MK-F800 COVER

Size: px
Start display at page:

Download "MK-F800 COVER"

Transcription

1 Operating Instructions 使用說明書 Arahan Pengendalian Food Processor (Household Use) 食物處理器 ( 家庭用 ) Pemproses Makanan (Kegunaan di Rumah) Model No. 型號. No. Model. Thank you for purchasing this Panasonic product. This product is intended for household use only. Please read these instructions carefully in order to use this product correctly and safely. Before using this product please give your special attention to the section "SAFETY PRECAUTIONS" (Page -5). Please keep the Operating Instructions for future use. 感謝您購買 Panasonic 的產品 本產品只限於家庭使用 請仔細閱讀本使用說明書, 以確保正確安全使用本產品 使用本產品前, 請您特別留意 安全注意事項 (-5 頁 ) 請妥善保存本使用說明書, 以備將來用途 Terima kasih kerana membeli produk Panasonic. Produk ini hanya untuk kegunaan di rumah sahaja. Sila baca arahan ini dengan telitinya supaya produk ini dapat digunakan dengan cara yang betul dan selamat. Sebelum mengguna produk ini, sila beri perhatian khas kepada "LANGKAH-LANGKAH KESELAMATAN" (Muka surat 6-65). Sila simpan Arahan Pengendalian ini untuk kegunaan masa depan.

2 TABLE OF CONTENTS Page SAFETY PRECAUTIONS IMPORTANT INFORMATION... 5 PART NAMES SAFETY LOCK... 8 CIRCUIT BREAKER AND TEMPERATURE SENSOR PROTECTION... 8 DISASSEMBLY & ASSEMBLY (i) DISASSEMBLY FROM PACKAGED CONDITION... 9 (ii) KNIFE BLADE KNEADING BLADE WHIPPING BLADE GRATING BLADE... 9 (iii) SLICING BLADES SHREDDING BLADES JULIENNE BLADE... 0 (iv) CITRUS PRESS... 0 (v) SALAD DRAINER... FOOD PROCESSOR (i) KNIFE BLADE Preparation of Ingredients How to Use (ii) SLICING BLADES SHREDDING BLADES JULIENNE BLADE Preparation of Ingredients How to Use (iii) KNEADING BLADE... 7 Preparation of Ingredients How to Use (iv) WHIPPING BLADE...8 Preparation of Ingredients How to Use (v) GRATING BLADE... 9 Preparation of Ingredients How to Use (vi) SALAD DRAINER... 0 Preparation of Ingredients How to Use (vii) CITRUS PRESS... Preparation of Ingredients How to Use BLENDER (i) BLENDER... - Disassembly & Assembly Preparation of Ingredients How to Use DRY MILL (ii) DRY MILL Disassembly & Assembly Preparation of Ingredients How to Use AFTER USE TROUBLESHOOTING SPECIFICATIONS...

3 SAFETY PRECAUTIONS (Make sure to follow these instructions) In order to prevent accidents or injuries to the user, other people and damage to property, please follow the instructions below. The following indication indicates the degree of damage caused by incorrect operation. WARNING CAUTION The symbols are classified and explained as follows. This symbol indicates prohibition. Indicates serious injury or death. Indicates risk of injury or property damage. WARNING This symbol indicates requirement that must be followed. Do not damage the Cord or the Plug. (It may cause electric shock, or fire caused by short circuit.) Do not use the appliance if the Cord or the Plug is damaged or the Plug is loosely connected to the outlet. (It may cause electric shock, or fire caused by short circuit.) a If the Cord is damaged, it must be replaced by the manufacturer, its service center or similarly qualified persons in order to avoid a hazard. Do not plug or unplug the Plug with wet hands. (It may cause electric shock.) Do not exceed outlet voltage or use an alternate current other than that specified on the appliance. (It may cause electric shock or fire.) Make sure the voltage supplied to the appliance is the same as your local supply. Plugging other devices into the same outlet may cause over-heating. Do not immerse the Motor Housing in water or splash it with water. (It may cause electric shock, or fire caused by short circuit.) Do not dismantle, repair or modify the appliance. (It may cause fire, electric shock or injury.) a Please contact your service center for repairing. Do not insert any objects into the vent or the gap. (It may cause electric shock or malfunction.) Especially metal objects such as pins or wires. Do not replace any parts of appliance with non-genuine spare parts. (It may cause injury, electric shock or fire.) Do not try to remove the Lid when the appliance is still operating. (It may cause injury.) Do not use hot water (over 60 C) for cleaning purpose or fire to dry the appliance. (It may cause burning or malfunction.) Do not place hot ingredients (over 60 C) into the Bowl or the Blender Jug. (It may cause injury or malfunction.) Do not operate without the Blender Lid in place correctly for the Blender Jug. (It may cause injury.) Do not put your finger or utensils such as spoon, fork etc. into the Bowl or the Blender Jug during operation. (It may cause injury, electric shock, or fire caused by short circuit.) Do not push the Safety Pin and Safety Lever with any instruments, stick etc. as the appliance might be on. (It may cause injury.) English

4 WARNING This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (It may cause burning, injury or electric shock.) Insert the Plug firmly. (Otherwise it may cause electric shock and fire caused by the heat that may generate around the Plug.) Clean the Plug regularly. (A soiled Plug may cause insufficient insulation due to moisture, and may cause fire.) When abnormal operation or breaking down occurs, discontinue the appliance operation immediately and unplug. (It may cause smoke, fire or electric shock.) e.g. during abnormal operation or breaking down. The Plug and the Cord becomes abnormally hot. The Cord is damaged or there has been a power failure. The Motor Housing is deformed or abnormally hot. a Please unplug the appliance immediately and contact the service centre for advice or a repair. Make sure to hold the Plug when unplugging the Plug, i.e. never pull on the Cord. (Otherwise it may cause electric shock, or fire caused by short circuit.) Be careful if hot liquid is poured into the Bowl or Blender Jug as it can be ejected out of the appliance due to a sudden steaming. (It may cause burning.) CAUTION Do not leave the appliance unattended when it is in operation. (It may cause fire or burns.) When leaving the appliance unattended, turn the power off. Do not use the appliance in the following places: Any uneven surface, on non-heat resistant carpet or table cloth etc. (It may cause fire or injury.) In a location where there is risk of the appliance being splashed with water, or near a heat source. (It may cause electric shock or current leakage.) Do not process more than the maximum capacity marked on each container respectively. Follow the recommended ingredient amount for processing. (It may cause injury.) Do not continue operation for a long time. It is recommended to rest the appliance after a certain operating time. (It may cause burns.) Function Food Processor Blender Dry Mill Operating Time (minutes) Rest Time (minutes) 4 * With exception for the stated "Ingredient Preparations" in this Operating Instructions. Unplug the Plug when the appliance is not in use. (Otherwise it may cause electric shock, or fire caused by current leakage.) 4

5 CAUTION Remove the Bowl, Blender Jug and the Mill Container before lift up the Motor Housing from the table. (It may cause injury.) Switch off the appliance and disconnect it from power supply before changing accessories or approaching parts that are moving during operation. (It may cause injury.) When carrying the appliance, be sure to hold the Motor Housing with both hands. Do not carry it by holding only the Bowl or Blender Jug or Mill Container. (It may cause injury.) If the Blender Cutting Blade gets stuck, switch off the Blender, then unplug. Do not insert your finger into the Blender Jug. Use a rubber spatula to remove the ingredients that are blocking the Blender Cutting Blade. (It may cause injury.) Care should be taken when handling the sharp cutting blades, emptying the Bowl or Blender Jug and cleaning. (e.g. Knife Blade, Slicing Blades and etc.) (It may cause injury.) English IMPORTANT INFORMATION Do not place the appliance in the following places. In a location where the appliance being expose to excessive moisture, temperature or direct sunlight. (It may cause malfunction.) Any high or low temperature location such as fridge, freezer, microwave or oven. (It may cause malfunction or breakage.) Do not process hard ingredients (e.g. hard meat, meat with bones) or viscous material. (It may cause malfunction.) Prohibited Ingredients: Attachments Knife Blade Slicing Blades, Shredding Blades and Julienne Blade Kneading Blade Whipping Blade Grating Blade Salad Drainer Citrus Press Blender Dry Mill Description Hard ingredients, viscous ingredients, e.g. coffee beans, dried soyabeans, frozen food, dried squid, and etc. Ingredients with high hard fiber concentrations, viscous ingredients, ingredients that are too soft, e.g. hard vegetables, frozen food, ham, turmeric, ginger, lettuce, tomato, peach, chocolate and etc. Ingredients not suited for dough making, e.g. meat, vegetables, nuts, sauces, spreads. Any other ingredients aside from egg whites and fresh cream. Viscous ingredients, ingredients with high hard fiber concentrations, ingredients that are too small and thin, e.g. yam, celery, leek, pine nuts, and etc. Large chunky ingredients, ingredients that are soft and fragile, e.g. large carrot or potato chunks, tomato, tofu, pasta, noodle, and etc. Any other ingredients aside from citrus fruits, e.g. apple, kiwi and etc. Hard ingredients, highly sticky ingredients, ingredients with low water content, e.g. turmeric, dried soyabeans, frozen food, meat, fish, boiled potatoes, or just ice cubes, and etc. Hard nuts, dried fruit, ingredients with high hard fiber concentration, moist ingredients, liquids, e.g. various nuts, raisins, meat, vegetables, boiled egg, turmeric, and etc. Before Use: Always operate the appliance on a clean, dry, flat, hard and smooth surface, and clean the Rubber Foot (P.6) before use to ensure that the Rubber Foot suction is at optimum performance. 5

6 PART NAMES Food Processor Working capacity:.5 L. Food Pusher. Feeding Tube. Bowl Lid 4. Knife Blade 5. Grating Blade 6. Kneading Blade 7. Whipping Blade 8. Drainer Cover 9. Salad Drainer 0. Blade Stand. Fine Shredding Blade. Coarse Shredding Blade *The shape of the Plug may vary from illustration. 6. Thin Slicing Blade 4. Thick Slicing Blade 5. Julienne Blade 6. Citrus Cone 7. Citrus Strainer 8. Bowl 9. Drive Shaft 0. Motor Housing. Power Switch. Rubber Foot. Cord 4. *Plug

7 PART NAMES Blender, Dry Mill & Accessories Working capacity: L English. Blender Lid. Blender Jug. Blender Cutting Blade 4. Mill Container 5. Mill Cutting Blade 6. Mill Container Base 7. Storage Case Unit 8. Brush Control Panel Mode Selection - Auto Menu - Mince Mode Chop Mode Frozen Mode Paste Mode Drainer Mode - Manual Menu - Continuous Mode Intermittent Mode PULSE Switch Mode Indication L.E.D. Stop/Start Switch For Auto Menu: to Pause/Start process For Manual Menu: to Stop/Start process Rotary Dial Adjust Speed and Timer/Driving Time Speed and Timer/Driving Time indication L.E.D. : Light up when Manual Menu is operating and indicate speed level by bars. : Light up when Auto menu is pressing and indicate Timer/Driving time by bars. Note: The program will time-out and reset itself after 0 seconds if no further action is done after a function is selected. Turning the Rotary Dial clockwise will increase the number of lighted bars and vice versa. The default speed for the Continuous and Intermittent modes are at maximum, (level 0). The program will time-out and reset itself after 0 seconds if the program is paused during processing and no further action is done. Continuous Mode will stop automatically approximately 9 minutes and Intermittent Mode will stop automatically approximately 7 minutes after processing is started. 7

8 SAFETY LOCK The Safety Pin is designed to prevent the appliance from switching on when - The Bowl Lid or Citrus Strainer and the Bowl are not fully locked to each other. - The Bowl, Blender Jug or Dry Mill are not fully locked to the Motor Housing. The Safety Lever only activates the Safety Pin if the Bowl Lid or Citrus Strainer is secured on the Bowl. Position A : Unlock Position B : Lock Safety Pins B A Fully locking steps : For Bowl and Blender Jug, align the triangle mark with the Motor Housing as shown in position A. Turn it clockwise until a 'click' sound is heard and the triangular mark now aligns to position B. For Dry Mill, place onto Motor Housing and turn clockwise until a 'click' sound is heard. To unlock, follow the locking steps in reverse. Note: Do not push the Safety Pin and Safety Lever with any instrument, stick etc. Do not pour liquids or ingredient at the Safety Pin and Safety Lever area. Keep the Safety Pin and Safety Lever area clean to avoid foreign particles accumulate on the area. Actions above will ensure the Safety Pin and Safety Lever function properly. If not followed, it will damage the parts related to the Safety Pin and Safety Lever. CIRCUIT BREAKER AND TEMPERATURE SENSOR PROTECTION This appliance has the Circuit Breaker and Temperature Sensor functions to stop the motor when motor is overloaded. (refer to page 0) 8

9 FOOD PROCESSOR -DISASSEMBLY & ASSEMBLY- Disassembly from Packaged Condition English Top of the Knife Blade Rotate the Bowl Lid anticlockwise and lift up from the Bowl. Hold the top of the Knife Blade and lift up to remove from Bowl. Note: Beware of the sharp edges of the Knife Blade when removing it from the Bowl. Assembly of Food Processor Attachments It is highly recommended to clean all attachments and accessories and dry well before using the appliance for the first time, refer to page 6 and 7 for the cleaning method. Unplug when assembling the unit. Before plugging in, ensure that the Power Switch is switched off. Please refer to page 7 under 'Storing' on how to re-position the Motor Housing. Knife Blade Kneading Blade Whipping Blade Grating Blade or 4 or or Place the Knife Blade (Kneading Blade or Whipping Blade or Grating Blade) into the Bowl. Note: For the Knife Blade, ensure that the Drive Shaft is protruding from the Knife Blade after insertion. Put the ingredients into the Bowl. Note: For the Grating Blade, place the ingredients on top of the blade and spread them out evenly. Place the Bowl Lid on top of the Bowl and turn it clockwise until a 'click' sound is heard. Insert the Food Pusher into the Feeding Tube. 9

10 FOOD PROCESSOR -DISASSEMBLY & ASSEMBLY- Assembly of Food Processor Attachments Slicing Blades (Thick / Thin) Shredding Blades (Coarse / Fine) Julienne Blade Finger Holes Projected Detent Fit the projected detent of the desired blade onto the Blade Stand and ensure it is seated properly. Push down on the dimple on the blade as seen above until a 'snap' sound is heard. Note: Beware of the sharp edges on the blades while inserting into the Blade Stand. To remove the blade, turn over the Blade Stand and push down on the reverse side of the dimple on the blade. 4 Insert finger and thumb into the finger holes to grip the Blade Stand. Place the assembled Blade Stand into the Bowl. Note: Ensure that the Drive Shaft is protruding from the Blade Stand after insertion. Place the Bowl Lid on top of the Bowl and turn it clockwise until a 'click' sound is heard. Citrus Press Place the Citrus Strainer onto the Bowl. Turn it clockwise until a 'click' sound is heard. Attach the Citrus Cone onto the Drive Shaft. 0

11 PP FOOD PROCESSOR -DISASSEMBLY & ASSEMBLY- Assembly of Food Processor Attachments Salad Drainer English A PP B Place the Salad Drainer into the Bowl. Insert the ingredients into the Salad Drainer. Place Drainer Cover on top of the Salad Drainer until the mark aligns as shown in A. Turn the Drainer Cover anticlockwise until the mark aligns as shown in B. 4 Ensure that the Drive Shaft is protruding out of the Salad Drainer after insertion. Place the Bowl Lid on top of the Bowl and turn it clockwise until a 'click' sound is heard. Attaching the assembled units to the Motor Housing. Place the Bowl on top of the Motor Housing until the mark aligns as shown in A.. Turn the Bowl clockwise until a 'click' sound is heard. Ensure that the triangle mark on the Bowl is aligned with the rectangle mark on the Motor Housing as seen in B. B A To disassemble, follow the assembly steps in reverse.

12 FOOD PROCESSOR -KNIFE BLADE- Ingredient Preparations Function Ingredient Mode Quantity Operating Time (approx.) Preparation Method Mince Meat Fish Auto 50 ~ 400 g 5 ~ 40 sec Initial setting is for 00 g (0 sec) 50 ~ 500 g ~ 0 sec Remove all skin, bones, and tendons, cut into ~ cm cubes. Onion Auto 50 ~ 500 g 0 ~ 50 sec Initial setting is for 00 g (0 sec) Peel skin, cut into ~ cm cubes. Garlic 5 ~ 500 g 0 ~ 0 sec Peel skin. Chop Carrot Italian Parsley Continuous Speed: Max 50 ~ 450 g 5 ~ 70 g 0 ~ 0 sec 0 ~ 40 sec Peel skin, cut into ~ cm cubes. Remove stalk. Mushroom 0 ~ 50 g ~ 5 sec Cut into ~ cm cubes. Crush Parmesan Cheese Continuous Speed: Max 0 ~ 00 g 0 ~ 60 sec Cut into ~ cm cubes. Mash Frozen Boiled Potato Frozen Banana Intermittent Speed: Max Auto 00 ~ 400 g 50 ~ 450 g 0 ~ 40 sec 40 ~ 0 sec Initial setting is for 50 g (60 sec) Cut into ~ cm cubes. Do not over process. ~ cm width, half frozen condition, i.e. toothpick can pierce. Ice Crush Ice Cubes Continuous Speed: Max ~ 0 pcs ~ 0 sec ~ cm ice cubes. Grind Peanuts Continuous Speed: Max 0 ~ 00 g 5 ~ 0 sec Remove peanut shell and skin. Paste Roasted Peanuts Auto 00 ~ 400 g 4 ~ 0 min Initial setting is for 00 g (7 min) Remove peanut shell and skin. Crumb Soft White Bread Continuous Speed: Max 0 ~ 00 g 5 ~ 60 sec Slice soft bread into 6 to 8 pieces. Knead (for confectionary) Juice Make Flour Fruit, Liquid etc. Continuous Speed: Max Continuous Speed: Max ~ 00 g ~,500 ml ~ 0 sec ~ 0 sec Use for making confectionery such as sweets and cakes. Cut into ~ cm cubes. Process solids first. Fill liquid till total not exceeding,500 ml. Do not add more than 0 pcs of ice cubes during processing. Soup Make Boiled Vegetable, Liquid etc. Continuous Speed: Max ~,500 ml ~ 0 sec Cut into ~ cm cubes. Process solids first. Fill liquid till total not exceeding,500 ml.

13 FOOD PROCESSOR -KNIFE BLADE- Operating with Auto Menu English After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the required Auto Menu mode (except the Drainer Mode). The selected Mode Indication L.E.D. will light up and a beep sound will be heard. The Driving Time and Stop/Start Switch Indication L.E.D. will light up and blink. 4 Each Auto Menu has a pre-programmed driving time. Each lighted bar represents 0 seconds* of driving time. Push the Stop/Start Switch to start the operation. During operation, the Driving Time L.E.D. will turn off one by one after every 0 second intervals until the set duration is completed and 4 beep sounds will be heard. The Mode Indication L.E.D.s will light up and blink. 5 6 After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Knife Blade from the Bowl before removing the processed ingredients. *For Paste Auto Menu, each lighted bar represents minute. The lighted bar will decrease at every minute interval. Note: Always ensure that the Knife Blade is inserted before adding ingredients into the Bowl. The Driving Time of the Auto Menu can be increased or decreased by adjusting the Rotary Dial if necessary. The operation of the Auto Menu can be stopped prematurely by pushing the Stop/Start Switch before the set duration ends. Depending on the speed and amount of ingredients used, there will be significant vibrations present. In that case, hold down the Bowl Lid with both hands to support it during its operation.

14 FOOD PROCESSOR -KNIFE BLADE- Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. 4 Select the Continuous or Intermittent mode. The selected Mode Indication L.E.D. will light up and a beep sound will be heard. The Speed, Stop/Start Switch and PULSE Switch Indication L.E.D. will light up and blink. Adjust the desired speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start or PULSE Switch to start the operation. 5 6 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. The speed can be adjusted during operation. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Knife Blade from the Bowl before removing the processed ingredients. 4 Note: Always ensure that the Knife Blade is inserted before adding ingredients into the Bowl. Do not exceed the stated amount of ingredients for kneading as abnormal vibration may occur. Do not insert hot ingredients into the Bowl for processing. Always ensure that the ingredients are sufficiently cooled before inserting, e.g. boiled potato. For Juice Make, fill in the solid ingredients first into the Bowl, followed by the liquid ingredients until the total volume does not exceed,500 ml. Depending on the speed and amount of ingredients used, there will be significant vibrations present. In that case, hold down on the Bowl Lid to support it during its operation. For kneading, do not reprocess after the dough has formed the first time. When process the liquid ingredients together with ice cubes, put the ice cubes not more than 0 pcs (approx. 70 g).

15 FOOD PROCESSOR -SLICING BLADES SHREDDING BLADES JULIENNE BLADE- English Slicing Blades (Thick / Thin) - used for slicing ingredients Shredding Blades (Coarse / Fine) - used for shredding and grating ingredients. Julienne Blade - used for making french fries and shredding ingredients. Ingredient Preparations for Slicing Blades (Thick / Thin) Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Cucumber 700 g Onion 700 g Slice Carrot Continuous 600 g - Speed: Max Cut ingredient till it is small enough to fit into the Feeding Tube. Potato 600 g Cabbage 400 g Ingredient Preparations for Shredding Blades (Coarse / Fine) Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Cucumber 500 g Shred Carrot Potato Continuous Speed: Max 500 g 650 g - Cut ingredient till it is small enough to fit into the Feeding Tube. Cheese 500 g Cut ingredient till it is small enough to fit into the Feeding Tube. Do not use hard ingredients such as Parmesan. Ingredient Preparations for Julienne Blade Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use French Fry Shred Potato Cabbage Continuous Speed: Max 800 g 500 g - Cut ingredient till it is small enough to fit into the Feeding Tube. 5

16 FOOD PROCESSOR -SLICING BLADES SHREDDING BLADES JULIENNE BLADE- Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode. The selected Mode Indication L.E.D. will light up and a beep sound will be heard. The Speed, Stop/Start and PULSE Switch Indication L.E.D. will light up and blink. 4 Adjust the speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch or PULSE Switch to start the operation. 5 Insert the ingredients into the Feeding Tube and push down with the Food Pusher. 6 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Blade Stand from the Bowl before removing the processed ingredients. 6 Note: When using long and narrow ingredients, place it against the front wall of the Feeding Tube as indicated in Figure, for support while in operation to avoid uneven processing. Dispose of any remaining lumps of unprocessed ingredients. Align high fibre ingredients as indicated in Figure for a consistent processing result. Front Wall Figure Figure

17 FOOD PROCESSOR -KNEADING BLADE- Ingredient Preparations for Kneading Blade Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Knead (for bread) Bread Flour Liquid Continuous Speed: Start with level, increase every second till Max. 00 g 60 ~ 00 ml ~ 0 sec Mix yeast with water and add during the processing of dough (adding yeast directly before processing may result in flaking and premature rising). If dough mix still appears flaky after initial processing, add tsp of water into the mix. When large vibrations occur due to dough mix wrapping around the Drive Shaft, add tbsp of flour. Do not reprocess the dough after the process is complete, if the dough is not satisfactory, knead by hand. English Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust to the appropriate speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch to start the operation. 4 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Observe the formation of the dough ball. Push the Stop/Start Switch to stop the driving operation once a firm dough ball is formed. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the dough ball from the Bowl before removing the Kneading Blade. Note: Do not exceed the stated amount of ingredients for the Kneading Blade as abnormal vibration may occur. Depending on the speed and amount of ingredients used, there will be significant vibrations present. In that case, hold down the Bowl Lid with both hands to support it during its operation. For kneading, do not reprocess after the dough has formed the first time. High amounts of butter and sugar in the dough may cause abnormal vibration when using the Kneading Blade. Using flour other than bread flour may cause abnormal vibration. Before processing, remove ~ tbsp of water from the total amount stated and add the water little by little during processing if necessary. 7

18 FOOD PROCESSOR -WHIPPING BLADE- Ingredient Preparations for Whipping Blade Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Whip Egg White Cream Continuous Speed: Max ~ 6 pcs 00 ~ 00 ml 50 ~ 90 sec 5 sec ~ min Separate the egg white from the yolk for a smooth meringue. Use fresh cream of fat content 5% or higher at 5 C. Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust the speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch to start the operation. 4 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Observe the rising and formation of the whipped ingredients. Push the Stop/Start Switch to stop the driving operation once a desired texture is formed. After the processing is completed, switch off the Power Switch and unplug from the socket. Carefully remove the Whipping Blade together with the processed ingredients from the Bowl. Note: Do not over process the whipping cream, it may break down to form clumps of butter. Using different brands of whipping cream will have varying results. It is recommended to process until the cream is sufficiently whipped. 8

19 FOOD PROCESSOR -GRATING BLADE- Ingredient Preparations for Grating Blade Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use English Carrot 00 g Grate Apple Continuous Speed: Max 00 g - Cut into ~ cm cubes. Cucumber 00 g Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust the speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch to start the operation. 4 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Grating Blade from the Bowl before removing the ingredients. Note: Do not insert the ingredients through the Feeding Tube during operation of the Grating Blade. 9

20 FOOD PROCESSOR -SALAD DRAINER- Ingredient Preparations for Salad Drainer Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Drainer Lettuce Leaves Cabbage Auto 00 g 00 g 0 ~ 60 sec Initial setting is for 50 g (0 sec) 0 ~ 70 sec Cut into ~ 5 cm slices. Shredded into ~ mm. Operating with Auto Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Drainer mode. The selected Mode Indication L.E.D. will light up and a beep sound will be heard. The Driving Time and Stop/Start Switch Indication L.E.D. will light up and blink. 4 Each Auto Menu has a pre-programmed driving time. Each lighted bar represents 0 seconds of driving time. Push the Stop/Start Switch to start the operation.during operation, the Driving Time L.E.D. will turn off one by one after every 0 second intervals until the set duration is completed and 4 beep sounds will be heard. The Mode Indication L.E.D.s will light up and blink. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Salad Drainer from the Bowl. 0 Note: Maximum working capacity of the Salad Drainer: 00 g or till maximum height of Salad Drainer, whichever comes first. Prohibited ingredients: refer to page 5. Ensure that the ingredients are spread evenly around the Salad Drainer before processing. Do not operate the Salad Drainer in any other mode except Drainer mode. Always ensure that the Drainer Cover is attached onto the Salad Drainer before operation, otherwise the ingredients might come out and tear around the Bowl. Depending on the amount of ingredients used, there will be significant vibrations present. In that case, hold down the Bowl Lid with both hands to support it during its operation.

21 FOOD PROCESSOR -CITRUS PRESS- Ingredient Preparations for Citrus Press Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use English Squeeze Citrus Fruit Continuous Speed: Level 4,000 ml - Cut fruit into halves. Operating with Manual Menu After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust to level 4 with the Rotary Dial. Push the Stop/Start Switch to start the operation Place the half cut fruit with the cut side on top of the Citrus Cone and press down firmly to extract juice. During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Citrus Press attachment from the Bowl before pouring the extracted juice out. Note: Always ensure that the Citrus Cone is placed onto the Citrus Strainer before usage. Stop the processing periodically to remove the pulp remaining on the Citrus Strainer to ease the juice extraction process. It is not recommended to operate the Citrus Press at speed levels higher than level 4. Avoid touching the Citrus Cone while it is turning.

22 BLENDER Assembly and Disassembly of Blender Attachment B A Insert ingredients into the Blender Jug and close with the Blender Lid. Place the Blender Jug on top of the Motor Housing until the mark aligns as shown in A. To disassemble, simply follow the assembly steps in reverse. Turn the Blender Jug clockwise until a 'click' sound is heard. Ensure that the triangle mark on the Blender Jug is aligned with the rectangle mark on the Motor Housing as seen in B. Ingredient Preparations for Blender Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Liquidize Fruit, Vegetable Continuous Speed: Max,000 ml ~ min Cut into cm cubes. Note: Maximum working capacity: L. Prohibited ingredients for Blender Jug: refer to page 5. It is not recommended to blend hard and viscous ingredients. However, if necessary, cut the hard ingredients into small pieces (eg. cut carrot into cm³ cubes) and fill the Blender Jug with the ingredients not exceeding half its rated capacity. Do not fill exceeding the maximum level and reduce ingredients when appliance makes abnormal sound or vibration during operation. Add in soft ingredients (fruits, vegetables) into the Blender Jug before adding in other ingredients.

23 BLENDER Operating with Manual Menu English After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust the speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch to start the operation. 4 4 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Blender Unit from the Motor Housing and proceed to remove the ingredients. Note: If the Cutting Blade gets stuck, switch off immediately and unplug. Do not attempt to proceed to unstuck the ingredients with your fingers, use an object like a rubber spatula instead. During blending, there is a possibility that the ingredients will splash out of the Blender Lid hole. In the event that it splashes out, wipe it off with a dry cloth. Do not operate exceeding the rated operation duration ( min ON, min OFF).

24 DRY MILL Disassembly from Packaged Condition Maximum Level Maximum Level for Dry Ingredients Turn the Mill Container Base anticlockwise to unlock and lift up from the Mill Container. A maximum level for dry ingredients is indicated on the Mill Container. Do not fill exceeding this level. Assembly and Disassembly of Dry Mill Attachment Turn the Mill Container upside down and fill in the ingredients without exceeding the maximum level indicated. Place the Dry Mill Unit on top of the Motor Housing. Turn the Dry Mill Unit clockwise until a 'click' sound is heard. Place the Mill Container Base into the Mill Container and turn it clockwise until a 'click' sound is heard. Make sure the ribs on outer surface of the Mill Container Base and inner surface of the Mill Container are hooked firmly. To disassemble, simply follow the assembly steps in reverse. Ingredient Preparations for Dry Mill Function Ingredient Mode Max Operating Time (approx.) Preparation Method Single Use Grind Coffee Bean Pepper Continuous Speed: Max Till Max Level ~ 60 sec - Note: Prohibited ingredients: refer to page 5. Do not operate the unit with empty Dry Mill. Do not fill exceeding the maximum level and reduce ingredients when the appliance makes an abnormal sound or vibrates during operation. 4

25 DRY MILL Operating with Manual Menu English After completing the assembly steps, plug-in the plug into the socket and turn on the Power Switch. The Mode Indication L.E.D.s will light up and blink. Select the Continuous mode and adjust the speed with the Rotary Dial. The more bars are lighted, the higher the speed. Push the Stop/Start Switch to start the operation. 4 4 During the driving operation, the Stop/Start Indication L.E.D. will remain lit. Push the Stop/Start Switch to stop the driving operation. After the processing is completed, switch off the Power Switch and unplug from the socket. Remove the Dry Mill Unit from the Motor Housing and proceed to remove the ingredients. Note: While removing the ingredients, be careful of the Cutting Blade. Do not operate exceeding the rated operation duration ( min ON, min OFF). 5

26 AFTER USE Cleaning Pre-wash The pre-wash enables easier cleaning. It can be used for the Knife Blade and Blender Unit. To pre-wash, simply follow the steps below. Food Processor Blender Put the used attachment inside the Bowl, fill the Bowl with water until the attachment is submerged in water (max. 500 ml). Place the Bowl Lid on top of the Bowl and turn it clockwise until a 'click' sound is heard. For the Blender Unit, fill 500 ml of water into the Blender Jug and cover with the Blender Lid. Plug-in the plug into the socket and turn on the Power Switch. Food Processor: Select the Intermittent mode, push the Stop/Start Switch and operate for 0 ~ 0 seconds at level 0. Blender: Select the Continuous mode, push the Stop/ Start Switch and operate for 0 ~ 0 seconds at level 0. Push the Stop/Start Switch to stop the driving operation. Switch off the Power Switch and unplug from the socket. Remove the attachments and proceed for cleaning. Wash these items by rinsing them under running water. Use neutral kitchen detergent if necessary. Proceed to wipe them dry with a clean cloth. Wash these items by rinsing them under running water, and clean carefully with Brush. Use neutral kitchen detergent if necessary. Note: These items are extremely sharp and should be handled with extra care while cleaning. Avoid hitting these items on hard objects during the cleaning process. The Mill Container Base must not be washed, use Brush to clean. 6

27 AFTER USE Motor Housing / Rubber Foot Wipe off any dirt or stains with a clean damp cloth. Note: Ensure that the power cord is unplugged before cleaning the Motor Housing. Do not wash the Motor Housing under running water. Never use corrosive liquids (e.g. alcohol, thinner, etc) to clean the Motor Housing. English Cleaning with a Dishwasher The Bowl and Bowl Lid of this appliance are dishwasher safe. Note: Do not place these items near the dishwasher heater area as high temperatures may damage the parts. Storing Ensure all attachments and the Bowl are removed from the Motor Housing prior to storage. Release Lever To release the Rubber Foot suction of the Motor Housing, press on the release lever located at the bottom side of the Motor Housing at the same time as seen in the above picture and lift up. Tilt the Motor Housing on its side, and proceed to wind up the Power Cord around the Cord Winding Area partially, leaving the Plug at the sides. (i) (ii) (iii) (i) Store the Knife Blade inside the Bowl. The Storage Case Unit is included to store the other attachments. Store the attachments in place as per packaging condition. (ii) List of attachments in Storage Case Unit: Kneading Blade, Citrus Cone, Thick Slicing Blade, Thin Slicing Blade, Fine Shredding Blade, Coarse Shredding Blade, Julienne Blade, Blade Stand, Grating Blade, Whipping Blade and Brush. (iii) Place the Storage Case Lid beneath the Storage Case to collect the drained water from the washed attachments. Note: Dispose of the flexible plastic cover after opening the Storage Case. 7

28 TROUBLESHOOTING Please check the following points before arranging for service. Problem Cause and Action The appliance does not turn on. w The plug is loose in the outlet. Æ Plug in firmly into the outlet. The Power Switch has not been switched on. Æ Turn on the Power Switch. None of the Control Panel Functions can be selected. w Gloves may cause insensitivity of the Control Panel. Æ Select the functions with bare fingers. Pressing the function at the wrong position. Æ Press firmly on the illustration on the Control Panel. The appliance is already operating. Æ The functions cannot be changed when the appliance is operating. Stop the previous function before selecting a new one. The appliance does not start even the Stop/Start Switch is pressed. (Error Mode is indicated) w The Bowl, Blender Unit or Dry Mill Unit is not properly locked onto the Motor Housing. Æ Ensure that the triangle mark on the attachments are aligned with the rectangular mark on the Motor Housing as seen in page 8. The Bowl Lid or Citrus Strainer is not fully locked onto the Bowl. Æ Fully secure the Bowl Lid or Citrus Strainer onto the Bowl. The appliance does not operate even when the function is started. (No Error Mode) The selected function is canceled. (The Mode Indication L.E.D. starts blinking). w w The ingredients are jammed. Æ Remove the ingredients carefully and ensure that the amount used is as stated. The appliance was left idle for more than 0 seconds after selecting the function. Æ Ensure that action is done after selecting the function within 0 seconds. The appliance suddenly stops during operation. w The circuit breaker protection is activated. (Refer to page 8) Too much ingredients were inserted. Æ Remove the excess ingredients and ensure that the amount used is as stated. Large chunks or hard ingredients were used. Æ Ensure that the ingredients are cut into the stated sizes. Do not use hard ingredients such as frozen foods or highly dense solids. The safety lock was triggered. (Refer to page 8) Abnormal vibration during operation may offset the safety lock engagement. Æ Ensure that the ingredients used and the amount are as stated. Æ Lock the Bowl Lid or Citrus Strainer onto the Bowl firmly, and ensure that the Bowl, Blender Unit, or Dry Mill Unit is locked firmly onto the Motor Housing. 8

29 TROUBLESHOOTING Problem Cause and Action There is abnormal vibration and noise during operation. w The Rubber Feet and/or the work top are not clean. Æ Wipe off any dirt or stains with a clean damp cloth. The Rubber Foot is only effective when placed on a clean, smooth and flat surface. The ingredients used for processing is either too much or too hard. Æ Ensure that the ingredients used are as stated, reduce the ingredients if it is over the stated amount. English The texture and consistency of the processed ingredients did not turn out well. w Some ingredients might be too difficult to process raw, e.g.pumpkin. Æ Precook might be necessary to soften the ingredients before processing, i.e. until a fork can easily pierce. Ingredient size is not according to the preparation method. Æ Prepare accordingly to follow the size stated. Processing certain ingredients at the same time may result in lumps remaining for Frozen mode. Auto Menu The Auto Menu's default processing duration is meant for the stated ingredient amounts. Any other ingredient amounts processed will affect the performance. Æ Increase the processing duration by adjusting the Rotary Dial and process till the desired texture and consistency. Manual Menu The maximum ingredient amount and processing duration are meant to serve as a guideline, lesser ingredient amount and different ingredients will affect the performance. Æ Process the ingredients with a suitable duration till the desired texture and consistency. 9

30 Error Mode Indication Circuit Breaker Protection, High Voltage Detection and High Current Detection i) Circuit Breaker Protection ii) High Voltage Detection iii) High Current Detection No L.E.D.s light up. Alternate blinking of Chop and Intermittent L.E.D.s. Alternate blinking of Mince+Chop and Continuous+Intermittent L.E.D.s. Action: For scenario i) and iii), turn off the Power Switch at the side of Motor Housing, reduce the amount of ingredients into half and resume operation. If it still does not start, turn off the Power Switch again at the side of Motor Housing and resume operation. For scenario ii), the Error Mode Indication is shown due to exceed voltage rating. Use 0-40 V. Motor Overheat The Bowl, Blender Unit or Dry Mill Unit is not properly locked onto the Motor Housing. Alternate blinking of Mince and Intermittent L.E.D.s. Action: Turn off the Power Switch, and let the appliance to cool down (approx. 0 min). Reduce the amount of ingredients into half and resume operation. Alternate blinking of Mince+Chop+Frozen and Paste+Drainer+Continuous L.E.D.s. Action: Reattach the part onto the Motor Housing in proper position (Refer to page 8). Electronic component malfunction or or Alternate blinking of Mince or Chop or Frozen and Continuous L.E.D.s. Action: Please contact your nearest service center for repairing. 0

31 SPECIFICATIONS Model No. Function Power Supply Rated Consumption Switch Operation Rating Dimension (Approx.)(HxWxD) Mass (Approx.) Capacity (Approx.) Attachment & Accessories Common Accessories Dishwasher Safe Items Food Processor minutes ON, 4 minutes OFF 45 x 64 x 65 mm 4. kg Container Capacity:.5 L Maximum working capacity: Liquids only =.5 L Solids only = 600 g Knife Blade, Grating Blade, Kneading Blade, Whipping Blade, Salad Drainer, Blade Stand, Shredding Blades (Coarse & Fine), Slicing Blades (Thick & Thin), Julienne Blade, Citrus Press and Storage Case Unit MK-F V ~ Hz W Rotary Dial with Soft Touch Panel Switch Blender & Dry Mill Blender: minutes ON, minutes OFF Dry Mill: minute ON, minutes OFF With exception for the stated on "Ingredient Preparations" page. Brush with Spatula Bowl and Bowl Lid Blender : 406 x 64 x 65 mm Dry Mill : 98 x 64 x 65 mm Blender : 4.0 kg Dry Mill :.8 kg Blender : L Dry Mill : 50 g (Coffee Beans) With exception for the stated on "Ingredient Preparations" page. Blender Unit, Dry Mill Unit English

32 目录 頁安全注意事項 重要信息... 5 零件名稱 安全鎖... 8 電路自動斷路器及溫度感應保護... 8 拆卸與組裝方法 (i) 從包裝狀態下拆卸... 9 (ii) 切刀 麵團刀片 攪拌刀片 切絲刀片... 9 (iii) 切片刀 磨碎刀片 薯條製作刀片 (iv) 壓榨器 (v) 沙律漏斗... 4 食物處理器 (i) 切刀 材料準備工作 使用方法 (ii) 切片刀 磨碎刀片 薯條製作刀片 材料準備工作 使用方法 (iii) 麵團刀片 材料準備工作 使用方法 (iv) 攪拌刀片 材料準備工作 使用方法 (v) 切絲刀片 材料準備工作 使用方法 (vi) 沙律漏斗 材料準備工作 使用方法 (vii) 壓榨器... 5 材料準備工作 使用方法 攪拌機 (i) 攪拌機 拆卸與組裝方法 材料準備工作 使用方法 乾碾磨機 (ii) 乾碾磨機 拆卸與組裝方法 材料準備工作 使用方法 使用後 故障排除 規格... 6

33 安全注意事項 ( 請務必按照指示操作 ) 為了避免使用者或其他人員發生意外, 或人身傷害和財產損失, 請遵循以下的使用說明 因錯誤操作所造成的危害和損害程度, 如下區分說明 警告 圖標的區分和解釋如下 可能會導致嚴重的人身傷害或死亡 注意 可能會導致人身傷害或財產損失的風險 此圖標表示禁止 警告 此圖標表示務必遵循的措施 請勿損壞電源線或插頭 ( 這可能會因短路導致觸電或火災 ) 如果電源線或插頭損壞, 或插在電源插座的插頭出現鬆動, 請勿使用本產品 ( 這可能會因短路導致觸電或火災 ) a 如果電源線損壞, 必須由生產商 其服務中心或具同等資格的人更換, 以免發生危險 請勿用沾水的手插入或拔除插頭 ( 這可能會導致觸電 ) 請勿使用超過指定的電源供應插座, 也不要使用本產品所指定以外的其他電壓 ( 這可能會導致觸電或火災 ) 請確保本產品所標示的電源供應和您使用的電源供應一致 若與其他電器合用同一插座, 可能會因電流超額, 導致電線過熱 請勿將馬達機座浸入水中或對其噴水 ( 這可能會因短路導致觸電或火災 ) 請勿自行拆開 修理或改裝本產品 ( 這可能會導致火災 觸電或人身傷害 ) a 請聯絡服務中心進行維修 請勿將任何異物插入排氣口或空隙處 ( 這可能會導致觸電或機能故障 ) 尤其是金屬物體, 如針或鐵線 請勿用其他零件代替本產品的原裝零件 ( 這可能會導致人身傷害 觸電或火災 ) 本產品正在運轉時, 請切勿打開蓋罩 ( 這可能會導致人身傷害 ) 請勿使用熱水 ( 超過 60 度 ) 進行清洗或使用火烘乾本產品 ( 這可能會導致燒傷或機能故障 ) 請勿將 60 度以上的材料置入容器或攪拌機容器內 ( 這可能會導人身傷害或機能故障 ) 請勿在攪拌機蓋罩沒完整裝置於攪拌機容器的情況下啓動 ( 這可能會導致人身傷害 ) 啟動時, 請勿將手指或餐具如茶匙 叉子等放入容器或攪拌機容器內 ( 這可能會導致人身傷害 因短路導致觸電或火災 ) 請勿用任何工具, 棒狀物等來按壓安全銷和安全杆, 因為產品可能會啓動 ( 這可能會導致人身傷害 ) 中文 本產品不適合身體 感官思維有缺陷者, 或缺乏經驗與知識者使用 ( 包括兒童 ) 除非他們的安全監護人给予他們關於產品的適當使用和監督與指示 必需監督兒童以確保他們不會將產品當成玩具 ( 這可能會導致燒傷 人身傷害或觸電 )

34 警告 穩固插入電源插頭 ( 否則可能會因插頭周圍產生的熱量導致觸電和火災 ) 定期清潔插頭上的灰塵 ( 灰塵聚積過多的插頭, 會因受潮濕等導致絕緣不良而可能引起火災 ) 出現異常或故障時, 請立即停止使用本產品, 並拔掉插頭 ( 否則, 可能會導致冒煙 火災或觸電 ) 異常或故障示例 : 插頭和電源線異常發熱 電源線損壞或不能通電 馬達機座變形或異常發熱 a 請立即拔出插頭, 並交由服務中心進行檢查或維修 當拔下插頭時, 務必握住插頭將它拔下, 切勿拉扯電源線 ( 否則可能會因短路導致觸電或火災 ) 注入熱液體時請小心處理, 因為蒸氣有機會突然噴出 ( 這可能會導致燒傷 ) 注意 請勿讓本產品在無人看管下操作 ( 這可能會引起火災或燒傷 ) 離開時, 請切斷電源 請勿在以下的地方使用本產品 不平穩的表面 不耐熱的地毯或桌布等 ( 這可能會引起火災或人身傷害 ) 可能會濺到水或靠近熱源的地方 ( 這可能會導致觸電或漏電 ) 請勿處理超過各容器的最大容量 請遵循所建議的材料份量進行處理 ( 這可能會導致人身傷害 ) 請勿長時間持續不間斷操作 建議在一定的操作時間後, 讓本產品休息 ( 這可能會導致燒傷 ) 功能食物處理器攪拌機乾碾磨機 操作時間 ( 分鐘 ) 休息時間 ( 分鐘 ) 4 * 除了本使用說明書所規定的 材料準備工作 不使用本產品時, 請從電源插座上拔下插頭 ( 否則可能會因漏電導致觸電或火災 ) 4

35 注意 在把馬達機座從桌上抬起前, 請把容器 攪拌機容器及碾磨機容器移走 ( 這可能會導致人身傷害 ) 更換零件或接觸正在操作的零件前, 請關機並切斷電源 ( 這可能會導致人身傷害 ) 搬動本產品時, 確保用雙手握緊馬達機座 請勿只握緊容器或攪拌機容器或碾磨機容器來搬動本產品 ( 這可能會導致人身傷害 ) 如果攪拌機切削刀卡住, 應立即關閉電源並拔下插頭 請勿試圖將手指伸進攪拌機容器內 請使用橡皮刮刀取出阻礙攪拌機切削刀的材料 ( 這可能會導致人身傷害 ) 處理鋒利的刀 清空容器與攪拌機容器和清潔時請小心處理 ( 例如切刀 切片刀等 ) ( 這可能會導致人身傷害 ) 中文 重要信息 請勿將本產品放置在以下地方 : 本產品被暴露在高濕度 高溫或陽光直射的地方 ( 這可能會導致機能故障 ) 任何高溫或低溫的地方, 如冰箱 冰櫃 微波爐或烤箱 ( 這可能導致機能故障或損壞 ) 請勿處理堅硬的材料 ( 如硬肉 帶骨肉 ) 或粘性物質 ( 這可能會導致機能故障 ) 禁止使用的材料 : 附件 切刀切片刀 磨碎刀片及薯條製作刀片麵團刀片攪拌刀片切絲刀片沙律漏斗 壓榨器 攪拌機 乾碾磨機 說明 堅硬的材料, 粘性材料, 例如咖啡豆 乾大豆 速凍食品 乾魷魚等 硬度纖維高含量的材料 粘性材料 太軟的材料, 如硬的蔬菜 冷凍食物 火腿 薑黃 生薑 萵苣 西紅柿 桃子 巧克力等 不適合用於麵團制作的材料, 例如肉類 蔬菜 堅果 醬汁 抹醬 除了蛋清和鮮奶油, 任何其他材料 粘性材料 硬度纖維高含量的材料 過於細而薄的材料, 如山藥 芹菜 韭菜 鬆子等 大塊狀材料 軟和易碎的材料, 例如大蘿卜或土豆塊 西紅柿 豆腐 意大利麵 麵條等 除了柑橘類水果的任何其它材料, 如蘋果 獼猴桃等 堅硬的材料 高黏性成份的材料 水份少的材料, 如薑黃 乾大豆 冷凍食品 肉類 魚 水煮土豆或冰塊而已等 硬堅果 乾果 硬度纖維高含量的材料 濕潤的材料 液體, 如 : 各種堅果 葡萄乾 肉類 蔬菜 水煮雞蛋 薑黃等 使用前 : 請在乾淨 乾爽 平坦 堅固且順滑的表面上操作本產品, 及在使用前先擦乾淨橡膠腳墊 ( 第 6 頁 ) 以確保橡膠腳墊的吸力得以充分發揮 5

36 零件名稱 食物處理器 實際使用容量 :.5 公升. 壓料具. 給料口. 容器蓋罩 4. 切刀 5. 切絲刀片 6. 麵團刀片 7. 攪拌刀片 8. 漏斗蓋罩 9. 沙律漏斗 0. 刀片架. 幼磨碎刀片. 粗磨碎刀片 * 插頭形狀可能會與圖示有所不同 6. 薄切片刀 4. 厚切片刀 5. 薯條製作刀片 6. 榨汁器 7. 濾汁器 8. 容器 9. 轉軸 0. 馬達機座. 電源開關鈕. 橡膠腳墊. 電源線 4. * 插頭

37 部件名稱 攪拌機 乾碾磨機以及配件 實際使用容量 : 公升 中文. 攪拌機蓋罩. 攪拌機容器. 攪拌機切削刀 4. 碾磨機容器 5. 碾磨機切削刀 6. 碾磨機底座 7. 存儲箱 8. 刷子 控制盤 模式選擇 - 自動菜單 - 剁碎模式 斬切模式 凍結模式 糊膏模式 漏斗模式 - - 連續模式 間歇模式 脈衝開關鈕 模式光二極管顯示 停止 / 開始鈕於自動菜單 : 暫停 / 開始操作於手動菜單 : 停止 / 開始操作 旋轉刻度盤調整速度與計時 / 運作時間 速度與計時 / 運作時間光二極管顯示 : 將在手動菜單操作時亮起並由條塊顯示速度的等級 : 將在自動菜單操作時亮起並由條塊顯示計時 / 運作時間 摘要 : 在選擇一個功能後的 0 秒內如果沒有任何進一步的行動, 本產品的程序將暫停並自行復位 順時針方向轉動旋轉刻度盤將增加亮起的條塊數量, 反之亦然 連續模式和間歇模式的默認速度為最快速度,(0 級 ) 如果程序在操作時被暫停後並在 0 秒內沒有任何進一步的行動, 程序將暫停並自行復位 處理開始約 9 分鐘後, 連續模式將自動停止 ; 約 7 分鐘後, 間歇模式將自動停止 7

38 安全鎖 安全銷的設計是防止本產品在以下情況下被啟動 : - 容器蓋罩或濾汁器未與容器完全鎖定 - 容器 攪拌機容器或碾磨機容器未完全鎖定在馬達機座上 當容器蓋罩或濾汁器鎖定在容器上, 安全杆才會啓動安全銷 位置 A: 解鎖位置 B: 鎖定 安全銷 B A 完全鎖定步驟 : 容器及攪拌機容器, 如位置 A 所示, 對齊馬達機座上的三角形標記 順時針方向轉動, 直至聽到 喀嚓 的聲音, 而三角形標記現在對齊位置 B 乾碾磨機, 將它放到馬達機座上, 順時針方向轉動直至聽到 喀嚓 的聲音 解鎖時, 依照鎖定的方式以相反的步驟進行 摘要 : 請勿用任何工具, 棒狀物等來按壓安全銷和安全杆 請勿把液體或材料倒在安全銷和安全杆上 保持安全銷和安全杆的清潔, 避免異物顆粒積聚 上述行為將確保安全銷和安全杆的正常運行 如果不遵守, 將會損壞安全銷和安全杆的相關部分 電路自動斷路器及溫度感應保護 本產品備有電路自動斷路器及溫度感應器, 將在馬達負荷過重时, 使馬達停止運轉 ( 請參閱第 60 頁 ) 8

39 食物處理器 - 拆卸與組裝方法 - 從包裝狀態下拆卸 切刀頂部 中文 逆時針旋轉容器蓋罩, 然後從容器上拿起 握住切刀的頂部, 然後從容器中取出 摘要 : 當從容器中取出切刀時應小心鋒利的刀鋒 組裝食物處理器的附屬品 在首次使用本產品前, 我們強烈建議您清洗並完全擦乾所有的附屬品和配件, 請參閱第 頁的清洗方法 在組裝本產品時, 請拔掉插頭 在插入插頭前, 確保電源開關鈕已關閉 關於如何把馬達機座移位, 請參閱第 57 頁 收藏 切刀 麵團刀片 攪拌刀片 切絲刀片 或 4 或 或 將切刀 ( 麵團刀片 攪拌刀片 切絲刀片 ) 放入容器中 摘要 : 選用切刀時, 放入後, 請確保轉軸從切刀的頂部突出 將材料放入容器中 摘要 : 選用切絲刀片時, 請將材料分佈均勻的擺放在刀片上 將容器蓋罩蓋在容器上面, 順時針旋轉, 直到發出 喀嚓 的聲音 將壓料具放入給料口 9

IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should be followed, including the following: READ ALL INSTRUCTIONS BEF

IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should be followed, including the following: READ ALL INSTRUCTIONS BEF User Manual 用 户 手 册 Blender 搅 拌 器 For product and consumer services questions contact: Oster Consumer Service Mainland China: 008-6-68 www.oster.com.cn 0 Sunbeam Products, Inc. doing business as Jarden

More information

OA-253_H1~H4_OL.ai

OA-253_H1~H4_OL.ai WARNINGS Note: Read ALL the following BEFORE using this product. Follow all Guidelines at all times while using this product. CAUTION This warning indicates possibility of personal injury and material

More information

FP.pdf

FP.pdf 8 9 10 congee (see page 9) half bird dressed chicken 1/2 head lettuce 2 tbsp ginger juice 2 tbsp light soy sauce 1 tsp salt 1 tsp sugar 1 tbsp corn starch 1 tbsp oil 1 tsp sesame oil 1. 2. 3. 4. 1. Wash

More information

MK-F800 COVER

MK-F800 COVER Operating Instructions 操作說明 Buku Panduan Food Processor (Household Use) 食物攪拌機 ( 家庭用 ) Pemproses Makanan (Kegunaan di Rumah) Model No. 型號 No. Model Thank you for purchasing this Panasonic product. This

More information

untitled

untitled R ( ) .5..5 2.. 2.. 2 4 5 7 7 7 7 7 8 8 8 0 0 2 4 5 5 5 7 8 8 PC 0 安全注意事項及緊急處理方法 請務必遵守 警告 發生異常或故障時 應立即停止使用 拔 下電源插頭 恐會導致冒煙 起火 觸 電 異常或故障事例 即使接上電源開關有時也不會運轉 插拔電源線時 有時通電有時不通電 運轉中 有燒焦味或異音 本體部分變形或異常發熱 請立即連絡服務站進行檢查及修理

More information

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63>

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63> 2010 年 理 工 类 AB 级 阅 读 判 断 例 题 精 选 (2) Computer mouse How does the mouse work? We have to start at the bottom, so think upside down for now. It all starts with mouse ball. As the mouse ball in the bottom

More information

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

Bottle Feeding Your Baby - Simplified Chinese

Bottle Feeding Your Baby - Simplified Chinese Bottle Feeding Your Baby Bottle feeding with formula will meet your baby s food needs. Your doctor will help decide which formula is right for your baby. Never give milk from cows or goats to a baby during

More information

WFC40810

WFC40810 9000086873 (PD 85 05 10) Operating and Installation Instructions Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a 1-NEEDLE, 3-THREAD OVERLOCK SEWING MACHINE MO-623 INSTRUCTION MANUAL IMPORTANT: READ ALL SAFETY REGULATIONS CAREFULLY AND UNDERSTAND THEM BEFORE USING YOUR SEWING MACHINE. RETAIN THIS INSTRUCTION MANUAL

More information

WVT new

WVT new Operating and Installation Instructions 5120 004601 (PD 84 09 25) Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

BC04 Module_antenna__ doc

BC04 Module_antenna__ doc http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 1 of 10 http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 2 of 10 http://www.infobluetooth.com TEL:+86-23-68798999

More information

CANVIO_AEROCAST_CS_EN.indd

CANVIO_AEROCAST_CS_EN.indd 简 体 中 文...2 English...4 SC5151-A0 简 体 中 文 步 骤 2: 了 解 您 的 CANVIO AeroCast CANVIO AeroCast 无 线 移 动 硬 盘 快 速 入 门 指 南 欢 迎 并 感 谢 您 选 择 TOSHIBA 产 品 有 关 您 的 TOSHIBA 产 品 的 详 情, 请 参 阅 包 含 更 多 信 息 的 用 户 手 册 () 安

More information

UTI (Urinary Tract Infection) - Traditional Chinese

UTI (Urinary Tract Infection) - Traditional Chinese UTI (Urinary Tract Infection) Urinary tract infection, also called UTI, is an infection of the bladder or kidneys. Urethra Kidney Ureters Bladder Vagina Kidney Ureters Bladder Urethra Penis Causes UTI

More information

LH_Series_Rev2014.pdf

LH_Series_Rev2014.pdf REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check

More information

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact

More information

pdf

pdf THE INSTLLING INSTRUCTION FOR CONCELED TNK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

Microsoft Word - 3. Vitroefication_using_EMGP.docx

Microsoft Word - 3. Vitroefication_using_EMGP.docx EM GP 冷 冻 样 品 制 备 实 习 教 程 (Xiaojun Huang, Gang Ji) 每 位 演 示 及 带 领 学 员 实 习 EM GP 冷 冻 样 品 制 备 的 老 师 的 材 料 清 单 : 1)15 个 GIG 载 网 2) 冷 冻 样 品 Ferritin 或 Ribosome 3)EM GP 专 用 镊 子 1 把 4)1-10ul 移 液 器,1 把 ( 移 液 器

More information

1

1 Application Chuck Instruction Manual Universal Ball Lock Power Chuck APPLICATION CHUCK PBL CHUCK (UNIVERSAL BALL LOCK POWER CHUCK) TABLE OF CONTENTS Keep this manual handy for easy reference as it will

More information

Microsoft Word - PA-110E-REV.4-MGA繝・・繧ソ繧キ繝シ繝・P0-P3_-繝壹・繧ク菴咲スョ隱ソ謨エ.doc

Microsoft Word - PA-110E-REV.4-MGA繝・・繧ソ繧キ繝シ繝・P0-P3_-繝壹・繧ク菴咲スョ隱ソ謨エ.doc Pascal mag clamp Magnetic mold clamp model MGA DATA SHEET www.pascaleng.co.jp Specifications are subject to change without prior notice. Pamphlet PA-110E REV.6 2007.09 Calculation of Fixing Force Calculation

More information

Pneumonia - Traditional Chinese

Pneumonia - Traditional Chinese Pneumonia When you have pneumonia, the air sacs in the lungs fill with infection or mucus. Pneumonia is caused by a bacteria, virus or chemical. It is not often passed from one person to another. Signs

More information

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d WeChat Search Visual Identity Guidelines WEDESIGN 2018. 04 Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies

More information

入學考試網上報名指南

入學考試網上報名指南 入 學 考 試 網 上 報 名 指 南 On-line Application Guide for Admission Examination 16/01/2015 University of Macau Table of Contents Table of Contents... 1 A. 新 申 請 網 上 登 記 帳 戶 /Register for New Account... 2 B. 填

More information

Nebulizer Treatments - Simplified Chinese

Nebulizer Treatments - Simplified Chinese Nebulizer Treatments Some medicines need to be given through a nebulizer treatment. Nebulizer treatments are also called breathing treatments, aerosol treatments or med nebs. A nebulizer changes liquid

More information

Logitech Wireless Combo MK45 English

Logitech Wireless Combo MK45 English Logitech Wireless Combo MK45 Setup Guide Logitech Wireless Combo MK45 English................................................................................... 7..........................................

More information

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論 國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 一 教 育 學 系 簡 介... 1 ( 一 ) 成 立 時 間... 1 ( 二 ) 教 育 目 標 與 發 展 方 向... 1 ( 三 ) 授 課 師 資... 2 ( 四 ) 行 政 人 員... 3 ( 五 ) 核 心 能 力 與 課 程 規 劃... 3 ( 六 ) 空 間 環 境... 12 ( 七 )

More information

Male Circumcision - Traditional Chinese

Male Circumcision - Traditional Chinese Male Circumcision Male circumcision is the removal of the foreskin around the end of the penis. If you decide on circumcision, your baby s doctor will do it in the hospital s nursery. If your baby is small

More information

Male Circumcision - Simplified Chinese

Male Circumcision - Simplified Chinese Male Circumcision Male circumcision is the removal of the foreskin around the end of the penis. If you decide on circumcision, your baby s doctor will do it in the hospital s nursery. If your baby is small

More information

Slow Juicer Instruction Manual 慢磨機使用手冊

Slow Juicer Instruction Manual      慢磨機使用手冊 SJ2480 Slow Juicer Instruction Manual 慢 磨 機 使 用 手 冊 目 錄 重 要 安 全 資 訊 1 安 全 注 意 及 建 議 事 項 1-2 首 次 使 用 需 知 2 部 件 名 稱 3 使 用 前 安 裝 說 明 4-5 使 用 前 注 意 事 項 5 使 用 前 果 汁 食 材 準 備 需 知 6 使 用 前 雪 葩 食 材 準 備 需 知 7 使 用

More information

Rotary Switch Catalogue

Rotary Switch Catalogue Rotary Switches RS300/400/500 Series Outline Our RS series embody the manufacturing history of our company. All series are sturdy and solid with high dependability designed for control units of plants,

More information

FIGURE A

FIGURE A RYOBI in. TABLE SAW MODEL NUMBER RTS1 REPAIR SHEET 5 5 51 1 5 50 55 5 5 5 5 0 0 0 55 5 5 5 5 0 1 1 1 1 1 5 0 1 5 1 0 5 0 1 1 0 1 1 1 11 1 1 1 15 FIGURE A The model number will be found on a label attached

More information

Microsoft Word MasterCraft X-30_Maint.doc

Microsoft Word MasterCraft X-30_Maint.doc 2006 MasterCraft X30 Maintenance and Service Log MCX 350 Engine V Drive transmission Three ballast tanks Heater October 20, 2009 Table of Contents 2006 MasterCraft X30 1 1. Winterization 3 1.1 Engine (MCX

More information

0000Book_UC18YSL3.indb

0000Book_UC18YSL3.indb en UC 18YSL3 zh en zh Handling instructions 1 1 2 4 5 3 English 1 Rechargeable battery 2 Charge indicator lamp 3 Guide rail 4 Ventilation holes 5 Name plate 2 English GENERAL OPERATIONAL PRECAUTIONS 1.

More information

Microsoft Word - template.doc

Microsoft Word - template.doc HGC efax Service User Guide I. Getting Started Page 1 II. Fax Forward Page 2 4 III. Web Viewing Page 5 7 IV. General Management Page 8 12 V. Help Desk Page 13 VI. Logout Page 13 Page 0 I. Getting Started

More information

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2K K13 BLACK YRG BLUE YPK WHITE MODEL COLOR LIST UZ125X2 G22 Q05 GRAY ORANGE GREEN WHITE N28 W08 PREFACE When it becomes

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER L Series Features Coaxial shaft series L series Helical gears contribute to reduce vibration and noise. Standard backlash is 5 arc-min, ideal for precision control. High rigidity

More information

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt E15-3D1 Compact 4-Way Cassette type MMU-AP0071MH2UL MMU-AP0091MH2UL MMU-AP0121MH2UL MMU-AP0151MH2UL MMU-AP0181MH2UL Contents 1. Specifications 2. Dimensions 3. Center of gravity 4. Piping diagram 5. Wiring

More information

Template-A5

Template-A5 HR2170, HR2168, HR2167, HR2161, HR2160 2 20 3 11 1 HR2168, HR2167 17 10 16 15 9 8 21 20 14 7 13 19 6 23 5 12 18 22 HR2168, HR2167 HR2161, HR2160 HR2170 HR2168 HR2168, HR2167 HR2161 2 1 3 4 4 English 6

More information

01CP-WX3030WNetc_CO_ENG.indd

01CP-WX3030WNetc_CO_ENG.indd Data Video Projector User s Manual (Concise) ModelS: 8928A/8930A/8931WA/ 8933W Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please

More information

安 省 驾 照 中 文 考 题 007 版 页 码,/ C) 不 平 路 在 前 面 0 米 (00 英 尺 ) D) 火 车 路 在 前 A A) 目 的 地 指 示 牌 B) 学 校 区 域 小 心 儿 童 玩 耍 C) 省 公 园 D) 行 人 路 牌 A A) 学 校 巴 士 过 十 子 路

安 省 驾 照 中 文 考 题 007 版 页 码,/ C) 不 平 路 在 前 面 0 米 (00 英 尺 ) D) 火 车 路 在 前 A A) 目 的 地 指 示 牌 B) 学 校 区 域 小 心 儿 童 玩 耍 C) 省 公 园 D) 行 人 路 牌 A A) 学 校 巴 士 过 十 子 路 安 省 驾 照 中 文 考 题 007 版 页 码,/ 007--0 加 拿 大 安 大 略 省 驾 照 考 试 中 文 试 题 大 全 ONTARIO DRIVER'S LICENCE (G 笔 试 试 题 ) G 新 牌 考 取 年 内 买 汽 车 保 险 比 G 牌 便 宜, 购 买 最 优 惠 的 汽 车 保 险 问 题 请 咨 询 ( 安 省 ):6-858-0079 Robert,Email:

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER SSeries Coaxial shaft series Features S series Standard backlash is 3 arc-min, ideal for precision control. High rigidity & high torque were achived by uncaged needle roller

More information

Microsoft Word - ChineseSATII .doc

Microsoft Word - ChineseSATII .doc 中 文 SAT II 冯 瑶 一 什 么 是 SAT II 中 文 (SAT Subject Test in Chinese with Listening)? SAT Subject Test 是 美 国 大 学 理 事 会 (College Board) 为 美 国 高 中 生 举 办 的 全 国 性 专 科 标 准 测 试 考 生 的 成 绩 是 美 国 大 学 录 取 新 生 的 重 要 依

More information

LSC操作说明

LSC操作说明 1 C H R I S T A L P H A 1-4 LSC 型 Part. No. 102041 A L P H A 2-4 LSC 型 Part. No. 10204 冷 冻 干 燥 机 操 作 说 明 新 研 制 的 LSC-8 控 制 器, 具 备 图 形 显 示 功 能, 能 以 数 据 表 形 式 显 示 参 数, 并 可 选 配 控 制 软 件 LSC-8 1/4 VGA 大 屏 幕

More information

Please contact service agent approved by SHARP for servicing.

Please contact service agent approved by SHARP for servicing. MODEL 型 號 SJ-FR3C 原 裝 進 口 雪 櫃 使 用 說 明 書 雪 櫃 WARNING CAUTION BEFORE OPERATION DESCRIPTION OPERATION CARE AND CLEANING BEFORE CALLING FOR SERVICE 3 6 6 目 錄 警 告 安 全 注 意 事 項 使 用 之 前 各 部 件 名 稱 使 用 方 法 保 養 和

More information

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone,

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, respectively, and has been certified by the developer

More information

persons, including the following: 1. Read all instructions. 2. Check voltage to be sure that the voltage indicated on the nameplate agrees with your v

persons, including the following: 1. Read all instructions. 2. Check voltage to be sure that the voltage indicated on the nameplate agrees with your v READ BEFORE USE 使 用 前 阅 读 Visit www.hamiltonbeach.cn for our complete line of products and Use and Care Guides as well as delicious recipes, tips, and to register your product online! 有 关 我 们 所 有 系 列 产

More information

2015 Chinese FL Written examination

2015 Chinese FL Written examination Victorian Certificate of Education 2015 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Letter STUDENT NUMBER CHINESE FIRST LANGUAGE Written examination Monday 16 November 2015 Reading time: 11.45 am to 12.00

More information

CHINESE $WaP Vincent booklet

CHINESE $WaP Vincent booklet ELECTRICITY, GAS and WATER How to save money and help the environment 电, 天 然 气 和 水 如 何 省 钱 和 帮 助 改 善 环 境 CONTENTS Reach for the Stars Saving Energy Hot Water Heating & Cooling Refrigeration Lighting Cooking

More information

Microsoft Word - 00 表紙1-L版-1.doc

Microsoft Word - 00  表紙1-L版-1.doc IDX-OM-H005-L 初 版 :2003 年 7 月 改 定 :2005 年 7 月 使 用 说 明 书 冷 冻 式 空 气 干 燥 器 IDF1E-10 IDF2E-10 IDF3E-10 IDF3E-20 IDF4E-10 IDF4E-20 IDF6E-10 IDF6E-20 IDF8E-10 IDF8E-20 IDF11E-10 IDF11E-20 本 使 用 手 册 对 本 公 司 生

More information

HCD0174_2008

HCD0174_2008 Reliability Laboratory Page: 1 of 5 Date: December 23, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E Gerotor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 5 5 1 0 1 0 3 3 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 25mm Keyed (A) 1.0' 6T Spline

More information

: 205-03-311 5863 Series 0.35mm Pitch Board-to-Board Connector TABLE OF CONTENTS OUTLINE PART NAMES AND MODEL NUMBERS PART NAMES MODEL NUMBERS PRECAUTIONS IN HANDLING USING FOR BOARD-TO-BOARD CONNECTION

More information

Lorem ipsum dolor sit amet, consectetuer adipiscing elit

Lorem ipsum dolor sit amet, consectetuer adipiscing elit English for Study in Australia 留 学 澳 洲 英 语 讲 座 Lesson 3: Make yourself at home 第 三 课 : 宾 至 如 归 L1 Male: 各 位 朋 友 好, 欢 迎 您 收 听 留 学 澳 洲 英 语 讲 座 节 目, 我 是 澳 大 利 亚 澳 洲 广 播 电 台 的 节 目 主 持 人 陈 昊 L1 Female: 各 位

More information

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E Gerolor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 12 12 1 1 0 0 2 2 31 31 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 2mm Keyed (A) 1.0'

More information

BDERO100-TWZZ manual V3

BDERO100-TWZZ manual V3 1 4 5 2 3 A B 8 7 6 C D Oscillations 2.4mm 空載轉速 震動幅度 2.4mm 請注意! 各地區上市產品/配件不盡相同, 請依台灣 繁體中文說明書的內容為主 Warning! Attachments and accessories are not the same in each region, please only refer to Taiwan Traditional

More information

OVLFx3C7_Series_A3_bgry-KB.pub

OVLFx3C7_Series_A3_bgry-KB.pub (5 mm) x High brightness with well-defined spatial radiation patterns x U-resistant epoxy lens x Blue, green, red, yellow Product Photo Here Each device in the OLFx3C7 series is a high-intensity LED mounted

More information

HC20131_2010

HC20131_2010 Page: 1 of 8 Date: April 14, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

國立中山大學學位論文典藏.PDF

國立中山大學學位論文典藏.PDF 國 立 中 山 大 學 企 業 管 理 學 系 碩 士 論 文 以 系 統 動 力 學 建 構 美 食 餐 廳 異 國 麵 坊 之 管 理 飛 行 模 擬 器 研 究 生 : 簡 蓮 因 撰 指 導 教 授 : 楊 碩 英 博 士 中 華 民 國 九 十 七 年 七 月 致 謝 詞 寫 作 論 文 的 過 程 是 一 段 充 滿 艱 辛 與 淚 水 感 動 與 窩 心 的 歷 程, 感 謝 這 一

More information

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 3,,,,,, 1872,,,, 3 2004 ( 04BZS030),, 1 2005 5,,,,,,,,,,,,,,,,, 1928 716,1935 6 2682 1928 2 1935 6 1966, 2174, 7014 %, 94137 % 4, 1961, 59 1929,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 , :,,,, :,,,,,,

More information

穨control.PDF

穨control.PDF TCP congestion control yhmiu Outline Congestion control algorithms Purpose of RFC2581 Purpose of RFC2582 TCP SS-DR 1998 TCP Extensions RFC1072 1988 SACK RFC2018 1996 FACK 1996 Rate-Halving 1997 OldTahoe

More information

Microsoft Word - HC20138_2010.doc

Microsoft Word - HC20138_2010.doc Page: 1 of 7 Date: April 26, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

2015年4月11日雅思阅读预测机经(新东方版)

2015年4月11日雅思阅读预测机经(新东方版) 剑 桥 雅 思 10 第 一 时 间 解 析 阅 读 部 分 1 剑 桥 雅 思 10 整 体 内 容 统 计 2 剑 桥 雅 思 10 话 题 类 型 从 以 上 统 计 可 以 看 出, 雅 思 阅 读 的 考 试 话 题 一 直 广 泛 多 样 而 题 型 则 稳 中 有 变 以 剑 桥 10 的 test 4 为 例 出 现 的 三 篇 文 章 分 别 是 自 然 类, 心 理 研 究 类,

More information

. Land Patterns for Reflow Soldering.Recommended Reflow Soldering Conditions (For Lead Free) TYPE PID0703 PID0704 PID1204 PID1205 PID1207 PID1209 L(mm

. Land Patterns for Reflow Soldering.Recommended Reflow Soldering Conditions (For Lead Free) TYPE PID0703 PID0704 PID1204 PID1205 PID1207 PID1209 L(mm .Features: 1.Magnetic Shielded surface mount inductor with high current rating. 2.Low resistance to keep power loss minimum..applications: Excellent for power line DC-DC conversion applications used in

More information

TX-NR3030_BAS_Cs_ indd

TX-NR3030_BAS_Cs_ indd TX-NR3030 http://www.onkyo.com/manual/txnr3030/adv/cs.html Cs 1 2 3 Speaker Cable 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT 1 DIGITAL OPTICAL OUT AUDIO OUT TV 3 1 5 4 6 1 2 3 3 2 2 4 3 2 5

More information

Microsoft PowerPoint - AWOL - Acrobat Windows Outlook.ppt [Compatibility Mode]

Microsoft PowerPoint - AWOL - Acrobat Windows Outlook.ppt [Compatibility Mode] AWOL Windows - Tips & Tricks Resolution, color depth & refresh rate Background color Service packs Disk cleanup (cleanmgr) Disk defragmentation AWOL Windows Resolution, Color Depth & Refresh Rate The main

More information

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU Lithium-ion Battery UN38.3 Test Report Recommendations on the TRANSPORT OF DANGEROUS GOODS (Manual of Tests and Criteria, Fifth revised edition, Amend.2) Customer: Lenovo Model: L15M3PB2 Rating: 11.25V,

More information

HC50246_2009

HC50246_2009 Page: 1 of 7 Date: June 2, 2009 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

套 餐 Set 蕃 茄 濃 湯 套 餐 Tomato Bisque Soup 蕃 茄 濃 湯 鍋 底, 選 配 A 或 B 套 餐 一 款 Included : choosing Set A Or Set B A. 黑 豚 肉 套 餐 Sliced Black Pork Packages 加 拿 大

套 餐 Set 蕃 茄 濃 湯 套 餐 Tomato Bisque Soup 蕃 茄 濃 湯 鍋 底, 選 配 A 或 B 套 餐 一 款 Included : choosing Set A Or Set B A. 黑 豚 肉 套 餐 Sliced Black Pork Packages 加 拿 大 元 州 分 店 禾 輋 分 店 沙 角 分 店 翠 林 分 店 火 鍋 Hot Pot 雞 煲 Chicken Hot Pot 土 佬 雞 煲 半 隻 Half Spicy Chicken Hot Pot in Sichuan Special 一 隻 Whole Style 海 南 島 椰 子 雞 半 隻 Half Coconut Chicken in Hainan Style 一 隻 Whole

More information

東莞工商總會劉百樂中學

東莞工商總會劉百樂中學 /2015/ 頁 (2015 年 版 ) 目 錄 : 中 文 1 English Language 2-3 數 學 4-5 通 識 教 育 6 物 理 7 化 學 8 生 物 9 組 合 科 學 ( 化 學 ) 10 組 合 科 學 ( 生 物 ) 11 企 業 會 計 及 財 務 概 論 12 中 國 歷 史 13 歷 史 14 地 理 15 經 濟 16 資 訊 及 通 訊 科 技 17 視 覺

More information

Microsoft Word - 100999_HowUseInsulinPen_ChiTr-DTP-UPDATED-ED-HD.doc

Microsoft Word - 100999_HowUseInsulinPen_ChiTr-DTP-UPDATED-ED-HD.doc How to Use an Insulin Pen Select the Site for Injection Sites which can be used are: Back of upper arms Abdomen (around navel) Front and side area of thighs Back above waist Buttocks Stay 1 inch away from

More information

Microsoft Word - 第四組心得.doc

Microsoft Word - 第四組心得.doc 徐 婉 真 這 四 天 的 綠 島 人 權 體 驗 營 令 我 印 象 深 刻, 尤 其 第 三 天 晚 上 吳 豪 人 教 授 的 那 堂 課, 他 讓 我 聽 到 不 同 於 以 往 的 正 義 之 聲 轉 型 正 義, 透 過 他 幽 默 熱 情 的 語 調 激 起 了 我 對 政 治 的 興 趣, 願 意 在 未 來 多 關 心 社 會 多 了 解 政 治 第 一 天 抵 達 綠 島 不 久,

More information

Microsoft Word - LR1122B-B.doc

Microsoft Word - LR1122B-B.doc UNISONIC TECHNOLOGIES CO., LTD LOW NOISE ma LDO REGULATOR DESCRIPTION The UTC is a typical LDO (linear regulator) with the features of High output voltage accuracy, low supply current, low ON-resistance,

More information

(0507)ES-WF20 30.indd

(0507)ES-WF20 30.indd 使 用 说 明 书 ( 家 用 ) 美 容 修 剪 器 型 号 ES-WF20 ES-WF30 中 文 3 English 15 2 使 用 说 明 书 ( 家 用 ) 美 容 修 剪 器 型 号 ES-WF20 ES-WF30 中 文 目 录 安 全 注 意 事 项...4 使 用 须 知... 6 部 件 名 称... 7 电 池 的 安 装 及 寿 命... 8 替 换 刀 刃 的 安 装 和

More information

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for Doreen Virtue, Ph.D. Charles Virtue C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for a Sign... 27 7.

More information

双 针 二 / 三 / 四 / 五 线 包 缝 机 操 作 指 南 要 领 : 在 您 使 用 缝 纫 机 之 前, 请 仔 细 阅 读 并 理 解 所 有 的 安 全 操 作 规 程 重 要 的 安 全 操 作 规 则 重 点 安 全 说 明 : 由 于 本 机 器 有 电 器 装 置, 所 以 在 使 用 前 必 须 时 刻 注 意 最 基 本 的 安 全 规 则, 阅 读 所 有 操 作 说

More information

HC70245_2008

HC70245_2008 Reliability Laboratory Page: 1 of 6 Date: September 5, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family small, speedy, safe Eextremely modular Up to 64 modules per bus de Quick reaction time: up to 20 µs A new Member of the Cube Family Murrelektronik s modular I/O system expands the field-tested Cube family

More information

Manual Pulse Generator Catalogue

Manual Pulse Generator Catalogue Manual Pulse Generator RE45T series Outline RE45T/V series are compact optical manual pulse generators that allow accurate and smooth manual motion for NC machine tools, industrial machines etc. Features

More information

國立中山大學學位論文典藏.PDF

國立中山大學學位論文典藏.PDF I II III The Study of Factors to the Failure or Success of Applying to Holding International Sport Games Abstract For years, holding international sport games has been Taiwan s goal and we are on the way

More information

pdf

pdf 88% 84% OK 1 3 1.1 1.2 1.3 (1) (1) (1) 1/7/2013 (2) (3) (2) (2) 1/7/2013 (4) (5) (6) (7) (3) (4) (3) (4) (5) 1/7/2013 1/7/2013 1/7/2013 (6) 1/7/2013 2 (7) 1/9/2013 2.1 (8) 1/9/2013 (9) 1/12/2013 2.2 2.3

More information

ch_code_infoaccess

ch_code_infoaccess 地 產 代 理 監 管 局 公 開 資 料 守 則 2014 年 5 月 目 錄 引 言 第 1 部 段 數 適 用 範 圍 1.1-1.2 監 管 局 部 門 1.1 紀 律 研 訊 1.2 提 供 資 料 1.3-1.6 按 慣 例 公 布 或 供 查 閱 的 資 料 1.3-1.4 應 要 求 提 供 的 資 料 1.5 法 定 義 務 及 限 制 1.6 程 序 1.7-1.19 公 開 資

More information

untitled

untitled 20 90 1998 2001 1 Abstract Under the environment of drastic competitive market, risk and uncertainty that the enterprise faces are greater and greater, the profit ability of enterprise assets rises and

More information

601988 2010 040 113001 2010 8 26 2010 8 12 2010 8 26 15 15 2010 15 0 0 15 0 0 6035 20022007 20012002 19992001 200720081974 1999 2010 20082008 2000 197

601988 2010 040 113001 2010 8 26 2010 8 12 2010 8 26 15 15 2010 15 0 0 15 0 0 6035 20022007 20012002 19992001 200720081974 1999 2010 20082008 2000 197 BANK OF CHINA LIMITED 3988 2010 8 26 ** ** *** # Alberto TOGNI # # # * # 1 601988 2010 040 113001 2010 8 26 2010 8 12 2010 8 26 15 15 2010 15 0 0 15 0 0 6035 20022007 20012002 19992001 200720081974 1999

More information

Microsoft Word - AP1515V02

Microsoft Word - AP1515V02 Document No. Rev.: V0.20 Page: 1 of 9 Revision History Rev. DRN # History Initiator Effective Date V01 V02 Initial document 黃宗文 Add second package description 葉宗榮 2014/05/15 2015/09/08 Initiator: 雷晨妤 (DCC)

More information

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl INSTRUCTIONS MANUAL SMOKE DETECTOR COLOR, B/W CCD CAMERA CONTENTS English / Chinese PREFACE SAFETY INSTRUCTIONS FUNCTION DESCRIPTION INSTALLATION SPECIFICATIONS PR0210SDE2 Thank you very much for purchasing

More information

5in1_eDVR_Manual_Chinese.cdr

5in1_eDVR_Manual_Chinese.cdr 02 English User Manual 29 User Manual Contents 2 5 6 7 8 9 10 11 12 14 17 18 19 20 21 22 23 24 25 26 27 Quick start Controls Accessories Minimum System Requirements Battery Charge Power On/Off LCM Indicator

More information

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn Xi III Zebra XI III 1 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn 230V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666

More information

Ryobi 10 in. Sliding Compound Miter Saw With Laser Model No. TSS102L Repair Sheet 0 1 2 3 4 62 65 5 6 36 68 6 8 69 6 9 80 81 6 66 40 82 23 3 4 6 44 43 4 45 50 46 52 48 49 51 59 55 54 53 60 5 61 40 58 63

More information

010 X Watch out for traffic signals 011 X Bumpy road 012 O Tunnel ahead 013 X Bicycles prohibited 014 O Yield 015 O Single lane road, pass with extrem

010 X Watch out for traffic signals 011 X Bumpy road 012 O Tunnel ahead 013 X Bicycles prohibited 014 O Yield 015 O Single lane road, pass with extrem 001 X Winding road, left turn ahead 002 O Forked road 003 X Bump ahead 004 O Steep downgrade ahead 005 O Narrow bridge 006 X Narrow Road 007 X Narrow road 008 O No-gate railroad crossing 009 O Watch out

More information

<4D6963726F736F667420506F776572506F696E74202D20C6F3D2B5BCB0B2FAC6B7BCF2BDE92DD6D0D3A2CEC420C1F5B9FAD3B1205BBCE6C8DDC4A3CABD5D>

<4D6963726F736F667420506F776572506F696E74202D20C6F3D2B5BCB0B2FAC6B7BCF2BDE92DD6D0D3A2CEC420C1F5B9FAD3B1205BBCE6C8DDC4A3CABD5D> 企 业 及 产 品 简 介 COMPANY & PRODUCTS INTRODUCTION 山 东 泗 水 康 得 新 复 合 材 料 有 限 公 司 SHANDONG SISHUI KANGDE XIN COMPOSITE MATERIAL CO., LTD. 集 团 概 况 KDXGROUP OVERVIEW 1 拥 有 两 大 产 业 群 : 预 涂 膜 和 光 学 膜 1. GROUP HAS

More information

untitled

untitled Co-integration and VECM Yi-Nung Yang CYCU, Taiwan May, 2012 不 列 1 Learning objectives Integrated variables Co-integration Vector Error correction model (VECM) Engle-Granger 2-step co-integration test Johansen

More information

ai

ai POPSICLE Y LEXA 80-901-1/-/-7/-0 or indoor domes c use / March 018-01 Designed in Denmark, made in Europe 80-901-1/-/-7/-0 A 3930-10030 Ø10x30mm x8 C D 3930-1000 Ø10x0mm x1 E 3917-1001 M10x1mm x1 J 033-00

More information

untitled

untitled NEW Register your product on line J 80 Ultra J 100 Ultra www.robot-coupe.com Register your product on line Head Office, French, Export and Marketing Department: 48, rue des Vignerons 94305 Vincennes Cedex-

More information

124 第十三期 Conflicts in the Takeover of the Land in Taiwan after the Sino-Japanese War A Case in the Change of the Japanese Names of the Taiwanese Peopl

124 第十三期 Conflicts in the Takeover of the Land in Taiwan after the Sino-Japanese War A Case in the Change of the Japanese Names of the Taiwanese Peopl 123 戰後初期臺灣土地接收的糾紛 以更改日式姓名的臺人遭遇為例 124 第十三期 Conflicts in the Takeover of the Land in Taiwan after the Sino-Japanese War A Case in the Change of the Japanese Names of the Taiwanese People Abstract By Ho Fung-jiao

More information

8016_2_1page

8016_2_1page VARICONTM PART NUMBERING SYSTEM 00 NO. NUMBER OF CONTACTS 20=020, 38=038, 56=056, 90=090, 120=120 CONTACT CODE INSULATOR V=Standard Type HV=For High Voltage ( ) ( NO. OF CONTACTS) 20,38,56,90,120 (PITCH

More information

70 莫 加 杏 仁 長 芭 芙 Mocha Almond Puff 72 芒 果 芭 芙 層 層 疊 Mango Puff Layers 74 蟹 柳 鷄 蛋 沙 律 泡 芙 Crab Meat and Egg Salad Puff 76 脆 脆 芭 芙 Crispy Puff 78 燭 光 約

70 莫 加 杏 仁 長 芭 芙 Mocha Almond Puff 72 芒 果 芭 芙 層 層 疊 Mango Puff Layers 74 蟹 柳 鷄 蛋 沙 律 泡 芙 Crab Meat and Egg Salad Puff 76 脆 脆 芭 芙 Crispy Puff 78 燭 光 約 目 錄 1 2 推 薦 序 3 前 言 第 一 次 做 西 點 就 能 打 動 你 的 心 清 蛋 糕 的 大 變 身 8 原 味 牛 油 蛋 卷 Egg Roll 10 日 式 蜂 蜜 蛋 卷 Honey Roll in Japanese Style 12 抹 茶 紅 豆 蛋 卷 Mocha and Red Bean Roll 14 焦 糖 天 使 蛋 卷 Angel Caramel Roll 16

More information

酸 萝 卜 炖 老 鸭 盐 水 鸭 19 水 鸭 润 肺 汤 菠 萝 炒 鸭 片 麻 辣 鸭 胗 SEASHELL PASTA SALAD 油 炸 香 菇 炒 圆 白 菜 20 糖 醋 莲 花 白 ( 糖 醋 包 心 菜 ) 蒸 茄 夹 肉 末 茄 子 鱼 香 茄 子 蒜 香 咸 鱼 干 焖 茄 子

酸 萝 卜 炖 老 鸭 盐 水 鸭 19 水 鸭 润 肺 汤 菠 萝 炒 鸭 片 麻 辣 鸭 胗 SEASHELL PASTA SALAD 油 炸 香 菇 炒 圆 白 菜 20 糖 醋 莲 花 白 ( 糖 醋 包 心 菜 ) 蒸 茄 夹 肉 末 茄 子 鱼 香 茄 子 蒜 香 咸 鱼 干 焖 茄 子 香 橙 烧 猪 肉 条 4 腊 肠 鱼 香 碎 滑 鸡 山 椒 拌 白 肉 家 常 连 锅 四 川 合 川 肉 片 醉 妃 白 肉 梅 菜 芋 头 扣 肉 东 坡 肉 5 腐 乳 肉 蚂 蚁 上 树 鱼 香 肉 丝 粉 丝 煲 碗 仔 翅 川 肉 丝 盐 煎 肉 6 叉 烧 肉 肉 丸 糊 辣 汤 辣 味 肉 皮 冻 鲜 香 肉 皮 冻 溜 肉 段 糖 醋 咕 噜 肉 苦 瓜 镶 肉 豆 豉 ( 豉

More information

2 IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read and save

2 IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read and save READ BEFORE USE 使 用 前 阅 读 Visit www.hamiltonbeach.cn for our complete line of products and Use and Care Guides as well as delicious recipes, tips, and to register your product online! 有 关 我 们 所 有 系 列 产

More information