520PWC

Size: px

Start display at page:

Download "520PWC"

域蠡劳
5 years ago
Views:

Features/ 特征 : Single color/ 特征 High bright output/ 高亮度输出 Low power consumption/ 低功耗 High reliability and long life/ 可靠性高寿命长 Descriptions/ 描述 : Dice material/ 芯片材质 :InGaN Emitting Color/ 发光颜色 :

1 Features/ 特征 : Single color/ 特征 High bright output/ 高亮度输出 Low power consumption/ 低功耗 High reliability and long life/ 可靠性高寿命长 Descriptions/ 描述 : Dice material/ 芯片材质 :InGaN Emitting Color/ 发光颜色 : Super Bright White/ 高亮度白色 Device Outline/ 产品外形 : φ5mm Round Type/5mm 圆形 Lens Type/ 胶体颜色 :Water Clear/ 无色透明 Directivity/ 指向特性 : NOTE/ 注意 : All dimensions are millimeters/ 单位 :mm Tolerance is +/-0.25mmunless otherwise noted/ 没有标注的公差为 ±0.25mm Relative Luminous 相对亮度 Ta=25 C IF=20mA 60 DIRECTIVITY/ 指向特性 Radiation Angle 辐射角度 Rev :B/3 Page: 1 of 11

2 Absolute maximum ratings/ 极限参数 (Ta = 25 ) Parameter 参数 Reverse Voltage 反向电压 Forward Current 正向工作电流 Power Dissipation 损耗功率 Pulse Current 正向峰值电流 Operating Temperature 工作温度范围 Storage Temperature 储存温度范围 Symbol 符号 Test Condition Value 数值测试条件 Min. Max. Unit 单位 VR IR = 30μA 5 -- V IF ma Pd mw Ipeak Duty=0.1mS,1kHz ma Topr Tstr Electrical and optical characteristics / 光电参数 (Ta = 25 ) Parameter 参数 Forward Voltage 正向电压 Reverse Current 反向电流 Luminous Intensity 发光强度 Viewing Angle 指向角度 Symbol 符号 Test Condition Value 数值测试条件 Min. Typ. Max. Unit 单位 VF IF = 20mA V IR VR = 5V μa IV IF = 20mA mcd 2θ1/2 IF = 20mA Deg. Luminous Intensity Bins Chart/ 发光强度分档 (Ta = 25 ) Bin Z2 Z3 Z4 Z5 Min Max Rev :B/3 Page: 2 of 11

3 Chromaticity Coordinates Ranks / 色坐标分档 (IF=20mA Wa1 Wa3 Wa5 Wa7 Wa9 Wa11 Wb1 Wb3 Wb5 Wb7 Wb9 Wb11 Wc1 Wc3 Wc5 Wc7 Wd1 Wd3 Hebei I.T. (Shanghai) Co., Ltd. Ta=25 ) X X Y Wa2 Y X X Y Wa4 Y X X Y Wa6 Y X X Y Wa8 Y X X Y Wa10 Y X X Y Wa12 Y X X Y Wb2 Y X X Y Wb4 Y X X Y Wb6 Y X X Y Wb8 Y X X Y Wb10 Y X X Y Wb12 Y X X Y Wc2 Y X X Y Wc4 Y X X Y Wc6 Y X X Y Wc8 Y X X Y Wd2 Y X X Y Wd4 Y Rev :B/3 Page: 3 of 11

4 Wd5 Wd7 Hebei I.T. (Shanghai) Co., Ltd. X X Y Wd6 Y X X Wd8 Y Y CIE 1931 Chromaticity diagram wb wb10 wb7 wb11 wb wb4 wb8 wb12 wb1 wb5 wb9 wb2 wb6 wa wa10 wb3 wa11 wa wa7 wa8 wa12 wa4 wa9 wa5 wa1 wa2 wa3 wa6 Rev :B/3 Page: 4 of 11

5 wc wc1 wc2 wc3 wc wc5 wc6 wc7 wc8 we wf wf6 wf1 we5 wf7 wd we1 wf2 wf8 wd5 we6 wf3 wd1 we2 wf9 wd6 we7 wf4 wf10 wd2 we3 wf5 wd7 we8 wd3 we4 wd8 wd4 wc4 Rev :B/3 Page: 5 of 11

6 Typical electrical/optical characteristic curves/ 光电特性曲线 : Fig.1 正向电流 Vs. 正向电压 Fig.2 相对亮度 Vs. 正向电流 Forward Current(mA) Luminous Intensity Relative Value at IF=20mA Forward Voltage(V) IF-Forward Current (ma) Forward Current(mA) Fig.3 正向电流 Vs. 环境温度 Ambient Temperature TA ( ) 100 Relative Luminous Intensity Fig.4 相对亮度 Vs. 环境温度 Ambient Temperature TA ( ) Relative Luminous Intensity Fig.5 相对亮度 Vs 波长 Ta= Wavelength (nm) Rev :B/3 Page: 6 of 11

7 Relibility Analysis/ 可靠性试验 The reliability of products shall be satisfied with items listed below/ 产品的可靠性应该满足下面列表项目 : Confidence level:90% ;LTPD :10% Test Items And Results/ 测试项目和判据 No. Item/ 项目 Test Condition/ 测试条件 Time/ 时间 Q ty/ 数量 Standard/ 判定 1 Resistance to Tsld=235±5,5sec 3mm from Soldering Heat / the base of the epoxy bulb 抗焊接热 1 time 25 ALL PASS 2 Solder ability/ 可焊性 Tsld=235±5,5sec 1times Over 95% 25 ALL PASS Temperature Cycle/ 30min ~ 30min 高低温循环 The cut is not more than 2 min 50cycles 100 ALL PASS High Temperature 4 /High Humidity / 高温高湿 85 /85%RH 1000hrs 100 ALL PASS High Temperature Storage / 高温储存 Low Temperature Storage / 低温储存 DC Operation Life / 寿命测试 Ta= hrs 100 ALL PASS Ta= hrs 100 ALL PASS IF=20mA 1000hrs 25 ALL PASS Criteria For Judging Damage/ 判断标准 Symbol/ Test conditions Item/ 项目符号 / 测试条件 Criteria for Judgement / 判断标准 Min./ 最小值 Max./ 最大值 Luminous Intensity/ 亮度 Iv IF=20mA Iv*0.7 / Forward Voltage/ 正向电压 VF IF=20mA / U.S.L*1.1 Reverse current/ 反向电流 IR VR=5v / U.S.L*2 *U.S.L.:Upper Standard Level / 上限 *L.S.L.:Lower Standard Level / 下限 Rev :B/3 Page: 7 of 11

8 Label Form Specification/ 标签格式规范 P/N: Rank : / / Qty: Date: Lot No: pcs QC: P/N: Customer's Production Number/ 产品编号 QTY: Packing Quantity/ 包装数量 Ranks: Iv / Vf / WD Iv:Iv Rank/ 亮度 ;Vf:Vf Rank/ 电压 ;WD:Color Group/ 色系 QC: Quality Control chapter/ 质量控制章 Date: mm / dd / yy mm:month/ 月 ;dd:date/ 日 ;yy:year/ 年 ; Lot No: Production batch Number/ 生产批号 Lead Forming/ 成形 1. Any lead forming or bending must be done before soldering. 支架成形必须在焊接前完成 2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and the lead bend. 必需离胶体 2 毫米才能折弯支架 Rev :B/3 Page: 8 of 11

9 3. Avoid bending the leads at the same point more than once. 避免在管脚同一位置两次或多次弯 4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. 支架成形需保证引脚和间距与线路板上一致 5. Recommendations for manual plug-in operation, if really need taping machine for inserting operation, please make small batch prenatal confirmation. 建议手工插件作业, 若确实需要编带机插作业, 请进行小批量产前确认 Soldering Condition/ 焊接条件 Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint to case, and soldering beyond the base of the tie bar is recommended. 焊接时请特别注意, 焊接点要离 LED 封装体底部 2mm 以上 Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. 在 LED 处于高温, 特别是在焊接时, 请避免对支架施压 Recommended soldering conditions/ 推荐焊接条件 : Hand Soldering 手工焊接 DIP Soldering 浸焊 Temp.at tip of iron 电烙铁温度 300 Max.(30WMax.) 最高温度 300 ( 功率不超过 30 瓦 ) Preheat temp. 预热温度 100 Max. (60 sec Max.) 最高温度 100 ( 不超过 60 秒 ) Soldering time 焊接时间 3 sec Max. 时间不超过 3 秒 Bath temp. 浸焊温度 260 Max 最高 260. Distance 焊接位置 2mm Min.(From solder joint to case) 大于 2 毫米 ( 从焊点到胶体 ) Bath time. 浸焊时间 3 sec Max. 不超过 3 秒 Distance 浸焊位置 2mm Min 大于 2 毫米. Rev :B/3 Page: 9 of 11

10 Cleaning/ 清洗 1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. 不要用水清洗, 推荐使用酒精清洗, 当使用其他溶剂清洗时应事先确认该溶剂是否溶解树脂 2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. LED 有可能在超声波清洗过程中被破坏为了保证安全, 在清洗前, 请先确认 Storage/ 保存 1. Environmental temperature: , Recommended: 环境温度 : , 推荐使用 ; 2. Environmental humidity: 30%---70%, Recommended: 40%---60% 环境湿度 :30%---70%, 推荐使用 40%---60%; Static Electricity/ 静电 1. Static Electricity or power surge will damage the LED. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. 静电或激增电压将损害 LED 建议使用发光二极管时佩戴手腕带或防静电手套 2. All production machinery and test instruments must be electrically grounded. 所有的生产机器和检测仪器, 必须接地 Rev :B/3 Page: 10 of 11

11 3. Maintain a humidity level of 50% or higher in production areas. 生产现场湿度必须保持在 50% 或者更高 4. Use anti-static packaging for transport and storage. 使用防静电包装, 运输和储存 Notes/ 备注 1. This datasheet will be update regularly, if there comes out any changes, pls confirmed by the latest datasheet. 以上规格书会定期进行更新, 如有改动, 以最新规格书为准 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. HB assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 在使用本产品时, 请注意参考规格书中的最大额定值和使用说明, 如果没有遵照产品规格书中的最大额定值以及使用说明而产生的不良后果, 不在承诺范围之内 Rev :B/3 Page: 11 of 11

330MUV9C

330MUV9C Features/ 特征 : Single color/ 单色 High bright output/ 高亮度输出 3.9±.1 3.±.1 Low power consumption/ 低功耗 High reliability and long life/ 可靠性高寿命长 5.3±.1 2.9±.1 Descriptions/ 描述 : Dice material/ 芯片材质 :InGaN Emitting