SCD-XA9000ES

Transcription

1 (1) Super Audio CD Player Operating Instructions GB CT TM S200 SCD-XA9000ES 2003 Sony Corporation

2 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with news papers, tablecloths, curtains, etc. And don t place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. Don t throw away the battery with general house waste, dispose of it correctly as chemical waste. Welcome! Thank you for purchasing the Sony Super Audio CD Player. Before operating the unit, please read this manual thoroughly and retain it for future reference. About This Manual The instructions in this manual is for SCD- XA9000ES. Conventions Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player. The following icons are used in this manual: Z Indicates that you can do the task using the remote. z Indicates hints and tips for making the task easier. 2 GB

3 Features TABLE OF CONTENTS About the Super Audio CD Super Audio CD is a new high-quality audio disc standard where music is recorded in the DSD (Direct Stream Digital) format (conventional CDs are recorded in the PCM format). The DSD format, using a sampling frequency 64 times higher than that of a conventional CD, and with 1-bit quantization, achieves both a wide frequency range and a wide dynamic range across the audible frequency range, and so provides music reproduction extremely faithful to the original sound. The Super Audio CD has two types; a 2 channel stereo disc and a Multi-channel disc which holds up to 6 independent channels. The multi-channel characteristic of the Super Audio CD features a speaker allocation system basically similar to the 5.1 channel output of current AV systems. Features of the player This player is designed to play back 2-channel and multichannel Super Audio CDs, and conventional CDs, and provides the following features: Mounted with a Discrete Dual Laser Optical Pickup, capable of reading a Super Audio CD or conventional CD depending on the exclusive wavelength. Quicker track access performance enabled by an advanced servo mechanism. A Multi-Channel Management function that allows you to adjust the multi-channel playback environment according to the allocation and size of your speakers. A Super Audio D/A Converter and Direct Digital Sync System, which allows higher-quality sound reproduction. An i.link digital transmission system that provides higher quality sound and lets you make connections with just 1 i.link cord instead of 6 pin cords. This player complies with DTLA copy protection technology (Revision 1.2). Others A Super Audio CD can mark up to 255 track/index numbers. This feature applies to SCD-XA9000ES. The supplied remote is capable of controlling both the SCD-XA9000ES and a conventional Sony CD player. Getting Started 4 Before You Start the Hooking Up 4 Hooking Up the Audio Components 5 Location and Functions of Parts 10 Front Panel Parts Descriptions 10 Rear Panel Parts Descriptions 12 Remote Parts Descriptions 13 Playing Discs 14 Compatible Disc Types 14 Playing a Disc 16 Using the Display 17 Locating a Specific Track 20 Locating a Particular Point in a Track 20 Playing Tracks Repeatedly 21 Playing Tracks in Random Order (Shuffle Play) 22 Creating Your Own Program (Program Play) 23 Listening to a CD Using a Filter (Digital Filter Function) 24 Setting the DIGITAL OUT on/off 24 Listening to a Multi-channel Super Audio CD (Multi-channel management function) 25 Additional Information 29 Precautions 29 Notes on Discs 30 Troubleshooting 31 Display Messages 32 Specifications 32 Index 34 GB 3 GB

4 Getting Started This chapter provides information on the supplied accessories and how to connect various audio components to the Super Audio CD player. Be sure to read this chapter thoroughly before you actually connect anything to the player. Before You Start Hooking Up Checking the supplied accessories This player comes with the following items: Audio connecting cord phono jack 2 (Red and White) y phono jack 2 (Red and White) (3) phono jack 1 (Black) y phono jack 1 (Black) (2) i.link connecting cord (1) Remote commander RM-SX700 (1) Size AA (R6) batteries (2) AC power cord (1) Plug adapter (1) (North American model only) Inserting batteries into the remote Insert two size AA (R6) batteries into the battery compartment with the + and correctly oriented to the markings. When using the remote, point it at the remote sensor on the player. z When to replace the batteries Under normal conditions, the batteries should last for about six months. When the remote no longer operates the player, replace both batteries with new ones. Notes Do not leave the remote in an extremely hot or a humid place. Do not drop any foreign object into the remote casing, particularly when replacing the batteries. Do not use a new battery with an old one. Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction. If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. 4 GB

5 Getting Started Hooking Up the Audio Components Connect the Super Audio CD player to an audio component. Be sure to turn off the power of all components before making connections and connect securely to prevent noise. CENTER or SUB WOOFER connection Audio connecting cords (Black) (supplied) Black Black If you have an amplifier equipped with the 5.1CH input jacks (multi-channel amplifier, AV amplifier, etc.) and connect the player and the amplifier via the ANALOG 5.1CH OUT jacks, you can play multi-channel Super Audio CDs and enjoy multi-channel playback. For normal playback, connect the player and an amplifier via ANALOG 2CH OUT jacks. Connecting via ANALOG 5.1CH OUT jacks Use audio connecting cords for this connection. Connect the ANALOG 5.1CH OUT jacks (FRONT L/R, SURR L/R, CENTER, SUB WOOFER) to the corresponding jacks on your amplifier. For FRONT or SURR connection, use the connecting cords (Red and White jacks) and be sure to match the color-coded pin to the appropriate jacks: white (left) to white and red (right) to red. For CENTER and SUB WOOFER connection, use the connecting cords (Black). Notes Even when you make Multi-channel connections, be sure to also connect the ANALOG 2CH OUT jacks using another audio connecting cord so that you can play CDs (or s) when you set the input selector of your amplifier to CD (or ) input. During playback of a conventional CD or a 2CH Super Audio CD, same signal is output from the ANALOG 5.1CH FRONT L/R jacks and ANALOG 2CH OUT jacks. The signal is output in higher quality from the ANALOG 2CH OUT jacks (see page 9). During playback of a Multi-channel Super Audio CD, the same signal is output from the ANALOG 5.1CH FRONT L/R jacks and ANALOG 2CH OUT jacks. (The downmixed signal of the Multi-channel signal is not played back.) There are 5CH, 4CH, and 3CH Super Audio CD. When you play these disc, the signal is not output from all of the ANALOG 5.1CH OUT jacks. For details of the playback, see the cover or instructions of the Super Audio CD. FRONT or SURR connection Audio connecting cords (Red and White) (supplied) White (L) Red (R) White (L) Red (R) CENTER L L R R FRONT SURROUND SUB WOOFER 5.1CH OUT COAXIAL OPTICAL OUT DIGITAL(CD) AUDIO OUT i.link S200 AC IN R L 2CH OUT ANALOG To FRONT IN jacks (L/R) To SURROUND or REAR IN jacks (L/R) To CENTER IN jack To SUB WOOFER IN jack Multi-channel amplifier, AV amplifier, etc. 5 GB

6 Getting Started Hooking Up the Audio Components Connecting via ANALOG 2CH OUT jacks Use an audio connecting cords for this connection. Connect the ANALOG 2CH OUT L/R jacks to the CD () input jacks of your amplifier. Be sure to match the color-coded pin to the appropriate jacks: white (left) to white and red (right) to red. Audio connecting cords (Red and White) (supplied) White (L) Red (R) White (L) Red (R) Note During playback of a Multi-channel Super Audio CD, the same signal is output from the ANALOG 5.1CH FRONT L/R jacks and ANALOG 2CH OUT jacks. (The downmixed signal of the Multichannel signal is not played back.) About the ANALOG 2CH OUT When you play a conventional CD or a 2CH Super Audio CD, the stereo signal is sent to the FRONT, SURROUND, and CENTER/ SUB WOOFER D/A Converters, and each signal is combined after D/A conversion, then combined signal is output from the 2CH OUT jacks. Since each digital signal is converted to analog signal by three converters, this system offers a 3-times increase in signal, with only a 3-times increase in noise, for an improved signal to noise ratio. Therefore, a high quality signal is output from the ANALOG 2CH OUT jacks. During playback of a Multi-channel Super Audio CD, the signal conversion described above is not applied, and the same signal is output from the ANALOG 5.1CH FRONT L/R jacks and ANALOG 2CH OUT jacks. (The downmixed signal of the Multichannel signal is not played back.) CENTER L L R R FRONT SURROUND SUB WOOFER 5.1CH OUT COAXIAL OPTICAL OUT DIGITAL(CD) AUDIO OUT i.link S200 AC IN R L 2CH OUT ANALOG To CD () IN jacks (L/R) Stereo amplifier, etc. 6 GB

7 Getting Started Connecting via i.link S200 AUDIO OUT jack Connect SCD-XA9000ES to STR-DA9000ES/TA- DA9000ES with the supplied i.link connecting cord. i.link connecting cord (supplied) Notes i.link connections are only possible between this player and STR-DA9000ES/TA-DA9000ES. This player has some restrictions on i.link functions and may not operate properly if connected to components other than STR-DA9000ES/TA- DA9000ES. If a metal object should fall into the i.link S200 AUDIO OUT jack, short-circuiting may occur and damage the components. Be sure to insert the plug firmly to prevent malfunction. See page 32 for information about compatible signals. Some i.link components comply with copy protection technology and handle encrypted signals. This player complies with the DTLA copy protection technology (Revision 1.2). i.link lights up in the display when this player is ready to output the audio signals from the i.link S200 AUDIO OUT jack. Establishing a LINC Before an audio signal can be transmitted between i.link components, a LINC (Logical INterface Connection) must first be established between the receiving component (of the audio signal) and the sending component. Establishing a LINC means establishing a logical path for the transmission of digital audio signals between the two components. Each logical path has an ID number. Since the component that sends an audio signal must output the signal to a path, and the component that receives the signal must input it from the same path, the path must be mutually known by both components. During the establishment of a LINC, the following communication occurs between the two i.link components. Example STR-DA9000ES/TA-DA9000ES establishes a LINC with SCD- XA9000ES. 1 STR-DA9000ES/TA-DA9000ES sends a request and path information to SCD-XA9000ES to establish a transmission path for the audio signal. STR-DA9000ES TA-DA9000ES 1, 2 < SCD-XA9000ES 2 SCD-XA9000ES responds to STR-DA9000ES/TA-DA9000ES, agreeing to the establishment of a LINC. The digital audio signal transmission becomes possible only after the communication described above has occurred and a LINC has been established. CENTER L L R R FRONT SURROUND SUB WOOFER 5.1CH OUT COAXIAL OPTICAL OUT DIGITAL(CD) AUDIO OUT i.link S200 AC IN R L 2CH OUT ANALOG To i.link S200 AUDIO IN jack STR-DA9000ES TA-DA9000ES 7 GB

8 Getting Started TM Hooking Up the Audio Components Listening in high fidelity H.A.T.S. (High quality digital Audio Transmission System) function When the H.A.T.S. function of STR-DA9000ES/TA- DA9000ES is ON digital audio signals are momentarily stored in a buffer, then read with exact timing before being converted to analog. This eliminates the jitter (timing lapses) that sometimes occur during digital signal transmission and greatly improves sound quality. When this function is turned on, H.A.T.S. lights up in the display of STR-DA9000ES/TA-DA9000ES whenever the digital audio signal is input to the receiver. When not using this function, set it to OFF on STR-DA9000ES/ TA-DA9000ES. For details, refer to the Operating Instructions supplied with STR-DA9000ES/TA- DA9000ES. Notes Because of the way the H.A.T.S. function operates, a slight time lag is introduced between each operation (e.g., pressing play, stop, or pause) and its implementation. The duration of this time lag may be different for CD and Super Audio CD sources. The H.A.T.S. function works only with H.A.T.S. compatible components. The H.A.T.S. function works only when this player is selected as the input source by a single STR-DA9000ES/TA-DA9000ES. This is because the receiving component (STR-DA9000ES/TA- DA9000ES) controls the rate of digital audio signal transmission from the player. To insure proper signal transmission within the i.link configuration, only one component can receive the digital audio signals output from a source component. Copyright i.link components complying with copyright protection incorporate digital data copy protection technology. One such technology is the DTLA (The Digital Transmission Licensing Administrator) recognized by the Copy Protection Technical Working Group. It may not be possible to make digital copies of copy restricted digital data (video/audio/data) using i.link signals between components that comply with the DTLA copy protection technology. In addition, it may not be possible to transfer digital data (video/audio/data) via i.link between i.link components which comply with DTLA copy protection and i.link components which do not. i.link is a designation referring to IEEE and IEEE 1394a i.link and the i.link logo are trademarks of Sony Corporation. Connecting via DIGITAL (CD) OUT OPTICAL connector Use an optical digital cable for this connection. When connecting the optical digital cable to the DIGITAL (CD) OUT OPTICAL connector, take the cap off the connectors and push the cable plugs in until they click into place. Be careful not to bend or twist the optical cable. Optical digital cable (not supplied) Note Only the audio signals of conventional CDs can be output from the DIGITAL (CD) OUT connectors. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT. When the i.link indicator is lit No signal is output from DIGITAL (CD) OUT OPTICAL connector. Connecting via DIGITAL (CD) OUT COAXIAL connector Use a coaxial digital cable to connect the audio components equipped with coaxial digital input connectors. Coaxial digital cable (not supplied) Note Only the audio signals of conventional CDs can be output from the DIGITAL (CD) OUT connectors. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT. When the i.link indicator is lit No signal is output from DIGITAL (CD) OUT COAXIAL connector. Connecting the AC power cord Connect the supplied AC power cord to the AC IN terminal on the player and to the mains. 8 GB

9 Getting Started Note on the output jacks This player is equipped with a Tri-Powered D/A Converter System and a Multi Channel Management function. The usable output settings differ depending on the mode you select as follows. For details, refer to the Operating Instructions. Source Multi 2CH 5.1CH PHONES DIGITAL Channel OUT OUT jack (CD) OUT Manage- jacks jacks jacks ment CD Not available a* 1 a a* 1 a* 3 Super Audio CD Direct a* 1 a a* 1 (2 channel) 2ch + SW a a a Super Audio CD (Multi-channel) Available for all playback modes a* 2 a a* 2 * 1 Output through the Tri-Powered D/A Converter. * 2 The same signal that is output from the ANALOG 5.1CH OUT FRONT L/R jacks is output. * 3 Only when D. OUTPUT is set to ON (page 24). Note Tri-Powered D/A Converter System works only for 2 channel signals from 2 CH OUT jacks. When the i.link indicator is lit No signal is output from all the other jacks (ANALOG 2CH OUT jacks, ANALOG 5.1CH OUT jacks, PHONES jack, DIGITAL (CD) OUT jacks). The Multi Channel Management function does not work. z When you want to listen to the sound through headphones when the i.link indicator is lit Connect the headphones to the PHONES jack on the amplifier, not on this player. 9 GB

10 Location and Functions of Parts Front Panel Parts Descriptions This chapter tells you about the location and functions of the various buttons and controls on the front and rear panels and the supplied remote. Further details are provided on the pages indicated in parentheses. It also tells you about the information that appears in the display window. 1 POWER switch (16) Press to turn on the player. 2 TIME/TEXT button (17) Each time you press the button, the playing time of the track, the total remaining time on the disc, or TEXT information appears in the display. 3 /CD button (16) Each time you press the button while playing back a hybrid disc, the layer to be played back switches between the HD (Super Audio CD) layer and the CD layer. 4 i.link button (16) Each time you press the button, i.link function turns on or off. i.link indicator (16) Lights up when the i.link function is used. 5 Disc tray (16) Press A OPEN/CLOSE to open/close the disc tray. 10 GB

11 Location and Functions of Parts POWER TIME/TEXT MENU MULTI/2CH /CD i.link AMS PHONES PHONE LEVEL MIN MAX PUSH ENTER 6 A OPEN/CLOSE button (16) Press to open or close the disc tray. 7 N button (16) Press to start play. N indicator (16) Lights up during playback. 8 X button (16) Press to pause play. X indicator (16) Lights up during pause. 9 x button (16) Press to stop play. 0 PHONES Connect the headphones. During playback of a Multi-channel Super Audio CD, the same signal that is output from the ANALOG 5.1CH FRONT L/R jacks is output from the PHONES jack. qs MENU (15, 26 28) Press to enter the menu. Press to exit from the menu and return to the normal display. qd MULTI/2CH button (16) Press to select the playback area when the 2 channel + Multi-channel Super Audio CD (page 15) is loaded. qf Remote sensor qg Display window (17) Shows various information. qh. AMS > dial (AMS: Automatic Music Sensor) (20) When you turn the. AMS > dial counterclockwise by one click, you go back to the preceding track; when you turn the. AMS > dial clockwise by one click, you go to the succeeding track. qa PHONE LEVEL Adjust the headphones volume. 11 GB

12 Location and Functions of Parts Rear Panel Parts Descriptions CENTER L L R R FRONT SURROUND SUB WOOFER 5.1CH OUT COAXIAL OPTICAL OUT DIGITAL(CD) AUDIO OUT i.link S200 AC IN R L 2CH OUT ANALOG 1 ANALOG 5.1CH OUT jacks (5) Connect to an amplifier equipped with the 5.1CH input jacks (Multi-channel amplifier, AV amplifier, etc.) using the audio connecting cords. 2 DIGITAL (CD) OUT COAXIAL connector (8) Connect to an audio component using the coaxial digital cable. 3 DIGITAL (CD) OUT OPTICAL connector (8) Connect to an audio component using an optical digital cable. Note Only the audio signals of the CD can be output from the DIGITAL (CD) OUT connectors shown in 2 and 3. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT connectors. When the i.link indicator is lit No signal is output from all the other jacks (ANALOG 2CH OUT jacks, ANALOG 5.1CH OUT jacks, PHONES jack, DIGITAL (CD) OUT jacks). 4 i.link S200 AUDIO OUT jack (7) Connect to STR-DA9000ES/TA-DA9000ES using the i.link connecting cord. 5 AC IN terminal (9) Connect the AC power cord. 6 ANALOG 2CH OUT L/R jacks (6) Connect to an audio component (stereo/2 channel) using the audio connecting cord. 12 GB

13 Location and Functions of Parts Remote Parts Descriptions 1 CONTINUE button (22) Press to resume normal play from Shuffle Play or Program Play. SHUFFLE button (22) Press to select Shuffle Play. PROGRAM button (23) Press to select Program Play. 2 DISPLAY MODE button (18) Press to turn the display information off or on. 3 TIME/TEXT button (17) Each time you press the button, the playing time of the track, the total remaining time on the disc, or TEXT information appears in the display. 4 Number buttons (20) Press to enter the track numbers. 5 i10 button (20) Press to locate a track numbered over REPEAT button (21) Press repeatedly to play all tracks or only one track on the disc. 7 AyB button (22) Press to select Repeat A-B Play. 8 H button (16) Press to start play. X button (16) Press to pause play. x button (16) Press to stop play. 9 AMS./> (AMS: Automatic Music Sensor) buttons (20) Press to locate a specific track. qs /CD button (16) Each time you press the button, or CD appears in the display. Select the type of CD you want to play. qd MULTI/2CH button (16) Press to select the playback area when the 2 channel + Multi-channel Super Audio CD (page 15) is loaded. qf ENTER button (27) Press to decide the selection. qg CLEAR button (23) Press to delete a programed track number. qh LEVEL ADJ button (27) Press to adjust the output level balance for the Multichannel management function (page 25). qj CHECK button (23) Press to check the programed order. PLAY MODE CONTINUE SHUFFLE PROGRAM /CD TIME/TEXT MULTI/2CH >10 ENTER 10/0 REPEAT DISPLAY/ MODE CHECK CLEAR 0 m/m buttons (20) Press to locate a portion you want to play within a track. A B LEVEL ADJ qa INDEX >/. buttons (20) Press to locate a specific point marked with an index signal when you play a disc that has index signals. AMS INDEX 13 GB

14 Playing Discs This chapter explains the various ways to play discs. Compatible Disc Types You can play the following discs with this player. Depending on the type of disc to be played, select the appropriate indicator by pressing /CD or MULTI/ 2CH (page 16). Classification by the layer configuration Super Audio CD (single layer disc) This disc consists of a single HD (high density) layer. When you play this disc, the player is set to the Super Audio CD playback mode automatically. HD (Super Audio CD) layer Super Audio CD (dual layer disc) This disc consists of dual HD layers and is capable of extended play over long periods. When you play this disc, the player is set to the Super Audio CD playback mode automatically. Also, as the dual layer disc consists of dual HD layers on one side only, it is not necessary to turn the disc over. HD (Super Audio CD) layer HD (Super Audio CD) layer Conventional CD This disc is the standard format. When you play this disc, the player is set to the Conventional CD playback mode automatically. CD layer 14 GB

15 Playing Discs Super Audio CD + CD (Hybrid disc) This disc consists of an HD layer and a CD layer. Press /CD to select the layer you want to listen to. Also, as the dual layers are on one side, it is not necessary to turn the disc over. You can play the CD layer using a conventional CD player. 2 channel + Multi-channel Super Audio CD This disc consists of the 2 channel playback area and the multi-channel playback area. Press MULTI/2CH to select the playback area you want to listen to. 2 channel playback area CD layer Selecting the default playback layer (HD or CD) 1 During stop mode, press MENU. HD (Super Audio CD) layer 2 Turn. AMS > until /CD SEL appears in the display. 3 Press. AMS >. The current playback layer appears. 4 Turn. AMS > to select desired playback layer, then press. AMS >. Classification by the channel configuration of the Super Audio CD 2 channel Super Audio CD This disc consists of the 2 channel playback area. When you play this disc, the player is set to the 2 channel playback mode automatically. Selecting the default playback area (2 channel or multi-channel) 1 During stop mode, press MENU. 2 Turn. AMS > until M/2CH SELECT appears in the display. 3 Press. AMS >. The current playback area appears. 4 Turn. AMS > to select desired playback area, then press. AMS >. Incompatible Discs Multi-channel playback area This player cannot play the following discs. If you try to play them, the error message TOC Error or No Disc will appear or there will be no sound. CD-ROM DVD, etc. 2 channel playback area Multi-channel Super Audio CD This disc consists of the multi-channel playback area. When you play this disc, the player is set to the multichannel playback mode automatically. Multi-channel playback area 15 GB

16 Playing Discs Playing a Disc The operations for normal play and the basic operations during play are explained below. Basic operations during play To Press POWER /CD A OPEN/CLOSE N X x Stop play Pause play Resume play after pausing Locate a succeeding track x X X or N Turn. AMS > clockwise Locate the beginning of the Turn. AMS > current track or a preceding counterclockwise track i.link.ams> Eject the disc A OPEN/CLOSE 1 Turn on the amplifier. Turn down the volume level to the lowest. 2 Select the player position using the input selector on the amplifier. 3 Press POWER to turn on the player. 4 Press A OPEN/CLOSE to open the disc tray, and place a disc on the tray. With the label side up 5 Press N. Playback starts from the first track. If you want to start playing from a specific track, turn. AMS > to select the track number before pressing N. 6 Adjust the volume on the amplifier. z If you turn on the player when a disc is already loaded Playback starts automatically. If you connect a commercially available timer, you can set it to start playing the disc at any time you want. z To select a layer you want to listen to when playing a hybrid disc (page 15) Press /CD repeatedly to light either the or CD. z To select a playback area you want to listen to when playing a 2 channel + Multi-channel Super Audio CD (page 15) Press MULTI/2CH repeatedly to light either the MULTI CH or 2 CH. Notes During playback, increase the volume level gradually starting from the lowest level. The output from this unit may contain band width that are out of the normal listening range. This may cause damage to the speakers or ears. When you change the playback area during the Program Play mode, the program is cleared. When you change the playback area, the playback starts from the beginning of the same track. However, the playback starts from the first track depending on the disc. To use the i.link function You can output the sound through i.link S200 AUDIO OUT jack and enjoy the high quality sound. Refer to the Operating Instructions supplied with the connected component. Press i.link to turn on the i.link indicator. To turn off the i.link function and listen to the analog sound, press i.link again to turn off the i.link indicator. Note If you press N while the connected component is not ready for the i.link function (ex., while i.link Connecting appears in the display of STR-DA9000ES/TA-DA9000ES), the sound at the beginning of the track may be dropped out. 16 GB When the i.link indicator is lit No signal is output from all the other jacks (ANALOG 2CH OUT jacks, ANALOG 5.1CH OUT jacks, PHONES jack, DIGITAL (CD) OUT jacks). The D. FILTER, D. OUTPUT, 2CH SPK MODE, MCH SPK MODE, LEVEL ADJUST and SPK DISTANCE menu operations are not available.

17 Playing Discs Using the Display The display window shows various information about the disc or track being played. This section describes the current disc information and information that appears for each play status. TIME/TEXT MENU Disc information when a disc is loaded Depending on the disc that is currently loaded, the display shows as follows: 2 channel Super Audio CD 2 CH AMS> Multi-channel Super Audio CD MULTI 5.1CH or MULTI 5 CH or MULTI CH DISPLAY MODE TIME/TEXT During playback of a 5.1 channel Super Audio CD Conventional CD During playback of a 5 channel Super Audio CD During playback of other Super Audio CDs or during stop mode CD Displaying information while the player is stopped Press TIME/TEXT. The display shows the total number of tracks and total playing time. Total number of tracks Total playing time MULTI CH TRACK MIN SEC GB

18 Playing Discs Using the Display Displaying information while the player is playing Press TIME/TEXT. Each time you press the button, the current track number and its elapsed time or remaining time appears, or the total remaining time for the disc appears in the display. When the player detects a Multi-channel Super Audio CD, the channel information appears before the default display appears. Playing track number and elapsed playing time of the current track (default display) MULTI 5.1CH TRACK INDEX MIN SEC Press TIME/TEXT Playing track number and remaining time of the current track MULTI 5.1CH TRACK MIN SEC Press TIME/TEXT Total remaining time on the disc MULTI 5.1CH MIN SEC Press TIME/TEXT Channel information (appears only when the player detects a Multi-channel Super Audio CD) MULTI 5.1CH TRACK [MULTI] 5.1 CH Turning off the information in the display Z Each time you press DISPLAY MODE on the remote while playing a disc, the display turns off and on alternately. Even when the display is turned off, the display turns on if you pause or stop play. When you resume play, the display turns off again. Before you start playing, when you press DISPLAY MODE to turn off the display, Display Off appears, and when you press the button to turn on the display, Display On appears. Displaying the information of a TEXT disc TEXT discs contain information, such as the disc name or artist name, as well as the audio signals. This player can display the disc name, artist name, and current track name as TEXT information. When the player detects a TEXT disc, TEXT appears in the display. If your TEXT disc has several languages, MULTI-TEXT appears in the display. When you want to check the information in another language, see Displaying the information of a TEXT disc in other languages on page 19. Displaying the information of a TEXT disc in stop mode Press TIME/TEXT. Each time you press the button, the disc name or artist name appears in the display. When you select the artist name, ART. appears in the display. Before you start playing Disc title MULTI CH TEXT DISC SONYHITS Artist name ART. SONY BAND Press TIME/TEXT Press TIME/TEXT MULTI CH TEXT TRACK MIN SEC TEXT MULTI Total number of tracks and total playing time CH Press TIME/ TEXT 18 GB

19 Playing Discs Display information of a TEXT disc while playing a disc The current track name appears. If the disc name has more than 15 characters, the first 14 characters will remain after the name scrolls by in the display. When the player detects a Multi-channel Super Audio CD, the channel information appears before the playing time of the current track appears. While playing a disc Track title MULTI 5.1CH TEXT TRACK HITECHBLUES Press TIME/TEXT Channel information (appears only when the player detects a Multi-channel Super Audio CD) MULTI 5.1CH TEXT TRACK [MULTI] 5.1 CH Displaying the information of a TEXT disc in other languages You can change the displayed language if the TEXT disc has multi language capacity. When the player detects such a TEXT disc, MULTI-TEXT appears in the display. Change the language according to the procedures below. 1 Press MENU in stop mode. 2 Turn. AMS > until LANGUAGE appears in the display. 3 Press. AMS >. The current selected language (English, French, German, etc.) flashes. If the player cannot display the language used in a TEXT disc, Other lang appears in the display. 4 Turn. AMS > until the desired language appears in the display. 5 Press. AMS >. After a few seconds, the information appears in the selected language. Playing time of the current track MULTI 5.1CH TEXT TRACK INDEX MIN SEC Press TIME/TEXT Remaining time on the current track MULTI 5.1CH TEXT TRACK MIN SEC Press TIME/TEXT Remaining time on the disc MULTI 5.1CH TEXT MIN SEC Press TIME/ TEXT Notes The display may not show all the characters, depending on the disc. This player can display only the disc name, artist name, and track names from TEXT discs. Other information cannot be displayed. 19 GB

20 Playing Discs Locating a Specific Track During stop or play mode, you can locate any track to be played. Locating a Particular Point in a Track You can locate a particular point in a track during play or play pause. Number buttons H.AMS> >10.AMS>./> m/m INDEX >/../> To locate The next or succeeding tracks The current or preceding tracks A specific track directly You need to Turn. AMS > clockwise until you find the track. When using the remote, press > repeatedly until you find the track. Turn. AMS > counterclockwise until you find the track. When using the remote, press. repeatedly until you find the track. Turn. AMS > until you find the track number you want. When using the remote, press. or > repeatedly until you find the track. Locating a point while monitoring the sound (Search) Z Press and hold m/m during play. You will hear intermittent playback as the disc goes forward or reverses. When you reach the desired point, release the button. Locating a point by observing the time indication (High-Speed Search) Z Press and hold m/m during play pause. You will not hear the playback sound. z When Over!! appears in the display The disc has reached its end. Press. or m to go back. Locating a track directly by entering the track number Z Press the number button(s) to enter the track number. z To enter a track number over 11 Z 1 Press >10. 2 Enter the corresponding digits. To enter 0, press 10/0 instead. Examples: To play track number 30, press >10, then 3 and 10/0. To play track number 100, press >10 twice, then 1, and 10/0 twice. Note The default display reappears if you press >10 twice when the number of total tracks is less than 100. Note Tracks that are only a few seconds long may be too short for monitoring. In this case, the player may not search correctly. Locating a point using the index function (Index Search) Z Press INDEX. or INDEX> repeatedly in play or pause mode. z What is an INDEX? Some Super Audio CD or CD are provided with an index marking system which divides tracks or discs into smaller segments. This is especially useful when you want to locate a certain point within a long track (in classical music for example). The index search function works only when you use a commercially available indexed discs (usually indicated on the label). 20 GB

21 Playing Discs Locating a point by setting the start time (Time Search) 1 Press./> (or turn. AMS >) to select the desired track in stop mode. Playing Tracks Repeatedly Z You can play an entire disc or portions thereof repeatedly. This function can be used with Shuffle Play to repeat all the tracks in random order (page 22), or with Program Play to repeat all the tracks in a program (page 23). You can also repeat a specific track or portion within a track. 2 Press and hold m/m to set the time to start play while looking at the display. You can set the time from the beginning of the desired a track when you press M at first, and set the time from the end of the desired track backward s when you press m at first MULTI 5.1CH TRACK MIN SEC REPEAT AyB H x 3 Press H. Play will start at the time search. Note If you turn off the player or disconnect the mains lead, the player will store the last setting of repeat play ( Repeat All or Repeat 1 ) and recall it the next time you turn on the player. However, the setting of the Repeat A-B Play will be cancelled if you turn off the player or disconnect the mains lead. Repeating all the tracks on the disc (Repeat All Play) Press REPEAT once, then press H. Repeat appears in the display and Repeat All Play starts. The repeat play changes depending on the play mode you select. When the play mode is Normal play (page 16) Shuffle Play (page 22) Program Play (page 23) The player repeats All the tracks in sequence All the tracks in random order All the tracks in the program in sequence To cancel Repeat All Play Press REPEAT repeatedly until REPEAT goes off. 21 GB

22 Playing Discs Playing Tracks Repeatedly Z Repeating the current track (Repeat 1 Play) While the track you want to repeat is being played, press REPEAT repeatedly until REPEAT 1 appears in the display. Repeat 1 Play starts. Playing Tracks in Random Order (Shuffle Play) Z When you select Shuffle Play, the player plays all the tracks on the disc in random order. CONTINUE SHUFFLE To cancel Repeat 1 Play Press REPEAT repeatedly until REPEAT 1 goes off. Repeating a specific portion within a track (Repeat A-B Play) You can specify one portion within a track to be played repeatedly. Note that the portion that you specify must be within the boundaries of a single track. H./> 1 While the player is playing, press AyB at the starting point (point A) of the portion to be played repeatedly. REPEAT appears and A flashes in the display. 2 Continue playing the track (or press M) to locate the ending point (point B), then press AyB. REPEAT A-B appears and Repeat A-B Play starts. To cancel Repeat A-B Play Press REPEAT. z You can set a new starting point and ending point during Repeat A-B Play You can change the current ending point to a new starting point, then specify a new ending point to repeat another portion right after the current portion. 1 During Repeat A-B Play, press AyB. The current ending point changes to the new starting point (point A). REPEAT lights up and A flashes in the display. 2 Locate the new ending point (point B) and press AyB. REPEAT A-B lights up and the player starts to repeat the newly specified portion. When you want to restart from the starting point A, press H during AyB repeat. 1 Press SHUFFLE in stop mode. 2 Press H. Shuffle Play starts. ; appears while the player is shuffling the tracks. The player will stop after playing all the tracks once. To resume normal play Press CONTINUE. z You can locate tracks during Shuffle Play Press./>. Press > to locate the next track or press. to locate the beginning of the current track. The player does not go back to tracks which have already been played. Note When you change the playback area (2 channel/multi channel) or layer (CD/HD) of the Super Audio CD (page 15), Shuffle Play setting is cleared. 22 GB

23 Playing Discs Creating Your Own Program (Program Play) Z You can pick out the tracks that you like and specify the playback order in a program containing up to 32 tracks (or 999 min. 59 sec. in total program time). CONTINUE Number buttons PROGRAM Checking the contents of the program Before you start playing or while the player is playing, press CHECK. Each time you press the button, the track numbers will appear in the display in the programed order. When you press CHECK while the player is playing, the track number appears from the next track numbers of the current playing track number. Changing the contents of the program >10 CHECK H./> CLEAR You can change the contents of the program in stop mode. To Erase a track Erase from the last track in the program Do the following: 1 Press CHECK repeatedly until the track number you want to erase appears. 2 Press CLEAR. Press CLEAR. Each time you press the button, the last track of the program is erased. 1 Press PROGRAM in stop mode. Program appears in the display. 2 Press the number buttons to enter the track number. If you entered the wrong track number Press CLEAR to erase the track number and reenter the correct track number using the number buttons. To select a track number over 11 Press >10 (page 20). 3 Repeat step 2 to enter other tracks. Each time you enter a track number, the total program time appears in the display. 4 Press H. Program Play starts. Add a track to the end of the program Erase all tracks Press./> to select the track you want to add, then press PROGRAM. When using the remote, press the number button of the track to be added. Hold down CLEAR or x (for about 2 seconds) until Prog CLEAR appears in the display. To resume normal play Press CONTINUE. z The program remains even after Program Play ends Press H to play from the beginning of the program again. The program remains even if you stop play. Note If you turn off the player, disconnect the mains lead, press A OPEN/CLOSE, or change the playback area (2 channel/ mulch channel) or layer (CD/HD) of the Super Audio CD (page 15), the program will be erased. 23 GB

24 Playing Discs Listening to a CD Using a Filter (Digital Filter Function) This player is equipped with a digital filter that eliminates noise generated during sampling. By selecting type of filters, you can adjust the sound quality. You can select STANDARD or OPTION. (The default setting is STANDARD. ) When the i.link indicator is lit This function is not available. MENU.AMS> Setting the DIGITAL OUT on/ off You can set the digital out mode to on (the digital signals can be output) or off (the digital signals cannot be output). When you use the DIGITAL (CD) OUT COAXIAL or DIGITAL (CD) OUT OPTICAL connecter, set the digital mode to on ( D.OUT ON ). (The default setting is D.OUT ON. ) When the i.link indicator is lit This function is not available. MENU.AMS> 1 Press MENU. 2 Turn. AMS > until D. FILTER appears in the display. 3 Press. AMS >. 4 Turn. AMS > until desired filter name ( STANDARD or OPTION ) appears in the display. 5 Press. AMS >. When you select OPTION, FILTER appears in the display. Characteristics of each digital filter STANDARD Provides a wide frequency range and spatial feeling. 1 Press MENU. 2 Turn. AMS > until D. OUTPUT appears in the display. 3 Press. AMS >. 4 Turn. AMS > until desired digital mode ( D.OUT ON or D.OUT OFF ) appears in the display. 5 Press. AMS >. Note When you play a Super Audio CD, this function does not work and no signal is output from the DIGITAL (CD) OUT connectors. OPTION Provides smooth and powerful sound with clear image position. Notes Digital filters are effective only when you play a conventional CD. You cannot select the digital filter when you play a Super Audio CD. According to the disc or connected equipment, there may be no noticeable effect after switching the filter. 24 GB

25 Playing Discs Listening to a Multichannel Super Audio CD (Multi-channel management function) This player is equipped with a Multi-channel management function that sets the playback mode of the Super Audio CD by the DSD-DSP (built into the player) according to the layout or size of your speaker. When the i.link indicator is lit This function is not available. Selecting 2 channel playback mode 1 Press MENU. 2 Turn. AMS > until 2CH SPK MODE appears in the display. 3 Press. AMS >. The playback mode appears in the display. Example of the speaker layout Playback mode Front speakers Sub woofer Front speakers L R 2CH Direct 2CH + SW Each signal outputs directly from front speakers. No signal outputs from the Sub woofer. a a Surround speakers MENU L Sub woofer Center speaker To set the Multi-channel management: 1 Select the appropriate preset playback mode (2 channel playback or Multi-channel playback). 2 Adjust the output level balance of each speaker (only when you select the Multi-channel playback mode). Notes This features only work when you play a Super Audio CD. You may not be able to adjust the output level balance depending on the speaker layout mode that you selected. R.AMS> 4 Turn. AMS > until desired mode appears in the display. 5 Press. AMS >. Note You cannot operate this function when the player is in the CD or Multi-channel playback mode. Operate this function when the player is in the 2 channel Super Audio CD playback mode, the disc tray is opened, or no discs are in the player. Selecting Multi-channel playback mode 1 Press MENU. 2 Turn. AMS > until MCH SPK MODE appears in the display. 3 Press. AMS >. The playback mode appears in the display. Playback mode MCH Direct Front speakers Center speaker Surround speakers Sub woofer Each signal outputs directly from each speaker. 5 Large + SW Large Large Large a 5 Large Large Large Large 5 Small + SW Small Small Small a FRT Large +SW Large Small Small a FRT Large Large Small Small No CNTR + SW Large Large a No CNTR Large Large ENTER LEVEL ADJ./> 25 GB

26 Playing Discs Listening to the Multi-channel Super Audio CD About Large or Small speaker A Large speaker is a speaker that can reproduce bass frequencies plentifully. If you select Small for the surround speakers, the bass frequencies will come from the front speakers and/or sub woofer. For normal use, select MCH Direct or set all the speakers to Large (ex. 5 Large + SW, 5 Large, etc.). If the sound is noisy or the Multi-channel playback is not effective while playing a Multi-channel Super Audio CD, change the settings of the speakers concerned to Small. 4 Turn. AMS > until desired mode appears in the display. 5 Press. AMS >. To return to the normal display, press MENU. Notes The Multi-channel management function does not work when you select MCH Direct (you cannot set the output level balance of each speaker). The front speaker setting is set to Large automatically when you set the Sub woofer to. When you play a track that does not contain the LFE* signal, the signal for the Sub woofer does not output. Therefore, when you select MCH Direct, 5 Large + SW, or No CNTR + SW, no signal outputs from the Sub woofer. However, when you select 5 Small + SW or FRT Large +SW (when you set the speaker setting to Small ), the bass frequencies will come from the sub woofer. * Low Frequency Enhancement (described as.1 CH ) Adjusting the output level balance of each speaker You can adjust following items with the Multi-channel management function: CNTR BALANCE The relative output level balance between the front speakers (FRONT L/R) and the center speaker (CENTER) SURR BALANCE The relative output level balance between the front speakers (FRONT L/R) and the surround speakers (SURR L/R) SW BALANCE The relative output level balance between the front speakers (FRONT L/R) and the sub woofer (SUB WOOFER) Note Some adjustment may not work depending on the Multi-channel playback mode that you selected. Adjusting the output level balance on the front panel of the player You can adjust the output level balance of each speaker while listening during playback. You can also adjust while listening to the test tone during stop mode. 1 Press MENU. 2 Turn. AMS > until LEVEL ADJUST appears in the display. 3 Press. AMS >. During playback, go to Step 6. 4 Turn. AMS > until TONE ON appears in the display. 5 Press. AMS >. The test tone issues from the speakers in sequence with the speaker type appearing in the display. 6 Turn. AMS > until the desired item appears in the display. Select the item from CNTR BALANCE, SURR BALANCE, or SW BALANCE. Note When you set the Sub woofer to in the Multi-channel playback mode (page 25), SW BALANCE does not appear. Similarly, CNTR BALANCE or SURR BALANCE does not appear when you set the corresponding speaker to. 26 GB

27 Playing Discs 7 Press. AMS >. The balance adjustment display appears. In stop mode, the test tone is output from the selected speaker. Example: When you select SURR BALANCE during stop mode, the test tone is output from the front speakers and surround speakers. 5 Press ENTER. The balance adjustment display appears. In stop mode, the test tone is output from the selected speaker. Example: When you select SURR BALANCE during stop mode, the test tone is output from the front speakers and surround speakers. MULTI CH DISC FRT: :SURR 8 Turn. AMS > to adjust the output level. MULTI CH DISC FRT: :SURR 6 Press./> repeatedly to adjust the output level. MULTI CH DISC FRT: :SURR 9 Press. AMS >. The player status returns to Step 6. Repeat Step 6 through 9 for more adjustments. 10 Press MENU after you finish adjusting. The display returns to the normal display. Adjusting the output level from the remote Z You can adjust the output level of each speaker from the listening position by using the supplied remote. 1 Press LEVEL ADJ during playback or stop mode. During playback, go to Step 4. 2 Press./> repeatedly until TONE ON appears in the display. 3 Press ENTER. The test tone issues from the speakers in sequence with the speaker type appearing in the display. 4 Press./> repeatedly until the desired item appears in the display. Select the item from CNTR BALANCE, SURR BALANCE, or SW BALANCE. Note When you set the Sub woofer to in the Multi-channel playback mode (page 25), SW BALANCE does not appear. Similarly, CNTR BALANCE or SURR BALANCE does not appear when you set the corresponding speaker to. MULTI CH DISC FRT: :SURR 7 Press ENTER. The player status returns to Step 4. Repeat Step 4 through 7 for more adjustments. 8 Press LEVEL ADJ after you finish adjusting. The display returns to the normal display. Note If you select a playback mode other than 2CH Direct or MCH Direct using the Multi-channel management function, the sound distribution to the speakers will change, possibly causing a decrease in overall sound volume. If this occurs, adjust the volume with the volume control on the connected amplifier. 27 GB

28 Playing Discs Listening to the Multi-channel Super Audio CD Adjusting the speaker distance You can adjust the speaker distance when the connected amplifier does not have the setting menu for speaker distance. If the amplifier has this function, we recommend that you set the speaker distance on the amplifier. This setting is available only for the Multi-Channel Super Audio CD. Note When you set the speaker distance on this player and the amplifier, both of the setting may work and you may not be able to get the proper result. FRT DIST. The distance from your listening position to the front speakers You can adjust from 1.0 meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot) steps. If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. SURR DIST. The distance from your listening position to the surround speakers You can adjust from 1.0 meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot) steps. If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. CNTR DIST. The distance from your listening position to the center speaker You can adjust from 1.0 meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot) steps. SUBW DIST. The distance from your listening position to the sub woofer You can adjust from 1.0 meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot) steps. DIST. UNIT The unit of measure for setting distances (meter or feet) The initial setting is feet for the North American model and meter for the European model. Note Speaker distance cannot be adjusted in the following cases. When the player is reading the disc information of CD (or the CD area of Super Audio CD) When the player is reading the 2 channel area of Super Audio CD When the i.link indicator is lit 1 Press MENU. 2 Turn. AMS > until SPK DISTANCE appears in the display. 3 Press. AMS >. 4 Turn. AMS > until the desired item appears in the display. Select the item from FRT DIST., SURR DIST., CNTR DIST. or SUBW DIST. Note When you set the Sub woofer to in the Multi-channel playback mode (page 25), SUBW DIST. cannot be adjusted ( Not In Use appears). Similarly, CNTR DIST. cannot be adjusted ( Not In Use appears) when you set the corresponding speaker to. 5 Press. AMS >. The speaker distance adjustment display appears. Example: When you select SURR DIST. (with DIST. UNIT set to meter ). MULTI CH DISC SURR 3.0meter 6 Turn. AMS > to adjust the speaker distance. MULTI CH DISC SURR 2.5meter 7 Press. AMS >. The player status returns to Step 4. Repeat Step 4 through 7 for more adjustments. 8 Press MENU after you finish adjusting. The display returns to the normal display. Selecting the distance unit In Step 4 above, select DIST. UNIT. Turn. AMS > to select meter or feet, then press. AMS >. Setting speaker distances back to the default Set all speaker distances to 3 meters (10 feet). 28 GB