安装定位设备至 Pimax 4K Install positional suite to Pimax 4K 1 如下图 1 所示将定位器支架粘贴在 Pimax 4K VR 正中间部位 ( 如下图 2) 安装过程中注意定位器支架不要把 Pimax 的灯给覆盖掉 a.see Figure 1, stic

Size: px

Start display at page:

Download "安装定位设备至 Pimax 4K Install positional suite to Pimax 4K 1 如下图 1 所示将定位器支架粘贴在 Pimax 4K VR 正中间部位 ( 如下图 2) 安装过程中注意定位器支架不要把 Pimax 的灯给覆盖掉 a.see Figure 1, stic"

礼平
6 years ago
Views:

1 Pimax VR 配合 Nolo 定位套装使用教程 Tutorial of combining Pimax VR with Nolo positional suite 步骤引导 : 1. 认识 Nolo 2. 安装定位设备至 Pimax 4K 3. 配对 Nolo 定位设备 4. 安装最新版 Piplay 并连接电脑 5. 进行游戏体验 6. 使用注意点及常用快捷按键 Steps: 1. Nolo presentation 2. Install positional suite to Pimax 4K 3. Nolo positional suite pairing 4. Install the latest Piplay and connect to PC 5. Experience VR games 6. Tips and common shortcut buttons 认识 Nolo Nolo presentation 每一套 NOLO 产品都包含有 :1 个定位基站 1 个头盔定位器 2 个交互手柄 2 个不同形状的头盔定位器卡座 1 条 OTG 线 1 条 4 米的 USB 线 1 条一分三的 USB 线 1 个充电插头 2 根手绳 One suite of Nolo includes: 1 Base station, 1 Headset marker, 2 interactive controllers, 2 different headset marker mounts, 1 USB OTG cable, 1 USB cable of 4 meters, 1 3-in-1 USB charging cable, 1 wall charger and 2 wrist straps.

2 安装定位设备至 Pimax 4K Install positional suite to Pimax 4K 1 如下图 1 所示将定位器支架粘贴在 Pimax 4K VR 正中间部位 ( 如下图 2) 安装过程中注意定位器支架不要把 Pimax 的灯给覆盖掉 a.see Figure 1, stick the headset marker mount on the middle of Pimax 4K VR(see Figure 2), please do not cover the indicator led of Pimax. 2 如下图 3 所示, 把 Nolo 头部定位器装至支架上, 并使用用 4 米长的 USB 线连接电脑 USB 口与定位器 b. See Figure 3, Mount the headset marker, and connect that USB cable of 4 meters between a USB port of PC and headset marker. 3 玩家可以使用胶布或者卡扣把 Nolo 定位器的线与 Pimax 的线固定在一起, 防止拉扯 ( 如下图 4) c. You could use rubberized fabric or clips to fasten Nolo and Pimax's cables together, avoiding stumble.

3 配对 Nolo 定位设备 Match Nolo positional suite 注意 : 配对 Nolo 定位器的设备需要把基站手柄定位器全部开机后进行 ( 定位器 USB 连接电脑供电即可 ) Notes: It needs to start Base station, Controllers, Headset marker. (Headset marker should connect to PC) 配对的原理为 : 长按基站的配对键进入配对模式后, 分别单独按住手柄与定位器的配对按键进行关闭, 再短按基站配对键退出配对模式后, 配对才能完成具体操作步骤如下 : Pairing principle: Press & hold the pair button of Base station and enter into pairing mode, separately hold pair buttons of controllers and the marker to close, and then click the pair button of Base station to quit the pairing mode, finally finish this pairing. Steps as below: 第一步 : 打开定位基站手柄, 并将头盔定位器与电脑连接 Step 1 Start Base station and Controllers, and connect headset marker to PC. 第二步 : 长按定位基站后面的配对键, 直到定位基站停止运作并进入配对模式 Step 2 Press & Hold the pair button on the back of the Base station until it

button (Indicator lighter extinguishes or vibrate s once to pair (one by one) 第四步 : 长按头盔定位器上的配对键, 直到 LED

4 stops and enter into pair mode. 第三步 : 分别长按手柄旁边的配对键 ( 指示灯熄灭或者震动一次 ), 进行手柄配对 ( 轮流配对 2 个手柄 ) Step 3 Separately press & hold the sideward pair button (Indicator lighter extinguishes or vibrate s once to pair (one by one) 第四步 : 长按头盔定位器上的配对键, 直到 LED 灯闪烁一次, 进行定位器配对 Step 4 Press & hold the pair button of Headset marker until the LED lighter blinked once, and then pair. 第五步 : 单击定位基站后面的配对键来结束配对, 等待 3-5 秒, 如果所有 LED 灯都转为绿色, 则配对成功, 否则请重复以上步骤 Step 5, Press the pair button at the back of Base station to end the pairing, it is successful if all LED lighters turn green after waiting 3 5 seconds. Or else, please redo operations above. 安装最新版 Piplay 并连接电脑

Install the latest Piplay and connect to PC 下载安装最新版本的 1.2.89 版本 Download the latest Piplay version 1.2.89 下载地址 : 百度云 :http://pan.baidu.com/s/1sksz2i5 Downloading link: http://www.

For better match positional controllers of Nolo, the firmware would be forcedly upgraded to the version 1.0.0.265 after installed this Piplay version.

5 Install the latest Piplay and connect to PC 下载安装最新版本的版本 Download the latest Piplay version 下载地址 : 百度云 : Downloading link: 注意 : 1. 为配合 Nolo 定位手柄使用, 安装该版本 Piplay 后固件会强制升级为版本, 如果固件低于该版本用户, 会提示固件升级部分用户由于缺少 DFU 驱动会导致升级无法成功, 此时下载驱动精灵软件, 安装 DFU 驱动后等待几分钟即可自动升级成功 Notes: a. For better match positional controllers of Nolo, the firmware would be forcedly upgraded to the version after installed this Piplay version. The tips of upgrading firmware would pop up if it s lower. This upgrade may be unsuccessfully if PC lacks DFU driver. (Downloading link:

6 2. 该版本集成了 Nolo 驱动, 请不要同时安装 Nolo 驱动与该版本 Piplay 以免产生冲突, 如果已安装 Nolo 驱动, 使用 Piplay 时请关闭 Nolo 相关驱动即可 b. This Piplay version build-in Nolo driver. Pleases do disable Nolo driver to avoid conflict if you installed Nolo driver at the same when you re using Piplay driver. Pimax 4K VR 与 Nolo 连接电脑介绍如下 : 设备与电脑连接情况 Pimax4KVR USB 与 HDMI 线均需连接电脑 Nolo 定位器使用 4 米的 USB 线连接电脑 Nolo 手柄无需用线连接电脑 Nolo 基站无需用线连接电脑 ( 可以边充电边使用 ) Introduction of connecting Pimax 4K VR and Nolo to PC Devices Pimax 4K VR Nolo Marker Nolo Controllers Nolo Base Station Connection USB & HDMI cable should be connected to PC Connect the USB cable of 4 meters to PC No need cable No need cable (it could be using when it s charging 进行游戏体验 Experience VR games 正常连接 Piplay 后, 打开 Steam VR 与 Nolo 定位设备,Steam VR 就会设别到 2 个手柄与 1 个基站, 如下图所示 : Open SteamVR and Nolo after run Piplay normally, and then SteamVR will recognize the base station and 2 controllers, see Figure below: 此时, 即可进行 VR 定位游戏的体验 This moment, we can experience positional VR games. 连接 Nolo 定位器 USB 后 Piplay 会自动断开重新连接, 并切换为定位状态

7 Piplay will reconnect after connecting Nolo marker through that USB cable, and then it will switch to the positional state. 移除 Nolo 定位器的 USB 后 Piplay 会自动断开重新连接, 并切换为普通状态 Piplay will reconnect after removing that USB cable of Nolo marker, and then it will swtich to the normal state 推荐体验游戏 : Audioshield 音盾 VR 版节奏大师跟随音乐一起摇摆 Tilt Brush 空间绘画画出无限可能 VR KANOJO VR 女友你有一个女朋友请开门接收 Serious Sam VR 英雄萨姆系列打出一片天 theblu 深蓝体验神奇的海底世界 Google Earth VR 谷歌地球世界这么大现在就去看看 Recommended VR games: 1. Audioshield 2. Tilt Brush 3. VR KANOJO 4. Serious Sam VR 5. TheBlu 6. Google Earth VR 使用注意点及常用快捷按键 Tips and common shortcut buttons 基站的位置摆放注意 : Notes for putting Base station 错误的摆放 : 定位基站请不要摆放在台面太靠里边, 如此摆放会遮挡掉一大部分基站的激光, 导致连接不稳定及丢失信号, 如下为错误摆放 : Wrong: Please do not put it inside the table, which may cover most of laser from Base station and cause that signal is not stable or lost, see Figure below:

效果正确的摆放 : 定位基站请摆放在台面的边沿初, 可以保证基站激光不被遮挡, 保证定位

Recommend put: Put it equivalent to the height

8 效果正确的摆放 : 定位基站请摆放在台面的边沿初, 可以保证基站激光不被遮挡, 保证定位 Right: Put it on the edge of table for better positional effect. 推荐高度摆放 : 定位基站摆放的高度推荐为与肩齐高的位置, 并保证范围空旷, 不要被物体遮挡 Recommend put: Put it equivalent to the height of shoulder, and do not cover it. 校准正方向 : 头部定位器与手柄正对基站, 双击手柄系统键 (2 个圆圈 ), 可以一键重

置正方向, 并且重置手柄位置 Calibrate positive direction: Headset marker and Controllers face to Base station, double-click system button of controllers (see the circle in Figure

校准地面高度 : 小派 4KVR 及定位器放置地面并正对基站 ( 确保基站能够照到定位器 ), 单击定位器配对键, 可以一键设置地面高度 Calibrate the height of ground level: Put Pimax 4K VR and the marker facing Base station (the

9 置正方向, 并且重置手柄位置 Calibrate positive direction: Headset marker and Controllers face to Base station, double-click system button of controllers (see the circle in Figure below), which can achieve push-button reset positive direction and virtual controllers postion. 校准地面高度 : 小派 4KVR 及定位器放置地面并正对基站 ( 确保基站能够照到定位器 ), 单击定位器配对键, 可以一键设置地面高度 Calibrate the height of ground level: Put Pimax 4K VR and the marker facing Base station (the marker should be covered by Base station), click the pair button of the marker, and then set the ground level. 一键转身 : 双击手柄的菜单键, 可以一键转身 180 度 One push-button turn-back: double-click the menu button of controller to achieve 180 degree turn-back.

视频教程 : 教程地址 :https://v.qq.com/x/page/p0521mmk3nv.

10 视频教程 : 教程地址 : 使用视频 :

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact