX 电源方可使用 PCI 卡 ( 建议 : 在选购电源时, 先了解所使用的 PCI 卡是否需要 3.3V 电压 ) 分析 : 没有连接 ; 没有装驱动 ; 设备已坏 7 找不到外接设备 解决方法 : 查看设备与主板的连接线是否正常, 如正常则更换正常连接线确定连接无问题 ; 重新安装设备驱动, 看是否可以识别 ; 检测设备是否正常 ; 如设备正常考虑与主板是否兼容 EPI-1813

44 Announcement What contained in this User Manual does not represent the commitments of EVOC Company. EVOC Company reserves the right to revise this User Manual, without prior notice, and will not be held liable for any direct, indirect, intended or unintended losses and/or hidden dangers due to installation or improper operation. Before purchasing, please have a detailed understanding of the product performance to see whether it meets your requirements. EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. All trademarks, registered trademarks, and trade names used in this User Guide are the property of their respective owners. EVOC Intelligent Technology Co., Ltd. 2010, Copyright Reserved. No part of this manual can be reproduced in any form or by any means, such as in electronic or mechanical way, without permission in writing from EVOC. Please visit our website: for more information; or please send to the Technical Support Mailbox support@evoc.com, support@evoc.cn for consultation.

45 Safety Instructions 1. Before handling your product, read the user s manual carefully; 2. Any board or card not ready to be installed shall be kept in the anti-static packaging; 3. Before taking board or card from anti-static packaging, put your hand on grounded metal object for a while (about 10 seconds) to eliminate static on your body; 4. While holding a board or card, please do wear static protective gloves; always hold a board by its edges; 5. Before inserting, removing or re-configuring motherboard or expansion card, first disconnect the computer and peripherals from their power sources; 6. Before removing boards or computer, turn off all power resources firstly and disconnect the power cord from power source; 7. For PC Box products, when inserting or removing boards, disconnect the computer and peripherals from the power sources firstly; 8. Before connecting or unplugging any equipment, make sure all power cords are unplugged in advance; 9. To avoid unnecessary damage caused by turning on/off computer frequently, wait at least 30 seconds before re-turning on the computer.

46 Table of Contents Chapter 1 Product Introduction...1 Overview...1 Mechanical Dimension, Weight and Environment...1 Typical Consumption...2 Microprocessor...2 Chipset...2 System Memory...2 Display Function...2 LAN Function...3 Audio Function...3 Power Feature...3 Expansion Bus...3 Watchdog Function...3 I/O Connector...3 Chapter 2 Installation...4 Product Outline...4 Locations of Connectors...5 Structure...6 Jumper Setting...7 Install System Memory...8 Serial Port...8 Display Connector...9

47 LCD Backlight Control Connector...10 Audio Connector...10 SATA Connector...10 Hot-swap of SATA Hard Disk in-1 Mouse and Keyboard Connector...13 Parallel Port...13 USB Port...14 LAN Port...14 Status Indicator and Control Connector...15 CF Socket...16 Chapter 3 BIOS Setup...17 BIOS Overview...17 BIOS Parameter Setup...17 Basic Function Setting for BIOS...18 System Resource Managed by BIOS under X86 Platform...31 Chapter 4 Install the Drivers...34 Appendix...35 Watchdog Programming Guide...35 Troubleshooting and Solutions...37

48 Chapter 1 Product Introduction Chapter 1 Product Introduction Overview EPI-1813 series is a full-size motherboard, which is developed basing on Intel c Luna Pier Refresh platform and is compliant with EVOC EPI2.0 specification. The motherboard adopts Intel R Atom D510 (dual-core) / D410 (single-core) processor + ICH8M technique scheme on-board. The on-board ultra-low power consumption processor interior integrates memory controller and graphic controller. It provides one SO-DIMM DDR2 slot and on-board 1GB DDR2 memory (the on-board memory is optional), up to 2GB. It supports VGA and LVDS display; two 10/100/1000Mbps LAN ports, LAN1 supports Wake-on-LAN function; one HDA audio connector; three SATA II hard disk connectors; one CF card connector; eight USB 2.0 ports; two COMs, COM1 supports Modem wake-up function; one parallel port; one PS/2 keyboard and mouse connector; expansion is compliant with EVOC EPI2.0 specification; the motherboard adopts ATX power supply from carrier. The product can be widely applied in the fields such as environment protection, numerical control and transportation, etc. Mechanical Dimension, Weight and Environment Dimension: 351.5mm (L) 146.7mm (W) 30.2mm (H); Net Weight: 0.45Kg; Operating Environment: Temperature: 0 ~ 60 ; Humidity: 5% ~ 90% (non-condensing); Storage Environment: EPI

49 Chapter 1 Product Introduction Temperature: -20 ~ 80 ; Humidity: 5% ~ 90% (non-condensing); Typical Consumption CPU: on-board Intel R Atom D510 Memory: DDRII 800 MHz 2GB Samsung +5V@1.52A; +5%/-3%; +3.3V@0.55A; +5%/-3%; +12V@0.42A; +5%/-3%; Microprocessor Intel R Atom D510 (dual-core)/d410 (single-core) processor on-board, interior integrates memory controller and graphic controller. Chipset Intel R Atom D510/D410 processor + ICH8M; System Memory Provide one SO-DIMM DDR2 slot and on-board 1GB DDR2 memory (the on-board memory is optional), support Un-buffered Non-ECC memory. The maximum memory capacity supported is up to 2GB while the supported memory frequency is 667MHz. Display Function Adopt CPU built-in integrated graphic controller, support VGA and single-channel 18-bit LVDS display. The maximum resolution and refresh frequency supported by VGA is @60Hz while the maximum resolution supported by LVDS is EPI-1813

50 Chapter 1 Product Introduction LAN Function Provide two 10/100/1000Mbps LAN ports; LAN1 supports Wake-on-LAN function. Audio Function Adopt ALC888 sound effect chip, support HDA and MIC-in/Line-in/Line-out function. Power Feature The board adopts ATX power supply from carrier, support ACPI1.0b specification and the status of S0, S1, S4 and S5. Expansion Bus A set of EPI bus expansion connector comply with EVOC EPI2.0 specification. It can expand PCI and ISA connectors via standard EPI 2.0 bus carrier. Watchdog Function 255 levels, programmable by minute or second; Support watchdog timeout interrupt or reset system. I/O Connector Two RS-232 COMs, educed out via 2 5pin headers; COM1 supports Modem wake-up function; One parallel port, educed out via 2 13pin header; Three SATA II connectors; One CF card connector (TYPE2 connector); Eight USB2.0 ports, educed out via 2 5pin headers; One PS/2 connector, educed out via a 2-in-1 connector. EPI

51 Chapter 2 Installation Chapter 2 Installation Product Outline H2 H5 H4 H1 H3 Unit: mm Warning! Please adopt appropriate screws and proper installation methods (including board allocation, CPU and heat sink installation, etc); otherwise, the board may be damaged. It is recommended to use M3 6 GB screws at H1 ~ H EPI-1813

52 Chapter 2 Installation Locations of Connectors H2 H5 AUDIO1 LAN2 LAN1 VGA1 KM1 COM1 LPT1 COM2 JCC1 USB4 USB3 USB2 USB1 SATA3 SATA2 SATA1 J2 JCF1 CF1 J1 DIMM1 H4 FP1 FP2 FP3 LVDS1 LCDB1 JLCD1 H1 H3 EPI

53 Chapter 2 Installation Structure VGA DB15 LVDS 18BIT D510(DC)/ D410(SC)CPU CH A CH A DDR2 Onboard DDR2 SODIMM DDR2 Terminaltion CK505 Clock VRD 11.0 SATA II X3 (1*7) USB 2.0 X8 (Pin header) CF 卡 SATA USB IDE DMI ICH8M 82801HM PCI-E PCI-E SPI RTL8111D RTL8111D SPI Flash LAN1 LAN2 RJ45 Connector RJ45 Connector VCC3_3 VCC1_8 VCC1_05 VCC1_8DDR VCC1_5 VCC5SB VCC3_3SB VCC0_9VTT VCC_GFX Front Panel Circuit EPI 2.0 CONN ISA IT8888 PCI HDA HD Audio (Pin header) PCI LPC BUS W83627DHG Hardware Monitor KB/MS COM1 (RS232) COM2 (RS232) Parallel (Pin header) WDT Tip: How to identify the first pin of the jumpers and connectors 1. Observe the letter beside the socket, it would be marked with 1 or thickened lines or triangular symbols; 2. Observe the solder pad on the back, the square pad is the first pin; EPI-1813

54 Chapter 2 Installation Jumper Setting JCC1: Clear/Keep CMOS Setting (Pin Distance: 2.54mm) CMOS is powered by the button battery on board. Clear CMOS will restore original settings (factory default). The steps are listed as follows: (1) Turn off the computer and unplug the power cable; (2) Instantly short circuit JCC1; (3) Turn on the computer; (4) Follow the prompt on screen to enter BIOS setup when booting the computer, load optimized defaults; (5) Save and exit. Please set as follows: Setup Function 1-2 Open Normal (Default) JCC1 1-2 Short Clear the contents of CMOS, all BIOS setting will restore to factory default values. JLCD1: Select LCD Operating Voltage (Pin Distance: 2.54mm) Different LCD screens have different voltages; the board provides two voltage options, 3.3V and 5V. Only when the selected LCD voltage is in accord with the LCD voltage in use, can the LCD screen display normally. Please set as follows: Setup Function 1-2 Short +3.3V(Default) JLCD1 2-3Short +5V JCF1: Select CF Card Operating Voltage (Pin Distance: 2.54mm) Different CF cards have different operating voltages; the board provides two voltage options, 3.3V and 5V. Only when the selected CF card operating voltage is in accord with the CF card operating voltage in use, can the system stability be ensured. Please set as follows: Setup Function 1-2 Short +3.3V JCF1 2-3 Short +5V(Default) EPI

55 Chapter 2 Installation Install System Memory The board provides one 200Pin DDRII SO-DIMM memory slot (DIMM1). Pay attention as follows when installing the memory bank: Open the buckles beside the memory slot. During installation, aim at the gaps between memory bank and memory slot and press properly to connect them; The 1.8V DDRII 667MHz memory supported by Intel Chipset can be used; the maximum memory capacity is up to 2GB. It is recommended to use memory bank with SPD to ensure stable operation. Serial Port Provide two 2 5Pin RS-232 serial ports (Pin Distance: 2.54mm); the pin definitions are as follows: Pin Signal Name 1 DCD# 2 RXD 3 TXD 4 DTR# 5 GND 6 DSR# COM1/COM2 7 RTS# 8 CTS# 9 RI# 10 NA EPI-1813

56 Chapter 2 Installation Display Connector 1. The board provides one standard DB15 VGA connector; the pin definitions are as follows: Pin Signal Name Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND VGA1 7 GND 8 GND 9 +5V 10 GND 11 NC 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK 2. The board provides one single-channel 18-bit LVDS connector (LVDS1; Pin Distance: 1.0mm). The pin definitions are as follows: Pin Signal Name Pin Signal Name 1 LVDS_D0+ 2 LVDS_D0-3 GND 4 GND 5 LVDS_D1+ 6 LVDS_D1-7 GND 8 GND 9 LVDS_D2+ 10 LVDS_D2-11 GND 12 GND 13 CLK+ 14 CLK- LVDS1 15 GND 16 GND 17 NC 18 NC 19 VDD 20 VDD EPI

57 Chapter 2 Installation LCD Backlight Control Connector Pin Signal Name 1 VCC_LCDBKLT 2 LCD_BKLTCTL LCDB1 3 LCD_BKLTEN (Pin Distance: 2.0mm) 4 GND Note: VCC_LCDBKLT---+12V backlight power (the current of the pin shall be limited below 1A); LCD_BKLTCTL---backlight control (This signal is output via Pineview D as PWM signal; voltage amplitude is between 0V ~ 3.3V while the duty cycle is between 0 ~ 100%); LCD_BKLTEN ----backlight enabling, active high. Audio Connector Provide one 2 5Pin audio connector (Pin Distance: 2.54mm); the pin definitions are as follows: Pin Signal Name Pin Signal Name 1 LOUT_R 2 LOUT_L 3 GND_AUDIO 4 GND_AUDIO 5 LIN_R 6 LIN_L AUDIO1 7 GND_AUDIO 8 GND_AUDIO 9 MIC_L 10 MIC_R SATA Connector Provide three SATA sockets; the pin definitions are as follows: Pin Signal Name 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ SATA1 ~ SATA3 7 GND EPI-1813

58 Chapter 2 Installation Hot-swap of SATA Hard Disk Notices for hot-swap of SATA hard disk: 1. The hard disk shall support SATA 2.0 and use 15-pin SATA hard disk power connector. 2. The driver of chipset shall support the hot-swap of SATA hard disk. 3. Hot-swap of SATA hard disk with the operating system is forbidden when system is power-on. SATA Data Cable SATA Power Cable Please carry out hot plug as follows, improper operation may destroy the hard disk or result in data lost. Hot Plug Step 1: Please plug the 1 x 4 pin SATA power connector (white) into the power adapter. Step 2: Please connect the SATA data cable to the SATA connector on board. EPI

59 Chapter 2 Installation Step 3: Please connect the 15-pin SATA power connector (black) to the SATA hard disk. Step 4: Please connect the SATA data cable to the SATA hard disk. Hot Unplug Step 1: Uninstall the hard disk from the device manager. Step 2: Unplug the data cable from the SATA hard disk. Step 3: Unplug the SATA 15-pin power connector (black) from the SATA hard disk EPI-1813

60 Chapter 2 Installation 2-in-1 Mouse and Keyboard Connector The board provides one 2-in-1 mouse and keyboard socket. KM1 Pin Signal Name 1 KB_DATA 2 MS_DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK Parallel Port The board provides one 2 13Pin parallel port (Pin Distance: 2.0mm). LPT1 Pin Signal Name Pin Signal Name 1 STB# 2 AFD# 3 PD0 4 ERR# 5 PD1 6 INIT# 7 PD2 8 SLIN# 9 PD3 10 GND 11 PD4 12 GND 13 PD5 14 GND 15 PD6 16 GND 17 PD7 18 GND 19 ACK# 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 NC EPI

61 Chapter 2 Installation USB Port The board provides four sets of 2 5Pin USB ports (Pin Distance: 2.54mm), which can connect with eight standard USB devices. The pin definitions are as follows: Pin Signal Name Pin Signal Name 1 +5V 2 +5V 3 USB1_Data- 4 USB2_Data- 5 USB1_Data+ 6 USB2_Data+ USB1 ~ USB4 7 GND 8 GND 9 NA 10 GND LAN Port The board provides two 10/100/1000Mbps LAN ports (LAN1 and LAN2), among which LAN1 supports Wake-on-LAN function. ACTLED and LILED are the green and dual color LEDs beside the Ethernet port, which respectively indicates the activity status and speed of LAN. Please refer to the status description for each LED: LAN1/LAN2 ACTLED (Green) LAN Activity Indicator LILED (Dual Color: O/G) Green LAN Speed Indicator 1000Mbps Blink Data Transmitting Orange 100Mbps Off No Data to Transmit Off 10Mbps EPI-1813

62 Chapter 2 Installation Status Indicator and Control Connector ATX Power Switch and HDD Indicator Connector (Pin Distance: 2.54mm) Pin Signal Name Pin Signal Name 1 PWRBTN# 2 GND FP1 3 GND 4 RESET# 5 HDD_LED- 6 HDD_LED+ Power Indicator Connector (Pin Distance: 2.54mm) Pin Signal Name 1 PWR_LED+ FP2 2 NC 3 GND Loudspeaker Output Connector (Pin Distance: 2.54mm) Pin Signal Name 1 SPEAKER 2 NC FP3 3 GND 4 +5V EPI

63 Chapter 2 Installation CF Socket The board provides one standard CF card socket (CF1). Pin Signal Name Pin Signal Name 1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS0# 32 CS1# 8 GND 33 VS1# 9 ATASEL# 34 IOR# 10 GND 35 IOW# 11 GND 36 WE# 12 GND 37 IRQ 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 VS2# 16 GND 41 RESET# 17 GND 42 IORDY 18 A2 43 DREQ 19 A1 44 DACK# 20 A0 45 DASP# 21 D0 46 ATA66_DET 22 D1 47 D8 23 D2 48 D9 24 WP/IOCS16# 49 D10 25 CD2# 50 GND EPI-1813

64 Chapter 3 BIOS Setup Chapter 3 BIOS Setup BIOS Overview BIOS (Basic Input and Output System) is solidified in the flash memory on the CPU board. Its main functions include: initialize system hardware, set the operating status of the system components, adjust the operating parameters of the system components, diagnose the functions of the system components and report failures, provide hardware operating and controlling interface for the upper level software system, guide operating system and so on. BIOS provides users with a human-computer interface in menu style to facilitate the configuration of system parameters for users, control power management mode and adjust the resource distribution of system device, etc. Setting the parameters of the BIOS correctly could enable the system operating stably and reliably; it could also improve the overall performance of the system at the same time. Inadequate even incorrect BIOS parameter setting will decrease the system operating capability and make the system operating unstably even unable to operate normally. BIOS Parameter Setup Prompt message for BIOS setting may appear once powering on the system. At that time (inefficient at other time), press the key specified in the prompt message (usually <Del>) to enter BIOS setting. When the BIOS setting in CMOS is destroyed, system may also require entering BIOS setting or selecting certain default value. All the setup values modified by BIOS are saved in the CMOS storage in system. The CMOS storage is powered by battery; unless clearing CMOS contents, or else its contents will not be lost even if powered off. Note! BIOS setting will influent the computer performance directly. Setting parameter improperly will cause damage to the computer; it may even unable to power on. Please use the internal default value of BIOS to restore the system. Our company is constantly researching and updating BIOS, its setup interface may be a bit different. The figure below is for reference only; it may be different from your BIOS setting in use. EPI

65 Chapter 3 BIOS Setup Basic Function Setting for BIOS After starting SETUP program, the main interface of CMOS Setup Utility will appear: BIOS SETUP UTILITY System Overview Processor Type : Intel(R) Atom(TM) CPU D510 Speed :1666MHz Cores :2 System Memory Size 1.66GHz Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit System Time [00:47:55] System Date [Mon 01/11/2010] V02.57 (c)copyright ,American Megatrends, Inc. Main System Time Choose this option and set the current time by < + > / < - >, which is displayed in format of hour/minute/second. Reasonable range for each option is: Hour (00-23), Minute (00-59), Second (00-59). System Date Choose this option and set the current date by < + > / < - >, which is displayed in format of month/date/year. Reasonable range for each option is: Month (Jan.-Dec.), Date (01-31), Year (Maximum to 2099), Week (Mon. ~ Sun.) EPI-1813

66 Chapter 3 BIOS Setup Advanced Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction BIOS SETUP UTILITY Configure CPU CPU Configuration IDE Configuration Super I/O Configuration ISA I/O Decode Configuration ISA Memory Decode Configuration Hardware Health Configuration USB Configuration Power Management Configuration Clock Generator Configuration Select Screen Select Item Enter Go to Sub Screen Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. CPU Configuration BIOS SETUP UTILITY Configure advanced CPU settings Brand String: Intel(R) Atom(TM) CPU 1.66GHz Frequency; :1.66GHz FSB Speed; :667MHz Cache L1; :48 KB Cache L2; :1024 KB Ratio Actual Value :10 Hyper Threading Technology [Enabled] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc Hyper Threading Technology Control switch for Intel Hyper Threading Technology function. EPI

67 Chapter 3 BIOS Setup IDE Configuration BIOS SETUP UTILITY IDE Configuration ATA/IDE Configuration Configure SATA as Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Third IDE Slave [Enhanced] [IDE] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. ATA/IDE Configuration This option is used to configure the operating mode of ATA; there are two options for this item: Compatible and Enhanced. Configure SATA as SATA controller type selection, it is corresponding with the options of IDE and AHCI. Only when ATA/IDE Configuration is under Enhanced mode, is AHCI supported. AHCI function requires supports from hardware chip and OS. Legacy IDE Channels Configure the IDE channel type under Compatible mode; it is corresponding with the options of SATA Only, SATA Pri, PATA Sec and PATA Only. Primary ~ Third IDE Master/Slave * Type Not Installed: IDE device cannot be detected by system; EPI-1813

68 Chapter 3 BIOS Setup AUTO: automatic detection of IDE parameters when power on; CD/DVD: used for ATAPI CDROM; ARMD: used for various analog IDE devices. * LBA/Large Mode Used to set whether to support LBA mode or not. * Block(Multi-sector Transfer) Used to set whether to support multi-sector simultaneous transfer or not. * PIO Mode Used for PIO mode setting. * DMA Mode Used for DMA mode setting. * S.M.A.R.T Used to set whether to enable S.M.A.R.T function and it is only effective for the hard disk supporting this function. * 32Bit Data Transfer This option is used to enable 32-bit hard disk accessing mode, which could optimize hard disk read and write speed. AHCI Port 0 ~2 Configuration menu for AHCI port, it is displayed only when the SATA controller is configured to AHCI or RAID. * SATA Port0 ~ 2 Auto: automatic detection of SATA devices when power on; Not Installed: disable the port and detection. * S.M.A.R.T Used to set whether to enable S.M.A.R.T function and it is only effective for the hard disk supporting this function. EPI

69 Chapter 3 BIOS Setup Super I/O Configuration Configure Super I/O Chipset Floppy A OnBoard Floppy Controller Serial Port1 Address Serial Port2 Address BIOS SETUP UTILITY [Disabled] [Enabled] Parallel Port Address [378] Parallel Port Mode Parallel Port IRQ [3F8/IRQ4] [2F8/IRQ3] [Normal] [IRQ7] Allows BIOS to Enable or Disable Floppy Controller. Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Floppy A Configure the floppy driver type. OnBoard Floppy Controller Used to enable floppy driver controller. Serial Port 1 Address (Default value is 3F8H/IRQ4), set the address and IRQ of COM1 on motherboard. The options are: Disabled, 3F8H/IRQ4, 3E8/IRQ4, 2E8/IRQ3 and 2F8H/IRQ3. Serial Port 2 Address (Default value is 2F8H/IRQ3), set the address and IRQ of COM2 on motherboard. The options are: Disabled, 3F8H/IRQ4, 3E8/IRQ4, 2E8/IRQ3 and 2F8H/IRQ3. Parallel Port Address Set the address of the parallel port on motherboard and the default value is 378. Parallel Port Mode Set the parallel port mode on motherboard. Parallel Port IRQ Set the IRQ of the parallel port on motherboard EPI-1813

70 Chapter 3 BIOS Setup ISA I/O Decode Configuration BIOS SETUP UTILITY Configure ISA I/O Address Decode I/O Space 0 Decode I/O Base 0 Decode I/O Size 0 Decode I/O Space 1 Decode I/O Base 1 Decode I/O Size 1 Decode I/O Space 2 Decode I/O Base 2 Decode I/O Size 2 Decode I/O Space 3 Decode I/O Base 3 Decode I/O Size 3 Decode I/O Space 4 Decode I/O Base 4 Decode I/O Size 4 Decode I/O Space 5 Decode I/O Base 5 Decode I/O Size 5 [Enabled] [0100h] [64 Bytes] [Enabled] [0140h] [32 Bytes] [Enabled] [0200h] [128 Bytes] [Enabled] [0300h] [64 Bytes] [Enabled] [0340h] [32 Bytes] [Enabled] [0A70h] [16 Bytes] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. Decode I/O Space(0-5) Decode IO space switch (n). Decode I/O Base(0-5) Decode IO space base address. Decode I/O Size(0-5) Decode IO space size. EPI

71 Chapter 3 BIOS Setup ISA Memory Decode Configuration Configure ISA Memory Address Memory Space 0 Memory Space 1 Memory Space 2 Memory Space 3 BIOS SETUP UTILITY [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. Memory Space(0-3) Decode Memory space switch. Decode MEM Base(0-3) Decode Memory space base address. Decode Size(0-3) Decode Memory space size. Hardware Health Configuration BIOS SETUP UTILITY Hardware Health Configuration System Temperature : 30 /86 CPU Temperature : 37 /98 Vcore : V V3.3 : V V5.0 : V V12.0 : V VBAT : V Enables Hardware Health Monitoring Device Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc EPI-1813

72 Chapter 3 BIOS Setup System Temperature Current system temperature, it is monitored by thermal resistor on motherboard. CPU Temperature Current CPU temperature, it is monitored by temperature sensors on motherboard. Vcore CPU core voltage; V3.3/ V5.0/ V12.0 Turn on/off power to output voltage. VBAT Monitor the voltage of the battery. USB Configuration USB Configuration USB Devices Enabled : 1 Keyboard, 1 Drive USB Function [8 USB Ports] USB 2.0 Controller [Enabled] Legacy USB Support [Auto] USB Mass Storage Device Configuration USB Function BIOS SETUP UTILITY Enables USB host controllers. Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. This option sets the amount of USB controller; that is to confirm how many USB controllers it supports. One controller usually supports two USB ports. USB 2.0 Controller This option is used to select whether to support USB 2.0 controller. Legacy USB Support EPI

73 Chapter 3 BIOS Setup This option is used to support legacy USB devices (keyboard, mouse and storage device); when this option is set to Enabled, the USB device could be used even if under OS that doesn t support USB, such as DOS. USB Mass Storage Device Configuration This option is used to configure the USB mass storage device, including Reset delay setting and enumeration type. Power Management Configuration BIOS SETUP UTILITY Power Management Configuration ACPI APIC Support [Enabled] Select Screen Restore on AC Power Loss [Last state] Select Item Resume on RTC Alarm [Disabled] + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. ACPI APIC Support This option is used to enable or disable APIC under ACPI OS. Restore on AC Power Loss This option could set the system status when the computer is re-electrified after powered off under AC. Power Off is to make the system at power off status; Power On is to make the system power on automatically; Last State is to recover the status before powering off. Resume on RTC Alarm This option is used to enable or disable the system clock. When the specified time is expired, it will wake the system from power saving mode, even from power off mode. This function shall be supported by ATX power EPI-1813

74 Chapter 3 BIOS Setup Clock Generator Configuration Configure Clock Generator Spread Spectrum Auto PCI Clock BIOS SETUP UTILITY [Enabled] [Enabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Spread Spectrum This option is used to control the spread spectrum of clock signal. Auto PCI Clock This option is used to realize the automatic detection of the device on PCI slot; if there is no device on the slot, it will disable the relevant clock signal on that slot. Chipset BIOS SETUP UTILITY Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction. North Bridge Chipset Configuration DRAM Frequency [Auto] Configure DRAM Timing by SPD [Enabled] Initiate Graphic Adapter [PCI/IGD] Boot Display Device [CRT+LVDS] Flat Panel Type [800x600/S/18/G104S] UserDefine Panel Type [Disabled] Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit South Bridge Chipset Configuration Onboard Audio Controller [Enabled] V02.57 (c)copyright , American Megatrends, Inc. EPI