Microsoft Word - HB01-ENG.doc

Size: px

Start display at page:

Download "Microsoft Word - HB01-ENG.doc"

纪环郎
5 years ago
Views:

2 Preface Thank you for purchasing DELTA s DOP-B series. This quick start will be helpful in the installation, wiring and inspection of Delta HMI. Before using the product, please read this quick start to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring and operation. Place this quick start in a safe location for future reference. Please observe the following precautions: Install the product in a clean and dry location free from corrosive and inflammable gases or liquids. Ensure that all wiring instructions and recommendations are followed. Ensure that HMI is correctly connected to a ground. The grounding method must comply with the electrical standard of the country. Do not modify or remove wiring when power is applied to HMI. Do not touch the power supply during operation. Otherwise, it may cause electric shock. For the information of HMI software operation, and software installation, please refer to the HMI software manual. If you have any questions during operation, please contact our local distributors or Delta sales representative. The content of this quick start may be revised without prior notice. Please consult our distributors or download the most updated version at Safety Precautions Carefully note and observe the following safety precautions when receiving, inspecting, installing, operating, maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark safety precautions when using the Delta s HMI product. Failure to observe these precautions may void the warranty! Installation Wiring Comply with quick start for installation. Otherwise it may cause equipment damage. Do not install the product in a location that is outside the stated specification for the HMI. Failure to observe this caution may result in electric shock, fire, or personal injury. Connect the ground terminals to a class-3 ground (Ground resistance should not exceed 100Ω). Improper grounding may result in communication error, electric shock or fire. Operation The users should use Delta Screen Editor software to perform editing in Delta's HMI product. To perform editing and confirming HMI programs without using Delta Screen Editor software in Delta's HMI product may result in abnormal operation. Do not modify wiring during operation. Otherwise it may result in electric shock or personal injury. Never use a hard or pointed object to hit or strike the screen as doing this may damage the screen and let the screen has not respond at all, and then cause HMI to work abnormally. English-1

3 Maintenance and Inspection Wiring Method Do not touch any internal or exposed parts of the HMI as electrical shock may result. Do not remove operation panel while power is on. Otherwise electrical shock may result. Wait at least 10 minutes after power has been removed before touching any HMI terminals or performing any wiring and/or inspection as an electrical charge may still remain in the HMI with hazardous voltages even after power has been removed. Turn the power off before changing backup battery and check system settings after finishing change. (all data will be cleared after changing battery). Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result due to bad ventilation or overheating troubles. Remove the terminal block from the HMI before wiring. Insert only one wire into one terminal on the terminal block. If the wiring is in error, perform the wiring again with proper tools. Never use force to remove the terminals or wires. Otherwise, it may result in malfunction or damage. For the power line that forced to take out, ensure to check wiring again and restart. Communication Wiring Comply with communication wiring specification for wiring. Wiring length should comply with the stated specification for the HMI. Proper grounding to avoid bad communication quality. Installation and Storage Conditions The product should be kept in the shipping carton before installation. In order to retain the warranty coverage, the HMI should be stored properly when it is not to be used for an extended period of time. Some storage suggestions are: Store in a clean and dry location free from direct sunlight. Store within an ambient temperature range of -20 C to +60 C (-4 F to 140 F). Store within a relative humidity range of 10% to 90% and non-condensing. Do not store the HMI in a place subjected to corrosive gases and liquids. Correctly packaged and placed on a solid and durable surface. Do not mount the HMI adjacent to heat-radiating elements or in direct sunlight. Do not mount the HMI in a location subjected to corrosive gases, liquids, or airborne dust or metallic particles. Do not mount the HMI in a location where temperatures and humidity will exceed specification. Do not mount the HMI in a location where vibration and shock will exceed specification. Do not mount the HMI in a location where it will be subjected to high levels of electromagnetic radiation. Installation Installation Note: Improper installation will result in malfunction and greatly reduce the life of the HMI. Be sure to follow the guidelines in this quick start when installing the HMI. In order to ensure the HMI being well ventilated, make sure that the ventilation holes are not obstructed and must provide sufficient free space around HMI. For use on a flat surface of a Type 4X "Indoor Use Only" enclosure or equivalent. English-2

4 Installation Method: Step 1: Ensure to put waterproof gasket into HMI and then insert the HMI into the panel cutout. Step 2: Ensure to insert fasteners into the HMI s insertion slots and turn the screw till screws touch panel cutout. Step 3: Turn the screw with less than torque 0.7N.M to avoid damage to plastic box. Torque: 6.17lb-inch(0.7N-M) Step 4: Keep at least 60mm distance from rear of HMI product to the wall, installation surface or the other controllers for heat dissipation. Units:mm Power Line Installation Recommended wiring is in the table below: Type Wire Gauge (AWG) Stripped length Torque Solid 28 ~ 12 7 ~ 8 mm 5 Kg-cm Stranded 30 ~ 12 7 ~ 8 mm 5 Kg-cm Be sure to plug power line into HMI according to following arrow direction. English-3

5 Basic Inspection Item Content Periodically inspect the screws of the connection between the HMI and device. Tighten screws as necessary as they may loosen due to vibration and varying temperatures. Ensure that oil, water, metallic particles or any foreign objects do not fall General Inspection inside the HMI, control panel or ventilation slots and holes. As these will cause damage. Ensure the correct installation and the control panel. It should be free from airborne dust, harmful gases or liquids. Ensure that all wiring terminals are correctly insulated. Ensure that all wiring is correct or damage and or malfunction may result. Visually check to ensure that there are not any unused screws, metal strips, Inspection before any conductive or inflammable materials inside HMI. operation (power is not applied) Ensure to lower electromagnetic interference when devices are influenced by it. Ensure that the external applied voltage to HMI is correct and matched to the controller. Inspection before operation (power is applied) Check if power LED lights. Check if the communication among devices is normal. Please contact your local Delta sales representative if there are any abnormal conditions. Pin Definition of Serial Communication COM1 Port (Supports Flow Control) COM Port PIN1 Note: Blank = No Connection. Contact PIN RS RXD 3 TXD 4 5 GND 6 7 RTS 8 CTS 9 COM2 Port (Supports Flow Control) COM Port PIN1 PIN MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+ D+ 2 RXD 3 TXD 4 RXD+ 5 GND GND GND 6 TXD- D- 7 RTS 8 CTS 9 RXD- English-4

6 Note1: Blank = No Connection. Note2: When COM2 port is used for RS-232 flow control, i.e. RTS and CTS signals are used for flow control, COM3 port will become incapable of being used. Note3: When COM2 port is used for RS-422 flow control, please refer to the following COM3 Port signals table. The signals, RTS+, CTS+, RTS- and CTS- shown in brackets are the signals used for flow control. COM3 Port COM Port PIN MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+(RTS+) D+ 2 RXD 3 TXD PIN1 4 RXD+(CTS+) 5 GND GND GND 6 TXD-(RTS-) D RXD-(CTS-) Note1: Blank = No Connection. Note2: When COM2 port is used for RS-422 flow control, please refer to the COM3 Port signals table above. The signals, RTS+, CTS+, RTS- and CTS- shown in brackets are the signals used for flow control. Dimensions D A B C A User-defined Function Keys / System Keys User-defined Function Keys: F1, F2, F3, F4 System Keys:,,, SYS English-5

7 B C D One one-color LED Indicator: Power LED Indicator (Green) Lights in green when HMI works normally. One two-color LED Indicator: Left side: Operation LED Indicator (Blue) Right side: Alarm LED Indicator (Red) The operation LED indicator blinks in blue when either the communication is carried out or the data of USB flash drive is transmitting (please refer to the Note below for explanation). The alarm LED indicator blinks in red when one of the alarms is on. Operating / Display Area NOTE The users can determine the purpose of the operation LED indicator (what the operation LED indicator represents) in the system menu of DOP-B series HMI. G F E A B C D A B C D E F G Power Input Terminal COM3 (RS-232/RS-422/RS-485) (It is provided with two LED indicators to indicate that HMI is in Read or Write status during the communication process.) COM2 (RS-232/RS-422/RS-485) (It is provided with two LED indicators to indicate that HMI is in Read or Write status during the communication process.) COM1 (RS-232) USB Client USB Host Battery Cover English-6

8 (7.75" +0.04") 4-R (8.46") (5.63" +0.04") T NOTE: T=1.6 mm(0.063")~ 6 mm(0.24") (6.34") Units:mm Specifications MODEL Operation System Windows Base Real Time OS MCU 32-bit RISC Micro-controller NOR Flash ROM NOR Flash ROM 4 Mbytes Display Type Wide Screen TFT LCD (65536 colors) Resolution 480 x 234 pixels LCD MODULE Back Light CCFL Back Light (about 50 thousand hours at 25 o C) Display Size 7 inches wide screen ( x mm) SDRAM 16M bytes Backup Memory 256K bytes Sound Effect Buzzer Multi-Tone Frequency (2K ~ 4K Hz)/85dB Output AUX N/A Ethernet Interface N/A Extension CF Card N/A Memory USB Flash Drive USB for Download [USB Client] USB for Data Storage / Printer [USB Host] 1 Client Ver 1.1 USB English-7

9 MODEL Serial COM Port COM1 COM2 COM3 RS-232 RS-232/422/485 RS-232/422/485 Function Key User defined key x 4 + System key x 4 Perpetual Calendar (RTC) Cooling Method Safety Approval (Waterproof for front panel) Operation Voltage Built-in Natural air circulation IP65 / NEMA4 / CE, UL DC +24V (-10% ~ +15%) (Users please use isolated power supply.) Consumption Power 7.5W Backup Battery 3V lithium battery CR2032 x 1 Backup Battery Life It depends on the temperature used and the conditions of usage, about 3 years or more at 25 o C. Operation Temp. 0 C ~ 50 C Storage Temp. Ambient Humidity Vibration Resistance Dimensions (W) x (H) x (D) mm Panel Cutout (W) x (H) mm Weight -20 C ~ +60 C 10% ~ 90% RH [0 ~ 40 C], 10% ~ 55% RH [41 ~ 50 C] Pollution Degree 2 IEC Compliant 5Hz f<9hz = Continuous: 1.75mm / Occasional: 3.5mm 9Hz f 150Hz = Continuous: 0.5g / Occasional: 1.0g X, Y, Z directions for 10 times 215 x 161 x x Approx. 800g NOTE 1) Users can download the Screen Editor, the program editor of Delta HMI product and the user manual via the following link: English-8

10 序言感謝您使用本產品, 本人機介面安裝手冊提供 DOP-B 系列人機介面的相關資訊在使用之前, 請您仔細詳讀本手冊以確保使用上的正確此外, 請妥善將其放置在明顯的地點以便隨時查閱下列事項在您尚未讀完本手冊前, 請務必遵守 : 安裝的環境必須沒有水氣, 腐蝕性氣體及可燃性氣體接線時, 請依接線圖說明施工接地工程必須確實實施在通電時, 請勿拆解人機介面或更改配線在通電運作時, 請勿接觸電源處, 以免觸電如果您在使用上仍有問題, 請洽詢經銷商或者本公司客服中心由於產品精益求精, 當內容規格有所修正時, 請洽詢代理商或至台達網站 ( ) 下載最新版本安全注意事項安裝配線操作維護及檢查時, 應隨時注意以下安全注意事項安裝注意配線注意操作注意依照手冊指定的方式安裝人機介面, 否則可能導致設備損壞禁止將本產品暴露在有水氣腐蝕性氣體可燃性氣體等物質的場所下使用, 否則可能會造成觸電或火災請將接地端子連接到 class-3 (100 Ω 以下 ) 接地, 接地不良可能會造成通訊異常觸電或火災人機介面需配合編輯軟體規劃畫面, 未經規劃或確認之人機介面可能會導致不正常運轉結果不得在開啟電源情況下改變配線, 否則可能造成觸電或人員受傷請勿以尖銳物品碰觸面板, 否則可能導致面板凹陷, 進而使人機介面無法正常運作保養及檢查禁止接觸人機介面內部, 否則可能會造成觸電電源啟動時, 禁止拆下人機介面面板, 否則可能會造成觸電電源關閉 10 分鐘內, 不得接觸接線端子, 殘餘電壓可能造成觸電更換備用電池時, 應切斷電源再進行, 並在更換後重新檢查系統設定值人機介面在操作時, 排氣孔不可封住, 否則人機容易因為散熱不良而造成故障繁中 -1

11 配線方法通訊電路的配線配線時請將快速接頭從人機介面的本體上拆下來快速接頭的一個電線插入口, 請僅插入一根電線對於錯誤強行拔出電線的動作, 請重新檢查連接電線再啟動請依標準規格採用通訊配線線材通訊線材長度需在符合規定內採用正確的接地迴路, 以避免通訊不良安裝環境條件本產品在安裝之前必須置於其包裝箱內, 若暫時不使用, 為了使該產品能夠符合本公司的保固範圍及日後的維護, 儲存時務必注意下列事項 : 必須置於無塵垢乾燥之位置儲存位置的環境溫度必須在 -20 C to +60 C (-4 F to 140 F) 範圍內儲存位置的相對溼度必須在 10% 到 90% 範圍內, 且無結露避免儲存於含有腐蝕性氣液體之環境中最好適當包裝存放在架子或檯面本產品適合的安裝環境包括有 : 無發高熱裝置之場所;無水滴蒸氣灰塵及油性灰塵之場所;無腐蝕易燃性之氣液體之場所;無漂浮性的塵埃及金屬微粒之場所;堅固無振動無電磁雜訊干擾之場所安裝方向與空間注意事項 : 安裝方向必須依規定, 否則會造成故障原因為了使冷卻循環效果良好, 安裝人機介面時, 其上下左右與相鄰的物品和擋板 ( 牆 ) 必須保持足夠的空間, 否則會造成散熱不良使用於 Type 4X 室內用等級之外殼平面安裝示意圖 : 步驟一請確實將防水墊圈裝入, 然後再安裝人機介面步驟二請確實將固定片螺絲組裝入內, 然後下方鉤住前蓋螺絲頭頂住控制箱內側繁中 -2

12 步驟三請以 0.7N.M 扭力鎖緊, 切記不可超過此扭力, 否則將造成塑膠外殼的損壞扭力 : 6.17lb-inch(0.7N-M). 步驟四安裝時, 人機後方請預留 60mm 散熱空間單位 :mm 配線建議配線材料如下 : 種類電源配線 (AWG) 剝線長度扭力單芯線 28 ~ 12 7 ~ 8 mm 5 Kg-cm 多芯線 30 ~ 12 7 ~ 8 mm 5 Kg-cm 請確實依指示方向將快速接頭裝入基本檢測檢測項目檢測內容定期檢查人機介面與設備連接處的螺絲是否有鬆動排氣孔應避免油水或金屬粉等異物侵入, 且應防止電鑽的切削粉落入人機一般檢測介面內人機介面若設置於有害氣體或多粉塵的場所, 應防止有害氣體與粉塵的侵入配線端子的接續部請實施絕緣處理通訊配線應正確, 否則可能發生異常動作操作前檢測檢查螺絲或金屬片等導電性物體可燃性物體是否存在人機介面內 ( 未供應控制電源 ) 人機介面附近使用的電子儀器受到電磁干擾時, 請使用儀器調校以降低電磁干擾請確定人機介面的供應電源電壓準位是否正確繁中 -3

13 檢測項目檢測內容運轉前檢測電源指示燈是否顯示與各設備之間通訊動作是否正常 ( 已供應控制電源 ) 人機介面若有異常現象, 請與廠商聯絡通訊腳位定義 COM1 定義 ( 支援流量控制 ) COM Port 示意圖 PIN1 註 : 空白 = 不需連接說明腳位 RS RXD 3 TXD 4 5 GND 6 7 RTS 8 CTS 9 COM2 定義 ( 支援流量控制 ) COM Port 示意圖腳位 MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+ D+ 2 RXD 3 TXD PIN1 4 RXD+ 5 GND GND GND 6 TXD- D- 7 RTS 8 CTS 9 RXD- 註 1: 空白 = 不需連接註 2: 當 COM2 使用 RS-232 流量控制 (RTS CTS 腳位 ) 時,COM3 則無法使用註 3: 當 COM2 使用 RS-422 流量控制時, 其流量控制腳位請參考 COM3 MODE2 括號內的腳位定義 COM3 定義 COM Port 示意圖腳位 MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+(RTS+) D+ 2 RXD 3 TXD PIN1 4 RXD+(CTS+) 5 GND GND GND 6 TXD-(RTS-) D RXD-(CTS-) 註 1: 空白 = 不需連接註 2: 當 COM2 使用 RS-422 流量控制時, 其流量控制腳位請參考 MODE2 括號內的腳位定義繁中 -4

14 尺寸規格 D A B C A 自訂功能鍵 / 系統鍵自訂功能鍵 :F1, F2, F3, F4 系統鍵 :,,, SYS B 電源指示燈 ( 綠色 ) 綠燈亮 : 正常運作 C 動作指示燈 ( 藍色 )/ 警報指示燈 ( 紅色 ) 藍燈閃爍 :COM 通訊中 /USB 資料傳輸中 ( 註 ) 紅燈閃爍 : 警報發生中 D 操作 / 顯示區域註 : 藍色燈號代表意義可由使用者於人機系統畫面中自行設定繁中 -5

15 G F E A B C D A 電源輸入端子 E USB Client B COM3(RS232/RS422/RS485)( 支援通訊狀態指示燈號 ) F USB Host C COM2(RS232/RS422/RS485)( 支援通訊狀態指示燈號 ) G 電池外蓋 D COM1(RS232) (7.75" +0.04") 4-R (8.46") (5.63" +0.04") T (6.34") NOTE: T=1.6 mm(0.063")~ 6 mm(0.24") 單位 :mm 繁中 -6

16 硬體規格選項系統 OS 中央處理器 MCU LCD MODULE 記憶體 ROM Windows Base Real Time OS 32-bit RISC Micro-controller NOR Flash ROM 4 Mbytes 面板種類 7 寬螢幕 TFT LCD (65536 色 ) 解析度 480 x 234 pixels 背光燈 CCFL Back Light ( 常溫 25 o C 下壽命約 5 萬小時 ) 顯示範圍內部記憶體斷電保持內部記憶體 (Bytes) 音效輸出擴充記憶體網路介面蜂鳴器 AUX CF Card USB 程式下載 USB Client 資料儲存 / 列印 USB Host Serial COM Port COM1 COM2 COM3 7" ( x 86.58mm) 16Mbytes 256K Multi-Tone Frequency (2K ~ 4K Hz)/85dB N/A N/A N/A 1 Client Ver 1.1 RS-232 RS-232/422/485 RS-232/422/485 輔助鍵系統鍵 x 4 + 使用者定義鍵 x 4 萬年曆 RTC 內建冷卻方式自然冷卻安規認證 ( 面板防水等級 ) IP65 / NEMA4 / CE, UL 工作電壓 DC +24V (-10% ~ +15%) ( 請使用隔離 Power Supply) 消耗功率 7.5W 記憶體備份電池備份電池壽命 3V 鋰電池 CR 依使用環境溫度及使用條件而不同, 常溫 25 o C 下壽命約三年以上操作溫度 0 C to 50 C 繁中 -7

17 選項儲存溫度 -20 C to +60 C 工作環境 10% ~ 90% RH 0 ~ 40 C,10% ~ 55% RH 41 ~ 50 C, 污染等級 2 耐震動 / 耐衝擊尺寸 (W) x (H) x (D) mm 開孔尺寸 (W) x (H) mm 重量 IEC 規定不連續振動 5Hz-9Hz 3.5mm, 9Hz-150Hz 1G 連續振動 5Hz-9Hz 1.75mm, 9Hz-150Hz 0.5G X, Y, Z 各方向 10 次 215 x 161 x x 約 800g NOTE 1) DOP-B 系列 HMI 編輯軟體 Screen Editor 及其使用操作手冊, 可由台達網站下載取得, 網址為繁中 -8

18 序言感謝您使用本產品, 本人機界面安裝手冊提供 DOP-B 系列人機界面的相關信息在使用之前, 請您仔細詳讀本手冊以確保使用上的正確此外, 請妥善將其放置在明顯的地點以便隨時查閱下列事項在您尚未讀完本手冊前, 請務必遵守 : 安裝的環境必須沒有水氣, 腐蝕性氣體及可燃性氣體接線時, 請依接線圖說明施工接地工程必須確實實施在通電時, 請勿拆解人機界面或更改配線在通電運行時, 請勿接觸電源處, 以免觸電如果您在使用上仍有問題, 請咨询經銷商或者本公司客服中心由于產品精益求精, 當內容規格有所修正時, 請咨询代理商或至台達網站 ( ) 下載最新版本安全注意事項安裝配線操作維護及檢查時, 應隨時注意以下安全注意事項安裝注意配線注意操作注意依照手冊指定的方式安裝人機界面, 否則可能導致設備損壞禁止將本產品暴露在有水氣腐蝕性氣體可燃性氣體等物質的場所下使用, 否則可能會造成觸電或火災請將接地端子連接到 class-3 (100 Ω 以下 ) 接地, 接地不良可能會造成通訊異常觸電或火災人機界面需配合編輯軟件規劃畫面, 未經規劃或確認的人機界面可能會導致不正常運行保養及檢查不得在開啟電源情況下改變配線, 否則可能造成觸電或人員受傷請勿以尖銳物品碰觸面板, 否則可能導致面板凹陷, 進而使人機界面無法正常運行禁止接觸人機界面內部, 否則可能會造成觸電電源啟動時, 禁止拆下人機界面面板, 否則可能會造成觸電電源關閉 10 分鐘內, 不得接觸接線端子, 殘余電壓可能造成觸電更換備用電池時, 應切斷電源再進行, 並在更換后重新檢查系統設定值人機界面在操作時, 排氣孔不可封住, 否則人機容易因為散熱不良而造成故障简中 -1

19 配線方法通訊電路的配線配線時請將快速連接器從人機界面的本體上拆下來快速連接器的一個電線插入口, 請僅插入一根電線對于錯誤強行拔出電線的情況, 請重新檢查連接電線再啟動請依標準規格採用通訊配線線材通訊線材長度需在符合規定內採用正確的接地迴路, 以避免通訊不良安裝環境條件本產品在安裝之前必須置于其包裝箱內, 若暫時不使用, 為了使該產品能夠符合本公司的保固範圍及日后的維護, 儲存時務必注意下列事項 : 必須置于無塵垢干燥的位置儲存位置的環境溫度必須在 -20 C to +60 C (-4 F to 140 F) 範圍內儲存位置的相對溼度必須在 10% 到 90% 範圍內, 且無結露避免儲存于含有腐蝕性氣液體的環境中最好適當包裝存放在架子或檯面本產品適合的安裝環境包括有 : 無發高熱裝置的場所;無水滴蒸氣灰塵及油性灰塵的場所;無腐蝕易燃性的氣液體的場所;無漂浮性的塵埃及金屬微粒的場所;堅固無振動無電磁噪声干擾的場所安裝方向與空間注意事項 : 安裝方向必須依規定, 否則會造成故障原因為了使冷卻循環效果良好, 安裝人機界面時, 其上下左右與相鄰的物品和擋板 ( 牆 ) 必須保持足夠的空間, 否則會造成散熱不良使用于 Type 4X 室內用等級的外殼平面安裝示意圖 : 步驟一請確實將防水墊圈裝入, 然后再安裝人機介面步驟二請確實將固定片螺絲組裝入內, 然后下方鉤住前蓋螺絲頭頂住控制箱內側简中 -2

20 步驟三請以 0.7N.M 扭力鎖緊, 切記不可超過此扭力, 否則將造成塑膠外殼的損壞扭力 : 6.17lb-inch(0.7N-M). 步驟四安裝時, 人機后方請預留 60mm 散熱空間單位 :mm 配線建議配線材料如下 : 種類電源配線 (AWG) 剝線長度扭力單芯線 28 ~ 12 7 ~ 8 mm 5 Kg-cm 多芯線 30 ~ 12 7 ~ 8 mm 5 Kg-cm 請確實依指示方向將快速连接器裝入基本檢測檢測項目檢測內容定期檢查人機界面與設備連接處的螺絲是否有鬆動排氣孔應避免油水或金屬粉等異物侵入, 且應防止電鑽的切削粉落入人機一般檢測界面內人機界面若設置于有害氣體或多粉塵的場所, 應防止有害氣體與粉塵的侵入配線端子的接續部請實施絕緣處理通訊配線應正確, 否則可能發生異常操作前檢測檢查螺絲或金屬片等導電性物體可燃性物體是否存在人機界面內 ( 未供應控制電源 ) 人機界面附近使用的電子儀器受到電磁干擾時, 請使用儀器調校以降低電磁干擾請確定人機界面的供應電源電壓準位是否正確简中 -3

21 檢測項目檢測內容電源指示燈是否顯示運行前檢測與各設備之間通訊是否正常 ( 已供應控制電源 ) 人機界面若有異常現象, 請與廠商聯繫通訊引脚定義 COM1 定義 ( 支持流量控制 ) COM Port 示意圖 PIN1 註 : 空白 = 不需連接說明引腳 RS RXD 3 TXD 4 5 GND 6 7 RTS 8 CTS 9 COM2 定義 ( 支持流量控制 ) COM Port 示意圖引腳 MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+ D+ 2 RXD 3 TXD PIN1 4 RXD+ 5 GND GND GND 6 TXD- D- 7 RTS 8 CTS 9 RXD- 註 1: 空白 = 不需連接註 2: 當 COM2 使用 RS-232 流量控制 (RTS CTS 引腳 ) 時,COM3 則無法使用註 3: 當 COM2 使用 RS-422 流量控制時, 其流量控制引腳請參考 COM3 MODE2 括號內的引腳定義 COM3 定義 COM Port 示意圖引腳 MODE1 MODE2 MODE3 RS-232 RS-422 RS TXD+(RTS+) D+ 2 RXD 3 TXD PIN1 4 RXD+(CTS+) 5 GND GND GND 6 TXD-(RTS-) D RXD-(CTS-) 註 1: 空白 = 不需連接註 2: 當 COM2 使用 RS-422 流量控制時, 其流量控制引腳請參考 MODE2 括號內的引腳定義简中 -4

22 尺寸規格 D A B C A 自訂功能鍵 / 系統鍵自訂功能鍵 :F1, F2, F3, F4 系統鍵 :,,, SYS B 電源指示燈 ( 綠色 ) 綠燈亮 : 正常運行 C 动作指示燈 ( 藍色 )/ 警報指示燈 ( 紅色 ) 藍燈閃爍 :COM 通訊中 /USB 數據傳輸中 ( 註 ) 紅燈閃爍 : 警報發生中 D 操作 / 顯示區域註 : 藍色燈號代表意義可由使用者于人機系統畫面中自行設定简中 -5

23 G F E A B C D A 電源輸入端子 E USB Client B COM3(RS232/RS422/RS485)( 支持通訊狀態指示燈號 ) F USB Host C COM2(RS232/RS422/RS485)( 支持通訊狀態指示燈號 ) G 電池外蓋 D COM1(RS232) (7.75" +0.04") 4-R (8.46") (5.63" +0.04") T (6.34") NOTE: T=1.6 mm(0.063")~ 6 mm(0.24") 單位 :mm 简中 -6

24 硬件規格選項系統 OS 中央處理器 MCU 存儲器 ROM Windows Base Real Time OS 32-bit RISC Micro-controller NOR Flash ROM 4 Mbytes LCD MODULE 面板種類 7 寬屏幕 TFT LCD (65536 色 ) 分辨率 480 x 234 pixels 背光燈 CCFL Back Light ( 常溫 25 o C 下壽命約 5 萬小時 ) 顯示範圍 7" ( x 86.58mm) 內部存儲器斷電保持內部存儲器 (Bytes) 音效輸出網絡介面蜂鳴器 AUX 16Mbytes 256K Multi-Tone Frequency (2K ~ 4K Hz)/85dB N/A N/A 擴展存儲 CF Card N/A 器 USB 程序下載 USB Client 數據保存 / 打印 USB Host Serial COM Port COM1 COM2 COM3 1 Client Ver 1.1 RS-232 RS-232/422/485 RS-232/422/485 輔助鍵系統鍵 x 4 + 使用者定義鍵 x 4 實時時鐘 RTC 內建冷卻方式安規認證 ( 面板防水等級 ) 工作電壓自然冷卻 IP65 / NEMA4 / CE, UL DC +24V (-10% ~ +15%) ( 請使用隔離 Power Supply) 消耗功率 7.5W 存儲器備份電池備份電池壽命 3V 鋰電池 CR 依使用環境溫度及使用條件而不同, 常溫 25 o C 下壽命約三年以上简中 -7

25 選項操作溫度 0 C to 50 C 儲存溫度 -20 C to +60 C 工作環境 10% ~ 90% RH 0 ~ 40 C,10% ~ 55% RH 41 ~ 50 C, 污染等級 2 耐震動 / 耐衝擊尺寸 (W) x (H) x (D) mm 開孔尺寸 (W) x (H) mm 重量 IEC 規定不連續振動 5Hz-9Hz 3.5mm, 9Hz-150Hz 1G 連續振動 5Hz-9Hz 1.75mm, 9Hz-150Hz 0.5G X, Y, Z 各方向 10 次 215 x 161 x x 約 800g NOTE 1) DOP-B 系列 HMI 編輯軟件 Screen Editor 及其使用操作手冊, 可由台達網站下載取得, 網址為简中 -8

DOP-B(C-E)CURVE

DOP-B(C-E)CURVE Preface Thank you for purchasing DELTA s DOP-B series. This quick start will be helpful in the installation, wiring and inspection of Delta HMI. Before using the product, please read this quick start to