Microsoft Word PT46.doc

Size: px
Start display at page:

Download "Microsoft Word PT46.doc"

Transcription

1 PT46

2 ENGLISH Thank you for choosing Delta DVP series PLC. DVP04PT-S is able to receive 4 points of platinum temperature sensors and convert them into 16-bit digital signals. Besides, through FROM/TO instructions in DVP Slim series MPU program, the data in DVP04PT-S can be read and written. There are many 16-bit control registers (CR) in DVP04PT-S. The power unit is separate from it and is small in size and easy to install. EN DVP04PT-S is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity, electric shock and vibration. To prevent non-maintenance staff from operating DVP04PT-S, or to prevent an accident from damaging DVP04PT-S, the control cabinet in which DVP04PT-S is installed should be equipped with a safeguard. For example, the control cabinet in which DVP04PT-S is installed can be unlocked with a special tool or key. EN DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring again before DVP04PT-S is powered up. After DVP04PT-S is disconnected, Do NOT touch any terminals in a minute. Make sure that the ground terminal on DVP04PT-S is correctly grounded in order to prevent electromagnetic interference. FR DVP04PT-S est un module OUVERT. Il doit être installé que dans une enceinte protectrice (boitier, armoire, etc.) saine, dépourvue de poussière, d humidité, de vibrations et hors d atteinte des chocs électriques. La protection doit éviter que les personnes non habilitées à la maintenance puissent accéder à l appareil (par exemple, une clé ou un outil doivent être nécessaire pour ouvrir a protection). FR Ne pas appliquer la tension secteur sur les bornes d entrées/sorties, ou l appareil DVP04PT-S pourra être endommagé. Merci de vérifier encore une fois le câblage avant la mise sous tension du DVP04PT-S. Lors de la déconnection de l appareil, ne pas toucher les connecteurs dans la minute suivante. Vérifier que la terre est bien reliée au connecteur de terre afin d éviter toute interférence électromagnétique. Product Profile & Dimension I+ I+ I+ C H 1 C H 2 C H C H I [ Figure 1 ] Unit: mm 1. Status indicator (POWER, RUN and ERROR) 8. I/O module connection port 2. Model name 9. I/O module clip 3. DIN rail clip 10. DIN rail (35mm) 4. I/O terminals 11. RS-485 communication port 5. I/O point indicator 12. I/O module clip 6. Mounting holes 13. DC power input - 1 -

3 7. Specification label 14. I/O module connection port I/O Terminal Layout DVP04PT-S CH1 Ch2 Ch3 Ch4 I- I- I- I- External Wiring 3- wi re PT100 Shielded cable *1 CH 1 I mA PT10 00 Shielded cable *1 CH mA 2- wi re I- 5V *2 Terminal of the power module +15V * DC / DC System 24 - Grounding -15V Class 3 Grounding (Below 100 ) Note1: Use only the wires that are packed with the temperature sensor for analog input and separate from other power line or any wire that may cause noise. Note2: Terminal is grounded for noise suppression. Note3: Please connect power supply module terminal and DVP04PT-S temperature measurement module terminal to system earth ground. Warning: DO NOT connect wires to the No Connection terminals. Electrical Specifications Power supply voltage 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) Max. rated power 2W, supplied by external power. consumption Operation: 0 C~55 C (temp.), 5~95% (humidity), pollution degree 2 Operation/storage Storage: -25 C~70 C (temp.), 5~95% (humidity) Vibration/shock International standards: IEC , IEC (TEST Fc)/ resistance IEC & IEC (TEST Ea) The modules are numbered from 0 to 7 automatically by their distance Series connection to from MPU. No.0 is the closest to MPU and No.7 is the furthest. DVP-PLC MPU Maximum 8 modules are allowed to connect to MPU and will not occupy any digital I/O points. Functional Specifications DVP04PT-S Celsius ( C) Fahrenheit ( F) Analog input channel 4 channels per module Sensors type 2-wire/3-wire PT100/ Ni100/ PT1000/ Ni PPM/ C (DIN JIS C ) Current excitation 1.53mA / 204.8uA Temperature input range Please refer to the temperature/digital value characteristic curve. Digital conversion range Please refer to the temperature/digital value characteristic curve. Resolution 16 bits (0.1 C) 16 bits (0.1 F) Overall accuracy 0.6% of full scale during 0 ~ 55 C (32 ~ 131 F) Response time 200ms channels Isolation between digital and analog circuitry. There is no isolation Isolation method between channels. 500VDC between digital circuits and Ground 500VDC between analog circuits and Ground Isolation method 500VDC between analog circuits and digital circuits 500VDC between 24VDC and Ground

4 DVP04PT-S Celsius ( C) Fahrenheit ( F) Digital data format 2 s complement of 16-bit Average function Yes (CR#2 ~ CR#5) Self diagnostic function Yes Communication mode (RS-485) Yes (CR#32). RS-485 is disabled when the DVP04PT-S is connected in series with an MPU. Control Register CR# Address Save Register content Description #0 H 4064 O R Model name Set up by the system: DVP04PT model code = H 8A. CH1 mode: b0 ~ b3 CH2 mode: b4 ~ b7 CH3 mode: b8 ~ b11 CH4 mode: b12 ~ b15 Take CH1 mode (b3,b2,b1,b0) for #1 H 4065 O R/W Mode setting example. The default value is H (0,0,0,0): PT (0,0,0,1): NI (0,0,1,0): PT (0,0,1,1): NI (1,1,1,1): The channel is disabled. #2 H 4066 O R/W CH1 average number Number piece of readings used for the #3 H 4067 O R/W CH2 average number calculation of average temperature on channels CH1 ~ CH4. Setting range: #4 H 4068 O R/W CH3 average number For versions prior to V3.04: K1 ~ K4,095. For versions after V3.05: K1 ~ K20. #5 H 4069 O R/W CH4 average number Default setting is K10. #6 H 406A X R CH1 average degrees Average degrees for channels CH1 ~ #7 H 406B X R CH2 average degrees CH4. #8 H 406C X R CH3 average degrees (Unit: 0.1 C). #9 H 406D X R CH4 average degrees #12 H 4070 X R CH1 average degrees #13 H 4071 X R CH2 average degrees #14 H 4072 X R CH3 average degrees #15 H 4073 X R CH4 average degrees #18 H 4076 X R Present temp. of CH1 #19 H 4077 X R Present temp. of CH2 #20 H 4078 X R Present temp. of CH3 #21 H 4079 X R Present temp. of CH4 #24 H 407C X R Present temp. of CH1 #25 H 407D X R Present temp. of CH2 #26 H 407E X R Present temp. of CH3 #27 H 407F X R Present temp. of CH4 #29 H 4081 X R/W PID mode setting #30 H 4082 X R Error status #31 H 4083 O R/W Communication address setting #32 H 4084 O R/W #32 H 4084 O R/W #32 H 4084 O R/W Communication baud rate setting Communication baud rate setting Communication baud rate setting Average degrees for channels CH1 ~ CH4. (Unit: 0.1 F). Present temperature of channels CH1 ~ CH4. (Unit: 0.1 C). Present temperature of channels CH1 ~ CH4. (Unit: 0.1 F). Set H'5678 to enable PID mode, other set values are invalid. Default: H Data register stores the error status. Refer to the error code chart for details. RS-485 communication address. Setting range is 01 ~ 254 and default setting is K1. Communication baud rate. For ASCII mode, date format is 7 bits, even, 1 stop bit (7, E, 1), while RTU mode, date format is 8 bits, even, 1 stop bit (8, E, 1). b0: 4,800 bps (bit/sec). b1: 9,600 bps (bit/sec). (default setting) b2: 19,200 bps (bit/sec). b3: 38,400 bps (bit/sec). b4: bps (bit/sec). b5: 115,200 bps (bit/sec). b6 ~ b13: Reserved. b14: switch between low bit and high bit of CRC code (RTU mode only). b15: RTU mode

5 CR# Address Save Register content Description b15~b12 b11~ b9 b8~b6 b5~b3 b2~b0 ERR LED CH4 CH3 CH2 CH1 #33 H 4085 O R/W Reset to default setting #34 H 4086 O R Software version Example: Setting of CH1 1. b0 ~ b1: Reserved. 2. b2: Set to 1 and PLC will be reset to default settings. Definition of ERR LED: b12~b15=1111 (default settings) 1. b12 corresponds to CH1: when b12=1, scale exceeds the range, ERR LED flashes. 2. b13 corresponds to CH2: when b13=1, scale exceeds the range, ERR LED flashes. 3. b14 corresponds to CH3: when b14=1, scale exceeds the range, ERR LED flashes. 4. b15 corresponds to CH4: when b15=1, scale exceeds the range, ERR LED flashes. Display the software version in hexadecimal. ex: H 010A = version 1.0A #35 ~ #48 System used Symbols: O: means latched. X: means not latched. (Support when using RS-485 communication, not support when connecting with MPU) R: able to read data by using FROM instruction or RS-485. W: able to write data by using TO instruction or RS Function code: 03 H - read data from register. 06 H - write one word to register. 10 H - write multiple words to registers. 2. CR#30 is the error code register. Refer to the chart below: Error description Content b15- b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 b12 Power source abnormal K1 (H 1) The contact is not connected to anything. K2 (H 2) Hardware malfunction K16 (H 10) Average times setting error K64 (H 40) Instruction error K128 (H 80) The contact of CH1 is not connected to anything. (Abnormal conversion) The contact of CH2 is not connected to anything. (Abnormal conversion) The contact of CH3 is not connected to anything. (Abnormal conversion) The contact of CH4 is not connected to anything. (Abnormal conversion) K256 (H 100) K512 (H 200) K1024 (H 400) K2048 (H 800) Reserved Note: Each error code will have corresponding bit (b0 ~ b7). Two or more errors may happen at the same time. 0 means normal and 1 means having error

6 3. When CR#29 is set to H 5678, CR#0 ~ CR#34 can be used for PID settings in DVP04PT-S V3.08 and versions above. PID Mode Content Description CR#0 Model name CR#22 CH4 K I CR#2 PID output % at CH1 CR#24 CH1 K D CR#3 PID output % at CH2 CR#25 CH2 K D CR#4 PID output % at CH3 CR#26 CH3 K D CR#5 PID output % at CH4 CR#27 CH4 K D CR#2~CR#5: 0~1000; Unit: 0.1% Run/Stop & Auto tuning CR#6 CH1 average degrees ( C) Bit0: CH1 PID runs/stops CR#7 CH2 average degrees ( C) Bit1: CH2 PID runs/stops CR#8 CH3 average degrees ( C) Bit2: CH3 PID runs/stops CR#9 CH4 average degrees ( C) Bit3: CH4 PID runs/stops CR#6~CR#9: Unit: 0.1 C 0=PID stops; 1=PID runs CR#10 Set temperature at CH1 CR#28 Bit4: CH1 auto tuning CR#11 Set temperature at CH2 Bit5: CH2 auto tuning CR#12 Set temperature at CH3 Bit6: CH3 auto tuning CR#13 Set temperature at CH4 Bit7: CH4 auto tuning CR#10~CR#13: Set the PID target value (SV) CR#14 CH1 K P CR#29 1: The auto tuning function is enabled. After the auto tuning is complete, the value becomes 0. Enter the PID mode(h 5678) K0: Exit the PID mode CR#15 CH2 K P CR#30 Error Code CR#16 CH3 K P CR#31 CH1 sampling time CR#17 CH4 K P CR#32 CH2 sampling time CR#19 CH1 K I CR#33 CH3 sampling time CR#20 CH2 K I CR#34 CH4 sampling time CR#21 CH3 K I CR#31~CR#34: 1~30; Unit: 1s Note: Users have to enter the PID mode (CR#29= H 5678) before setting other control registers. Temperature/Digital Value Characteristic Curve The mode of measuring Celsius (Fahrenheit) temperature: Digital output Max. Min. Max. Temperature input Min. Platinum Temperature range Digital value conversion range resistor C (Min./Max.) F (Min./Max.) C (Min./Max.) F (Min./Max.) PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,380 PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,

7 繁體中文 感謝您採用台達 DVP 系列產品 DVP04PT-S 溫度量測模組可接受外部 4 點鉑金屬溫度感測器, 將之轉換成 16 位元之數位信號 透過 DVP-PLC SS/ SA/SX/SC/SV 主機程式以指令 FROM/TO 來讀寫模組內之資料, 模組內具有多個 CR (Control Register) 暫存器, 每個暫存器有 16 bits 電源單元與模組分離, 體積小, 安裝容易 請在使用之前, 詳細閱讀本使用說明書 實施配線, 務必關閉電源 上電時請勿接觸機體端子或進行維修 輸入電源切斷後, 一分鐘之內, 請勿觸摸內部電路 本機為開放型 (OPEN TYPE) 機殼, 因此使用者使用本機時, 必須將之安裝於具防塵 防潮及免於電擊 衝擊意外之外殼配線箱內 另必須具備保護措施 ( 如 : 特殊之工具或鑰匙才可打開 ) 防止非維護人員操作或意外衝擊本體, 造成危險及損壞 交流輸入電源不可連接於輸入 出信號端, 否則可能造成嚴重的損壞, 因此請在上電之前再次確認電源配線 本體上之接地端子務必正確的接地, 可提高產品抗雜訊能力 由測溫體到溫調本體的配線路請用最短距離配線, 為了避免雜訊及誘導的影響儘可能將電源線和負載配線分開 產品外觀尺寸與部位介紹 詳細部位指示圖與外觀尺寸請參閱英文版頁碼 1 之 [Figure1], 單位 :mm 1. 電源 錯誤及運行指示燈 6. I/O 模組定位孔 11. RS-485 通訊口 2. 機種型號 7. 銘牌 12. I/O 模組固定槽 3. DIN 軌固定扣 8. I/O 模組連接口 13. 電源輸入口 4. 端子 9. I/O 模組固定扣 14. I/O 模組連接口 5. 端子配置 10. DIN 軌糟 (35mm) 輸入 輸出端子台配置 請參閱英文版頁碼 2 之端子台配置示意圖 外部配線 3-wire PT100 隔離線 *1 CH1 I- 1.53mA PT1000 隔離線 *1 CH4 2-wire I- *2 接至電源模組之端 *3 24+ 系統接地點 24- 第三種接地 ( 接地抗阻 100 以下 ) DC/ DC 轉換器 mA 5V +15V -15V 註 1: 使用於類比輸入的配線應採用溫度感測器之連接線或雙絞隔離線且應與其他電源線或可能引起雜訊之接線分開 註 2: 如果雜訊過大請將 及接地端子連接 註 3: 請將電源模組之端及 DVP04PT-S 溫度量測模組之端連接到系統接地點, 再將系統接點作第三種接地或接到配電箱之機殼上 注意 : 空端子請勿配線 - 6 -

8 電氣規格 電源電壓 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) 額定最大消耗功率 操作 儲存環境 耐振動 衝擊 與 DVP-PLC 主機串接說明 2W, 由外部電源供應 1. 操作 :0 C ~ 55 C( 溫度 ),5 ~ 95%( 濕度 ), 污染等級 2 2. 儲存 :-25 C ~ 70 C( 溫度 ),5 ~ 95%( 濕度 ) 國際標準規範 IEC , IEC (TEST Fc)/IEC & IEC (TEST Ea) 模組編號以靠近主機之順序自動編號由 0 到 7, 最大可連接 8 台且不佔用數位 I/O 點數 功能規格 DVP04PT-S 攝氏 ( C) 華氏 ( F) 類比訊號輸入通道 適合感應器形式 驅動電流 輸入溫度範圍 數位轉換範圍 4 通道 台 2 線 /3 線 PT100/ Ni100/ PT1000/ Ni PPM/ C (DIN JIS C ) 1.53mA / 204.8uA 請參閱溫度 數位特性曲線附表 請參閱溫度 數位特性曲線附表 解析度 16 bits (0.1 C) 16 bits (0.1 F) 總和精密度 響應時間 隔離方式 數位資料格式 平均功能 自我診斷功能 0.6% 在 (0 ~ 55 C, 32 ~ 131 F) 範圍內滿刻度時 200ms 通道數 數位區與類比區有隔離, 通道間未隔離 數位電路與接地之間 :500VDC 類比電路與接地之間 :500VDC 類比電路與數位電路之間 :500VDC 24VDC 與接地之間 :500VDC 16 位元二補數 有 (CR#2 ~ CR#5) 上下極限偵測 / 通道 通訊模式 (RS-485) 有 (CR#32) 當與 PLC 主機串接時,RS-485 通訊無法使用 控制暫存器 (CR) CR# 參數位址 保持型暫存器名稱說明 #0 H 4064 O R 機種型號系統內定,DVP04PT-S 機種編碼 = H 8A #1 H 4065 O R/W 模式設定 CH1 模式 :b0 ~ b3 CH2 模式 :b4 ~ b7 CH3 模式 :b8 ~ b11 CH4 模式 :b12 ~ b15 以 CH1 設定 (b3,b2,b1,b0) 說明, 預設值 H 0000: 1. 設為 (0,0,0,0) 時, 選用 PT 設為 (0,0,0,1) 時, 選用 NI 設為 (0,0,1,0) 時, 選用 PT 設為 (0,0,1,1) 時, 選用 NI 設為 (1,1,1,1) 時, 通道 Disable - 7 -

9 CR# 參數位址 保持型暫存器名稱說明 #2 H 4066 O R/W CH1 平均次數 #3 H 4067 O R/W CH2 平均次數 #4 H 4068 O R/W CH3 平均次數 #5 H 4069 O R/W CH4 平均次數 #6 H 406A X R CH1 量測攝氏溫度平均值 #7 H 406B X R CH2 量測攝氏溫度平均值 #8 H 406C X R CH3 量測攝氏溫度平均值 #9 H 406D X R CH4 量測攝氏溫度平均值 #12 H 4070 X R CH1 量測華氏溫度平均值 #13 H 4071 X R CH2 量測華氏溫度平均值 #14 H 4072 X R CH3 量測華氏溫度平均值 #15 H 4073 X R CH4 量測華氏溫度平均值 #18 H 4076 X R CH1 量測攝氏溫度現在值 #19 H 4077 X R CH2 量測攝氏溫度現在值 #20 H 4078 X R CH3 量測攝氏溫度現在值 #21 H 4079 X R CH4 量測攝氏溫度現在值 #24 H 407C X R CH1 量測華氏溫度現在值 #25 H 407D X R CH2 量測華氏溫度現在值 #26 H 407E X R CH3 量測華氏溫度現在值 #27 H 407F X R CH4 量測華氏溫度現在值 #29 H 4081 X R/W PID 模式設定 #30 H 4082 X R 錯誤狀態 #31 H 4083 O R/W 通訊位址設定 #32 H 4084 O R/W 通訊速率 (Baud rate) 設定 #33 H 4085 O R/W 恢復出廠設定 通道 CH1 ~ CH4 訊號的平均次數設定 : V3.04 以前版本 : 可設定範圍 K1 ~ K4,095 V3.05 以後版本 : 可設定範圍 K1 ~ K20 出廠設定值為 K10 通道 CH1 ~ CH4 量測攝氏溫度平均值顯示 單位 0.1 C 通道 CH1 ~ CH2 量測華氏溫度平均值顯示 單位 0.1 F 通道 CH3~ CH4 量測華氏溫度平均值顯示 單位 0.1 F 通道 CH1 ~ CH4 量測攝氏溫度現在值顯示 單位 0.1 C 通道 CH1 ~ CH4 量測華氏溫度現在值顯示 單位 0.1 F 設定 H 5678 進入 PID 模式, 其他設定值皆為一般模式 出廠設定值 H 0000 儲存所有錯誤狀態的資料暫存器, 詳細內容請參照錯誤信息表 設定 RS-485 通訊位址, 設定範圍 01 ~ 254 出廠設定值為 K1 包含 ASCII/RTU 模式,ASCII 模式資料格式為 7 bits 偶位元 1 stop bit (7, E, 1); RTU 模式資料格式為 8 bits 偶位元 1 stop bit (8, E, 1) 通訊速率設定共有六種 : b0:4,800 bps b1:9,600 bps( 出廠設定值 ) b2:19,200 bps b3:38,400 bps b4:57,600 bps b5:115,200 bps b6 ~ b13: 保留 b14:crc 檢查碼高低位交換 ( 僅 RTU 模式有效 ) b15:ascii/rtu 模式切換 b15~b12 b11~ b9 b8~b6 b5~b3 b2~b0 ERR 燈 CH4 CH3 CH2 CH1 以 CH1 設定來說明 : 1. b0 ~ b1 保留 2. b2 設定為 1 時, 所有設定值將回復原廠設定值

10 CR# 參數位址 保持型暫存器名稱說明 #33 H 4085 O R/W 恢復出廠設定 #34 H 4086 O R 韌體版本 #35 ~ #48 系統內部使用 ERR 燈定義 : 原廠設定值 b12 ~ b15 = b12 對應 CH1, 當 b12=1 時, 刻度超過 ERR 燈閃爍動作 2. b13 對應 CH2, 當 b13=1 時, 刻度超過 ERR 燈閃爍動作 3. b14 對應 CH3, 當 b14=1 時, 刻度超過 ERR 燈閃爍動作 4. b15 對應 CH4, 當 b15=1 時, 刻度超過 ERR 燈閃爍動作 16 進制, 顯示目前韌體版本, 如 1.0A 則 H 010A 符號定義 : O 表示為保持型 ;X 表示為非保持型 ( 利用 RS-485 通訊控制時支援, 連接主機時不支援 ) R 表示為可使用 FROM 指令讀取資料, 或利用 RS-485 通訊讀取資料 W 表示為可使用 TO 指令寫入資料, 或利用 RS-485 通訊寫入資料 1. 功能碼 (Function):03 H 讀出暫存器資料 06 H 寫入一個 word 資料至暫存器 10 H 寫入多筆 words 資料至暫存器 2. CR#30 錯誤狀態表 : 錯誤狀態 內容值 b15 ~b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 電源異常 K1 (H 1) 接點空接 K2 (H 2) 硬體故障 K16 (H 10) 平均次數設定錯誤 K64 (H 40) 指令錯誤 K128 (H 80) CH1 接點空接 ( 轉換異常 ) CH2 接點空接 ( 轉換異常 ) CH3 接點空接 ( 轉換異常 ) CH4 接點空接 ( 轉換異常 ) K256(H 100) 保留 K512 (H 200) K1024(H 400) K2048(H 800) 註 : 每個錯誤狀態由相對應之位元 b0 ~ b7 決定, 有可能會同時產生兩個以上之錯誤狀態,0 代表正常無錯誤,1 代表有錯誤狀態產生 3. DVP04PT-S 在 V3.08 以上版本, 當 CR#29 設定為 H 5678 時,CR#0 ~ CR#34 可做為 PID 設定使用 : PID 模式內容說明 CR#0 機種型號 CR#22 CH4 K I CR#2 CH1 PID 輸出 % CR#24 CH1 K D CR#3 CH2 PID 輸出 % CR#25 CH2 K D CR#4 CH3 PID 輸出 % CR#26 CH3 K D CR#5 CH4 PID 輸出 % CR#27 CH4 K D - 9 -

11 CR#2~CR#5: 範圍 :0~1000, 單位 0.1% PID 模式內容說明 Run/Stop & Auto tuning CR#6 CH1 攝氏平均溫度 Bit0:CH1 PID Run/Stop CR#7 CH2 攝氏平均溫度 Bit1:CH2 PID Run/Stop CR#8 CH3 攝氏平均溫度 Bit2:CH3 PID Run/Stop CR#9 CH4 攝氏平均溫度 Bit3:CH4 PID Run/Stop CR#6~CR#9: 單位 0.1 C 0=PID Stop,1=PID Run CR#28 CR#10 CH1 溫度設定 Bit4:CH1 Auto tuning CR#11 CH2 溫度設定 Bit5:CH2 Auto tuning CR#12 CH3 溫度設定 Bit6:CH3 Auto tuning CR#13 CH4 溫度設定 Bit7:CH4 Auto tuning CR#10~CR#13:PID 目標值設定 (SV) CR#14 CH1 K P CR#29 CR#15 CH2 K P CR#30 錯誤碼 設為 1 會進入 Auto turning 功能, 完畢時自動改為 0 進入 PID 模式 (H 5678) 寫回 K0, 退出 PID 模式 CR#16 CH3 K P CR#31 CH1 取樣時間 CR#17 CH4 K P CR#32 CH2 取樣時間 CR#19 CH1 K I CR#33 CH3 取樣時間 CR#20 CH2 K I CR#34 CH4 取樣時間 CR#21 CH3 K I CR#31~CR#34: 範圍 1~30, 單位 1s 註 : 需先進入 PID 模式 (CR#29 寫入 H 5678), 再對其它 CR 做設定 溫度 數位特性曲線 攝 ( 華 ) 氏溫度量測模式 : 數位輸出 Max. Min. Min. Max. 量測溫度輸入 鉑金 輸入溫度範圍 數位轉換範圍 電阻 C (Min. / Max.) F (Min. / Max.) C (Min. / Max.) F (Min. / Max.) PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,380 PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,

12 简体中文 感谢您采用台达 DVP 系列产品 DVP04PT-S 温度测量模块可接受外部 4 点铂金属温度传感器, 将之转换成 16 位的数字信号 透过 DVP-PLC SS/ SA/SX/SC/SV 主机程序以指令 FROM/TO 来读写模块内的数据, 模块内具有多个 CR (Control Register) 寄存器, 每个寄存器有 16 bits 电源单元与模块分离, 体积小, 安装容易 请在使用之前, 详细阅读本使用说明书 实施配线, 务必关闭电源 上电时请勿接触机体端子或进行维修 输入电源切断后, 一分钟之内, 请勿触摸内部电路 本机为开放型 (OPEN TYPE) 机壳, 因此使用者使用本机时, 必须将其安装于具防尘 防潮及免于电击 冲击意外的外壳配线箱内 另必须具备保护措施 ( 如 : 特殊的工具或钥匙才可打开 ) 防止非维护人员操作或意外冲击本体, 造成危险及损坏 交流输入电源不可连接于输入 出信号端, 否则可能造成严重的损坏, 因此请在上电之前再次确认电源配线 本体上的接地端子务必正确的接地, 可提高产品抗干扰能力 由测温体到温调本体的配线路请用最短距离配线, 为了避免干扰及诱导的影响尽可能将电源线和负载配线分开 产品外观尺寸与部位介绍 详细部位指示图与外观尺寸请参阅英文版页码 1 的 [Figure1], 单位 :mm 1. 电源 错误及运行指示灯 6. I/O 模块定位孔 11. RS-485 通讯口 2. 机种型号 7. 铭牌 12. I/O 模块固定槽 3. DIN 轨固定扣 8. I/O 模块连接口 13. 电源输入口 4. 端子 9. I/O 模块固定扣 14. I/O 模块连接口 5. 端子配置 10. DIN 轨糟 (35mm) 输入 输出端子台配置 请参阅英文版页码 2 的端子台配置示意图 外部配线 3- wire PT100 隔離線 *1 CH1 I- 1.53mA PT1000 隔離線 *1 CH4 2-wire I- *2 接至電源模組之端 *3 24+ 系統接地點 24- 第三種接地 ( 接地抗阻 100 以下 ) DC/ DC 轉換器 mA 5V +15V -15V 注 1: 使用于模拟输入的配线应采用温度传感器的连接线或双绞隔离线且应与其它电源线或可能引起干扰之接线分开 注 2: 如果干扰过大请将 及接地端子连接 注 3: 请将电源模块的端及 DVP04PT-S 温度测量模块的端连接到系统接地点, 再将系统接点作第三种接地或接到配电箱的机壳上 注意 : 空端子请勿配线

13 电气规格 电源电压 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) 额定最大消耗功率 操作 储存环境 耐振动 冲击 与 DVP-PLC 主机串接说明 功能规格 2W, 由外部电源供应 1. 操作 :0 C ~ 55 C( 温度 ),5 ~ 95%( 湿度 ), 污染等级 2 2. 储存 :-25 C ~ 70 C( 温度 ),5 ~ 95%( 湿度 ) 国际标准规范 IEC , IEC (TEST Fc)/IEC & IEC (TEST Ea) 模块编号以靠近主机的顺序自动编号由 0 到 7, 最大可连接 8 台且不占用数字 I/O 点数 DVP04PT-S 摄氏 ( C) 华氏 ( F) 模拟讯号输入通道 适合感应器形式 驱动电流 输入温度范围 数字转换范围 4 通道 台 2 线 /3 线 PT100/ Ni100/ PT1000/ Ni PPM/ C (DIN JIS C ) 1.53mA / 204.8uA 请參阅温度 數位特性曲线附表 请參阅温度 數位特性曲线附表 分辨率 16 bits (0.1 C) 16 bits (0.1 F) 总和精密度 响应时间 隔离方式 数字数据格式 平均功能 自我诊断功能 0.6% 在 (0 ~ 55 C, 32 ~ 131 F) 范围内满刻度时 200ms 通道数 数字电路与模拟电路有隔离, 通道间未隔离 数字电路与接地之间 :500VDC 模拟电路与接地之间 :500VDC 模拟电路与数字电路之间 :500VDC 24VDC 与接地之间 :500VDC 16 位二补码 有 (CR#2 ~ CR#5) 上下极限侦测 / 通道 通讯模式 (RS-485) 有 (CR#32) 当与 PLC 主机串接时,RS-485 通讯无法使用 控制寄存器 (CR) CR# 参数地址 保持型寄存器名称说明 #0 H 4064 O R 机种型号系统内定,DVP04PT-S 机种编码 = H 8A #1 H 4065 O R/W 模式设定 CH1 模式 :b0 ~ b3 CH2 模式 :b4 ~ b7 CH3 模式 :b8 ~ b11 CH4 模式 :b12 ~ b15 以 CH1 设定 (b3,b2,b1,b0) 说明, 默认值 H 0000: 1. 设为 (0,0,0,0) 时, 选用 PT 设为 (0,0,0,1) 时, 选用 NI 设为 (0,0,1,0) 时, 选用 PT 设为 (0,0,1,1) 时, 选用 NI 设为 (1,1,1,1) 时, 通道 Disable

14 CR# 参数地址 保持型寄存器名称说明 #2 H 4066 O R/W CH1 平均次数 #3 H 4067 O R/W CH2 平均次数 #4 H 4068 O R/W CH3 平均次数 #5 H 4069 O R/W CH4 平均次数 #6 H 406A X R CH1 测量摄氏温度平均值 #7 H 406B X R CH2 测量摄氏温度平均值 #8 H 406C X R CH3 测量摄氏温度平均值 #9 H 406D X R CH4 测量摄氏温度平均值 #12 H 4070 X R CH1 测量华氏温度平均值 #13 H 4071 X R CH2 测量华氏温度平均值 #14 H 4072 X R CH3 测量华氏温度平均值 #15 H 4073 X R CH4 测量华氏温度平均值 #18 H 4076 X R CH1 测量摄氏温度现在值 #19 H 4077 X R CH2 测量摄氏温度现在值 #20 H 4078 X R CH3 测量摄氏温度现在值 #21 H 4079 X R CH4 测量摄氏温度现在值 #24 H 407C X R CH1 测量华氏温度现在值 #25 H 407D X R CH2 测量华氏温度现在值 #26 H 407E X R CH3 测量华氏温度现在值 #27 H 407F X R CH4 测量华氏温度现在值 #29 H 4081 X R/W PID 模式设定 #30 H 4082 X R 错误状态 #31 H 4083 O R/W 通讯地址设定 #32 H 4084 O R/W 通讯速率 (Baud rate) 设定 #33 H 4085 O R/W 恢复出厂设定 通道 CH1 ~ CH4 信号的平均次数设定 : V3.04 以前版本 : 可设定范围 K1 ~ K4,095 V3.05 以后版本 : 可设定范围 K1 ~ K20 出厂默认值为 K10 通道 CH1 ~ CH4 测量摄氏温度平均值显示 单位 0.1 C 通道 CH1 ~ CH2 测量华氏温度平均值显示 单位 0.1 F 通道 CH3 ~ CH4 测量华氏温度平均值显示 单位 0.1 F 通道 CH1 ~ CH4 测量摄氏温度现在值显示 单位 0.1 C 通道 CH1 ~ CH4 测量华氏温度现在值显示 单位 0.1 F 设定 H 5678 进入 PID 模式, 其它设定值皆为一般模式 出厂默认值 H 0000 储存所有错误状态的数据寄存器, 详细内容请参照错误信息表 设定 RS-485 通讯地址, 设定范围 01 ~ 254 出厂默认值为 K1 包含 ASCII/RTU 模式,ASCII 模式数据格式固定为 7 bits 偶位 1 stop bit (7, E, 1), RTU 模式数据格式固定为 8 bits 偶位 1 stop bit (8, E, 1) 通讯速率设定共有六种 : b0:4,800 bps b1:9,600 bps( 出厂设定值 ) b2:19,200 bps b3:38,400 bps b4:57,600 bps b5:115,200 bps b6 ~ b13: 保留 b14:crc 检查码高低位交换 ( 仅 RTU 模式有效 ) b15:ascii/rtu 模式切换 b15~b12 b11~ b9 b8~b6 b5~b3 b2~b0 ERR 灯 CH4 CH3 CH2 CH1 以 CH1 设定来说明 : 1. b0 ~ b1 保留 2. b2 设定为 1 时, 所有设定值将回复原厂默认值

15 CR# 参数地址 保持型寄存器名称说明 #33 H 4085 O R/W 恢复出厂设定 #34 H 4086 O R 韧体版本 #35 ~ #48 系统内部使用 ERR 灯定义 : 原厂设定值 b12 ~ b15 = b12 对应 CH1, 当 b12=1 时, 刻度超过 ERR 灯闪烁动作 2. b13 对应 CH2, 当 b13=1 时, 刻度超过 ERR 灯闪烁动作 3. b14 对应 CH3, 当 b14=1 时, 刻度超过 ERR 灯闪烁动作 4. b15 对应 CH4, 当 b15=1 时, 刻度超过 ERR 灯闪烁动作 16 进制, 显示目前韧体版本, 如 1.0A 则 H 010A 符号定义 : O 表示为保持型 ;X 表示为非保持型 ( 利用 RS-485 通讯控制时支持, 连接主机时不支持 ) R 表示为可使用 FROM 指令读取数据, 或利用 RS-485 通讯读取数据 W 表示为可使用 TO 指令写入数据, 或利用 RS-485 通讯写入数据 1. 功能码 (Function):03 H 读出寄存器数据 06 H 写入一个 word 数据至寄存器 10 H 写入多笔 words 数据至寄存器 2. CR#30 错误状态表 : 错误状态 内容值 b15 ~b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 电源异常 K1 (H 1) 接点空接 K2 (H 2) 硬件故障 K16 (H 10) 平均次数设定错误 K64 (H 40) 指令错误 K128 (H 80) CH1 接点空接 ( 转换异常 ) CH2 接点空接 ( 转换异常 ) CH3 接点空接 ( 转换异常 ) CH4 接点空接 ( 转换异常 ) K256(H 100) 保留 K512 (H 200) K1024(H 400) K2048(H 800) 注 : 每个错误状态由相对应之位 b0 ~ b7 决定, 有可能会同时产生两个以上之错误状态,0 代表正常无错误,1 代表有错误状态产生 3. DVP04PT-S 在 V3.08 以上版本, 当 CR#29 设定为 H 5678 时,CR#0 ~ CR#34 可做为 PID 设定使用 : PID 模式内容说明 CR#0 机种型号 CR#22 CH4 K I CR#2 CH1 PID 输出 % CR#24 CH1 K D CR#3 CH2 PID 输出 % CR#25 CH2 K D CR#4 CH3 PID 输出 % CR#26 CH3 K D CR#5 CH4 PID 输出 % CR#27 CH4 K D

16 CR#2~CR#5: 范围 :0~1000, 单位 0.1% PID 模式内容说明 Run/Stop & Auto tuning CR#6 CH1 摄氏平均温度 Bit0:CH1 PID Run/Stop CR#7 CH2 摄氏平均温度 Bit1:CH2 PID Run/Stop CR#8 CH3 摄氏平均温度 Bit2:CH3 PID Run/Stop CR#9 CH4 摄氏平均温度 Bit3:CH4 PID Run/Stop CR#6~CR#9: 单位 0.1 C 0=PID Stop,1=PID Run CR#28 CR#10 CH1 温度设定 Bit4:CH1 Auto tuning CR#11 CH2 温度设定 Bit5:CH2 Auto tuning CR#12 CH3 温度设定 Bit6:CH3 Auto tuning CR#13 CH4 温度设定 Bit7:CH4 Auto tuning CR#10~CR#13:PID 目标值设定 (SV) CR#14 CH1 K P CR#29 CR#15 CH2 K P CR#30 错误码 设为 1 会进入 Auto turning 功能, 完毕时自动改为 0 进入 PID 模式 (H 5678) 写回 K0, 退出 PID 模式 CR#16 CH3 K P CR#31 CH1 取样时间 CR#17 CH4 K P CR#32 CH2 取样时间 CR#19 CH1 K I CR#33 CH3 取样时间 CR#20 CH2 K I CR#34 CH4 取样时间 CR#21 CH3 K I CR#31~CR#34: 范围 1~30, 单位 1s 注 : 需先进入 PID 模式 (CR#29 写入 H 5678), 再对其它 CR 做设定 温度 数字特性曲线 摄 ( 华 ) 氏温度量测模式 : 數位輸出 Max. Min. Min. Max. 量測溫度輸入 铂金 输入温度范围 数字转换范围 电阻 C (Min. / Max.) F (Min. / Max.) C (Min. / Max.) F (Min. / Max.) PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,380 PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,

17 TÜRKÇE Delta DVP serisi PLC leri seçtiğiniz için teşekkürler. DVP04PT-S ünitelerine 4 adet platinyum sıcaklık sensörü bağlanabilir ve bu bağlı sıcaklık sensörlerinden gelen bilgiler 16-bit dijital sinyallere dönüştürülür. Ayrıca DVP PLC CPU da FROM/TO komutları kullanılarak DVP04PT-S modülünün içine veri yazılabilir veya okunabilir. DVP04PT-S modülünün içinde çok adet 16-bit kontrol register (CR) vardır. Ürünün beslemesi ayrı olup küçük boyutlu ve kurulumu kolaydır. Lütfen ürünü kullanmadan önce bu bilgi dökümanını dikkatlice okuyunuz. Üründe enerji varken terminallere dokunmayınız. Bu ürün AÇIK TİP I/O modülü olduğundan dolayı toz, rutubet, elektrik şoku ve titreşimden uzak kapalı yerlere kurulumu yapılmalıdır. Tehlikeleri ve ürünün zarar görmesini engellemek için yetkili olmayan kişilerin ürüne müdahale etmesini engelleyecek önlemler alınmalıdır. (Ör: Panoya kilit konulması gibi). DVP04PT-S ünitesinin giriş/çıkış terminallerine AC power bağlamayınız, Aksi halde ürün zarar görebilir. Elektromanyetik gürültüyü engellemek için, DVP04PT-S ürününün topraklamasının doğru olduğuna emin olunuz. Ürüne bağlanacak sensör (RTD) kablolarını mümkün olduğunca kısa bağlayınız ve elektriksel gürültüyü önlemek için I/O kablolarını güç kablolarından uzak tutunuz. Ürün Görünüşü & Ölçüler Lütfen sayfa 1 de (Şekil 1) ye bakınız., Birim: mm. 1. Durum indikatör (POWER, RUN ve ERROR) 8. I/O modul bağlantı portu 2. Model adı 9. I/O modul klip 3. DIN ray klip 10. DIN ray (35mm) 4. I/O terminaller 11. RS-485 haberleşme portu 5. I/O nokta indikatör 12. I/O modul klip 6. Montaj delikleri 13. DC power girişi 7. Ürün Özellik Etiketi 14. I/O modul bağlantı portu I/O Terminal Yerleşimi Lütfen İngilizce versiyonu için sayfa 1 ye bakınız. Harici Bağlantı 3- wi re PT100 Shielded cable*1 CH 1 I mA PT1000 Shielded cable*1 CH mA 2- wi re I- 5V *2 Terminal of the power module +15V * DC / DC System 24 - Grounding -15V Class 3 Grounding (Below 100 ) Not 1: Ürüne giriş bağlantısı yaparken sıcaklık sensörünün orjinal kablosunu kullanınız ve bu kabloları gürültüden etkilenmemesi için güç kablolarından uzuk tutunuz. Not 2: Gürültüyü önlemek için terminalini topraklayınız. Not 3: Güç kaynağı modülü terminalinden ve DVP04PT-S modülü toprak terminalinden topraklanmalıdır. Uyarı: No Connection (NC) terminallerine bağlantı yapmayınız. Elektriksel Özellikler Power supply voltajı 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) Max. güç tüketim oranı 2W, harici beslemeden beslenir. Çalışma/saklama Çalışma: 0 C~55 C (sıcaklık), 5~95% (rutubet), kirlenme derecesi 2 Saklama: -25 C~70 C (sıcaklık), 5~95% (rutubet) Titreşim/şok direnci Uluslararası standartlar: IEC , IEC (TEST Fc)/ IEC & IEC (TEST Ea)

18 DVP-PLC MPU ya seri bağlantı Fonksiyonel Özellikler Modül CPU ya bağlandığında uzaklığına göre sırasıyla otomatik olarak 0 7 arası numaralandırılır. En yakın modülün numarası 0 ve en uzaktaki modülün numarası 7 dir. Maksimum 8 adet özel modül bağlanabilir ve digital I/O işgal etmezler. DVP04PT-S Celsius ( C) Fahrenheit ( F) Analog giriş kanalı Herbir modül için 4 kanal Sensors tipi 2-telli/3-telli PT100/ Ni100/ PT1000/ Ni PPM/ C (DIN JIS C ) Akım eksitasyon 1.53mA / 204.8uA Sıcaklık giriş aralığı Lütfen sıcaklık/dijital değer karakteristik eğrisini inceleyiniz. Digital dönüşüm aralığı Lütfen sıcaklık/dijital değer karakteristik eğrisini inceleyiniz. Çözünürlük 16 bit (0.1 C) 16 bit (0.1 F) Genel doğruluk 0.6% tam skala 0 ~ 55 C (32 ~ 131 F) de Cevap zamanı 200ms kanal Digital ve analog devreler arasında izolasyon mevcut. Kanallar arası izolasyon yok. Izolasyon metodu 500VDC Dijital devreler ve Toprak (Ground) arasında 500VDC Analog devreler ve Toprak (Ground) arasında 500VDC Analog devreler ve Dijital devreler arasında 500VDC 24VDC ve Toprak (Ground) arasında Digital data formatı 16-bit, 2 nin komplementi Ortalama fonksiyonu Mevcut (CR#2 ~ CR#5) Self diagnostic fonksiyonu Mevcut Haberleşme modu (RS-485) Mevcut (CR#32). DVP04PT-S ünitesi CPU nun yanına takıldığı zaman RS-485 pasif olur. Kontrol Register CR# Adres Kayıt Register içeriği Açıklama #0 H 4064 O R Model adı #1 H 4065 O R/W Mod ayarı #1 H 4065 O R/W Mod ayarı #2 H 4066 O R/W CH1 ortalama adeti #3 H 4067 O R/W CH2 ortalama adeti #4 H 4068 O R/W CH3 ortalama adeti #5 H 4069 O R/W CH4 ortalama adeti #6 H 406A X R CH1 ortalama sıcaklık #7 H 406B X R CH2 ortalama sıcaklık #8 H 406C X R CH3 ortalama sıcaklık #9 H 406D X R CH4 ortalama sıcaklık #12 H 4070 X R CH1 ortalama sıcaklık #13 H 4071 X R CH2 ortalama sıcaklık #14 H 4072 X R CH3 ortalama sıcaklık #15 H 4073 X R CH4 ortalama sıcaklık #18 H 4076 X R CH1 mevcut sıcaklık #19 H 4077 X R CH2 mevcut sıcaklık #20 H 4078 X R CH3 mevcut sıcaklık #21 H 4079 X R CH4 mevcut sıcaklık #24 H 407C X R CH1 mevcut sıcaklık #25 H 407D X R CH2 mevcut sıcaklık #26 H 407E X R CH3 mevcut sıcaklık #27 H 407F X R CH4 mevcut sıcaklık Sistem tarafından ayarlanır: DVP04PT model kodu = H 8A. CH1 mod: b0 ~ b3 CH2 mod: b4 ~ b7 CH3 mod: b8 ~ b11 CH4 mod: b12 ~ b15 CH1 mod (b3,b2,b1,b0) örneğini alalım. Default değeri H (0,0,0,0): PT (0,0,0,1): NI (0,0,1,0): PT (0,0,1,1): NI (1,1,1,1): kanal pasif. CH1 ~ CH4 kanallarındaki ortalama sıcaklık değerini hesaplamak için okuma sayısıdır. Ayar aralığı: V3.04 ve öncesi: K1 ~ K4,095. V3.05 ve sonrası: K1 ~ K20. Default ayarı K10. CH1 ~ CH4 ortalama sıcaklık değeri. (Birim: 0.1 C). CH1 ~ CH4 ortalama sıcaklık değeri. (Birim: 0.1 F). CH1 ~ CH2 mevcut sıcaklık değeri. (Birim: 0.1 C). CH3 ~ CH4 mevcut sıcaklık değeri. (Birim: 0.1 C). CH1 ~ CH4 mevcut sıcaklık değeri. (Birim: 0.1 F).

19 CR# Adres Kayıt Register içeriği Açıklama #29 H 4081 X R/W PID mod ayarı #30 H 4082 X R Error (Hata) durumu #31 H 4083 O R/W #32 H 4084 O R/W #32 H 4084 O R/W #33 H 4085 O R/W #33 H 4085 O R/W Haberleşme adresi ayarı Haberleşme hızı (baud rate) ayarı Haberleşme hızı (baud rate) ayarı Fabrika Ayarlarına Reset Fabrika Ayarlarına Reset #34 H 4086 O R Software versiyon PID modu aktif etmek için H'5678 ayarlayın. Diğer ayarlar geçersizdir. Default: H Hata kodu data register içine kaydedilir. Lütfen hata kodu tablosuna bakınız. RS-485 haberleşme adresi. Ayar aralığı : 01 ~ 254 ve default : K1. Haberleşme baud rate (4,800, 9,600, 19,200, 38,400, 57,600 ve 115,200bps). ASCII mod için, data formatı 7 bit, even, 1 stop bit (7, E, 1), RTU modda iken, data formatı 8 bit, even, 1 stop bit (8, E, 1). b0: 4,800 bps (bit/sn). b1: 9,600 bps (bit/sn). (default ayarı) b2: 19,200 bps (bit/sn). b3: 38,400 bps (bit/sn). b4: bps (bit/sn). b5: 115,200 bps (bit/sn). b6 ~ b13: Reserve. b14: CRC code düşük bit ve yüksek bit arasında anahtarlama (Sadece RTU modda). b15: RTU mod. b15~b12 b11~ b9 b8~b6 b5~b3 b2~b0 ERR LED CH4 CH3 CH2 CH1 Örnek: CH1 ayarı 1. b0 ~ b1: Reserve. 2. b2: 1 yapılır ve ürün fabrika ayarlarına resetlenir. ERR LED açıklaması: b12~b15=1111 (default ayarlar) 1. b12 CH1 kanalı : b12=1 ise okunan değer sınırı aştı, ERR LED flash yapar. 2. b13 CH2 kanalı : b13=1 ise okunan değer sınırı aştı, ERR LED flash yapar. 3. b14 CH3 kanalı : b14=1 ise okunan değer sınırı aştı, ERR LED flash yapar. 4. b15 CH4 kanalı : b15=1 ise okunan değer sınırı aştı, ERR LED flash yapar. Yazılım versiyonunu heksadesimal olarak gösterir. Ör: H 010A = versiyon 1.0A #35 ~ #48 Sistem kullanır Semboller: O: kalıcı. X: kalıcı değil. (RS-485 haberleşme kullanılırken destekler, CPU nun yanına takıldığı zaman desteklemez) R: FROM komutu veya RS-485 kullanılarak okunabilen data. W: FROM komutu veya RS-485 kullanılarak yazılabilen data. 1. Fonksiyon kodu: 03 H registerden data okuma. 06 H registere 1 word yazma. 10 H registerlere çoklu word yazma. 2. CR#30 hata kodu (error code) register. Aşağıdaki tabloyu inceleyiniz: Hata açıklaması İçerik b15- b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 b12 Power beslemesi anormal K1 (H 1) Kontak hiçbir yere bağlı değil K2 (H 2) Donanım hatası K16 (H 10) Ortalama adet ayarı hatası K64 (H 40) Komut hatası K128 (H 80) CH1 kontağı hiçbir yere bağlı değil. (Anormal dönüşüm) CH2 kontağı hiçbir yere bağlı değil. (Anormal dönüşüm) CH3 kontağı hiçbir yere bağlı değil. (Anormal dönüşüm) CH4 kontağı hiçbir yere bağlı değil. (Anormal dönüşüm) K256 (H 100) K512 (H 200) K1024 (H 400) K2048 (H 800) Rezerve

20 Hata açıklaması İçerik b15- b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 b12 Not: Her hata kodu bir bite karşılık gelecektir (b0 ~ b7). İki veya daha fazla hata aynı anda meydana gelebilir. 0 normal durumu 1 ise hata olduğunu gösterir. 3. CR#29 değeri H 5678 ayarlandığı zaman, DVP04PT-S V3.08 ve üzeri versiyonlarda CR#0 ~ CR#34 kontrol registerleri PID ayarları için kullanılabilir. PID Modu İçerik Açıklaması CR#0 Model adı CR#22 CH4 KI CR#2 PID çıkış % CH1 CR#24 CH1 KD CR#3 PID çıkış % CH2 CR#25 CH2 KD CR#4 PID çıkış % CH3 CR#26 CH3 KD CR#5 PID çıkış % CH4 CR#27 CH4 KD CR#2~CR#5: 0~1000; Birim: 0.1% Run/Stop & Auto tuning CR#6 CH1 ortalama sıcaklık ( C) Bit0: CH1 PID run/stop CR#7 CH2 ortalama sıcaklık ( C) Bit1: CH2 PID run/stop CR#8 CH3 ortalama sıcaklık ( C) Bit2: CH3 PID run/stop CR#9 CH4 ortalama sıcaklık ( C) Bit3: CH4 PID run/stop CR#6~CR#9: Birim: 0.1 C 0=PID stop; 1=PID run CR#10 CH1 sıcaklık ayarı CR#28 Bit4: CH1 auto tuning CR#11 CH2 sıcaklık ayarı Bit5: CH2 auto tuning CR#12 CH3 sıcaklık ayarı Bit6: CH3 auto tuning CR#13 CH4 sıcaklık ayarı Bit7: CH4 auto tuning 1: Auto tuning fonksiyonu etkindir. Auto CR#10~CR#13: PID hedef set değeri (SV) tuning işlemi tamamlandıktan sonra, değer 0 olur. CR#14 CH1 KP PID moduna giriş (H 5678) CR#29 K0: PID modundan çıkış CR#15 CH2 KP CR#30 Hata (Error) Kodu CR#16 CH3 KP CR#31 CH1 Örnekleme zamanı CR#17 CH4 KP CR#32 CH2 Örnekleme zamanı CR#19 CH1 KI CR#33 CH3 Örnekleme zamanı CR#20 CH2 KI CR#34 CH4 Örnekleme zamanı CR#21 CH3 KI CR#31~CR#34: 1~30; Birim: 1s Not: Diğer kontrol registerlarını ayarlamadan önce PID modunu (CR # 29 = H'5678) aktif etmeniz gerekmektedir. Sıcaklık/Dijital Değer Karakteristik Eğrisi Santigrat (Fahrenhayt) sıcaklık ölçme modu: Digital output Max. Min. Min. Max. Temperature input Platinyum Sıcaklık aralığı Dijital değer dönüşüm aralığı resistor C (Min./Max.) F (Min./Max.) C (Min./Max.) F (Min./Max.) PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,380 PT ~ 800 C -292 ~ 1,472 F K-1,800 ~ K8,000 K-2,920 ~ K14,720 NI ~ 170 C -112 ~ 338 F K-800 ~ K1,700 K-1,120 ~ K3,

Microsoft Word T407

Microsoft Word T407 2015-02-03 5011669907-T407 . ENGLISH Thank you for choosing Delta DVP series PLC. DVP04TC-S is able to receive 4 points of external thermocouple temperature sensors and convert them into 14-point digital

More information

Microsoft Word PT04_TSE.doc

Microsoft Word PT04_TSE.doc ENGLISH DVP04PT-H2 is able to receive 4 points of resistance temperature detectors (PT100, PT1000, NI100, and NI1000) and convert them into 16-bit digital signals. Besides, through the user of FROM/TO

More information

Microsoft Word P03.doc

Microsoft Word P03.doc C L- H 1 I - C L- H 2 I - C L- H 3 I - C L- H 4 I - C L- H 5 I - C L- H 6 I - ENGLISH Thank you for choosing Delta DVP series PLC. DVP04/06PT-S is able to receive 4/6 points of RTDs and convert them into

More information

Microsoft Word PT09_TSE.doc

Microsoft Word PT09_TSE.doc 2017-06-08 5011675807-PT09 ENGLISH DVP04PT-H2 is able to receive 4 points of resistance temperature detectors (PT100, PT1000, NI100, and NI1000) and convert them into 16-bit digital signals. Besides, through

More information

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family small, speedy, safe Eextremely modular Up to 64 modules per bus de Quick reaction time: up to 20 µs A new Member of the Cube Family Murrelektronik s modular I/O system expands the field-tested Cube family

More information

Microsoft Word E2P2.doc

Microsoft Word E2P2.doc 4AI-PT ENGLISH Thank you for choosing Delta s DVP series PLC. DVP4PT-E2 temperature measurement module receives 4 points of platinum temperature sensors (PT1 3-WIRE 1Ω 385 PPM/ C (DIN 4376 JIS C164-1989)/

More information

Microsoft Word E2T2.doc

Microsoft Word E2T2.doc 4AI-TC ENGLISH Thank you for choosing Delta s DVP series PLC. DVP4TC-E2 temperature measurement module receives 4 points of external thermocouple temperature sensors (J-type, K-type, R-type, S-type, T-type,

More information

Microsoft Word E2G2.doc

Microsoft Word E2G2.doc 2AO ENGLISH Thank you for choosing Delta s DVP series PLC. DVP02DA-E2 (DVP04DA-E2) analog output module receives 2 (4) groups of 16-bit digital data from the PLC MPU and converts the digital data into

More information

Microsoft Word A4L4_TSE.doc

Microsoft Word A4L4_TSE.doc 214-4-3 5116963-A4L4 ENGLISH Thank you for choosing Delta s DVP series PLC. The analog input module of DVP4AD-SL series can read/write the data of analog input module by using instructions FROM/TO via

More information

Microsoft Word - P SDV series.DOC

Microsoft Word - P SDV series.DOC 片式压敏电阻器 SDV 系列 Chip SDV Series Operating Temp. : -55 ~ +125 特征 SMD 结构适合高密度安装 优异的限压比, 响应时间短 (

More information

Microsoft Word D4L5_TSE.doc

Microsoft Word D4L5_TSE.doc 2014-04-30 5011695904-D4L5 ENGLISH Thank you for choosing DELTA DVP PLC Series. The analog output module of DVP04DA-SL series can read/write the data of analog output module by using instructions FROM/TO

More information

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact

More information

Rotary Switch Catalogue

Rotary Switch Catalogue Rotary Switches RS300/400/500 Series Outline Our RS series embody the manufacturing history of our company. All series are sturdy and solid with high dependability designed for control units of plants,

More information

User’s Manual

User’s Manual SNAP 500 打 印 机 用 户 手 册 1 用 户 手 册 SNAP TM 500 打 印 机 2015 年 8 月 24 日 AVERY DENNISON Manual Edition 2.5 2 SNAP 500 打 印 机 用 户 手 册 WARNING This device complies with Part 15 of the FCC Rules. Operation is subject

More information

HCD0174_2008

HCD0174_2008 Reliability Laboratory Page: 1 of 5 Date: December 23, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Chroma 61500/ bit / RMS RMS VA ()61500 DSP THD /61508/61507/61609/61608/ (61500 ) Chroma STEP PULSE : LISTLIST 100 AC DC

Chroma 61500/ bit / RMS RMS VA ()61500 DSP THD /61508/61507/61609/61608/ (61500 ) Chroma STEP PULSE : LISTLIST 100 AC DC MODEL 61509/61508/61507/ 61609/61608/61607 PROGRAMMABLE AC POWER SOURCE MODEL 61509/61508/61507/ 61609/61608/61607 61509/61609: 6kVA 61508/61608: 4.5kVA 61507/61607: 3kVA : 0-175V/0-350V/Auto : DC, 15Hz-2kHz

More information

MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / & 150KW / ( 10 ms ~ 99 hours)

MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / & 150KW / ( 10 ms ~ 99 hours) MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / &150KW / ( 10 ms ~ 99 hours) 10 100 / PROGRAMMABLE DC POWER SUPPLY MODEL 62000H SERIES USB

More information

Microsoft Word - LR1122B-B.doc

Microsoft Word - LR1122B-B.doc UNISONIC TECHNOLOGIES CO., LTD LOW NOISE ma LDO REGULATOR DESCRIPTION The UTC is a typical LDO (linear regulator) with the features of High output voltage accuracy, low supply current, low ON-resistance,

More information

BC04 Module_antenna__ doc

BC04 Module_antenna__ doc http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 1 of 10 http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 2 of 10 http://www.infobluetooth.com TEL:+86-23-68798999

More information

Microsoft Word - PZ series.doc

Microsoft Word - PZ series.doc 叠 层 片 式 铁 氧 体 磁 珠 P 系 列 Multilayer Chip Ferrite Bead P Series Operating Temp. : -4 ~ +8 特 征 FEATUES 内 部 印 有 银 电 极 的 叠 层 结 构, 铁 氧 体 屏 蔽 无 串 扰 Internal silver printed layers and magnetic shielded structures

More information

untitled

untitled 0000137925 REV 1.0 ... 4... 5... 6... 7... 8... 9... 11... 12... 13... 14... 15... 17... 18... 20... 22 ( 1)... 25... 26 ( 2)... 28 \ 1 ( 2A)... 29 \ 2 ( 2B)... 30 SSR ( 2C)... 31 \ ( 2D)... 32 \ ( 3A)...

More information

1-S40A...-1 DAT00452 V.005

1-S40A...-1 DAT00452 V.005 1. 1-S40A -1 Technical data: DATA SHEET Technical data Unit 1-S40A -1 OIML R60 D1 C3 Emax Max. capacity Kg 50,100,200,500 50,100,200,500 t 1, 2, 3, 5 1, 2, 3, 5 vmin % of Cn 0.0286 0.0120 Sensitivity mv/v

More information

Current Sensing Chip Resistor

Current Sensing Chip Resistor 承認書 APPROVAL SHEET 廠商 : 客戶 : 麗智電子 ( 昆山 ) 有限公司 核準審核制作核準審核簽收 公 司 章 公 司 章 Liz Electronics (Kunshan) Co., LTD No. 989, Hanpu Road Kunshan City Jiangsu Province China Tel:0086-0512-57780531 Fax:0086-0512-57789581

More information

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

HC50246_2009

HC50246_2009 Page: 1 of 7 Date: June 2, 2009 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

ICD ICD ICD ICD ICD

ICD ICD ICD ICD ICD MPLAB ICD2 MPLAB ICD2 PIC MPLAB-IDE V6.0 ICD2 usb PC RS232 MPLAB IDE PC PC 2.0 5.5V LED EEDATA MPLAB ICD2 Microchip MPLAB-IDE v6.0 Windows 95/98 Windows NT Windows 2000 www.elc-mcu.com 1 ICD2...4 1.1 ICD2...4

More information

Microsoft Word - SWRH-B series of Shielded SMD Power Inductor.doc

Microsoft Word - SWRH-B series of Shielded SMD Power Inductor.doc Wire Wound SMD Power Inductors SWRH-B Series Operating Temperature: -25 ~+105 (Including self-heating) FEATURES Various high power inductors are superior to be high saturation Suitable for surface mounting

More information

Microsoft Word E2X3.doc

Microsoft Word E2X3.doc ENGLISH Thank you for choosing Delta s DVP series PLC. DVP06XA-E2 mixed analog input/output module receives external 4 points of analog input signals (voltage or current) and converts them into 16-bit

More information

TX-NR3030_BAS_Cs_ indd

TX-NR3030_BAS_Cs_ indd TX-NR3030 http://www.onkyo.com/manual/txnr3030/adv/cs.html Cs 1 2 3 Speaker Cable 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT 1 DIGITAL OPTICAL OUT AUDIO OUT TV 3 1 5 4 6 1 2 3 3 2 2 4 3 2 5

More information

Table of Contents Power Film Capacitors Power Film Capacitors Series Table Product Type Series Voltage Capacitance() Page DC-Link Power Film Capacitors Power Film Capacitors Power Film Capacitors Power

More information

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn Xi III Zebra XI III 1 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn 230V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666

More information

01CP-WX3030WNetc_CO_ENG.indd

01CP-WX3030WNetc_CO_ENG.indd Data Video Projector User s Manual (Concise) ModelS: 8928A/8930A/8931WA/ 8933W Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please

More information

HC20131_2010

HC20131_2010 Page: 1 of 8 Date: April 14, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

untitled

untitled EDM12864-GR 1 24 1. ----------------------------------------------------3 2. ----------------------------------------------------3 3. ----------------------------------------------------3 4. -------------------------------------------------------6

More information

. Land Patterns for Reflow Soldering.Recommended Reflow Soldering Conditions (For Lead Free) TYPE PID0703 PID0704 PID1204 PID1205 PID1207 PID1209 L(mm

. Land Patterns for Reflow Soldering.Recommended Reflow Soldering Conditions (For Lead Free) TYPE PID0703 PID0704 PID1204 PID1205 PID1207 PID1209 L(mm .Features: 1.Magnetic Shielded surface mount inductor with high current rating. 2.Low resistance to keep power loss minimum..applications: Excellent for power line DC-DC conversion applications used in

More information

001Contents

001Contents Selection Guide Inductions of types Selection guide Contents 002 003 Standard capacitive sensors DC series AC series 008 024 Special capacitive sensors High temperature series Ring series 029 035 Accessories

More information

Microsoft Word E2X2.doc

Microsoft Word E2X2.doc ENGLISH Thank you for choosing Delta s DVP series PLC. DVP06XA-E2 mixed analog input/output module receives external 4 points of analog input signals (voltage or current) and converts them into 16-bit

More information

OA-253_H1~H4_OL.ai

OA-253_H1~H4_OL.ai WARNINGS Note: Read ALL the following BEFORE using this product. Follow all Guidelines at all times while using this product. CAUTION This warning indicates possibility of personal injury and material

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

untitled

untitled (100V 120V 220V 230V) i ii ! (Return Lead) iii iv 1....... 1 1-1.... 1 1-2.... 2 2..... 4 3..... 3-1.... 3-2.... 3-3....... 4..... 9 5......... 5-1.LCD..... 5-2.... 5-3.... 5-4.... 6..... 6-1.... 6-2....

More information

安 全 指 南 : 必 须 遵 守 所 有 的 警 告 事 项, 以 确 保 自 己 和 他 人 的 安 全 以 及 保 护 产 品 和 连 接 装 置 这 些 警 告 事 项 都 按 警 示 程 度 明 示 出 等 级 有 资 格 的 人 员 : YO-YO 只 能 进 行 与 手 册 有 关 的

安 全 指 南 : 必 须 遵 守 所 有 的 警 告 事 项, 以 确 保 自 己 和 他 人 的 安 全 以 及 保 护 产 品 和 连 接 装 置 这 些 警 告 事 项 都 按 警 示 程 度 明 示 出 等 级 有 资 格 的 人 员 : YO-YO 只 能 进 行 与 手 册 有 关 的 IOM LBYM180112 Rev. D Mark-4 /GP-4 Yo-Yo 重 锤 安 装 & 操 作 手 册 安 全 指 南 : 必 须 遵 守 所 有 的 警 告 事 项, 以 确 保 自 己 和 他 人 的 安 全 以 及 保 护 产 品 和 连 接 装 置 这 些 警 告 事 项 都 按 警 示 程 度 明 示 出 等 级 有 资 格 的 人 员 : YO-YO 只 能 进 行 与 手

More information

CANVIO_AEROCAST_CS_EN.indd

CANVIO_AEROCAST_CS_EN.indd 简 体 中 文...2 English...4 SC5151-A0 简 体 中 文 步 骤 2: 了 解 您 的 CANVIO AeroCast CANVIO AeroCast 无 线 移 动 硬 盘 快 速 入 门 指 南 欢 迎 并 感 谢 您 选 择 TOSHIBA 产 品 有 关 您 的 TOSHIBA 产 品 的 详 情, 请 参 阅 包 含 更 多 信 息 的 用 户 手 册 () 安

More information

AS4610 Series QSG-EN_SC_TC R02.book

AS4610 Series QSG-EN_SC_TC R02.book Quick Start Guide 4/48-Port GE Data Center Switch AS460-0T AS460-0P AS460-54T AS460-54P. Unpack the Switch and Check Contents AS460-0T AS460-0P Note: The switch can also be installed on a desktop or shelf

More information

Microsoft Word SSA4.doc

Microsoft Word SSA4.doc 2014-04-30 5012604904-SSA4 POWER RUN ERROR COM1 RUN STOP X0 X2 X3 X4 X5 X6 X7 C0 Y0 Y1 Y2 Y3 SG X1 COM3+ COM3- COM1 ENGLISH Thank you for choosing Delta DVP-SA2. DVP-SA2 is a 12-point (8DI + 4DO) PLC MPU,

More information

HC70245_2008

HC70245_2008 Reliability Laboratory Page: 1 of 6 Date: September 5, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Microsoft Word SX21.doc

Microsoft Word SX21.doc 2011-04-12 5011696701-SX21.... DVP-1150070-02 VI2- V0+ I0+ VI0- V1+ I1+ VI1- V2+ I2+ I3+ VI3- V3+ FE VO0 IO0 VO1 IO1 AG ENGLISH Thank you for choosing Delta DVP-SX2. DVP-SX2 is a 20-point (8DI + 6 DO +

More information

Microsoft Word - LD5515_5V1.5A-DB-01 Demo Board Manual

Microsoft Word - LD5515_5V1.5A-DB-01 Demo Board Manual Subject LD5515 Demo Board Model Name (5V/1.5A) Key Features Built-In Pump Express TM Operation Flyback topology with PSR Control Constant Voltage Constant Current High Efficiency with QR Operation (Meet

More information

Microsoft Word - HC20138_2010.doc

Microsoft Word - HC20138_2010.doc Page: 1 of 7 Date: April 26, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

WVT new

WVT new Operating and Installation Instructions 5120 004601 (PD 84 09 25) Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser

HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser E915 1 HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser SIMPLE ND EFFETIVE Easy-Laser D23 Easy-Laser E5 TEHNIL DT System Relative humidity 10 95% (complete system) 12.1 kg [26.7 lbs] arrying

More information

Microsoft PowerPoint - ATF2015.ppt [相容模式]

Microsoft PowerPoint - ATF2015.ppt [相容模式] Improving the Video Totalized Method of Stopwatch Calibration Samuel C.K. Ko, Aaron Y.K. Yan and Henry C.K. Ma The Government of Hong Kong Special Administrative Region (SCL) 31 Oct 2015 1 Contents Introduction

More information

LSC操作说明

LSC操作说明 1 C H R I S T A L P H A 1-4 LSC 型 Part. No. 102041 A L P H A 2-4 LSC 型 Part. No. 10204 冷 冻 干 燥 机 操 作 说 明 新 研 制 的 LSC-8 控 制 器, 具 备 图 形 显 示 功 能, 能 以 数 据 表 形 式 显 示 参 数, 并 可 选 配 控 制 软 件 LSC-8 1/4 VGA 大 屏 幕

More information

WFC40810

WFC40810 9000086873 (PD 85 05 10) Operating and Installation Instructions Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

Microsoft Word E203_TSE.doc

Microsoft Word E203_TSE.doc 2011-04-12 5011685804-E204 DVP-1130070-02 ENGLISH Thank you for choosing Delta s DVP-ES2 series PLC. DVP-ES2 series provides 16~ 60 points MPU and 8 ~ 32 points digital I/O module. The maximum I/O points

More information

接线端子--Connectors规格书.doc

接线端子--Connectors规格书.doc Connectors with/without wire protector high-temperature resistant* High grade flexible strips Resistant to temperature up to 100 C (to 140 C) Multiple approvals Raised base Available with or without wire

More information

Microsoft Word SX24.doc

Microsoft Word SX24.doc 2014-06-04 5011696704-SX24 VI2- V0+ I0+ VI0- V1+ I1+ VI1- V2+ I2+ I3+ VI3- V3+ FE VO0 IO0 VO1 IO1 AG ENGLISH Thank you for choosing Delta DVP-SX2. DVP-SX2 is a 20-point (8DI + 6 DO + 4AI + 2AO) PLC MPU,

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

Microsoft Word _unmarked_.doc

Microsoft Word _unmarked_.doc 2014-07-02 5012618501-5201 ENGLISH EN DVPSCM52-SL is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity, electric shock and vibration. To prevent non-maintenance

More information

錄...1 說...2 說 說...5 六 率 POST PAY PREPAY DEPOSIT 更

錄...1 說...2 說 說...5 六 率 POST PAY PREPAY DEPOSIT 更 AX5000 Version 1.0 2006 年 9 錄...1 說...2 說...3...4 說...5 六...6 6.1 率...7 6.2 POST PAY...8 6.3 PREPAY DEPOSIT...9 6.4...10 6.5...11 更...12...12 LCD IC LED Flash 更 兩 RJ11 ( ) DC ON OFF ON 狀 狀 更 OFF 復 狀 說

More information

2/80 2

2/80 2 2/80 2 3/80 3 DSP2400 is a high performance Digital Signal Processor (DSP) designed and developed by author s laboratory. It is designed for multimedia and wireless application. To develop application

More information

ch_code_infoaccess

ch_code_infoaccess 地 產 代 理 監 管 局 公 開 資 料 守 則 2014 年 5 月 目 錄 引 言 第 1 部 段 數 適 用 範 圍 1.1-1.2 監 管 局 部 門 1.1 紀 律 研 訊 1.2 提 供 資 料 1.3-1.6 按 慣 例 公 布 或 供 查 閱 的 資 料 1.3-1.4 應 要 求 提 供 的 資 料 1.5 法 定 義 務 及 限 制 1.6 程 序 1.7-1.19 公 開 資

More information

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt E15-3D1 Compact 4-Way Cassette type MMU-AP0071MH2UL MMU-AP0091MH2UL MMU-AP0121MH2UL MMU-AP0151MH2UL MMU-AP0181MH2UL Contents 1. Specifications 2. Dimensions 3. Center of gravity 4. Piping diagram 5. Wiring

More information

Resistors - All Resistors - Chip Resistors

Resistors - All Resistors - Chip Resistors THICK FILM CHIP RESISTORS 特性 (Features) 輕薄短小 : 小型輕量, 大幅縮小 PC 板面積及重量 Small size and ligtweight with size range per int'l standard 裝配性佳 : 外觀均勻精確, 易於裝配 Highly stable in auto-placement surface mounting application

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER L Series Features Coaxial shaft series L series Helical gears contribute to reduce vibration and noise. Standard backlash is 5 arc-min, ideal for precision control. High rigidity

More information

LH_Series_Rev2014.pdf

LH_Series_Rev2014.pdf REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check

More information

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin.

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin. Features Wide 3.6V to 32V Input Voltage Range Output Adjustable from 0.8V to 30V Maximum Duty Cycle 100% Minimum Drop Out 0.6V Fixed 300KHz Switching Frequency 12A Constant Output Current Capability Internal

More information

Microsoft Word - AP1515V02

Microsoft Word - AP1515V02 Document No. Rev.: V0.20 Page: 1 of 9 Revision History Rev. DRN # History Initiator Effective Date V01 V02 Initial document 黃宗文 Add second package description 葉宗榮 2014/05/15 2015/09/08 Initiator: 雷晨妤 (DCC)

More information

audiogram3 Owners Manual

audiogram3 Owners Manual USB AUDIO INTERFACE ZH 2 AUDIOGRAM 3 ( ) * Yamaha USB Yamaha USB ( ) ( ) USB Yamaha (5)-10 1/2 AUDIOGRAM 3 3 MIC / INST (XLR ) (IEC60268 ): 1 2 (+) 3 (-) 2 1 3 Yamaha USB Yamaha Yamaha Steinberg Media

More information

MT5V4Borchure.cdr

MT5V4Borchure.cdr EasyView 觸控科技 引領未來 MT 500 Professional Human Machine Interface Touch Screen for Industrial Applications ISO 9001:000 Offline Simulator EasyBuilder Online Simulator MT500 Online Simulator Direct Online

More information

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E Gerotor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 5 5 1 0 1 0 3 3 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 25mm Keyed (A) 1.0' 6T Spline

More information

操作指导手册

操作指导手册 GLI P53 C P53 ph/orp 1 Adobe Acrobat GLI gliint.com GLI GLI Adobe Adobe adobe.com 2 FMRC 3600 3611 3810 CSA C22.2 142 C22.2 213 EN 61010-1 TB2 TB3 1 2 3 70 3 GLI P53 GLI GLI GLI GLI GLI GLI 4 GLI ph ph

More information

ARK-14013/14017/14018

ARK-14013/14017/14018 ARK-24017F 8 ARK-24017F : 8 2 ii 1997~2000,,,,,, 1...3 1.1 ARK...3 1.2 ARK-24017F...3 ARK-24017F?...3 ARK-24017F...3 ARK-24017F...3 ARK-24017F...5 ARK-24017F...6...7 2.1...7 2.2...7 ARK...7...8...8...8...9

More information

VASP应用运行优化

VASP应用运行优化 1 VASP wszhang@ustc.edu.cn April 8, 2018 Contents 1 2 2 2 3 2 4 2 4.1........................................................ 2 4.2..................................................... 3 5 4 5.1..........................................................

More information

FM1935X智能非接触读写器芯片

FM1935X智能非接触读写器芯片 FM33A0xx MCU 2017. 05 2.0 1 (http://www.fmsh.com/) 2.0 2 ... 3 1... 4 1.1... 4 1.2... 4 1.3... 5 1.3.1... 5 1.3.2... 5 1.4... 8 1.4.1 LQFP100... 8 1.4.2 LQFP80... 9 1.4.3... 9 2... 15 2.1 LQFP100... 15

More information

2007 : 98 :0532-86894022.86891404 :0532-86880184 :266555 : 726 ( 4 41 ) :0552-4910760 :0552-4911181 :233006 1.... 3 2.... 3 2.1... 3 2.2... 4 3.... 4 3.1... 4 3.2... 9 3.3... 12 3.4... 16 3.5... 17 3.6...

More information

t70.0101gb.fm

t70.0101gb.fm 数 据 单 70.3590 页 码 / JIMAGO 500 / JIMAGO 500 703590/... 5 7 3 0 40 V AC 0 30 V AC/DC COM SETUP/RS4/485 8 50 6 000 4 6 COM RS4/485 ER8 PROFIBUSDP ProfibusDP 5 6 7 ( ) ( ) ( ) 0/5V Modem 0/V ( ) SETUP Windows95/98/NT4.0/000/ME/XP/Vista

More information

HC70044_2008

HC70044_2008 Page: 1 of 9 Date: July 10, 2008 KORENIX TECHNOLOGY CO., LTD. 9 F, NO. 100-1, MING-CHUAN RD., SHIN TIEN CITY, TAIPEI, TAIWAN The following merchandise was submitted and identified by the vendor as: Product

More information

ESD.xls

ESD.xls Transient Suppressor Reverse Reverse ESD Capacitance Stand-off Beakdown Package Contact/Air Channel Circuit Diagram Pin Configuration Remark CMTLCP020CR35BFE CMTLDF02CR35AFE CMTLDF02CR50BLE CSP020 (pf)

More information

OR-3655 3655 O 2 H 2 31673 3655 1 3655 31673 3655/xxx 31110A 31120A 31230 xxx=111 xxx=210 31110A 31120A 31230 32007D Delrin WinLog97 PC 32689 CD 2 2 EC 3655 OM E0307.fm 3655 EC 3655 ppm ppb g/kg mg/l

More information

Microsoft Word - PLC與GP接線說明_缺WDH_2.doc

Microsoft Word - PLC與GP接線說明_缺WDH_2.doc PC 與 HMI 下載線路圖 HMI PC 1 RS422 R+ 2 RS232 RX 3 RS232 TX 2 RS232 RX 3 RS232 TX 4RS485 D+/RS422 T+ 6 RS422 R- 7 RS232 RTS 8 RS232 CTS 7 RS232 RTS 8 RS232CTS 9RS485 D-/RS422 T- SH( 外殼 ) DB9( 母 ) 接頭 SH( 外殼

More information

Thin Film Precision Temperature Chip Resistor TPT 2013.xls

Thin Film Precision Temperature Chip Resistor TPT 2013.xls FEATURE Thin Film Passivity NiCr Resistor Very Tight Tolerance from ±0.01%. Extremely Low TCR from ±5ppm/ Wide R-Value Range Rated : 1/32W ~ 1W (0402 ~2512) Applications Medical Equipment Testing / Measurement

More information

SDP 1 2 3 4 8 9 10 12 19

SDP 1 2 3 4 8 9 10 12 19 SDP SDP 1 2 3 4 8 9 10 12 19 SDP 2 SDP CANBUS 3m/s 48 1 2 N 3 4 5 6 7 8 9 EMC EMC ENS008212 EN618003 10 IP21 SDP 3 1 1 4 2 5 3 P24 103 104 N24 G24 P24 101 102 N24 G24 J2 J3 n P2 P1 P3 J2 J1 J3 1 P2 P1

More information

HC20093A_2008

HC20093A_2008 Reliability Laboratory Page: 1 of 6 Date: March 5, 2008 KORENIX TECHNOLOGY., CO. FL 9, NO. 100-1, MIN-CHUAN RD. SHING TIEN CITY, TAIPEI, TAIWAN The following merchandise was submitted and identified by

More information

SRD-N/TRD-N DIMENSIONS 規格尺寸 SRD-N SRD-N + PF08A + FH- 2 UNIT :mm TRD-N TRD-N + 8PFA 101 SRD-N/TRD-N POWER OPERATION 操作方式 4

SRD-N/TRD-N DIMENSIONS 規格尺寸 SRD-N SRD-N + PF08A + FH- 2 UNIT :mm TRD-N TRD-N + 8PFA 101 SRD-N/TRD-N POWER OPERATION 操作方式 4 STON STAR-DELTA TIMER SRD-N/TRD-N 馬達啟動器 SRD-N ORDERING INFORMATION 訂購說明 TRD-N Ex S RDN 0S A220 CE Approved. STON or P&B RELAY inside. MOTOROLA IC inside. Standard change time is 0.1Seconds. CE 認證 內部採用美國第一品牌

More information

RS-232C [11-13] 1 1 (PLC) (HMI) Visual Basic (PLC) 402

RS-232C [11-13] 1 1 (PLC) (HMI) Visual Basic (PLC) 402 年 路 年 1 [1-3][4] [5-7] [15] Visual Basic [10] 401 RS-232C [11-13] 1 1 (PLC) (HMI) Visual Basic (PLC) 402 1 1 X0 X1 X2 X3 SENSOR Y0 SENSOR VB X3 Y0 Y1 Y2 Y3 Y4 Y5 Y1~Y5 Y6 VB Y7 VB Y11 Y12 Y13 Y14 Y15 Y11~Y15

More information

VioCard-300 user manual

VioCard-300 user manual VioGate VioCard-300 ( 2.0.0) 2005 2005 2 15 2 3 VioGate 绍... 6 1.1 产 简... 6 1.2 产... 6 1.3... 7 1.4 内... 7 1.5 导览... 8 VioGate... 10 2.1 VioGate 络 认...10 2.2 VioGate...11 软... 16 3.1 VioCard-300 盘...16

More information

Induction Heating and Melting Capacitors

Induction Heating and Melting Capacitors General Information Induction Heating and Melting Capacitors pplication: The capacitors are applicable for indoor use and intended to be used for power factor correction in induction heating, melting,

More information

Guide to Install SATA Hard Disks

Guide to Install SATA Hard Disks SATA RAID 1. SATA. 2 1.1 SATA. 2 1.2 SATA 2 2. RAID (RAID 0 / RAID 1 / JBOD).. 4 2.1 RAID. 4 2.2 RAID 5 2.3 RAID 0 6 2.4 RAID 1.. 10 2.5 JBOD.. 16 3. Windows 2000 / Windows XP 20 1. SATA 1.1 SATA Serial

More information

2.PFA 사출 Valve 지윤주

2.PFA 사출 Valve 지윤주 IF Series -urbin ype Digital Flowmeter D I 4-20mA 4-20mA [ 分离型 ] C A [ 一体型 ] Specification () ) ()( ) ()( ) (Max. p. Press)( ) (Max. p. emp)( ) (viscosity)( ) (Used Fluid)( ) - PC, PF, - - - 4~20mA - -

More information

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp GC-ALPINE RIDGE Installation Guide/ 12WE6-ALPINER-10AR Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2),

More information

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E Gerolor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 12 12 1 1 0 0 2 2 31 31 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 2mm Keyed (A) 1.0'

More information

DR2010.doc

DR2010.doc DR/2010 HACH 11-8-96-2 HACH. DR/2010, / UL E79852 CSA C22.223 LR 58275 VDE GS 1015-92 FCC"A" 15 : AMADOR CORP, HACH. EN50 011/CISPR 11 "B" (EMI)/89/336/EEC/EMC: AMADOR CORP, HACH.. EN50 082-1( )/89/226/EEC

More information

Comp-AC ACS to 2.2 kw

Comp-AC ACS to 2.2 kw Comp-AC ACS100 0.12 to 2.2 kw ACS 100 3BFE 64307622 R0125 3ABD00008839 C 2002 11 20 2000 ABB Industry Oy ACS 100 5 (U c+, U c- ) G! (U1, V1, W1 U2, V2, W2 U c+, U c- )! ACS400 ( RO1, RO2, RO3)! ACS100!

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER SSeries Coaxial shaft series Features S series Standard backlash is 3 arc-min, ideal for precision control. High rigidity & high torque were achived by uncaged needle roller

More information

(Load Project) (Save Project) (OffLine Mode) (Help) Intel Hex Motor

(Load Project) (Save Project) (OffLine Mode) (Help) Intel Hex Motor 1 4.1.1.1 (Load) 14 1.1 1 4.1.1.2 (Save) 14 1.1.1 1 4.1.2 (Buffer) 16 1.1.2 1 4.1.3 (Device) 16 1.1.3 1 4.1.3.1 (Select Device) 16 2 4.1.3.2 (Device Info) 16 2.1 2 4.1.3.3 (Adapter) 17 2.1.1 CD-ROM 2 4.1.4

More information

FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC D

FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC D 2006 4 27 1 JY FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC DC FILTRON AC 24VAC 24VAC AC 24VAC AC

More information

Three Point Inside Micrometers

Three Point Inside Micrometers 三點式內徑測微器 ( 刻劃式 ) Three Point Inside Micrometer (Vernier) TP-9006 TP-9008 TP-9010 TP-9012 TP-9016 TP-9020 TP-9025 TP-9030 TP-9040 TP-9050 TP-9062 TP-9075 TP-9087 6-8mm 8-10mm 10-12mm 12-16mm 16-20mm 20-25mm

More information

SA-DK2-U3Rユーザーズマニュアル

SA-DK2-U3Rユーザーズマニュアル USB3.0 SA-DK2-U3R 2007.0 2 3 4 5 6 7 8 System Info. Manual Rebuild Delete RAID RAID Alarm Rebuild Rate Auto compare Temp Management Load Default Elapse time Event Log 0 2 3 4 2 3 4 ESC 5

More information

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 FR-N3X WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 CT-3 CLASS LASER PRODUCT CT-4 CT-5 6 mm mm 3 mm 6 5mm 2 CT-6 2 CT-7 2 3 0mm

More information

未命名-2

未命名-2 ELECTRIC CORPORATION 01 847-478-2253 02 638-7072 0 21 02 4 86-1 12 0 27 11 444-0223 01707 278-695???????? 1 DIN LED Munsell0.08GY17.64/0.81 PC LED DIN ( 35 ) DIN AT

More information