Preface Preface Thank you for purchasing this product. Before using this product, read this document carefully so that you can use this product correc

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Preface Preface Thank you for purchasing this product. Before using this product, read this document carefully so that you can use this product correc"

Transcription

1 Instruction Manual

2 Preface Preface Thank you for purchasing this product. Before using this product, read this document carefully so that you can use this product correctly and safely. - i -

3 For safe usage For safe usage This document uses symbols for warnings, cautions, and prohibitions. These symbols and their meanings are as follows. Please make sure you fully understand the meanings of these symbols before reading the rest of this document. WARNING CAUTION PROHIBITED MANDATORY Indicates an item for which incorrect handling can result in a major accident involving death or serious injury. Indicates an item for which incorrect handling can lead to injury or damage to property. Under certain conditions, more serious consequences may result. Indicates a prohibited method of handling. Indicates a mandatory method of handling and a forcible item. WARNING and CAUTION for handling this product Do not perform any work while the vehicle is running. Doing so could result in an accident. WARNING Always observe the following rules. Failure to do so can result in heat generation, fire, blowout, or electrical shock. - Do not disassemble or alter this product. - Do not connect this product to anything with a voltage exceeding the ratings of this product. - Do not connect the probe to any parts applied by a voltage exceeding the ratings of this product. <Work environment> CAUTION Do not work anywhere that water could come in contact with the product and equipment. Block the wheels of the vehicle with chocks before carrying out work. Failure to do so could result in an accident. - ii -

4 For safe usage CAUTION When working anywhere hardly visible, for example under the vehicle, always make the vehicle starter switch (ignition switch) OFF to ensure that the vehicle cannot be moved. Failure to do so could result in an accident. When working near the engine compartment, be careful of the engine and other high-temperature parts. High-temperature parts can cause burns. Do not route the cable of this product over the engine compartment, especially if the engine is running. Failure to follow this instruction could result in an accident by catching up the cable and clothes with the belt and pulley. Do not use this product in an extremely dusty environment. The response of the LCD may be slow at the low temperature place. (Caution for the models with LCD) This phenomenon is attributed to the characteristics of the LCD and not a failure. <Checking before use> Inspect for adhesion of foreign materials to or pin breakage of each connector of this product before use. Before connecting the datalink cable to this product and the vehicle side diagnosis connector, inspect to see if each connector is contaminated with foreign materials or the connector pins are damaged. Before using the SD memory card, inspect to see if any foreign materials are stuck in the SD memory card slot or the contact surface of the SD memory card is contaminated with foreign materials. (Caution for the models with LCD) <Handling of the product and equipment> Do not drop this product or subject it to a strong impact. When connecting the datalink cable to this product and the vehicle side diagnosis connector or disconnecting it from them, ensure correct orientation of the connector and gently put it straight in. If the connector is connected in the wrong orientation, or put in or pulled out at the wrong angle, there is a risk of damaging the connector terminal and this may cause malfunctioning of the vehicle and/or this product. When connecting the USB cable to this product and a PC or disconnecting it from them, ensure correct orientation of the connector and gently put it straight in. If the connector is connected in the wrong orientation, or put in or pulled out at the wrong angle, there is a risk of damaging the connector terminal and this may cause malfunctioning of the PC and/or this product. When connecting the oscilloscope probe or ground cable to this product or when disconnecting it, ensure correct orientation of the connector and gently put it straight in. If the connector is connected in the wrong orientation, or put in or pulled out at the wrong angle, there is a risk of damaging the connector terminal and this may cause malfunctioning of this product. When pulling out the connector of cable, hold the connector section not the cord. Pulling on the cord section can break the lines in the cable. - iii -

5 For safe usage CAUTION Do not lift or drag this product by holding the cable connected to this product. When moving or installing, move this product by holding with hands. Do not apply the load causing stress to the connector connected to this product. Applying too much force could result in breaking the connector terminal and this may cause malfunctioning of the vehicle, the PC and/or this product. Do not insert anything other than an SD memory card in the SD memory card slot on this product. (Caution for the models with LCD) Do not turn the power of this product OFF or remove the SD memory card while the SD memory card indicator is flashing. (Caution for the models with LCD) Failure to do so results in failure of the SD memory card or loss of the data in it. Do not pull out an SD memory card when power is on. (Caution for the models with LCD) The tip of the probe is sharp, so handle it carefully. <Usage restrictions> Do not use a datalink cable other than the dedicated datalink cable supplied with this product. When you start this product only by USB power (BUS power), be careful not to set the PC to "low power consumption mode" / "suspend mode". The USB port to be connected to this product requires a power supply capability of 500 ma current source. As for connecting this product to the PC, directly connect it to the USB port on the PC or via a USB hub that has the capability of supplying sufficient current. Some types of USB hubs may have insufficient power supply capability for normal operation. (For example, a hub on PC keyboard is not suitable for this connection.) <Storage and maintenance of the product> Do not expose this product to direct sunlight for long periods of time. The backlight of the LCD may be deteriorated and its luminance could be reduced consequently in a high humid environment. (Caution for the models with LCD) Use and store this product in a dry environment. Do not use solvents or thinners such as benzine when cleaning. To do so could cause deformation, discoloration, cracking, etc., and also result in loss of functions. To clean, wipe gently with a soft damp cloth with diluted neutral detergent. <Disposal of the product> When discarding the product or its accessories, contact authorized industrial waste-disposal service. Those who discard waste without authorization will be punished by law. - iv -

6 For safe usage Disposal Requirements The product shall be disposed in accordance with all applicable legislation for disposal of Electrical and Electronic Equipment in each country and region. (e.g. WEEE Directive in EU) Please contact our authorized distributor or our sales agent when disposing it. - v -

7 For safe usage WARNING and CAUTION for Bluetooth (models with Bluetooth) WARNING Do not use this product near medical devices or inside medical facilities as it may affect electronic devices with medical applications. Make sure to keep this product at least 22 cm away from persons wearing a pacemaker. Radio wave could affect the performance of pacemaker. Do not use this product near an automatic control device such as an automatic door or a fire alarm. Radio wave could effect its operation and result in an accident caused by malfunction. Do not use this product in electric trains, airplanes, or places where flammable gasses are present. Failure to do so may result in accidents. CAUTION The communication range depends on any obstacles (i.e., human bodies, metal, walls) between this product and the Bluetooth device, and the condition of the radio wave. An antenna is built into this product. The sensitivity of the Bluetooth communication is maximized when no obstacles exist between the connected Bluetooth device and the antenna of this product. The communication distance becomes shorter should there be obstacles between the antenna of the connected Bluetooth device and the built-in antenna of this product. The following circumstances could affect the sensitivity of the Bluetooth communication. - Obstacles such as human body, metal, wall, etc. - In close proximity to established wireless networks, microwave ovens, and other devices that emit radio waves. Since Bluetooth devices and the wireless LAN (IEEE b/g) use the same frequency band (2.4 GHz), radio wave interference could occur and cause degradation of communication speed, noise and disconnection if a Bluetooth device is used near a wireless LAN equipped device. To resolve poor communications, perform the following steps. - Place this product as close to a Bluetooth device as possible. - Keep a wireless LAN equipped device away from this product as much as possible. - If communications do not improve, turn off any wireless LAN equipped devices nearby. Use the USB cable for more data critical situation over the Bluetooth communication (wireless) due to the greater possibility of loss of connection during data upload or download of the data transmission. Please note that we shall have no liability for any information leakage from the Bluetooth communication. - vi -

8 For safe usage The countries where you can use the models with Bluetooth Japan, USA, Canada, Australia, New Zealand, EU (Europian Union), Malaysia, Indonesia * In the countries other than those above, you cannot use the models with Bluetooth. Trademarks Microsoft, Windows, Internet Explorer, Windows 10, Windows 8.1, Windows 7 are the trademarks or registered trademarks of the Microsoft Corporation of the United States in the United States and other countries. Bluetooth is the trademark or registered trademark of Bluetooth SIG, Inc. in the United State and other countries. SD Memory Card TM and SDHC Memory Card TM are the registered trademarks of Panasonic Corporation, SanDisk Corporation in the United State and Toshiba Corporation. Names of products and companies in this document are registered trademarks or trademarks of their owners. TRON, itron and µitron are not the names for specific products and series of products. TRON is an abbreviation of "The Real-time Operating System Nucleus". µitron is an abbreviation of "Micro Industrial TRON". - vii -

9 Table of contents Table of contents 1 Before Use 1-1 Product Configuration... 1 Components...1 Optional products Names of the Parts... 3 models with LCD Setup... 4 Required operating environment of the PC...4 Necessary Setup Connection... 6 Connecting to the vehicle...6 Connecting to a PC...7 Connecting the oscilloscope probe...8 Connecting the ground cable SD Memory Card Inserting/removing an SD memory card Basic Operations 2-1 Starting Ending Indicator 3-1 Indicator Product Specifications 4-1 Specifications of This Product Oscilloscope Function Specifications Warranty 5-1 Warranty viii -

10 1 Before Use 1 Before Use 1-1 Product Configuration Check that you have all of the following standard components before using this product. Components Set Part Number: * (with LCD, without Bluetooth) * (with LCD, with Bluetooth) No. Part Name Illustration Part No. Q'ty 1 Main unit with LCD T01856Z 1 2 Datalink Cable * 1 T01857Z 3 Oscilloscope probe * 2 T02053Z 4 Ground cable * 1 T02052Z 5 USB Cable * 1 T01871Z 6 USB Spacer * 1 T02747Z 7 SD memory card * 1 T02715Z 8 Instruction Manual (this document) 1 NOTE The last figure of a part No. is indicated with *. When you ask for information, make inquiries with the 9-digit part No. and part name

11 1 Before Use Optional products Part Name Illustration Part No. Q'ty 4-channel adapter set * Adapter (1) Probe (2) T02054Z NOTE The last figure of a part No. is indicated with *. When you ask for information, make inquiries with the 9- digit part No. and part name

12 1 Before Use 1-2 Names of the Parts The names of the product parts are as follows: models with LCD Overall LCD B key Up/Down/Right/Left keys A key Indicators * For detailed information about indicators, refer to "Chapter 3 Indicator/3-1 Indicator". Upper side USB connector* Connector for datalink cable DC jack* When using a DC jack, the part set as an option. Left side Plug jack Right side Mode switch Oscilloscope probe connector SD memory card slot* * Rubber caps are provided for "USB connector", "DC jack", "SD memory card slot" and "oscilloscope probe connector and plug jack". T02586E - 3 -

13 1 Before Use 1-3 Setup You must carry out the setup necessary for use of this product. Required operating environment of the PC For using this product, a PC with following operating environments is required. OS: Microsoft Windows 7 (SP1) (32bit, 64bit) English version Microsoft Windows 8.1 (32bit, 64bit) English version Microsoft Windows 10 (32bit, 64bit) English version With USB 2.0 interface as standard Internet Explorer 11.0 or later version should be installed. Access to Internet is allowed. (Broadband internet connection is recommended) NOTE If this product is used as the interface, the operating environment of the software on a PC side is needed in addition to the above operating environment. Confirm the latest information in the following website

14 1 Before Use Necessary Setup For using this product, following setup is needed. Installing DST-i setup software to a PC (all models) A dedicated USB driver, the setup utility (DST-i configuration tool), etc. which is required for connecting this product and a PC using a USB cable or Bluetooth shall be installed to the PC. Installing the DST-i main unit software to this product (all models) Install the DST-i main unit software to this product. Installing Bluetooth driver software and Paring to a PC (models with Bluetooth) For the models with Bluetooth, to connect this product with a PC through the Bluetooth communication function, you must install the Bluetooth driver software to the PC beforehand. In addition, you must execute pairing between the PC and this product. Installing the oscilloscope software Install the oscilloscope software to this product and the PC. When installing the oscilloscope software to this product, an SD card is required. CAUTION Do not connect this product with a PC using the USB cable before the DST-i setup software installation to your PC is completed. To install the DST-i setup software to a PC, log on with administrator privileges and close all running applications before installation. In installing the DST-i main unit software, execute the install by using the USB cable in the state that this product and the PC are connected. Do not execute the install in using Bluetooth communication. Use of a Bluetooth driver software equipped as standard to the PC with Microsoft Windows operating system is recommended for use of a Bluetooth communication. This information does not guarantee the connection between all of commercially available Bluetooth modules and information terminals equipped with Bluetooth (e.g., PC and cellular phone). Use a Bluetooth module that is labeled with the Bluetooth logo mark and conforms to the Bluetooth standard 2.0. Total eight Bluetooth modules and information terminals having Bluetooth can execute paring with this product. If ninth Bluetooth module or information terminal executes paring, first Bluetooth module or information terminal will be cancelled. 1. Access the following website and setup the this product and the PC following the displayed instructions

15 1 Before Use 1-4 Connection Connecting to the vehicle Use the datalink cable to connect this product with the vehicle. Check the position of the diagnosis connector of the vehicle side in the repair manual of the vehicle. CAUTION Perform the connection of step 1 and step 2 according to the order. 1. First, connect this product and the datalink cable. 2. Next, connect the datalink cable to the vehicle side diagnosis connector. [2] Connected to vehicle side diagnosis connector Notch (Center) [1] Connected to this product Tighten with screws. T02929E NOTE The power supply of this product is turned ON by turning the mode switch ON after connected with the vehicle

16 1 Before Use Connecting to a PC Use a USB cable to connect this product to a PC. Connected to the USB connector into the PC USB cable T02006E NOTE The power supply of this product is turned ON by turning the mode switch ON after connected with a PC. When the USB communication with the PC is established, the PC communication (USB) indicator on this product lights or flashes in green. When establishing the connection with the Bluetooth communication function on the models with Bluetooth, USB cable connection is not needed. If connecting with a PC with the Bluetooth communication, communication setup must be performed with the DST-i configuration tool. When the Bluetooth communication with the PC is established, the PC communication (Bluetooth) indicator on this product lights or flashes in blue. When connecting the model with Bluetooth to a PC with the USB cable, the USB communication has the top priority in the communication between a PC. When communication way is changed from USB to Bluetooth while communicating, remove the USB cable with the PC application software finished. CAUTION You must install the DST-i setup software on your PC before you connect the USB cable to your PC. Reference: Page 5 Installing DST-i setup software to a PC (all models) (Chapter 1 Before Use/Setup/Necessary Setup) When the PC does not supply adequate power, please contact your distributor

17 1 Before Use Connecting the oscilloscope probe When using the oscilloscope function, connect the oscilloscope probe to this product. Cap The tip of the probe can be removed. Tip of the probe Oscilloscope probe Ch1 Ch2 Connect the oscilloscope probe to Ch1 or Ch2. The probe can be connected to both Ch1 and Ch2. T02716E NOTE The tip of the oscilloscope probe can be removed. <After using the oscilloscope probe> Cap T02717E NOTE After using the oscilloscope, always put the cap back on it

18 1 Before Use To increase the number of oscilloscope channels, use the optional 4-channel adapter. Ch1 Ch2 About the guides <DST-i side> <4-channel adapter side> 4-channel adapter Guide (male) Guide (female) Connect the 4-channel adapter to Ch2. The connector may only be connected to Ch2. Line up the male and female portions of the guide when connecting the connector. *It cannot be connected to Ch1. T02059E NOTE By using the 4-channel adapter, the number of channels can be increased to four. Connecting the ground cable When a stable waveform display cannot be obtained while using the oscilloscope function because of noise, connect the ground cable to this product. Connect to vehicle ground T02058E NOTE Attach the clip of the ground cable to a stable location where it can be grounded on the vehicle. CAUTION Do not remove ground with anything but the vehicle ground. It may cause malfunctioning of the vehicle and/or this product

19 1 Before Use 1-5 SD Memory Card Inserting/removing an SD memory card This product can use an SD memory card inserting it into the SD memory card slot. The SD memory card may be used to install software or store vehicle data. CAUTION Depending on software, some functions with SD memory cards are not available. Refer to the instruction manual of the software to know whether your software supports the functions or not and the handling method. Use an SD memory card or an SDHC memory card. This product does not support an SDXC memory card. Use an SD memory card labeled with the SD logo mark and conforming to the SD standard. The following brand SD memory cards are recommended: Panasonic, SanDisk and Toshiba Not all the SD memory cards are supported on this product. Inserting an SD memory card 1. Turn the mode switch of this product OFF. 2. Turn the notch of SD memory card to the right and insert gently to the slot end until a clicking noise is heard. Notch to be on the right side Available card SD SDHC Confirm the logo mark of the card. T02085E NOTE If the notch on the SD memory card side face is set to the "Lock" position, data storage and deletion are disabled by the write protect function (write inhibit). Make sure to unlock the write protect function before use. Removing an SD memory card 1. Turn the mode switch of this product OFF. 2. Push the SD memory card lightly. 3. The SD memory card is ejected a little. Pull out it gently

20 2 Basic Operations 2 Basic Operations 2-1 Starting CAUTION Perform the connection of step 1 and step 2 according to the order. 1. Connect the datalink cable to this product. Reference: Page 6 Connecting to the vehicle (Chapter 1 Before Use/Connection) 2. Connect the datalink cable to the vehicle side diagnosis connector. Reference: Page 6 Connecting to the vehicle (Chapter 1 Before Use/Connection) 3. Connect this product and a PC with the USB cable. Reference: Page 7 Connecting to a PC (Chapter 1 Before Use/Connection) NOTE If you do not use a PC, you do not need to connect with the USB cable. If you use a model with Bluetooth and connect with a PC through the Bluetooth communication function, you do not need to connect with the USB cable. 4. Turn the mode switch of this product ON. Mode switch T01897E NOTE When turning the mode switch ON, the power indicator of this product turns green. 5. Turn the vehicle starter switch (ignition switch) ON. NOTE When the vehicle starter switch (ignition switch) position is OFF or ACC, communication with the vehicle cannot be established. Turn the vehicle starter switch (ignition switch) ON or start the engine when using this product

21 2 Basic Operations 2-2 Ending 1. Finish communications with the vehicle by PC application software or LCD software. CAUTION Do not turn the mode switch of this product OFF or disconnect the datalink cable from this product during the active test. The diagnosed actuators could be stopped still in the drive status. Make sure to execute the ending procedure after finishing the active test. 2. Turn the mode switch of this product OFF. 3. Turn the vehicle starter switch (ignition switch) OFF. 4. Disconnect the USB cable from this product and the PC. CAUTION When disconnecting the datalink cable from the vehicle side diagnosis connector, go after turn the vehicle starter switch (ignition switch) OFF. Perform the disconnection of step 5 and step 6 according to the order. 5. Disconnect the datalink cable from the vehicle side diagnosis connector. 6. Disconnect the datalink cable from this product

22 3 Indicator 3 Indicator 3-1 Indicator The indicators of this product provide the following information by their illumination. [Power] indicator [Vehicle] indicator [PC (Bluetooth)] indicator [Power] indicator Shows the status of power. Lights in green during power ON. [Vehicle] indicator Shows the status of communications with the vehicle. Flashes in green during active communications. [PC (Bluetooth)] indicator Shows the status of Bluetooth communications with the PC. Flashes in blue during active communications. [PC (USB)] indicator Shows the status of USB communications with the PC. Flashes in green during active communications. [Error] indicator Lights or flashes in red when an error occurs. [SD Memory Card] indicator Shows the access status of the SD memory card. Flashes in green during active access. [PC (USB)] indicator [Error] indicator T01900E [SD memory card] indicator T01917E

23 4 Product Specifications 4 Product Specifications 4-1 Specifications of This Product Item Specifications OS µitron CPU 32-bit RISC microcomputer Built-in Flash ROM 16 MB Memory SDRAM 16 MB EEPROM 32 KB Size 2.7 inch TFT color LCD LCD Resolution QVGA (320 x 240 dots) Display color Max colors Input device Operation keys 6 keys USB USB 2.0 x 1 Bluetooth *1 Bluetooth 2.0 class 1 SD memory card Slot x 1 (supporting SD and SDHC memory cards) External interface *2 DC jack JEITA4 standard type Connector for Oscilloscope probe 2ch Vehicle communication Dedicated connector (D-sub 25 pin) x 1 ISO9141, CAN Main unit power Vehicle power supply DC 6.5 to 32 V (Datalink cable) supply voltage USB power (BUS power) DC 4.75 to 5.25 V *3 Power consumption Normally 1.5 W (12 VDC), Max. 2.5 W (12 VDC) Operating temperature Operating 0 to 50 C [-10 to 60 C] [Storage temperature] environment Operating humidity 35 to 85% (No condensation) Dimensions 135 mm (W) x 70 mm (H) x 35 mm (D) Weight Model without Bluetooth Approx. 230 g Model with Bluetooth Approx. 235 g *1 For models with Bluetooth only *2 Some functions require the support software. *3 This product can be turned on by the power supplied from the USB power (BUS power). However, vehicle communication cannot be established when the power is not supplied from the vehicle

24 4 Product Specifications 4-2 Oscilloscope Function Specifications Number of channels Maximum sampling rate Voltage axis range Time axis range Trigger mode Rated input voltage Item Specifications 4 channels (2 channels standard + 2 channels optional) 64 MS/sec 20 mv/div, 50 mv/div, 100 mv/div to 15 V/div 500 ns/div, 1 µs/div, 2 µs/div to 10 s/div Auto, Normal, Single 70 V

25 5 Warranty 5 Warranty 5-1 Warranty 1. The warranty period of this set is two years after the purchase day. However accessories are not covered, main body only. 2. Free repair warranty is applied only for the failure under proper operation conditions within the warranty period. 3. Non-free repair is applied to the following cases even if the valid warranty period remains. Failure or damage from fire and natural disaster. Failure or damage as a result of a falling during transportation and movement after purchase or from the improper handling. Failure or damage caused from handling in a way contrary to proper operating methods and cautions described in this document. Failure or damage from modification or liability for operations. Replacement of external parts such as the resin case. 4. We shall have no liability for any direct or indirect damage resulting from failure or use of this product. 5. For request of repair, please contact your distributor. Data preservation Recorded data in this product could be lost in repair. Please note that we shall have no liability for any damage and data preservation derived in conjunction with data loss

26 5 Warranty DENSO Overseas Subsidiary Company & TAS CORPORATION name/address DENSO AUTOMOTIVE SYSTEMS AUSTRALIA PTY. LTD. Address: 2-46 Merrindale Drive, Croydon, Victoria 3136, Australia DENSO INTERNATIONAL ASIA PTE. LTD. Address: 51 Science Park Road, #01-19 The Aries, Science Park II, Singapore PT.DENSO SALES INDONESIA Address: Jl.Gaya Motor I No.6, Sunter II, Kel.Sungai Bambu, Kec.Tanjung Priok, Jakarta 14330, Indonesia DENSO (MALAYSIA) SDN. BHD. Address: Lot 2, Jalan P/1, Section 13, Bandar Baru Bangi, Selangor Darul Ehsan, Malaysia DENSO PHILIPPINES CORPORATION Address: 109 Unity Avenue, Carmelray Industrial Park 1, 4037 Canlubang, Calamba City, laguna, Philippines DENSO TAIWAN CORP. Address: 525, Sec. 2 Mei Su Road Yang Mei Town Taoyuan Hsien, Taiwan, R.O.C. DENSO SALES (THAILAND) CO.,LTD. Address: 888 Moo1, Bangna-Trad Rd. Km. 27.5, Tambol Bangbo, Amphur Bangbo, Samutprakarn Thailand DENSO EUROPE B.V. Address: Hogeweyselaan 165, 1382 JL Weesp, The Netherlands DENSO SALES MIDDLE EAST & NORTH AFRICA FZE Address: P.O.Box , Jebel Ali Free Zone South, Dubai, United Arab Emirates DENSO (CHINA) INVESTMENT CO.,LTD. Address: Room No.518, The Beijing Fortune Building, No.5 Dong San Huan Bei Lu, Chaoyang District, Beijing, China DENSO INTERNATIONAL INDIA PVT. LTD. Address: Plot No.3, Sector-3, IMT Manesar, Gurgaon, Haryana , India DENSO PRODUCTS AND SERVICES AMERICAS, INC. Address: 3900 Via Oro Avenue, Long Beach, California 90810, U.S.A. DENSO SALES CANADA, INC. Address: 195 Brunel Road, Mississauga, Ontario, Canada, L4Z 1X3 DENSO INTERNATIONAL KOREA CORPORATION Address: 131, Seonggogae-ro, Uiwang-si, Gyeonggi-do, Korea TAS CORPORATION Address: Shimoshiota Narumi-cho, Midori-ku, Nagoya, Aichi, , JAPAN Tel/Fax Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: /33 Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax:

27 Regulatory Information to user MODEL : DN-VIM EMC and Radio Regulation in U.S.A. Model with Bluetooth, Model without Bluetooth FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. NOTICE: This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model with Bluetooth CAUTION: Radio Frequency Radiation Exposure This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person s body (excluding extremities: hands, wrists, feet and ankles). Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 3. EMC in KOREA Model without Bluetooth : DENSO CORPORATION : Diagnostic Tester (DN-VIM-003) : DENSO CORPORATION/ : KCC-REM-DKR-DN-VIM-003 : Refer to serial number on product. For more information please contact DENSO INTERNATIONAL KOREA CORPORATION. T02978Z

28 4. EMC and Radio Regulation in CANADA Model with Bluetooth NOTE Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This device has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person's body (excluding extremities: hands, wrists, feet and ankles). Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. L opération est soumise aux deux conditions suivantes: (1) Ce périphérique ne peut être la cause d interférence, et (2) Ce périphérique se doit d accepter toute(s) interférense(s), y compris celle(s) susceptible(s) de provoquer des opérations indésirables dans le cadre de son fonctionnement. Cet équipement est en conformité avec les limites d exposition aux rayonnements IC précédemment énoncées dans un environnement non contrôlé et répond aux règles d exposition aux radiofréquences (RF) IC définies par RSS-102. Parce qu il bénéficie de très faibles niveaux d énergie RF, cet équipement a été jugé conforme sans qu il soit nécessaire de procéder à une évaluation de l exposition permissive maximale (MPE). Toutefois, il est recommandé que cet équipement soit installé et opéré en prenant soin que le radiateur soit à une distance minimum de 20 cm de toute personne se trouvant dans sa périphérie (à l exclusion des extrémités corporelles suivantes: mains et poignets et, pieds et chevilles). Co-implantation: Cet émetteur ne doit pas être co-implanté ou exploité conjointement avec une autre antenne ou émetteur. 5. EMC and Radio Directive in EU, EFTA Model without Bluetooth 2014/30/EU Harmonized Standards applied : EN (This product falls under group 1 and class A) : EN Model with Bluetooth 2014/53/EU Harmonized Standards applied : EN V2.1.1 Manufacturer Name Address : DENSO CORPORATION : 1-1 Showa-cho, Kariya-shi, Aichi-ken, Japan Authorised representatives Name Address Model Name Radio Frequency Radio Output Power : DENSO EUROPE B.V. : Hogeweyselaan 165, 1382 JL Weesp, the Netherlands : DN-VIM-003 : MHz : 20 dbm max. T02979Z

29 T02980Z ț

30 6. Radio Regulation in MALAYSIA Model with Bluetooth Model name : DN-VIM-003 Manufacturer : DENSO CORPORATION 7. Radio Regulation in INDONESIA Model with Bluetooth 33991/SDPPI/ Environmental Regulation in CHINA Table of toxic or hazardous substances contained in this product for "Management Methods for Controlloing Pollution by Electronic Information Products (China RoHS)". T02981Z

31 Instruction Manual 1st Ed. September, th Ed. October, 2017 First setup date Store purchased S/N