DF404G2-E-PARTS CATLOG.pdf - PDF Free Download

目录 CONTENT 1 空滤器总成 Air filter... 1 2 散热器总成 Radiator... 3 3 油门操纵机构总成 Throttle Control Mechanism... 5 4 离合器总成 Clutch... 7 5 排气管总成 Exhaust Pipe... 11 6 机架总成 Frame... 13 7.1 前驱动桥总成 ( 中 ) Front Driving Axle (Middle)... 15 7.2 前驱动桥总成 ( 左边减速 ) Front Wheel Drive Axle (Left Side Slowdown)... 18 7.3 前驱动桥总成 ( 右边减速 ) Front Wheel Drive Axle (Right side Slowdown)... 22 7.4 前驱动桥总成 (304.31.022 1 部件 ) Front Wheel Drive Axle (304.31.022 1 Assembly)... 26 7. 5 前驱动桥总成 (304.31.014A 部件 ) Front Wheel Drive Axle (304.31.014A Assembly)... 28 8 前驱动轮总成 Front Drive Wheel... 30 9 驱动轮总成 Drive Wheel... 32 10.A 摆杆式牵引装置总成 Tractor Drawbar... 34 10.B 牵引装置总成 ( 旋转式 ) Clevis type... 36 11 传动轴总成 Transmission Shaft... 38 12.1 变速箱总成 (A) Gearbox(A)... 41 I

12.2 变速箱总成 (B) Gearbox(B)... 45 12.3 行星机构总成 Planet Mechanism System... 50 13.1 后桥总成 (A) Rear Axle(A)... 52 13.2 后桥总成 (B) Rear Axle(B)... 54 13.3 操纵机构总成 Operation Mechanism System... 56 13.4 差速锁总成 Differential Lock... 59 14 最终传动总成 Final Transmission... 62 15.1 液压转向系统总成 Full Hydraulic Power Steering Gear... 64 15.2 转向总成 Steering System... 68 16 动力输出总成 PTO... 70 17 分动箱总成 Transfer Case... 74 18 制动器及操纵机构总成 Brake Operation Mechanism... 78 19 座椅总成 Seat... 83 20.1 安全架总成 Safety Frame... 85 20.2 前安全架总成 Front Safety Frame... 87 21.1 机罩仪表罩总成 (A) Hood and Panel (A)... 89 21.2 机罩仪表罩总成 (B) Hood and Panel (B)... 92 22 电气系统总成 Electrical System... 95 23 工具箱总成 Toolbox... 98 24 油箱总成 Fuel Tank... 100 II

25 地板挡泥板总成 Foot Mud Shields Rest... 102 26.1 提升器操纵机构总成 Hydraulic Power Lift Operation Mechanism System... 106 26.2 分配器总成 Hydraulic Oil Distributor... 108 26.3 提升器总成 Hydraulic Power Lift... 111 27 悬挂装置总成 Suspension Mechanism... 115 28.1 液压提升管路系统总成 ( 配多路阀 ) Hydraulic Lifting Pipeline Assembly... 118 28.2 多路阀操纵组合件 Multiple Directional Control Valve Operation Mechanism... 121 29 前配重总成 Front Balance Weight... 123 30 遮阳篷总成 Sunshade(Optional)... 125 ENGINE 31 气缸盖罩总成 Cylinder Head Cover Assembly(Fig.1)... 127 32 气缸盖总成 Cylinder Head Assembly(Fig.2)... 129 33 机体齿轮室总成 Cylinder Block and Gear Case Assembly(Fig.3)... 132 34 正时齿轮系总成 Timing Gear Train(Fig.4)... 136 35 活塞连杆总成 Piston and Connecting Rod Assembly(Fig.5)... 138 36 曲轴飞轮总成 Crankshaft and Flywheel Assembly(Fig.6)... 140 37 配气机构 Valve Timing Mechanism(Fig.7)... 142 38 水泵风扇总成 Water Pump and Fan Assembly(Fig.8)... 145 39 油底壳总成 Oil Sump Assembly (Fig.9)... 148 40 机油泵总成 Lubricating Oil Pump Assembly (Fig.10)... 150 III

41 燃油系统总成 Fuel System (Fig.11)... 152 42 机油集滤器总成 Oil Suction Strainer Assembly (Fig.12)... 154 43 张紧轮部件 Tension pulley assembly (Fig.13)... 156 44 机滤发电机起动电机 Oil Filter/Air Filter/Generator/Starting Motor/Silencer(Fig.14)... 158 IV

1 空滤器总成 Air Filter 1 空气滤清器壳体 Air filter rind 1 2 GB/T6170-2000-M10 螺母 M10 Hex.nut M10 2 3 GB/T93-1987-10 垫圈 10 Spring Lock washer10 2 4 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 5 GB/T5783-2000-M10 25 螺栓 M10 25 Hex.head bolt M10 25 2 7 JB/T8870-1999-(44-64) 喉箍 (44-64) Clip(44-64) 1 6 404G2-6E.10.102 进气管 Air pipe 1 8 JB/T8870-1999-(64-76) 喉箍 (64-76) Clip (64-76) 1 9 KW1025 滤芯 filter screen 1 10 404G2-6E.10.101 空气滤清器 Air filter 1 2

2 散热器总成 Radiator 1 550-1.51.101 密封条 Airproof piece 按需 Optional 2 GB/T5783-2000-M8 20 螺栓 M8 20 Hex.head bolt M8 20 1 3 GB/T97.1-2002-8 垫圈 8 Plain washer 8 1 4 GB/T93-1987-8 垫圈 8 Spring lock washer 8 1 5 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 1 6 404G2.13.101 水箱撑杆 Supporting rod, radiator 1 7 404G2-6E.13.104 水箱右隔风板 Right shield board,radiator 1 Optional 8 304G2-6E.13.101 上输水管 Upper water hose 1 9 JB/T8870-1999-2A(35-51) 喉箍 2A(35-51) Hose clamp 2A (35-51) 4 10 404G2-6E.13.011 散热器部件 Radiator 1 11 404G2-6E.13.102 下输水管 Lower water pipe hose 1 12 GB/T97.1-2002-12 垫圈 12 Plain washer 12 2 13 GB/T93-1987-12 垫圈 12 Spring lock washer 12 2 14 GB/T6170-2000-M12 螺母 M12 Hex. nut M12 2 15 404G2-6E.13.103 水箱左隔风板 Left shield board,radiator 1 Optional 16 304G2-6E.13.103 橡胶板 rubber pad 1 17 GB/T6170-2000-M6 螺母 M6 Hex. nut M6 8 18 GB/T93-1987-6 垫圈 6 Spring lock washer 6 8 19 304G2-6E.13.105 弹簧片 Spring piece 4 20 304G2-6E.13.108 水箱下挡风板 Down shield board,radiator 1 21 GB/T96.1-2002-M6 垫圈 M6 Plain washer 6 8 22 GB/T5783-2000-M6 16 螺栓 M6 16 Hex.head bolt M6 16 8 4

3 油门操纵总成 Throffle Control Mechanism 1 404G2-6F.20.014 手油门拉线组合件 Hand throttle wire 1 2 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. head bolt M8 25 1 3 GB/T97.1-2002-8 垫圈 8 Plain washer 8 2 4 504G3.20.104 垫套 Bush 1 5 504G3.20.021 连接板焊合件 Connect board 1 6 504G3.20.115 转套 Thimble 1 7 GB/T91-2000-2 14 销 2 14 Split pin 2 14 1 8 504G3.20.102 摩擦片 Friction lining 1 9 504G3.20.105 碟形垫片 Acetabuliform mat 2 10 GB/T6170-2000-M12 螺母 M12 Hex. nut M12 2 11 504G3.20.101 橡胶套 Rubber boot 1 12 504G3.20.012 手油门操纵杆焊合件 Operating lever,hand throttle 1 13 504G3.20.011 手柄组合件 Handle 1 14 GB/T 845-1985-ST4.2 13 自攻螺钉 ST4.2 13 Bolt ST4.2 13 1 15 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 2 16 GB/T5783-2000-M10 45 螺栓 M10 45 Hex. head bolt M10 45 1 17 504G3.21.103 橡胶垫 Rubber blanket 2 18 GB/T5782-2000-M10 65 螺栓 M10 65 Hex. head bolt M10 65 1 19 GB/T894.1-1986-15 挡圈 15 Circlip for shaft 15 2 20 254G3.40.134 衬套 Bushing 1 21 504G3-3.20.101-1 回位弹簧 Return spring 1 22 504G3-E.20.011-1 脚油门踏板焊合件 Foot throttle lever 1 23 GB/T91-2000-1.6 12 销 1.6 12 Split pin 1.6 12 5 24 GB/T97.1-2002-6 垫圈 6 Plain washer 6 4 25 GB/T882-1986-B6 20 销轴 B6 20 Clevis pin with head B6 20 1 26 404G2-E.20.015 脚油门拉线组合件 Foot throttle wire 1 6

4 离合器总成 Clutch 1 400-6.21.013 主离合器从动盘总成 Driven plate,main clutch 1 无石棉 2 300.21C.103-1 主离合器压盘 Pressure plate,main clutch 1 3 304G2-6.21.101 碟形弹簧 Disc spring 2 4 300.21C.104 离合器固定压盘 Fixed pressure plate, clutch 1 5 400-6.21.012 PTO 离合器从动盘总成 Driven plate PTO clutch 1 无石棉 6 300.21C.106-1 PTO 离合器压盘 Pressure plate PTO clutch 1 7 300.21C.113-1 调整螺栓 Adjusting bolt 3 8 GB/T6171-2000-M10 1 螺母 M10 1 Fine thread hex. nut M10 1 3 9 300.21C.107-1 离合器盖 Clutch cover 1 10 GB/T93-1987-10 垫圈 10 Spring lock washer 10 10 11 GB/T5782-2000-M10 90 螺栓 M10 90 Hex. head bolt M10 90 6 12 300.21.158 销轴 Clevis pin with head 3 13 GB/T93-1987-12 垫圈 12 Spring lock washer 12 12 14 GB/T5783-2000-M12 45 螺栓 M12 45 Hex. head bolt M12 45 12 15 GB/T119.1-2000-D14 26 销 D14 26 Parallel pin D14 26 2 300.37.154 16 404G2-6F.21.105 盖板 Cover 1 17 254G3.21.111 分离轴衬套 Release shaft bush 2 18 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 4 19 404G2-6F.21.104 纸垫 Paper gasket 1 20 GB/T119.1-2000-B10 22 销 B10 22 Parallel pin B10 22 2 21 404G2-6F.21.101 离合器壳体 Clutch case 1 22 504G3.43.135 衬套 (2520) Bush(2520) 2 23 504G3.43.101 缓冲垫 Rubber plug 1 24 404G2-6F.21.021 离合器踏杆焊合件 Clutch pedal 1 25 GB/T91-2000-3.2 25 销 3.2 25 Split pin 3.2 25 2 8

4 离合器总成 Clutch 续表 26 GB/T97.1-2002-10 垫圈 10 Plain washer 10 5 27 GB/T882-2000-B10 22 销 B10 22 Parallel pin B10 22 2 28 504G3.43.103-1 回位弹簧 Return spring 1 29 404G2-6F.21.107 离合器拉杆 Release pull-rod 1 30 300.37.131-1 盖板 Inspection opening cover 1 31 GB/T93-1987-6 垫圈 6 Spring lock washer 6 4 32 GB/T5783-2000-M6 12 螺栓 M6 12 Hex. head bolt M6 12 4 33 504G3.21.103 橡胶垫 Rubber plug 1 34 GB/T5783-2000-M10 45 螺栓 M10 45 Hex. head bolt M10 45 1 35 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 1 36 404G2-6F.21.153 分离轴衬套 Release shaft bush 2 37 300.37.180 螺孔封套 Protecting plug,thread hole 1 38 300.21A.148 拉杆叉头 Rod clevis 1 39 GB/T894.1-1986-22 挡圈 22 Circlip for shaft 22 1 40 GB/T6170-2000-M6 螺母 M6 Hex. nut M6 1 41 300.21C.133 调整螺栓 Adjusting bolt 1 42 404G2-6F.21.108 安全开关支架 Safety switch support 1 43 404G2-6F.21.012 分离轴焊合件 Release shaft,clutch 1 44 404G2-6F.21.102 离合器拨叉 Release fork 1 45 GB/T879-2000-8 35 销 8 35 Slotted spring pin 8 35 2 46 GB/T879-2000-5 35 销 5 35 Slotted spring pin 5 35 2 47 GB/T894.1-1986-24 挡圈 24 Circlip for shaft 24 1 48 404G2-6F.21.103 分离轴承座 Release bearing seat 1 49 GB/T6173-2000-M10 1 螺母 M10 1 Fine thread hex. nut M10 1 6 9

4 离合器总成 Clutch 续表 50 65TNK20 分离轴承 Release bearing 1 51 404G2-6F.21.116 主分离杠杆 Main release lever 3 52 300.21C.115 回位弹簧 Return spring 3 53 300.21C.114-1 调整螺栓 Adjusting bolt 3 54 GB/T6171-2000-M10 1-L 螺母 M10 1- 左 Fine thread hex. nut M10 1-L 1 55 254G2.21.106 连接叉 Rod clevis 1 10

5 排气管总成 Exhaust pipe 1 304G2-6E.22.011 消声器合件 Dissipative muffler 1 2 304G2-6E.22.101 抱箍 Clip 1 3 GB/T6170-2000-M8 螺母 M8 Hex.nut M8 1 4 404G2-6E.22.012 排气弯管焊合件 Exhaust pipe 1 5 GB/T5783-2000-M8 25 螺栓 M8 25 Hex.head bolt M8 25 5 6 GB/T93-1987-8 垫圈 8 Spring Lock washer 8 5 7 GB/T97.1-2002-8 垫圈 8 Plain washer 8 5 8 304G2-6E.22.102 排气管纸垫 Paper gasket 1 9 404G2-6E.22.103-1 排气弯管护罩 Exhaust pipe cover 1 10 GB/T97.1-2002-6 垫圈 6 Plain washer 6 2 11 GB/T93-1987-6 垫圈 6 Spring Lock washer 6 2 12 GB/T5783-2000-M6 12 螺栓 M6 12 Hex.head bolt M6 12 2 12

6 机架总成 Frame 1 404G2-6E.30.011 机架焊合件 Frame 1 2 GB/T93-1987-14 垫圈 14 Spring Lock washer14 16 3 GB/T5783-2000-M14 35 螺栓 M14 35 Hex.head bolt M14 35 16 8.8 级 4 GB/T5783-2000-M16 45 螺栓 M16 45 Hex.head bolt M16 45 4 5 GB/T93-1987-16 垫圈 16 Spring Lock washer16 4 6 GB/T6170-2000-M16 螺母 M16 Hex.nut M16 4 7 GB/T6170-2000-M16 螺母 M10 Hex.nut M10 4 8 300.47.143 电瓶胶垫 rubber gasket 1 9 304G2-6.30.110 U 型螺栓 U model of bolt 1 10 GB/T5783-2000-M8 16 螺栓 M8 16 Hex.head bolt M8 16 2 Optional 11 GB/T93-1987-8 垫圈 8 Spring Lock washer8 2 Optional 12 250.30.116 手摇起动支承板 Starting crank gate 1 Optional 13 304G2-6.30.013 电瓶架焊合件 Battery bracket 1 14 GB/T5783-2000-M10 20 螺栓 M10 20 Hex.head bolt M10 20 4 15 GB/T93-1987-10 垫圈 10 Spring Lock washer10 4 16 304G2-6.30.012-1 配重架焊合件 Assistant weight support 1 17 250.30.103 蓄电池防护板 Rubber gasket for battery 1 14

7.1 前驱动桥总成 ( 中 ) Front Wheel Drive Axle (Middle) 1 GB/T5783-2000-M6 12 螺栓 M6 12 Hex. head bolt M6 12 4 2 GB/T93-1987-6 垫圈 6 Spring lock washer 6 4 3 JB/T7940.1-1995-M10 1 油杯 M10 1 Grease cup M10 1 2 4 304.31.019 前支座端盖组合件 End cover of front pedestal 1 5 304.31.122 端盖垫片 End cover gasket 1 6 GB/T6170-2000-M16 螺母 M16 Hex. nut M16 4 7 GB/T93-1987-16 垫圈 16 Spring lock washer 16 4 8 304.31.220-2 前支座 Front pedestal 1 9 GB/T27-1988-M16 65 螺栓 M16 65 Hex. head bolt M16 65 4 10 304.31.219-1 前支座衬套 Front pedestal bush 1 11 304.31.123-1 前摆轴垫片 Shims for front swing axle one set One pcs for each size 12 GB/T3452.1-1992-65 2.65 O 形圈 65 2.65 O-ring seal 65 2.65 1 13 ZB T32003-88-24 碗形塞片 24 Casing cap 1 14 GB/T5786-2000-M12 1.5 35 螺栓 M12 1.5 35 Hex. head bolt M12 1.5 35 8 15 GB/T93-1987-12 垫圈 12 Spring lock washer 12 24 16 304.31.124-2 前摆轴 Front swing axle 1 17 GB/T3452.1-1992-69 3.55 O 形圈 69 3.55 O-ring seal 69 3.55 1 18 304.31.116-2 主传动壳体 Main drive case 1 19 200.38.024 放油螺塞总成 Oil drain plug 1 20 JB-FT-CU-16 组合铜垫圈 16 Copper washer 16 3 21 304.31.125-1 轴承座垫片 Shims for bearing seat one set Two pcs for each size 22 304.31.022-1 主动锥齿轮总成 Bevel drive pinion assembly 1 23 304.31.222-3 后支座 Rear pedestal 1 24 304.31.221-1 后支座衬套 Rear pedestal bush 1 25 GB/T3452.1-1992- 69 2.65 O 形圈 69 2.65 O-ring seal 69 2.65 1 16

7.1 前驱动桥总成 ( 中 ) Front Wheel Drive Axle (Middle) 续表 26 304.31.126-1 后支座盖垫片 Gasket for end cover 1 27 304.31.127-2 后支座盖 End cover of rear pedestal 1 28 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 29 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. Head bolt M8 25 4 30 GB/T3452.1-1992-48.7 3.55 O 形圈 48.7 3.55 O-ring seal 48.7 3.55 1 31 304.31.128-1 立轴套管垫片 Gasket for Upright shaft housing 2 32 GB/T5783-2000-M10 35 螺栓 M10 35 Hex. head bolt M10 35 20 33 GB/T93-1987-10 垫圈 10 Spring lock washer 10 20 34 304.31.013-1 量油尺合件 Oil dipstick 1 35 GB/T5783-2000-M12 35 螺栓 M12 35 Hex. head bolt M12 35 16 36 304.31.233-1 左半轴套管 Left half shaft housing 1 37 304.31.234 转向油缸座 Power steering cylinder bracket 1 38 GB/T119.1-2000-A10 16 销 A10 16 Straight pin A10 16 2 39 GB/T3452.1-1992-160 3.55 O 形圈 160 3.55 O-ring seal 160 3.55 2 40 304.31.117-1 主传动壳体垫片 Shims for main drive case two set Two pcs for each size 41 304.31.014A 差速器总成 Differential assembly 1 42 GB/T119.1-2000-A10 20 销 A10 20 Straight pin A10 20 2 43 304.31.115-1 右半轴套管 Right half shaft housing 1 44 304.31.118-1 通气螺塞 Vent plug 1 45 304.31.119-1 通气管 Vent pipe 1 304.31.119A 通气管 Vent pipe 1 for paddy field 17

7.2 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 1 GB/T6176-2000-M18 1.5 螺母 M18 1.5 Hex. nut M18 1.5 2 2 GB/T93-1987-18 垫圈 18 Spring lock washer 18 6 3 304.31.179 螺柱 Double screw bolt 2 M18 1.5 52-20 4 GB/T5786-2000-M18 1.5 35 螺栓 M18 1.5 35 hex. head bolt M18 1.5 35 4 level 8.8 5 304.31.101-3 驱动轴 Drive shaft 1 6 404-9.31.111 防泥水油封 MC50 72 15 Oil-seal MC50 72 15 2 7 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 16 8 GB/T93-1987-10 垫圈 10 Spring lock washer 10 26 9 304.31.104-3 驱动轴盖 Drive shaft cover 1 10 GB/T276-1994-6209 轴承 6209 Ball bearing 6209 1 11 304.31.102-2 驱动轴固定圈 Fixing ring of drive shaft 2 12 304.31.103-2 驱动轴垫圈 Drive shaft sleeve 1 13 304.31.132-3 末减速被动齿轮 Driven bevel gear of final drive 1 14 GB/T276-1994 轴承 6207 Ball bearing 6207 1 15 304.31.105-1 驱动轴盖垫片 Gasket for drive shaft cover 1 16 304.31.228-5 左边减速壳体 Left final drive housing 1 17 GB/T119.2-2000-A10 24 销 A10 24 Straight pin A10 24 2 18 GB/T276-1994-61910 轴承 61910 Ball bearing 61910 1 19 GB/T297-1994-32909 轴承 32909 Tapered roller bearing 32909 1 20 304.31.131-3 末减速主动齿轮 Driving bevel gear of final drive 1 21 304.31.107-4 立轴 Upright shaft 1 22 GB/T276-1994 轴承 6208 Ball bearing 6208 2 23 850-2.39.112/113/114 调整垫片 Adjusting shims Needed 24 GB/T3452.1-1992-75 2.65 O 形圈 75 2.65 O-ring seal 75 2.65 1 25 304.31.137-3 下轴承盖 Lower bearing cover 1 19

7.2 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 续表 26 JB-FT-CU-16 组合铜垫圈 16 Combined seal washer 16 1 27 200.38.024 放油螺塞总成 Oil drain plug 1 28 JB/T7940.1-1995-M8 1 油杯 M8 1 Grease cup M8 1 1 29 304.31.201-4 左转向臂 Left steering arm 1 30 304.31.202-1 联接转向臂衬套 Steering arm bushing 1 31 GB/T5783-2000-M12 40 螺栓 M12 40 Hex. head bolt M12 40 4 32 GB/T93-1987-12 垫圈 12 Spring lock washer 12 4 33 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 11 34 304.31.249/250/251/252 转向臂调整垫片 Steering arm adusting shim Needed 35 GB/T3452.1-1992-34.5 2.65 O 形圈 34.5 2.65 O-ring seal 34.5 2.65 1 36 304.31.111-4 上轴承盖 Upper bearing cover 1 37 GB/T3452.1-1992-85 2.65 O 形圈 85 2.65 O-ring seal 85 2.65 1 38 304.31.133 中间传动调整垫片 Adjusting shims for the first drive One set Two pcs for each size 39 GB/T276-1994-6011 轴承 6011 Ball bearing 6011 1 40 304.31.138 锁紧垫片 Lock washer 1 41 304.31.110-1 立轴挡圈 Blocking ring of upright shaft 1 42 304.31.112-2 调整垫片 Adjusting shims One set Two pcs for each size 43 304.31.113-1 中间传动被动齿轮 Driven bevel gear of the first drive 1 44 304.31.108-4 立轴套管 Upright shaft housing 1 45 GB/T119.2-2000-A10 20 销 A10 20 Straight pin A10 20 1 46 304.31.129-1 中间传动主动齿轮 Driving bevel gear of the first drive 1 47 304.31.114-2 半轴 Half shaft 1 48 404B.31.110 左梯形臂 Left steering trapezoid arm 1 49 450.31.024-1 拉杆接头总成 ( 左 ) Linkage ball joint (Left) 1 20

7.2 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 续表 50 GB/T6173-2000-M18 1.5-Left 螺母 M18 1.5- 左 Hex.thin nut M18 1.5-Left 1 51 404B.31.105 横拉杆 Steering tie rod 1 52 GB/T6173-2000-M18 1.5 螺母 M18 1.5 Hex.thin nut M18 1.5 1 53 450.31.026-1 拉杆接头总成 ( 右 ) Linkage ball joint (Right) 1 54 GB/T6181-1986-M14 螺母 M14 Hex. thin slotted nut M14 2 55 GB/T91-2000-3.2 22 销 3.2 22 Split pin 3.2 22 2 56 GB/T308-2002-8.7312G200b 钢球 8.7312G200b Ball 8.7312G200b 1 11/32" 57 GB/T6171-2000-M10 1 螺母 M10 1 Hex. nut M10 1 1 58 504.31.144 紧定螺钉 Set screw 1 M10 1 62 左边减速总成 Left final drive housing assembly 1 21

7.3 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 1 GB/T6176-2000-M18 1.5 螺母 M18 1.5 Hex. nut M18 1.5 2 2 GB/T93-1987-18 垫圈 18 Spring lock washer 18 6 3 304.31.179 螺柱 Double screw bolt 2 M18 1.5 52-20 4 GB/T5786-2000-M18 1.5 35 螺栓 M18 1.5 35 hex. head bolt M18 1.5 35 4 level 8.8 5 304.31.101-3 驱动轴 Drive shaft 1 6 404-9.31.111 防泥水油封 MC50 72 15 Oil-seal MC50 72 15 2 7 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 16 8 GB/T93-1987-10 垫圈 10 Spring lock washer 10 26 9 304.31.104-3 驱动轴盖 Drive shaft cover 1 10 GB/T276-1994-6209 轴承 6209 Ball bearing 6209 1 11 304.31.102-2 驱动轴固定圈 Fixing ring of drive shaft 2 12 304.31.103-2 驱动轴垫圈 Drive shaft sleeve 1 13 304.31.132-3 末减速被动齿轮 Driven bevel gear of final drive 1 14 GB/T276-1994-6207 轴承 6207 Ball bearing 6207 1 15 304.31.105-1 驱动轴盖垫片 Gasket for drive shaft cover 1 16 304.31.216-5 右边减速壳体 Right final drive housing 1 17 GB/T119.2-2000-A10 24 销 A10 24 Straight pin A10 24 2 18 GB/T276-1994-61910 轴承 61910 Ball bearing 61910 1 19 GB/T297-1994-32909 轴承 32909 Tapered roller bearing 32909 1 20 304.31.131-3 末减速主动齿轮 Driving bevel gear of final drive 1 21 304.31.107-4 立轴 Upright shaft 1 22 GB/T276-1994-6208 轴承 6208 Ball bearing 6208 2 23 850-2.39.112/113/114 调整垫片 Adjusting shims Needed 24 GB/T3452.1-1992-75 2.65 O 形圈 75 2.65 O-ring seal 75 2.65 1 25 304.31.137-3 下轴承盖 Lower bearing cover 1 23

7.3 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 续表 26 JB-FT-CU-16 组合铜垫圈 16 Combined seal washer 16 1 27 200.38.024 放油螺塞总成 Oil drain plug 1 28 JB/T7940.1-1995-M8 1 油杯 M8 1 Grease cup M8 1 1 29 304.31.215-4 右联接臂 Right linking arm 1 30 304.31.202-1 联接转向臂衬套 Steering arm bushing 1 31 GB/T5783-2000-M12 40 螺栓 M12 40 Hex. head bolt M12 40 4 32 GB/T93-1987-12 垫圈 12 Spring lock washer 12 4 33 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 11 34 304.31.249/250/251/252 转向臂调整垫片 Steering arm adusting shim Needed 35 GB/T3452.1-1992-34.5 2.65 O 形圈 34.5 2.65 O-ring seal 34.5 2.65 1 36 304.31.111-4 上轴承盖 Upper bearing cover 1 37 GB/T3452.1-1992-85 2.65 O 形圈 85 2.65 O-ring seal 85 2.65 1 38 304.31.133 中间传动调整垫片 Adjusting shims for the first drive One set Two pcs for each size 39 GB/T276-1994-6011 轴承 6011 Ball bearing 6011 1 40 304.31.138 锁紧垫片 Lock washer 1 41 304.31.110-1 立轴挡圈 Blocking ring of upright shaft 1 42 304.31.112-2 调整垫片 Adjusting shims One set Two pcs for each size 43 304.31.113-1 中间传动被动齿轮 Driven bevel gear of the first drive 1 44 304.31.108-4 立轴套管 Upright shaft housing 1 45 GB/T119.2-2000-A10 20 销 A10 20 Straight pin A10 20 1 46 304.31.129-1 中间传动主动齿轮 Driving bevel gear of the first drive 1 47 304.31.114-2 半轴 Half shaft 1 48 404B.31.111 右梯形臂 Right steering trapezoid arm 1 49 GB/T308-2002-8.7312G200b 钢球 8.7312G200b Ball 8.7312G200b 1 11/32" 24

7.3 前驱动桥总成 ( 左边减速 )Front Wheel Drive Axle ( Left Side-Slowdown ) 续表 50 GB/T6171-2000-M10 1 螺母 M10 1 Hex. nut M10 1 1 51 504.31.144 紧定螺钉 Set screw 1 M10 1 52 右边减速总成 Right final drive housing assembly 1 25

7.4 前驱动桥总成 (304.31.022-1 部件 ) Front Wheel Drive Axle (304.31.022-1 Assembly) 1 GB/T91-2000-3.2 50 销 3.2 50 Split pin 3.2 50 1 2 304.31.223-1 槽形螺母 Castle nut 1 M27 1.5 3 304.31.224-1 调整垫片 Adjusting shims one set One pcs for each size 4 GB/T3452.1-1992-23.6 2.65 O 形圈 23.6 2.65 O-ring seal 23.6 2.65 1 5 304.31.225-1 主动锥齿轮油封座圈 Oil-seal seat 1 6 HG4-692-67-SD35 56 12 油封 SD35 56 12 Oil-seal SD35 56 12 1 7 GB/T297-1994-32006 轴承 32006 Taper roller bearing 32006 1 8 304.31.227 主动圆锥齿轮 Bevel drive pinion 1 9 GB/T3452.1-1992-85 2.65 O 形圈 85 2.65 O-ring seal 85 2.65 1 10 304.31.226 主动锥齿轮轴承座 Bearing seat 1 11 GB/T297-1994-31306 轴承 31306 Taper roller bearing 31306 1 12 GB/T3452.1-1992-80 2.65 O 形圈 80 2.65 O-ring seal 80 2.65 1 27

7.5 前驱动桥总成 (304.31.014A 部件 ) Front Wheel Drive Axle (304.31.014A Assembly) 1 GB/T297-1994-32009 轴承 32009 Taper roller bearing 32009 2 2 GB/T5782-2000-M8 50 螺栓 M8 50 Hex. head bolt M8 50 4 3 304.31.206 被动圆锥齿轮锁紧片 Lock washer for crown gear 2 4 304.31.207 被动圆锥齿轮 Crown gear 1 5 304.31.210A 半轴齿轮垫圈 Half shaft gear washer 2 6 304.31.211A 差速器半轴齿轮 Half shaft gear 2 7 GB/T119.1-2000-A8 20 销 A8 20 Straight pin A8 20 2 8 304.31.235 左差速器壳体 Left differential housing 1 9 304.31.208A 行星齿轮轴 Planet gear shaft 2 10 304.31.205A 差速器行星齿轮 Planet gear 2 11 304.31.209A-1 行星齿轮垫圈 Planet gear washer 2 12 GB/T119.1-2000-A8 35 销 A8 35 Straight pin A8 35 2 13 304.31.236 右差速器壳体 Right differential housing 1 29

8 前驱动轮总成 Front Drive Wheel 1 304.32.011 轮辋总成 Rim,Front drive wheel 1 2 304.32.011A 轮辋总成 Rim,Front drive wheel 1 2 Optional 2 GB/T2979-1999-7.5-16 驱动轮内胎 7.5-16 Inner Tube 7.5-16 1 2 3 GB/T2979-1999-7.5-16 驱动轮外胎 7.5-16 Cover tyre 7.5-16 1 2 31

9 驱动轮总成 Drive Wheel 1 300.34.102-2 配重螺栓 Bolt for ballast 3 2 2 200.34.118 大垫圈 Big washer 3 2 3 GB/T93-1987-16 垫圈 16 Spring lock washer 16 6 2 4 GB/T6170-2000-M16 螺母 M16 Hex. nut M16 6 2 5 GB/T6176-2000-M14 1.5 螺母 M14 1.5 Fine thread hex. nut M14 1.5 6 2 6 GB/T93-1987-14 垫圈 14 Spring lock washer 14 6 2 7 200.34.117 垫圈 Washer 6 2 8 200.34.115 轮辋螺栓 Attachment bolt 6 2 9 300.34.101-2 后配重 Rear wheel ballast 2 2 10 300.34.103-1 驱动轮辐板 Wheel disc 1 2 11 400-6.34.020 轮辋焊合件 Wheel rim 1 2 12 GB/T2979-1999-12.4-24 驱动轮内胎 12.4-24 Inner tube12.4-24 1 2 13 GB/T2979-1999-12.4-24 驱动轮外胎 12.4-24 Cover tyre 12.4-24 1 2 14 GB/T97.1-2002-16 垫圈 16 Plain washer 16 3 2 33

10.A 摆式牵引装置总成 Tractor Drawbar 1 300.53A.012-1 摆杆式牵引焊合件 Swing Drawbar Frame 1 2 GB/T93-1987-16 垫圈 16 Spring lock washer 16 6 3 GB/T5783-2000-M16 40 螺栓 M16 40 Hex. head bolt M16 40 4 4 300.53.102 牵引 R 销 R-pin 2 5 300.53.109 牵引销 Hitch pin 2 6 300.53A.103 牵引板 Drawbar plate 1 7 GB/T6170-2000-M16 螺母 M16 Hex. nut M16 2 8 GB/T5782-2000-M16 65 螺栓 M16 65 Hex. head bolt M16 65 2 9 300.53.011 销轴焊合件 Spindle 1 10 200.56.011 锁销组合件 Lock pin 1 11 300.53.104-1 牵引卡 Drawbar clamping plate 1 35

10.B 牵引装置总成 ( 旋转式 ) Clevis type 1 300-6.35B.011 牵引架焊合件 Drawbar frame 1 2 GB/T91-2000-8 60 销 8 60 Split pin 8 60 1 3 GB/T6181-1986-M36 3 螺母 M36 3 Hex. Nut M36 3 1 4 GB/T97.1-2002-36 垫圈 36 Plain washer 36 1 5 300-6.35B.101 套筒 Cushion sleeve 1 6 300-6.35B.013 连接架焊合件 Connect frame 1 7 300-6.35.018 插销焊合件 ( 二 ) Hitch pin ( 二 ) 1 37

11 传动轴总成 Transmission shaft 1 404G2.36.012 前套管焊合件 Front housing 1 2 304.36.114 橡胶垫 Rubber pad 1 3 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 4 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 2 5 GB/T5783-2000-M10 20 螺栓 M10 20 Hex. head bolt M10 20 2 6 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 7 254D.36.104 套管吊环 Sleeve ring 2 8 304.36.014 环箍 φ53 总成 Hoop φ53 1 钢丝喉箍 φ50 9 304.36.103 密封套 Seal sleeve 1 10 304.36.015 环箍 φ48 总成 Hoop φ48 1 钢丝喉箍 φ50 11 354G2.36.012 后套管焊合件 Rear housing 1 12 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. head bolt M8 25 3 13 GB/T879.1-2000-4 30 销 4 30 Slotted spring pin 4 30 3 14 GB/T343-1994-I-1.4 热镀锌钢丝 I-1.4 Steel wire I-1.4 按需 need 15 304.36.108 橡胶护罩 Rubber cover 2 16 304.36.101 支承套 Support sleeve 2 17 GB/T308-2002-9 钢球 9 Steel ball 9 12 18 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 3 19 404G2.36.011 传动轴焊合件 Transmission shaft 1 20 304.36.104 挡圈 ( 二 ) Blocking ring (2) 2 21 304.36.105 弹簧 Spring 1 22 304.36.106 密封挡圈 Seal blocking ring 1 23 304.36.107 后球形连接套 Rear connecting-sleeve 1 24 304G2.36.102 后中轴 Rear mid-shaft 1 25 GB/T3452.1-1992-48.7 3.55 O 形圈 48.7 3.55 O-ring seal 48.7 3.55 2 39

11 传动轴总成 Transmission shaft 续表 26 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 2 27 304.36.109 中轴座 Mid-shaft seat 1 28 JB/T7940.1-1995-M10 1 油杯 M10 1 Grease cup M10 1 1 29 304.36.110 纸垫 Paper gasket 1 30 HG4-692-67-PG25 42 10 油封 PG25 42 10 Oil seal PG25 42 10 1 31 GB/T276-1994-6205-Z 轴承 6205-Z Ball bearing with shields 6205-Z 1 32 304.36.113 接合套 Connecting sleeve 1 33 304G2.36.101 中轴套管 Mid-shaft housing 1 40

12.1 变速箱总成 (A) Gearbox(A) 1 504G3.29.020 梭行挡操纵手柄 Shift level handle 1 2 GB/T 845-1985-ST4.2 13 自攻螺钉 ST4.2 13 Bolt ST4.2 13 1 3 504G3-E.29.019 梭行挡操纵杆焊合件 Shift level 1 4 504G3.29.131 防尘罩 Dust cap 1 5 GB/T879.1-2000-(6+4) 26 销 (6+4) 26 Slotted spring pin(6+4) 26 2 6 GB/T5783-2000-M8 60 螺栓 M8 60 Hex. head bolt M8 60 3 7 JB/T7918-1997-K15 19 17 滚动轴承 K15 19 17 Needle roller bearing K15 19 17 2 8 404G2-6F.37.016 万向节组合件 Gimbal 1 9 404G2-6F.37.017 连接支架焊合件 Automotive frame 1 10 404G2-6F.37.125 连接套 Adjusting plate 1 11 GB/T6170-2000-M8 螺母 M8 Hexagon nut M8 1 12 GB/T97.1-2002-8 垫圈 8 Plain washer 8 3 13 GB/T5783-2000-M8 35 螺栓 M8 35 Hex. head bolt M8 35 1 14 404G2-6F.37.122 连接轴 Joint shaft 1 15 504G3.29.112 防护套固定钢丝 Circlip for shaft 28 2 16 504G3.29.127 防护套 Safety cover 1 17 504G3.29.015 万向节组合件 Ⅰ Gimbal Ⅰ 1 18 GB/T879.1-2000-(6+4) 28 销 (6+4) 28 Slotted spring pin(6+4) 28 2 19 404G2-6F.37.121 梭行挡下杆 Joint shaft 1 20 GB/T97.1-2002-16 垫圈 16 Chamfered plain washer 16 1 21 304G2.37.118-1 压簧 Pressure spring 1 22 304G2.37.120 拨杆 Sliding lever 2 23 GB/T879.1-2000-(6+4) 30 销 (6+4) 30 Slotted spring pin (6+4) 30 1 24 304G2.37.128 梭形挡拨头 Patrol sliding block 1 25 GB/T879.1-2000-5 32 销 5 32 Slotted spring pin 5 32 1 42

12.1 变速箱总成 (A) Gearbox(A) 续表 26 GB/T3452.1-1992-15 2.65 O 形圈 15 2.65 O-ring seal 15 2.65 3 27 304G2.37.129 梭形挡拨叉轴 Patrol fork shaft 1 28 GB/T93-1987-10 垫圈 10 Spring lock washer 10 16 29 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. Head bolt M10 25 16 30 200.38.024 放油螺栓总成 Oil drain plug 1 31 JB-FT-CU-16 组合铜垫圈 16 Combined seal washer 16 1 32 300.37.150 底盖 Bottom cover 1 33 300.37.151 纸垫 Paper gasket 1 34 200.38.144-3 衬套 Bush 3 35 404G2-6F.37.110 变速箱壳体 Gearbox housing 1 36 404G2-6F.37.105 高低档拨叉轴 Range gear shift fork shaft 1 37 GB/T894.1-1986-15 挡圈 15 Circlip for shaft 15 2 38 404G2-6F.37.103 高低档拨叉 Shifting fork high - low speed range 1 39 200.37.127-1 拔叉定位弹簧 Positioning spring,shift fork 4 40 GB/T308-2002-9.5 钢球 9.5 Steel ball 9.5 4 41 GB/T879.4-2000-6 24 销 6 24 Slotted spring pin 6 24 2 42 404G2-6F.37.106 Ⅰ-Ⅱ 挡拨叉轴 Shaft,Ⅰ-Ⅱ shift fork 1 43 404G2-6F.37.102 中拨头 Intermediate Sliding block 1 44 404G2-6F.37.101 右拨头 Right Sliding block 1 45 404G2-6F.37.107 Ⅲ-Ⅳ 挡拨叉轴 Shaft,Ⅲ-Ⅳ shift fork 1 46 304G2.37.103 变速箱盖 Gearbox cover 1 47 304G2.37.102 变速箱盖纸垫 Paper gasket, gearbox cover 1 48 304G2.37.114 Ⅰ-Ⅱ 挡拨叉 Ⅰ-Ⅱ Fork 1 49 GB/T75-1985-M8 30 螺钉 M8 30 Blot M8 30 1 43

12.1 变速箱总成 (A) Gearbox(A) 续表 50 304G2.37.112 Ⅲ-Ⅳ 挡拨叉 Ⅲ-Ⅳ Fork 1 51 304G2.37.130 梭形挡拨叉 Patrol fork 1 52 GB/T879.1-2000-5 26 销 5 26 Slotted spring pin 5 26 7 53 JB-FT-CU-12 组合铜垫圈 12 Combined seal washer 12 1 54 GB/T5783-2000-M12 25 螺栓 M12 25 Hex. head bolt M12 25 1 55 304G2.37.155 梭形挡拨叉中轴 Patrol fork middle shaft 1 56 GB/T3452.1-1992-11.2 2.65 O 形圈 11.2 2.65 O-ring seal 11.2 2.65 1 57 450.37.102 互锁销 Mutual locking plunger 1 44

12.2 变速箱总成 (B) Gearbox(B) 1 GB/T276-1994-6208 轴承 6208 Ball bearing 6208 4 2 304G2.37.143 梭行挡前隔圈 Front spacer sleeve,patrol 1 3 304G2.37.141 大衬套 Big bush 2 4 304G2.37.018 梭行挡被动齿轮焊合件 Driven gear,patrol 1 5 450.37.204 同步环 Synthronization ring 6 6 450.37.207 托架 Bracket 9 7 450.37.208 止销 Stop pin 9 8 450.37.206 弹簧 Spring 9 9 304G2.37.142 同步器齿座 Synchronizing gear seat 1 10 450.37.202 滑动齿套 Sliding gear sleeve 3 11 304G2.37.017 前进挡被动齿轮焊合件 Driven dear,advance 1 12 304G2.37.135 中间轴 Counter-shaft 1 13 304G2.37.140 梭行挡后隔圈 Rear spacer,patrol 1 14 304G2.37.139 短隔圈 Short spacer 1 15 304G2.37.138 Ⅳ 挡主动齿轮 Driving gear,Ⅳ Speed 1 16 304G2.37.134 长隔套 Long spacer 2 17 304G2.37.137 Ⅲ 挡主动齿轮 Driving gear,Ⅲ Speed 1 18 304G2.37.136 Ⅱ 挡主动齿轮 Driving gear,Ⅱ Speed 1 19 304G2.37.133 Ⅰ 挡主动齿轮 Driving gear,Ⅰ Speed 1 20 280.37.111 中间轴后轴端挡圈 Rear retaining ring,counter-shaft 1 21 GB/T893.1-1986-28 挡圈 28 Circlip for shaft 28 1 22 300.37.132-1 输出轴接合套 Transmission shaft 1 23 GB/T893.1-1986-55 挡圈 55 Circlip for shaft 55 1 24 GB/T276-1994-6006 轴承 6006 Ball bearing 6006 1 25 GB/T894.1-1986-30 挡圈 30 Circlip for shaft 30 1 46

12.2 变速箱总成 (B) Gearbox(B) 续表 26 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. Head bolt M8 25 4 27 GB/T93-1987-8 垫圈 8 Spring lock washer 8 6 28 280.37.110 中间轴后轴承盖 Rear bearing cover,counter-shaft 1 29 280.37.200/201 调整垫片 Adjusting washer 按需 need 30 304G2.37.132 动力输出传动轴 PTO transmission shaft 1 31 300.37.149-A 动力输出传动齿轮 (1000/540) PTO transmission gear(1000/540) 1 32 GB/T276-1994-6305 轴承 6305 Ball bearing 6305 1 33 GB/T3452.1-1992-73 3.55 O 形圈 73 3.55 O-ring seal 73 3.55 2 34 304G2.37.144 中间轴前轴承盖 Front bearing cover,counter-shaft 1 35 GB/T93-1987-10 垫圈 10 Spring lock washer 10 14 36 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. Head bolt M10 25 10 37 200.37.105 滚针止推圈 Thrust washer,roller 2 38 GB/T309-2000-2.5 19.8 滚针 2.5 19.8 Needle roller 2.5 19.8 28 39 304G2.37.110 主变速前隔圈 Front spacer,main shift 1 40 304G2.37.111 薄衬套 Thin bush 1 41 304G2.37.011 Ⅳ 挡被动齿轮焊合件 Driven gear,Ⅳ Speed 1 42 304G2.37.012 Ⅲ 挡被动齿轮焊合件 Driven gear,Ⅲ Speed 1 43 304G2.37.113 短衬套 Short Bush 2 44 304G2.37.013 Ⅱ 挡被动齿轮焊合件 Driven gear,Ⅱ Speed 1 45 450.37.203 同步器齿座 Synchronizing gear seat 2 46 304G2.37.014 Ⅰ 挡被动齿轮焊合件 Driven gear,Ⅰ Speed 1 47 304G2.37.115 长衬套 Long bush 1 48 304G2.37.116 主变速后隔圈 Rear spacer,main shift 1 49 304G2.37.131 二轴 Shaft Ⅱ 1 47

12.2 变速箱总成 (B) Gearbox(B) 续表 50 GB/T276-1994-6307N 轴承 6307N Snap ring ball bearing 6307N 1 51 GB/T894.1-1986-35 挡圈 35 Circlip for shaft 35 1 52 404G2-6F.37.108 二轴后轴承盖 Rear bearing cover, Shaft Ⅱ 1 53 404G2-6F.37.011 行星机构总成 Planet mechanism 1 54 GB/T93-1987-12 垫圈 12 Spring lock washer 12 4 55 GB/T5782-2000-M12 70 螺栓 M12 70 Hex. head bolt M12 70 4 56 200.37.212 接合齿套 Sliding gear 1 57 GB/T305-1989-80 止动环 80 stopper ring 80 1 58 GB/T276-1994-6307 轴承 6307 Ball bearing 6307 2 59 304G2.37A.102 一轴常啮合齿轮 Constant-mesh gear, shaft I 1 60 300.37.107-2 输入轴油封 Oil seal 1 61 304G2.37.145 隔套 Spacer 1 62 300.37.103-A 输入轴 (1000/540) Input shaft (1000/540) 1 63 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 4 64 404G2-6F.37.109-1 一轴前轴承盖 Front bearing cover, shaft I 1 65 JB/T2600-1980-SG35 55 10 油封 SG35 55 10 Oil seal SG35 55 10 1 66 GB/T3452.1-1992-25 2.65 O 形圈 25 2.65 O-ring seal 25 2.65 1 67 304G2.37.105 中间齿轮轴 Middle Gear Shaft 1 68 304G2.37.104 中间齿轮轴插销 Block pin,middle gear shaft 1 69 JB-FT-CU-10 组合铜垫圈 10 Washer 10 1 70 304G2.37.106 中间齿轮前隔圈 Front spacer,middle gear shaft 1 71 GB/T276-1994-6534905 轴承 6534905 Needle roller bearing6534905 1 72 304G2.37.108 梭行挡中间齿轮 Middle gear,patrol 1 73 304G2.37.109 中间齿轮前隔圈 Front spacer,middle gear shaft 1 48

12.2 变速箱总成 (B) Gearbox(B) 续表 74 GB/T6171-2000-M16 1.5-L 螺母 M16 1.5- 左 Hex. nut M16 1.5-L 1 75 304G2.37.200 同步器总成 Synchronizer assy 1 76 450.37.200 同步器总成 Synchronizer assy 2 49

12.3 行星机构总成 Planet Mechanism System 1 404G2-6F.37.111 齿圈 Ring gear 1 2 404G2-6F.37.112 行星轮架后盖 Rear cover, planet carrier 1 3 200.37.202 行星齿轮轴 Planet gear shaft 3 4 200.37.021 行星架压合件 Planet carrier 1 5 200.37.204 行星轮垫片 Shim,Planet gear 6 6 200.37.207 行星齿轮 Planet gear 3 7 GB/T309-2000-3 19.8 滚针 3 19.8 Needle roller 3 19.8 66 8 200.37.203 行星轮滚针隔圈 Needle bearing retainer 6 9 200.37.205 行星架后垫片 Rear shim, planet carrier 1 10 200.37.201 行星架前垫片 Front shim, planet carrier 1 51

13.1 后桥总成 (A) Rear Axle(A) Ser.No Part No. 名称及规格 Name & Specifications Quantity Remarks 1 300.38.129 主传动主动圆锥齿轮 Spiral-bevel pinion 1 2 GB/T297-1994-32011 滚动轴承 32011 Tapered roller bearing 32011 2 3 GB/T5785-2000-M10 1 30 螺栓 M10 1 30 Fine pitch hex. head bolt M10 1 30 19 4 300.38.139 锁紧垫片 Lock piece 6 5 300.38.140 主传动被动圆锥齿轮 Spiral-bevel gear 1 6 300.38.138-1 差速器壳体 Differential housing 1 7 300.38.147-1 半轴齿轮垫片 Shim,half shaft gear 2 8 300.38.141 半轴齿轮 Half shaft gear 2 9 300.38.143 行星轴 Planet gear shaft 1 10 300.38.148-1 差速器盖 Differential cover 1 11 300.38.144 行星轴固定螺钉 Fixing bolt for planet shaft 1 12 300.38.146 锁紧垫片 Lock piece 4 13 300.38.142 行星齿轮 Planet gear 2 14 300.38.145-1 行星齿轮垫片 Planet gear shim 2 15 GB/T297-1994-30307 滚动轴承 30307 Tapered roller bearing 30307 1 16 200.38.104 主传动主动齿轮调整垫片 Adjusting shim,spiral bevel pinion 1 17 300.38.135 主动齿轮轴承座 Bearing seat,spiral bevel pinion 1 18 GB/T93-1987 垫圈 12 Spring lock washer 12 4 19 GB/T5786-2000-M12 1.5 35 螺栓 M12 1.5 35 Fine thread Hex. head bolt M12 1.5 35 4 20 GB/T297-1994-30207 滚动轴承 30207 Tapered roller bearing 30207 1 21 300.38.134 短隔套 Short spacer sleeve 1 for 2WD 22 200.38.145 甩油片 Oil slinger 1 for 2WD 23 200.38.134 锁片 Lock piece 1 24 200.38.130 锁紧螺母 Lock nut 2 25 200.38.131 止退垫片 Lock washer 1 53

13.2 后桥总成 (B) Rear Axle(B) Ser.No Part No. 名称及规格 Name & Specifications Quantity Remarks 1 404G2-6F.38.101 后桥壳体 Transmission case 1 2 GB/T119.1-2000-10 20 销 10 20 Parallel pin 10 20 2 3 GB/T93-1987-12 垫圈 12 Spring lock washer 12 40 4 GB/T5783-2000-M12 35 螺栓 M12 35 Hex. head bolt M12 35 10 5 300.38.114 提升器壳体纸垫 Paper gasket,upper cover 1 6 GB/T5782-2000-M12 45 螺栓 M12 45 Hex. head bolt M12 45 5 7 GB/T119.1-2000-8 22 销 8 22 Parallel pin 8 22 4 8 JB-FT-CU-16 组合铜垫圈 16 Combination washer 16 1 9 200.38.024 放油螺塞总成 Oil drain plug 1 10 300.38.116 主传动被动齿轮调整垫片 Adjusting shims,spiral crown gear 4 组 11 GB/T6170-2000-M12 螺母 M12 Hex. nut M12 23 12 GB/T898-1988-AM12 40 螺柱 AM12 40 Double end stud AM12 40 31 13 GB/T898-1988-AM12 35 螺柱 AM12 35 Double end stud AM12 35 23 14 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 3 15 GB/T93-1987-8 垫圈 8 Spring lock washer 8 3 16 200.38.160 端盖 End cover 1 17 GB/T3452.1-1992-33.5 3.55 O 形圈 33.5 3.55 O-ring seal 33.5 3.55 1 18 GB/T93-1987-10 垫圈 10 Spring lock washer 10 6 19 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 6 20 300.38.108 小盖板 Small cover 1 for 2WD 21 300.38.109 小盖板纸垫 Paper gasket,small cover 1 22 200.38.144-3 衬套 Bush 2 23 GB/T5782-2000-M12 60 螺栓 M12 60 Hex. head bolt M12 60 2 24 404G2-6F.38.102 变速箱与后桥联接纸垫 Paper gasket 1 55

13.3 操纵机构总成 Operation Mechanism System 1 254G3.37.211 副变速换档杆手柄总成 Handle 1 2 404G2-6F.38.041-1 副变速操纵杆焊合件 Range gear shift lever 1 404G2-6F.38.041A 副变速操纵杆焊合件 Range gear shift lever 1 for EC and AU 3 504G3-3.51.041 固定轴焊合件 ( 一 ) Fixed axis(1) 1 4 504G3.55.218 衬套 (20 20) Sleeve(20 20) 1 5 504G3-3.51.161 尼龙垫圈 Nylon washer 3 6 GB/T5783-2000-M8 25 螺栓 M8 25 Hex.head bolt M8 25 4 7 GB/T93-1987-8 垫圈 8 spring lock washer 8 8 8 504G3-3.51.040 固定板焊合件 ( 一 ) Fixed board(1) 1 9 504G3-3.51.107 密封垫 ( 四 ) Sealing gasket(4) 1 10 GB/T91-2000-3.2 24 销 3.2 24 Split pin 3.2 24 2 11 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 12 254G2.43.102 拉杆叉 Fork 1 13 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 1 14 GB/T882-1986-B10 30 销轴 B10 30 Clevis pin with head B10 30 2 15 404G2-6F.38.043 副变速拉杆焊合件 Secondary change speed pull rod 1 16 404G2-6F.38.042 摇臂焊合件 Swinging arm 1 17 GB/T879.1-2000-6 30 销 6 30 Slotted spring pin 6 30 4 18 GB/T5783-2000-M10 20 螺栓 M10 20 Hex.head bolt M10 20 1 19 GB/T93-1987-10 垫圈 10 spring lock washer 10 5 20 404G2-6F.38.116 限位板 Positioning plate 1 21 404G2-6F.38.111 副变速转轴 Secondary change speed swinging axis 1 22 GB/T3452.1-1992-13.2 2.65 O 形圈 13.2 2.65 O-ring seal 13.2 2.65 2 23 404G2-6F.38.112 副变速操纵拨头 Secondary shift shifting block 1 24 GB/T5783-2000-M10 25 螺栓 M10 25 Hex.head bolt M10 25 4 57

13.3 操纵机构总成 Operation Mechanism System 续表 25 404G2-6F.38.118 侧操纵下盖 Side-control Underneath cover 1 26 GB/T5782-2000-M8 60 螺栓 M8 60 Hex.head bolt M8 60 4 27 404G2-6F.38.113 侧操纵上盖 Side-control above cover 1 28 JB-FT-CU-22 组合铜垫圈 22 Combination washer 22 2 29 404-11.38C.107 堵头螺栓 Plug hex.head bolt 2 30 404-11.38C.115 操纵杆支座 Gear-shift lever base 1 31 GB/T75-1985-M8 14 螺钉 M8 14 Screw M8 14 2 32 GB/T3081-1982-Ⅰ-1.4 260 热镀钢丝 Ⅰ-1.4 260 Galvanized steel wireⅠ-1.40 260 1 33 404-11.38C.117 尼龙座 Nylon base 1 34 GB/T893.1-1986-40 挡圈 40 Circlip for hole 40 1 35 300.37.188 防尘罩 Dust boot 1 36 404G2-6F.38.114 主变速操纵杆 Gear-shift lever 1 404G2-6F.38.114A 主变速操纵杆 Gear-shift lever 1 for EC and AU 37 GB/T6172.1-2000-M10 螺母 M10 Thin hex. nut M10 1 38 404G2-6F.38.117 主变速换挡杆手柄总成 Handle 1 39 404G2-6F.38.016 油尺总成 Dipstick 1 40 JB-FT-CU-12 组合铜垫圈 12 Combination washer 12 1 41 GB/T5786-2000-M12 1.25 16 螺栓 M12 1.25 16 Hex.head bolt M12 1.25 16 1 42 404G2-6F.38.120 外操纵拨头 Outside shifting block 1 43 404G2-6F.38.115 操纵传递杆 Shifting lever 1 44 404-11.38C.105 弹簧 Spring 2 45 404G2-6F.38.119 内操纵拨头 Inner control shifting block 1 58

13.4 差速锁总成 Differential Lock 1 GB/T3452.1-1992-15 2.65 O 形圈 15 2.65 O-ring seal 15 2.65 2 2 300.38.154A 拨叉 Shift fork 1 3 GB/T879.4-2000-5 35 销 5 35 Slotted spring pin 5 35 2 4 GB/T879.4-2000-8 35 销 8 35 Slotted spring pin 8 35 2 5 404G2-6F.38.121 拨叉轴 Shift fork shaft 1 6 200.38.151-1 弹簧 Spring 1 7 300.38.152-1 轴套 Sleeve 1 8 GB/T97.1-2002-20 垫圈 20 Plain washer 20 1 9 404G2-6F.38.032 转轴焊合件 Spindle weldment 1 10 GB/T879.1-2000-8 30 销 8 30 Slotted spring pin 8 30 1 11 404G2-6F.38.031-1 连接板焊合件 junction plate 1 12 GB/T882-1986-B8 24 销轴 B8 24 Clevis pin with head B8 24 1 13 GB/T879.4-2000-6 26 销 6 26 Slotted spring pin 6 26 1 14 304G2-6.38.025 差速锁踏板焊合件 Differential lock pedal board 1 15 304G2-6.38.023 差速锁踏杆焊合件 Differential lock pedal lever 1 16 GB/T97.1-2002-8 垫圈 8 Plain washer 8 1 17 GB/T91-2000-2 20 销 2 20 Split pin 2 20 1 18 GB/T882-1986-B10 30 销轴 B10 30 Clevis pin with head B10 30 2 19 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 20 GB/T91-2000-3.2 24 销 3.2 24 Split pin 3.2 24 2 21 254G2.43.102 拉杆叉 Fork 1 22 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 1 23 404G2-6F.38.033 差速锁拉杆焊合件 Differential lock pull rod 1 24 404G2-6F.38.034 差速锁摇臂焊合件 Differential lock swinging arm 1 25 GB/T3081-1982-Ⅰ-1.4 260 热镀钢丝 Ⅰ-1.4 260 Galvanized steel wireⅠ-1.40 260 1 60

13.4 差速锁总成 Differential Lock 续表 26 300.38.170-1 右接合套 Right splicing sleeve 1 27 300.38.178 紧定螺钉 Set screw with dog point 1 28 300.38.169 左接合套 Left splicing sleeve 1 61

14 最终传动总成 Final Transmission Ser. No. Part No. 名称及规格 Name & Specifications Quantity Remarks 1 GB/T894.1-1986-35 挡圈 35 Circlip for shaft 35 1 2 2 GB/T276-1994-6307 轴承 6307 Snap ring ball bearing 6307 1 2 3 300.39B.101 主动齿轮 Driving gear 1 2 4 300.39.109 轴承座 Bearing seat 1 2 5 GB/T3452.1-1992-103 3.55 O 形圈 103 3.55 O-ring seal 103 3.55 1 2 6 HG4-692-67-SD60 90 12 油封 SD60 90 12 Oil seal SD60 90 12 2 2 7 300.39.113 轴承盖 Bearing cover 1 2 200.39.102 8 GB/T93-1987-12 垫圈 12 Spring lock washer 12 6 2 9 GB/T5783-2000-M12 35 螺栓 M12 35 Hex. head bolt M12 35 6 2 10 300.39.103-3 半轴 Half shaft 1 2 11 300.39.102 后轮毂螺栓 Rear hub bolt 6 2 12 300.39.101 后轮毂螺母 Rear hub nut 6 2 13 200.39.110 纸垫 Paper gasket 1 2 14 GB/T297-1994-30211 圆锥滚子轴承 30211 Tapered roller bearing 30211 1 2 15 300.39.105-2/106-2 左 / 右半轴套管 Right/left half shaft housing 1 2 16 GB/T3452.1-1992-128 3.55 O 形圈 128 3.55 O-ring seal 128 3.55 1 2 17 GB/T297-1994-32014 圆锥滚子轴承 32014 Tapered roller bearing 32014 1 2 18 300.39.110-2 被动齿轮 Driven gear 1 2 19 300.39.114 锁紧螺母 Lock nut 2 2 20 300.39.115 锁紧垫片 Lock pieces 1 2 GB/T858-1988-48 63

15.1 液压转向系统总成 Full Hydraulic Power Steering Gear 1 GB/T6170-2000-M10 螺母 M10 Hex.nut M10 2 2 GB/T93-1987-10 垫圈 10 Spring lock washer 10 2 3 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 4 254G2.40.015-2 转向油箱总成 Oil tank 1 5 GB/T5783-2000-M10 20 螺栓 M10 20 Hex.head bolt M10 20 2 6 JB/T8870-1999-2A(13-20) 喉箍 2A(13-20) Hoop 2A (13-20) 2 7 JB/T8870-1999-2A(16-20) 喉箍 2A(16-20) Hoop 2A (16-20) 3 8 JB/T6015-2000-10-200 胶管 10-200 Rubber pipe 10-200 1 9 JB/T6015-2000-13-200 胶管 13-200 Rubber pipe 13-200 1 10 GB/T93-1987-8 垫圈 8 Spring lock washer 8 10 11 GB/T5783-2000-M8 35 螺栓 M8 35 Hex.head bolt M8 35 4 12 HLCB-D04/06 恒流泵 Constant flow pump 1 13 304G2-6E.40.023 油泵进油管焊合件 Oil delivery pipe weldment 1 14 JB/T7940.2-1995-45 M10 1 油杯 45 M10 1 Grease nipple 45 M10 1 2 15 304.40.127 销 Pin 1 16 304.40.130 挡圈 Circlip stop ring 4 17 304.40.128 防尘罩 Dustproof cover 4 18 GB/T893.1-1986 挡圈 30 Circlip for shaft 30 1 19 304.40.126 上球头座 Upper ball saet 1 20 304.40.129 球接头 Ball connector 1 21 304.40.125 下球头座 Lower ball seat 1 22 GB/T6181-1986-M14 1.5 螺母 M14 1.5 Hex. nut M14 1.5 1 23 GB/T91-2000-3.2 24 销 3.2 24 Split pin 3.2 24 2 24 404-6.40.021 转向油缸总成 Steering cylinder assy 1 25 GB/T6181-2000-M14 螺母 M14 Hex.nut M14 1 65

15.1 液压转向系统总成 Full Hydraulic Power Steering Gear 续表 26 GB/T6181-2000-M14 螺母 M14 Hex. nut M14 1 27 450.31.026-1 转向接头总成 ( 右 ) Connector assy (Right) 1 28 JB/T8870-1999-2A (44-64) 喉箍 2A (44-64) Hoop 2A (44-64) 1 29 304.40A.132 橡胶护套 Rubber jacket 1 30 JB-FT-CU-16 组合铜垫圈 16 Combination washer 16 8 31 300A.40A.011 软管总成 Hose assy 2 32 GB/T3452.1-1992-10.6 2.65 O 形圈 10.6 2.65 O-ring seal 10.6 2.65 4 33 254-8.40.109 两通管夹 Pipe nip 8 34 404-6.40.101 管夹固定板 Oil pipe fixed clip 1 35 404G2-6D.40.011 转向油缸油管焊合件 ( 一 ) Steering cylinder pipe(1) 1 36 404G2-6D.40.012 转向油缸油管焊合件 ( 二 ) Steering cylinder pipe(2) 1 37 404G2-E.40.014 转向油缸软管总成 (B) Hose assy(b) 1 38 404G2-E.40.013 转向油缸软管总成 (A) Hose assy(a) 1 39 GB/T3452.1-1992-7.5 1.8 O 形圈 7.5 1.8 O-ring seal 7.5 1.8 6 40 504G3.40.102 管接头体 Connetor 2 41 GB/T3452.1-1992-20 2.65 O 形圈 20 2.65 O-ring seal 20 2.65 4 42 504G3.40.101 阀块 Valve 1 43 GB/T93-1987-12 垫圈 12 Spring lock washer 12 2 44 GB/T70.1-2000-M12 30 螺栓 M12 30 Hex.head bolt M12 30 2 45 JB/T6013-2000-M16 1.5 铰接螺栓 M16 1.5 Hollow bolt M16 1.5 2 46 404G2-E.40.015 转向器进油软管总成 Oil delivery hose assy 1 47 404G2-E.40.016 转向器回油软管总成 Oil return hose assy 1 48 GB/T6170-2000-M8 螺母 M8 Hex.nut M8 4 49 404G2-6D.40.014 转向器回油管焊合件 Oil return pipe weldment 1 66

15.1 液压转向系统总成 Full Hydraulic Power Steering Gear 续表 50 JB-FT-CU-18 组合铜垫圈 18 Combination washer 18 2 51 250D.58.118 铰接螺栓 M18 1.5 Hollow bolt M18 1.5 1 52 GB/T3452.1-1992-18 2.65 O 形圈 18 2.65 O-ring seal 18 2.65 1 53 GB/T5783-2000-M8 40 螺栓 M8 40 Hex.head bolt M8 40 2 54 GB/T5783-2000-M8 30 螺栓 M8 30 Hex.head bolt M8 30 4 55 404G2-6D.40.013 转向器进油管焊合件 Oil delivery pipe weldment 1 67

15.2 液压转向系统总成 (B)Full Hydraulic Power Steering Gear(B) 1 102S-1-50-07-D 液压转向器 Hydraulic steering gear 1 2 GB/T5783-2000-M8 16 螺栓 M8 16 Hex. head bolt M8 16 2 3 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 4 504G3-E.40.021 底座焊合件 Pedestal 1 5 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 6 GB/T5783-2000-M10 35 螺栓 M10 35 Hex. head bolt M10 35 4 7 GB/T894.1-1986-20 挡圈 20 Circlip for shaft 20 2 8 504G3.40.137 花键轴 Spline 1 9 GB/T276-1994-6004-2Z 轴承 6004-2Z Ball bearing 6004-2Z 1 10 GB/T893.1-1986-42 挡圈 42 Circlip for shaft 42 1 11 504G3.40.037 万向节总成 Gimbal 1 12 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 4 13 GB/T5783-2000-M8 35 螺栓 M8 35 Hex. head bolt M8 35 2 14 504G3.40.157 转向轴 Steering shaft 1 15 550-1.40A.017 方向盘总成 Steering wheel assy 1 16 304.40.112 橡胶轴承 Rubber sleeve 2 17 504G3-E.40.022 支架焊合件 Bracket weldment 1 18 504G3.40.033 销轴焊合件 ( 二 ) Pin(2) 1 19 GB/T6173-2000-M16 1.5 螺母 M16 1.5 Hex. nut M16 1.5 1 20 GB/T97.1-2002-16 垫圈 16 Plain washer 16 1 21 GB/T91-2000-3.2 18 销 3.2 18 Split pin 3.2x18 2 22 GB/T97.1-2002-8 垫圈 8 Plain washer 8 2 23 GB/T882-1986-B8 28 销轴 B8 28 Clevis pin with head B8 28 2 24 5206HX 锁止气弹簧 Gas spring 1 25 132543 释放杆总成 Release lever 1 69

16 动力输出总成 PTO 1 300.41B.103 挡圈 Blocking ring 2 2 300.41B.104 挡圈 Blocking ring 4 3 GB/T309-2000-3 23.8 滚针 3 23.8 Needle roller 3 23.8 78 4 400B.41.106 中间齿轮 (540/1000) Middle gear (540/1000) 1 选装 5 300.41B.107 双速输出中间轴 Middle shaft 1 6 300.41B.109 中间轴定位板 Locating plate of middle shaft 1 7 GB/T93-1987-8 垫圈 8 Spring lock washer 8 7 8 GB/T5783-2000-M8 16 螺栓 M8 16 Hex. head bolt M8 16 2 9 GB/T3452.1-1992-30 2.65 O 形圈 30 2.65 O-ring seal 30 2.65 1 10 GB/T5846-1994-K223020 轴承 K223020 Bearing K223020 1 11 400B.41.117 换档齿轮 (540/1000) Shifting gear (540/1000) 1 12 GB/T276-1994-6209 轴承 6209 Ball bearing 6209 1 13 300.41B.114 动力输出轴 (6 键 ) PTO shaft (of 6 teeth) 1 14 GB/T276-1994-6008 轴承 6008 Ball bearing6008 1 15 GB/T13871.1-2007-FB40 62 8 油封 FB40 62 8 Oil seal FB40 62 8 1 16 300.41B.125 油封挡圈 Oil seal blocking ring 1 17 GB/T3452.1-1992-80 2.65 O 形圈 80 2.65 O-ring seal 80 2.65 1 18 300.41B.115-1 动力输出盖板 Rear cover of rear axle 1 19 300.41.011 防尘盖 PTO shaft shield 1 20 GB/T97.1-2002-8 垫圈 8 Plain washer 8 4 21 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. head bolt M8 25 6 22 400-6.41.011 动力输出护罩 PTO shaft safety cover 1 23 GB/T276-1994-6206 轴承 6206 Ball bearing 206 1 24 GB/T894.1-1986-35 挡圈 35 Circlip for shaft 35 1 25 GB/T893.1-1986-80 挡圈 80 Circlip for hole 80 1 71

16 动力输出总成 PTO 续表 26 GB/T276-1994-6307 轴承 6307 Ball bearing 6307 1 27 400B.41.123A 传动齿轮轴 (540/1000) Driving gear shaft (540/1000) 1 28 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 4 29 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 30 400B.41.102-2 轴承座 Bearing seat 1 31 400B.41.116 双速输出齿轮壳体垫片 Gasket of rear cover 1 32 400B.41.108-1 动力输出壳体 PTO gear housing 1 33 GB/T93-1987-12 垫圈 12 Spring lock washer 12 12 34 GB/T5783-2000-M12 35 螺栓 M12 35 Hex. head bolt M12 35 12 35 504G3.41.104 动力输出操纵杆手柄 PTO control handle 1 36 300.41B.122 锁紧垫片 Lock washer 1 37 300.41B.101 拨叉轴定位板 Locating plate of shift fork shaft 1 38 400B.41.112-1 拨叉 Shift fork 1 39 400B.41.111 拨叉轴 Shift fork shaft 1 40 504G3.55.218 衬套 (20 20) Sleeve(20 20) 1 41 404G2-6F.41.021-1 手柄焊合件 Handle weldment 1 404G2-6F.41.021A 手柄焊合件 Handle weldment 1 for EC and AU 42 400B.41.011-1 转轴焊合件 controlling shaft 1 43 GB/T894.1-1986-15 挡圈 15 Circlip for shaft 15 1 44 GB/T3452.1-1992-10.6 2.65 O 形圈 10.6 2.65 O-ring seal10.6 2.65 2 45 GB/T308-2002-9.5 钢球 9.5 Steel ball 9.5 1 46 200.37.127-1 拨叉定位弹簧 Shift fork positioning spring 1 47 200.38.111 操纵轴衬套纸垫 bushing gasket 1 48 200.38.113 操纵轴衬套 Controlling shaft bushing 1 72

16 动力输出总成 PTO 续表 49 350-1.41.024A-1 弯臂焊合件 Flex arm weldment 1 50 GB/T879.1-2000-6 28 销 6 28 Slotted spring pin 6 28 1 51 GB/T97.1-2002-12 垫圈 12 Plain washer 12 1 52 GB/T91-2000-3.2 20 销 3.2 20 Split pin 3.2 20 2 53 280.43.107 连接叉 Rod clevis 1 54 GB/T882-1986-B12 35 销 B12 35 Clevis pin with head B12 35 1 55 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 1 56 350-1.41.023 传动杆焊合件 Pull rod weldment 1 57 GB/T97.1-2002-10 垫圈 10 Plain washer 10 1 73

17 分动箱总成 Transfer Case 1 304.42.101 中央传动分动齿轮 Power Transfer gear 1 2 GB/T1096-2003-C10 32 键 C10 32 Flat key C10 32 1 3 GB/T65-2000-M5 16 螺钉 M5 16 Cheese head screw M5 16 4 4 GB/T93-1987-5 垫圈 5 Spring lock washer 5 4 5 304.42.133-1 限位板 Locating plate 1 6 GB/T895.1-1986-30 挡圈 30 Circlip for shaft 30 1 7 304.42.104-1 前隔套 Front spacer 1 8 GB5801-86-4524906 轴承 4524906 Needle bearing 4524906 2 9 304.42.105 分动上过轮 Upper idler 1 10 304.42.103 后隔套 Rear spacer 1 11 304.42.116 隔圈 Spacer 2 12 GB/T305-1998-52/57.9 止动环 52/57.9 Locating snap ring 52/57.9 2 13 GB/T276-1994-6205N 轴承 6205N Ball bearing with snap ring groove 6205 2 14 304.42.117 分动下过轮 Lower idler 1 15 304.42.118 小轴 Lower idler shaft 1 16 GB/T879.2-2000-6 50 销 6 50 Slotted spring pin 6 50 1 17 GB/T119.1-2000-A8 30 销 A8 30 Straight pin A8 30 2 18 304.42.109-1 分动箱体 Transfer case housing 1 19 JB-FT-CU-16 组合铜垫圈 16 Combined seal washer16 1 20 200.38.024 放油螺塞总成 Oil drain plug 1 21 GB/T276-1994-6304 轴承 6304 Ball bearing 6304 1 22 304.42.106-1 分动箱齿轮 Sliding gear 1 23 304.42.107 分动箱轴 Transfer case shaft 1 24 GB/T894.1-1986-24 挡圈 24 Circlip for shaft 24 1 25 GB/T893.1-1986-55 挡圈 55 Circlip for hole 55 1 75

17 分动箱总成 Transfer Case 续表 26 HG4-692-67-PG25 42 10 油封 PG25 42 10 Oil seal PG25 42 10 2 27 304.42.108 油封座 Oil seal seat 1 28 GB/T3452.1-1992-45 3.55 O 形圈 45 3.55 O-ring seal 45 3.55 1 29 GB/T276-1994-6205 轴承 6205 Ball bearing 6205 1 30 304.42.012-1 拨杆焊合件 Shift peg 1 31 GB/T879.2-2000-5 32 销 5 32 Slotted spring pin 5 32 1 32 GB/T879.2-2000-8 32 销 8 32 Slotted spring pin 8 32 1 33 GB/T3452.1-1992-15 2.65 O 形圈 15 2.65 O-ring seal 15 2.65 1 34 304.42.111 定位板 Locating plate 1 35 GB/T93-1987-8 垫圈 8 Spring lock washer 8 3 36 GB/T5783-2000-M8 16 螺栓 M8 16 Hex. head bolt M8 16 3 37 404G2-6.42.011 摇臂焊合件 Rocker arm 1 38 404G2-6F.42.013-1 推杆焊合件 Push rod 1 39 GB/T97.1-2002-10 垫圈 10 Washer 10 1 40 GB/T91-2000-3.2 24 销 3.2 24 Split pin 3.2 24 1 41 404G2-6F.42.012 前驱动操纵杆焊合件 Control lever,front wheel drive 1 404G2-6F.42.012A 前驱动操纵杆焊合件 Control lever,front wheel drive 1 for EC and AU 42 GB/T6170-2000-M8 螺母 M8 Nut M8 2 43 GB/T97.1-2002-8 垫圈 8 Washer 8 2 44 454.42.111 限位圈锁紧板 Locking plate 1 45 454.42.110 限位圈 Limit circle 1 46 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 2 47 304G2-6.42.012 限位套焊合件 Stop collar 1 48 GB/T308-2002-9.5 钢球 9.5 Lock ball 9.5 1 76

17 分动箱总成 Transfer Case 续表 49 200.37.127-1 拨叉定位弹簧 Compression spring 1 50 GB/T5783-2000-M12 25 螺栓 M12 25 Hex. head bolt M12 25 1 51 GB/T6171-2000-M10 1 螺母 M10 1 Hex. nut M10 1 1 52 504G3.37.011 前驱动操纵手柄 Control handle 1 77

18 制动器及操纵机构总成 Brake Operation Mechanism 1 404G2-6F.43.018 制动传动轴焊合件 Brake transmission axis 1 2 254G2.43.106 拉杆叉头 Draw rod fork 2 3 504G3.43.101 缓冲垫 Rubber cushion 2 4 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 5 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 4 6 504G3.43.104 支撑板 Support board 1 7 GB/T894.1-1986-25 挡圈 25 Circlip for shaft 25 1 8 504G3.43.135 衬套 (2520) Bush(2520) 2 9 GB/T879.4-2000-8 40 销 8 40 Spring split pin 8 40 1 10 504G3.43.033 右制动踏杆焊合件 Right brake lever weldment 1 11 GB/T13527.2-1992-DT-14 0.6 DT-14 0.6 DT-14 0.6 1 L=23 12 404G2-6F.43.032 左制动踏杆焊合件 Left brake lever weldment 1 13 404G2-6F.43.012 右制动套管焊合件 Left cannula weldment 1 14 404G2-6F.43.126 制动前拉杆 Front pull rod 2 15 504G3.43.103-1 回位弹簧 Return spring 2 16 GB/T6171-2000-M10 1-L 螺母 M10 1( 左 ) Hex. nut M10 1-L 2 17 504G3.43.110 橡胶套 Rubber sheath 2 18 GB/T6171-2000-M10 1 螺母 M10 1 Hex. nut M10 1 4 19 300.21A.148 拉杆叉头 Draw rod fork 2 20 GB/T882-1986-B10 30 销轴 B10 30 Clevis pin with head B10 30 10 21 GB/T97.1-2002-10 垫圈 10 Chamfered plain washer 10 12 22 GB/T91-2000-3.2 20 销 3.2 20 Split pin 3.2 20 14 23 404G2-6F.43.011 左制动套管焊合件 Right cannula weldment 1 24 JB/T7940.1-1995- M10 1 油杯 M10 1 Angle grease nipple M10 1 4 25 GB/T894.1-1986-22 挡圈 22 Circlip for shaft 22 1 79

18 制动器及操纵机构总成 Brake Operation Mechanism 续表 26 404G2-6F.43.019 制动后拉杆焊合件 Rear brake pull link weldment 1 27 254G3.38.118 回位弹簧 Hand brake return spring 2 28 404G2-6F.43.013 手制动左套管焊合件 Left hand brake cannula weldment 1 29 404G2-6F.43.016 手制动左拉线安装板焊合件 Left hand brake stay wire mounting pane 1 30 404G2-6F.43.020 手制动拉杆焊合件 Hand brake pull link weldment 2 31 GB/T 6170-2000-M10 螺母 M10 Hex. nut M10 4 32 280.43.107 连接叉 Rod clevis 4 33 300.43.151 制动器盖 Brake cap 2 34 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 26 35 GB/T93-1987-10 垫圈 10 Spring lock washer 10 26 36 300.43.153 纸垫 Brake gasket 2 37 450.43.113 螺栓 Hex. head bolt 4 38 450.43.114 拉板 Draw plate 4 39 GB/T882-1986-B10 32 销轴 B10 32 Clevis pin with head B10 32 2 40 300.43.161 调节杆 Adjustting rod 2 41 GB /T6170-2000-M12 螺母 M12 Hex. nut M12 12 42 404G2-6F.43.108 左制动摇臂 Left brake rocker arm 1 43 280.43.105 自位垫块 Self-aligning block 2 44 404G2-6F.43.014 手制动右套管焊合件 Right hand brake cannula weldment 1 45 GB/T894.1-1986-24 挡圈 24 Circlip for shaft 24 3 46 404G2-6F.43.015 手制动右拉线安装板焊合件 Right hand brake stay wire mounting pan 1 47 404G2-6F.43.101 制动后传动轴 Rear brake transmission axis 1 48 GB/T882-1986-B12 70 销轴 B12 70 Clevis pin with head B12 70 2 49 404G2-6F.43.022 左制动拉线组合件 Left hand brake stay wire 1 80

18 制动器及操纵机构总成 Brake Operation Mechanism 续表 50 300-6.43.015 手制动组合件 Hand brake 1 Optional 504G3-3.43.025 手制动操纵合件 Hand brake 1 for EC and AU 51 404G2-6F.43.021 右制动拉线组合件 Right hand brake stay wire 1 52 GB/T882-1986-B10 40 销轴 B10 40 Clevis pin with head B10 40 2 53 GB/T882-1986-B16 40 销轴 B16 40 Clevis pin with head B16 40 1 54 GB/T97.1-2002-16 垫圈 16 Chamfered plain washer 16 1 55 GB/T91-2000-4 25 销 4 25 Split pin4 25 1 56 504G3-3.51.110 制动操纵压板 Brake control device keep plate 1 Optional 57 504G3-3.51.111 密封垫 ( 五 ) Rubber blanket 1 Optional 58 GB/T91-2000-3.2 28 销 3.2 28 Split pin 3.2 28 2 59 404G2-6F.43.025 手制动手柄安装座 Hand brake fix board 1 Optional 60 404G2-6F.43.109 右制动摇臂 Right brake rocker arm 1 61 280.43.118-1 密封套 Seal cartridge 2 62 280.43.110 右摇臂支座 Right rocker arm pedestal 1 63 280.43.104 左摇臂支座 Left rocker arm pedestal 1 64 300.43.163-1 右制动器壳体 Right brake housing 1 65 280.43.103 纸垫 Paper gasket 2 66 GB/T898-1988-AGM12-M12 35 螺柱 AGM12-M12 35 Double end stud AGM12-M12 35 8 67 GB/T3452.1-1992-10.6 2.65 O 形圈 10.6 2.65 O Type ring10.6 2.65 8 68 GB/T819.2-1997-M8 25 十字槽沉头螺钉 M8 25 Cross deep bolt M8 25 8 69 GB/T894.1-1986-35 挡圈 35 Circlip for shaft 35 2 70 HG4-692-67-SG32 52 12 油封 SG32 52 12 Oil seal SG 32 52 12 2 71 300.43.152-1 左制动器壳体 Left brake housing 1 72 300.43.154-1 制动片 Brake piece 2 81

18 制动器及操纵机构总成 Brake Operation Mechanism 续表 73 404G2AU.43.024 从动盘总成 Brake driven disk 4 for EC and AU 300.43.024 从动盘总成 Brake driven disk 4 74 300.43.160 压盘 Brake pressure plate 4 75 450.43.112 内回位弹簧 Return spring 6 76 GB/T308-1989-7/8" 钢球 7/8" Steel ball 7/8" 10 77 GB/T882-1986-B12 75 销轴 B12 75 Clevis pin with head B12 75 2 82

19 座椅总成 Seat 1 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 2 GB/T5783-2000-M8 20 螺栓 M8 20 Bolt M8 20 4 3 DS44/1HB 座椅 Seat 1 XL-SEAT-003 座椅 Seat 1 Optional YHG6-S23 座椅 Seat 1 Optional 84

20.1 安全架总成 Safety Frame 1 304-9A.46.011 左安全架座焊合件 Left bracket,safety frame 1 2 GB/T 889.2-2000-M20 1.5 螺母 M20 1.5 Hex. nut M20 1.5 2 3 304-9A.46.014 锁销合件 Lock pin 2 4 GB/T5783-2000-M12 45 螺栓 M12 45 Hex. head bolt M12 45 2 5 GB/T 6170-2000-M12 螺母 M12 Hex. nut M12 2 6 GB/T5783-2000-M12 65 螺栓 M12 65 Hex. head bolt M12 65 2 7 GB/T 97.1-2002-16 垫圈 16 Plain washer 16 8 8 GB/T 93-1987-16 垫圈 16 Spring lock washer 16 8 9 GB/T5783-2000-M16 45 螺栓 M16 45 Hex. head bolt M16 45 8 10 GB/T5785-2000-M20 1.5 110 螺栓 M20 1.5 110 Hex. head bolt M20 1.5 110 2 11 404G2-6F.46.011 安全架焊合件 Safety Frame 1 12 254-5.49.103 手册资料筒 Manual holder 1 13 GB/T 6170-2000-M8 螺母 M8 Hex. nut M8 4 14 254G3.46.103 抱箍固定板 Fixed plate 2 15 254G3.46.104 橡胶固定板 Shim plate 2 16 304-9A.46.161 U 形螺栓 U-bolt 2 17 304-9A.46.012 右安全架座焊合件 Right bracket,safety frame 1 18 GB/T 97.1-2002-20 垫圈 20 Plain washer 20 2 19 GB/T 97.1-2002-27 垫圈 27 Plain washer 27 4 20 504G3.46.115 橡胶垫圈 Rubber washer 4 86

20.2 前安全架总成 Front Safety Frame 1 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 8 2 304G2-6E.46.021 前安全架焊合件 Front safety frame 1 3 GB/T93-1987-10 垫圈 10 Spring lock washer 10 8 88

21.1 机罩仪表罩总成 (A) Hood and Panel(A) 1 404G2-6F.47.011-1 机罩焊合件 Engine Hood 1 2 GB/T91-2000-3.2 30 销 3.2 30 Split pin 3.2 30 2 3 GB/T97.1-2002-10 垫圈 10 Plain washer 10 6 4 GB/T882-1986-B10 60 销轴 B10 60 Clevis pin with head B10 60 2 5 695 293 320-BB-832678 压缩气弹簧 832678 Gas spring 2 6 504G3-E.47.105 油箱盖 Fuel tank cap 1 7 404-11.47.105 左侧风窗 Left radiator grill 1 8 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 9 GB/T6170-2000-M8 螺母 M8 Hex. Nut M8 4 10 GB/T97.1-2002-8 垫圈 8 Plain washer 8 2 11 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 2 12 404-11.47.017 灯架焊合件 Bracket 1 13 404-11.47.103 前风窗 Front cover 1 14 GB/T5783-2000-M6 16 螺栓 M6 16 Hex. head bolt M6 16 19 15 GB/T97.1-2002-6 垫圈 6 Plain washer 6 19 16 GB/T93-1987-6 垫圈 6 Spring lock washer 6 23 17 GB/T6170-2000-M6 螺母 M6 Hex. Nut M6 26 18 300.47.113 标牌安装板 Brand mark plate carrier 1 19 GB/T6170-2000-M5 螺母 M5 Hex. Nut M5 2 20 GB/T93-1987-5 垫圈 5 Spring lock washer 5 2 21 GB/T97.1-2002-5 垫圈 5 Plain washer 5 2 22 404-11.47.107 DF 标牌 DF brand 1 23 404-11.47.109 左右装饰带 Decorative strip 1 24 404-11.47.117 机罩开启指示 Hood opening instruction 1 25 404-11.47.104 下风窗 Front garnish 1 90

21.1 机罩仪表罩总成 (A) Hood and Panel(A) 续表 26 404-11.47.106 右侧风窗 Right radiator grill 1 27 GB/T5783-2000-M6 35 螺栓 M6 35 Hex. head bolt M6 35 4 28 550.47E.105-1 机罩锁套 Rubber sheath 1 29 550.47E.026 机罩锁组合件 Hood lock 1 30 404G2-6F.47.015-1 锁销焊合件 Lockpin 1 31 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 32 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 4 33 404G2-E.47.141-1 右前下支架 Front down right setting board 1 34 404G2-E.47.041 右下侧板焊合件 Right Hood 1 35 404G2-E.47.131-1 左前下支架 Front down left setting board 1 36 400-6.47.105 右上安装板 Top right setting board 1 37 300-6.47.103 右下安装板 Down right setting board 1 38 304-6E.47.103 左上安装板 Top left setting board 1 39 404G2-E.47.142 右后上支架 Rear top right setting board 1 40 404G2-E.47.031 左下侧板焊合件 Left Hood 1 41 404G2-6F.47.014 机罩铰链焊合件 Hood hinge 2 91

21.2 机罩仪表罩总成 (B) Hood and Panel(B) 1 GB/T5783-2000-M6 20 螺栓 M6 20 Hex. head bolt M6 20 12 2 GB/T93-1987-6 垫圈 6 Spring lock washer 6 16 3 GB/T97.1-2002-6 垫圈 6 Plain washer 6 16 4 504G3.47.103 方向器底座罩壳 Redirector pedestal mantle 1 5 GB/T97.1-2002-8 垫圈 8 Plain washer 8 12 6 GB/T93-1987-8 垫圈 8 Spring lock washer 8 12 7 GB/T5783-2000-M8 16 螺栓 M8 16 Hex. head bolt M8 16 12 8 GB/T818-2000-M6 16 螺钉 M6 16 Philips pan head screw M6 16 5 9 504G3.47.102 方向器后罩壳 Redirector back mantle 1 10 404G2-6F.47.016 左框架焊合件 Left frame clsss weldment 1 11 504G3.47.014 方向器前罩壳组合件 Redirector forward mantle 1 12 GB/T5783-2000-M10x25 螺栓 M10x25 Hex. head bolt M10x25 4 13 GB/T97.1-2002-5 垫圈 5 Plain washer 5 2 14 404G3.47.101 仪表罩 Engine Hood 1 15 YC0542020445 仪表台密封条 Dashboard rubber ring 1 L=1700 16 404G2-E.47.021 仪表罩框架焊合件 Hood frame clsss weldment 1 17 GB/T5846-1989-K25 31 25 滚针轴承 K25 31 25 Needle bearing K25 31 25 2 18 A3-1 后视镜 (EC) Rearview mirror 2 19 800.47.101 密封胶条 Rubber ring 1 L=1340 20 404G2-6F.47.018 右框架焊合件 Right frame clsss weldment 1 21 404G3.47.161 挡风玻璃 Windshield 2 22 504G3.51.102 橡胶套 Rubber sheath 2 23 504G3.47.225 玻璃固定用螺母 M5 Hex. Nut M5 6 24 504G3.47.226 玻璃固定用橡胶垫 5 Rubber washer 5 6 25 504G3.47.227 玻璃固定用塑料垫 5 Plastic washer 5 6 93

21.2 机罩仪表罩总成 (B) Hood and Panel(B) 续表 26 GB/T96.2-1985-6 垫圈 6 Plastic washer 6 12 27 GB/T93-1987-5 垫圈 5 Spring lock washer 5 6 28 GB/T818-2000-M5 8 螺钉 M5 8 Philips pan head screw M5 8 6 29 504G3.47.108 线束橡胶套 wiring harness rubber cover 1 30 GB/T818-2000-M8 12 螺钉 M8 12 Philips pan head screw M8 12 2 31 404G2-6F.47.015-1 锁销焊合件 Lockpin 1 32 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 33 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 4 34 404G2-E.47.041 右下侧板焊合件 Right Hood 1 35 404G2-E.47.031 左下侧板焊合件 Left Hood 1 94

22 电气系统总成 Electrical System 1 304G2-6E.48.016 蓄电池正极 - 总电源开关连接电缆总 Elastic cable paper 1 2 6-QW-80L 免维护蓄电池 Battery 1 3 254G3.48.019 总电源开关 (DHKG904) General supply switch 1 4 304G2-6E.48.015 起动 - 电源总开关连接电缆线 Elastic cable paper 1 5 504G3.48.021 S116 转向灯 Steering lamp 2 6 504G3.48.104 油压传感器 Oil pressure sensor 1 7 504G3.48.103 转速传感器 (M18 1.5) rotation speed senser(m18 1.5) 1 8 404G2-E.48.012-1 主线束 Main wiring harness 1 9 404G2-6F.48.014-1 右挡泥板线束 Right fender wiring harness 1 10 504G3.48.020 保险丝盒 Fuse box wiring harness 1 11 504G3.48.027 三联板开关盖板 (JK938A)Caution light swich cover plate 1 12 1912 型起动继电器 (12V 40A) Starting relay 6 13 300-6.48.023-1 回复反射器 Reflector 2 14 504G3.48A.104 PNP 接近传感器 approach switch 2 15 404G2-6F.48.015-1 左挡泥板线束 Left fender wiring harness 1 16 300-6.48.019-1 牌照灯 Rear registration plate lamp 1 17 JB3762-84 拖车插座 Tow truck jack 1 18 804-6.48.024 后工作灯 Tail lamp 1 19 404-11.48.022/023 左 / 右后尾灯 Combination rear signal lamp 2 20 AG-057 线卡 Wire clip 1 21 HY-SG102A 电子闪光器 Flasher 1 22 FT111 电子调节器 Voltage ragulater 1 23 JB1041 起动安全开关 Security switch 2 24 504G3.48.026 三联板开关 (JK938A) Caution light swich 1 25 304G2-6.48.103 组合开关 Multi-function switch 1 96

续表 22 电气系统总成 Electrical System 26 504G3.48.022 预热起动开关 Pre-heating starting switch 1 27 504G3.48.105-1 起动开关标牌 Starting scutcheon 1 28 主继电器 Main relay 1 线束带 29 504G3.48.014 预热器接地线 Preheater ground lead 1 30 504G3-E.48A.021 组合仪表 (EC) Combination meter 1 31 250D.48.101 电缆接头护套 Cable splice jacket 1 32 404G2-6F.48.102 油量传感器 Oil level sensor 1 33 JK231B 制动灯开关 Brakelight switch 1 34 404G2-E.48.101 延时继电器安装板 Relay installation 1 35 200.48B.108 线夹 Wire clip 3 36 504G3.48.102 水温传感器 Water temperature sensor 1 37 304G2-6E.48.017 蓄电池负极搭铁电缆 Battery cable 1 38 404-11.48.020/021 左 / 右前大灯 Head lamp 2 39 DL-124D 电喇叭 Electrucity horn 1 40 504G3.48A.011 前线束 Front wiring harness 1 41 CX-2 型免维护蓄电池电缆线护套 Jacket 2 97

23 工具箱总成 Toolbox 1 450.49.001 工具箱 Toolbox 1 2 GB/T97.1-2002-8 垫圈 8 Plain washer 8 2 3 GB/T93-1987-8 垫圈 8 Spring lock washer 8 2 4 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 2 5 GB/T5783-2000-M8 16 螺栓 M8 16 Hex. head bolt M8 16 2 99

100

24 燃油箱总成 Fuel tank 1 JB/T6013-2000-M12 1.25 铰接螺栓 M12 1.25 Hollow bolt M12 1.25 1 2 DF-4268 油箱盖 Fuel tank cap 1 3 404G2-6F.50.011-1 燃油箱合件 Fuel tank 1 4 404G2-6F.50.101-1 油箱挡板 Adiabatic board 1 5 404G2-6F.50.102-1 隔热毡 Heat insulation felt 1 6 JB-FT-CU-12 组合铜垫圈 12 Combination washer 12 4 7 GB/T5786-2000-M12 1.25 16 螺栓 M12 1.25 16 Hex.head bolt M12 1.25 16 1 8 GB/T5783-2000-M8 40 螺栓 M8 40 Hex.head bolt M8 40 4 9 304G2-6.50.101 油箱垫圈 Fuel tank washer 4 10 200.50.015 燃油滤清管路总成 Fuel pipe laying 1 国三,10A-400 300.50.015B 燃油滤清管路总成 Fuel pipe laying 1 出口 11 304G2-6.50.102 橡胶垫 Rubber pad 2 12 404G2-6F.50.014-3 油箱支架焊合件 Fuel tank bracket 1 13 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 14 GB/T5783-2000-M10 25 螺栓 M10 25 Hex.head bolt M10 25 4 15 GB/T97.1-2002-8 垫圈 8 Plain washer 8 4 16 GB/T93-1987-8 垫圈 8 Spring lock washer 8 4 17 GB/T6170-2000-M8 螺母 M8 Hex.nut M8 4 101

102

25 地板挡泥板总成 Foot Mud Shields Rest 1 404G2-6D.51.011 后支撑架焊合件 Rear bracket 2 2 504G3.51.011-1 踏梯焊合件 Ladder frame 2 3 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 18 4 GB/T93-1987-8 垫圈 8 Spring lock washer 8 26 5 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. head bolt M8 25 26 6 404G2-6F.51.035 左前支撑架焊合件 Left-front backstop 1 7 GB/T5783-2000-M16 35 螺栓 M16 35 Hex. head bolt M16 35 10 8 GB/T93-1987-16 垫圈 16 Spring lock washer 16 30 9 GB/T91-2000-3.2 32 销 3.2 32 Split pin 3.2 32 4 10 GB/T6181-1986-M16 螺母 M16 Hex. nut M16 4 11 504G3.51.124 减震圈 Rubber damping ring 10 12 404G2-6F.51.411 前护套 Front damping block sleeve 2 13 404G2-6F.51.036 右前支撑架焊合件 Right-front backstop 1 14 504G3-E.45.026 限位套焊合件 Limiting stopper 4 15 504G3.51.123 护罩 Damping protecting cover 4 16 504G3.51.127 橡胶垫 Rubber pad 6 17 GB/T31.1-1988-M16 110 螺栓 M16 110 Hex. head bolt M16 110 2 18 404G2-6D.51.101 前地板橡胶垫 Rubber floor 1 19 404G2-6D.51.013 盖板合件 Cover plate combination 1 20 GB/T6170-2000-M5 螺母 M5 Hex. nut M5 4 21 GB/T93-1987-5 垫圈 5 Spring lock washer 5 4 22 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 4 23 GB/T93-1987-10 垫圈 10 Spring lock washer 10 12 24 GB/T97.1-2002-10 垫圈 10 Plain washer 10 4 25 404-11.51.104 扶手 Handle hold 2 103

25 地板挡泥板总成 Foot Mud Shields Rest 续表 26 GB/T67-2000-5 25 螺钉 M5 25 Screw M5 25 4 27 254G3.51.122 变速杆挡板 Selector board 1 28 254G3.51.114 防尘套 Rubber sheath 1 29 404-11.51.026 右尾灯安装架焊合件 Right taillight bracket rest 1 30 GB/T6170-2000-M16 螺母 M16 Hex. nut M16 20 31 GB/T97.1-2002-16 垫圈 16 Plain washer 16 16 32 GB/T5782-2000-M16 50 螺栓 M16 50 Hex. head bolt M16 50 8 33 404G2-E.51.018 右挡泥板焊合件 Right mud shields rest 1 34 404G2-E.51.011 地板框架焊合件 Foot mud shields welding joint 1 35 404G2-E.51.015 座椅支架焊合件 Seat bracket 1 36 404G2-E.51.016 座椅封板焊合件 Squab panel 1 404G2-E.51.105 座椅后封板 Squab panel 1 Optional 37 304G2-6.51.031 挂钩组合件 Suspender 1 38 304G2-6E.51.101 后牌照板 Rear license plate 1 39 504G3.47.151 橡胶套 ( 二 ) rubber ring(2) 2 40 404G2-6C.51.106 后封板支架 Squab panel bracket 41 404G2-E.51.017 左挡泥板焊合件 Left mud shields rest 1 42 304G2-6.51.106 电瓶线护圈 Electrical wire guard ring 1 43 354-1.47.307 拖车插座安装板 Trailer socket plate 1 44 GB/T97.1-2002-8 垫圈 8 Plain washer 8 26 45 404-11.51.025 左尾灯安装架焊合件 Left taillight bracket rest 1 46 GB/T31.1-1988-M16 150 螺栓 M16 150 Hex. head bolt M16 150 2 47 404G2-6F.51.421 后护套 Rear damping block sleeve 1 48 404G2-6F.51.422 挡板 Baffle 1 104

25 地板挡泥板总成 Foot Mud Shields Rest 续表 49 GB/T5782-2000-M16 175 螺栓 M16 175 Hex. head bolt M16 175 8 105

106

26.1 提升器操纵机构总成 Hydraulic Power Lift Operation Mechanism System 1 GB/T 6170-2000-M6 螺母 M6 Hex. nut M6 2 2 GB/T 93-1987-6 垫圈 6 spring lock washer 6 2 3 GB/T 5783-2000-M6 16 螺栓 M6 16 Hex.head bolt M6 16 2 4 404G2-6C.55.121 摇臂 Rocker 1 5 GB/T882-2000-B10 30 销轴 B10 30 Clevis pin with head B10 30 2 6 504G3.37.090 拉杆焊合件 Pull rod 1 L=105 404G2-6F.55.090 拉杆焊合件 Pull rod 1 L=120,Optional 404G2-6F.55.090A 拉杆焊合件 Pull rod 1 L=135,Optional 7 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 8 GB/T91-2000-3.2 25 销 3.2 20 Split pin 3.2 25 2 9 GB/T 6170-2000-M10 螺母 M10 Hex. nut M10 1 10 254G2.43.102 拉杆叉 Pullback fork 1 11 504G3-3.51.161 尼龙垫圈 Nylon washer 2 12 504G3.55.218 衬套 (20 20) Sleeve(20 20) 1 13 404G2-6C.55.023 提升手柄焊合件 Handle assy 1 14 1204.55.108 位控制手柄 Handle 1 15 GB/T 5783-2000-M8 25 螺栓 M8 25 Hex.head bolt M8 25 2 16 GB/T 93-1987-8 垫圈 8 spring lock washer 8 2 17 504G3-3.51.051 固定轴焊合件 ( 二 ) Fixed axis(2) 1 18 504G3-3.51.050 固定板焊合件 ( 二 ) Fixed board(2) 1 19 504G3-3.51.106 密封垫 ( 三 ) Sealing gasket(3) 1 107

108

26.2 分配器总成 Hydraulic Oil Distributor Ser.No. Part No. 名称及规格 Name & specifications Quantity Remarks 1 GB/T5783-2000-M6 20 螺栓 M6 20 Hex. head bolt M6 20 4 2 GB/T93-1987-6 垫圈 6 Spring lock washer 6 8 3 200.55.131 端盖 End cover 1 4 200.55.132 端盖纸垫 Paper gasket 1 5 GB/T3289.31-1982-R1/4 外方管堵 R1/4 Square head oil plug R1/4 1 6 200.55.126-A 分配器壳体 Distributor body 1 7 GB/T93-1987-8 垫圈 8 Spring lock washer 8 3 8 GB/T70.1-2000-M8 25 螺钉 M8 25 Hex.socked cap screwm8 25 2 9 GB/T5781-2000-M8 75 螺栓 M8 75 Hex. head bolt M8 75 1 10 GB/T880-1986-6 30 销 6 30 Pin 6 30 1 11 GB/T91-2000-1.6 10 销 1.6 10 Split pin 1.6 10 2 12 200.55.128 拔叉 Fork 1 13 GB/T3452.1-1992-10.6 1.8 O 形圈 10.6 1.8 O-ring seal 10.6 1.8 2 14 404G2-6F.55.013 手柄焊合件 Handle pole 1 15 200.55.129-1 定位螺钉 Positioning bolt 1 16 JB-FT-CU-14 组合铜垫圈 14 Combination washer 14 1 17 200.55.130 定位弹簧 Positioning spring 1 18 GB/T5783-2000-M6 60 螺栓 M6 60 Hex. head bolt M6 60 4 19 GB/T308-2002-9.5 钢球 9.5 Steel ball 9.5 1 20 200.55.123 拔叉盒 Fork box 1 21 200.55.125 拔叉盒纸垫 Paper gasket 1 22 200.55.127 操纵阀 Sliding valve 1 23 GB/T879.1-2000-6 22 销 6 22 Slotted spring pin 6 22 1 24 GB/T3452.1-1992-17 2.65 O 形圈 17 2.65 O-ring seal 17 2.65 2 25 GB/T3452.1-1992-10.6 2.65 O 形圈 10.6 2.65 O-ring seal 10.6 2.65 1 109

26.2 分配器总成 Hydraulic Oil Distributor 续表 Ser.No. Part No. 名称及规格 Name & specifications Quantity Remarks 26 200.55.138 垫块 Pad 1 27 GB/T308-2002-9 钢球 9 Steel ball dia.9 1 28 200.55.137 球座 Ball seat 1 29 200.55.136 套管 Sleeve 1 30 200.55.135-1 安全阀弹簧 Safty valve Spring 1 31 200.55.134 调节垫片 Adjusting shims 2~5 32 200.55.133 螺塞 Plug 1 33 404G2-6F.55.011 分配器总成 Hydraulic Oil Distributor 1 110

111

26.3 提升器总成 Hydraulic Power Lift 1 GB/T5783-2000-M10 25 螺栓 M10 25 Hex. head bolt M10 25 2 2 GB/T93-1987-10 垫圈 10 Spring washer 10 6 3 200.55.105 提升臂销 Lift arm pin 2 4 GB/T93-1987-16 垫圈 16 Spring washer 16 2 5 GB/T6170-2000-M16 螺母 M16 Hex. nut M16 2 6 GB/T93-1987-14 垫圈 14 Spring washer 14 4 7 GB/T5782-2000-M14 50 螺栓 M14 50 Hex. head bolt M14 50 4 8 300.55.114-1 油缸盖 Cylinder cover 1 9 300.55.125 调节阀 adjust valve 1 10 GB/T3452.1-1992-11.8 1.8 O 形圈 11.8 1.8 O-ring seal 11.8 1.8 2 11 GB/T119.1-2000-4 12 销 4 12 Pin 4 12 1 12 300.55.127 调节阀杆下端 The lower end of adjust valve 1 13 GB/T879.1-20004 16 销 4 16 Pin 4 16 1 14 300.55.122 调节阀杆上端 The lower top of adjust valve 1 15 GB/T879.1-2000-5 24 销 5 24 Pin 5 24 1 16 300.55.124 垫圈 30 Spring washer 30 1 17 300.55.130 阀杆螺母 Valve -pole nut 1 18 300.55.020 手轮胶合件 Handwheel assy 1 19 GB/T3452.1-1992-10.6 1.8 O 形圈 10.6 1.8 O-ring seal 10.6 1.8 1 20 JB1000-77-M14 1.5 螺塞 M14 1.5 Plug M14 1.5 2 21 JB-FT-CU-14 组合铜垫圈 14 Combination washer 14 2 22 200.55.124 铰接螺栓 M14 1.5 Hex. head bolt M14 1.5 1 23 200.55.165 夹紧板 Pressing Plate 1 24 GB/T5782-2000-M12 50 螺栓 M12 50 Hex. head bolt M12 50 1 25 200.55.022-1 输出油管焊合件 Out-let pipe 1 112

26.3 提升器总成 Hydraulic Power Lift 续表 26 GB/T97.1-2002-8 垫圈 8 Plain washer 8 1 27 GB/T91-2000-2 16 销 2 16 Split pin 2 16 2 28 300-6.55.010 联动杆焊合件 Linkage rod 1 29 200.55.119-1 挡块 Limit spot 2 30 GB/T6170-2000-M8 螺母 M8 Hex. nut M8 4 31 GB/T5783-2000-M8 20 螺栓 M8 20 Hex. head bolt M8 20 2 32 300-6.55.106 外提升臂 Lift arm 2 33 200.55.120 联动销 Linkage pin 1 34 200.55.107 压板 Clamping plate 2 35 GB/T3452.1-1992-92.5 5.3 O 形圈 92.5 5.3 O-ring seal 92.5 5.3 1 36 300.55.115 油缸 Cylinder 1 37 GB/T93-1987-12 垫圈 12 Spring washer 12 1 38 300.55.101-2 提升器壳体 Lift case 1 39 GB/T70.1-2000-M8 25 内六角螺钉 M8 25 Hex. head bolt M8 25 2 40 200.55.111-2 通气螺塞 Vent tube 1 41 GB/T93-1987-8 垫圈 8 Spring washer 8 3 42 GB/T5783-2000-M8 75 螺栓 M8 75 Hex. head bolt M8 75 1 43 200.55.102 隔套 Spacer sleeve 2 44 200.55.103A 衬套 Bush 2 45 GB/T3542.1-1992-38.7 5.3 O 形圈 38.7 5.3 O-ring seal 38.7 5.3 2 46 200.55.104 隔套 Spacer sleeve 2 47 200.55.122 挡盘 Retainer plate 1 48 GB/T91-2000-3.2 20 销 3.2 20 Split pin 3.2 20 1 49 GB/T97.1-2002-10 垫圈 10 Plain washer 10 1 113

26.3 提升器总成 Hydraulic Power Lift 续表 50 200.55.014 拨盘焊合件 Driven plate 1 51 200.55.016 传动盘焊合件 Drive plate weldment 1 52 200.55.121 扭簧 Torsion spring 1 53 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 4 54 300.55.024 右挂接板焊合件 Right Hitching plate 1 55 300.55.025 左挂接板焊合件 Left Hitching plate 1 56 300.55.132-1 内提升臂 Inner lift arm 1 57 GB/T879.1-2000- 6 50 销 6 50 Slotted spring pin 6 50 1 58 200.55.109 活塞顶杆 Piston push rod 1 59 300.55.117 YX 形密封圈 D80 YX-seal D80 1 60 300.55.116 活塞 Piston 1 61 GB/T3452.1-1992-73 3.55 O 形圈 73 3.55 O-ring seal 73 3.55 1 62 300.55.135 提升轴 Lift shaft 1 114

115

27 悬挂装置总成 Suspension Mechanism 1 200.56.016 上拉杆连接销总成 Coupling pin of upper link 2 2 300.56.020-1 上拉杆后调节杆总成 Upper link rear adjusting rod 1 3 300.56.030-1 下拉杆焊合件 Lower link weldment 2 4 300.56.109 环形螺钉 Spring 2 5 300.56.016 限位链后叉焊合件 Rear check chain 2 6 300.56.104 调节套管 Adjust sleeve 2 7 300.56.011 锁销组合件 Kock pin 2 8 300.56.015 限位链前叉焊合件 Front check chain 2 9 GB/T882-1986-14 55 销 14 55 Clevis pin with head 14 55 4 10 GB/T97.1-2002-14 垫圈 14 Plain washer 14 4 11 GB/T91-2000-4 25 开口销 4 25 Split pin 4 25 4 12 GB/T97.1-2002-16 垫圈 16 Plain washer 16 4 13 GB/T882-1986-B16 55 销轴 B16 55 Clevis pin with head B16 55 2 14 200.56.101-1 R 销 R-pin 2 15 300.56.029-1 左前限位链焊合件 Left-front check chain 1 16 300.56.024-1 提升杆下吊耳焊合件 Lower clevis of lift rod 2 17 JB/T7940.1-1995-M10 1 油杯 M10 1 Grease nipple M10 1 2 18 300.56.150 提升螺管 Lift rod upper clevis 2 19 GB/T6173-2000-M20 2 螺母 M20 2 Hex.nut M20 2 2 20 GB/T91-2000-3.2 26 销 3.2 26 Split pin 3.2 26 2 21 300.56.022-1 提升杆上吊耳焊合件 Lift rod up clevis 2 22 GB/T882-1986-16 80 销 16 80 Clevis pin with head 16 80 2 23 300.56.113 提升杆十字接头 Cross joint of lift rod 2 24 200.56.011 锁销组合件 Kock pin 2 25 300.56.026-1 右前限位链焊合件 Right-front check chain 1 116

27 悬挂装置总成 Suspension Mechanism 续表 26 200.56.103 下拉杆连接轴 Lower link shaft 1 27 300.56.018-1 上拉杆前调节杆总成 Upper link front adjusting rod 1 28 GB/T6170-2000-M24 六角螺母 M24 Hex.nut M24 1 29 280.56.016 调节螺管焊合件 Turn buckle of upper link 1 30 300.57.157 圆板 Round plate 1 31 GB/T93-1987-16 垫圈 16 Spring lock washer 16 2 32 GB/T6170-2000-M16 螺母 M16 Hex.nut M16 2 33 GB/T6172-2000-M24-L 螺母 M24( 左 ) Hex.nut M24-L 2 34 GB/T6172-2000-M22 螺母 M22 Hex.nut M22 2 35 GB/T6173-2000-M20 2-L 螺母 M20 2( 左 ) Hex.nut M20 2-L 2 36 300.56.012-1 上拉杆总成 Upper link assembly 1 37 300.56.013-1 提升杆总成 Lift rod assembly 2 38 300.56.033-1A 限位链总成 Check chain assembly 2 39 300.56.001-1 悬挂装置总成 Suspension mechanism assembly 1 117

118

28.1 液压提升管路系统总成 Hydraulic Lifting Pipeline Assembly 1 404G2-E.58.015 多路阀进油管焊合件 Inlet pipe weldment 1 2 GB/T5783-2000-M8 55 螺栓 M8 55 Hex. head bolt M8 55 2 3 GB/T93-1987-8 垫圈 8 Spring lock washer 8 15 4 404G2-6F.58.018 滤清器进油管焊合件 ( 一 ) Filter inlet pipe weldment(1) 1 5 GB/T5783-2000-M8 25 螺栓 M8 25 Hex. head bolt M8 25 4 6 404B.58D.120-1 固定夹 Fixed clip 4 7 GB/T6170-2000-M8 螺母 M8 Hex.nut M8 2 8 254-5.58.013 软管总成 Hose assy 1 9 404G2-6.58.015 滤清器进油管焊合件 ( 二 ) Filter inlet pipe weldment(2) 1 10 320.58.108 铰接螺栓 M22 1.5 Hollow bolt M22 1.5 2 11 JB-FT-CU-22 组合铜垫圈 22 Combination washer 22 4 12 YX0811A2-0000 液压油滤清器总成 Filter 1 13 404G2-6F.58.017-1 多路阀进油管前段焊合件 Front inlet pipe weldment 1 14 404B.58D.010 油泵吸油管焊合件 Inlet pipe assy of gear pump 1 15 GB/T5783-2000-M8 45 螺栓 M8 45 Hex. head bolt M8 45 3 16 GB/T5783-2000-M8 35 螺栓 M8 35 Hex. head bolt M8 35 3 17 CBN-F314B 齿轮泵 Gear pump 1 18 300.58.102 紧固螺栓 Fixup bolt 1 19 GB/T3452.1-1992-18 2.65 O 形圈 18 2.65 O-ring seal 18 2.65 2 20 GB/T5783-2000-M8 40 螺栓 M8 40 Hex. head bolt M8 40 3 21 GB/T97.1-2002-8 垫圈 8 Plain washer 8 2 22 404B.58.102 滤清器支架 Fix plank 1 23 GB/T97.1-2002-10 垫圈 10 Plain washer 10 2 24 GB/T93-1987-10 垫圈 10 Spring lock washer 10 2 25 GB/T5783-2000-M10 20 螺栓 M10 20 Hex. head bolt M10 20 2 119

28.1 液压提升管路系统总成 Hydraulic Lifting Pipeline Assembly 续表 26 JB/T8870-1999-2A(25-38) 喉箍 2A (25-38) Hoop 2A(25-38) 2 27 HG4-761-74-22 32 270 输油胶管 22 32 270 Hose 22 32 270 1 28 304.58A.101 纸垫 Paper gasket 1 29 JB-FT-CU-16 组合铜垫圈 16 Combination washer 16 2 30 JB/T6013-2000-M16 1.5 铰接螺栓 M16 1.5 Hollow bolt M16 1.5 1 31 404G2-E.58.016 多路阀回油管焊合件 Return pipe weldment 1 32 JB-FT-CU-14 组合铜垫圈 14 Combination washer 14 2 33 200.55.124 空心螺栓 Hollow bolt 1 34 GB/T5782-2000-M6 55 螺栓 M6 55 Hex. head bolt M6 55 3 35 254-1.61.101 多路阀吸油管接头 Linking tube 1 36 304G2-6.61.118 吸油管接头 Linking tube 2 37 354.61.101 铰接螺栓 Hollow bolt 7 38 354.61.102 垫圈 Spring lock washer 17 39 404G2-6F.58.027 多路阀出油管焊合件 ( 四 ) Outlet pipe weldment(4) 1 40 404G2-6F.58.025 多路阀出油管焊合件 ( 三 ) Outlet pipe weldment(3) 1 41 404G2-6F.58.023 多路阀出油管焊合件 ( 二 ) Outlet pipe weldment(2) 1 42 404G2-6F.58.021 多路阀出油管焊合件 ( 一 ) Outlet pipe weldment(1) 1 43 GB/T6173-2000-M24 2 螺母 M24 2 Hex.nut M24 2 8 44 ZD-10E-W/0-T/0-1 整体式多路阀 Multiple Directional Control Val 1 45 快换接头 NPT1/2" Quick change NPT1/2" 4 46 404G2-E.58.011 多路阀支架焊合件 Connecting plant weldment 1 47 GB/T93-1987-6 垫圈 6 Spring lock washer 6 3 48 GB/T6170-2000-M6 螺母 M6 Hex.nut M6 3 49 404G2-E.58.013 分配器进油管焊合件 Inlet pipe weldment 1 120

121

28.2 多路阀操纵总成 Multiple Directional Control Valve Operation Mechanism Ser. No. Part No. 名称及规格 Name & Specifications Quantity Remarks 1 504G3-3.51.041 固定轴焊合件 ( 一 ) Fixed axis(1) 1 2 504G3-3.51.161 尼龙隔圈 Nylon washer 3 3 504G3.55.218 衬套 (20*20) Sleeve(20 20) 2 4 404G2-E.58.023 左操纵杆焊合件 Left control rod weldment 1 5 404G2-E.58.024 右操纵杆焊合件 Right control rod weldment 1 6 504G3-3.51.231 操纵手柄 Control handle 2 7 504G3-3.51.040 固定板焊合件 ( 一 ) Fixed board(1) 1 8 504G3-3.51.107 密封垫 ( 四 ) Sealing gasket(4) 1 9.GB/T882-1986-B5 20 销轴 B5 20 Clevis pin with head B5 20 4 10 GB/T97.1-2002-5 垫圈 5 Plain washer 5 4 11 GB/T971-2000-2 16 销 2 16 Split pin 2 16 4 12 404G2-6D.58A.026 连接杆焊合件 Connecting rod 2 13 GB/T 6170-2000-M8 螺母 M8 Hex. nut M8 2 14 404G2-E.58.022 多路阀操纵杆焊合件 Manipulate lever weldment 2 15 504G3.55A.141 连接叉 Fork 2 16 GB/T 93-1987-8 垫圈 8 spring lock washer 8 2 17 GB/T 5783-2000-M8 25 螺栓 M8 25 Hex.head bolt M8 25 2 122

123

29 前配重总成 Front Balance Weight 1 250.73.101-1 配重 Balance weight block 6 2 GB/T6170-2000-M12 螺母 M12 Hex.nut M12 2 3 GB/T93-1987-12 垫圈 12 Spring lock washer 12 2 4 GB/T96-2002-12 垫圈 12 Plain washer 12 2 5 GB/T953-1988-M12 490 螺柱 M12 490 Clamping-type double stud M12 490 1 6 300-6.73.012 插销焊合件 Bolt weldment 1 7 GB/T6170-2000-M14 螺母 M14 Hex.nut M14 2 8 300.73.011 牵引板焊合件 Front drawbar weldment 1 9 GB/T5783-2000-M14 45 螺栓 M14 45 Hex.bolt M14 45 2 10 GB/T93-1987-14 垫圈 14 Spring lock washer 14 2 124

125

30 遮阳篷总成 Sunshade 1 254G3.45.101 遮阳篷 Sunshade 1 2 GB/T97.1-2002-12 垫圈 12 Plain washer 12 16 3 GB/T93-1987-12 垫圈 12 Spring lock washer 12 12 4 GB/T5783-2000-M12 25 螺栓 M12 25 Hex. head bolt M12 25 4 5 304-9A.45.011 上支撑架焊合件 Ascending shore 1 6 GB/T6170-2000-M10 螺母 M10 Hex. nut M10 2 7 GB/T93-1987-10 垫圈 10 Spring lock washer 10 4 8 GB/T97.1-2002-10 垫圈 10 Plain washer 10 4 9 GB/T5783-2000-M10 30 螺栓 M10 30 Hex. head bolt M10 30 4 10 304-9A.45.101 支撑钢管 Support tube 2 11 GB/T6170-2000-M12 螺母 M12 Hex. nut M12 8 12 GB/T5783-2000-M12 35 螺栓 M12 35 Hex. head bolt M12 35 8 13 304-9A.45.016 下支撑座焊合件 ( 左 ) Left shore 1 14 304-9A.45.102 固定板 Immobility board 2 15 GB/T6182-2000-M12 螺母 M12 Hex. nut M12 4 16 304-9A.45.103 U 型螺栓 U-bolt 4 17 304-9A.45.017 下支撑座焊合件 ( 右 ) Right shore 1 126

127

31 气缸盖罩总成 Cylinder Head Cover Assembly(Fig.1) 1 GB/T3452.1-2005-33.5 2.65 O 形圈 33.5 2.65 Seal ring 33.5 2.65 1 2 N85-01002 加油口盖 Oil filling cover 1 3 GB/T65-2000-M4 6 螺钉 M4 6 Bolt M4 6 4 4 ZN390TE-01018(H) EC 排放标签 EC Emission label 1 5 N85-01004 抽气管 Breather tube 1 6 4L68-01003B 气缸盖罩 Cylinder head cover 1 7 N485-01001 气缸盖罩密封圈 Cylinder head cover seal ring 1 8 N85-01005 挡架 Retainer 1 9 N85-01008 铁丝滤网 Steel wool screen 1 10 N85-01007 多孔挡板 Multi-hole retaining plate 1 11 N85-01006 挡油板 Oil retainer 1 12 GB/T859-1987-6 垫圈 6 Washer 6 2 13 GB/T65-2000-M6 12 螺钉 M6 12 Screw M6 12 2 14 ZN390TE-09007 回气管 Breather pipe 1 15 QC/T619-1999-Q676B25 夹箍 Q676B25 Pipe clip Q676B25 2 128

129

32 气缸盖总成 Cylinder Head Assembly(Fig.2) 1 N85-02101A 套管 Sleeve 4 2 GB/T5783-2000-M8 20 螺栓 M8 20 Bolt M8 20 4 3 N85-02004 吊耳 Lifting eye 2 4 N485Q-10002(H) 垫片 Gasket 1 5 N485-02109 碗形塞 Expansion plug Φ26 4 6 N85-02105 气门导管 Valve guide 4 7 GB/T923-88-M8 盖形螺母 M8 Nut M8 5 8 GB/T5783-2000-M10 30 螺栓 M10 30 Bolt M10 30 4 9 GB/T93-1987-10 垫圈 10 Washer 10 6 10 N85T-02001 排气管垫片 Exhaust manifold gasket 4 11 GB/T899-1988-M8 75 双头螺柱 M8 75 Stud M8 75 8 12 GB/T6170-2000-M8 螺母 M8 Nut M8 8 13 N485T-10001(E) 排气管 Exhaust manifold 1 14 4B26-021008 气缸盖 Cylinder head 1 15 4L68-020009 喷油器压板 Injector clamping plate 4 16 GB/T899-1988-M10 50 螺柱 M10 50 Stud M10 50 4 17 GB/T6170-2000-M10 螺母 M10 Nut M10 4 18 N85-02104 碗形塞 Expansion plug Φ55 1 19 N85-02102 碗形塞 Expansion plug Φ20 4 20 N485T-09001(F) 进气管 Intake manifold 1 21 GB/T5783-2000-M8 20 螺栓 M8 20 Bolt M8 20 4 22 GB/T97.1-2002-8 垫圈 8 Washer 8 4 23 N485-09006 垫片 Gasket 3 24 N485-09005 盖板 Cover 1 25 ZN490QA-02005 进气管垫片 Intake manifold gasket 1 130

32 气缸盖总成 Cylinder Head Assembly(Fig.2) 续表 26 4L68-021007 进气门座 Intake valve seat 4 27 4L68-021006 排气门座 Exhust valve seat 4 28 GB/T5783-2000-M8 16 螺栓 M8 16 Bolt M8 16 8 29 QJ/MD05.01-8 组合垫圈 8 Washer 8 5 30 GB/T899-88-M10 50 螺柱 M10 50 Bolt M10 50 8 31 GB/T859-87-8 垫圈 8 Washer 8 29 32 GB/T5783-2000-M8 28 螺栓 M8 28 Bolt M8 28 4 33 N85Q-17004 节温器壳垫片 Thermostat shell gasket 1 34 4B26-020027 电热塞闷头 Heater plug 4 35 N390T-09002(M) 进气接管 Intake joint pipe 1 36 N485Q-09100 空气加热器 Air heater 1 37 N485Q-09012(B) 安装板 Plate 1 38 ZN485T-09011 支架 Support 1 131

132

33 机体齿轮室总成 Cylinder Block and Gear Case Assembly(Fig.3) 1 GB/T5782-2000-M10 35 螺栓 M10 35 Bolt M10 35 10 2 GB/T5782-2000-M12 40 螺栓 M12 40 Bolt M12 40 4 3 GB/T859-1987-12 垫圈 12 Washer 12 2 4 GB/T859-1987-10 垫圈 10 Washer 10 12 5 ZN485T-03012 飞轮壳 Flywheel housing 1 6 GB/T9877-2008-DL85 110 12 油封 DL85 110 12 Oil seal DL85 110 12 1 7 GB/T5783-2000-M8 25 螺栓 M8 25 Bolt M8 25 7 8 GB/T859-1987-8 垫圈 8 Washer 8 46 9 GB/T848-1985-8 垫圈 8 Washer 8 42 10 N85-03108 塞片 Expansion plug 1 11 4L88-03109A 凸轮轴后衬套 Camshaft rear bushing 1 12 N85-03102 碗形塞 Expansion plugφ30 4 13 4L88-03112 凸轮轴衬套 Camshaft middle bushing 1 14 ZN490QA-03104 主轴承盖 Main shaft cover 4 15 N85-19005 推杆室盖垫片 Push-rod chamber cover gasket 1 16 ZN390TE-03025B 推杆室盖板 Push-rod chamber cover 1 17 CC490Q-030021 机油滤清器垫块 Longcylinder head bolt 1 18 4L68-031007 后主轴承盖 Rear main shaft cover 1 19 N90-03002 封水圈 Water seal ring 8 20 N85-03111 堵塞 Blocking plug 4 21 4L40-03101 机体 Cylinder block 1 22 4L88-031012(A) 凸轮轴衬套 Camshaft middle bushing 1 23 4L88-12001 齿轮室垫片 Gear case gasket 1 24 GB/T6170-2000-M8 螺母 M8 Nut M8 3 25 GB/T899-1988-M8 35 螺栓 M8 35 Bolt M8 35 3 133

33 机体齿轮室总成 Cylinder Block and Gear Case Assembly(Fig.3) 续表 26 ZN485T-12002 齿轮室 Gear case 1 27 GB/T6170-2000-M10 螺母 M10 Nut M10 1 28 GB/T93-1987-10 垫圈 10 Washer 10 1 29 N85T-12007A 发电机支架 Generator bracket 1 30 GB/T5782-2000-M8 20 螺栓 M8 20 Bolt M8 20 8 31 GB/T5782-2000-M10 90 螺栓 M10 90 Bolt M10 90 1 32 GB/T276-1982-6007 轴承 6007 Bearing 6007 2 33 4L88-12003(A) 齿轮室盖垫片 Gear case cover gasket 1 34 ZN485T-12004(A) 齿轮室盖 Gear case cover 1 35 GB/T5782-2000-M8 65 螺栓 M8 65 Bolt M8 65 4 36 GB/T5782-2000-M8 40 螺栓 M8 40 Bolt M8 40 1 37 GB/T5782-2000-M8 30 螺栓 M8 30 Bolt M8 30 2 38 N85T-12010 液压泵盖垫片 Hydraulic pump cover gasket 4 39 N85T-12009 液压泵盖 Hydraulic pump cover 2 40 GB/T5782-2000-M8 25 螺栓 M8 25 Bolt M8 25 11 41 GB/T9877-2008-DR52 72 12 油封 DR52 72 12 Oil seal DR52 72 12 1 42 N485T-12005 齿轮室前盖 Gear case front cover 1 43 N485T-12006 齿轮室前盖垫片 Gear case front cover gasket 1 44 N85-03014 气缸盖螺栓垫圈 Cylinder head bolt washer 14 45 N85-03016-2 气缸盖短螺栓 Short cylinder head bolt 4 46 N85-03015-2 气缸盖长螺栓 Long cylinder head bolt 14 47 4B26-030013 气缸盖垫片 Cylinder head gasket 2 48 N85-03017 气缸盖定位套 Cylinder head locating sleeve 2 49 ZN390TE-03003 气缸套 Cylinder liner 4 134

33 机体齿轮室总成 Cylinder Block and Gear Case Assembly(Fig.3) 续表 50 GB/T859-1987-6 垫圈 6 Washer 6 1 51 GB/T70-1985-M8 20 内六角圆柱头螺钉 M8 20 Inner hexagon cylindrical bolt M8 20 3 52 N85-03001 齿轮室定位套 Gear case locating sleeve 3 53 N85T-03110 定位销 Dowel pin 2 54 N85-03105 主轴承盖螺栓垫圈 Main shaft cover bolt washer 10 55 N90-03106 主轴承盖螺栓 Main shaft cover bolt 10 56 N85-03007 曲轴止推片 ( 下 ) Crankshaft thrust plate(lower) 2 57 N85-03009 曲轴止推片 ( 上 ) Crankshaft thrust plate(upper) 2 58 N85-03006 主轴瓦 ( 下 ) Main bearing shell(lower) 4 59 N85-03008 主轴瓦 ( 上 ) Main bearing shell(upper) 4 60 N85-03020 机油滤清器垫片 Lubricating oil filter gasket 1 61 N390T-03025 闷盖 Cap 1 62 ZN390TE-03200(A) 放水阀部件 Water draining cock 1 63 N85T-03005 后油封盖垫片 Rear oil seal cover gasket 1 64 N85T-03010 后油封盖 Rear oil seal cover 1 65 4L68-031014 凸轮轴中间衬套 Camshaft rear bushing 1 66 GB/T119.1-2000-B8 16 销 B8 16 Pin B8 16 2 67 GB/T119-2000-B10 25 销 B10 25 Pin B10 25 2 68 GB/T5782-2000-M8 60 螺栓 M8 60 Bolt M8 60 1 69 GB/T5782-2000-M8 45 螺栓 M8 45 Bolt M8 45 3 70 GB/T70-1985-M8 55 内六角圆柱头螺钉 M8 55 Inner hexagon cylindrical bolt M8 55 1 71 GB/T5782-2000-M8 50 螺栓 M8 50 Bolt M8 50 2 72 GB/T5782-2000-M8 75 螺栓 M8 75 Bolt M8 75 1 73 4L40-03022 加强板 Stiffiener 1 135

136

34 正时齿轮系总成 Timing Gear Train(Fig.4) 1 GB/T5782-2000-M12 30 螺栓 M12 30 Bolt M12 30 1 2 GB/T859-1987-12 垫圈 12 Washer 12 1 3 N85-04009 凸轮轴正时齿轮压板 Camshaft timing gear retainer 1 4 N85T-04011A-1 液压泵齿轮 Hydraulic pump gear 1 5 N85T-04007 凸轮轴正时齿轮 Camshaft timing gear 1 6 GB/T5782-2000-M8 16 螺栓 M8 16 Bolt M8 16 2 7 GB/T859-1987-8 垫圈 8 Washer 8 4 8 GB/T97.1-2002-8 垫圈 8 Washer 8 2 9 N85-04008 凸轮轴压板 Camshaft retainer 1 10 4L88-040002 正时惰齿轮衬套 Timing idle gear bushing 1 11 N85T-04004A 正时惰齿轮轴 Timing idle gear shaft 1 12 N85T-04012 空心螺栓 Hollow bolt 1 13 195-09001-1 垫圈 Washer 2 14 N85T-04100 喷油管部件 Oil pipe 1 15 GB/T5782-2000-M8 50 螺栓 M8 50 Bolt M8 50 2 16 N85T-04003 正时惰齿轮压板 Timing idle gear retainer 1 17 GB/T5783-2000-M6 25 螺栓 M6 25 Bolt M6 25 6 18 GB/T859-1987-6 垫圈 6 Washer 6 6 19 N485T-32001D 联接盘 Adapter 1 20 N85-04010 机油泵主动齿轮 Lubricating oil pump driving gear 1 21 N85-04006 曲轴正时齿轮 Crankshaft timing gear 1 22 4L88-040005 正时惰齿轮 Timing idle gear 1 23 N485T-04001A 燃油泵正时齿轮 Injection pump timing gear 1 137

138

35 活塞连杆总成 Piston and Connecting Rod Assembly(Fig.5) 1 4B26-05002 第一道活塞环 1st piston ring 4 2 4B26-05003 第二道活塞环 2nd piston ring 4 3 4B26-05100 油环部件 Oil ring 4 4 GB/T893.2-1986-28 挡圈 28 Circlip 28 8 5 4B26-05001 活塞 Piston 4 6 N85-05201 连杆 Connecting rod 4 7 N85-05203 连杆螺栓 Connecting rod bolt 8 8 4L68-050005 连杆轴瓦 Connecting rod bearing shell 8 9 N85-05204 连杆盖 Connecting rod cap 4 10 N85-05205 连杆螺母 Connecting rod nut 8 11 N85-05202 连杆衬套 Connecting rod bushing 4 12 N85-05004 活塞销 Piston pin 4 139

140

36 曲轴飞轮总成 Crankshaft and Flywheel Assembly(Fig.6) 1 N85Q-06007 曲轴皮带轮螺栓 Crankshaft pulley bolt 1 2 N85-06002 起动爪垫圈 Staring jaw washer 1 3 ZN485T-06001(A) 曲轴皮带轮 Crankshaft pulley 1 4 N485-04010(A) 机油泵主动齿轮 Lubricating oil pump driving gear 1 5 4L68-04006 曲轴正时齿轮 Crankshaft timing gear 1 6 GB/T1096-2003-C10 63 键 C10 63 Key C10 63 1 7 ZN490B-06004-1 曲轴 Crankshaft 1 8 GB/T119.1-2000-B10 25h8 销 B10 25h8 Cylindrical pin B10 25h8 1 9 N85-06102 飞轮齿圈 Flywheel ring gear 1 10 ZN485T-06101 飞轮 Flywheel 1 11 GB/T276-1994-6203-2LS 滚动轴承 6203-2LS Ball bearing 6203-2LS 1 12 N85-06005(A) 飞轮螺栓垫片 Flywheel blot washer 1 13 N390T-06006(B) 飞轮螺栓 Flywheel blot 6 141

142

37 配气机构 Valve Timing Mechanism(Fig.7) 1 N485-07001 凸轮轴 Camshaft 1 2 GB/T1096-2003-C10 25 平键 C10 25 Falt key C10 25 1 3 N485-07003 气门挺柱 Valve tappet 8 4 ZN485-07002 气门推杆 Valve push rod 8 5 N85-02208 堵塞 Blocking plug 2 6 N85-02201 前摇臂座 Front rocker arm support 1 7 GB/T859-1987-8 垫圈 8 Washer 8 10 8 GB/T5782-2000-M8 60 螺栓 M8 60 Bolt M8 60 5 9 GB/T70-1985-M8 45 螺钉 M8 45 Screw M8 45 5 10 N85-02212 气门摇臂衬套 Valve rocker arm bushing 8 11 N85-02203 气门间隙调整螺母 Valve clearance adjusting nut 8 12 N85-02202 气门间隙调整螺钉 Valve clearance adjusting screw 8 13 N85-02205 气门摇臂弹簧 Valve rocker arm spring 4 14 N85-02211 气门摇臂 Valve rocker arm 8 15 GB/T79-1985-M8 45 螺钉 M8 45 Screw M8 45 5 16 GB/T6170-2000-M8 螺母 M8 Nut M8 5 17 N85-022004 摇臂座 Rocker arm support 4 18 N85-02206 轴套 Rocker arm shaft bushing 3 19 N485-02207 摇臂轴 Rocker arm shaft 1 20 GB/T3452.1-2005 气门杆密封圈 Valve rod seal ring 8 21 N85-02001-1 气门弹簧上座 Valve spring seat(upper) 8 22 N85-02002 气门锁夹 Valve collet 16 23 N85-02003-1 气门外弹簧 Valve outer spring 8 24 N85-02003-2 气门内弹簧 Valve inner spring 8 25 4B26-02007 排气门 Exhaust valve 4 143

37 配气机构 Valve Timing Mechanism(Fig.7) 续表 26 4B26-02008 进气门 Intake valve 4 144

145

38 水泵风扇总成 Water Pump and Fan Assembly(Fig.8) 1 GB/T5783-2000-M8 60 螺栓 M8 60 Bolt M8 60 4 2 GB/T859-1987-8 垫圈 8 Washer 8 17 3 CC490Q-080012 冷却风扇 (φ380 吸风 ) Cooling fan (φ380 吸风 ) 1 4 N390T-08020(B) 风扇垫块组件 Fan pad 2 5 GB/T6170-2000-M10 螺母 M10 Nut M10 1 6 GB/T859-1987-10 垫圈 10 Washer 10 1 7 GB/T97.1-2002-10 垫圈 10 Washer 10 1 8 N390T-08011(A) 水泵皮带轮 Water pump pulley 1 9 N485T-08012 水泵皮带轮壳 Water pump pulley housing 1 10 GB/T5783-2000-M8 25 螺栓 M8 25 Bolt M8 25 1 11 GB/T97.1-2002-8 垫圈 8 Washer 8 1 12 GB/T1099-2003-4 36 键 4 36 Key 4 36 1 13 GB/T6170-2000-M8 螺母 M8 Nut M8 4 14 N390T-08018A 撑杆 Bracing 1 15 N85T-08004E 水泵壳体 Water pump housing 1 16 GB/T898-1976-M8 50 螺柱 M8 50 Stud M8 50 1 17 CZ475Q-170006 螺塞 Plug 1 18 N85Q-17003 节温器 t (Model 155B) Thermostat (Model 155B) 1 19 N390T-03025A 闷盖 Stifle 1 20 N85T-08008 节温器壳垫片 Thermostat housing gasket 1 21 N485Q-17001(S) 节温器盖 Thermostat cover 1 22 GB/T5783-2000-M8 30 螺栓 M8 30 Bolt M8 30 2 23 N85T-08003 水封 IF-12 Water seal ring IF-12 1 24 N85T-08005 水泵叶轮 Water pump impeller 1 25 N85T-08009 Water pump gasket Water pump gasket 1 146

38 水泵风扇总成 Water Pump and Fan Assembly(Fig.8) 续表 26 N85T-08010 水泵连接板 Water pump adapter 1 27 N85T-08017 水泵连接板垫片 Water pump adapter gasket 1 28 GB/T68-2000-M8 16 螺钉 M8 16 Screw M8 16 2 29 GB/T3452.1-2005- 40 3.1 O 形圈 40 3.1 Seal ring 40 3.1 1 30 GB/T5783-2000-M8 20 螺栓 M8 20 Bolt M8 20 2 31 N85T-08013 出水接头 Water drain connector 1 32 N85T-08014 出水接头垫片 Water drain connector gasket 1 33 GB/T5782-2000-M8 80 螺栓 M8 80 Bolt M8 80 2 34 N485T-08022 垫片 Gasket 1 35 N485T-08021 进水管 Water pipe 1 36 GB/T5780-2000-M8 45 螺栓 M8 45 Bolt M8 45 2 37 GB/T898-1988-M8 45 螺柱 M8 45 Stud M8 45 3 38 N85T-08006 水泵轴 Water pump shaft 1 39 GB/T276-1994-6007 滚动轴承 6007 Ball bearing 6007 2 40 N85T-08002 轴承隔套 Bearing spacing sleeve 1 41 GB/T893.2-1986-35 挡圈 35 Circlip 35 1 42 GB12732-2008-AV15 940 风扇皮带 AV15 940 Fan belt AV15 940 1 43 GB12732-2008-AV15 650 风扇皮带 AV15 650 Fan belt AV15 650 1 44 4L68-080013(A) 螺栓 Bolt 1 147

148

39 油底壳总成 Oil Sump Assembly (Fig.9) 1 N485T-03110 定位销 Dowel pin 2 2 ZN485T-11001 油底壳垫片 Oil sump gasket 1 3 ZN485T-11004 油底 Oil sump 1 4 GB/T93-1987-8 垫圈 8 Washer 8 46 5 GB/T5782-2000-M8 55 螺栓 M8 55 Bolt M8 55 1 6 GB/T3452.1-2005-11.2 2.65 O 形圈 11.2 2.65 O Seal ring 11.2 2.65 2 7 195-01026 闷头 Plug 2 8 ZN485T-11007 机油尺 Oil dipstick 1 9 CZ475Q-032200 机油尺管焊接件 Oil dipstick pipe body 1 10 QJ/MD05.01-12 组合垫圈 12 Washer 12 1 11 GB/T5783-2000-M8 30 螺栓 M8 30 Bolt M8 30 25 12 GB/T93-1987-10 垫圈 10 Washer 10 3 13 GB/T95-2002-10-100HV 垫圈 10-100HV Washer 10-100HV 3 14 GB/T5783-2000-M10 30 螺栓 M10 30 Bolt M10 30 3 15 ZN485T-11005B 副油底壳垫片 Auxiliary oil sump gasket 1 16 ZN485T-11006A 副油底壳 Auxiliary oil sump 1 17 GB/T5783-2000-M8 45 螺栓 M8 45 Bolt M8 45 8 18 GB/T5783-2000-M8 25 螺栓 M8 25 Bolt M8 25 11 149

150

40 机油泵总成 Lubricating Oil Pump Assembly (Fig.10) 1 GB/T6173-2000-M10 1 螺母 M10 1 Nut M10 1 1 2 GB/T859-1987-10 垫圈 10 Washer 10 1 3 GB/T848-1985-10 垫圈 10 Washer 10 1 4 N485Q-13007(C)-1 机油泵齿轮 Oil pump gear 1 5 N85-13006 限压阀塞 Pressure-limiting plug 1 6 GB/T5782-2000-M6 50 螺栓 M6 50 Bolt M6 50 3 7 GB/T5782-2000-M6 55 螺栓 M6 55 Bolt M6 55 1 8 GB/T859-1987-4 垫圈 4 Washer 4 4 9 N85-13005 限压弹簧 Pressure-limiting spring 1 10 GB/T859-1987-6 垫圈 6 Washer 6 4 11 GB/T308-2002-10 钢球 l0 Steel ball 10 1 12 N485-13001(A) 机油泵体 Oil pump body 1 13 N485-13004(A) 外转子 Outer rotor 1 14 N85-13103(A) 圆柱销 Cylindrical pin 1 15 N485-13102(A) 内转子 Inner rotor 1 16 N485-13008(A) 调整垫片 Adjusting shim 1 17 N85-13002(A) 机油泵盖 Oil pump cover 1 18 N85-13003 垫片 Gasket 1 19 GB/T1099-1979-3 5 13 键 3 5 13 Key3 5 13 1 20 N485-13101(A) 机油泵轴 Oil pump shaft 1 151

152

41 燃油系统总成 Fuel System (Fig.11) 1 4L40-18001 喷油泵 Injection pump 1 2 4L68-151000(D)-1 喷油器回油管接头部件 Injector fuel return pipe 1 3 GB/T1099.1-2007-3 16 半圆键 3 16 Woodruff 3 16 1 4 N85-18002(A) 喷油泵法兰垫片 Fuel pump flange gasket 1 5 4L68-18003 喷油泵垫块 Injection pump end cover 1 6 N85-18004 喷油泵联接盘垫片 Injection pump end gasket 1 7 4L68-150003 回油总管 Fuel return main pipe 1 8 N85-15500(M ) 输油泵进油管接头部件 Fuel feed pump inlet connection 1 9 N485-15300 滤清器出油管部件 Fuel filter outlet pipe 1 10 N485-15400B 输油泵出油管部件 Fuel feed pump outlet pipe 1 11 N485-28000B 柴油滤清器总成 Fuel filter 1 12 GB/T848-2002-8 垫圈 8 Washer 8 2 13 GB/T859-1987-8 垫圈 8 Washer 8 2 14 GB/T5782-2000-M8 25 螺栓 M8 25 Bolt M8 25 2 15 4L68-150001-3 喷油器回油套 Injector fuel return cover 1 16 4L68-150002 回油管 φ6 2 110 Fuel return pipe φ6 2 110 2 17 4L68-141000 第一缸高压油管部件 1 st cylinder high pressure fuel pipe 1 18 4L68-142000 第二缸高压油管部件 2 nd cylinder high pressure fuel pipe 1 19 4L68-143000 第三缸高压油管部件 3 rd cylinder high pressure fuel pipe 1 20 4B26-144000 第四缸高压油管部件 4 th cylinder high pressure fuel pipe 1 21 4L40-25000Z 喷油器总成 Injector 4 153

154

42 机油集滤器总成 Oil Suction Strainer Assembly (Fig.12) 1 4L88-16002 垫片 Gasket 1 2 4L88-16000A 机油集滤器总成 Oil suction strainer 1 3 GB/T859-1987-8 垫圈 8 Washer 8 3 4 GB/T5782-2000- M8 40 螺栓 M8 40 Bolt M8 40 2 5 GB/T5783-2000- M8 25 螺栓 M8 25 Bolt M8 25 1 155

156

43 张紧轮部件 Tension pulley assembly (Fig.13) 1 N390T-21002 张紧轮支架 Tension pulley bracket 1 2 N390T-21004 张紧轮轴 Tension pulley shaft 1 3 N390T-21003 套圈 Bush ring 2 4 N390T-21001 张紧轮 Tension pulley 1 5 GB/T276-1994-6302E-2RS 轴承 6302E-2RS Bearing 6302E-2RS 1 6 GB/T893.1-1986-42 挡圈 42 Thrust ring 42 1 7 GB/T93-1987-12 垫圈 12 Washer 12 1 8 GB/T6170-2000-M12 螺母 M12 Nut M12 1 9 GB/T97.1-1985-8 垫圈 8 Washer 8 2 10 GB/T/T93-1987-8 垫圈 8 Washer 8 2 11 GB/T5783-2000-M8 20 螺栓 M8 20 Bolt M8 20 2 157

158

44 机滤发电机起动电机 Oil Filter/Air Filter/Generator/Starting Motor/Silencer(Fig.14) 1 N485Q-26000(B) 机油滤清器总成 Lubricating oil filter 1 2 N485Q-30000(H) 起动电机总成 Starting motor 1 3 N390T-29200B 发电机防护罩焊接件 Dynamo shield 1 4 N85Q-29000 充电发电机总成 Charging generator 1 159