12.pdf

Size: px
Start display at page:

Download "12.pdf"

Transcription

1 对 帧 中 继 配 置 与 故 障 排 除 的 全 面 的 指 南 交 互 : 本 文 档 对 您 的 Cisco 设 备 进 行 自 定 义 分 析 目 录 简 介 开 始 使 用 前 规 则 先 决 条 件 使 用 的 组 件 背 景 理 论 配 置 基 本 的 帧 中 继 网 络 图 配 置 debug 和 show 命 令 配 置 星 形 帧 中 继 网 络 图 配 置 显 示 命 令 分 支 间 连 接 配 置 显 示 命 令 配 置 帧 中 继 子 接 口 点 到 点 子 接 口 显 示 命 令 星 型 连 接 子 接 口 显 示 命 令 配 置 多 点 子 接 口 的 动 态 和 静 态 映 射 网 络 图 配 置 debug 和 show 命 令 配 置 IP 无 编 号 帧 中 继 网 络 图 配 置 显 示 命 令 配 置 帧 中 继 备 份 ISDN 上 的 帧 中 继 备 份 配 置 每 个 DCLI 备 份 带 有 拨 号 程 序 配 置 文 件 的 星 型 网 配 置 帧 中 继 交 换 网 络 图 配 置 显 示 命 令 配 置 帧 中 继 DLCI 优 先 级 实 施 注 意 事 项 网 络 图 配 置 debug 和 show 命 令 帧 中 继 广 播 队 列 流 量 整 形 流 量 整 形 参 数 一 般 流 量 整 形 帧 中 继 流 量 整 形 常 用 帧 中 继 命 令 show frame-relay pvc show frame-relay map 帧 中 继 和 桥 接 帧 中 继 和 内 存 帧 中 继 的 故 障 排 查

2 "Serial0 is down, line protocol is down" "Serial0 is up, line protocol is down" "Serial0 is up, line protocol is up" 帧 中 继 特 性 IP 分 界 检 查 Ping 多 点 帧 中 继 上 您 自 己 的 IP 地 址 关 键 字 广 播 重 新 配 置 子 接 口 DLCI 限 制 IP/IPX/AT 地 址 RIP 和 IGRP Keepalive 串 行 接 口 OSPF 和 多 点 来 源 相 关 信 息 简 介 帧 中 继 是 行 业 标 准, 交 换 数 据 链 路 层 协 议 该 把 柄 多 个 虚 拟 电 路 使 用 在 连 接 的 设 备 之 间 的 高 级 数 据 链 路 控 制 (HDLC) 封 装 在 许 多 情 况 下, 帧 中 继 比 X.25 更 有 效 率,X.25 是 一 般 考 虑 替 换 的 协 议 以 下 图 说 明 一 个 帧 中 继 帧 (ANSI T1.618) 注 意 在 上 图 中,Q.922 地 址 ( 如 当 前 定 义 ) 是 2 个 八 位 字 节, 并 包 含 10-bit 数 据 链 路 连 接 标 识 符 (DLCI) 在 一 些 网 络 中,Q.922 地 址 可 能 被 随 意 增 加 到 三 个 或 四 个 八 位 位 组 标 志 领 域 分 隔 帧 的 开 始 处 和 结 束 在 主 导 的 " flag " 字 段 之 后 是 两 字 节 的 地 址 信 息 这 两 个 字 节 的 十 位 数 组 成 了 实 际 电 路 ID( 称 为 DLCI, 用 于 数 据 链 路 连 接 标 识 符 ) 10 位 DLCI 值 是 帧 中 继 报 头 的 重 点 它 识 别 多 元 化 到 物 理 信 道 的 逻 辑 连 接 在 基 本 的 ( 即 不 由 本 地 管 理 接 口 [LMI] 进 行 扩 展 ) 寻 址 模 式 中,DLCI 有 本 地 意 义 ; 即 二 个 不 同 连 接 端 的 终 端 设 备 可 以 在 相 同 连 接 上 使 用 不 同 的 DLCI 开 始 使 用 前 规 则

3 有 关 文 档 规 则 的 详 细 信 息, 请 参 阅 Cisco 技 术 提 示 规 则 先 决 条 件 欲 知 更 多 信 息 和 本 文 所 用 术 语 的 定 义, 请 参 见 帧 中 继 术 语 表 使 用 的 组 件 本 文 档 不 限 于 特 定 的 软 件 和 硬 件 版 本 本 文 档 中 的 信 息 都 是 基 于 特 定 实 验 室 环 境 中 的 设 备 创 建 的 本 文 档 中 使 用 的 所 有 设 备 最 初 均 采 用 原 始 ( 默 认 ) 配 置 如 果 您 是 在 真 实 网 络 上 操 作, 请 确 保 您 在 使 用 任 何 命 令 前 已 经 了 解 其 潜 在 影 响 背 景 理 论 帧 中 继 最 初 被 设 想 了 作 为 一 份 协 议 为 在 ISDN 接 口 的 使 用 1984 年, 初 步 提 议 被 提 交 到 国 际 电 信 联 盟 电 信 标 委 员 会 准 化 部 门 (ITU-T) ( 以 前 的 国 际 电 报 电 话 咨 询 委 员 会 [CCITT]) 帧 中 继 的 工 作 也 可 以 在 美 国 ANSI 认 可 的 T1S1 标 准 委 员 会 里 执 行 1990 年, 思 科 系 统 StrataCom Northern Telecom 和 Digital Equipment Corporation 组 建 了 一 个 机 构, 专 门 从 事 帧 中 继 技 术 的 开 发, 加 快 可 互 操 作 的 帧 中 继 产 品 的 推 出 他 们 制 定 了 一 个 规 范, 符 合 在 T1S1 和 ITU-T 中 讨 论 的 基 本 帧 中 继 协 议, 但 在 功 能 方 面 进 行 了 扩 展, 提 供 了 一 些 适 用 于 复 杂 联 网 环 境 的 其 他 功 能 这 些 帧 中 继 扩 展 共 同 指 LMI 这 是 在 路 由 器 的 cisco LMI 与 ansi 或 "q933a" LMI 相 对 帧 中 继 提 供 了 分 组 交 换 数 据 通 信 功 能, 可 在 用 户 设 备 ( 例 如 路 由 器 网 桥 主 机 ) 和 网 络 设 备 ( 例 如 交 换 节 点 ) 之 间 的 接 口 上 使 用 用 户 设 备 经 常 称 为 数 据 终 端 设 备 (DTE), 连 接 到 DTE 的 网 络 设 备 通 常 称 为 数 据 电 路 终 端 设 备 (DCE) 提 供 帧 中 继 接 口 的 网 络 可 以 是 运 营 商 提 供 的 公 共 网 络 或 为 单 个 企 业 服 务 的 专 有 设 备 网 络 帧 中 继 与 在 其 功 能 和 格 式 的 X.25 极 大 有 所 不 同 特 别 是, 帧 中 继 是 更 多 效 率 化 的 协 议, 实 现 高 性 能 和 更 加 了 不 起 的 效 率 作 为 用 户 和 网 络 设 备 之 间 的 一 个 接 口, 帧 中 继 提 供 了 一 种 在 单 个 物 理 传 输 链 路 上 统 计 复 用 很 多 逻 辑 数 据 会 话 ( 指 虚 拟 电 路 ) 的 方 式 这 与 使 用 支 持 多 数 据 流 的 仅 Time Division Multiplexing (TDM) 技 术 的 系 统 形 成 对 比 帧 中 继 的 统 计 复 用 提 供 可 用 的 带 宽 灵 活 和 有 效 利 用 无 需 TDM 技 术 它 也 可 以 使 用, 或 者 由 TDM 系 统 提 供 在 信 道 顶 部 帧 中 继 的 另 一 个 重 要 特 性 是 它 开 发 了 广 域 网 (WAN) 传 输 技 术 的 最 新 进 展 当 模 拟 传 输 传 动 系 统 和 铜 媒 体 是 主 要 的, 更 早 的 广 域 网 协 议, 例 如 X.25, 开 发 这 些 链 路 比 光 纤 媒 体 / 数 字 传 输 链 路 联 机 今 天 较 不 可 靠 在 这 类 链 路 上, 链 路 层 协 议 可 以 抛 弃 耗 费 时 间 长 的 错 误 改 正 算 法, 将 这 类 算 法 留 在 更 高 协 议 层 上 执 行 因 此 更 加 了 不 起 的 性 能 和 效 率 是 可 能 的, 无 需 牺 牲 数 据 完 整 性 帧 中 继 设 计 有 此 方 法 的 念 头 它 包 括 循 环 冗 余 校 验 (CRC) 算 法, 用 于 检 测 损 坏 的 位 ( 可 能 导 致 数 据 丢 弃 ), 但 不 包 括 任 何 用 于 纠 正 坏 数 据 ( 例 如, 在 这 个 水 平 的 协 议 上 重 新 转 发 ) 的 任 何 协 议 机 制 帧 中 继 和 X.25 之 间 的 另 一 个 区 别 是 帧 中 继 中 缺 乏 明 确 的 每 条 虚 拟 电 路 的 流 控 制 即 然 许 多 上 层 协 议 能 够 有 效 执 行 它 们 自 己 的 流 控 制 算 法, 因 此 链 路 层 对 此 功 能 的 需 求 已 经 减 少 帧 中 继, 因 此, 不 包 括 在 更 高 层 复 制 那 些 的 明 确 流 控 制 程 序 相 反 地, 使 用 非 常 简 单 的 拥 塞 通 知 机 制 是 为 了 使 网 络 通 知 用 户 设 备 现 在 网 络 资 源 接 近 拥 塞 状 态 此 通 知 能 警 告 更 高 层 协 议 流 量 控 制 可 能 是 需 要 的 配 置 基 本 的 帧 中 继 一 旦 您 在 永 久 虚 拟 电 路 (PVC) 的 两 端 具 有 到 本 地 帧 中 继 交 换 机 的 可 靠 连 接, 便 需 开 始 规 划 帧 中 继 配 置 在 此 第 一 示 例 中, 对 cisco LMI 的 本 地 管 理 接 口 (LMI) 型 的 默 认 在 " 接 口 被 默 认 为 "" 多 点 "" 接 口, 因 此 frame-relay inverse-arp 是 打 开 的 ( 对 于 点 到 点 的 应 用 而 言, 这 里 没 有 反 向 ARP) "IP 水 平 分 割 检 查 默 认 禁 用 帧 中 继 封 装, 路 由 更 新 将 从 相 同 接 口 流 入 流 出 路 由 器 通 过 LMI 更 新, 获 取 它 们 需 要 从 帧 中 继 交 换 机 使 用 的 数 据 链 路 连 接 标 识 符 (DLCI) 路 由 器 将 反 向 ARP 传 输 到 远 程 IP 地 址 上, 并 创 建 本 地 DLCI 和 相 关 远 程 IP 地 址 的 映 射 网 络 图 配 置 #show running-config Building configuration...

4 Current configuration : 1705 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial0 ip address frame-relay interface-dlci 140 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1499 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 150 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end debug 和 show 命 令 在 发 出 debug 命 令 之 前, 请 参 阅 有 关 Debug 命 令 的 重 要 信 息 show frame-relay map show frame-relay pvc show frame-relay lmi

5 ping <device name> show ip route #show frame-relay map Serial0 (up): ip dlci 140(0x8C,0x20C0), dynamic, broadcast,, status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 83 output pkts 87 in bytes 8144 out bytes 8408 dropped pkts 0 in FECN pkts0 in BECN pkts 0 out FECN pkts 0 out BECN pkts0 out bcast pkts 41 out bcast bytes 3652 pvc create time 01:31:50, last time pvc status changed 01:28:28 #show frame-relay lmi LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 550 Num Status msgs Rcvd 552 Num Update Status Rcvd 0 Num Status Timeouts 0 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 R /8 [120/1] via , 00:00:08, Serial0 #show frame-relay map Serial1 (up): ip dlci 150(0x96,0x2460), dynamic, broadcast,, status defined, active #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1 input pkts 87 output pkts 83 in bytes 8408 out bytes 8144 dropped pkts 0 in FECN pkts 0 out bcast pkts 38 out bcast bytes 3464 pvc create time 01:34:29, last time pvc status changed 01:28:05 #show frame-relay lmi LMI Statistics for interface Serial1 (Frame Relay DTE) LMI TYPE = CISCO Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0

6 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 569 Num Status msgs Rcvd 570 Num Update Status Rcvd 0 Num Status Timeouts 0 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, Serial1 R /8 [120/1] via , 00:00:19, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 配 置 星 形 帧 中 继 在 本 例 中, 路 由 器 知 道 它 使 用 了 哪 些 来 自 帧 中 继 交 换 机 的 数 据 链 路 连 接 标 识 符 (DLCI), 并 将 它 们 分 配 到 主 接 口 然 后 路 由 器 远 程 IP 地 址 的 反 向 ARP 注 意 : 除 非 您 在 每 个 末 端 明 确 添 加 了 帧 中 继 映 射, 否 则 您 不 便 不 能 够 从 Aton,ping 通 的 串 行 IP 地 址 如 果 已 经 正 确 配 置 路 由, 在 LAN 上 生 成 的 数 据 流 不 会 出 现 故 障 如 果 在 扩 展 的 ping 中 将 以 太 网 IP 地 址 用 作 源 地 址, 您 就 能 实 现 Ping 操 作 当 帧 中 继 Inverse-arp 启 用, 默 认 情 况 下 广 播 IP 流 量 在 连 接 将 出 去 网 络 图 配 置 Aton spicey#show running-config Building configuration... version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname spicey interface Ethernet0 ip address interface Serial0 ip address frame-relay interface-dlci 130

7 frame-relay interface-dlci 140 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end prasit#show running-config Building configuration... Current configuration : 1499 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname prasit interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 150 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end Aton aton#show running-config Building configuration... Current configuration: version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption hostname aton interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 160 router rip network network

8 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end 显 示 命 令 show frame-relay map show frame-relay pvc ping <device name> spicey#show frame-relay map Serial0 (up): ip dlci 140(0x8C,0x20C0), dynamic, broadcast,, status defined, active Serial0 (up): ip dlci 130(0x82,0x2020), dynamic, broadcast,, status defined, active spicey#show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 130, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 32 output pkts 40 in bytes 3370 out bytes 3928 dropped pkts 0 in FECN pkts 0 out bcast pkts 30 out bcast bytes 2888 pvc create time 00:15:46, last time pvc status changed 00:10:42 DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 282 output pkts 291 in bytes out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 223 out bcast bytes pvc create time 02:28:36, last time pvc status changed 02:25:14 spicey# spicey#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms spicey#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms prasit#show frame-relay map Serial1 (up): ip dlci 150(0x96,0x2460), dynamic, broadcast,, status defined, active prasit#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1 input pkts 311 output pkts 233 in bytes out bytes dropped pkts 0 in FECN pkts 0

9 out bcast pkts 162 out bcast bytes pvc create time 02:31:39, last time pvc status changed 02:25:14 prasit#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms prasit#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds:... Success rate is 0 percent (0/5) Aton aton#show frame-relay map Serial1 (up): ip dlci 160(0xA0,0x2800), dynamic, broadcast,, status defined, active aton#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 160, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1 input pkts 35 output pkts 32 in bytes 3758 out bytes 3366 dropped pkts 0 in FECN pkts 0 out bcast pkts 27 out bcast bytes 2846 pvc create time 00:10:53, last time pvc status changed 00:10:53 aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds:... Success rate is 0 percent (0/5) 分 支 间 连 接 在 使 用 多 点 接 口 的 星 型 结 构 中, 您 不 能 从 一 个 支 路 ping 通 另 一 个 支 路, 因 为 没 有 其 他 支 路 的 IP 地 址 映 射 仅 集 线 器 地 址 通 过 反 向 地 址 解 析 协 议 (IARP) 了 解 如 果 您 使 用 frame-relay map 命 令, 将 远 程 支 路 的 IP 地 址 配 置 静 态 映 射, 以 使 用 本 地 的 数 据 链 路 连 接 标 识 符 (DLCI), 您 也 能 够 ping 其 他 支 路 的 地 址 配 置 prasit#show running-config interface Ethernet0

10 ip address interface Serial ip address frame-relay map ip frame-relay interface-dlci 150 显 示 命 令 show frame-relay map ping <device name> show running-config Aton prasit#show frame-relay map Serial1 (up): ip dlci 150(0x96,0x2460), dynamic, broadcast,, status defined, active Serial1 (up): ip dlci 150(0x96,0x2460), static, CISCO, status defined, active prasit#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 68/70/80 ms prasit#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 64/67/76 ms aton#show running-config interface Ethernet0 ip address interface Serial1 ip address no ip directed-broadcast frame-relay map ip frame-relay interface-dlci 160 aton#show frame-relay map Serial1 (up): ip dlci 160(0xA0,0x2800), dynamic, broadcast,, status defined, active Serial1 (up): ip dlci 160(0xA0,0x2800), static, CISCO, status defined, active aton#ping Type escape sequence to abort Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 68/68/68 ms aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 64/67/80 ms 配 置 帧 中 继 子 接 口 帧 中 继 子 接 口 提 供 了 一 种 机 制, 支 持 部 分 网 状 帧 中 继 网 络 多 数 协 议 假 设 在 逻 辑 网 络 的 及 物 性 ; 也 就 是 说, 如 果 A 站 能 与 B 站 通 话,B 站 能 与 C 站 通 话, 则 A 站 应 该 能 够 与 C 站 直 接 通 话 实 际 上 传 输 在 LAN 上 而 不 在 帧 中 继 网 络 上 进 行, 除 非 A 直 接 连 接 到 C 此 外, 部 分 网 状 网 络 不 支 持 某 些 协 议, 例 如 AppleTalk 透 明 桥 接 和 IPX, 因 为 它 们 需 要 " 水 平 分 割 " 在 这 些 网 络 中, 在 一 个 接 口 上 收 到 的 信 息 包 不 能 通 过 同 一 接 口 发 出, 即 使 信 息 包 在 不 同 的 虚 拟 电 路 上 接 收 和 传 输

11 配 置 帧 中 继 子 接 口 可 将 单 个 物 理 接 口 用 作 多 个 虚 拟 接 口 此 功 能 允 许 我 们 解 决 水 平 分 割 规 则 虚 拟 接 口 收 到 的 信 息 包 现 在 可 以 转 发 给 另 一 个 虚 拟 接 口, 即 使 它 们 配 置 在 同 一 个 物 理 接 口 子 接 口 通 过 将 部 分 网 状 帧 中 继 网 络 划 分 为 许 多 较 小 的 完 全 网 状 ( 或 点 对 点 ) 子 网, 为 帧 中 继 网 络 的 限 制 问 题 提 供 了 一 种 解 决 方 法 每 个 子 网 络 分 配 了 它 自 己 的 网 络 编 号, 并 且 协 议 看 起 来 好 象 可 以 通 过 独 立 接 口 达 到 ( 注 意, 点 到 点 子 接 口 可 能 没 有 分 配 IP 地 址, 以 降 低 编 址 的 负 担 ) 点 到 点 子 接 口 网 络 图 配 置 #show running-config Building configuration... Current configuration : 1338 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname enable password ww interface Ethernet0 ip address interface Serial0 no ip address interface Serial0.1 point-to-point ip address frame-relay interface-dlci 140 router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1234 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec

12 no service password-encryption hostname interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point ip address frame-relay interface-dlci 150 router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end 显 示 命 令 show frame-relay map show frame-relay pvc #show frame-relay map Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 193 output pkts 175 in bytes out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 50 out bcast bytes 3786 pvc create time 01:11:27, last time pvc status changed 00:42:32 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms #show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched

13 Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 74 output pkts 89 in bytes 7210 out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 24 out bcast bytes 4203 pvc create time 00:12:25, last time pvc status changed 00:12:25 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms 星 型 连 接 子 接 口 以 下 星 型 网 配 置 示 例 显 示 两 个 点 对 点 子 接 口 并 且 使 用 在 一 个 远 程 站 点 的 动 态 地 址 解 析 每 个 子 接 口 带 有 单 个 协 议 地 址 和 子 网 掩 码, 并 且 interface-dlci 命 令 将 子 接 口 与 一 个 指 定 的 数 据 链 路 连 接 标 识 符 (DLCI) 关 联 起 来 每 个 点 到 点 子 接 口 的 远 程 目 的 地 地 址 没 有 被 解 析, 因 为 它 们 是 点 到 点 接 口, 流 量 必 须 发 送 到 另 一 端 的 对 等 接 口 远 程 终 端 (Aton) 使 用 反 向 ARP 进 行 映 射, 中 心 相 应 地 回 复 子 接 口 的 IP 地 址 默 认 情 况 下, 因 为 帧 中 继 反 向 ARP 打 开 为 多 点 接 口, 这 发 生 网 络 图 配 置 Aton #show running-config Building configuration... version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial0 no ip address interface Serial0.1 point-to-point ip address frame-relay interface-dlci 140 interface Serial0.2 point-to-point ip address frame-relay interface-dlci 130 router igrp 2 network network

14 network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point ip address frame-relay interface-dlci 150 router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end Aton Aton#show running-config Building configuration... Current configuration: version 12.0 service timestamps debug uptime service timestamps log uptime hostname Aton interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 160 router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login

15 end 显 示 命 令 show frame-relay map show frame-relay pvc #show frame-relay map Serial0.2 (up): point-to-point dlci, dlci 130(0x82,0x2020), broadcast status defined, active Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 130, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.2 input pkts 11 output pkts 22 in bytes 1080 out bytes 5128 dropped pkts 0 in FECN pkts 0 out bcast pkts 17 out bcast bytes 4608 pvc create time 00:06:36, last time pvc status changed 00:06:36 DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 33 output pkts 28 in bytes 3967 out bytes 5445 dropped pkts 0 in FECN pkts 0 out bcast pkts 17 out bcast bytes 4608 pvc create time 00:06:38, last time pvc status changed 00:06:38 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms #show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 45 output pkts 48 in bytes 8632 out bytes 6661 dropped pkts 0 in FECN pkts 0 out bcast pkts 31 out bcast bytes 5573 pvc create time 00:12:16, last time pvc status changed 00:06:23

16 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms Aton Aton#show frame-relay map Serial1 (up): ip dlci 160(0xA0,0x2800), dynamic, broadcast,, status defined, active Aton#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 160, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1 input pkts 699 output pkts 634 in bytes out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 528 out bcast bytes pvc create time 05:46:14, last time pvc status changed 00:05:57 Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms 配 置 多 点 子 接 口 的 动 态 和 静 态 映 射 在 给 定 了 数 据 链 路 连 接 标 识 符 (DLCI) 的 情 况 下, 动 态 地 址 映 射 使 用 帧 中 继 逆 向 ARP, 以 请 求 实 现 特 殊 连 接 的 下 一 跳 协 议 地 址 反 向 ARP 请 求 的 回 应 被 输 入 到 路 由 器 或 接 入 服 务 器 上 的 地 址 到 DLCI 的 映 射 表 中 然 后 表 可 以 为 流 出 的 数 据 流 提 供 下 一 跳 协 议 地 址 或 DLCI 由 于 物 理 接 口 现 在 配 置 为 多 个 子 接 口, 您 必 须 提 供 一 些 信 息, 以 区 分 子 接 口 和 物 理 接 口, 将 特 定 子 接 口 与 特 定 DLCI 关 联 在 默 认 情 况 下, 所 有 支 持 协 议 都 能 使 用 反 向 ARP, 而 但 在 某 些 特 殊 协 议 DLCI 对 中 则 可 能 被 限 制 使 用 结 果 是, 您 可 以 把 动 态 映 射 用 于 某 些 协 议, 把 静 态 映 射 用 于 相 同 DLCI 上 的 其 他 协 议 如 果 您 知 道 连 接 的 另 一 端 不 支 持 协 议, 您 就 能 明 确 地 禁 用 协 议 DLCI 对 的 反 向 ARP 由 于 反 向 ARP 默 认 在 它 支 持 的 所 有 协 议 上 都 是 启 动 的, 因 此 不 需 要 使 用 其 他 命 令 在 子 接 口 上 配 置 动 态 地 址 映 射 静 态 映 射 连 接 对 指 定 的 DLCI 的 指 定 的 下 一 跳 地 址 协 议 地 址 静 态 映 射 取 消 对 反 向 ARP 请 求 的 需 要 ; 在 您 提 供 静 态 映 射 时, 特 定 DLCI 上 的 指 定 的 协 议 将 自 动 禁 用 反 向 ARP 如 果 路 由 器 在 另 一 端 完 全 不 支 持 反 向 ARP, 或 者 不 支 持 您 要 在 帧 中 继 上 使 用 的 特 定 协 议 的 反 向 ARP, 您 必 须 使 用 静 态 映 射 网 络 图 我 们 已 经 看 见 如 何 配 置 Cisco 路 由 器 执 行 反 向 ARP 下 例 显 示 的 是 如 何 在 您 需 要 用 于 多 点 接 口 或 子 接 口 的 情 况 下 配 置 静 态 映 射 : 配 置 Aton Aton

17 Aton#show running-config Building configuration... Current configuration: version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption hostname Aton interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 multipoint ip address frame-relay map ip broadcast router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration...current configuration : 1652 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial0 ip address frame-relay map ip broadcast frame-relay map ip broadcast router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1162 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption

18 hostname interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 multipoint ip address frame-relay map ip broadcast router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end debug 和 show 命 令 show frame-relay map show frame-relay pvc Aton Aton#show frame-relay map Serial1.1 (up): ip dlci 160(0xA0,0x2800), static, broadcast, CISCO, status defined, active Aton#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 160, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 16 output pkts 9 in bytes 3342 out bytes 450 dropped pkts 0 in FECN pkts 0 out bcast pkts 9 out bcast bytes 450 pvc create time 00:10:02, last time pvc status changed 00:10:02 Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms #show frame-relay map Serial0 (up): ip dlci 140(0x8C,0x20C0), static, broadcast, CISCO, status defined, active Serial0 (up): ip dlci 130(0x82,0x2020), static, broadcast, CISCO, status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched

19 Unused DLCI = 130, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 9 output pkts 48 in bytes 434 out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 48 out bcast bytes pvc create time 00:36:25, last time pvc status changed 00:36:15 DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 17 output pkts 26 in bytes 1390 out bytes 4195 dropped pkts 0 in FECN pkts 0 out bcast pkts 16 out bcast bytes 3155 pvc create time 00:08:39, last time pvc status changed 00:08:39 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 #show frame-relay map Serial1.1 (up): ip dlci 150(0x96,0x2460), static, broadcast, CISCO, status defined, active #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 28 output pkts 19 in bytes 4753 out bytes 1490 dropped pkts 0 in FECN pkts 0 out bcast pkts 9 out bcast bytes 450 pvc create time 00:11:00, last time pvc status changed 00:11:00 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms 关 于 这 些 命 令 的 更 多 信 息, 请 参 阅 帧 中 继 命 令 配 置 IP 无 编 号 帧 中 继 如 果 您 没 有 IP 地 址 空 间 来 使 用 许 多 子 接 口, 您 可 以 在 每 个 子 接 口 上 使 用 未 编 号 的 IP 如 果 出 现 这 种 情 况, 您 需 要 使 用 静 态 路 由 或 动 态 路 由, 以 便 您 的 数 据 流 照 常 被 路 由, 并 且 您 必 须 使 用 点 到 点 子 接 口 网 络 图 下 面 的 示 例 说 明 此 :

20 配 置 #show running-config Building configuration... Current configuration : 1674 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial0 no ip address interface Serial0.1 point-to-point ip unnumbered Ethernet0 frame-relay interface-dlci 140 router igrp 2 network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1188 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point ip unnumbered Ethernet0 frame-relay interface-dlci 150 router igrp 2 network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end

21 显 示 命 令 show frame-relay map show frame-relay pvc #show frame-relay map Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 23 output pkts 24 in bytes 3391 out bytes 4952 dropped pkts 0 in FECN pkts 0 out bcast pkts 14 out bcast bytes 3912 pvc create time 00:04:47, last time pvc status changed 00:04:47 #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, Ethernet /8 is variably subnetted, 2 subnets, 2 masks I /8 [100/8576] via , 00:01:11, Serial0.1 I /32 [100/8576] via , 00:01:11, Serial0.1 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms #show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 24 output pkts 52 in bytes 4952 out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 41 out bcast bytes 9788 pvc create time 00:10:54, last time pvc status changed 00:03:51

22 #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /8 is variably subnetted, 2 subnets, 2 masks I /8 [100/8576] via , 00:00:18, Serial1.1 I /32 [100/8576] via , 00:00:18, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/120/436 ms 配 置 帧 中 继 备 份 ISDN 上 的 帧 中 继 备 份 使 用 ISDN, 您 可 以 希 望 到 备 用 帧 中 继 电 路 实 现 的 方 式 有 几 种 第 一 个, 也 很 可 能 是 最 佳 一 个, 使 用 浮 动 静 态 路 由, 将 流 量 路 由 到 基 本 速 率 接 口 (BRI) IP 地 址, 并 使 用 适 当 的 路 由 度 量 指 标 您 也 可 以 在 主 要 接 口 上 或 根 据 每 个 数 据 链 接 的 连 接 标 识 符 (DLCI) 使 用 备 份 接 口 对 于 备 份 主 要 接 口, 它 的 作 用 可 能 不 大, 因 为 您 可 能 丢 失 永 久 虚 拟 电 路 (PVC), 而 主 要 接 口 不 会 断 开 切 记, 协 议 用 本 地 帧 中 继 交 换 机 交 换, 不 是 远 程 路 由 器 配 置 路 由 器 1 路 由 器 2 路 由 器 1 ROUTER1# hostname ROUTER1 username ROUTER2 password same isdn switch-type basic-dms100 interface Ethernet 0 ip address interface serial 0 ip address encapsulation FRAME-RELAY interface BRI0 description Backup ISDN for frame-relay ip address encapsulation PPP dialer idle-timeout 240 dialer wait-for-carrier-time 60 dialer map IP name ROUTER2 broadcast ppp authentication chap dialer-group 1 isdn spid isdn spid router igrp 1 network

23 ip route Floating static route. access-list 101 deny igrp access-list 101 permit ip dialer-list 1 LIST 101 路 由 器 2 ROUTER2# hostname ROUTER2 username ROUTER1 password same isdn switch-type basic-dms100 interface Ethernet 0 ip address interface Serial 0 ip address encapsulation FRAME-RELAY interface BRI0 description ISDN backup interface for frame-relay ip address encapsulation PPP dialer idle-timeout 240 dialer map IP name ROUTER1 broadcast ppp authentication chap pulse-time 1 dialer-group 1 isdn spid isdn spid router igrp 1 network ip route Floating static route. access-list 101 deny igrp access-list 101 permit ip dialer-list 1 LIST 101 显 示 命 令 要 验 证, 如 果 ISDN 工 作, 请 使 用 以 下 调 试 指 令 在 发 出 debug 命 令 之 前, 请 参 阅 有 关 Debug 命 令 的 重 要 信 息 debug isdn q931 debug ppp neg debug ppp auth 设 法 由 主 叫 方 做 ISDN 呼 叫 到 中 心 端, 不 用 备 份 命 令 如 果 这 是 成 功 的, 请 添 加 备 份 命 令 到 主 叫 方 注 意 : 要 测 试 备 份, 请 不 要 在 串 行 接 口 使 用 shutdown 命 令, 但 可 以 从 串 联 线 拔 出 电 缆, 模 拟 真 正 串 联 线 问 题 配 置 每 个 DCLI 备 份 我 们 现 在 假 设 是 中 心 端, 是 与 中 心 端 () 建 立 连 接 的 端 注 意 您 只 能 将 backup 命 令 添 加 到 呼 叫 中 心 端 上 注 意 : 子 接 口 不 支 持 备 份 负 载 因 为 我 们 不 跟 踪 在 子 接 口 的 数 据 流 级 别, 负 载 没 有 计 算 网 络 图

24 配 置 #show running-config Building configuration... Current configuration : 1438 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname username password 0 cisco isdn switch-type basic-net3 interface Ethernet0 ip address interface Serial0 no ip address interface Serial0.1 point-to-point ip address frame-relay interface-dlci 140 interface BRI0 ip address encapsulation ppp dialer map ip name broadcast dialer-group 1 isdn switch-type basic-net3 no peer default ip address no cdp enable ppp authentication chap router igrp 2 network network network ip classless ip route access-list 101 deny igrp any any access-list 101 permit ip any any dialer-list 1 protocol ip list 101 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end

25 #show running-config Building configuration... Current configuration : 1245 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname username password 0 cisco isdn switch-type basic-net3 interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point backup delay 5 10 backup interface BRI0 ip address frame-relay interface-dlci 150 interface BRI0 ip address encapsulation ppp dialer map ip name broadcast 6106 dialer-group 1 isdn switch-type basic-net3 ppp authentication chap router igrp 2 network network network ip route access-list 101 deny igrp any any access-list 101 permit ip any any dialer-list 1 protocol ip list 101 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end 显 示 命 令 show frame-relay map show ip route show isdn history show isdn status show interface bri 0 show isdn active

26 #show frame-relay map Serial0.2 (up): point-to-point dlci, dlci 130(0x82,0x2020), broadcast status defined, active Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 2 subnets C is directly connected, Serial0.2 C is directly connected, BRI /24 is subnetted, 1 subnets C is directly connected, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet /8 is variably subnetted, 2 subnets, 2 masks I /8 [100/8576] via , 00:00:00, Serial0.1 S /24 [250/0] via I /8 [100/8576] via , 00:00:37, Serial0.2 # *Mar 1 00:59:12.527: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up *Mar 1 00:59:13.983: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up *Mar 1 00:59:18.547: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 6105 #show isdn history ISDN CALL HISTORY Call History contains all active calls, and a maximum of 100 inactive calls. Inactive call data will be retained for a maximum of 15 minutes Call Calling Called Remote Seconds Seconds Seconds Charges Type Number Number Name Used Left Idle Units/Currency In # *Mar 1 01:01:14.547: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 6105, call lasted 122 seconds *Mar 1 01:01:14.663: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:01:15.663: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down #show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set

27 I /8 [100/10476] via , 00:00:55, Serial /24 is subnetted, 1 subnets C is directly connected, Serial /8 is variably subnetted, 2 subnets, 2 masks S /24 [250/0] via I /8 [100/8576] via , 00:00:55, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 I /8 [100/10576] via , 00:00:55, Serial1.1 串 行 线 路 断 开 # *Mar 1 01:23:50.531: %LINK-3-UPDOWN: Interface Serial1, changed state to down *Mar 1 01:23:51.531: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down *Mar 1 01:23:53.775: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:23:53.791: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down *Mar 1 01:23:53.827: %LINK-3-UPDOWN: Interface BRI0, changed state to up *Mar 1 01:23:57.931: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF,IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, BRI /24 is subnetted, 1 subnets S [250/0] via /24 is subnetted, 1 subnets C is directly connected, Ethernet0 #show isdn status Global ISDN Switchtype = basic-net3 ISDN BRI0 interface dsl 0, interface ISDN Switchtype = basic-net3 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x Total Allocated ISDN CCBs = 0 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: *Mar 1 01:25:47.383: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up Success rate is 80 percent (4/5), round-trip min/avg/max = 36/36/36 ms # *Mar 1 01:25:48.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up # *Mar 1 01:25:53.407: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 6106 #show isdn status Global ISDN Switchtype = basic-net3 ISDN BRI0 interface dsl 0, interface ISDN Switchtype = basic-net3 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 1 Active Layer 3 Call(s) CCB:callid=8003, sapi=0, ces=1, B-chan=1, calltype=data Active dsl 0 CCBs = 1 The Free Channel Mask: 0x

28 Total Allocated ISDN CCBs = 1 #show isdn active ISDN ACTIVE CALLS Call Calling Called Remote Seconds Seconds Seconds Charges Type Number Number Name Used Left Idle Units/Currency Out # *Mar 1 01:27:49.027: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 6106, call lasted 121 seconds *Mar 1 01:27:49.131: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:27:50.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down *Mar 1 01:28:09.215: %LINK-3-UPDOWN: Interface Serial1, changed state to up *Mar 1 01:28:10.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up *Mar 1 01:28:30.043: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 64 changed to down *Mar 1 01:28:30.047: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to down *Mar 1 01:28:30.371: %LINK-5-CHANGED: Interface BRI0, changed state to standby mode *Mar 1 01:28:30.387: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:28:30.403: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down # 串 行 连 接 再 回 到 #show isdn status Global ISDN Switchtype = basic-net3 ISDN BRI0 interface dsl 0, interface ISDN Switchtype = basic-net3 Layer 1 Status: DEACTIVATED Layer 2 Status: Layer 2 NOT Activated Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x Total Allocated ISDN CCBs = 0 #show interface bri 0 BRI0 is standby mode, line protocol is down Hardware is BRI Internet address is /24 MTU 1500 bytes, BW 64 Kbit, DLY usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set Last input 00:01:00, output 00:01:00, output hang never Last clearing of "show interface" counters 01:28:16 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/16 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 128 packets input, 601 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 132 packets output, 687 bytes, 0 underruns 0 output errors, 0 collisions, 10 interface resets 0 output buffer failures, 0 output buffers swapped out 14 carrier transitions #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms 带 有 拨 号 程 序 配 置 文 件 的 星 型 网 这 是 星 型 网 的 示 例 每 个 DLCI 备 份 配 置 分 支 路 由 器 呼 叫 中 心 路 由 器 您 可 以 看 到, 我 们 在 中 心 端 的 拨 号 池 上 使 用 max-link 选 项, 每 端 只 允 许 一 条 B 信 道

29 注 意 : 子 接 口 不 支 持 备 份 负 载 因 为 我 们 不 跟 踪 在 子 接 口 的 数 据 流 级 别, 负 载 没 有 计 算 网 络 图 配 置 Aton Aton#show running-config Building configuration... Aton Current configuration: version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption hostname Aton username password 0 cisco isdn switch-type basic-net3 interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point ip address backup delay 5 10 backup interface BRI0 frame-relay interface-dlci 160 interface BRI0 ip address encapsulation ppp no ip route-cache no ip mroute-cache dialer map ip name broadcast 6106 dialer-group 1 isdn switch-type basic-net3 ppp authentication chap router igrp 2 network network network ip route access-list 101 deny igrp any any access-list 101 permit ip any any

30 dialer-list 1 protocol ip list 101 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1887 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname username password 0 cisco username Aton password 0 cisco isdn switch-type basic-net3 interface Ethernet0 ip address interface Serial0 no ip address interface Serial0.1 point-to-point ip address frame-relay interface-dlci 140 interface Serial0.2 point-to-point ip address frame-relay interface-dlci 130 interface BRI0 no ip address encapsulation ppp no ip route-cache no ip mroute-cache dialer pool-member 2 max-link 1 dialer pool-member 1 max-link 1 isdn switch-type basic-net3 no peer default ip address no cdp enable ppp authentication chap interface Dialer1 ip address encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer remote-name dialer-group 1 ppp authentication chap interface Dialer2 ip address encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 2 dialer remote-name Aton dialer-group 1 ppp authentication chap router igrp 2 network network network network

31 network access-list 101 deny igrp any any access-list 101 permit ip any any dialer-list 1 protocol ip list 101 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1267 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname username password 0 cisco isdn switch-type basic-net3 interface Ethernet0 ip address interface Serial1 no ip address interface Serial1.1 point-to-point backup delay 5 10 backup interface BRI0 ip address frame-relay interface-dlci 150 interface BRI0 ip address encapsulation ppp dialer map ip name broadcast 6106 dialer-group 1 isdn switch-type basic-net3 ppp authentication chap router igrp 2 network network network ip route access-list 101 deny igrp any any access-list 101 permit ip any any dialer-list 1 protocol ip list 101 line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end 显 示 命 令 show frame-relay map

32 show ip route show frame map show frame-relay pvc Aton Aton#show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 160(0xA0,0x2800), broadcast status defined, active Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms Aton#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR, P - periodic downloaded static route T - traffic engineered route Gateway of last resort is not set I /16 [100/182571] via , Serial /24 is subnetted, 1 subnets C is directly connected, Serial1.1 I /8 [100/10476] via , Serial1.1 I /16 [100/182571] via , Serial /8 is variably subnetted, 2 subnets, 2 masks S /24 [250/0] via I /8 [100/8576] via , Serial1.1 I /8 [100/10576] via , Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 Aton# Serial1 断 开 Aton# 01:16:33: %LINK-3-UPDOWN: Interface Serial1, changed state to down 01:16:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down 01:16:37: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 01:16:37: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down 01:16:37: %LINK-3-UPDOWN: Interface BRI0, changed state to up 01:16:41: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up Aton#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR, P - periodic downloaded static route T - traffic engineered route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, BRI /24 is subnetted, 1 subnets S [250/0] via /24 is subnetted, 1 subnets C is directly connected, Ethernet0 Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: 01:21:33: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up. Success rate is 80 percent (4/5), round-trip min/avg/max = 36/36/36 ms Aton# 01:21:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up 01:21:39: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 6106

33 Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/123/296 ms Aton# Serial1 再 变 得 激 活 Aton# 01:24:02: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 6106, call lasted 149 seconds 01:24:02: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 01:24:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down Aton#show frame map Serial1.1 (down): point-to-point dlci, dlci 160(0xA0,0x2800), broadcast status deleted Aton# 01:26:35: %LINK-3-UPDOWN: Interface Serial1, changed state to up 01:26:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up 01:26:56: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 64 changed to down 01:26:56: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to down 01:26:56: %LINK-5-CHANGED: Interface BRI0, changed state to standby mode 01:26:56: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 01:26:56: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down Aton#show frame map Serial1.1 (up): point-to-point dlci, dlci 160(0xA0,0x2800), broadcast status defined, active Aton#ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms Aton#ping Aton#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 160, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 60 output pkts 69 in bytes 9694 out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 44 out bcast bytes 7565 pvc create time 01:28:35, last time pvc status changed 00:02:19 #show frame-relay map Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active Serial0.2 (up): point-to-point dlci, dlci 130(0x82,0x2020), broadcast status defined, active #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds:

34 Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, Dialer /24 is subnetted, 1 subnets C is directly connected, Serial /24 is subnetted, 1 subnets C is directly connected, Serial /24 is subnetted, 1 subnets C is directly connected, Dialer /24 is subnetted, 1 subnets C is directly connected, Ethernet0 I /8 [100/8576] via , 00:00:55, Serial0.1 I /8 [100/8576] via , 00:00:35, Serial0.2 从 主 叫 方 的 两 串 行 线 路 断 开 # *Mar 1 01:21:30.171: %LINK-3-UPDOWN: Interface BRI0:1, changed state toup *Mar 1 01:21:30.627: %DIALER-6-BIND: Interface BR0:1 bound to profile Di2 *Mar 1 01:21:31.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up *Mar 1 01:21:36.191: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 6104 Aton *Mar 1 01:21:40.923: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up *Mar 1 01:21:41.359: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1 *Mar 1 01:21:42.383: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to up *Mar 1 01:21:46.943: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 6105 *Mar 1 01:23:59.819: %DIALER-6-UNBIND: Interface BR0:1 unbound from profile Di2 *Mar 1 01:23:59.831: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 6104 Aton, call lasted 149 seconds *Mar 1 01:23:59.927: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:24:00.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down *Mar 1 01:24:03.015: %DIALER-6-UNBIND: Interface BR0:2 unbound from profile Di1 *Mar 1 01:24:03.023: %ISDN-6-DISCONNECT: Interface BRI0:2 disconnected from 6105, call lasted 142 seconds *Mar 1 01:24:03.107: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down *Mar 1 01:24:04.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to down #show frame map Serial0.1 (down): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, inactive Serial0.2 (down): point-to-point dlci, dlci 130(0x82,0x2020), broadcast status defined, inactive # 两 串 行 线 路 再 是 可 用 的 #show frame pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 130, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.2 input pkts 54 output pkts 61 in bytes 7014 out bytes 9975 dropped pkts 3 in FECN pkts 0 out bcast pkts 40 out bcast bytes 7803 pvc create time 01:28:14, last time pvc status changed 00:02:38

35 DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 56 output pkts 60 in bytes 7604 out bytes dropped pkts 2 in FECN pkts 0 out bcast pkts 39 out bcast bytes 7928 pvc create time 01:28:15, last time pvc status changed 00:02:29 #show frame-relay map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set I /16 [100/182571] via , 00:00:41, Serial1.1 I /8 [100/10476] via , 00:00:41, Serial /24 is subnetted, 1 subnets C is directly connected, Serial1.1 I /16 [100/182571] via , 00:00:41, Serial /8 is variably subnetted, 2 subnets, 2 masks S /24 [250/0] via I /8 [100/8576] via , 00:00:41, Serial /24 is subnetted, 1 subnets C is directly connected, Ethernet0 I /8 [100/10576] via , 00:00:42, Serial1.1 # Serial1 断 开 # *Mar 1 01:16:08.287: %LINK-3-UPDOWN: Interface Serial1, changed state to down *Mar 1 01:16:09.287: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down *Mar 1 01:16:11.803: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:16:11.819: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down *Mar 1 01:16:11.855: %LINK-3-UPDOWN: Interface BRI0, changed state to up *Mar 1 01:16:15.967: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up #show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, BRI /24 is subnetted, 1 subnets S [250/0] via /24 is subnetted, 1 subnets C is directly connected, Ethernet0 #ping

36 Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: *Mar 1 01:21:38.967: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up. Success rate is 80 percent (4/5), round-trip min/avg/max = 36/36/36 ms # *Mar 1 01:21:40.063: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up *Mar 1 01:21:44.991: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 6106 #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms # Serial1 再 变 得 激 活 # *Mar 1 01:26:40.579: %LINK-3-UPDOWN: Interface Serial1, changed state to up *Mar 1 01:26:41.579: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up *Mar 1 01:27:01.051: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 64 changed to down *Mar 1 01:27:01.055: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to down *Mar 1 01:27:01.363: %LINK-5-CHANGED: Interface BRI0, changed state to standby mode *Mar 1 01:27:01.379: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down *Mar 1 01:27:01.395: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down #show frame map Serial1.1 (up): point-to-point dlci, dlci 150(0x96,0x2460), broadcast status defined, active #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 36/116/432 ms #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1.1 input pkts 58 output pkts 66 in bytes 9727 out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 46 out bcast bytes 7942 pvc create time 01:27:37, last time pvc status changed 00:01:59 配 置 帧 中 继 交 换 帧 中 继 交 换 是 根 据 数 据 链 路 连 接 标 识 符 (DLCI) 的 交 换 信 息 包 方 法 我 们 在 此 能 查 找 作 为 MAC 控 制 (MAC) 地 址 的 帧 中 继 等 同 您 通 过 配 置 您 的 Cisco 路 由 器 或 接 入 服 务 器 执 行 交 换 到 帧 中 继 网 络 有 两 部 分 对 帧 中 继 网 络 : 帧 中 继 数 据 终 端 设 备 (DTE) - 路 由 器 或 接 入 服 务 器 帧 中 继 数 据 电 路 终 端 的 设 备 (DCE) 交 换 机 注 意 : 在 Cisco IOS 软 件 release 12.1(2)T 及 以 上 版 本, frame route 命 令 由 连 接 命 令 替 换 了 请 查 看 配 置 示 例 在 下 面 的 配 置 中, 我 们 使 用 路 由 器 美 国 作 为 帧 中 继 交 换 机 我 们 使 用 作 为 中 心 路 由 器 和 和 Aton 作 为 分 支 路 由 器 我 们 连 接 他 们 如 下 : 序 列 1 (s1) DTE 连 接 对 美 国 序 列 1/4 (s1/4) DCE serial0 (s0) DTE 连 接 对 美 国 序 列 1/5 (s1/5) DCE

37 网 络 图 Aton 序 列 1 (s1) DTE 连 接 对 美 国 序 列 3/4 (s3/4) DCE 本 文 根 据 以 下 配 置 : 配 置 Aton 美 国 #show running-config Building configuration... version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname interface Ethernet0 ip address interface Serial0 ip address frame-relay interface-dlci 130 frame-relay interface-dlci 140 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... Current configuration : 1499 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption

38 hostname interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 150 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end Aton Aton#show running-config Building configuration... Current configuration: version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption hostname Aton interface Ethernet0 ip address interface Serial1 ip address frame-relay interface-dlci 160 router rip network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end 美 国 america#show running-config Building configuration... Current configuration: service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname america frame-relay switching interface Serial1/4 description *** static DCE connection to s1

39 no ip address clockrate frame-relay intf-type dce frame-relay route 150 interface Serial1/5 140 interface Serial1/5 description *** static DCE connection to s0 spicy no ip address bandwidth tx-queue-limit 100 frame-relay intf-type dce frame-relay route 130 interface Serial3/4 160 frame-relay route 140 interface Serial1/4 150 transmitter-delay 10 interface Serial3/4 description *** static DCE connection to s1 Aton no ip mroute-cache clockrate frame-relay intf-type dce frame-relay route 160 interface Serial1/5 130 显 示 命 令 请 使 用 以 下 显 示 命 令 测 试 您 的 网 络 适 当 地 操 作 : show frame-relay map show frame-relay pvc 以 下 所 示 的 输 出 是 在 我 们 在 此 示 例 配 置 中 使 用 的 设 备 上 输 入 这 些 命 令 的 结 果 #show frame-relay map Serial0 (up): ip dlci 140(0x8C,0x20C0), dynamic, broadcast,, status defined, active Serial0 (up): ip dlci 130(0x82,0x2020), dynamic, broadcast,, status defined, active #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 130, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 32 output pkts 40 in bytes 3370 out bytes 3928 dropped pkts 0 in FECN pkts 0 out bcast pkts 30 out bcast bytes 2888 pvc create time 00:15:46, last time pvc status changed 00:10:42 DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 282 output pkts 291 in bytes out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 223 out bcast bytes pvc create time 02:28:36, last time pvc status changed 02:25:14 #show frame-relay map Serial1 (up): ip dlci 150(0x96,0x2460), dynamic, broadcast,, status defined, active #show frame-relay pvc

40 PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1 input pkts 311 output pkts 233 in bytes out bytes dropped pkts 0 in FECN pkts 0 out bcast pkts 162 out bcast bytes pvc create time 02:31:39, last time pvc status changed 02:25:14 Aton Aton#show frame-relay map Serial1 (up): ip dlci 160(0xA0,0x2800), dynamic, broadcast, status defined, active Aton#show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 160, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial input pkts 35 output pkts 32 in bytes 3758 out bytes 3366 dropped pkts 0 in FECN pkt 0 out bcast pkts 27 out bcast bytes 2846 pvc create time 00:10:53, last time pvc status changed 00:10:53 配 置 帧 中 继 DLCI 优 先 级 通 过 数 据 链 路 连 接 标 识 符 (DLCI) 优 先 级 排 列 很 多 不 同 的 业 务 类 型 能 够 放 置 在 独 立 的 DLCI 上, 以 便 帧 中 继 网 络 能 为 每 个 业 务 类 型 提 供 不 同 的 承 诺 信 息 速 率 它 可 以 与 自 定 义 排 队 或 优 先 级 排 队 结 合 使 用, 提 供 帧 中 继 网 络 的 接 入 链 路 的 带 宽 管 理 控 制 另 外, 一 些 帧 中 继 服 务 提 供 商 和 帧 中 继 交 换 机 ( 例 如 Stratacom 互 联 网 络 信 息 包 交 换 [IPX] IGX BPX 或 AXIS 交 换 机 ) 可 根 据 优 先 级 设 置, 在 帧 中 继 网 云 中 提 供 优 先 级 排 列 实 施 注 意 事 项 当 实 现 DLCI 优 先 级 划 分, 请 注 意 下 列 问 题 时 : 网 络 图 如 果 附 属 DLCI 断 开, 您 将 丢 失 定 向 到 该 队 列 的 数 据 流 如 果 您 丢 失 主 要 DLCI, 那 么 子 接 口 断 开 并 且 丢 失 所 有 数 据 流 为 了 使 用 此 设 置, 您 需 为 使 用 DLCI 优 先 级 划 分 的 一 端 提 供 四 个 DLCI 在 本 例 中, 我 们 配 置 优 先 级 队 列 的 如 下 : Ping 在 高 优 先 级 队 列 Telnet 在 优 先 级 队 列 文 件 传 输 协 议 (FTP) 在 normal-priority 队 列 其 他 IP 数 据 流 在 低 优 先 级 队 列 注 意 : 确 保 您 配 置 的 DLCI 与 优 先 级 列 表 匹 配, 或 者 系 统 不 能 使 用 正 确 队 列 配 置

41 #show running-config Building configuration... Current configuration : 1955 bytes version 12.1 service timestamps debug datetime msec service timestamps log datetime msec hostname interface Ethernet0 ip address interface Serial0 no ip address priority-group 1 interface Serial0.1 point-to-point ip address frame-relay priority-dlci-group frame-relay interface-dlci 140 router igrp 2 network network access-list 102 permit icmp any any priority-list 1 protocol ip high list 102 priority-list 1 protocol ip medium tcp telnet priority-list 1 protocol ip normal tcp ftp priority-list 1 protocol ip low line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end #show running-config Building configuration... version 12.1 service timestamps debug datetime msec service timestamps log datetime msec hostname interface Ethernet0 ip address interface Serial1 ip address router igrp 2 network network line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login end debug 和 show 命 令

42 请 使 用 以 下 显 示 和 调 试 指 令 测 试 您 的 网 络 适 当 地 操 作 在 发 出 debug 命 令 之 前, 请 参 阅 有 关 Debug 命 令 的 重 要 信 息 show frame-relay pvc show frame-relay map show queueing priority debug priority 以 下 所 示 的 输 出 是 在 我 们 在 此 示 例 配 置 中 使 用 的 设 备 上 输 入 这 些 命 令 的 结 果 #show frame-relay pvc PVC Statistics for interface Serial0 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 106 output pkts 15 in bytes 6801 out bytes 1560 dropped pkts 0 in FECN pkts 0 out bcast pkts 0 out bcast bytes 0 pvc create time 00:29:22, last time pvc status changed 00:20:37 Priority DLCI Group 1, DLCI 140 (HIGH), DLCI 180 (MEDIUM) DLCI 190 (NORMAL), DLCI 200 (LOW) DLCI = 180, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 0 output pkts 51 in bytes 0 out bytes 2434 dropped pkts 0 in FECN pkts 0 out bcast pkts 0 out bcast bytes 0 pvc create time 00:29:23, last time pvc status changed 00:14:48 DLCI = 190, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 0 output pkts 13 in bytes 0 out bytes 3653 dropped pkts 0 in FECN pkts 0 out bcast pkts 13 out bcast bytes 3653 pvc create time 00:29:23, last time pvc status changed 00:14:28 DLCI = 200, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1 input pkts 0 output pkts 42 in bytes 0 out bytes 2554 dropped pkts 0 in FECN pkts 0 out bcast pkts 10 out bcast bytes 500 pvc create time 00:29:24, last time pvc status changed 00:14:09 #show frame-relay map Serial0.1 (up): point-to-point dlci, dlci 140(0x8C,0x20C0), broadcast status defined, active Priority DLCI Group 1, DLCI 140 (HIGH), DLCI 180 (MEDIUM) DLCI 190 (NORMAL), DLCI 200 (LOW) #show queueing priority Current priority queue configuration: List Queue Args 1 high protocol ip list medium protocol ip tcp port telnet 1 normal protocol ip tcp port ftp 1 low protocol ip 要 验 证 优 先 级 队 列, 请 使 用 debug priority 命 令 #debug priority Priority output queueing debugging is on #ping

43 Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms # *Mar 1 00:32:30.391: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.395: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.399: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:32:30.439: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.443: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.447: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:32:30.487: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.491: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.495: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:32:30.535: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.539: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.543: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:32:30.583: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.587: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:32:30.587: PQ: Serial0 output (Pk size/q 104/0)# #telnet Trying Open User Access Verification Password: *Mar 1 00:32:59.447: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.451: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.451: PQ: Serial0 output (Pk size/q 48/1) *Mar 1 00:32:59.475: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.479: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.483: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:32:59.487: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.487: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.491: PQ: Serial0 output (Pk size/q 53/1) *Mar 1 00:32:59.495: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.499: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.499: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:32:59.511: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.511: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.515: PQ: Serial0 output (Pk size/q 47/1) *Mar 1 00:32:59.519: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.519: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.523: PQ: Serial0 output (Pk size/q 47/1) *Mar 1 00:32:59.527: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.527: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.531: PQ: Serial0 output (Pk size/q 53/1) *Mar 1 00:32:59.539: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.543: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.547: PQ: Serial0 output (Pk size/q 47/1) *Mar 1 00:32:59.751: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.755: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:32:59.755: PQ: Serial0 output (Pk size/q 44/1) Password: 其 他 IP 数 据 流 通 过 低 队 列 # *Mar 1 00:53:57.079: PQ: Serial0 output (Pk size/q 13/0) *Mar 1 00:53:58.851: PQ: Serial0: ip -> low *Mar 1 00:53:58.907: PQ: Serial0: ip -> low *Mar 1 00:53:58.907: PQ: Serial0 output (Pk size/q 36/3) *Mar 1 00:53:59.459: PQ: Serial0: ip -> low *Mar 1 00:53:59.463: PQ: Serial0: ip -> low *Mar 1 00:53:59.463: PQ: Serial0 output (Pk size/q 50/3) # #show frame-relay pvc PVC Statistics for interface Serial1 (Frame Relay DTE) Active Inactive Deleted Static Local Switched Unused DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1

44 input pkts 134 output pkts 119 in bytes out bytes 7801 dropped pkts 0 in FECN pkts 0 out bcast pkts 18 out bcast bytes 1260 pvc create time 00:21:15, last time pvc status changed 00:21:15 #show frame-relay map Serial1 (up): ip dlci 150(0x96,0x2460), dynamic, broadcast, status defined, active #ping Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 Here is the debug output shown on when you use the command above to ping to from. # *Mar 1 00:33:26.755: PQ: Serial0 output (Pk size/q 13/0) *Mar 1 00:33:28.535: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.539: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.543: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:33:28.583: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.587: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.587: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:33:28.631: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.635: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.635: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:33:28.679: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.683: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.683: PQ: Serial0 output (Pk size/q 104/0) *Mar 1 00:33:28.723: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.727: PQ: Serial0: ip (s= , d= ) ->high *Mar 1 00:33:28.731: PQ: Serial0 output (Pk size/q 104/0) #telnet Trying Open User Access Verification Password: >exit [Connection to closed by foreign host] # 当 您 使 用 调 试 命 令 从 远 程 登 录 到 时, 这 便 是 上 显 示 的 调 试 输 出 # *Mar 1 00:33:54.499: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.499: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.503: PQ: Serial0 output (Pk size/q 48/1) *Mar 1 00:33:54.527: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.531: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.531: PQ: Serial0 output (Pk size/q 56/1) *Mar 1 00:33:54.547: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.551: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.555: PQ: Serial0 output (Pk size/q 86/1) *Mar 1 00:33:54.559: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.563: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.563: PQ: Serial0 output (Pk size/q 47/1) *Mar 1 00:33:54.571: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.575: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.575: PQ: Serial0 output (Pk size/q 47/1) *Mar 1 00:33:54.779: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.783: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:54.783: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:33:56.755: PQ: Serial0 output (Pk size/q 13/0) *Mar 1 00:33:57.143: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.143: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.147: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:33:57.447: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.447: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.451: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:33:57.899: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.899: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:57.903: PQ: Serial0 output (Pk size/q 53/1) *Mar 1 00:33:59.491: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:59.495: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:59.495: PQ: Serial0 output (Pk size/q 45/1) *Mar 1 00:33:59.711: PQ: Serial0: ip (tcp 23) -> medium

45 *Mar 1 00:33:59.715: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:59.715: PQ: Serial0 output (Pk size/q 45/1) *Mar 1 00:33:59.951: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:59.951: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:33:59.955: PQ: Serial0 output (Pk size/q 45/1) *Mar 1 00:34:00.123: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.123: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.127: PQ: Serial0 output (Pk size/q 45/1) *Mar 1 00:34:00.327: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.327: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.331: PQ: Serial0 output (Pk size/q 46/1) *Mar 1 00:34:00.495: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.499: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.499: PQ: Serial0 output (Pk size/q 44/1) *Mar 1 00:34:00.543: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.543: PQ: Serial0: ip (tcp 23) -> medium *Mar 1 00:34:00.547: PQ: Serial0 output (Pk size/q 44/1) 帧 中 继 广 播 队 列 广 播 队 列 是 在 中 型 到 大 型 IP 或 IPX 网 络 中 使 用 的 一 种 主 要 功 能, 在 这 些 网 络 中, 路 由 和 服 务 接 入 点 (SAP) 广 播 必 须 在 帧 中 继 网 络 上 传 送 广 播 队 列 在 正 常 接 口 队 列 中 进 行 独 立 管 理, 有 它 自 己 的 缓 冲 区 可 配 置 大 小 和 服 务 速 率 此 广 播 队 列 没 有 使 用 桥 接 生 成 树 更 新 (BPDU) 由 于 时 钟 灵 敏 度 这 些 数 据 包 将 流 经 正 常 队 列 interface 命 令 启 用 广 播 队 列 跟 随 : 帧 中 继 广 播 队 列 大 小 字 节 速 率 信 息 包 费 率 广 播 队 列 被 指 定 最 大 传 输 速 率 ( 吞 吐 量 ) 限 额, 该 限 额 按 每 秒 字 节 数 和 每 秒 信 息 包 数 测 量 队 列 被 服 务 保 证 提 供 仅 此 最 大 数 量 传 输 速 率 低 于 配 置 的 最 大 速 率 时, 广 播 队 列 会 有 优 先 级, 并 且 保 证 有 最 小 带 宽 分 配 两 个 传 输 速 率 限 额 打 算 避 免 充 斥 接 口 与 广 播 实 际 限 制 在 所 有 秒 钟 是 达 到 的 第 一 个 速 率 限 制 给 传 输 速 率 限 制, 另 外 的 缓 冲 要 求 存 储 广 播 包 广 播 队 列 是 可 配 置 存 储 很 大 数 量 的 广 播 包 应 该 设 置 队 列 大 小 避 免 广 播 路 由 更 新 数 据 包 损 耗 确 切 大 小 取 决 于 正 在 使 用 的 协 议 和 每 次 更 新 所 需 的 信 息 包 数 量 为 安 全 起 见, 队 列 大 小 的 设 置 应 该 确 保 来 自 每 个 协 议 的 每 个 数 据 链 路 连 接 标 识 符 (DLCI) 的 完 整 路 由 更 新 能 够 存 储 通 常, 请 从 每 个 DLCI 20 数 据 包 开 始 比 特 率 比 两 个 应 该 是 较 少 的 下 列 : N/4 乘 以 最 低 远 程 访 问 速 率 ( 以 字 节 / 秒 为 单 位 ), 其 中 的 N 是 广 播 必 须 复 制 到 的 DLCI 的 数 量 1/4 本 地 访 问 存 取 速 率 ( 测 量 在 字 节 每 秒 ) 如 果 比 特 率 适 当 地, 设 置 数 据 包 速 率 不 是 关 键 一 般 来 说, 应 该 设 置 数 据 包 速 率 假 设 250-byte 数 据 包 默 认 串 行 接 口 为 64 个 队 列 大 小 每 秒 256,000 个 字 节 (2,048,000 bps) 和 36 pps 高 速 串 行 接 口 (HSSI) 的 默 认 值 为 256 个 队 列 大 小 1,024,000 字 节 / 秒 (8,192,000 bps) 和 144 pps 流 量 整 形 流 量 整 形 使 用 呼 叫 令 牌 桶 过 滤 器 的 一 个 速 率 控 制 控 制 机 制 此 令 牌 桶 过 滤 器 设 置 如 下 : 超 额 突 发 加 上 承 诺 突 发 量 (Bc+Be) = 虚 拟 电 路 的 最 大 速 度 超 出 最 大 速 度 的 数 据 流 在 流 量 整 形 队 列 中 缓 冲, 该 队 列 的 大 小 与 加 权 公 平 排 队 (WFQ) 相 等 令 牌 桶 过 滤 器 不 过 滤 数 据 流, 但 控 制 出 局 接 口 上 的 数 据 流 发 送 速 率 关 于 令 牌 桶 过 滤 器 的 更 多 信 息, 请 参 阅 监 管 与 整 形 概 述 本 文 提 供 通 用 流 量 整 形 和 帧 中 继 流 量 整 形 概 述 流 量 整 形 参 数 我 们 能 使 用 以 下 流 量 整 形 参 数 : CIR = 承 诺 信 息 速 率 (= 平 均 时 间 ) EIR = 过 大 信 息 速 率 TB = 令 牌 桶 (= Bc+Be) BC = 承 诺 突 发 流 量 大 小 (= 持 续 的 突 发 流 量 大 小 ) 是 = 超 额 突 发 大 小 DE = 丢 弃 资 格 Tc = 测 量 间 隔 AR = 与 物 理 接 口 速 率 对 应 的 接 入 速 率 ( 如 果 您 使 用 T1,AR 约 为 1.5 Mbps) 请 较 详 细 地 查 看 其 中 一 些 参 数 : 存 取 速 率 (AR) 终 端 站 到 网 络 的 最 高 传 输 速 度 ( 比 特 / 秒 ) 受 到 用 户 网 络 接 口 的 接 入 速 率 的 限 制 客 户 网 络 连 接 的 线 路 速 度 限 制 接 入 速 率 您 在 您 的 订 阅 能 设 立 此 到 服 务 提 供 商 承 诺 突 发 流 量 大 小 (BC)

46 您 能 提 供 到 网 络 的 最 大 承 诺 量 数 据 定 义 作 为 BC Bc 是 保 证 网 络 正 常 情 况 下 交 付 的 数 据 量 的 测 量 在 承 诺 速 率 Tc 期 间, 它 被 测 量 超 额 突 发 大 小 (Be) 仍 被 帧 中 继 交 换 机 接 受 但 被 标 志 为 符 合 丢 弃 条 件 (DE) 的 非 承 诺 位 (CIR 以 外 ) 的 数 量 令 牌 桶 是 虚 拟 缓 冲 区 它 包 含 一 定 数 量 的 令 牌, 启 用 您 发 送 有 限 的 数 据 每 个 时 间 间 隔 令 牌 桶 充 满 BC 位 每 个 Tc 桶 的 最 大 大 小 是 Bc+Be 如 果 Be 非 常 大, 在 T0 时 段, 令 牌 桶 填 满 了 BC+Be 令 牌, 则 您 能 够 以 接 入 速 率 发 送 BC+Be 位 这 不 是 通 过 TC 而 是 通 过 发 送 Be 的 时 间 限 制 的 这 是 接 入 速 率 的 功 能 承 诺 信 息 速 率 (CIR) CIR 是 网 络 承 诺 在 通 常 情 况 下 传 输 的 允 许 数 据 流 量 速 率 在 时 间 被 平 均 Tc 的 增 量 CIR 也 指 最 低 的 可 接 受 吞 吐 量 Bc 和 Be 以 位 为 单 位 Tc 以 秒 为 单 位 接 入 速 率 和 CIR 以 比 特 / 秒 为 单 位 BC, 是, Tc 和 CIR 每 数 据 链 路 连 接 标 识 符 (DLCI) 定 义 由 于 此, 令 牌 桶 过 滤 器 控 制 速 率 每 个 DLCI 接 入 速 率 每 个 用 户 网 络 接 口 是 有 效 对 于 Bc, Be 及 CIR 流 入 和 流 出 的 值 可 以 是 著 名 的 如 果 连 接 是 对 称 的, 在 两 个 方 向 的 值 是 相 同 的 对 于 永 久 虚 电 路, 我 们 定 义 了 流 入 和 流 出 的 Bc, Be 及 CIR 在 订 阅 时 间 高 峰 = DLCI 的 最 大 速 度 那 的 带 宽 特 定 DLCI Tc = Bc/CIR 高 峰 = CIR + Be/Tc = CIR (1 + Be/Bc) 如 果 Tc 是 一 秒 钟 然 后 : 高 峰 = CIR + 是 = Bc+Be EIR = 是 在 我 们 的 示 例 中, 路 由 器 根 据 网 络 中 的 拥 塞 情 况, 选 择 使 用 48 Kbps 还 是 32 Kbps 的 速 率 发 送 数 据 流 网 络 可 能 在 BC 上 用 DE 标 记 帧, 但 是 仍 有 大 量 空 闲 容 量 可 以 用 来 传 输 帧 反 向 也 是 可 能 的 : 他 们 能 立 即 限 制 了 产 能, 丢 弃 额 外 的 帧 网 络 可 能 在 Bc+Be 上 的 帧 标 记 DE, 可 能 传 输 这 个 帧, 或 者 根 据 国 际 电 信 联 盟 电 信 标 准 化 部 门 规 范 ITU-T I.370 丢 弃 它 流 量 整 形 抑 制 根 据 从 交 换 网 络 的 后 向 显 式 拥 塞 通 知 (BECN) 标 记 信 息 包 的 流 量 如 果 您 收 到 50% 的 BECN, 路 由 器 将 把 特 定 DLCI 减 少 到 当 前 传 输 带 宽 的 八 分 之 一 示 例 已 发 送 速 度 是 42 Kb 路 由 器 将 速 度 降 低 到 42-42/8, 为 千 字 节 如 果 更 改 后 拥 塞 减 少, 路 由 器 将 进 一 步 减 少 流 量, 从 而 使 当 前 传 输 带 宽 下 降 至 原 来 的 八 分 之 一 减 少 流 量, 直 到 达 到 配 置 的 CIR 值 然 而, 当 我 们 仍 然 能 看 见 BECN 时, 速 度 可 以 降 至 CIR 以 下 您 能 指 定 一 底 下 限 制, 例 如 CIR/2 当 从 网 络 中 收 到 的 所 有 帧, 在 给 定 的 时 间 间 隔 中 不 再 有 BECN 位 时, 网 络 便 不 再 拥 塞 200 毫 秒 是 此 间 隔 的 默 认 值 一 般 流 量 整 形 通 用 流 量 整 形 功 能 是 一 种 独 立 于 媒 体 和 封 装 的 流 量 整 形 工 具, 当 网 云 链 路 和 接 受 终 端 路 由 器 发 生 拥 塞 时, 它 可 以 减 少 出 局 流 量 我 们 在 接 口 或 子 接 口 能 设 置 它 在 路 由 器 内 通 用 流 量 整 形 在 以 下 情 况 下 是 有 用 的 :

47 当 您 的 网 络 拓 扑 由 中 心 站 点 的 高 速 连 接 (T1 线 路 速 度 ) 分 支 机 构 或 远 程 办 公 人 员 站 点 的 低 速 连 接 ( 低 于 56kbps) 组 成 时 由 于 速 度 不 匹 配, 当 中 心 站 点 发 送 数 据 的 速 度 高 于 远 程 站 点 能 够 接 收 的 速 度 时, 分 支 机 构 或 远 程 办 公 人 员 站 点 的 流 量 通 常 存 在 瓶 颈 这 导 致 在 最 后 交 换 机 的 一 瓶 颈 在 远 程 点 路 由 器 前 如 果 您 是 提 供 子 速 率 服 务 的 服 务 提 供 商, 此 功 能 将 使 您 能 够 使 用 路 由 器, 将 您 的 T1 或 T3 链 路 分 为 更 小 的 信 道 您 可 以 为 每 个 子 接 口 配 置 令 牌 过 滤 器 桶, 使 之 与 用 户 定 购 的 服 务 匹 配 在 帧 中 继 连 接 上, 您 可 能 希 望 路 由 器 抑 制 数 据 流, 而 不 是 将 数 据 流 发 送 到 网 络 中 限 制 流 量 将 限 制 在 服 务 提 供 商 的 网 云 的 包 丢 失 基 于 BECN 的 控 制 功 能, 使 您 能 够 根 据 从 网 络 中 收 到 的 BECN 标 记 数 据 包, 让 路 由 器 动 态 控 制 数 据 流 这 种 控 制 将 信 息 包 保 留 在 路 由 器 的 缓 冲 区, 以 便 减 少 从 路 由 器 到 帧 中 继 网 络 的 数 据 流 路 由 器 控 制 子 接 口 上 的 数 据 流, 当 少 量 的 BECN 标 记 的 信 息 包 收 到 时, 速 率 也 会 增 加 通 用 流 量 整 形 的 命 令 要 定 义 速 率 控 制, 请 使 用 此 命 令 : traffic-shape rate 位 元 速 率 [burst-size [excess-burst-size]] [group access-list] 要 节 流 在 帧 中 继 接 口 的 BECN 使 用 此 命 令 : traffic-shape.adaptive [bit-rate] 如 果 要 配 置 帧 中 继 子 接 口 来 评 估 接 收 BECN 的 可 用 带 宽, 请 使 用 traffic-shape adaptive 命 令 注 意 : 在 您 能 够 使 用 traffic-shape adaptive 命 令 之 前, 您 必 须 在 带 有 traffic-shape rate 命 令 的 接 口 上 启 用 流 量 整 形 为 traffic-shape rate 命 令 指 定 的 比 特 率 是 上 限, 为 traffic-shape adaptive 命 令 指 定 的 比 特 率 是 下 限 ( 通 常 为 CIR 值 ), 当 接 口 接 收 BECN 时, 数 据 流 整 形 的 比 特 率 在 此 范 围 之 内 实 际 上 使 用 的 速 率 通 常 在 这 两 速 率 之 间 您 应 该 在 链 路 两 端 配 置 traffic-shape adaptive 命 令, 因 为 该 命 令 也 会 配 置 流 末 端 的 设 备, 将 转 发 显 式 拥 塞 通 知 (FECN) 信 号 作 为 反 映 为 BECN 既 使 数 据 流 主 要 在 一 个 方 向, 这 也 能 使 高 速 端 的 路 由 器 发 现 和 适 应 拥 塞 示 例 以 下 示 例 配 置 了 接 口 0.1 上 的 流 量 整 形, 上 限 为 ( 通 常 为 Bc + Be)128 kbps, 下 限 为 64 kbps 这 允 许 链 路 运 行 速 率 从 64kbps 到 128kbps, 具 体 取 决 于 拥 塞 程 度 如 果 中 心 侧 有 一 个 256 kbps 的 上 限, 您 应 该 使 用 最 低 的 上 限 值 这 是 什 么 我 们 在 这 些 路 由 器 配 置 : Central# interface serial 0 encapsulation-frame-relay interface serial 0.1 traffic-shape rate traffic-shape adaptive Client# interface serial 0 encapsulation-frame-relay interface serial 0.1 traffic-shape rate traffic-shape adaptive 帧 中 继 流 量 整 形 在 通 用 流 量 整 形 中, 您 只 能 为 每 个 物 理 接 口 的 指 定 一 个 峰 值 速 率 ( 上 限 ), 为 每 个 子 接 口 指 定 一 个 CIR ( 下 限 ) 使 用 帧 中 继 流 量 整 形, 您 启 动 一 个 令 牌 桶 过 滤 器 每 条 虚 拟 电 路 在 帧 中 继 功 能 的 流 量 整 形 提 供 以 下 功 能 : 在 逐 个 VC 的 速 率 强 制 : 您 可 以 配 置 峰 值 速 率, 把 出 局 流 量 限 制 为 CIR 或 某 些 其 他 定 义 值, 例 如 突 发 信 息 速 率 (EIR) 在 逐 个 VC 的 概 括 的 BECN 支 持 : 路 由 器 能 监 控 BECN, 并 从 帧 中 继 网 络 限 制 根 据 BECN 标 记 的 信 息 包 反 馈 的 流 量

mppp-ddr.pdf

mppp-ddr.pdf DDR 多 链 路 PPP - 基 本 配 置 和 验 证 目 录 简 介 开 始 使 用 前 规 则 先 决 条 件 使 用 的 组 件 多 链 路 PPP 干 什 么 配 置 多 链 路 PPP 命 令 传 统 DDR 拨 号 原 型 (Dialer Profile) 验 证 MPPP 操 作 相 关 信 息 简 介 多 链 路 PPP ( 也 指 MP MPPP MLP 或 多 链 路 ) 提

More information

Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco

Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco Ch2 Cisco IOS Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco Cisco ROM ROM Cisco ROM(BIOS) ROM 1. POST Cisco 2. BootStrap Cisco IOS 3. IOS IOS IOS Cisco ROM ROM Cisco Flash Flash Flash IOS Cisco

More information

D. 192.168.5.32 E. 192.168.5.14 答 案 :C 3. 工 作 站 A 配 置 的 IP 地 址 为 192.0.2.24/28. 工 作 站 B 配 置 的 IP 地 址 为 192.0.2.100/28. 两 个 工 作 站 之 间 有 直 通 线 连 接, 两 台

D. 192.168.5.32 E. 192.168.5.14 答 案 :C 3. 工 作 站 A 配 置 的 IP 地 址 为 192.0.2.24/28. 工 作 站 B 配 置 的 IP 地 址 为 192.0.2.100/28. 两 个 工 作 站 之 间 有 直 通 线 连 接, 两 台 CCNP 学 前 测 试 题 都 选 自 官 方 的 全 真 考 试 题, 共 100 道 题 实 际 测 试 选 60 道 题, 同 官 方 正 式 考 题 数 目 基 本 一 致, 因 此 等 于 是 模 拟 考 试, 采 用 网 上 形 式 进 行 测 评 学 前 测 评 目 的 是 为 了 检 验 大 家 对 CCNA 阶 段 知 识 掌 握 的 程 度, 同 时 对 CCNA 最 核 心

More information

IP-Routing-05.pdf

IP-Routing-05.pdf RI P R I P - 2 RIP -1 R I P - 2 DV RIP -1 RIP-2 16... RIP-2 RIP-2 RIP -1 R I P - 2 RIP-2 RIP-2 RIP-2 V L S M disc ontiguous addr ess sp ace C I D R Cla ssless In ter -Dom ain Routing 121 1 2 2 IP RIP-2

More information

两个串行接口上通过虚拟模板的多链路

两个串行接口上通过虚拟模板的多链路 两个串行接口上通过虚拟模板的多链路 目录 简介先决条件要求使用的组件相关产品规则配置网络图配置验证 show 输出示例故障排除故障排除资源故障排除命令调试输出示例相关信息 简介 多链路 PPP (MLP) 对拨号程序接口 ( 如 ISDN 同步和异步接口 ) 上的负载进行均衡 MLP 对数据包进行分割, 并通过并行电路发送各个片段 这样,MLP 可以提高吞吐量, 并减小系统间的延迟 MLP 提供了一种跨多个逻辑数据链路对数据报进行分割

More information

ch08.PDF

ch08.PDF 8-1 CCNA 8.1 CLI 8.1.1 8-2 8-3 8.1.21600 2500 1600 2500 / IOS 8-4 8.2 8.2.1 A 5 IP CLI 1600 2500 8-5 8.1.2-15 Windows 9598NT 2000 HyperTerminal Hilgraeve Microsoft Cisco HyperTerminal Private Edition (PE)

More information

通过动态路由协议实现链路备份

通过动态路由协议实现链路备份 通过动态路由协议实现链路备份 实验名称 通过动态路由协议实现链路备份 实验目的 掌握通过在不同链路上配置不同的路由协议实现链路备份 背景描述 你是公司高级网络管理员, 公司内部有一个很重要的服务器所在网段为 192.168.12.0/24, 平常访问通过 R1,R3 的 OSPF 路由协议, 为了保证该网段随时能够访问, 不能因为链路故障出问题, 要求你实现一个备份冗余的功能, 请给予支持 实现功能

More information

¶C¶L§§¬_™¨ A.PDF

¶C¶L§§¬_™¨ A.PDF 1 9 3 1 9 4 / 7.1 / 1 9 5 7.2 % netstat -rn Routing tables Destination Gateway Flags Refcnt Use Interface 127.0.0.1 127.0.0.1 UH 1 132 lo0 172.16.12.0 172.16.12.2 U 26 49041 le0 1 9 6 / % ping -s almond

More information

IS-IS路由协议中文教程v1

IS-IS路由协议中文教程v1 IS-IS v1.0 Chapter 0 Preface Statement BSCI Building Scalable Cisco Internetworks Configuring IS-IS Protocol IS-IS IS-IS OSI TCP/IP IS-IS OSPF Cisco System BSCI Student Guide Outline 1 OSI IS-IS 2 IS-IS

More information

untitled

untitled 7.1 7.1.1 IP R1 N N,R1,M IP 1 7.1.2 [Quidway]display ip routing Routing Tables: Destination/Mask proto pref Metric Nexthop Interface 0.0.0.0/0 Static 60 0 120.0.0.2 Serial0 8.0.0.0/8 RIP 100 3 120.0.0.2

More information

untitled

untitled 6.1 HDLC 6.1.1 HDLC HDLC HDLC F F 1 HDLC DDN HDLC 8 8 HDLC HDLC HDLC 1 6.2 PPP MP 6.2.1 PPP PPP PSTN/ ISDN PPP PPP SLIP PPP PPP Point-to-Point Protocol SLIP SLIP PPP PPP OSI PPP PPP PPP X.25, Frame Relay

More information

Simulator By SunLingxi 2003

Simulator By SunLingxi 2003 Simulator By SunLingxi sunlingxi@sina.com 2003 windows 2000 Tornado ping ping 1. Tornado Full Simulator...3 2....3 3. ping...6 4. Tornado Simulator BSP...6 5. VxWorks simpc...7 6. simulator...7 7. simulator

More information

工程师培训

工程师培训 .1 TCP/IP TCP/IP 1 .2.2.1 Host 1960 S 1970 S Host Low Speed Lines 1970 S 1980 S pc Server Local Interneting 1980 S 1990 S Branch. pc Branch. WAN Branch. pc pc IBM SNA IBM X.25 2 .2.2 OSI OSI Application

More information

IP505SM_manual_cn.doc

IP505SM_manual_cn.doc IP505SM 1 Introduction 1...4...4...4...5 LAN...5...5...6...6...7 LED...7...7 2...9...9...9 3...11...11...12...12...12...14...18 LAN...19 DHCP...20...21 4 PC...22...22 Windows...22 TCP/IP -...22 TCP/IP

More information

(CISCO????????)

(CISCO????????) CISCO 路 由 器 产 品 配 置 手 册 第 一 章 路 由 器 配 置 基 础... 2 一 基 本 设 置 方 式... 2 二 命 令 状 态... 2 三 设 置 对 话 过 程... 3 四 常 用 命 令... 5 五 配 置 IP 寻 址... 6 六 配 置 静 态 路 由... 9 第 二 章 广 域 网 协 议 设 置... 11 一 HDLC... 11 二 PPP...

More information

ARP ICMP

ARP ICMP ARP ICMP 2 9-1 ARP 9-2 ARP 9-3 ARP 9-4 ICMP 9-5 ICMP 9-6 ICMP 9-7 ICMP 3 ARP ICMP TCP / IP, IP ARP ICMP 3 IP, ARP ICMP IP ARP ICMP 2, 4 9-1 ARP, MAC, IP IP, MAC ARP Address Resolution Protocol, OSI ARP,,

More information

epub

epub 3 Cisco 3.1 S e t u p C i s c o C i s c o Cisco IOS C i s c o 3.2 Te l n e t T F T P 3-1 3-1 configure terminal configure memory Configure network t e l n e t < C t r l - Z > conf t N V R A M T F T P I

More information

第3章

第3章 本 章 涵 盖 以 下 主 题 全 局 单 播 地 址 路 由 和 子 网 划 分 : 本 节 通 过 与 IPv4 相 比 较, 介 绍 了 IPv6 地 址 IPv4 路 由 的 概 念, 以 及 怎 样 进 行 IPv6 子 网 划 分 IPv6 全 局 单 播 地 址 的 分 配 : 本 节 探 讨 了 怎 样 将 全 局 单 播 地 址 分 配 到 主 机 或 其 他 设 备 上 IPv6

More information

CISCO技术大全

CISCO技术大全 CISCO 5 1. Console 2. AUX MODEM 3. Ethernet TFTP 4. Ethernet TELNET 5. Ethernet SNMP, : 9600 8 1 : 1. router> 2. router# router> enable, router# 3. router(config)# router# configure terminal, router(config)#

More information

工程师培训

工程师培训 .1 Quidway 1 .2.2.1 ATM 2 .2.2 ( LAN ) ( WAN ) ( CONSOLE ) 3 .3.3.1 LAN Ethernet Token Bus Token Ring...... Local Area Network LAN 1 2 3 LAN LAN IBM LAN 4 .3.2 10M 100M 1000M 10Mbps 100Mbps 1000Mbps IEEE

More information

Session Dan Gill 2 IP WAN WAN? Networker NSC-114 RST-271 NSC-211 : MTBF: MTTR: MTBF MTTR : MTBF? MTTR? MTTR MTTR MTTR MTBF MTTR Mom-and-apple-pie MTBF MTBF (UPS, ) Mom-and-apple-pie Increase MTBF MTBF?

More information

SL2511 SR Plus 操作手冊_單面.doc

SL2511 SR Plus 操作手冊_單面.doc IEEE 802.11b SL-2511 SR Plus SENAO INTERNATIONAL CO., LTD www.senao.com - 1 - - 2 - .5 1-1...5 1-2...6 1-3...6 1-4...7.9 2-1...9 2-2 IE...11 SL-2511 SR Plus....13 3-1...13 3-2...14 3-3...15 3-4...16-3

More information

Microsoft Word - CCNA2_Exploration_instructor_40_CoverSheet.DOC

Microsoft Word - CCNA2_Exploration_instructor_40_CoverSheet.DOC 本 文 档 是 Cisco Systems, Inc. 的 专 有 财 产, 为 Cisco Networking Academy 讲 授 CCNA Exploration 路 由 协 议 和 概 念 课 程 的 教 师 专 用, 允 许 打 印 或 复 制 作 非 商 业 用 途 实 验 1.5.1: 网 络 布 线 和 基 本 路 由 器 配 置 ( 教 师 版 ) 拓 扑 图 地 址 分 配

More information

active phisical rp address: backup phisical rp address: 截取部分 TOPO 图说明到 不通的问题 : internet internet tengige 0/0/0/0 tengige

active phisical rp address: backup phisical rp address: 截取部分 TOPO 图说明到 不通的问题 : internet internet tengige 0/0/0/0 tengige ASR9000 ping 丢包 troubleshooting 目录 硬件平台软件版本案例介绍问题分析思路问题总结经验总结相关命令 硬件平台 ASR9000 软件版本 4.2.0 案例介绍 拓扑示例 : 问题, 客户从外网 internet ping 3 个 vrrp subnet 的地址时候始终只能通一个 IP 地址 : vrrp virtual IP :2.2.2.129 其他不能 ping 通的

More information

ebook71-13

ebook71-13 13 I S P Internet 13. 2. 1 k p p p P P P 13. 2. 2 1 3. 2. 3 k p p p 1 3. 2. 4 l i n u x c o n f P P P 13. 2. 5 p p p s e t u p 13. 2. 6 p p p s e t u p P P P 13. 2. 7 1 3. 2. 8 C a l d e r a G U I 13.

More information

路 由 器 处 于 用 户 命 令 状 态, 这 时 用 户 可 以 看 路 由 器 的 连 接 状 态, 访 问 其 它 网 络 和 主 机, 但 不 能 看 到 和 更 改 路 由 器 的 设 置 内 容 2. router# 在 router> 提 示 符 下 键 入 enable, 路 由

路 由 器 处 于 用 户 命 令 状 态, 这 时 用 户 可 以 看 路 由 器 的 连 接 状 态, 访 问 其 它 网 络 和 主 机, 但 不 能 看 到 和 更 改 路 由 器 的 设 置 内 容 2. router# 在 router> 提 示 符 下 键 入 enable, 路 由 CISCO 路 由 器 配 置 手 册 一 基 本 设 置 方 式 一 般 来 说, 可 以 用 5 种 方 式 来 设 置 路 由 器 : 1.Console 口 接 终 端 或 运 行 终 端 仿 真 软 件 的 微 机 ; 2.AUX 口 接 MODEM, 通 过 电 话 线 与 远 方 的 终 端 或 运 行 终 端 仿 真 软 件 的 微 机 相 连 ; 3. 通 过 Ethernet 上

More information

第 1 部 分 : 检 查 网 络 要 求 在 第 1 部 分 中, 您 将 研 究 使 用 172.16.128.0/17 网 络 地 址 为 拓 扑 图 中 显 示 的 网 络 开 发 VLSM 地 址 方 案 的 网 络 要 求 注 意 : 您 可 以 使 用 Windows 计 算 器 应

第 1 部 分 : 检 查 网 络 要 求 在 第 1 部 分 中, 您 将 研 究 使 用 172.16.128.0/17 网 络 地 址 为 拓 扑 图 中 显 示 的 网 络 开 发 VLSM 地 址 方 案 的 网 络 要 求 注 意 : 您 可 以 使 用 Windows 计 算 器 应 拓 扑 目 标 第 1 部 分 : 检 查 网 络 要 求 第 2 部 分 : 设 计 VLSM 地 址 方 案 第 3 部 分 : 布 线 和 配 置 IPv4 网 络 背 景 / 场 景 可 变 长 度 子 网 掩 码 (VLSM) 旨 在 避 免 浪 费 IP 地 址 使 用 VLSM, 会 对 网 络 多 次 进 行 子 网 划 分 此 过 程 可 重 复 多 次, 从 而 根 据 每 个

More information

02.实验二:虚拟局域网与VLAN间通信

02.实验二:虚拟局域网与VLAN间通信 计算机网络 实验指导 实验二 : 虚拟局域网与 VLAN 间通信 一 实验目的 1 理解交换机的工作原理; 2 掌握交换机的带外管理和带内管理的基本方法; 3 理解虚拟局域网(VLAN) 的基本概念和原理 ; 4 掌握在多台二层交换机间划分虚拟局域网的详细内容和操作命令; 5 掌握 VLAN 间通信的基本原理与配置方法 二 实验学时 2 学时 三 实验类型 综合性 四 实验需求 1 硬件每人配备计算机

More information

配置 ATM 与 PPP 的互通

配置 ATM 与 PPP 的互通 配置 ATM 与 PPP 的互通 目录 简介先决条件要求使用的组件规则配置 MGX 8220 架子配置 BPX 配置与 ATM 连接的路由器配置串口连接的路由器验证连通性 MGX 8220 机架 BPX 路由器相关信息 简介 本文包含 ATM 到点到点协议 (PPP) 的简单配置 此配置旨在用作如何在 Cisco 路由器和 Cisco/StrataCom WAN 交换机之间建立 ATM-PPP 网际互联的示例

More information

CCNA 講義

CCNA 講義 CCNA 筆 記 王 振 民 目 錄 第 1 章 Packet Tracer 的 使 用... 2 第 1 節 安 裝... 2 第 2 節 建 置 網 路 環 境 _01( 二 台 PC+ 一 台 HUB)... 8 第 3 節 Pc 的 設 定 :IP, cmd...... 10 第 4 節 傳 送 封 包 (ICMP 封 包 檢 視...)... 13 第 2 章 基 礎 知 識... 14

More information

一.NETGEAR VPN防火墙产品介绍

一.NETGEAR VPN防火墙产品介绍 NETGEAR VPN NETGEAR 6 http://www.netgear.com.cn - 1 - NETGEAR VPN... 4 1.1 VPN...4 1.2 Dynamic Domain Name Service...4 1.3 Netgear VPN...4 Netgear VPN... 6 2.1 FVS318 to FVS318 IKE Main...7 2.1.1 A VPN

More information

TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP

TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP TCP/IP : TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP 1. ASCII EBCDIC Extended Binary-Coded Decimal Interchange Code 2. / (1) (2) Single System Image SSI) (3) I/O (4) 3.OSI OSI Open System Interconnection

More information

计算机网络概论

计算机网络概论 1 repeater bridge router gateway V.S OSI Repeater(Hub) 1 Repeater 2 3 ( Hub 4 Bridge 1 Bridge 2 N N DL1 DL1 DL2 DL2 Ph1 Ph1 Ph2 Ph2 1 2 Bridge 3 MAC Ethernet FDDI MAC MAC Bridge 4 5 6 7 50873EA6, 00123456

More information

FortiGate-v5.2-PPPOE 拨号协商时的 AC-name 和 Service-name 版本 1.0 时间 2015 年 3 月 支持的版本 FortiOS v5.2.x 作者 黄豪赫 状态 已审核 反馈

FortiGate-v5.2-PPPOE 拨号协商时的 AC-name 和 Service-name 版本 1.0 时间 2015 年 3 月 支持的版本 FortiOS v5.2.x 作者 黄豪赫 状态 已审核 反馈 FortiGate-v5.2-PPPOE 拨号协商时的 AC-name 和 Service-name 版本 1.0 时间 2015 年 3 月 支持的版本 FortiOS v5.2.x 作者 黄豪赫 状态 已审核 反馈 support_cn@fortinet.com 1 目 录 简介...3 PPPoE 发现阶段简介...3 相关组件...4 参考文档...4 FortiGate 相关命令介绍...

More information

通过 G.SHDSL 端口进行 CPE 背对背连接的配置

通过 G.SHDSL 端口进行 CPE 背对背连接的配置 通过 G.SHDSL 端口进行 CPE 背对背连接的配置 目录 简介先决条件要求使用的组件规则配置网络图配置命令参考 dsl equipment-type dsl linerate dsl operating-mode (g.shdsl) 验证排除故障故障排除命令相关信息 简介 本文为两路由器的配置提供一配置示例背对背通过多速率对称高速的数字用户线 (G.SHDSL) 端口 它描述终止从另一个远程

More information

配置 Cisco 827 上带VPN IPSec NAT 超载的PPPoE

配置 Cisco 827 上带VPN IPSec NAT 超载的PPPoE 配置 Cisco 827 上带 VPN IPSec NAT 超载的 PPPoE 目录 简介开始使用前规则先决条件使用的组件配置网络图配置验证故障排除故障排除命令相关信息 简介 Cisco 827 路由器通常是 DSL 客户端前置设备 (CPE) 在此示例配置中, 思科 827 配置用于以太网点对点协议 (PPPoE 的 ), 用作使用思科 3600 路由器的 LAN-to-LAN IPSec 隧道中的对端

More information

DCR 1700系列路由器配置手册

DCR 1700系列路由器配置手册 ....2...3...5...7...8 HDLC...8 SLIP...9 PPP...11 X.25...13 Frame Relay...16 ISDN...19 PSTN...21...23...23 RIP...24 OSPF...25 DEIGRP CISCO EIGRP...26 BGP...28...30...33...33 NAT...34 VPN(IPSec)...35 VPN(GRE)...38

More information

epub 30-12

epub 30-12 12 IP I P I P E s t a b l i s h e d I P I P l o c k - a n d - k e y V T Y 12.1 1) 2) D D R 3) 4) 5) 12.2 IP C i s c o 1) I P I P I P 402 CCIE 1 I P 0 0.0.0.0 1 3 150. 1. 1 1 ~ 255 150. 1. 1. 0 2) Inbound

More information

epub 30-5

epub 30-5 5 AT M Cisco 4500 AT M Cisco AT M AT M 5.1 AT M WA N C i s c o AT M AT Cisco IOS AT M 5.1.1 ATM AT M 53 5-1 5-2 AT M AT M AT M AT AT M 5-1 L A N / WA N H D L C 802. 3 5-1 LAN / WAN 5 185 ATM NIC ATM NIC

More information

1 1 2 OSPF RIP 2

1 1 2 OSPF RIP 2 MPLS VPN 1. TCP/IP IP IP IP IP 1 1 2 OSPF RIP 2 2 RIP OSPF BGP DVMRP IS- IS IP 1. Unicast Routing Protocol Multicast Routing Protocol RIP OSPF BGP IS-IS DVMRP PIM-SM PIM-DM 2. IGP EGP IGPRIP OSPF IS-ISEGP

More information

QL1880new2.PDF

QL1880new2.PDF ADSL Modem 1 MODEM 56K MODEM 128K ISDN INTERNET ADSL Modem VOD ADSL ADSL 2 1.1 ADSL 1.2 1.3 KM300A 2.1 2.2 2.3 2.4 2.5 KM300A 2.6 web 2.7 1.1ADSL 1.2 1.3 2.1 ADSL 2.2 ADSL 3 ADSL KM300A ADSL KM300A DIY

More information

计算机网络

计算机网络 (delay latency) = + + LEC. A B A 0 0 0 B .6. = 0ms, 0Mb/s, 0x0 - x0x0 =x0 bit RTT RTT (Round-Trip Time) .7 OSI/RM OSI/RM OSI/RM TCP/IP (application layer) (transport layer) (network layer)

More information

ebook20-8

ebook20-8 8 Catalyst 5000 7 V L A N C a t a l y s t V L A N V L A N 8.1 VLAN VTP V L A N A VLAN VLAN 10 VLAN 20 VLAN 10 VLAN 20 B VLAN VLAN 10 VLAN 20 VLAN 10 C VLAN VLAN 10 VLAN 20 VLAN 10 VLAN 20 8-1 VLAN 8 Catalyst

More information

財金資訊-80期.indd

財金資訊-80期.indd IPv6 / LINE YouTube TCP/IP TCP (Transmission Control Protocol) IP (Internet Protocol) (node) (address) IPv4 168.95.1.1 IPv4 1981 RFC 791 --IP IPv4 32 2 32 42 IP (Internet Service Provider ISP) IP IP IPv4

More information

目录 简介... 3 BGP 重发布进 OSPF 环境拓扑图... 3 BGP 重发布进 OSPF 路由过滤... 4 FGT200B 关键配置... 4 接口 IP 配置... 4 Route-Map... 4 BGP 的配置... 5 FGT100E 关键配置... 5 接口 IP 及 BGP

目录 简介... 3 BGP 重发布进 OSPF 环境拓扑图... 3 BGP 重发布进 OSPF 路由过滤... 4 FGT200B 关键配置... 4 接口 IP 配置... 4 Route-Map... 4 BGP 的配置... 5 FGT100E 关键配置... 5 接口 IP 及 BGP BGP 与 OSPF 之间重发布时使用 Route-Map 进行路由过滤 版本 1.0 时间 2017 年 9 月 5 日星期二 支持的版本 FortiGate v5.0 v5.2 v5.4 v5.6 作者 状态 反馈 刘康明 已审核 support_cn@fortinet.com 目录 简介... 3 BGP 重发布进 OSPF 环境拓扑图... 3 BGP 重发布进 OSPF 路由过滤... 4

More information

注意 :CCNA 动手实验所用的路由器是采用 Cisco IOS Release 15.2(4)M3(universalk9 映像 ) 的 Cisco 1941 集成多业务路由器 (ISR) 所用的交换机是采用 Cisco IOS Release 15.0(2)(lanbasek9 映像 ) 的 C

注意 :CCNA 动手实验所用的路由器是采用 Cisco IOS Release 15.2(4)M3(universalk9 映像 ) 的 Cisco 1941 集成多业务路由器 (ISR) 所用的交换机是采用 Cisco IOS Release 15.0(2)(lanbasek9 映像 ) 的 C 拓扑 地址分配表 设备 接口 IP 地址 子网掩码 默认网关 R1 G0/1 192.168.1.1 255.255.255.0 未提供 S1 VLAN 1 未提供 未提供 未提供 PC-A 网卡 192.168.1.3 255.255.255.0 192.168.1.1 目标 第 1 部分 : 设置拓扑并初始化设备 设置设备以匹配网络拓扑 初始化并重新启动 ( 必要时 ) 路由器和交换机 第 2

More information

untitled

untitled (ZCNE) ZCNE 1... 1 1.1... 1 1.2... 2 1.3... 2 1.3.1... 2 1.3.2... 2 1.3.3... 2 1.4... 2 1.4.1... 2 1.4.2... 2 1.5... 2 1.5.1... 2 1.5.2... 2 1.5.3... 2 1.5.4... 2 1.5.5... 2 1.6... 2 1.7... 2 1.8... 2

More information

epub 61-2

epub 61-2 2 Web Dreamweaver UltraDev Dreamweaver 3 We b We b We Dreamweaver UltraDev We b Dreamweaver UltraDev We b We b 2.1 Web We b We b D r e a m w e a v e r J a v a S c r i p t We b We b 2.1.1 Web We b C C +

More information

Procedural Lab Template, Student Version, Required Components

Procedural Lab Template, Student Version, Required Components 拓 樸 圖 位 址 配 置 表 設 備 介 面 IP 位 址 子 網 路 遮 罩 預 設 閘 道 R1 Fa0/0 192.168.1.1 255.255.255.0 不 適 用 S0/0/0 192.168.2.1 255.255.255.0 不 適 用 R2 Fa0/0 192.168.3.1 255.255.255.0 不 適 用 S0/0/0 192.168.2.2 255.255.255.0

More information

GPRS IP MODEM快速安装说明

GPRS IP MODEM快速安装说明 GF-3026D CDMA 无 线 路 由 器 用 户 手 册 北 京 嘉 复 欣 科 技 有 限 公 司 地 址 : 北 京 市 海 淀 区 阜 成 路 115 号 北 京 印 象 2 号 楼 213 室 电 话 :86-10-88122130 88153193 88153197 传 真 :86-10-88122129 网 站 :http://www.garefowl.com/ 目 录 一 产 品

More information

网工新答案

网工新答案 2005 年 5 月 29 日 软 考 2005 年 上 半 年 网 络 工 程 师 上 午 试 题 ( 参 考 答 案 ) ( 特 别 声 明, 此 答 案 只 作 参 考 ) 本 文 是 经 过 三 审 后 的 CIU 网 工 上 午 参 考 答 案 ( 正 确 率 在 92%-95% 之 间, 因 为 种 种 原 因, 不 能 与 标 准 答 案 完 全 相 同, 请 大 家 理 解 ) 如

More information

实验二、路由器的基本配置

实验二、路由器的基本配置 实验十三 路由器广域网 PPP 封装 CHAP 验证配置 一 实验目的 1. 掌握 CHAP 验证配置 2. 理解验证过程 二 应用环境 基于安全的考虑, 需要路由器双方经过验证后才能建立连接 三 实验设备 1. DCR-1751 两台 2. CR-V35MT 一条 3. CR-V35FC 一条 四 实验拓扑 五 实验要求 Router-A Router-B 接口 IP 地址 接口 IP 地址 S1/1

More information

ebook140-11

ebook140-11 11 VPN Windows NT4 B o r d e r M a n a g e r VPN VPN V P N V P N V P V P N V P N TCP/IP 11.1 V P N V P N / ( ) 11.1.1 11 V P N 285 2 3 1. L A N LAN V P N 10MB 100MB L A N VPN V P N V P N Microsoft PPTP

More information

KillTest 质量更高 服务更好 学习资料 半年免费更新服务

KillTest 质量更高 服务更好 学习资料   半年免费更新服务 KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务 Exam : 350-001-LAB : Title CCIE-ROUTING AND SWITCHING QUALIFICATION (Lab exam) Version : Demo 1 / 28 N1. 2 / 28 Part-1 Bridge and Switching 1.1 vtp

More information

指定静态路由的下一跳IP地址

指定静态路由的下一跳IP地址 指定静态路由的下一跳 IP 地址 目录 简介背景信息对广播接口的静态路由浮动静态路由示例问题解决方案结论 简介 本文描述静态路由基本概念 问题场景用于为了展示指定接口下一跳 IP 地址可以被到达的情况变得理想, 当您配置静态路由时 失败可能导致不需要的行为和一个残破的网络状况 背景信息 由于各种各样的原因使用静态路由并且是常用的, 当没有动态路由对目的 IP 地址时, 或者, 当您要动态地改写获取的路由时

More information

ebook140-8

ebook140-8 8 Microsoft VPN Windows NT 4 V P N Windows 98 Client 7 Vintage Air V P N 7 Wi n d o w s NT V P N 7 VPN ( ) 7 Novell NetWare VPN 8.1 PPTP NT4 VPN Q 154091 M i c r o s o f t Windows NT RAS [ ] Windows NT4

More information

ebook106-17

ebook106-17 17 Mark Kadrich ( R A D I U S ) S L I P C S L I P P P P I P I n t e r n e t I n t e r n e t 110 ( / ) 24 7 70 80 56 K ( P S T N ) 17.1 / ( m o - d e m ) P S T N ( 17-1 ) P S T N 17-1 PSTN 176 17.1.1 ISDN

More information

一、选择题

一、选择题 计 算 机 网 络 基 础 第 7 章 练 习 思 考 与 认 识 活 动 一 选 择 题 1. 下 面 命 令 中, 用 于 检 查 WINDOWS2000 下 TCP/IP 配 置 信 息 的 是 ( ) A. cmd B. nslookup C. ipconfig D. ping 2. 内 部 网 关 协 议 RIP 是 一 种 广 泛 使 用 的 基 于 距 离 矢 量 算 法 的 协 议

More information

Exam1

Exam1 学网络技术去鸿鹄论坛命运的改变从技术开始 鸿鹄团队致力于为每一位网络技术爱好者提供帮助 有事您发帖, 斑竹为您跑腿, 给您答疑 CCNA 题库战报交流群 :82327397 欢迎备考 CCNA 的朋友加入, 一起讨论交流, 通过 CCNA 考试! CCNA 最新题库 / 最新战报发布区 : http://om/forum-261-1.html CCNA 考试代号 : 640-802 考试时间 : 中文

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

Microsoft Word - chp8帧中继.doc

Microsoft Word - chp8帧中继.doc 第 8 章帧中继 帧中继线路是中小企业常用的广域网线路, 其通信费用较低 由于帧中继技术的一些特殊性使得帧中继的配置较为复杂, 特别是在帧中继上运行路由协议时更是如此 作为入门, 对帧中继的理解应着重放在 DLCI PVC 帧中继映射和子接口等概念上 本章通过几个实验详细介绍了帧中继的关键概念 8.1.1 什么是帧中继 8.1 帧中继简介 帧中继 (Frame Relay, FR) 是面向连接的第二层传输协议,

More information

Microsoft Word - chp3静态路由.doc

Microsoft Word - chp3静态路由.doc 第 3 章静态路由 转发数据包是路由器的最主要功能 路由器转发数据包时需要查找路由表, 管理员可以通过手工的方法在路由器中直接配置路由表, 这就是静态路由 虽然静态路由不适合于在大的网络中使用, 但是由于静态路由简单 路由器负载小 可控性强等原因, 在许多场合中还经常被使用 本章将介绍静态路由的配置, 同时为以后配置动态路由奠定基础 3.1.1 静态路由介绍 3.1 静态路由与默认路由 路由器在转发数据时,

More information

Bus Hound 5

Bus Hound 5 Bus Hound 5.0 ( 1.0) 21IC 2007 7 BusHound perisoft PC hound Bus Hound 6.0 5.0 5.0 Bus Hound, IDE SCSI USB 1394 DVD Windows9X,WindowsMe,NT4.0,2000,2003,XP XP IRP Html ZIP SCSI sense USB Bus Hound 1 Bus

More information

IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG

IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG --------------------------------------------TABLE OF CONTENTS------------------------------------------

More information

bbs.vlan5.com

bbs.vlan5.com Catalyst 3750 交换机上的跨堆叠 EtherChannel 配置示例 内容 前言前提条件需求使用的组件惯例背景理论链路聚合控制协议 (LACP) 和端口聚合协议 (PAgP) EtherChannel 和交换机堆叠配置指南配置网络图配置验证故障排除相关信息 前言 本文档提供在运行 Cisco IOS 系统软件的 Cisco Catalyst 3750 交换机上配置跨堆叠 EtherChannel

More information

(UTM???U_935_938_955_958_959 V2.1.9.1)

(UTM???U_935_938_955_958_959 V2.1.9.1) 192.16 www.sharetech.com.tw UTM 多 功 能 防 火 牆 管 理 者 手 冊 V 2.1.9.1 目 錄 第 一 章 安 裝 與 訊 息... 7 1-1 建 議 的 安 裝 設 定 圖... 8 1-2 軟 體 安 裝 設 定... 9 1-3 首 頁 訊 息... 14 1-4 型 號 與 功 能 對 照 表... 17 第 二 章 系 統 設 定... 19 2-1

More information

《计算机网络》实验指导书

《计算机网络》实验指导书 1 实 验 一 网 络 组 建 与 管 理 一. 实 验 目 的 1. 掌 握 平 行 双 绞 线 和 交 叉 双 绞 线 的 制 作 方 法 ( 初 级 ) 2. 掌 握 对 等 网 和 代 理 服 务 器 网 络 的 组 建 ( 初 级 ) 3. 会 用 ipconfig 和 ping 命 令 ( 初 级 ) 4. 掌 握 网 络 中 文 件 夹 共 享 和 打 印 机 共 享 ( 初 级 )

More information

Microsoft Word - Che2_Lab_ _Config-Basic-Router-CLI-Students.doc

Microsoft Word - Che2_Lab_ _Config-Basic-Router-CLI-Students.doc 實驗 5.3.5 使用 IOS CLI 設定路由器基本設定 路由器編號 路由器名稱 Fast Ethernet 0 位址 Serial 0 位址 介面類型 兩個介面的子網路遮罩 路由器 1 R1 172.16.0.1 172.17.0.1 DCE 255.255.0.0 路由器 2 R2 172.18.0.1 172.17.0.2 DTE 255.255.0.0 目標 為路由器設定裝置主機名稱 設定控制台密碼

More information

Symantec™ Sygate Enterprise Protection 防护代理安装使用指南

Symantec™ Sygate Enterprise Protection 防护代理安装使用指南 Symantec Sygate Enterprise Protection 防 护 代 理 安 装 使 用 指 南 5.1 版 版 权 信 息 Copyright 2005 Symantec Corporation. 2005 年 Symantec Corporation 版 权 所 有 All rights reserved. 保 留 所 有 权 利 Symantec Symantec 徽 标 Sygate

More information

Microsoft Word - 目錄.doc

Microsoft Word - 目錄.doc xxvii 簡 介 本 書 涵 蓋 相 當 廣 泛 的 網 路 主 題, 示 範 Cisco 路 由 器 的 設 定 方 式, 並 解 說 如 何 判 斷 設 定 的 功 能 是 否 生 效 因 此 本 書 很 適 合 作 為 IP 路 由 與 IP 路 由 協 定 的 參 考 用 書 不 過, 因 本 書 屬 於 Cisco Press 專 業 認 證 手 冊 系 列 叢 書 之 一, 故 協 助

More information

WAN广域网技术

WAN广域网技术 学习沉淀成长分享 WAN 红茶三杯 ( 朱 SIR) 微博 :http://t.sina.com/vinsoney Latest update: 2012-06-01 课程目标 广域网基础 PPP FrameRelay 广域网基础 什么是广域网 广域网链路类型 常见的广域网封装 WAN 简介 为什么需要 WAN? 分区或分支机构的员工需要与总部通信并共享数据 组织经常需要与其它组织远距离共享信息 经常出差的员工需要访问公司网络信息

More information

ebook48-8

ebook48-8 C i s c o 8SRB/RSRB S R B S R S R B S R B S R BR S R BS R B I B M S R B C i s c o S R BR S R B D L S wd L S w 9 D L S w + 8.1 SRB C i s c os R B C i s c o WA N IBM SNAN e t B I O S S R B / R S R B C i

More information

计算机网络

计算机网络 gongwhboy@tom.com Internet 3 James F.Kurose Keith W.Ross 4 Andrew S.Tanenbaum 3 Larry L.Peterson, Bruce S.Davie 3 1. ISO OSI/RM( ) TCP/IP ( TELNET, FTP, SMTP ) (TCP UDP) IP 2. Internet : Internet 5 (1)

More information

1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005

1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005 1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005 1 1...3 2...20 3...28 4...41 5 Windows SQL Server...47 Microsoft SQL Server 2005 DBSRV1 Microsoft SQL Server

More information

F5270

F5270 Cisco 路 由 器 設 定 主 講 : 陳 建 民 本 章 提 要 4-1 Cisco 路 由 器 使 用 者 界 面 4-2 命 令 列 界 面 4-3 路 由 器 與 交 換 器 的 管 理 功 能 4-4 路 由 器 界 面 4-5 檢 視 儲 存 與 清 除 組 態 設 定 2 Cisco 路 由 器 3 4 5 6 Router physical characteristics 7 4-1

More information

第4章网络层_2_.doc

第4章网络层_2_.doc ( 章 节 专 题 首 页 ) 课 程 名 称 计 算 机 网 络 章 节 专 题 第 4 章 网 络 层 ( 二 ) 1.IP 数 据 报 的 格 式 ; 教 学 目 标 及 基 本 要 求 2. 理 解 子 网 划 分 的 意 义, 掌 握 如 何 划 分 子 网 ; 3. 理 解 超 网 构 造 原 理, 掌 握 构 造 超 网 ; 4. 知 道 网 际 控 制 报 文 协 议 ICMP 及

More information

Microsoft Word - frame-relay.doc

Microsoft Word - frame-relay.doc 实验目的 1. 掌握全网格型帧中继的配置 ; 2. 掌握帧中继子端口的配置 ; 3. 掌握帧中继的流量整形 Frame-relay 实验 实验原理 一 帧中继技术概述 1. 帧中继网简述 帧中继封装方式 :cisco 和 ietf 注意 : 帧中继只工作在 OSI 的物理层和数据链路层 2. DLCI LMI 的意义和类型 DLCI 用来标识 VC( 通常是 PVC) 的数字, 在 0~1023 之间

More information

IP Access Lists IP Access Lists IP Access Lists

IP Access Lists IP Access Lists IP Access Lists Chapter 10 Access Lists IP Access Lists IP Access Lists IP Access Lists Security) IP Access Lists Access Lists (Network router For example, RouterA can use an access list to deny access from Network 4

More information

9 Internet 10 Internet

9 Internet 10 Internet 1 2 3 4 5 6 Internet 7 8 9 Internet 10 Internet 11 12 1 1.1 1.2 1.3 1.4 1.5 1.6 1.1 1.1.1 20 50 20 60 ARPANET ARPANET Internet 20 70 ISO International Organization for Standardization TCP/IP 20 90 Internet

More information

Microsoft Word - lab2_4.doc

Microsoft Word - lab2_4.doc 网 络 工 程 实 验 4: 路 由 器 基 本 配 置 第 一 部 分 路 由 器 端 口 配 置 实 验 目 的 1. 熟 悉 路 由 设 备 以 及 了 解 路 由 器 的 常 见 端 口 种 类 ; 2. 掌 握 路 由 器 端 口 的 配 置 方 法 ; 3. 掌 握 观 察 和 调 试 路 由 器 的 基 本 方 法 背 景 知 识 路 由 器 端 口 即 指 路 由 器 与 网 络 中

More information

第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特 网 的 标 准 化 工 作 1.2.4 计 算 机 网 络 在

第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特 网 的 标 准 化 工 作 1.2.4 计 算 机 网 络 在 计 算 机 网 络 ( 第 4 版 ) 课 件 第 1 章 计 算 机 网 络 概 述 郭 庆 北 Ise_guoqb@ujn.edu.cn 2009-02-25 第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特

More information

ext-web-auth-wlc.pdf

ext-web-auth-wlc.pdf 使 用 无 线 局 域 网 控 制 器 的 外 部 Web 身 份 验 证 配 置 示 例 目 录 简 介 先 决 条 件 要 求 使 用 的 组 件 规 则 背 景 信 息 外 部 Web 身 份 验 证 过 程 网 络 设 置 配 置 为 来 宾 用 户 创 建 动 态 接 口 创 建 预 先 身 份 验 证 ACL 在 WLC 上 为 来 宾 用 户 创 建 本 地 数 据 库 配 置 外 部

More information

第3章 计算机网络体系结构

第3章  计算机网络体系结构 第 3 章 计 算 机 网 络 体 系 结 构 本 章 内 容 计 算 机 的 网 络 体 系 结 构 网 络 参 考 模 型 五 层 网 络 参 考 模 型 1 3.1 计 算 机 网 络 体 系 结 构 发 展 历 程 分 层 原 理 基 本 概 念 2 发 展 历 程 网 络 体 系 结 构 提 出 的 背 景 计 算 机 网 络 的 复 杂 性 异 质 性 不 同 的 通 信 介 质 有 线

More information

PL600 IPPBX 用户手册_V2.0_.doc

PL600 IPPBX 用户手册_V2.0_.doc VoIP 网 络 交 换 机 PL-600 IPPBX 用 户 手 册 深 圳 普 联 讯 电 子 科 技 有 限 公 司 版 权 所 有 2009 深 圳 市 普 联 讯 电 子 科 技 有 限 公 司 第 1 共 1 目 录 1. 前 言...3 2. 安 装 前 准 备...3 3. 硬 件 安 装...4 4. 登 陆 及 一 般 操 作 介 绍...4 5. 基 本 配 置...6 6.

More information

KillTest 质量更高 服务更好 学习资料 半年免费更新服务

KillTest 质量更高 服务更好 学习资料   半年免费更新服务 KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务 Exam : JN0-130 Title : Juniper Juniper Networks Certified Internet Specialist.e(JNCIS-E) Version : Demo 1 / 10 1. Which CLI command is used to set

More information

錄...1 說...2 說 說...5 六 率 POST PAY PREPAY DEPOSIT 更

錄...1 說...2 說 說...5 六 率 POST PAY PREPAY DEPOSIT 更 AX5000 Version 1.0 2006 年 9 錄...1 說...2 說...3...4 說...5 六...6 6.1 率...7 6.2 POST PAY...8 6.3 PREPAY DEPOSIT...9 6.4...10 6.5...11 更...12...12 LCD IC LED Flash 更 兩 RJ11 ( ) DC ON OFF ON 狀 狀 更 OFF 復 狀 說

More information

1 公 司 简 介 2 VRRP 原 理 和 应 用 3 新 产 品 和 创 业 计 划 及 赠 书 活 动

1 公 司 简 介 2 VRRP 原 理 和 应 用 3 新 产 品 和 创 业 计 划 及 赠 书 活 动 RouterOS VRRP 应 用 案 例 Application case ISSUE 1.0 Nanning YONGYI Network Technology Co., Ltd. www.mikrotik.cn www.routeros.com.cn www.routerboard.com.cn 陈 家 迁 CHEN JIA QIAN 手 机 Phone:13077766825 E-MAIL:gx18598@126.com

More information

基于点到点链路的 OSPF 的初始配置

基于点到点链路的 OSPF 的初始配置 基于点到点链路的 OSPF 的初始配置 目录 简介先决条件要求使用的组件规则带有串行接口 IP 地址的点对点链路上的 OSPF 网络图配置带有未编号接口的点对点链路上的 OSPF 网络图配置验证验证带有串行接口 IP 地址的 OSPF 的配置验证带有未编号接口的 OSPF 的配置故障排除相关信息 简介 在高级数据链路控制 (HDLC) 和点对点协议 (PPP) 等点对点链路上, 开放最短路径优先 (OSPF)

More information

PS PS GMM SM.zte.com.

PS PS GMM SM.zte.com. WBUB-010-1 ZXWN PS V0411.zte.com. PS PS GMM SM.zte.com. PS TMSI Packet-Temporary mobile subscriber identification number P-TMSI) GPRS MS P- TMSI 4 BCD 3G TS 23.003 MSC SGSN SGSN P-TMSI 11 MSC TMSI 00 01

More information

BYOD Http Redirect convergence Client (1) 2008R2 NLB( ) (2) NLB Unicast mode switch flooding (arp ) NLB DNS Redirect 1. Round-Robin DNS DNS IP/DNS Cli

BYOD Http Redirect convergence Client (1) 2008R2 NLB( ) (2) NLB Unicast mode switch flooding (arp ) NLB DNS Redirect 1. Round-Robin DNS DNS IP/DNS Cli BYOD 204 2015 GoogleHicloud (Load Balance) Server Load Balance Link Load Balance Server Redirect 1. URL Redirect redirector URL redirect Real Server Client HTTP Real Server Web Client 2 (1) URL Redirect

More information

國際認證介紹.PPT

國際認證介紹.PPT 2009/3/13 : : : Exchange SQL : MCP MCSA MCSE MCTS MCITP MCDBA TCSE 2009/3/13 2 ??? Microsoft CISCO LINUX JAVA??, 2009/3/13 3 100? 24? 2009/3/13 4 ? 2009/3/13 5 ? 2009/3/13 6 ? 2009/3/13 7 ? - 2009/3/13

More information

飞鱼星多WAN防火墙路由器用户手册

飞鱼星多WAN防火墙路由器用户手册 WAN VER: 20110218 Copyright 2002-2011 VOLANS WAN VR4600 VR4900 VR7200 VR7500 VR7600 1.1 1.2 IP 1.3 2.1 2.2 2.2.1 2.2.2 3.1 3.2 3.2.1 3.2.2 3.2.3 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.3 4.3.1 4.3.2

More information

ebook140-9

ebook140-9 9 VPN VPN Novell BorderManager Windows NT PPTP V P N L A V P N V N P I n t e r n e t V P N 9.1 V P N Windows 98 Windows PPTP VPN Novell BorderManager T M I P s e c Wi n d o w s I n t e r n e t I S P I

More information

局域网技术课程设计报告.doc

局域网技术课程设计报告.doc 湖 南 第 一 师 范 学 院 信 息 科 学 与 工 程 学 院 局 域 网 络 设 计 方 案 1 目 录 一 系 统 概 述...6 1 课 程 设 计 目 的 :...6 2 课 程 设 计 要 求 :...6 3 需 求 分 析 :...6 二 系 统 分 析 与 设 计...7 1 拓 扑 图 设 计...7 2 ip, 掩 码 及 vlan 规 划...7 3 物 理 布 线 设 计...8

More information

end to end 7.2 OSI 7 OSI 3 A B 7.2 Packet Routing LAN WAN 7.1.2 141

end to end 7.2 OSI 7 OSI 3 A B 7.2 Packet Routing LAN WAN 7.1.2 141 7 IP IP ARP ICMP IP OSI 3 7.1 7.1.1 7.1 DTE0/1 DCE0/1 DCE0/1 DCE2DCE3 DCE4 7.1 DTE1 DTE2 DCE1 DTE1 DCE2 DCE3 DCE4 MAC DCE2 DCE5 DTE1 DCE1 DCE3 DCE6 DTE2 DCE4 7.1 140 end to end 7.2 OSI 7 OSI 3 A B 7.2

More information

中文朗科AirTrackTM T600 迷你无线路由器用户手册.doc

中文朗科AirTrackTM T600 迷你无线路由器用户手册.doc AirTrack T600 http://www.netac.com.cn Netac Netac AirTrack OnlyDisk Netac Netac Netac http://www.netac.com.cn Netac 800-830-3662 FCC 15 B 1 2 3 4 / FCC 20cm 1 2 3 / / ...1 1.1...1 1.2...1 1.3...1 1.4...3...4

More information

如 果 用 一 句 话 来 概 括,2013 年 职 业 院 校 特 别 是 中 等 职 业 学 校 就 业 持 续 向 好, 并 且 保 持 在 较 高 水 平 2013 年 中 职 学 校 的 毕 业 生 就 业 率 是 96.81%, 是 自 2006 年 来 第 八 年 保 持 在 95%

如 果 用 一 句 话 来 概 括,2013 年 职 业 院 校 特 别 是 中 等 职 业 学 校 就 业 持 续 向 好, 并 且 保 持 在 较 高 水 平 2013 年 中 职 学 校 的 毕 业 生 就 业 率 是 96.81%, 是 自 2006 年 来 第 八 年 保 持 在 95% 教 育 部 职 业 教 育 与 成 人 教 育 司 葛 道 凯 司 长 谈 2014 职 教 热 点 编 者 按 :2014 年 中 国 高 校 毕 业 生 规 模 将 达 到 727 万 人, 相 较 于 2013 年 的 699 万 人, 增 长 28 万 人, 被 称 为 史 上 更 难 就 业 年, 而 职 业 教 育 向 来 是 异 军 突 起, 是 扛 着 高 就 业 的 金 字 招 牌

More information

管理CISCO IOS

管理CISCO IOS 学习沉淀成长分享 WAN, PPP and FrameRelay 红茶三杯微博 :http://t.sina.com/vinsoney Latest update: 2012-06-01 Content 广域网概述 PPP FrameRelay 广域网概述 什么是广域网 广域网链路类型 常见的广域网封装 Local Area Network Si 局域网 (Local Area Network,LAN)

More information

R3105+ ADSL

R3105+ ADSL ... 1 1 1... 1 1 2... 1... 3 2 1... 3 2 2... 3 2 3... 5 2 4... 5 2 4 1... 5... 7 3 1... 7 3 2... 8 3 2 1... 8 3 2 2... 9 3 3... 12 3 3 1... 13 3 3 2 WAN... 16 3 3 3 LAN... 21 3 3 4 NAT... 22 3 3 5... 24

More information