Microsoft Word - T170S-5RB004N-0A18R0-200FH_970506V63_

Size: px

Start display at page:

Download "Microsoft Word - T170S-5RB004N-0A18R0-200FH_970506V63_"

婴吕
7 years ago
Views:

1 萬達光電科技股份有限公司 PRODUCT SPECIFICATIONS 產品規範書 Customer ( 客戶 ): Model ( 型式 ): T170S-5RB004N-0A18R0-200FH Mode ( 種類 ): Five-wire Analog Touch Panel Date ( 日期 ): May 06, 2008 Version ( 版本 ): 6.3 Customer Approval 客戶簽認 HIGGSTEC INCORPORATED 8 F., No. 609, Wan Shou Rd., Sec. 1, Kweishan, Taoyuan Hsien 33350, Taiwan. TEL: FAX: info@higgstec.com.tw Approve Review Preparation 確認審訂製表 Henry Andy Young

6.3 Customer Approval 客戶簽認 HIGGSTEC INCORPORATED 8 F., No. 609, Wan Shou Rd., Sec.

2 TABLE OF CONTENTS 目錄 00. Specification Revision Record [ 規格變更記錄 ] Dimension Drawing [ 尺寸圖 ] Scope [ 範圍 ] Features [ 特性 ] General Specification [ 一般規格 ] Environmental Characteristics [ 環境特性 ] Optical Characteristics [ 光學特性 ] Electrical Characteristics [ 電子特性 ] Mechanical Characteristics [ 機械特性 ] Reliability [ 可靠度 ] Durability [ 耐久性 ] Inspection Methods [ 檢查方法 ] Appearance Inspection [ 外觀檢查 ] Attention for Mounting Condition [ 裝機注意事項 ] Warranty [ 保固 ] Appendices [ 附註 ]. 09 Appearance Specification [ 外觀檢查規格 ] Caution [ 注意事項 ] Date: May 06, 2008 Version: 6.3

Mechanical Characteristics [ 機械特性 ].... 05 08. Reliability [ 可靠度 ].. 05 09. Durability [ 耐久性 ].. 05 10. Inspection Methods [ 檢查方法 ]... 06 11. Appearance Inspection [ 外觀檢查 ]. 07 12.

3 SPECIFICATION REVISION RECORD 規格變更記錄 Customer [ 客戶名稱 ]: Date [ 發行日期 ]:May 06, 2008 Customer NO. [ 客戶編號 ]: Model [ 型式 ]:T170S-5RB004N-0A18R0-200FH NO. [ 項次 ] Version. [ 版本 ] Date [ 變更發行日期 ] Summary of Changes [ 變更內容摘要 ] Page [ 變更頁碼 ] <Remarks>[ 備註欄 ] Date: May 06, 2008 Version: 6.3 Page: 01/11

5 01. Scope [ 範圍 ] 02. Features [ 特性 ] 03. General Specification [ 一般規格 ] The specification is for Five-Wire Analog Resistive touch panel. [ 此規格適用於五線 - 類比電阻式觸控屏幕 ] Item [ 項目 ] Specifications [ 規格 ] (1) Type Five-Wire Analog Resistive [ 型式 ] [ 五線 - 類比電阻式 ] Input Mode Stylus or Finger (2) [ 操作模式 ] (3) Cable [ 連結線 ] [ 筆觸或手觸 ] FFC Item [ 項目 ] Specifications [ 規格 ] Frame Size (1) ±0.30 X ±0.30 mm (2) (3) (4) (5) [ 外框尺寸 ] View Area [ 可視區 ] Active Area [ 動作區 ] Total Thickness [ 總厚度 ] Tail Length [ 出線長度 ] ±0.20 X ±0.20 mm ±0.20 X ±0.20 mm 2.20±0.20 mm ±6.00 mm 04. Environmental Characteristics [ 環境特性 ] Item [ 項目 ] (1) Operation [ 操作 ] (2) Storage [ 儲存 ] Temperature [ 溫度 ] -10 C ~ +70 C -40 C ~ +80 C Note: All terms under 1 atmosphere. [ 註 : 於正常的 1 大氣壓下 ] Specifications [ 規格 ] Humidity [ 濕度 ] (Non Condensing) [ 未凝結 ] 20%RH ~ 80%RH 10%RH ~ 85%RH Date: May 06, 2008 Version: 6.3 Page: 03/11

線 ] [ 筆觸或手觸 ] FFC Item [ 項目 ] Specifications [ 規格 ] Frame Size (1) 356.00±0.30 X 286.50±0.

6 05. Optical Characteristics [ 光學特性 ] 06. Electrical Characteristics [ 電子特性 ] Item [ 項目 ] Specifications [ 規格 ] (1) Transparency 80% ± 3% [ 透光度 ] (Measured by BYK-Gardner ) (2) Haze 8% ± 3% [ 霧化度 ] (1) Item [ 項目 ] Specifications [ 規格 ] Loop Resistance [ 迴路阻抗 ] (2) Linearity [ 線性 ] (3) Chattering [ 作動時間 ] (4) Insulation [ 絕緣阻抗 ] (5) Endurance [ 耐電壓 ] X:20~500Ω, Y:20~500Ω (See Figure 6-1) X 1.0%, Y 1.0% (See Figure 10-2) 15ms 20MΩ/25V(DC) No acting damage at DC50V/60sec. Figure 6-1 Loop Resistance X = short RT and RL, short LT and LL, measure the resistance between RT and LT Loop Resistance Y = short RT and LT, short RL and LL,measure the resistance between RT and RL Date: May 06, 2008 Version: 6.3 Page: 04/11

Specifications [ 規格 ] Loop Resistance [ 迴路阻抗 ] (2) Linearity [ 線性 ] (3) Chattering [ 作動時間 ] (4) Insulation [ 絕緣阻抗 ] (5) Endurance [ 耐電壓 ] X:20~500Ω, Y:20~500Ω (See Figure

7 07. Mechanical Characteristics [ 機械特性 ] Item [ 項目 ] Specification [ 規格 ] Condition [ 條件 ] Operating Force Stylus=R0.8 50g [ 作動力 ] Impact [ 撞擊 ] Static Load [ 靜態承重 ] Hardness [ 硬度 ] Peeling [ 剝離 ] Bending [ 繞折 ] [ 筆式 =R0.8] 13.0ψDIA. Steel Ball/9g Height=30cm [13ψ/9g 鋼球高度 =30cm] 500g within 10cm ² area for 30sec [500g 置於 10cm² 內,30 秒 ] 3H pencil, pressure 1N/45 [ 鉛筆 3H, 壓力 1N/45 (JIS K5400)] 800g by vertical 90 [800g, 垂直 90 ] times left & right [135 角, 左右來回 10 次 ] 1 time, no damage [Impact at center area] [ 中央區域撞擊 1 次, 不能破損 ] Satisfy(1) of Item 7 and (1), (2),(4) of Item 6 [ 符合 7 項目 (1) 及 6 項目 (1),(2),(4)] 3H Satisfy (1) of Item 6 [ 符合 6 項目 (1)] Satisfy (1) of Item 6 [ 符合 6 項目 (1)] 08. Reliability [ 可靠度 ] Item [ 項目 ] Specification [ 規格 ] Condition [ 條件 ] High Temperature /Humidity [ 高溫高濕 ] High temperature [ 高溫 ] Low temperature [ 低溫 ] Thermal Cycle [ 冷熱循環 ] 70 C /90%RH, 500 hrs, allow panel stays in normal environment for 4 hrs [70 C /90%RH,500 小時, 回常溫 4 小時後始可測試 ] 70 C /500 hrs allow panel stays in normal environment for 4 hrs [70 C /500 小時, 回常溫 4 小時後始可測試 ] -40 C /500 hrs allow panel stays in normal environment for 4 hrs [-40 C /500 小時, 回常溫 4 小時後始可測試 ] -40 C ~70 [60 min./cycle] *100 cycles allow panel stays in normal environment for 4 hrs [-40 C ~70 C, 每循環 60 分鐘, 共 100 次循環, 回常溫 4 小時後始可測試 ] Reliability test may cause the film puffed yet the electric characteristic stays intact. (1), (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies X 2.0%, Y 2.0%;Actuation force must not exceed 150g after reliability test. 經由可靠度測試後, 外觀不在其規範內, 但功能性仍符合以下條件 [ 符合 5 項目 (1) (2) 及 6 項目 (1) (4) ; 6 項目 (2) 符合 X 2.0%, Y 2.0%; 測試後作動力不能超過 150g] 09. Durability [ 耐久性 ] Item [ 項目 ] Specification [ 規格 ] Condition [ 條件 ] Knock Test 35,000,000 times Satisfy (1), (2) of Item 5; (1), (4) of Item 6; (2) of item 6 satisfies X 2.0%, Y 2.0%; Actuation force must not exceed 150g after durability [ 觸擊測試 ] [3500 萬次 ] test. [ 符合 5 項目 (1) (2) 及 6 項目 (1) (4) ; 6 項目 (2) 符合 X 2.0%, Y 2.0%; 測試後作動力不能超過 150g] Date: May 06, 2008 Version: 6.3 Page: 05/11

Steel Ball/9g Height=30cm [13ψ/9g 鋼球高度 =30cm] 500g within 10cm ² area for 30sec [500g 置於 10cm² 內,30 秒 ] 3H pencil, pressure 1N/45 [ 鉛筆 3H, 壓力 1N/45 (JIS K5400)] 800g by vertical 90 [800g, 垂直

8 10. Inspection Methods: [ 檢查方法 ] (1) Linearity Condition [ 線性測試條件 ] Step 1: short RT and RL(or short RL and LL). Step 2: apply voltage DC 5V. Step 3: short LT and LL (or short RT and LT). Step 4: apply grounding. Step 5: draw points along LX and LY at 5.0mm intervals within pattern area and detect the voltage at SG. Step 6: measure the voltage differences between RT and LT (or RT and RL) (Fig 10-1) (Fig 10-2) [ 將 RT, RL 短路 ( 或 RL, LL 短路 ) 並接上 5V 的直流電, 另外將 LT, LL 短路 ( 或 RT, LT 短路 ) 並接上接地線圈 0V, 以 5.0mm 的間隔, 利用手寫筆 (stylus) 劃直線 ( 如圖 2 中 LX 和 LY), 並量測 SG 的電壓, 量測並計算 RT 與 LT 間的電位差 ( 或 RT 與 RL 間的電位差 ) ] (Fig 10-1) (Fig 10-2) Figure 10-1 Figure 10-2 Linearity: [ Vxm-Vxi ] / (Va-Vb) X 100% (2) Specification [ 規範 ] Linearity must meet the electrical characteristic specified in Item 6 [ 線性必須符合 6 項目的電性規範 ] Date: May 06, 2008 Version: 6.3 Page: 06/11

Step 6: measure the voltage differences between RT and LT (or RT and RL) (Fig 10-1) (Fig 10-2) [ 將 RT, RL 短路 ( 或 RL, LL 短路 ) 並接上 5V 的直流電, 另外將 LT, LL 短路 ( 或 RT, LT 短路 ) 並接上接地線圈 0V, 以

9 11. Appearance Inspection [ 外觀檢查 ] (1) A 17W fluorescent luminant lamp is used for appearance inspection. Detail settings are shown in (Fig 11-1) and (Fig 11-2). [(1) 檢測始用之燈光為一盞 17W 白熾燈光, 詳細的擺設方式, 請參考圖 (Fig11-1), (Fig11-2) ] (2) Minor impurities outside viewing area are acceptable unless their existance affect electrical functions. [(2) 只要不影響電器功能性, 可視區外之外觀暇疵是可以被允許的 ]. Figure 11-1 Figure 11-2 (3) Glass Flaw [ 玻璃瑕疵 ] Item [ 項目 ] Picture [ 圖示 ] Specification [ 規格 ] Corner Flaw [ 角瑕疵 ] X 3.0mm Y 3.0mm Z T Edge Flaw [ 邊緣瑕疵 ] X 3.0mm Y 3.0mm Z T Progressive Flaw [ 裂縫瑕疵 ] Not allowed [ 不允許 ] Note: T=Glass thickness (4) Please refer to AppendixⅠ:Appearance Specification. [(4) 外觀規格請詳見 ( 附註 1)] Date: May 06, 2008 Version: 6.3 Page: 07/11

[(2) 只要不影響電器功能性, 可視區外之外觀暇疵是可以被允許的 ]. Figure 11-1 Figure 11-2 (3) Glass Flaw [ 玻璃瑕疵 ] Item [ 項目 ] Picture [ 圖示 ] Specification [ 規格 ] Corner Flaw [ 角瑕疵 ] X 3.0mm Y 3.

10 12. Attention of Mounting Condition [ 裝機注意事項 ] (1) The gasket support of touch panel must allocate outside of Viewable Area. Reserve enough clearance between panel surface and enclosure for normal panel operation. To avoid pressing error, please retain enough space between surface panel and Bezel. [ 請將固定觸控屏用的支撐體 (support) 設計於可視區 (Viewable area) 之外為避免不小心碰到觸控屏而產生動作, 請預留空間於面板與機體外殼之間 ] (2) Bezel opening must not touch Viewable Area, Bezel opening must be designed between Viewable Area and Active Area. [ 外殼內緣 (Bezel opening) 應設計於可視區及動作區之間, 並且不得碰到可視區 ] (3) We recommend elastic material support. [ 建議使用彈性物質製成的支撐體 ] (4) Due to the conductive characteristic of the panel backside, prevent metal contact after mounting. [ 觸控屏面板背面具導電性質,

[ 請將固定觸控屏用的支撐體 (support) 設計於可視區 (Viewable area) 之外為避免不小心碰到觸控屏而產生動作, 請預留空間於面板與機體外殼之間 ] (2) Bezel opening must not touch Viewable Area, Bezel opening must

Microsoft Word - 10100000191.doc

Microsoft Word - 10100000191.doc 臺灣集中保管結算所股份有限公司辦理認購 ( 售 ) 權證帳簿劃撥作業配合事項部分條文修正條文對照表附件 1 修正條文現行條文說明第五章認購 ( 售 ) 權證之權利行使第一節認購權證採證券給付或以證券給付之認購權證發行人得選