YANMAR (RAL) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION 1 122117-01970 橡胶垫片 RUBBER PACKING COOLING WATER SPLICER 2 123210-09310 垫片 PACKING 3 130390-53312 进口接头组 FUEL FILTER CASING COMP. 4 132310-09150 卡环 N/A C-CIRCLIP N/A 5 132310-09301 ANTI-CORROSIVE ZINC ANTI-CORROSIVE ZINC 6 132310-09330 垫片 GASKET 7 132310-15020 垫片 25 GASKET 25 8 132310-72030 启动空气弹簧 N/A STARTING AIR SPRING N/A 9 132310-72060 冷却阀柱塞 N/A VALVE COOLING PLUNGER N/A 10 132310-91300 温度计 COOLING WATER 11 132310-91311 温度计 EXHAUST THERMOMETER 12 132500-42290 叶轮螺母 NUT FOR IMPELLER 13 132500-42300 垫片 WASHER 14 133604-02090 推力轴承 Thrust Bearing 15 135602-11750 阀杆密封 VALVE STEM SEAL 16 136600-01202 SET BOLT, CYL..HEAD SET BOLT, CYL..HEAD 17 136600-01220 NUT CYL.HEAD SET BOLT NUT CYL.HEAD SET BOLT 18 136600-01300 缸套 O- 型圈 CYLINDER LINER O-RING 19 136600-01310 缸套垫片 GASKET 20 136600-01340 缸盖垫片 1.0 GASKET,CYLINDER HEAD 1.0 21 136600-01350 缸盖垫片 1.0 GASKET CYLINDER HEAD1.0 22 136600-01361 气缸套上部密封垫片 PACKING 23 136600-01370 缸盖垫片 D213 d198.5 t0.3 PACKING CYLINDER HEAD D213 d198.5 t0.3 24 136600-01371 缸盖垫片 T1.4 GASKET FOR CYLINDER HEAD T1.4 25 136600-01411 导门垫片 PACKING 26 136600-01470 垫片 PACKING 27 136600-01511 垫片 PACKING 28 136600-01530 垫片 PACKING 29 136600-01730 CYL.SIDE COVER COMP. W/FEED PORT CYL.SIDE COVER COMP. W/FEED PORT 30 136600-01842 衬套 OIL SHIELD BUSH,UPPER & LOWER 31 136600-01860 缸套 CYL.LINER ASSY 32 136600-01870 垫片 PACKING 33 136600-01970 O- 型圈 O-RING 34 136600-02100 主轴瓦 ( 后 ) MAIN BEARING(REAR) 35 136600-02120 主轴瓦 MAIN BEARING SHELL
36 136600-02150 主轴瓦加厚 0.5mm MAIN BEARING(M)- U/S0.50W/MARKING 37 136600-02180 主轴瓦 U/S1.00 MAIN BEARING SHELL U/S1.00 38 136600-02451 BUSH, INNER(D07/d75/L53) BUSH, INNER(D07/d75/L53) 39 136600-02461 BUSH,FLYWHEEL SIDE (D90/d75/L53) BUSH,FLYWHEEL SIDE (D90/d75/L53) 40 136600-02470 LOCKING LOCKING 41 136600-09251 CONNECTOR, CONNECTOR, C.W.(D21/L46) C.W.(D21/L46) 42 136600-09261 CONNECTOR, CONNECTOR, C.W.(D15/L46) C.W.(D15/L46) 43 136600-09272 CONNECTOR, CONNECTOR, C.W.(D21/L31) C.W.(D21/L31) 44 136600-09280 O- 型圈 D23 d14 O-RING D23 d14 45 136600-09340 垫圈 PACKING, CYL.-BED PLATE MATCHING FACE 46 136600-11090 阀座 VALVE SEAT 47 136600-11100 气阀 VALVE 48 136600-11110 排气阀 EX-VALVE 49 136600-11120 弹簧 SPRING(A) SUCT/EXH.VALVE 50 136600-11130 弹簧 SPRING(B) SUCT/EXH.VALVE 51 136600-11161 进气导管 INTAKE VALVE GUIDE 52 136600-11170 排气导管 EXHAUST VALVE GUIDE 53 136600-11171 V/V GUIDE EXHAUST V/V GUIDE EXHAUST 54 136600-11180 RETAINER V/V SPRING RETAINER V/V SPRING 55 136600-11191 气门铨 COTTER 56 136600-11220 摇臂衬套 ROCK ARM BUSH 57 136600-11230 调节螺栓 ADJUST SCREW 58 136600-11240 锁母 NUT VALVE LOCKER ARM ADJUST SCREW 59 136600-11251 摇臂轴 SHAFT ROCKER ARM 60 136600-11261 SHAFT SUPPORT, VALVE ROCKER ARM SHAFT SUPPORT, VALVE ROCKER ARM 61 136600-11262 摇臂支撑架 SHAFT SUPPORT ROCKER ARM 62 136600-11270 垫片 PACKING 63 136600-11320 螺栓 Stud Bolt 64 136600-11331 SUCTION V/V ROCKER ARM W/BUSH 65 136600-11341 EXH.V/V ROCKER ARM W/BUSH SUCTION V/V ROCKER ARM W/BUSH EXH.V/V ROCKER ARM W/BUSH 66 136600-11400 RETAINER RETAINER 67 136600-11480 密封圈 PACKING 68 136600-11534 预燃室 ( 头部 ) PRE-BURNING ROOM 69 136600-11580 密封 SEAL,SUCTION V/V STEM
70 136600-11581 油封 外骨架 VALVE STEM SEAL 16 71 136600-11630 阀座 (O/S 0.5) SEAT VALVE O/S 0.5 72 136600-11630-RAL- 阀座 VALVE SEAT(2MM US) VALVE SEAT-U/S 2.0 73 136600-11640 阀座 SEAT VALVE STD 74 136600-11750 ANTI-CORROSIVE ZINC ANTI-CORROSIVE ZINC 75 136600-11760 ANTICORROSIVE ZING ANTICORROSIVE ZING 76 136600-11871 螺栓 Stud Bolt 77 136600-11900 燃油喷射阀导套 Valve Guard Fuel Injection Valve 78 136600-11980 密封圈 PACKING 79 136600-11990 密封圈 PACKING 80 136600-12201 进气管垫片 GASKET 81 136600-1230 防松螺栓 LOCKING BOLT (A) 82 136600-1250 螺母 NUT 83 136600-13210 排气管垫片 GASKET,EXHAUST PIPE 84 136600-13220 垫圈 GASKET 85 136600-14140 COUPLING PIECE COUPLING PIECE 86 136600-14400 挺杆 VALVE PUSH ROD 87 136600-14480 PUSH ROD COMPLETE PUSH ROD COMPLETE 88 136600-14481 阀推杆 VALVE PUSH ROD 89 136600-14520 垫片 PACKING 90 136600-14570 挺杆总成 TAPPET COMPLETE 91 136600-22250 活塞环 PISTON RING 92 136600-22260 活塞环 PISTON RING 93 136600-22270 活塞环 PISTON RING 94 136600-23121 LOCKING LOCKING 95 136600-23200 连杆螺栓 BIG END BOLT 96 136600-23220 螺母 NUT 97 136600-23230 开口销 SPLIT PIN 4X40 98 136600-23320 连杆瓦 U/S1.00 CRANK PIN METAL U/S1.00 99 136600-23350 止动环 LIMITING RING 100 136600-34072 调节螺钉 M16 D21 L95 ADJUST SCREW M16 D21 L95 101 136600-34200 阀弹簧 (D-23.5,L-100) VALVE SPRING (D-23.5,L-100) 102 136600-34201 阀弹簧 (D-23.5,L-100) VALVE SPRING (D-23.5,L-100) 103 136600-350352 螺栓 7/16x35 BOLT 7/16x35 104 136600-35540 滑油滤器 LUB OIL STRAINER 105 136600-39430 摇臂调节螺钉 ADJUSTING SCREW FOR ROCKER ARM 106 136600-42231 叶轮 IMPELLER 107 136600-42241 自带淡水泵轴封 ( 填料箱 ) MECHANIC SEAL FOR C.W.PUMP 108 136600-42480 油封 30X45X8 OIL SEAL 30X45X8 109 136600-48230 垫片 PACKING 110 136600-51250 柱塞总成 PLUNGER ASSY 111 136600-51271 柱塞偶件 PLUNGER
112 136600-51300 出油阀总成 DELIVERY VALVE 113 136600-51310 出油阀弹簧 DELIVERY VALVE SPRING 114 136600-51320 出油阀垫片 Gasket Delivery Valve 115 136600-51330 柱塞弹簧 Spring Barrel. 116 136600-53000 喷油嘴 NOZZLE 117 136600-53001 喷油嘴 NOZZLE 118 136600-53080 VALVE CASE VALVE CASE 119 136600-53090 垫片 GASKET 14.5/21.4 T2 120 136600-53120 弹簧 INJECTOR SPRING 121 136600-53130 弹簧脚 Spring Shoe 122 136600-53150 喷油器调节垫 ADJUSTING GASKET FOR NOZZLE HOLD 123 136600-53190 帽 Cap Body 124 136600-53200 填料 Packing 125 136600-53470 INTER-SPINDLE INTER-SPINDLE 126 136600-54440 调节片总成 ADJUST PLATE COMPL. 127 136600-54570 骨架油封 OIL SEAL 128 136600-54670 铰刀螺栓 REAMER BOLT 129 136600-59810 电机高压油管 F.O.PIPE 130 136600-59820 电机高压油管 F.O.PIPE 131 136600-59830 电机高压油管 F.O.PIPE 132 136600-59840 电机高压油管 F.O. PIPE 133 136600-59850 电机高压油管 F.O.PIPE 134 136600-59860 电机高压油管 F.O.PIPE 135 136600-64530 轴承 BEARING 136 136600-66901 蜗杆轴, 右手螺纹 WORM SHAFT,RIGHT HAND SCREW 137 136600-71101 启动阀盖 ( 上 ) Starting Valve Upper Cover 138 136600-71120 弹簧 SPRING 139 136600-71140 启动空气管 Starting Air Pipe. 140 136600-72020 空气启动阀 N/A STARTING AIR VALVE N/A 141 136600-72100 阀座 N/A VALVE SEAT N/A 142 136600-72110 垫片 N/A BUSH N/A 143 136602-11100 进气阀 SUCTION VALVE 144 136602-11110 排气阀 EXHAUST VALVE 145 136603-59610 高压油管 (NO1) F.O.INJECTION PIPE NO.1 146 136603-59620 高压油管 (NO2) F.O.INJECTION PIPE NO.2 147 136603-59630 高压油管 (NO3) F.O.INJECTION PIPE NO.3 148 136603-59640 高压油管 (NO4) F.O.INJECTION PIPE NO.4 149 136603-59650 高压油管 (NO5) F.O.INJECTION PIPE NO.5 150 136603-59660 高压油管 (NO6) F.O.INJECTION PIPE NO.6 151 136604-02070 主轴瓦 ( 后端 ) 加厚 0.5mm MAIN BEARING(F)- U/S0.50W/MARKING 152 136604-02090 推力瓦 THRUST BEARING
153 136604-02100 主轴瓦 ( 后 ) THRUST BEARING 154 136604-02101 主轴瓦 ( 后 ) THIN KELMET METAL 155 136604-02120 主轴瓦 MAIN BEARING SHELL 156 157 136604-02121 136604-02131 主轴瓦主轴瓦 ( 中端 ) MAIN BEARING METAL ASSLY MAIN BEARING(M)- U/S0.25W/MARKING 158 136604-02211 主轴瓦 ( 后端 ) MAIN BEARING(F)- U/S0.25W/MARKING 159 136604-22070 活塞 RAL-HT PISTON 160 136604-22071 活塞总成 PISTON COMP. 161 136604-22200 活塞销 PISTON PIN 162 136604-22200-OIL RINGS 油环 OIL RING 163 136604-22222 活塞环 PISTON RING #3 164 136604-22232 活塞环 PISTON RING #2,4 165 136604-22300 活塞销 RAL PISTON PIN RAL 166 136604-22410 涨油环 OIL RING (COIL) 167 136604-22550 活塞环 PISTON RING #1 168 136604-23022 连杆 RAL-T N/A CONNECTING ROD RAL-T N/A 169 136604-23300 连杆轴瓦 CRANK PIN SHELL 170 136604-23310 轴承 (0.25) Bottom End Bearing (0.25) 171 136604-23320 轴承 (0.50) Bottom End Bearing (0.50) 172 136604-23851 连杆轴瓦 CRANK PIN SHELL 173 136604-23871 连杆瓦 CRANKPIN BEARING U/S0.25 174 136604-23881 连杆瓦加厚 0.5mm CRANKPIN BEARING U/S0.50 175 136605-13221 膨胀接头 EXPANSION JOINT 176 136605-13230 膨胀接头 EXPANSION JOINT 177 136605-22072 活塞环组 PISTON RIGN SET 178 136605-91311 温度计 550C L370 PF3/8 THERMOMETER 550C L370 PF3/8 179 136605-91312 温度计 550C L370 PF3/8 THERMOMETER 550C L370 PF3/8 180 136605-91313 温度计 THERMOMETER FOR EXH.GAS 181 136616-11031 缸盖 RAL-T CYLINDER HEAD RAL-T 182 136686-23121 锁紧垫圈 LOCK WASHER 183 137600-09280 橡胶衬垫 D-23.0 D-14.0 RUBBER PACKING D-23.0 D-14.0 184 137600-14700 空气分配器连接块 JOINT FOR S.A.ROTATOR 185 137600-15141 垫片 GASKET 186 137600-15170 手轮 HANDLE 187 137600-33170 填料 Packing 188 137600-35580 垫片 WASHER 34/54.5X1.0 189 137600-42060 水封环 90 RING FOR IMPELLER 90 190 137600-55721 燃油滤芯 FO ELEMENT FILTER 191 137600-72410 分配器转阀 DISTRIBUTING VALVE 192 137600-72430 分配器盖垫片 PACKING COVER 193 137602-18160 垫片 GASKET
194 137602-18610 增压机排气阀垫片 PACKING OUTLET CONNECTING PIPE 195 137610-32651 套 BUSH 196 137610-42380 止动垫片 35 LOCK WASHER 35 197 137610-42460 挡水圈 COLLAR WATER SHIELD 198 137610-42480 油封 OIL SEAL TC355511 199 137610-42490 机械密封 MECHANICAL SEAL 200 138613-91302 温度计 200CX3/8 THERMOMETER 200CX3/8 201 138613-91330 温度计 THERMOMETER 500CX1/2X160 202 138623-11350 承碟 RETAINER 203 204 139653-18241 139653-18261 胶管 D128Xd112XL72 护套 D133.2 d128 W13 RUBBER HOSE D128Xd112XL72 COVER RUBBER HOSE D133.2 d128 W13 205 139653-18540 排气管垫片 GASKET,EXHAUST PIPE 206 141646-52670 油封 OIL SEAL 207 144626-51751 高压油泵调节垫 ADJUSTING GASKET FOR H.P.OIL PUMP 208 21151-030162 螺栓 BOLTS 209 21151-030202 六角螺栓 HEXAGONAL BOLT 3/8' X20 210 21151-030252 六角螺栓 HEXAGONAL BOLT 3/8' X25 211 21151-040352 螺栓 1/2X35 BOLT 1/2X35 212 21151-350202 六角螺栓 HEXAGONAL BOLT 7/16' X30 213 21151-350302 六角螺栓 HEXAGONAL BOLT 7/16' X32 214 21153-350302 排气管螺栓 (7/16x30) BOLT EXH MANIFOLD(7/16x30) 215 21157-040202 螺栓 1/2X22 BOLT 1/2X22 216 21157-040352 螺栓 W1/2X35 BOLT W1/2X35 217 21157-350302 进气管螺栓 (7/16x30) BOLT INLET MANIFOLD(7/16x30) 218 21157-350322 BOLT STARTING BOLT STARTING PIPE(7/16x30) PIPE(7/16x30) 219 21317-030002 螺母 NUT 220 21317-030652 螺栓 Stud Bolt 221 21731-030002 螺母 3/8 NUT W3/8 222 21731-040002 螺母 HEXAGONAL NUT 1/2' 223 21737-030002 螺母 Nut 224 21737-040002 螺母 1/2 NUT 1/2 225 21737-050001 螺母 Nut 226 22131-140000 平垫 14 WASHER 14 227 22151-030652 双头螺栓 3/8X65 STUD 3/8X65 228 22212-040000 弹簧挡圈 4 SPRING WASHER 4 229 22212-080000 弹簧垫圈 8 SPRING WASHER 8 230 22212-090000 弹簧垫圈 SPRING WASHER 231 22242-000200 挡圈 C-CIRCLIP 232 222420-00220 CIRCLIP ROCKER ARM CIRCLIP ROCKER ARM 233 22242-000322 摇臂轴簧环 CIRCLIP,ROCKER ARM SHAFT
234 22340-100222 圆柱销 10X22 PARALLEL PIN 10X22 235 22411-400350 开口销 4X35 SPLIIT PIN 4X35 236 22411-400400 开口销 SPLIT PIN 4X40 237 22411-500450 开口销 5X45 COTTER PIN 238 22451-200000 钢丝 WIRE,2.0X300 239 22512-070200 键 7X20 KEY 7X20 240 22512-070220 键 7X22 FEATHER KEY 7X22 241 22512-070320 轴键 7X32 KEY 7X32 242 23334-200000 UNION UNION 243 23351-080000 管接头螺栓 PIPE JOINT BOLT 244 23354-080000 管接头螺栓 PIPE JOINT BOLT 245 23413-200000 示功阀铜垫 GASKET 246 23414-060000 垫片 6 GASKET 6 247 23414-110000 垫片 11 GASKET 11 248 23414-120000 铜垫片 PACKING 12X1 249 23414-130000 垫片 13 GASKET 13 250 23414-140000 垫片 14 GASKET 14 251 23414-160000 垫片 PACKING 252 23414-170000 垫片 17 GASKET 17 253 23414-180000 垫片 PACKING 254 23414-200000 垫片 HOUSING PACKING 255 23414-210000 垫片 GASKET 21 256 23414-220000 垫片 22 GASKET 22 257 23414-250000 垫片 25 GASKET 25 258 23414-260000 垫片 26X1 GASKET 26X1 259 23414-270000 垫片 27 GASKET 27 260 23414-300000 垫片 GASKET 261 23418-100000 垫片 10 NYLON PACKING 10 262 23851-060000 球接头螺栓 BALL JOINT BOLT 263 23851-150000 铰接螺栓 PIPE JOINT BOLT 264 23883-140002 螺塞 M14 PLUG M14 265 23894-030002 六角螺塞 3/8 HEX,PLUG 3/8 266 23897-030002 螺塞 PF3/8 PLUG PF3/8 267 24101-060014 轴承 6001 BEARING 6001 268 24101-060034 轴承 (6003) BEARING(6003) 269 24101-063054 轴承 BEARING 6305 270 24102-062054 轴承 6205U BEARING 6205U 271 24102-062074 轴承 BEARING 6207 272 24311-000070 O- 型圈 P10 O-RING P10 273 24311-000180 O- 型圈 O-RING 274 24311-000220 O- 型圈 O-RING 275 24311-000290 O- 型圈 P28 O-RING P28 276 24311-000400 O- 形圈 G40 O-RING G40 277 24321-000400 O- 形圈 G40 O-RING G40
278 24321-000450 O- 型圈 O-RING 279 24321-000700 O- 型圈 O-RING 280 24321-001350 滑油泵密封圈 SEAL RING 281 26111-080322 螺栓 BOLT M8 1.25X30 282 26711-100002 螺母 NUT 10x1.5 283 26711-120002 螺母 NUT 284 26717-040002 螺母 NUT M4 285 26717-120002 螺母 M12 NUT M12 286 26717-160002 螺母 M16X2.0 NUT(3) M16X2.0 287 26751-080002 螺母 (3)8X1.25 NUT (3)M8x1.25 288 26751-100002 螺母 NUT 10x1.5 289 26751-120002 螺母 NUT M12X1.75 290 26751-180002 螺母 M18X2.5 NUT M18X2.5 291 26777-160002 锁母 M16X1.5 LOCK M16X1.5 292 26911-040062 顶丝 M4X0.7X5 SET SCREW M4X0.7X5 293 26914-040062 定位螺钉 M4X6 LOCK SCREW M4X6 294 26914-050082 螺钉 SCREW 295 28521-030300 温度计 100C L158 PF3/8 THERMOMETER 100C L158 PF3/8 296 28521-030309 温度表 0-100C THERMOMETER 0-100C 297 28521-040300 温度计 L.O.THERMOMETER 298 299 300 301 302 303 28551-030300 285510-30300 28571-500110 285715-00110 28573-620050 285736-20050 温度计 100C L158 PF3/8 温度计 100DEG,L158,PF 3/8 温度计 600CX1/2X160 温度计 620DEG,L290,PF1/2 温度计 620C L200 PF3/8 温度计 620DEG L200 PF3/8 THERMOMETER 100C L158 PF3/8 THERMOMETERS 100DEG,L158,PF 3/8 THERMOMETER 600CX1/2X160 THERMOMETERS 620DEG,L290,PF1/2 THERMOMETER 620C L200 PF3/8 THERMOMETERS 620DEG L200 PF3/8 304 286111-71200 转速表 TECHOMETER 305 28711-000800 转速表软轴 FLEX. CABLE, L=800 306 43121-100210 膨胀接头 430X380 EXPANSION JOINT 430X380 307 43416-000232 垫片 PACKING 308 43416-047570 垫片 PACKING 309 43811-006060 翼式泵 WING PUMP 310 44100-002621 止回阀 CHECK VALVE 311 44100-002621 止回阀 CHECK VALVE 312 44111-000020 止回阀 AIR CHECK VALVE 313 44111-000020 止回阀 AIR CHECK VALVE 314 6RAL-01850 缸套 CYLINDER LINER 315 6RAL-CYL HEAD 缸盖垫片,T=1.5MM CYL HEAD GASKET T=1.5MM GASKET 1.5 316 736600-01850 缸套 CYLINDER LINER 317 736600-11651 进气摇臂 ROCKER ARM ASSY SUC
318 736600-11661 摇臂 ROCKER ARM 319 736600-11700 缸盖总成 CYLINDER HEAD ASSY 320 736600-15550 指示阀 INDICATOR VALVE 321 736600-22500 活塞环组 PISTON RIGN SET 322 736600-71152 缸头启动阀总成 SAFETY & INDICATOR ASSY 323 736602-91310 排气温度计 EXH THERMOMETER 324 736606-32701 燃油泵总成 LUBE OIL PUMP ASS'Y 325 736610-53350 燃油喷射阀 Fuel Injection Valve. 326 327 328 329 330 331 332 HEAD O-RING RAL-HT- L.O.PRES.REGULATING VALVE ASSY Head O-Ring L.O.PRES.REGULATING VALVE ASSY 350 136600-11980 密封圈 PACKING 351 136600-11990 密封圈 PACKING Head O-Ring L.O.PRES.REGULATING VALVE ASSY RAL-MAIN BEARING(F)- 主轴瓦加厚 0.2 MAIN BEARING(F)-U/S 0.20W U/S 0.20W IMARKING IMARKING RAL-MAIN BEARING(F)- 主轴瓦加厚 0.3 MAIN BEARING(F)-U/S 0.30W U/S 0.30W MARKING MARKING 122117-01970 橡胶垫片 RUBBER PACKING COOLING WATER SPLICER 135210-51330 135210-51351 排气阀弹簧垫片 SPRING,DELIVERY VALVE PACKING,DELIVERY VALVE HOLDER 333 13602-133310 EXPENSION JOINT EXPENSION JOINT 334 136600-01180 缸套 RAL CYLINDER LINER 335 136600-01340 缸盖垫片 1.0 GASKET,CYLINDER HEAD 1.0 336 136600-01970 O- 型圈 O-RING 337 136600-02120 主轴瓦 MAIN BEARING SHELL 338 136600-02180 主轴瓦 U/S1.00 MAIN BEARING SHELL U/S1.00 339 136600-09280 O- 型圈 D23 d14 O-RING D23 d14 340 136600-11251 摇臂轴 SHAFT ROCKER ARM 341 342 136600-11262 136600-11271 摇臂支撑架 VALVE ARM LOCKER SHAFT SUPPORT ROCKER ARM VALVE ARM LOCKER ARM 343 136600-11370 ARM SHAFT 接触片 SHAFT CONTACT PIECE VALVE ROCKER ARM 344 136600-11480 密封圈 PACKING 345 136600-11580 密封 SEAL,SUCTION V/V STEM 346 347 136600-11581 136600-11600 油封 外骨架橡胶垫圈阀帽 VALVE STEM SEAL 16 RUBBER PACKING BONNET (267X264) 348 349 136600-11760 136600-11910 防腐锌块大头螺钉 ANTICORROSIVE ZING STUD BOLT(PRECOMBRETION CHAMBER)(W14 L63)
352 353 136600-22250 136600-23101 活塞环连杆小端衬套 PISTON RING BUSH,CONNECTING ROD SMALL END 354 136600-42480 油封 30X45X8 OIL SEAL 30X45X8 355 136600-42502 淡水泵机械轴封 MECHANICAL SEAL 356 136600-53001 喷油嘴 NOZZLE 357 136600-53090 垫片 GASKET 14.5/21.4 T2 358 136600-53200 填料 Packing 359 136600-54570 骨架油封 OIL SEAL 360 136603-59610 高压油管 (NO1) F.O.INJECTION PIPE NO.1 361 136603-59620 高压油管 (NO2) F.O.INJECTION PIPE NO.2 362 136603-59630 高压油管 (NO3) F.O.INJECTION PIPE NO.3 363 136603-59640 高压油管 (NO4) F.O.INJECTION PIPE NO.4 364 136603-59650 高压油管 (NO5) F.O.INJECTION PIPE NO.5 365 136603-59660 高压油管 (NO6) F.O.INJECTION PIPE NO.6 366 136604-02090 推力瓦 THRUST BEARING 367 136604-22300 活塞销 RAL PISTON PIN RAL 368 136604-22410 涨油环 OIL RING (COIL) 369 136604-23851 连杆轴瓦 CRANK PIN SHELL 370 136605-13220 EXPENSION JOINT 1-3 EXPENSION JOINT 1-3 CYL CYL 371 136605-22072 活塞环组 PISTON RIGN SET 372 137600-14220 梃柱滚柱 TAPPET ROLLER 373 137610-42492 机械密封 MECHANICAL SEAL 374 139653-18540 排气管垫片 GASKET,EXHAUST PIPE 375 144626-51050 锥形滚柱轴承 TAPER ROLLER BEARING #32206 376 144626-51360 O 型圈 O RING,DELIVERY VALVE 377 144626-51420 O 型圈 O RING,BARREL SUPPORT 378 144626-51540 挡圈 CIRCLIP 379 144626-51840 O 型圈 O RING,SUPPORT A 380 145613-51360 排气阀塞 STOPPER,DISCHARGE VALVE 381 22252-000700 弹性挡圈 CIRCLIP FOR HOLE 382 23414-110000 垫片 11 GASKET 11 383 24311-000290 O- 型圈 P28 O-RING P28 384 24311-000400 O- 形圈 G40 O-RING G40 385 24311-350220 O- 型圈 O-RING 386 24314-000120 O- 型圈 P12 O-RING P12 387 24321-000450 O- 型圈 O-RING 388 6RAL-Exh gas thermometer 排气温度计 EXH GAS THERMOMETER REFILL refill 600deg 600DEG 389 6RAL-Jacket cooling 水套冷却温度计 JACKET COOLING thermometer 0-100deg aps THERMOMETER 0-100DEG APS 390 736600-11661 摇臂 ROCKER ARM 391 736600-22500 活塞环组 PISTON RIGN SET
392 736600-53200 燃油喷射阀 (INCLUDED PARTS ITEMS 1TO20) FUEL INJECTION VALVE(INCLUDED PARTS ITEMS 1TO20) 393 736600-53360 高压喷射阀总成 F.O.INJECTION VALVE ASSY 394 C39600-59030 F.O.INJ PIPE INCK21- F.O.INJ PIPE INCK21-22(H.P) 22(H.P) 395 RL-HT-CYLINDER HEAD 缸盖 CYLINDER HEAD CATALOGUE