CDX-R3410S/R3410

Transcription

1 (1) FM/AM Compact Disc Player Autoestéreo para disco compacto Operating Instructions Manual de instrucciones GB ES CT For installation and connections, see the supplied installation/connections manual. Para obtener información sobre la instalación y las conexiones, consulte el manual de instalación/conexiones suministrado. CDX-R3410S CDX-R Sony Corporation

2 Welcome! Thank you for purchasing this Sony Compact Disc Player. You can enjoy your drive with the following functions. CD playback: You can play CD-DA (also containing CD TEXT*), CD-R/CD-RW (MP3 files also containing Multi Session (page 13)) and ATRAC CD (ATRAC3 and ATRAC3plus format (page 13)). Type of discs Label on the disc Warning if your car s ignition has no ACC position After turning the ignition off, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain. CD-DA MP3 ATRAC CD Radio reception: You can store up to 6 stations per band (FM1, FM2, FM3, AM1 and AM2). BTM (Best Tuning Memory) function: the unit selects strong signal stations and stores them. You can assign a name to each radio station, store it in memory, and display station names on the list. Optional unit operation You can also control optional CD/MD changers, in addition to playing with this unit. * A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name. This label is located on the bottom of the chassis. CAUTION The use of optical instruments with this product will increase eye hazard. SonicStage and its logo are trademarks of Sony Corporation. ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation. 2

3 Table of Contents Getting Started Resetting the unit Setting the clock DEMO mode Detaching the front panel Attaching the front panel Inserting the disc in the unit Ejecting the disc Location of controls and basic operations CD Main unit Card remote commander RM-X Display items Repeat and shuffle play Radio Storing and receiving stations Storing automatically BTM Storing manually Receiving the stored stations Tuning automatically Receiving a station through a list list-up Other functions Changing the sound settings Adjusting the sound characteristics BAL/FAD/SUB Adjusting the equalizer curve EQ Labelling a station/disc Adjusting setup items SET Using optional equipment CD/MD changer Rotary commander RM-X4S Additional Information Precautions Notes on discs About MP3 files About ATRAC CD Maintenance Removing the unit Specifications Troubleshooting Error displays/messages

4 Getting Started Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Detach the front panel and press the RESET button with a pointed object, such as a ballpoint pen. RESET button Note Pressing the RESET button will erase the clock setting and some stored contents. Detaching the front panel You can detach the front panel of this unit to prevent theft. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. 1 Press (OFF). The unit is turned off. 2 Press, then pull it off towards you. (OFF) Setting the clock The clock uses a 12-hour digital indication. 1 Press and hold (SEL). The setup display appears. 2 Press (SEL) repeatedly until CLOCK- ADJ appears. 3 Press (DSPL). The hour indication flashes. 4 Press the volume +/ button to set the hour and minute. To move the digital indication, press (DSPL). 5 Press (SEL). The clock starts and the next setup display appears. 6 Press and hold (SEL). The setup is complete. To display the clock, press (DSPL). Press (DSPL) again to return to the previous display. With the card remote commander In step 4, to set the hour and minute, press M or m. Notes Do not drop or put excessive pressure on the front panel and display window. Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Tip When carrying the front panel, use the supplied front panel case. Attaching the front panel Engage part A of the front panel with part B of the unit, as illustrated, and push the left side into position until it clicks. DEMO mode When the unit is turned off, the clock is displayed first, then demonstration (DEMO) mode starts the demonstration display. To cancel the DEMO mode, set DEMO-OFF in setup (page 10) while the unit is turned off. A B 4 Note Do not put anything on the inner surface of the front panel.

5 Inserting the disc in the unit 1 Open the shutter. Ejecting the disc 1 Open the shutter. 2 Insert the disc label side up. x Playback starts. 3 Close the shutter. 2 Push down the shutter until it clicks. Click x The disc is ejected. Notes While ejecting or inserting the disc, do not close the shutter. The disc may be caught and damaged. The disc may be ejected if you open the shutter forcefully. Tip The disc can be played with the shutter opened or closed. 5

6 Location of controls and basic operations Main unit ATT OFF OPEN DSPL DIM EQ3 SEEK GP/DISC + REP SHUF BTM SOURCE MODE SEL SENS SCRL LIST CDX-R3410S 9 0 qaqs qd qf qg qh qj qk CDX-R3410 ql Card remote commander RM-X w; OFF SOURCE SEL ATT MODE 2 qs qa 3 DSPL + SCRL ws qj wd wa + VOL 6

7 Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. a Volume +/ button To adjust volume. b ATT (attenuate) button To attenuate the sound. To cancel, press again. c DSPL (display)/dim (dimmer) button 4, 8, 10 To change display items (press); change the display brightness (press and hold). d OPEN shutter, disc slot (located behind the shutter) 5 e Display window f EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF). g OFF button To power off/stop the source. h SEEK +/ button Radio: To tune in stations automatically (press); find a station manually (press and hold). CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/ reverse a track (press and hold). i (front panel release) button 4 j SOURCE button To power on/change the source (Radio/CD/ MD* 1 ). k MODE button 8, 11 To select the radio band (FM/AM)/select the unit* 2. l SEL (select) button 4, 9, 10 To select items. m RESET button (located behind the front panel) 4 n Frequency select switch (located on the bottom of the unit) See Frequency select switch in the supplied installation/connections manual. o Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD/MD* 1 : (1)/(2): GP* 3 /DISC* 2 /+ To skip groups (press); skip groups continuously (press and hold). (3): REP 8 (4): SHUF 8 p SENS/BTM button 8 To improve weak reception: LOCAL/MONO (press); start the BTM function (press and hold). q SCRL button 8 To scroll the display item. r LIST button 9, 11 To list up. s Receptor for the card remote commander The following buttons on the card remote commander have also different buttons/functions from the unit. t < (.)/, (>) buttons To control radio/cd, the same as (SEEK) +/ on the unit. (For details of other operations, see With the card remote commander on each pages.) u VOL +/ button To adjust volume. v M (+)/m ( ) buttons To control CD, the same as (1)/(2) /+ on the unit. (For details of other operations, see With the card remote commander on each pages.) w Number buttons To receive stored stations (press); store stations (press and hold). *1 When an MD changer is connected. *2 When a CD/MD changer is connected. *3 When an MP3/ATRAC CD is played and a changer is not connected. If the changer is connected, the operation is different, see page 11. Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see Replacing the lithium battery of the card remote commander on page 14. 7

8 CD For details on connecting to a CD/MD changer, see page 11. Display items A B Radio Storing and receiving stations Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. 8 A Source B Track number/elapsed playing time, Disc/artist name, Group number* 1, Group name, Track name, Text information* 2, Clock *1 Group number is displayed only when the group is changed. *2 When playing an MP3, ID3 tag is displayed and when playing a ATRAC CD, text information written by SonicStage, etc. is displayed. To change display items B, press (DSPL); scroll display items B, press (SCRL) or set A.SCRL-ON (page 10). Tip Displayed item will differ, depending on the disc type and recorded format. For details on MP3, see page 13; ATRAC CD, see page 13. Repeat and shuffle play 1 During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears. Select REP-TRACK REP-GP* SHUF-GP* SHUF-DISC To play track repeatedly. group repeatedly. group in random order. disc in random order. * When an MP3/ATRAC CD is played. To return to normal play mode, select REP- OFF or SHUF-OFF. Storing automatically BTM 1 Press (SOURCE) repeatedly until TUNER appears. To change the band, press (MODE) repeatedly. You can select from FM1, FM2, FM3, AM1 or AM2. 2 Press and hold (BTM) until BTM flashes. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored. Storing manually 1 While receiving the station that you want to store, press and hold a number button ((1) to (6)) until MEM appears. The number button indication appears in the display. Note If you try to store another station on the same number button, the previous stored station will be replaced. Receiving the stored stations 1 Select the band, then press a number button ((1) to (6)). With the card remote commander To select preset stations, press M or m. Tuning automatically 1 Select the band, then press (SEEK) +/ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold (SEEK) +/ to locate the approximate frequency, then press (SEEK) +/ repeatedly to fine adjust to the desired frequency (manual tuning).

9 Receiving a station through a list list-up You can list up the frequency or the name. For details on labelling a station, see page Select the band, then press (LIST). The frequency or station name appears. 2 Press (LIST) repeatedly until the desired station appears. After 5 seconds, the unit returns to normal reception mode. 3 Press (SEEK) +/ to receive the station. With the card remote commander In step 2, to select the station, press M or m. Other functions Changing the sound settings Adjusting the sound characteristics BAL/FAD/SUB You can adjust the balance, fader, and subwoofer volume. 1 Press (SEL) repeatedly until BAL, FAD or SUB appears. The item changes as follows: LOW* 1 t MID* 1 t HI* 1 t BAL (left-right) t FAD (front-rear) t SUB (subwoofer volume)* 2 *1 When EQ3 is activated (page 9). *2 When the audio output is set to SUB (page 10). ATT is displayed at the lowest setting, and can be adjusted up to 20 steps. 2 Press the volume +/ button repeatedly to adjust the selected item. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Note Adjust within 3 seconds of selecting the item. With the card remote commander In step 2, to adjust the selected item, press <, M,, or m. Adjusting the equalizer curve EQ3 You can adjust and store the equalizer settings for different tone ranges. 1 Select a source, then press (EQ3) repeatedly to select the EQ3 type. 2 Press (SEL) repeatedly until LOW, MID or HI appears. 3 Press the volume +/ button repeatedly to adjust the selected item. The volume level is adjustable in 1 db steps, from 10 db to +10 db. Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold (SEL) before the setting is complete. continue to next page t 9

10 10 After 3 seconds, the setting is complete and the display returns to normal play/reception mode. With the card remote commander In step 3, to adjust the selected item, press <, M,, or m. Labelling a station/disc When you receive a station, or play a disc in a CD changer with the CUSTOM FILE function, you can label each station/disc with a custom name up to 8 characters (Station Memo/Disc Memo). If you label a station/disc, the name appears on the list (page 9 or 11). 1 While receiving a station or playing a disc that you want to label, press and hold (LIST). 2 Press the volume +/ button repeatedly until the desired character appears. To move the digital indication, press (SEL). A y B y C... y 0 y 1 y 2... y + y y... y (blank space) y A Repeat this operation until the entire name is entered. 3 Press and hold (LIST). The labelling is complete and the display returns to normal play/reception mode. To display the name, press (DSPL) during reception or playback. Tips To correct or erase a character, overwrite or enter. The Disc Memo always takes priority over any prerecorded title. You can label a disc on the unit if a changer with the CUSTOM FILE function is connected. REP-TRACK and all shuffle play are suspended until the labelling is complete. With the card remote commander In step 2, to select the character, press M or m. Deleting the custom name 1 Select the radio, or the unit that has stored the custom name you want to delete, then press and hold (LIST). 2 Press and hold (DSPL). The stored name will flash. 3 Press the volume +/ button repeatedly to select the name you want to delete. 4 Press and hold (SEL). The name is deleted. Repeat steps 3 and 4 to delete other names. 5 Press and hold (LIST). The unit returns to normal play/reception mode. With the card remote commander In step 3, to select the name, press M or m. Adjusting setup items SET 1 Press and hold (SEL). The setup display appears. 2 Press (SEL) repeatedly until the desired item appears. 3 Press the volume +/ button to select the setting (example ON or OFF ). 4 Press and hold (SEL). The setup is complete and the display returns to normal play/reception mode. Note Displayed items will differ, depending on the source and setting. With the card remote commander In step 3, to select the setting, press < or,. The following items can be set (follow the page reference for details): z indicates the default settings. CLOCK-ADJ (Clock Adjust) BEEP SUB/REAR* 1 (page 4) To set BEEP-ON (z) or BEEP-OFF. To switch the audio output. SUB (z): to output to a subwoofer. REAR : to output to a power amplifier. DIM (Dimmer) To change the brightness of the display. DIM-ON : to dim the display. DIM-OFF (z): to deactivate the dimmer. DEMO* 1 To set DEMO-ON (z) or (Demonstration) DEMO-OFF (page 4). A.SCRL (Auto Scroll) To scroll long displayed items automatically when the group/ track is changed. A.SCRL-ON : to scroll. A.SCRL-OFF (z): to not scroll.

11 LPF* 2 (Low Pass Filter) *1 When the unit is turned off. *2 When the audio output is set to SUB. Using optional equipment CD/MD changer Selecting the changer To select the cut-off frequency 78HZ, 125HZ or OFF (z). 1 Press (SOURCE) repeatedly until CD or MD appears. 2 Press (MODE) repeatedly until the desired changer appears. Unit number Disc number Tip SHUF-ALL will not shuffle tracks between CD units and MD changers. Locating a disc by name list-up You can select a disc from the list when connecting a CD changer with the CUSTOM FILE function or an MD changer. If you assign a name to a disc, the name appears on the list. For details on labelling a disc, see page During playback, press (LIST). The disc number or disc name appears. 2 Press (LIST) repeatedly until the desired disc appears. After 5 seconds, the unit returns to normal play mode. 3 Press (SEEK) +/ to play the disc. With the card remote commander In step 2, to select the disc, press M or m. Playback starts. Skipping groups and discs 1 During playback, press (1)/(2) (GP/DISC) /+. To skip Press (1)/(2) group group continuously discs discs continuously and release (hold for a moment). within 2 seconds of first releasing. repeatedly. then, press again within 2 seconds and hold. Repeat and shuffle play 1 During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears. Select REP-DISC* 1 SHUF- CHGR* 1 SHUF-ALL* 2 To play disc repeatedly. tracks in the changer in random order. tracks in all units in random order. *1 When one or more CD/MD changers are connected. *2 When one or more CD changers, or two or more MD changers are connected. To return to normal play mode, select REP- OFF or SHUF-OFF. Rotary commander RM-X4S Attaching the label Attach the indication label depending on how you mount the rotary commander. SEL MODE DSPL Location of controls The corresponding buttons on the rotary commander control the same functions as those on this unit. SOURCE PRESET VOL SEL DSPL MODE SEL ATT DSPL SEEK/AMS MODE OFF continue to next page t OFF 11

12 The following controls on the rotary commander require a different operation from the unit. PRESET control To select preset stations; control CD, the same as (1)/(2) /+ on the unit (push in and rotate). VOL control The same as the volume +/ button on the unit (rotate). SEEK/AMS control The same as (SEEK) +/ on the unit (rotate, or rotate and hold). Changing the operative direction The operative direction of the controls is factoryset as shown below. To increase To decrease If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. 1 While pushing the VOL control, press and hold (SEL). Additional Information Precautions If your car has been parked in direct sunlight, allow the unit to cool off before operating it. Power aerial will extend automatically while the unit is operating. Moisture condensation On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. To maintain high sound quality Be careful not to splash juice or other soft drinks onto the unit or discs. Notes on discs To keep a disc clean, do not touch its surface. Handle the disc by its edge. Keep your discs in their cases or disc magazines when not in use. Do not subject discs to heat/high temperature. Avoid leaving them in a parked car or on a dashboard/rear tray. Do not attach labels, or use discs with sticky ink/residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc. Do not use any discs with labels or stickers attached. The following malfunctions may result from using such discs: Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism). Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp. Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs. You cannot play 8 cm CDs. 12

13 Before playing, clean the discs with a commercially available cleaning cloth. Wipe each disc from the centre out. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue discs. Notes on CD-R/CD-RW discs Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. You cannot play a CD-R/a CD-RW that is not finalized. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. About MP3 files MP3, which stands for MPEG-1 Audio Layer-3, is a music file compression format standard. It compresses audio CD data to approximately 1/10 of its original size. The unit is compatible with the ISO 9660 level 1/level 2 format, Joliet/Romeo in the expansion format, ID3 tag version 1.0, 1.1, 2.2, 2.3 and 2.4, and Multi Session. The maximum number of: folders (groups): 150 (including root and empty folders). MP3 files (tracks) and folders contained in a disc: 300 (if a folder/file names contain many characters, this number may become less than 300). displayable characters for a folder/file name is 32 (Joliet), or 32/64 (Romeo); ID3 tag is 15/30 characters (1.0, 1.1, 2.2 and 2.3), or 63/ 126 characters (2.4). Playback order of MP3 files MP3 Notes Be sure to finalize the disc before using on the unit. When naming an MP3 file, be sure to add the file expansion.mp3 to the file name. If you play a high-bit-rate MP3, such as 320 kbps, sound may be intermittent. During playback of a VBR (variable bit rate) MP3 file or fast-forward/reverse, elapsed playing time may not display accurately. When the disc is recorded in Multi Session, only the first track of the first session format is recognized and played (any other format is skipped). The priority of the format is CD-DA, ATRAC CD and MP3. When the first track is a CD-DA, only CD-DA of the first session is played. When the first track is not a CD-DA, an ATRAC CD or MP3 session is played. If the disc has no data in any of these formats, NO MUSIC is displayed. About ATRAC CD Folder (group) MP3 file (track) ATRAC3plus format ATRAC3, which stands for Adaptive Transform Acoustic Coding3, is audio compression technology. It compresses audio CD data to approximately 1/10 of its original size. ATRAC3plus, which is an extended format of ATRAC3, compresses the audio CD data to approximately 1/20 of its original size. The unit accepts both ATRAC3 and ATRAC3plus format. ATRAC CD ATRAC CD is recorded audio CD data which is compressed to ATRAC3 or ATRAC3plus format using authorized software, such as SonicStage 2.0 or later, or SonicStage Simple Burner. The maximum number of: folders (groups): 255 files (tracks): 999 The characters for a folder/file name and text information written by SonicStage is displayed. For details on ATRAC CD, see the SonicStage or SonicStage Simple Burner manual. continue to next page t 13

14 Note Be sure to create the ATRAC CD using authorized software, such as SonicStage 2.0 or later, or SonicStage Simple Burner 1.0 or 1.1, which are supplied with Sony Network products. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 4) and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. Maintenance Replacing the lithium battery of the card remote commander Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the card remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. 1 2 c + side up Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Main unit Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device. Removing the unit Back of the front panel 1 Remove the protection collar. 1Detach the front panel (page 4). 2Engage the release keys together with the protection collar. Orient the release keys as shown. 3Pull out the release keys to remove the protection collar. Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Fuse (10A) 14

15 2 Remove the unit. 1 Insert both release keys simultaneously until they click. 2 Pull the release keys to unseat the unit. 3 Slide the unit out of the mounting. Specifications CD Player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit Tuner section Hook facing inwards. FM Tuning range: MHz (at 50 khz step) MHz (at 200 khz step) FM tuning interval: 50 khz/200 khz switchable Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 khz Usable sensitivity: 9 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 67 db (stereo), 69 db (mono) Harmonic distortion at 1 khz: 0.5 % (stereo), 0.3 % (mono) Separation: 35 db at 1 khz Frequency response: 30 15,000 Hz AM Tuning range: 531 1,602 khz (at 9 khz step) 530 1,710 khz (at 10 khz step) AM tuning interval: 9 khz/10 khz switchable Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 khz Sensitivity: 30 µv Power amplifier section Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) General Outputs: Audio outputs terminal (sub/rear switchable) Power aerial relay control terminal Power amplifier control terminal Inputs: BUS control input terminal BUS audio input terminal Remote controller input terminal Aerial input terminal Tone controls: Low: ±10 db at 60 Hz (XPLOD) Mid: ±10 db at 1 khz (XPLOD) High: ±10 db at 10 khz (XPLOD) Power requirements: 12 V DC car battery (negative earth) Dimensions: Approx mm (w/h/d) Mounting dimensions: Approx mm (w/h/d) Mass: Approx. 1.2 kg Supplied accessories: Card remote commander: RM-X151 Parts for installation and connections (1 set) Front panel case (1) Optional accessories/equipment: Bus cable (supplied with an RCA pin cord): RC-61 (1 m), RC-62 (2 m) CD changer (10 discs): CDX-757MX, CDX-656X MD changer (6 discs): MDX-66XLP Source selector: XA-C30 AUX-IN selector: XA-300 US and foreign patents licensed from Dolby Laboratories. Note This unit cannot be connected to a digital preamplifier or an equalizer which is Sony BUS system compatible. Design and specifications are subject to change without notice. Lead-free solder is used for soldering certain parts. (more than 80 %) Halogenated flame retardants are not used in the certain printed wiring boards. Halogenated flame retardants are not used in cabinets. VOC (Volatile Organic Compound)-free vegetable oil based ink is used for printing the carton. Packaging cushions do not use polystyrene foam. 15

16 16 Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No power is being supplied to the unit. Check the connection. If everything is in order, check the fuse. If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit. The power aerial does not extend. The power aerial does not have a relay box. No sound. The volume is too low. The ATT function is activated. The position of the fader control (FAD) is not set for a 2-speaker system. The CD changer is incompatible with the disc format (MP3/ATRAC CD). t Play back with a Sony MP3 compatible CD changer, or this unit. No beep sound. The beep sound is cancelled (page 10). An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. The RESET button has been pressed. t Store again into the memory. The power connecting lead or battery has been disconnected. The power connecting lead is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition key is switched. The leads are not matched correctly with the car s accessory power connector. The display disappears from/does not appear in the display window. The dimmer is set DIM-ON (page 10). The display disappears if you press and hold (OFF). t Press and hold (OFF) again until the display appears. The connectors are dirty (page 14). CD/MD playback The disc is automatically ejected. The disc has trouble. t Check the following list: The disc cannot be loaded. Another disc is already loaded. The disc has been forcibly inserted upside down or in the wrong way. The disc does not playback. Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 13). MP3 files cannot be played back. The disc is incompatible with the MP3 format and version (page 13). MP3 files take longer to play back than others. The following discs take a longer time to start playback. a disc recorded with a complicated tree structure. a disc recorded in Multi Session. a disc to which data can be added. The ATRAC CD cannot play. The disc is not created by authorized software, such as SonicStage or SonicStage Simple Burner. Tracks that are not included in the group cannot be played. The display items do not scroll. For discs with very many characters, those may not scroll. A.SCRL is set to off. t Set A.SCRL-ON (page 10) or press (SCRL). The sound skips. Installation is not correct. t Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc. The operation buttons do not function. The disc will not eject. Press the RESET button (page 4). Radio reception The stations cannot be received. The sound is hampered by noises. Connect a power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a car s aerial booster (only when your car has built-in FM/AM aerial in the rear/ side glass). Check the connection of the car aerial. The auto aerial will not go up. t Check the connection of the power aerial control lead. Check the frequency. Preset tuning is not possible. Store the correct frequency in the memory. The broadcast signal is too weak.

17 Automatic tuning is not possible. Setting of the local seek mode is not correct. t Tuning stops too frequently: Press (SENS) until LOCAL-ON appears. t Tuning does not stop at a station: Press (SENS) repeatedly until MONO- ON or MONO-OFF (FM), or LOCAL- OFF (AM) appears. The broadcast signal is too weak. t Perform manual tuning. During FM reception, the ST indication flashes. Tune in the frequency accurately. The broadcast signal is too weak. t Press (SENS) to set the monaural reception mode to MONO-ON. An FM programme broadcast in stereo is heard in monaural. The unit is in monaural reception mode. t Press (SENS) until MONO-OFF appears. Error displays/messages BLANK* 1 Tracks have not been recorded on the MD.* 2 Play an MD with recorded tracks. ERROR* 1 The disc is dirty or inserted upside down.* 2 t Clean or insert the disc correctly. The disc cannot play because of some problem. t Insert another disc. FAILURE The speaker/amplifier connection is incorrect. t See the supplied installation/connections manual to check the connection. LOAD The changer is loading the disc. t Wait until loading is complete. L.SEEK +/ The local seek mode is on during automatic tuning. NO DATA All custom names have been deleted, or none are stored. NO DISC The disc is not inserted in the CD/MD changer. t Insert discs in the changer. NO ID3 ID3 tag information is not written in the MP3 file. NO INFO Text information is not written in the ATRAC3/ ATRAC3plus file. NO MAG The disc magazine is not inserted in the CD changer. t Insert the magazine in the changer. NO MUSIC The disc is not a music file. t Insert a music CD in this unit or MP3 playable changer. NO NAME A track/group/disc name is not written in the track. NOT READ The disc information has not been read by the unit. t Loading the disc, then select it on the list. NOTREADY The lid of the MD changer is open or the MDs are not inserted properly. t Close the lid or insert the MDs properly. OFFSET There may be an internal malfunction. t Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. READ The unit is reading all track and group information on the disc. t Wait until reading is complete and playback starts automatically. Depending on the disc structure, it may take more than a minute. RESET The CD unit and CD/MD changer cannot be operated because of some problem. t Press the RESET button (page 4). or During fast-forward or reverse, you have reached the beginning or the end of the disc and you cannot go any further. The character cannot be displayed with the unit. *1 If an error occurs during playback of a CD or MD, the disc number of the CD or MD does not appear in the display. *2 The disc number of the disc causing the error appears in the display. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. 17

18 Bienvenido Gracias por adquirir este reproductor de discos compactos Sony. Mientras conduce puede disfrutar de las funciones siguientes: Reproducción de CD: Puede reproducir CD-DA (que también contengan CD TEXT*), CD-R/CD-RW (archivos MP3 que también incluyan Multi Session (página 13)) y discos ATRAC (formato ATRAC3 y ATRAC3plus (página 14)). Tipo de discos Etiqueta del disco Advertencia: si el encendido del automóvil no dispone de una posición ACC Tras apagar el motor, mantenga presionado (OFF) en la unidad hasta que se apague la pantalla. Si no lo hace, la pantalla no se desactiva y se desgasta la batería. CD-DA MP3 ATRAC CD Esta etiqueta está situada en la parte inferior del chasis. SonicStage y su logotipo son marcas comerciales de Sony Corporation. ATRAC, ATRAC3, ATRAC3plus y sus respectivos logotipos son marcas comerciales de Sony Corporation. Recepción de radio: Puede almacenar hasta 6 emisoras de radio por banda (FM1, FM2, FM3, AM1 y AM2). Función BTM (memoria de emisoras con mejor sintonía): la unidad selecciona las estaciones que emiten la señal más nítida y las almacena. Puede asignar un nombre a cada emisora de radio, guardarlo en la memoria y mostrar los nombres en la lista. Funcionamiento de una unidad opcional Además de reproducir con esta unidad, también puede controlar los cambiadores de CD/MD opcionales. * Un disco CD TEXT es un CD-DA que incluye información como el nombre del disco, del artista y de la pista. 2

19 Tabla de contenido Procedimientos iniciales Restauración de la unidad Ajuste del reloj Modo DEMO Extracción del panel frontal Instalación del panel frontal Inserción del disco en la unidad Expulsión del disco Ubicación de los controles y las operaciones básicas CD Unidad principal Control remoto de tarjeta RM-X Elementos de pantalla Reproducción repetida y aleatoria Radio Almacenamiento y recepción de emisoras Almacenamiento automático BTM Almacenamiento manual Recepción de las emisoras almacenadas... 8 Sintonización automática Sintonización de una emisora mediante una lista Listado Otras funciones Almacenamiento y recepción de emisoras Ajuste de las características del sonido BAL/FAD/SUB Ajuste de la curva de ecualizador EQ Etiquetado de emisora/disco Definición de los elementos de ajuste SET Uso de equipo opcional Cambiador de CD/MD Mando rotatorio RM-X4S Información complementaria Precauciones Notas sobre los discos Acerca de los archivos MP Acerca de discos ATRAC Mantenimiento Extracción de la unidad Especificaciones Solución de problemas Mensajes/indicaciones de error

20 Procedimientos iniciales Restauración de la unidad Antes de utilizar la unidad por primera vez, o después de sustituir la batería del automóvil o de cambiar las conexiones, debe restaurarla. Extraiga el panel frontal y presione el botón RESET con un objeto puntiagudo, como un bolígrafo. Botón RESET Nota Al presionar RESET, se borra el ajuste del reloj y algunos contenidos almacenados. Ajuste del reloj El reloj emplea una indicación digital de 12 horas. 1 Mantenga presionado (SEL). Aparecerá la pantalla de ajustes. 2 Presione (SEL) varias veces hasta que aparezca CLOCK-ADJ. 3 Presione (DSPL). La indicación de la hora parpadea. 4 Presione el botón de volumen +/ para ajustar la hora y los minutos. Para mover la indicación digital, presione (DSPL). 5 Presione (SEL). El reloj se pone en funcionamiento y aparece la pantalla de ajustes siguiente. 6 Mantenga presionado (SEL). Finaliza el ajuste. Para mostrar el reloj, presione (DSPL). Vuelva a presionar (DSPL) para regresar a la pantalla anterior. Con el control remoto de tarjeta En el paso 4, presione M o m para ajustar la hora y los minutos. Modo DEMO Cuando la unidad está apagada, primero se muestra el reloj y, a continuación, el modo de demostración (DEMO) inicia la pantalla respectiva. Para cancelar el modo DEMO, ajuste DEMO- OFF en ajustes (página 11) mientras la unidad está apagada. Extracción del panel frontal Puede extraer el panel frontal de la unidad para evitar que la roben. Alarma de precaución Si gira el interruptor de encendido hasta la posición OFF sin haber extraído el panel frontal, la alarma de precaución sonará durante unos segundos. La alarma sonará únicamente si se utiliza el amplificador incorporado. 1 Presione (OFF). La unidad se apaga. 2 Presione y, a continuación, extraiga el panel frontal hacia usted. (OFF) Notas No deje caer ni ejerza excesiva presión sobre el panel frontal y la pantalla. No someta el panel frontal al calor ni a temperaturas altas o excesiva humedad. Evite dejarlo en un automóvil estacionado o sobre el tablero o la bandeja trasera. Sugerencia Al transportar el panel frontal, utilice el estuche suministrado. 4

21 Instalación del panel frontal Fije la parte A del panel frontal en la parte B de la unidad, tal como muestra la ilustración, y presione el lado izquierdo hasta que encaje. Expulsión del disco 1 Abra el obturador. x A B Nota No coloque nada sobre la superficie interior del panel frontal. Inserción del disco en la unidad 1 Abra el obturador. 2 Presione el obturador hasta que escuche un clic. x Clic 2 Inserte el disco con la etiqueta orientada hacia arriba. Se inicia la reproducción. 3 Cierre el obturador. El disco se expulsa. Notas No cierre el obturador mientras expulsa o inserta el disco. Es posible que se bloquee y se dañe. Si abre el obturador a la fuerza, es posible que se expulse el disco. Sugerencia El disco puede reproducirse mientras el obturador esté abierto o cerrado. 5

22 Ubicación de los controles y las operaciones básicas Unidad principal ATT OFF OPEN DSPL DIM EQ3 SEEK GP/DISC + REP SHUF BTM SOURCE MODE SEL SENS SCRL LIST CDX-R3410S 9 0 qaqs qd qf qg qh qj qk CDX-R3410 ql Control remoto de tarjeta RM-X w; OFF SOURCE SEL ATT MODE 2 qs qa 3 DSPL + SCRL ws qj wd wa + VOL 6

23 Consulte las páginas indicadas para obtener información detallada. Los botones correspondientes en el control remoto de tarjeta controlan las mismas funciones que los de la unidad. a Botón de volumen +/ Para ajustar el volumen. b Botón ATT (atenuación) Para atenuar el sonido. Para cancelar, vuelva a presionar. c Botón DSPL (pantalla)/dim (atenuador) 4, 8, 10 Para cambiar los elementos de pantalla (presionar); para cambiar el brillo de pantalla (mantener presionado). d OPEN (abrir obturador), ranura del disco (ubicado detrás del obturador) 5 e Pantalla f Botón EQ3 (ecualizador) 9 Para seleccionar un tipo de ecualizador (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM OFF). g Botón OFF Para apagar o detener la fuente. h Botón SEEK +/ Radio: Para sintonizar emisoras en forma automática (presionar); para localizar una emisora en forma manual (mantener presionado). CD: Para omitir pistas (presionar); para omitir pistas en forma continua (presionar y volver a presionar dentro de 1 segundo y mantener); para avanzar o retroceder una pista en forma rápida (mantener presionado). i Botón (extracción del panel frontal) 4 j Botón SOURCE Para encender o cambiar la fuente (Radio/ CD/MD* 1 ). k Botón MODE 8, 11 Para seleccionar la banda de radio (FM/AM) o seleccionar la unidad* 2. l Botón SEL (selección) 4, 9, 10 Para seleccionar elementos. m Botón RESET (ubicado detrás del panel frontal) 4 n Selector de frecuencias (ubicado en la parte inferior de la unidad) Consulte Selector de frecuencias en el manual de instalación o conexiones suministrado. o Botones numéricos Radio: Para recibir las emisoras almacenadas (presionar); para almacenar emisoras (mantener presionado). CD/MD* 1 : (1)/(2): GP* 3 /DISC* 2 /+ Para omitir grupos (presionar); para omitir grupos en forma continua (mantener presionado). (3): REP 8 (4): SHUF 8 p Botón SENS/BTM 8 Para mejorar la recepción en caso de que fuese débil: LOCAL/MONO (presionar); para iniciar la función BTM (mantener presionado). q Botón SCRL 8 Para desplazar el elemento de pantalla. r Botón LIST 9, 12 Para mostrar una lista. s Receptor del control remoto de tarjeta Los botones siguientes del control remoto de tarjeta también presentan botones y funciones distintos que los de la unidad. t Botones < (.)/, (>) Para controlar la radio/cd, el mismo que (SEEK) +/ en la unidad. (Para obtener más detalles sobre otras operaciones, consulte la sección Con el control remoto de tarjeta de cada página.) u Botón VOL +/ Para ajustar el volumen. v Botones M (+)/m ( ) Para controlar el CD, el mismo que (1)/(2) /+ en la unidad. (Para obtener más detalles sobre otras operaciones, consulte la sección Con el control remoto de tarjeta de cada página.) w Botones numéricos Para recibir las emisoras almacenadas (presionar); para almacenar emisoras (mantener presionado). *1 Cuando se conectó un cambiador de MD. *2 Cuando se conectó un cambiador de CD/MD. *3 Cuando se reproduce un disco MP3/ATRAC y no se conectó un cambiador. Si se conectó el cambiador, la operación es diferente, consulte la página 11. Nota Si la unidad está apagada y desaparece la pantalla, no se puede operar con el control remoto de tarjeta salvo que se presione (SOURCE) en la unidad o se inserte un disco para activar la unidad en primer lugar. Sugerencia Si desea obtener información adicional sobre cómo sustituir la pila, consulte Sustitución de la pila de litio del control remoto de tarjeta en la página 14. 7

24 CD Si desea conocer más detalles sobre cuándo conectar a un cambiador de CD/MD, consulte página 11. Elementos de pantalla A B Radio Almacenamiento y recepción de emisoras Precaución Para sintonizar emisoras mientras conduce, utilice la función Memoria de emisoras con mejor sintonía (BTM) para evitar accidentes. A Fuente B Número de pista/tiempo de reproducción transcurrido, Nombre del disco/artista, Número del grupo* 1, Nombre del grupo, Nombre de la pista, Información de texto* 2, Reloj *1 El número del grupo se muestra sólo cuando se cambia el grupo. *2 Cuando se reproduce un MP3, se muestra el indicador ID3 y cuando se reproduce un disco ATRAC, se muestra la información de texto grabada por SonicStage, etc. Para cambiar los elementos de pantalla B, presione (DSPL); para desplazarlos B, presione (SCRL) o ajuste A.SCRL-ON (página 11). Sugerencia Los elementos que se muestran en pantalla variarán en función del tipo de disco y el formato grabado. Si desea conocer más detalles acerca de MP3, consulte la página 13; discos ATRAC, consulte la página 14. Reproducción repetida y aleatoria 1 Durante la reproducción, presione (3) (REP) o (4) (SHUF) varias veces hasta que aparezca el ajuste deseado. Seleccione REP-TRACK REP-GP* SHUF-GP* SHUF-DISC Para reproducir pistas en forma repetida. grupos en forma repetida. grupos en orden aleatorio. discos en orden aleatorio. * Cuando se reproduce un disco MP3/ATRAC. Para regresar al modo de reproducción normal, seleccione REP-OFF o SHUF-OFF. Almacenamiento automático BTM 1 Presione (SOURCE) varias veces hasta que aparezca TUNER. Para cambiar de banda, presione (MODE) varias veces. Puede seleccionar entre FM1, FM2, FM3, AM1 y AM2. 2 Mantenga presionado (BTM) hasta que BTM parpadee. La unidad almacena las emisoras en el orden de frecuencia en los botones numéricos. La unidad emite un pitido al almacenar el ajuste. Almacenamiento manual 1 Mientras recibe la emisora que desea almacenar, mantenga presionado un botón numérico (de (1) a (6)) hasta que aparezca MEM. La indicación de botón numérico aparece en pantalla. Nota Si intenta almacenar otra emisora en el mismo botón numérico, se reemplazará la que estaba almacenada previamente. Recepción de las emisoras almacenadas 1 Seleccione la banda y, a continuación, presione un botón numérico (de (1) a (6)). Con el control remoto de tarjeta Para seleccionar emisoras en memoria, presione M o m. 8

25 Sintonización automática 1 Seleccione la banda y, a continuación, presione (SEEK) +/ para buscar la emisora. La búsqueda se detiene cuando la unidad recibe una emisora. Repita este procedimiento hasta recibir la emisora deseada. Sugerencia Si conoce la frecuencia de la emisora que desea escuchar, mantenga presionado (SEEK) +/ para localizar la frecuencia aproximada y, a continuación, presione (SEEK) +/ varias veces para ajustar la frecuencia deseada con mayor precisión (sintonización manual). Sintonización de una emisora mediante una lista Listado Puede generar una lista de frecuencias o de nombres. Si desea conocer más detalles sobre cómo etiquetar una emisora, consulte la página Seleccione la banda y, a continuación, presione (LIST). Aparece el nombre de la frecuencia o emisora. 2 Presione (LIST) varias veces hasta que aparezca la emisora deseada. Transcurridos 5 segundos, la unidad volverá al modo de recepción normal. 3 Presione (SEEK) +/ para sintonizar la emisora. Con el control remoto de tarjeta En el paso 2, para seleccionar la emisora, presione M o m. Otras funciones Almacenamiento y recepción de emisoras Ajuste de las características del sonido BAL/FAD/SUB Puede ajustar el balance, el equilibrio y el volumen del altavoz potenciador de graves. 1 Presione (SEL) varias veces hasta que aparezca BAL, FAD o SUB. El elemento cambia de la manera siguiente: LOW* 1 t MID* 1 t HI* 1 t BAL (izquierdo-derecho) t FAD (frontalposterior) t SUB (volumen del altavoz potenciador de graves)* 2 *1 Si está activado EQ3 (página 9). *2 Cuando la salida de audio se ajusta en SUB (página 11). ATT se muestra en el valor más bajo y se puede ajustar hasta 20 intervalos. 2 Presione el botón volumen +/ varias veces para ajustar el elemento seleccionado. Después de 3 segundos, se completa el ajuste y la pantalla vuelve al modo de recepción/ reproducción normal. Nota Realice el ajuste a los 3 segundos de seleccionar el elemento. Con el control remoto de tarjeta En el paso 2, para ajustar el elemento deseado, presione <, M,, o m. Ajuste de la curva de ecualizador EQ3 Puede definir y almacenar los ajustes del ecualizador para distintos rangos de tono. 1 Seleccione una fuente y presione (EQ3) repetidamente para seleccionar el tipo EQ3. 2 Presione (SEL) varias veces hasta que aparezca LOW, MID o HI. 3 Presione el botón volumen +/ varias veces para ajustar el elemento seleccionado. continúa en la página siguiente t 9

26 El nivel de volumen puede ajustarse en intervalos de 1 db, entre 10 db y +10 db. Repita los pasos 2 y 3 para ajustar la curva de ecualizador. Para restaurar la curva de ecualizador ajustada en fábrica, mantenga presionado (SEL) antes de que finalice el ajuste. Después de 3 segundos, se completa el ajuste y la pantalla vuelve al modo de recepción/ reproducción normal. Con el control remoto de tarjeta En el paso 3, para ajustar el elemento deseado, presione <, M,, o m. Etiquetado de emisora/ disco Cuando sintoniza una emisora o reproduce un disco en un cambiador de CD con la función CUSTOM FILE, puede etiquetar cada emisora/ disco con un nombre personalizado de hasta 8 caracteres (Memorando de emisoras/memorando del disco). Si etiqueta una emisora/disco, el nombre aparece en la lista (página 9 ó 12). 1 Mientras escucha una emisora o reproduce un disco que desea etiquetar, mantenga presionado (LIST). 2 Presione el botón volumen +/ varias veces hasta que aparezca el carácter deseado. Para mover la indicación digital, presione (SEL). A y B y C... y 0 y 1 y 2... y + y y... y (espacio en blanco) y A Repita esta operación hasta que se ingrese el nombre completo. 3 Mantenga presionado (LIST). Finaliza el etiquetado y la pantalla regresa al modo de reproducción/recepción normal. Para mostrar el nombre, presione (DSPL) durante la sintonización o reproducción. Sugerencias Para corregir o borrar un carácter, sobrescriba o ingrese. El Memorando del disco siempre prevalece sobre cualquier título pregrabado. Puede etiquetar un disco en la unidad si se conectó un cambiador con la función CUSTOM FILE. Se suspende REP-TRACK y toda reproducción aleatoria hasta que finalice el etiquetado. Con el control remoto de tarjeta En el paso 2, presione M o m para seleccionar el carácter. Eliminación del nombre personalizado 1 Seleccione la radio o la unidad donde se haya guardado el nombre personalizado que desea eliminar y mantenga presionado (LIST). 2 Mantenga presionado (DSPL). El nombre guardado parpadeará. 3 Presione repetidamente el botón volumen +/ para seleccionar el nombre que desee eliminar. 4 Mantenga presionado (SEL). El nombre se elimina. Si desea eliminar otros nombres, repita los pasos 3 y 4. 5 Mantenga presionado (LIST). La unidad vuelve al modo de reproducción/ recepción normal. Con el control remoto de tarjeta En el paso 3, para seleccionar el nombre, presione M o m. Definición de los elementos de ajuste SET 1 Mantenga presionado (SEL). Aparecerá la pantalla de ajustes. 2 Presione (SEL) varias veces hasta que aparezca el elemento deseado. 3 Presione el botón de volumen +/ para seleccionar el ajuste (ejemplo ON u OFF ). 4 Mantenga presionado (SEL). El ajuste finaliza y la pantalla regresa al modo de recepción/reproducción normal. Nota Los elementos que se muestran en pantalla variarán en función de la fuente y del ajuste. Con el control remoto de tarjeta En el paso 3, para seleccionar el ajuste, presione < o,. 10