Datasheet 6MS16017P43W40382

Size: px

Start display at page:

Download "Datasheet 6MS16017P43W40382"

矢下丑
5 years ago
Views:

Generalinformation IGBTStackfortypicalvoltagesofupto0VRMS Ratedoutputcurrent0ARMS High power converter Wind power Motor drives IHM module with IGBT AlSiC baseplate Topology BI Application Inverter

1 Generalinformation IGBTStackfortypicalvoltagesofupto0VRMS Ratedoutputcurrent0ARMS High power converter Wind power Motor drives IHM module with IGBT AlSiC baseplate Topology BI Application Inverter Load type Resistive, inductive Semiconductor (Inverter Section) x FF00RKP_B DC Link mf Heatsink Water cooled Implemented sensors Current, voltage, temperature Driver signals IGBT Electrical Sales - name SP - No. SP0000 DC Link Inverter Section ~ ~ ~ Signal conditioning & monitor Driver phases Electrical interface

2 Absolutemaximumratedvalues Collector-emitter voltage IGBT; Tvj = C VCES 00 V Repetitive peak reverse voltage Diode; Tvj = C VRRM 00 V DC link voltage No switching, t= s, once a day VDC 00 V Insulation management according to installation height of 000 m Vline 0 VRMS Insulation test voltage according to EN 0, f = 0 Hz, t = s VISOL. kvrms Repetitive peak collector current inverter section (IGBT) Repetitive peak forward current inverter section (Diode) Continuous current inverter section tp = ms ICRM 0 A tp = ms IFRM 0 A IAC 0 ARMS Junction temperature under switching conditions Tvjop C Switching frequency inverter section fsw khz Notes Further maximum ratings are specified in the following dedicated sections Characteristicvalues DCLink min. typ. max. Rated voltage VDC 00 V Over voltage shutdown within 0 µs 0 V Capacitor s, 0 p, rated tol. ±0 % CDC mf type Foil Maximum ripple current per device, Tamb = C Iripple ARMS Balance or discharge resistor per DC link unit Rb kω Notes Operation above 00 V subject to reduced operating time according to EN 0 InverterSection min. typ. max. Rated continuous current Continuous current at low frequency VDC = 00 V, VAC = 0 VRMS, cos(ϕ) = 0., fac sine = 0 Hz, fsw = 000 Hz, Tinlet = 0 C, Tj C VDC = 00 V, fac sine = 0 Hz, fsw = 000 Hz, Tinlet = 0 C, Tj C IAC 0 ARMS IAC low 0 ARMS Rated continuous current for 0% overload capability Rated continuous current for 0% overload capability IAC 0% = 0 ARMS, ton over = 0 s, Tj C IAC over 0 ARMS IAC 0% = ARMS, ton over = s, Tj C IAC over 0 ARMS Over current shutdown within µs IAC OC 00 Apeak Power losses IAC = 0 A, VDC = 00 V, VAC = 0 VRMS, cos(ϕ) = 0., fac sine = 0 Hz, fsw = 000 Hz, Tinlet = 0 C, Tj C Ploss 00 W InverterSection(specificcondition) min. typ. max. Specific continuous current VDC = 00 V, cos(ϕ) = -0., fac sine = Hz, fsw = 00 Hz, Tinlet = C, Tj C IACsp 0 ARMS

3 Controllerinterface Driver and interface board ref. to separate Application Note DR0 min. typ. max. Auxiliary voltage Vaux 0 V Auxiliary power requirement Vaux = V Paux 0 W Digital input level resistor to GND. kω, capacitor to GND nf, logic high = on, min. ma Vin low 0 V Vin high V Digital output level open collector, logic low = no fault, max. ma Vout low 0. V Vout high V Analog current sensor output inverter section load max 0 ARMS VIU ana VIV ana VIW ana... V Analog DC link voltage sensor output load max 00 V VDC ana... V Analog temperature sensor output inverter section (NTC) Analog temperature sensor output inverter section (Simulated) Over temperature shutdown inverter section load max = C, corresponds to Tj = C at rated conditions load max = C, corresponds to Tj = C at rated conditions VTheta NTC. V VTheta sim. V VError OT 0 V Systemdata min. typ. max. EMC robustness according to IEC 00- at named interfaces power control aux (V) VBurst kv VBurst kv Vsurge kv Storage temperature Tstor -0 C Operational ambient temperature PCB, DC link capacitor, bus bar, excluding cooling medium Top amb - C Cooling air velocity PCB, DC link capacitor, bus bar, standard atmosphere Vair m/s Humidity no condensation Rel. F 0 % Vibration according to IEC 0 0 m/s² Shock according to IEC 0 00 m/s² Protection degree Pollution degree Dimensions width x depth x height 00 mm Weight kg IP00 Heatsinkwatercooled min. typ. max. Water flow according to coolant specification from Infineon V/ t dm³/min Water pressure bar Water pressure drop at dm³/min water flow p 0 mbar Coolant inlet temperature Tinlet -0 C Thermal resistance heatsink to ambient per switch Rth,ha 0.0 K/W Cooling channel material Notes Composition of coolant: Water and vol. % Antifrogen N Aluminum

4 Overviewofoptionalcomponents Parallel interface board Unit (not installed Voltage sensor Current sensor Temperature sensor Temperature simulation DC link capacitors Collector-emitter Active Clamping Notes Setting of Active Clamping TVS-Diodes: VZ = 0 V Inverter Section Unit (not installed)

5 fac sine - derating curve IGBT (motor), Diode (generator) VDC = 00 V, VAC = 0 VRMS, fsw = khz, cosϕ = ±0., Tinlet = 0 C and nom. cooling conditions fsw - derating curve IGBT (motor), Diode (generator) VDC = 00 V, VAC = 0 VRMS, fac sine = 0 Hz, cosϕ = ±0., Tinlet = 0 C and nom. cooling conditions IAC/Inom [%] IAC/Inom [%] IGBT, cosϕ = 0. Diode, cosϕ = IGBT, cosϕ = 0. Diode, cosϕ = fac sine [Hz] fsw [Hz] Tinlet - derating curve IGBT (motor), Diode (generator) VDC = 00 V, VAC = 0 VRMS, fsw = khz, fac sine = 0 Hz, cosϕ = ±0. and nom. cooling conditions Analog temperature sensor output VTheta NTC Sensing NTC of IGBT module IAC/Inom [%] IGBT, cosϕ = 0. Diode, cosϕ = -0. VTheta NTC [V] Tinlet [ C] TNTC [ C]

6 Tvj,sim vs. IAC - Simulated junction temperatur VDC = 00 V, VAC = 0 VRMS, fsw = khz, Tinlet = 0 C and nom. cooling conditions Analog temperature sensor output VTheta sim VDC = 00 V, VAC = 0 VRMS, fsw = khz, nom. cooling conditions 0 0 fac sine = 0 Hz fac sine = Hz fac sine = Hz 0 fac sine = 0 Hz fac sine = Hz fac sine = Hz 0 Tvj,sim [ C] VTheta sim [V] IAC [A] Tvj,sim [ C] Zth,ha - thermal impedance heatsink to ambient per switch nom. cooling conditions Zth,ha [K/W] i: ri[k/w]: τi[s]: t [s]

7 revision:. C D E F D b- ;- - - CE vgtokpcn #X# 0 Oqwpvkpi kp ecdkpgv Oqwpvkpi rqukvkqp UCF/ Oczkocn vqtswg hqt O dtcu urcegt< Po Oczkocn vqtswg hqt O rncuvke urcegt< -Po hkzgf ykvj Nqevkvg Oqwpvkpi rqukvkqp UCF CE vgtokpcn #W# Itqwpf O b- ; b- C H UY H CE vgtokpcn #Y# Itqwpf O z O pwv hqt oqwpvkpi kp ecdkpgv Ocz/ vqtswg Po b- ;-b- - b- ; - b- b- b- D)<* FE Vgtokpcn q b- date of publication: 0-0- approved by: YZ prepared by: OW Æpfgtwpigp Fcvwo Oqfgnn< C; Pcog dgtvcncp Ig / Xgvvgt Kp Dgctdgkvwpi Ocv/.Pt/< p Gtucv hþt< F; Gtugv v fwtej< DE. C Tgxkukqp< Dncvv.Pt/< OUTMR.YCJ.XE KIDV Uvcem OqfUvcem Fqmwogpvuvcvwu< Dgpgppwpi< Oz Alle Rechte bei INFINEON TECHNOLOGIES AG, auch für den Fall von Schutzrechtanmeldungen. Pcog PGTa0a // Rc/ PGTa0a; // Dgtvcncp Tgxkukqp Fcvwo Dgctd/ // Igrt/ // Pqto KUQ. om GP KUQ Ygtmuvqhh< Htgkocávqngtcp < Qdgthnæejg< Ocáuvcd< < ) < - < * C)<* CE Vgtokpcn )UY* H.H ) < * Nkhvkpi nwi p )z* KUQ ; Mcpvgp< FE okpwu vgtokpcn FE rnwu vgtokpcn Water connector M0x with protection cap (remove protection cap before use) Max Torque Nm During assembly the hose, the water connector (hose nozzle) must be held G b- H C D E F G H Technical Information Mechanical drawing

8 Technical Information Circuit diagram PWM U BOT X: PWM U TOP X: PWM V BOT X: PWM V TOP X: PWM W BOT X: PWM W TOP X:, X: Phase U Error TNTC Signal conditioning & Gate signals EiceDRIVERTM X: Top U Bottom X:, X: Phase V Error Phase W Error X: OT Error X: OV Error X: OC Error X: Sum Error Sensor signals TNTC Failure management X:0, X: GNDdigital X:, X: GNDdigital X:, X: GNDdigital X:, X:0 P X:, X: V X: V X: -V X: VIU ana X: VIV ana X: VIW ana X:0 VTheta NTC, VTheta sim X: VDC ana EiceDRIVERTM X:, X: Top V Bottom EiceDRIVERTM TNTC Power supply Top W Bottom X:, X: GNDanalog X: Vaux X: GND X: TE, Shield DC+ DR0 DC- V-Option Voltage measurement High voltage domain Low voltage domain X (male connector) X (male connector) X (male connector) SV (jumper) Th Tj Setting X:0 = VTheta NTC (Sensing NTC of IGBT module) X (male connector) Setting X:0 = VTheta sim (default setting) (Simulated junction temperature) prepared by: OW date of publication: 0-0- approved by: YZ revision:. ModSTACKTM

9 Technical Information Terms & Conditions of usage The data contained in this product data sheet is exclusively intended for technically trained staff. You and your technical departments will have to evaluate the suitability of the product for the intended application and the completeness of the product data with respect to such application. This product data sheet is describing the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its characteristics. Should you require product information in excess of the data given in this product data sheet or which concerns the specific application of our product, please contact the sales office, which is responsible for you (see sales&contact). For those that are specifically interested we may provide application notes. Due to technical requirements our product may contain dangerous substances. For information on the types in question please contact the sales office, which is responsible for you. Should you intend to use the Product in aviation applications, in health or live endangering or life support applications, please notify. Please note, that for any such applications we urgently recommend - to perform joint Risk and Quality Assessments; - the conclusion of Quality Agreements; - to establish joint measures of an ongoing product survey, and that we may make delivery depended on the realization of any such measures. If and to the extent necessary, please forward equivalent notices to your customers. Changes of this product data sheet are reserved. Safety Instructions Prior to installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. To installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. prepared by: OW date of publication: 0-0- approved by: YZ revision:.

Datasheet / Datenblatt 6MS10017E41W36460

Datasheet / Datenblatt 6MS10017E41W36460 Generalinformation IGBTStackfortypicalvoltagesofupto69VRMS Ratedoutputcurrent6ARMS High power converter Wind power Motor drives PrimePACK TM 3 module with integrated NTC Extended operational temperature