CCNA 講義

Size: px
Start display at page:

Download "CCNA 講義"

Transcription

1 CCNA 筆 記 王 振 民 目 錄 第 1 章 Packet Tracer 的 使 用... 2 第 1 節 安 裝... 2 第 2 節 建 置 網 路 環 境 _01( 二 台 PC+ 一 台 HUB)... 8 第 3 節 Pc 的 設 定 :IP, cmd 第 4 節 傳 送 封 包 (ICMP 封 包 檢 視...) 第 2 章 基 礎 知 識 第 1 節 開 機 流 程 第 2 節 不 同 的 模 式 第 3 節 密 碼 忘 了, 怎 麼 辦? 第 3 章 Router 與 Switch 的 基 本 管 理 第 1 節 基 本 的 操 作 第 2 節 Router 與 Switch 的 管 理 性 組 態 第 3 節 顯 示 系 統 設 定 的 狀 態 第 4 章 管 理 cisco 路 由 器 第 1 節 基 本 說 明 第 5 章 IP 遶 送 第 1 節 遶 送 基 礎 第 2 節 Router 的 路 由 表 第 3 節 IP 遶 送 的 進 階 練 習 第 4 節 靜 態 路 由 第 6 章 動 態 路 由 第 1 節 常 見 路 由 協 定 第 2 節 管 理 性 距 離 -AD 第 3 節 RIP 第 4 節 EIGRP 第 5 節 OSPF 第 7 章 交 換 與 擴 展 樹 協 定 第 1 節 SWITCH 快 速 設 定 筆 記 第 2 節 基 本 概 念 第 3 節 Spanning Tree Protocol- 擴 展 樹 協 定 參 考 書 目 王 振 民 CCNA 筆 記

2 第 1 章 Packet Tracer 的 使 用 學 習 Cisco 的 過 程 中, 我 覺 得 這 些 指 令 不 難, 難 的 是 觀 念 以 及 學 習 的 環 境, 以 我 自 己 為 例, 之 前 學 習 的 困 難 處 就 是 沒 有 設 備 能 實 際 操 作, 而 且,Cisco 的 設 備 不 便 宜, 尤 其 我 們 需 要 完 整 的 網 路 環 境 來 練 習, 又 不 只 是 一 台 二 台 就 能 建 置 足 夠 的 環 境, 因 此, 最 常 的 做 法 就 是 利 用 模 擬 器 來 學 習, 網 路 上 有 其 它 幾 套 模 擬 器 都 不 錯, 而 Packet Tracer 這 套 工 具 軟 體 是 Cisco 出 廠 的, 可 以 提 供 我 們 良 好 的 學 習 環 境 有 了 Packet Tracer 這 套 軟 體, 我 想 信, 很 快 的 你 也 可 以 跨 入 到 Cisco 領 域 裡 第 1 節 安 裝 1. 雙 按 Packet Tracer 程 式 王 振 民 CCNA 筆 記

3 2. 選 擇 I accept the agreement, 按 Next 3. 使 用 預 設 的 路 徑 即 可, 按 Next 即 可 王 振 民 CCNA 筆 記

4 4. 這 是 在 程 式 集 裡 的 名 稱, 也 是 以 預 設 值 即 可, 請 按 Next 5. 我 勾 選 這 二 項, 安 裝 完 成 後, 會 在 桌 面 及 快 捷 列 顯 示 Packet Tracer 的 徢 徑 王 振 民 CCNA 筆 記

5 6. 按 Install 開 始 安 裝 7. 這 是 安 裝 的 過 程, 請 稍 候 王 振 民 CCNA 筆 記

6 8. 安 裝 完 成, 按 Finish 時 會 同 時 啟 動 Packet Tracer 9. 第 一 次 執 行 時 會 顯 示 以 下 對 話 框, 當 我 們 將 Packet Tracer 所 建 立 的 模 擬 環 境 進 行 儲 存 動 作 時, 會 有 一 個 預 設 的 儲 存 目 錄, 這 個 目 錄 是 可 以 修 改 的 日 後 可 以 執 行 Options/Preferences, 重 新 指 定 預 設 的 儲 存 路 徑 10. 如 果 系 統 有 開 啟 防 火 牆, 就 會 顯 示 以 下 的 安 全 性 警 訊, 請 按 解 除 封 鎖 王 振 民 CCNA 筆 記

7 11. 這 就 是 Packet Tracer 的 畫 面 先 認 識 一 下 應 用 軟 體 的 基 本 環 境 ( 功 能 表 工 具 列 工 作 區 設 備 區...) 王 振 民 CCNA 筆 記

8 第 2 節 建 置 網 路 環 境 _01( 二 台 PC+ 一 台 HUB) 1. 先 由 左 下 方 的 設 備 區 拉 出 二 台 電 腦 2. 再 拉 出 一 台 switch, 任 何 一 個 都 可 以 3. 接 著 點 選 Connections 裡 的 Copper Straight-Through 王 振 民 CCNA 筆 記

9 4. 在 PC0 點 一 下, 選 擇 FastEthernet 5. 在 switch 這 裡 再 點 一 次, 選 擇 任 何 一 個 port, 完 成 時, 就 等 於 用 網 路 線 將 PC0 與 switch 連 接 起 來 了 6. 同 樣 的 動 作 再 做 一 次, 由 PC1 連 接 到 switch 之 前 已 經 用 掉 的 port 在 這 裡 就 不 會 看 到 了 7. 完 成 二 台 PC 與 一 台 switch 的 超 小 型 網 路 環 境 王 振 民 CCNA 筆 記

10 第 3 節 Pc 的 設 定 :IP, cmd... 前 述 動 作 是 模 擬 實 體 的 環 境 建 置, 接 下 來, 要 針 對 不 同 的 設 備 做 相 關 的 網 路 設 定 1. 點 選 PC0, 會 看 到 以 下 的 對 話 框 在 Physical 頁 籤 看 到 的 PC0 的 模 擬 狀 置, 那 個 電 源 按 鈕 是 有 作 用 的 哦! 除 了 可 以 開 機 關 機 之 外, 左 方 還 提 供 不 同 的 模 組, 請 隨 意 試 試 看 這 裡 的 操 作 2. 點 選 Config 頁 籤, 這 裡 可 以 讓 我 們 設 定 這 台 電 腦 的 網 路 位 址, 在 Global Settings 這 裡, 我 們 先 設 定 Gateway 王 振 民 CCNA 筆 記

11 3. 點 選 左 方 的 INTERFACE / FastEthernet, 可 以 設 定 IP Address Subnet Mask 4. 請 點 選 PC1, 也 做 類 似 的 設 定 這 是 PC1 的 Gateway 設 定 王 振 民 CCNA 筆 記

12 5. 這 是 PC1 的 IP Address 與 Subnet Mask 的 設 定 6. 點 選 Desktop 頁 籤, 其 中 的 Command Prompt, 這 個 功 能 是 模 擬 在 Windows 系 統 下 的 終 端 機 視 窗 ( 也 就 是 cmd 程 式 ) Web Browser 是 模 擬 一 個 小 型 的 瀏 覽 器 IP Configuration 是 視 窗 介 面 的 網 路 設 定 對 話 框 王 振 民 CCNA 筆 記

13 7. 試 試 看,Ping 另 外 一 台 電 腦, 確 認 看 看 網 路 狀 況 8. 這 是 IP Configuration 的 對 話 框 第 4 節 傳 送 封 包 (ICMP 封 包 檢 視...) 請 跟 我 一 起 操 作 王 振 民 CCNA 筆 記

14 第 2 章 基 礎 知 識 第 1 節 開 機 流 程 Router 設 備 有 幾 個 關 鍵 設 備, 是 和 開 機 流 程 有 關 的 : 1. CPU 2. RAM 3. ROM 4. FLASH 5. NVRAM CPU 也 許 我 們 可 以 將 這 類 設 備 當 做 一 個 embed system, 它 有 CPU RAM, 程 式 在 執 行 時, 也 是 載 入 到 RAM 裡 頭, 在 RAM 裡 頭 執 行 ROM 基 本 的 程 式 也 都 在 rom 裡 頭, 開 機 時 也 有 類 似 電 腦 的 bios 動 作 Rom:post diagnostic, bootstrap program, basic ios image, rom monitor Rom 裡 頭 有 個 basic ios image, 最 簡 單 基 礎 的 ios 檔 案, 可 避 免 ios 壞 掉 時 還 可 以 啟 動 修 復 FLASH 是 存 放 ios image 使 用 的 由 於 router 沒 有 硬 碟, 實 際 上 的 作 業 系 統 (ios) 是 存 放 在 flash rom 裡 的, 它 是 可 以 更 新 的 NVRAM 存 放 startup config file, config register startup config file, 每 次 開 機 時 就 會 讀 取 這 個, 所 有 的 密 碼 及 設 定 都 在 這 裡 config register, 可 做 password recovery, 有 時 候 可 以 跳 過 startup config file, 避 免 載 入 失 敗 的 ios 或 跳 過 密 碼 我 們 所 做 的 設 定, 是 存 放 在 NVRAM 裡 的 就 很 像 dos 裡 autoexec.bat 的 作 用, 每 次 開 機 時,router 都 會 去 讀 取 NVRAM 的 資 料 RAM Ram: execution ios, running config, routing tables, caches 王 振 民 CCNA 筆 記

15 Startup config file 被 讀 取 後, 就 稱 為 running config, 所 以 我 們 在 做 設 定 時, 都 是 設 定 running config, 如 果 硬 體 重 新 啟 動, 這 裡 的 設 定 值 就 會 恢 復 原 startup config 裡 的 設 定 值, 因 此, 如 果 有 需 要 長 久 保 存, 我 們 要 另 外 儲 存 成 為 startup config file 也 就 是 說, 開 機 完 成 後,Router 所 運 行 的 系 統 是 放 在 這 裡, 系 統 所 運 作 的 環 境 設 定 檔 案, 也 是 放 在 這 裡, 我 們 如 果 做 了 任 何 的 設 定, 都 是 修 改 RAM 的 內 容, 我 們 通 常 都 會 再 將 RAM 的 資 料 寫 回 到 NVRAM, 如 果 沒 有 寫 回 到 NVRAM 的 話, 一 旦 重 新 開 機, 之 前 所 做 的 設 定 就 會 不 見 操 作 練 習 請 使 用 Packet Tracer, 建 立 一 個 Router 一 台 電 腦 使 用 console 線 連 接, 點 選 電 腦 圖 示, 使 用 Terminal 連 線, 在 Bits Per Second 部 份 設 定 為 9600, 按 OK 連 線 後, 注 意 觀 看 Router 開 機 的 內 容 由 於 這 是 一 台 還 沒 有 做 任 何 設 定 的 設 備, 第 一 次 會 以 互 動 對 話 的 方 式 建 立 設 定 環 境, 建 議 按 no 跳 過 這 個 動 作, 讓 我 們 以 手 動 的 方 式 來 建 立 整 個 環 境 以 下 幾 個 指 令 大 多 是 在 EXEC 特 權 模 式 下 作 用 的, 可 以 試 著 輸 入 看 看 : 1. enable, 這 個 指 令 可 以 讓 我 們 進 入 EXEC 特 權 模 式 2. exit, 可 以 回 到 一 般 模 式 3. show running-config, 可 以 顯 示 目 前 的 設 定 檔 內 容, 如 果 超 過 一 頁, 按 空 白 鍵 可 以 跳 下 一 頁 4. erase startup-config, 可 以 刪 除 啟 動 設 定 檔 5. reload, 可 以 讓 Router 重 新 載 入 執 行 設 定 檔 王 振 民 CCNA 筆 記

16 第 2 節 不 同 的 模 式 Router 有 幾 個 不 同 的 操 作 模 式 : 1. User mode 2. Privileged mode 3. Setup mode 4. Global Configuration mode 5. Other Configuration mode 6. RXBOOT mode User mode, 一 般 模 式 提 示 符 號 會 是 Router>, 只 能 做 查 詢 的 動 作, 如 果 要 做 設 定, 就 必 須 到 下 一 個 特 權 模 式 Privileged mode, 特 權 模 式 提 示 符 號 是 Router#, 可 以 做 一 些 比 較 詳 細 的 動 作 Setup mode 裝 配 模 式, 是 透 過 一 個 動 作 一 個 動 作 的 詢 問 方 式, 逐 步 的 引 導 我 們 設 定 系 統 一 般 都 建 議 進 入 跟 著 操 作 一 次, 之 後 就 再 也 不 要 用 它, 還 是 以 CLI 的 模 式 為 主 Global Configuration mode 提 示 符 號 是 Router(config)#, 多 了 一 個 config 字 串, 這 是 針 對 全 域 環 境 的 設 定 Other Configuration mode 提 示 符 號 是 Router(config-mode)#, 如 果 有 二 個 介 面 卡, 而 我 們 只 要 單 單 設 定 其 中 一 張 介 面 卡, 就 是 在 這 個 模 式 底 下 操 作 做 RXBOOT mode 開 機 時 按 Ctrl+c, 就 可 以 進 入, 這 是 讓 我 們 做 一 些 緊 急 的 設 定 或 是 做 system recovery 使 用 的 王 振 民 CCNA 筆 記

17 操 作 練 習 請 繼 續 前 項 的 操 作 環 境 來 做 練 習 : 1. 在 privileged mode 下 輸 入 configure 可 以 進 入 config mode, 有 三 個 選 項, 所 以 系 統 會 問 我 們 要 進 入 那 一 個 項 目, 請 選 擇 terminal 這 個 動 作 我 們 也 可 以 直 接 輸 入 configure terminal, 直 接 指 定 選 擇 terminal 2. line console 0 Console 線 的 keyword 是 line, 所 以 這 裡 輸 入 line console 0 雖 然 router 只 有 一 個 console port, 但 在 index 這 裡 還 是 要 指 定 為 0 輸 入 exit 可 以 回 到 前 一 個 項 目 3. interface Ethernet 0 在 config mode 輸 入 interface Ethernet 0 可 以 指 定 要 進 入 第 一 張 網 路 卡 的 設 定 4. end 或 Ctrl-z 可 以 直 接 回 到 privileged mode 5. show running-config show startup-config 若 沒 有 修 改 的 話, 這 二 個 configuration 的 內 容 只 有 前 幾 行 不 同, 其 它 的 會 是 一 樣 的 6. Show version 除 了 可 以 看 到 ios version, 還 可 以 看 到 其 它 很 有 用 的 資 訊 7. show flash Flash rom 裡 存 著 ios image, 所 以 show flash 可 以 看 到 裡 頭 存 的 ios image 8. show interface serial 0 列 出 interface 及 protocol 不 同 狀 態 時, 可 能 的 問 題 和 狀 況 第 二 行 的 狀 況, 可 能 是 encapsulation 的 type 不 同, 這 裡 是 HDLC, 也 許 對 方 是 PPP, 那 就 會 這 樣 王 振 民 CCNA 筆 記

18 第 3 節 密 碼 忘 了, 怎 麼 辦? 如 果 不 知 道 密 碼 的 解 決 動 作 : 1. 連 線, 但 不 知 道 密 碼, 進 不 去 2. router 的 電 源 關 掉 重 開 王 振 民 CCNA 筆 記

19 3. 會 看 到 終 端 機 正 在 開 機, 按 Ctrl+break 中 斷 4. 執 行 confreg 0x2142, 指 定 之 後 開 機 是 由 BXBOOT 啟 動 王 振 民 CCNA 筆 記

20 5. 再 將 router 的 電 源 重 新 啟 動 由 於 跳 過 startup configuration, 所 以 會 自 動 進 入 setup mode, 輸 入 no 跳 過 它 6. 執 行 enable 進 入 privileged mode, 再 執 行 copy start run 讀 出 設 定 內 容 王 振 民 CCNA 筆 記

21 7. 會 發 現 目 前 的 router 名 稱 已 經 改 了, 表 示 設 定 檔 案 已 經 讀 取 出 來 記 得 要 改 密 碼 囉 執 行 configure terminal 進 入 config mode, 執 行 enable secret lab-a 將 密 碼 改 為 lab-a 再 執 行 line console 0, 要 修 改 console 連 線 的 密 碼 執 行 password 123 將 密 碼 改 為 記 得 要 執 行 copy running-config startup-config 將 改 過 的 密 碼 重 新 寫 回 到 startup config 檔 案 以 後 才 有 作 用 最 後 要 再 config mode 執 行 config-register 0x2102, 下 回 重 開 機 時 可 以 正 常 順 序, 讀 取 startup config 內 容 王 振 民 CCNA 筆 記

22 第 3 章 Router 與 Switch 的 基 本 管 理 第 1 節 基 本 的 操 作 當 裝 置 出 現 狀 態 訊 息 之 後, 按 Enter 鍵, 會 顯 示 Router 的 提 示 列, 這 就 是 User mode, 如 下 : Router> 在 User mode 下 輸 入 enable, 會 進 入 為 Privileged mode, 畫 面 動 作 如 下 : Router> Router>enable Router# 會 發 現 它 們 的 提 示 列 的 狀 態 是 不 一 樣 的 要 從 Privileged mode 回 到 User mode, 可 以 輸 入 disable, 畫 面 如 下 : Router> Router>enable Router# Router#disable Router> 要 離 開 控 制 台, 可 以 輸 入 第 1 項 show history 平 常 使 用 up down 鍵, 可 以 切 換 之 前 曾 經 輸 入 過 的 指 令 如 果 要 直 接 顯 示 所 有 指 令 的 話, 輸 入 : Router#show history 預 設 的 情 況 下,history 會 記 錄 20 個 指 令, 我 們 可 以 輸 入 以 下 指 令 檢 查 : Router#show terminal Line 0, Location: "", Type: "" Length: 24 lines, Width: 80 columns // 略 Modem type is unknown. Session limit is not set. 王 振 民 CCNA 筆 記

23 Time since activation: 00:05:55 Editing is enabled. History is enabled, history size is 20. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are none. Allowed output transports are lat pad telnet rlogin lapb-ta mop v120 ssh. Preferred transport is lat. No output characters are padded No special data dispatching characters Router# 要 修 改 history 記 錄 的 指 令 數 量, 可 以 輸 入 以 下 指 令 : Router#terminal history size 30 Router# 第 2 項 show version show version 指 令 可 以 顯 示 系 統 的 硬 體 與 軟 體 版 本 的 資 訊 王 振 民 CCNA 筆 記

24 第 2 節 Router 與 Switch 的 管 理 性 組 態 接 下 來 介 紹 的 幾 個 指 令, 不 會 讓 路 由 器 或 交 換 器 更 快, 但 是 卻 是 管 理 上 必 須 的 一 些 組 態 設 定 第 1 項 hostname 將 每 個 設 備 指 定 一 個 適 當 的 名 稱, 可 以 方 便 我 們 識 別 這 些 設 備 首 先, 必 須 先 執 行 configure terminal 進 入 Global Configuration mode, 修 改 hostname 的 方 式 如 下 : Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#hostname R1 R1(config)# R1(config)#hostname R2 R2(config)# 可 以 隨 時 修 改 設 備 名 稱, 但 比 較 好 的 方 式, 是 以 設 備 所 處 的 相 關 位 置 來 命 名, 將 來 維 護 時, 會 比 較 容 易 知 道 彼 此 間 的 相 關 位 置 在 這 份 講 義 裡, 我 們 可 能 會 使 用 R1 R2 R3 的 命 名 方 式, 比 較 簡 單 一 些 第 2 項 banner 標 題 訊 息 -motd motd 是 message of the day 的 縮 寫, 表 示 每 次 登 入 系 統 時, 都 會 看 到 這 個 訊 息 設 定 的 方 式 如 下 : R2(config)#banner motd x Hello~~ x R2(config)# 王 振 民 CCNA 筆 記

25 輸 入 Ctrl + z 可 以 回 到 環 境, 再 輸 入 exit 就 可 以 登 出 提 示 列, 如 下 : Press RETURN to get started. Hello~~ R2> 當 我 們 按 下 Enter 要 登 入 系 統 時, 就 會 看 到 剛 才 所 設 定 motd 的 訊 息 再 看 一 下 剛 才 的 設 定 動 作 : R2(config)#banner motd x Hello~~ x R2(config)# 底 下 這 麼 做 也 可 以 : R2(config)#banner motd y HELLO!! y R2(config)# 這 樣 子 也 可 以 : R2(config)#banner motd E hello!! E R2(config)# 但 是, 如 果 用 底 下 這 種 方 式, 輸 入 時 不 會 有 錯 誤 訊 息, 但 motd 所 顯 示 的 訊 息 就 會 變 成 h, 而 不 會 看 到 hello!! : R2(config)#banner motd e hello!! e R2(config)# 現 在 應 該 可 以 知 道, 在 banner motd 指 令 的 後 面, 可 以 用 任 何 字 元 當 做 訊 息 的 開 始 與 結 束 的 分 隔 字 元, 但 是 要 避 免 和 訊 息 內 容 相 同 所 以, 一 般 大 多 數 都 使 用 # 做 為 分 隔 字 元, 如 下 : R2(config)#banner motd # hello~~ # 王 振 民 CCNA 筆 記

26 R2(config)# 如 果 要 輸 入 為 多 行 的 訊 息, 可 以 參 考 以 下 的 動 作 : R2(config)#banner motd # Enter TEXT message. End with the character '#'. hello hello hello # R2(config)# 第 3 項 no ip domain lookup 如 果 我 們 輸 入 指 令 時, 不 小 心 輸 入 錯 誤, 又 按 了 enter 鍵 送 出, 例 如 底 下 錯 誤 的 動 作 : Router#shwo Translating "shwo"...domain server ( ) ( ) Translating "shwo"...domain server ( ) % Unknown command or computer name, or unable to find computer address Router# Router 將 它 當 做 是 網 域 名 稱 的 查 詢, 如 果 要 避 免 這 個 狀 況, 可 以 在 configure mode 裡 輸 入 no ip domain lookup, 關 閉 這 個 功 能, 如 下 : Router# 王 振 民 CCNA 筆 記

27 Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#no ip domain lookup Router(config)# Router(config)#exit Router# Router#shwo Translating "shwo" Translating "shwo" % Unknown command or computer name, or unable to find computer address Router# 執 行 no ip domain lookup 指 令 之 後, 對 於 不 小 心 輸 入 錯 誤 的 指 令, 系 統 不 會 嘗 試 做 網 域 名 稱 的 查 詢, 我 們 可 以 很 快 重 新 輸 入 正 確 的 指 令 第 4 項 設 定 密 碼 在 cisco 裡 可 以 設 定 五 個 密 碼 : 1. enable 密 碼 2. enable secret 密 碼 3. 控 制 台 密 碼 4. 輔 助 埠 (aux) 密 碼 5. telnet(vty) 密 碼 其 中 第 1 2 這 二 個 密 碼, 是 當 我 們 在 User mode 輸 入 enable 要 進 入 Privileged mode 時, 系 統 要 求 我 們 輸 入 的 密 碼, 主 要 是 透 過 密 碼 保 護 Privileged mode 王 振 民 CCNA 筆 記

28 另 外 三 個, 分 別 就 是 我 們 由 控 制 台 輔 助 埠 telnet 的 方 式 連 線 時, 要 求 我 們 輸 入 的 密 碼 第 5 項 設 定 enable 密 碼 以 下 動 作 是 設 定 從 User mode 輸 入 enable 要 進 入 為 Privileged mode 時, 要 輸 入 的 密 碼 請 特 別 注 意 中 間 的 二 個 動 作, 前 項 是 未 加 密 的 密 碼, 第 二 個 則 是 加 密 的 密 碼, 為 了 系 統 安 全 考 量, 因 此,cisco 不 建 議 這 二 個 使 用 相 同 的 密 碼 因 此, 最 後 一 個 指 令 將 密 碼 設 定 為 另 一 個, 就 不 會 顯 示 任 何 警 告 的 訊 息 另 外 一 個 要 注 意 的 是, 設 定 了 secret 密 碼 之 後,password 的 密 碼 會 自 動 失 效, 因 此, 建 議 就 直 接 忽 略 password 的 密 碼, 使 用 secret 密 碼 即 可 Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#enable password 123 Router(config)# Router(config)#enable secret 123 The enable secret you have chosen is the same as your enable password. This is not recommended. Re-enter the enable secret. Router(config)# Router(config)#enable secret Router(config)# Router(config)#exit Router# 王 振 民 CCNA 筆 記

29 第 6 項 設 定 line 密 碼 使 用 者 的 密 碼, 有 以 下 三 種 : 1. line aux, 使 用 輔 助 埠 連 線 的 使 用 者 密 碼 2. line console, 使 用 控 制 台 連 線 的 使 用 者 密 碼 3. line vty, 使 用 telnet 連 線 的 使 用 者 密 碼 第 7 項 line console 密 碼 設 定 console 的 密 碼, 必 須 使 用 line console 0 進 入 console 介 面 裡 做 設 定 由 於 console 只 有 一 個, 所 以 只 有 一 個 數 字 是 0 使 用 password 設 定 密 碼 之 後, 必 須 執 行 login 啟 用 才 可 以 另 外 所 執 行 的 exec-timeout 0 0, 前 個 0 表 示 分 鐘, 後 一 個 0 表 示 秒, 這 個 意 思 0 分 0 秒 之 後 登 出 控 制 台, 也 就 是 說 它 不 會 逾 時 不 會 主 動 登 出 控 制 台 預 設 是 10 分 鐘 後 登 出 另 一 個 logging synchronous, 則 是 系 統 顯 示 訊 息 時, 經 常 會 破 壞 畫 面 上 指 令 輸 入 的 樣 子, 因 此, 設 定 這 個 動 作 之 後, 就 算 系 統 顯 示 訊 息, 還 是 會 維 持 指 令 輸 入 列 的 完 整 Router(config)# Router(config)#line console 0 Router(config-line)# Router(config-line)#password 111 Router(config-line)#login Router(config-line)# Router(config-line)#exec-timeout 0 0 Router(config-line)# Router(config-line)#logging synchronous Router(config-line)# Router(config-line)#exit Router(config)#exit 王 振 民 CCNA 筆 記

30 Router# 重 新 按 enter 登 入 系 統 時, 就 會 需 要 我 們 輸 入 user 密 碼, 就 是 前 項 line console 0 所 設 定 的 密 碼 Press RETURN to get started. User Access Verification Password: 第 8 項 line vty 密 碼 設 定 telnet 連 線 的 密 碼, 要 使 用 line vty 的 方 式, 後 面 接 二 個 數 字 分 別 是 vty 連 線 的 第 一 個 號 碼 最 後 一 個 連 線 號 碼, 第 一 個 號 碼 一 定 是 0, 至 於 最 後 一 個 號 碼 是 多 少, 就 依 設 備 等 級 的 不 同, 可 能 會 不 一 樣, 請 按? 查 詢 就 知 道 了 一 般 來 說, 在 很 多 書 上, 都 會 使 用 line vty 0 4 的 範 圍, 設 定 五 個 連 線 範 圍 的 密 碼, 實 務 上, 應 該 是 全 部 都 設 定 密 碼 會 比 較 好 一 些 Router(config)#line vty? <0-903> First Line number Router(config)#line vty 0? <1-903> Last Line number <cr> Router(config)#line vty 0 4 王 振 民 CCNA 筆 記

31 Router(config-line)# Router(config-line)#password 222 Router(config-line)# Router(config-line)#login Router(config-line)# Router(config-line)#exit Router(config)#exit Router# 第 9 項 description- 描 述 設 定 介 面 的 description 的 作 用, 和 設 定 設 備 的 名 稱 類 似, 都 是 為 了 方 便 管 理, 一 看 就 知 道 這 個 介 面 是 在 做 什 麼 的 由 於 是 設 定 介 面 的 描 述, 因 此, 必 須 進 入 到 介 面 的 管 理 模 式 才 行, 操 作 動 作 如 下 : R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#interface fastethernet 0/0 R1(config-if)# R1(config-if)#description Connect to Switch1 R1(config-if)#^Z %SYS-5-CONFIG_I: Configured from console by console R1# 第 10 項 do 命 令 在 User mode 及 Privileged mode, 我 們 可 以 使 用 show 指 令 查 看 系 統 資 訊, 但 是 在 Configuration mode 下 如 果 要 查 看 系 統 資 訊, 每 次 都 要 跳 出 來, 很 麻 煩, 因 此, 我 們 可 以 使 用 do 指 令, 後 面 再 加 上 show... 就 可 以 直 接 查 看 訊 息 例 如 : R1(config)# R1(config)#sh run ^ 王 振 民 CCNA 筆 記

32 % Invalid input detected at '^' marker. R1(config)#do sh run Building configuration... Current configuration : 869 bytes! version 12.4 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption 第 11 項 啟 動 介 面 在 一 個 設 備 裡, 可 能 會 有 很 多 個 fastethernet 介 面, 尤 其 是 新 的 路 由 器 或 交 換 器, 可 能 還 會 有 多 個 插 槽, 因 此, 我 們 要 針 對 介 面 做 設 定 時, 必 須 使 用 interface 類 型 插 槽 / 埠 號 的 方 式, 有 些 可 能 更 多, 例 如 序 列 界 面 (serial) 可 能 會 有 三 個 數 字, 表 示 的 方 式 是 interface 類 型 路 由 器 ( 設 備 ) 本 身 / 插 槽 / 埠 號 以 下 的 設 定 動 作, 是 以 這 個 例 子 做 為 參 考 以 下 是 設 定 fastethernet 的 例 子 : R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#interface fastethernet 0/0 R1(config-if)# 王 振 民 CCNA 筆 記

33 R1(config-if)#ip address R1(config-if)# R1(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config-if)# 以 下 是 設 定 serial 的 例 子 : R1(config-if)#exit R1(config)# R1(config)#interface serial 0/0/0 R1(config-if)# R1(config-if)#ip address R1(config-if)# R1(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down R1(config-if)# R1(config-if)#clock rate R1(config-if)# R1(config-if)#exit R1(config)# 在 另 外 一 個 路 由 器 上 做 同 樣 類 似 的 動 作, 將 fastethernet 及 serial 設 定 完 成, 就 會 發 現 原 本 紅 色 的 燈 號 變 成 綠 色, 可 以 在 路 由 器 ping 另 外 一 個 路 由 器 的 IP 位 址 第 3 節 顯 示 系 統 設 定 的 狀 態 第 1 項 show running-config 最 常 使 用 到 的 又 可 以 看 大 部 份 資 訊 的 指 令 就 是 show running-config 了 R1# R1#show running-config Building configuration... Current configuration : 894 bytes! 王 振 民 CCNA 筆 記

34 version 12.4 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption! hostname R1! enable secret 5 $1$mERr$3HhIgMGBA/9qNmgzccuxv0! spanning-tree mode pvst!! interface FastEthernet0/0 ip address duplex auto speed auto! interface FastEthernet0/1 no ip address duplex auto speed auto shutdown! interface Serial0/0/0 ip address clock rate ! interface Serial0/0/1 no ip address clock rate shutdown! interface Vlan1 no ip address shutdown! ip classless!!! banner motd ^C hello R1 ^C!! 王 振 民 CCNA 筆 記

35 !! line con 0 exec-timeout 0 0 password 123 logging synchronous login line vty 0 4 exec-timeout 0 0 password 123 logging synchronous login line vty 5 15 exec-timeout 0 0 password 123 logging synchronous login!!! end R1# 第 2 項 使 用 pipeline 的 功 能 由 於 running-config 的 內 容 很 多, 顯 示 內 容 時, 可 能 會 需 要 找 尋 一 陣 子, 才 能 找 到 我 們 要 的 資 料, 因 此, 我 們 可 以 在 show running-config 之 後, 再 加 上 管 線 直 接 篩 選 出 我 們 要 的 區 塊 內 容 ( 註 : 這 個 功 能 在 Packet Tracer 裡 無 法 執 行, 如 果 有 實 機 或 是 安 裝 GNS3 模 擬 環 境, 應 該 就 可 以 正 常 操 作 ) 以 下 的 操 作 動 作, 只 顯 示 Serial 埠 區 塊 的 內 容 : R1#show running-config? append append operation Append redirected output to URL (URLs supporting only) begin Begin with the line that matches exclude Exclude lines that match 王 振 民 CCNA 筆 記

36 include Include lines that match redirect Redirect output to URL section tee Filter a section of output Copy output to URL R1#show running-config section Serial interface Serial0/0 no ip address shutdown clock rate interface Serial0/1 no ip address shutdown clock rate interface Serial0/2 no ip address shutdown clock rate interface Serial0/3 no ip address shutdown 王 振 民 CCNA 筆 記

37 clock rate R1# 第 3 項 組 態 設 定 - 儲 存 檢 視 running-config 是 在 DRAM 中 的 組 態 檔 案, 是 運 行 組 態 而 startup-config 是 啟 動 組 態, 是 放 在 NVRAM 之 中 的, 在 router 或 switch 啟 動 時, 會 由 NVRAM 中 讀 取 startup-config 檔 案, 變 成 running-config 至 於 我 們 修 改 的 系 統 設 定, 都 是 針 對 running-config 內 容 做 修 改, 因 此, 我 們 在 檢 視 組 態 檔 案 時, 都 是 執 行 show running-config 的 原 因 也 是 這 樣 也 就 是 說, 如 果 我 們 要 檢 視 啟 動 組 態 檔 案, 就 執 行 show startup-config 通 常, 在 我 們 修 改 running-config 的 組 態 之 後, 只 要 設 定 正 確, 我 們 都 會 將 運 行 組 態 備 份 到 啟 動 組 態, 動 作 如 下 : R1# R1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] R1# 如 果 沒 有 備 份 就 將 設 備 重 啟, 啟 動 時 會 再 由 NVRAM 讀 取 startup-config 內 容, 變 成 DRAM 裡 的 running-config, 之 前 設 定 的 動 作 自 然 就 不 見 囉! 第 4 項 組 態 設 定 - 刪 除 我 們 可 以 執 行 erase startup-config 將 NVRAM 裡 的 組 態 檔 案 清 除, 如 下 : R1#erase startup-config Erasing the nvram filesystem will remove all configuration files! Continue? [confirm] [OK] Erase of nvram: complete %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram R1# 下 回 再 重 新 開 機 時, 因 為 NVRAM 裡 的 startup-config 己 經 被 刪 除, 沒 有 資 料, 也 就 是 還 原 為 預 設 的 狀 態, 全 部 都 要 重 新 開 始 設 定 在 Privileged mode 下 也 可 以 執 行 reload 重 新 載 入 NVRAM 是 空 的 清 況 下, 系 統 會 自 動 詢 問 我 們 要 不 要 進 入 setup mode, 請 回 答 no, 王 振 民 CCNA 筆 記

38 自 己 動 手 做 設 定 第 5 項 show interfaces- 顯 示 界 面 資 訊 在 Privileged mode 輸 入 show interfaces, 可 以 顯 示 所 有 界 面 的 狀 態, 如 果 覺 得 只 想 要 看 單 一 介 面 的 狀 態, 也 可 以 直 接 選 擇 該 界 面, 操 作 如 下 : R1# R1#show interfaces... 略 R1# R1#show interfaces fastethernet 0/0 FastEthernet0/0 is up, line protocol is up (connected) Hardware is Lance, address is f4b.8d01 (bia f4b.8d01) Internet address is /24 MTU 1500 bytes, BW Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00, Last input 00:00:08, output 00:00:05, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 3 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 4 packets output, 116 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out R1# 在 這 些 訊 息 裡, 我 們 應 該 要 能 找 到 介 面 的 IP 位 址 子 網 路 遮 罩 最 大 傳 輸 單 位 (MTU, maximum transmission unit) 頻 寬 (BW, bandwidth, 要 注 意 它 的 單 位 是 kbit 哦 ) 可 靠 度 (reliability 255/255, 其 中 的 255/255 為 1 表 示 良 好 ) 負 載 (txload 1/255, rxload 1/255, 其 中 的 1/255 表 示 負 載 很 小 ) 另 外, 仔 細 比 較 show interfaces fastethernet 0/0 與 show interfaces serial 0/0/0 之 王 振 民 CCNA 筆 記

39 間, 也 可 以 看 到 Encapsulation 這 裡 的 內 容 是 不 太 一 樣 的 每 個 介 面 都 會 統 計 該 界 面 上 的 流 量, 如 果 要 清 除 的 話, 可 以 執 行 以 下 指 令 ( 在 Packet Tracer 裡 無 法 使 用 ): Router#clear counters fastethernet 0/0 Clear "show interface" counters on this interface [confirm] Router# *Mar 1 00:01:23.659: %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet0/0 by console Router# 第 6 項 show ip interface 仔 細 比 較 show interfaces fastethernet 0/0 與 show ip interface fastethernet 0/0 二 個 指 令 的 差 別, 其 中 show interfaces 是 屬 於 顯 示 界 面 資 訊 的 內 容, 而 show ip interface 則 是 顯 示 有 關 第 3 層 的 資 訊, 例 如 IP 位 址 遮 罩 界 面 上 是 否 有 access list 等 資 訊 R1#show interfaces fastethernet 0/0 FastEthernet0/0 is up, line protocol is up (connected) Hardware is Lance, address is f4b.8d01 (bia f4b.8d01) Internet address is /24 MTU 1500 bytes, BW Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00, Last input 00:00:08, output 00:00:05, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns 王 振 民 CCNA 筆 記

40 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out R1# R1# R1#show ip interface fastethernet 0/0 FastEthernet0/0 is up, line protocol is up (connected) Internet address is /24 Broadcast address is Address determined by setup command MTU is 1500 Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP Fast switching turbo vector IP multicast fast switching is disabled IP multicast distributed fast switching is disabled Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Probe proxy name replies are disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled R1# 王 振 民 CCNA 筆 記

41 第 7 項 show ip interface brief 這 個 指 令 非 常 好 用, 可 以 提 供 所 有 界 面 的 概 觀 狀 態, 很 容 易 一 下 就 看 到 我 們 關 心 的 狀 態, 例 如 界 面 是 up 或 down 的 狀 態 R1#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/ YES manual up up FastEthernet0/1 unassigned YES unset administratively down down Serial0/0/ YES manual up up Serial0/0/1 unassigned YES unset administratively down down Vlan1 unassigned YES unset administratively down down R1# 第 8 項 show protocols show protocols 也 是 很 好 用 的 指 令, 它 可 以 顯 示 每 個 界 面 的 第 1 層 第 2 層 的 狀 態, 以 及 該 界 面 的 IP 位 址, 和 show ip interface brief 比 較 起 來 其 實 還 滿 像 的, 只 是 呈 現 的 方 式 不 同 R1#show protocols Global values: Internet Protocol routing is enabled FastEthernet0/0 is up, line protocol is up Internet address is /24 FastEthernet0/1 is administratively down, line protocol is down Serial0/0/0 is up, line protocol is up Internet address is /30 Serial0/0/1 is administratively down, line protocol is down Vlan1 is administratively down, line protocol is down R1# 王 振 民 CCNA 筆 記

42 第 4 章 管 理 cisco 路 由 器 第 1 節 基 本 說 明 第 1 項 開 機 Router 開 機 時, 會 執 行 以 下 系 列 的 步 驟 : 1. 執 行 POST 進 行 硬 體 測 試, 確 認 所 有 元 件 都 可 以 正 常 運 作 2. 由 ROM 讀 取 開 機 區 程 式, 用 來 尋 找 並 載 入 IOS 軟 體, 預 設 尋 找 IOS 的 順 序 是 快 閃 記 憶 體 (flash memory) tftp 伺 服 器 ROM 3. 尋 找 NVRAM 的 組 態 檔 (startup-config) 4. NVRAM 的 組 態 檔 如 果 存 在, 就 將 它 載 入, 成 為 運 行 組 態 檔 (running-config), 如 果 找 不 到, 就 進 入 裝 配 模 式 (setup mode) 第 2 項 檢 視 組 態 暫 存 器 的 內 容 -show version 從 這 裡 可 以 得 知 這 個 Router 的 型 號 是 2800, 它 的 IOS 版 本 是 12.4 的,IOS 檔 案 是 c2800nm-advipservicesk9-mz t1.bin, 以 及 64M 的 記 憶 體 R1#show version Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: Copyright (c) by Cisco Systems, Inc. Compiled Wed 18-Jul-07 06:21 by pt_rel_team ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Copyright (c) 2000 by cisco Systems, Inc. System returned to ROM by power-on System image file is "c2800nm-advipservicesk9-mz t1.bin"... 略 cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Processor board ID JAD05190MTZ ( ) M860 processor: part number 0, mask 49 2 FastEthernet/IEEE interface(s) 王 振 民 CCNA 筆 記

43 2 Low-speed serial(sync/async) network interface(s) 239K bytes of NVRAM K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 R1# 這 裡 標 示 為 藍 色 的 0x2102, 是 這 個 設 備 的 組 態 設 定, 展 開 為 位 元 型 態, 就 可 以 知 道 它 的 第 的 位 元 ( 右 方 第 1 個 位 元 是 第 0 個 位 元 ) 是 1, 是 開 啟 的 每 個 位 元 都 有 它 的 意 義 與 作 用, 這 部 份 請 參 考 書 籍 P.7-5 的 內 容 如 果 第 6 個 位 元 ( 右 方 第 1 個 位 元 是 第 0 個 位 元 ) 也 開 啟 的 話 (0x2142), 代 表 Router 開 機 時 忽 略 NVRAM 的 內 容, 也 就 是 說 不 會 讀 取 startup-config 這 個 實 作 的 練 習, 就 是 前 面 所 介 紹 的 密 碼 忘 了, 怎 麼 辦 章 節 內 容 第 3 項 cdp cdp 是 cisco discovery protocal 的 縮 寫, 表 示 是 cisco 發 現 協 定, 主 要 是 用 來 收 集 本 地 與 遠 端 路 由 器 裝 置 的 資 訊 執 行 show cdp, 如 下 : R1#show cdp Global CDP information: Sending CDP packets every 60 seconds Sending a holdtime value of 180 seconds Sending CDPv2 advertisements is enabled R1# 這 裡 有 timer 與 holdtime 二 個 時 間 的 長 度 可 以 設 定, 設 定 方 式 如 下 : Router# Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#cdp? advertise-v2 CDP sends version-2 advertisements holdtime packets Specify the holdtime (in sec) to be sent in log Log messages generated by CDP 王 振 民 CCNA 筆 記

44 run Enable CDP source-interface Insert the interface's IP in all CDP packets timer sent Specify rate (in sec) at which CDP packets are Router(config)# Router(config)#cdp holdtime? <10-255> Length of time (in sec) that receiver must keep this packet Router(config)# Router(config)#cdp timer? <5-254> Rate at which CDP packets are sent (in sec) Router(config)# 第 4 項 show cdp neighbor 使 用 指 令 show cdp neighbor 可 以 顯 示 鄰 居 的 資 訊 這 個 指 令 很 有 用 處, 如 果 我 們 並 沒 有 網 路 拓 撲 圖 可 以 參 考, 可 以 經 由 這 個 指 令 慢 慢 的 查 出 所 有 router 連 接 的 方 式 埠 鄰 居 的 設 備 型 號 埠... 等, 就 可 以 慢 慢 的 畫 出 組 織 的 網 路 拓 撲 圖 表 了 Router#show cdp neighbors Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater Device ID Local Intrfce Holdtme Capability Platform Port ID Router Ser 0/0 139 R S I 3725 Ser 0/0 王 振 民 CCNA 筆 記

45 Router# 這 個 指 令 所 顯 示 的 欄 位 分 別 表 示 裝 置 ID 本 地 界 面 保 留 期 限 性 態 相 連 接 的 平 台 相 連 接 平 台 的 埠 ID 第 5 項 show cdp neighbors detail 如 果 想 要 看 到 相 鄰 裝 置 的 詳 細 資 訊, 可 以 執 行 show cdp neighbors detail 查 看 Router#show cdp neighbors detail Device ID: Router Entry address(es): IP address: Platform: Cisco 3725, Capabshow cdp entry *ilities: Router Switch IGMP Interface: Serial0/0, Port ID (outgoing port): Serial0/0 Holdtime : 149 sec Version : Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1) Technical Support: Copyright (c) by Cisco Systems, Inc. Compiled Wed 18-Aug-10 07:55 by prod_rel_team advertisement version: 2 王 振 民 CCNA 筆 記

46 VTP Management Domain: '' Router# 第 6 項 show cdp entry * show cdp entry * 和 show cdp neighbors detail 輸 出 的 結 果 差 不 多, 但 是 show cdp entry * 還 可 以 再 延 伸 出 二 個 比 較 特 別 的 指 令, 分 別 如 下 : Router# Router#show cdp entry * protocol Protocol information for Router : IP address: Router# Router#show cdp entry * version Version information for Router : Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1) Technical Support: Copyright (c) by Cisco Systems, Inc. Compiled Wed 18-Aug-10 07:55 by prod_rel_team Router# show cdp entry * protocol 可 以 查 看 相 鄰 裝 置 的 IP 位 址 show cdp entry * version 可 以 查 看 相 鄰 裝 置 的 IOS 版 本 王 振 民 CCNA 筆 記

47 第 7 項 show cdp traffic show cdp traffic 指 令 可 以 顯 示 cdp 的 流 量, 包 含 封 包 數 量 發 生 錯 誤 的 數 量 等 Router#show cdp traffic CDP counters : Total packets output: 122, Input: 117 Hdr syntax: 0, Chksum error: 0, Encaps failed: 0 No memory: 0, Invalid packet: 0, Fragmented: 0 CDP version 1 advertisements output: 0, Input: 0 CDP version 2 advertisements output: 122, Input: 117 Router# 第 8 項 show cdp interface show cdp interface 指 令 可 以 顯 示 界 面 上 的 cdp 狀 態, 如 果 只 要 查 看 單 一 界 面, 也 可 以 輸 入 為 show cdp interface serial 0/0 Router# Router#show cdp interface serial 0/0 Serial0/0 is up, line protocol is up Encapsulation HDLC Sending CDP packets every 60 seconds Holdtime is 180 seconds Router# 王 振 民 CCNA 筆 記

48 第 9 項 cdp enable 裝 置 上 的 cdp 功 能 目 前 預 設 開 啟 的, 不 過, 它 也 可 以 關 閉, 因 此, 如 果 執 行 cdp 指 令 卻 沒 有 任 何 輸 出 的 內 容, 很 有 可 能 是 cdp 被 關 閉 了 底 下 的 操 作, 是 先 將 serial 0/0 的 cdp 功 能 關 閉, 顯 示 關 閉 後 的 show cdp 內 容, 再 重 新 將 它 開 啟, 再 show cdp 的 內 容, 藉 以 比 較 二 者 的 差 別 Router# Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#interface serial 0/0 Router(config-if)# Router(config-if)#no cdp enable Router(config-if)# Router(config-if)#do show cdp int s0/0 Router(config-if)# Router(config-if)#cdp enable Router(config-if)# Router(config-if)#do show cdp int s0/0 Serial0/0 is up, line protocol is up Encapsulation HDLC Sending CDP packets every 60 seconds Holdtime is 180 seconds Router(config-if)# 王 振 民 CCNA 筆 記

49 第 5 章 IP 遶 送 第 1 節 遶 送 基 礎 第 1 項 基 本 網 路 環 境 首 先 使 用 Packet Tracer 建 立 以 下 的 網 路 環 境, 有 關 R0 R1 的 設 定, 請 參 閱 之 前 的 說 明, 進 行 Router 的 設 定 至 於 其 它 的 PC, 請 依 照 目 前 的 環 境, 自 行 配 置 適 當 的 IP 位 址 第 2 項 網 路 連 線 測 試 底 下 是 在 PC0 的 電 腦 上, 我 設 定 的 一 個 IP 位 址 Packet Tracer PC Command Line 1.0 PC>ipconfig IP Address...: Subnet Mask...: 王 振 民 CCNA 筆 記

50 Default Gateway...: PC> 從 PC0 要 能 ping 到 PC1 PC>ping Pinging with 32 bytes of data: Reply from : bytes=32 time=7ms TTL=128 Reply from : bytes=32 time=9ms TTL=128 Reply from : bytes=32 time=4ms TTL=128 Reply from : bytes=32 time=11ms TTL=128 Ping statistics for : Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 4ms, Maximum = 11ms, Average = 7ms PC> 從 PC0 要 能 ping 到 R1 的 FastEthernet 0/0 的 IP 位 址 PC>ping Pinging with 32 bytes of data: Reply from : bytes=32 time=14ms TTL=255 Reply from : bytes=32 time=6ms TTL=255 Reply from : bytes=32 time=9ms TTL=255 Reply from : bytes=32 time=10ms TTL=255 Ping statistics for : Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 6ms, Maximum = 14ms, Average = 9ms PC> 除 了 直 接 連 接 的 R1 FastEthernet0/0 之 外, 還 要 能 夠 ping 到 R1 的 FastEthernet0/1 FastEthernet1/1 位 址 PC>ping 王 振 民 CCNA 筆 記

51 Pinging with 32 bytes of data: Reply from : bytes=32 time=4ms TTL=255 Reply from : bytes=32 time=9ms TTL=255 Reply from : bytes=32 time=2ms TTL=255 Reply from : bytes=32 time=12ms TTL=255 Ping statistics for : Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 12ms, Average = 6ms PC> 而 且, 還 要 能 ping 到 PC2 PC3 PC4 PC5 PC>ping Pinging with 32 bytes of data: Request timed out. Reply from : bytes=32 time=17ms TTL=127 Reply from : bytes=32 time=20ms TTL=127 Reply from : bytes=32 time=13ms TTL=127 Ping statistics for : Packets: Sent = 4, Received = 3, Lost = 1 (25% loss), Approximate round trip times in milli-seconds: Minimum = 13ms, Maximum = 20ms, Average = 16ms PC> 第 2 節 Router 的 路 由 表 第 1 項 show ip route 在 R1 的 Privileged mode 輸 入 show ip route 指 令, 可 以 看 到 router 轉 送 封 包 的 路 由 表 R1#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 王 振 民 CCNA 筆 記

52 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 4 subnets C C C C R1# is directly connected, FastEthernet0/ is directly connected, FastEthernet0/ is directly connected, FastEthernet1/ is directly connected, Serial0/0/0 從 底 下 路 由 表 的 第 一 欄 顯 示 C, 可 以 檢 查 上 方 的 對 照 表, 知 道 它 是 直 接 連 接 的 線 路 因 此, 在 我 們 由 PC0 去 ping 不 同 網 段 的 PC2( XX),router 會 由 這 裡 的 路 由 表 知 道 目 的 地 應 該 是 要 由 FastEthernet0/1 的 連 線 送 出, 這 就 是 路 徑 遶 送 的 方 式 第 2 項 show ip arp 剛 才 有 做 ping 的 動 作, 在 設 備 上 就 會 廣 播 查 詢 IP 位 址 對 映 的 MAC 位 址, 也 會 快 取 起 來, 方 便 下 次 需 要 時 運 用, 我 們 可 以 由 show ip arp 查 到 目 前 快 取 的 IP 與 MAC 的 位 址 R1#show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet D0.970B.BB01 ARPA FastEthernet0/0 Internet AAC.B590 ARPA FastEthernet0/0 Internet C5.3BD4 ARPA FastEthernet0/0 Internet D0.970B.BB02 ARPA FastEthernet0/1 Internet A.F3E0.2C22 ARPA FastEthernet0/1 Internet C8A.A701 ARPA FastEthernet1/0 Internet D C ARPA FastEthernet1/0 R1# 王 振 民 CCNA 筆 記

53 第 3 節 IP 遶 送 的 進 階 練 習 參 照 課 本 P8-17, 建 立 如 下 的 網 路 架 構 圖 第 1 項 設 定 Corp router Router> Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#hostname Corp Corp(config)# Corp(config)#enable secret 123 王 振 民 CCNA 筆 記

54 Corp(config)#no ip domain-lookup Corp(config)#banner motd # this is my Corp 2811 ISR router # Corp(config)# Corp(config)#line console 0 Corp(config-line)#password 123 Corp(config-line)#login Corp(config-line)# Corp(config-line)#logging synchronous Corp(config-line)#exec-timeout 0 0 Corp(config-line)#exit Corp(config)# Corp(config)#line vty 0? <1-15> Last Line number <cr> Corp(config)#line vty 0 15 Corp(config-line)#password 123 Corp(config-line)#login Corp(config-line)#exit Corp(config)# Corp(config)#interface vlan 1 Corp(config-if)#description switch card to core network Corp(config-if)#ip address Corp(config-if)#no shutdown Corp(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up Corp(config-if)# Corp(config-if)#exit Corp(config)# Corp(config)#interface fastethernet 1/0 Corp(config-if)#description switch port connection to WWW server Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up Corp(config-if)# 王 振 民 CCNA 筆 記

55 Corp(config-if)#int f1/1 Corp(config-if)#description switch port connection to server Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet1/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to up Corp(config-if)# Corp(config-if)#int f1/2 Corp(config-if)#description switch port connection to DNS server Corp(config-if)#no shutdown Corp(config-if)# %LINK-5-CHANGED: Interface FastEthernet1/2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/2, changed state to up Corp(config-if)# Corp(config-if)#int s0/0/0 Corp(config-if)#description 1st connection to R1 Corp(config-if)#ip address Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down Corp(config-if)# Corp(config-if)#int s0/0/1 Corp(config-if)#description 2nd connection to R1 Corp(config-if)#ip address Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to down Corp(config-if)# Corp(config-if)#int s0/1/0 Corp(config-if)#description connection to R2 Corp(config-if)#ip address Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/1/0, changed state to down Corp(config-if)# 王 振 民 CCNA 筆 記

56 Corp(config-if)#int f0/0 Corp(config-if)#description connection to R3 Corp(config-if)#ip address Corp(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up Corp(config-if)# Corp(config-if)#^Z Corp# %SYS-5-CONFIG_I: Configured from console by console Corp# Corp#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Corp# 第 2 項 檢 視 Corp 的 routing table Corp# Corp#sh Corp#show ip rou Corp#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 1 subnets C is directly connected, Vlan1 Corp# 王 振 民 CCNA 筆 記

57 第 3 項 設 定 R1 router R1>enable R1#conf R1#configure t R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#hostname R1 R1(config)#enable secret 123 R1(config)#no ip domain-lookup R1(config)#banner motd # this my R1 router # R1(config)# R1(config)#line console 0 R1(config-line)#password 123 R1(config-line)#login R1(config-line)#logging synchronous R1(config-line)#exec-timeout 0 0 R1(config-line)#exit R1(config)# R1(config)#line vty 0? <1-15> Last Line number <cr> R1(config)#line vty 0 15 R1(config-line)#password 123 R1(config-line)#login R1(config-line)# R1(config-line)#exit R1(config)# R1(config)# R1(config)#interface serial 0/0/0 R1(config-if)#description 1st connection to Corp router R1(config-if)#ip address R1(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up R1(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up 王 振 民 CCNA 筆 記

58 R1(config-if)# R1(config-if)#int s0/0/1 R1(config-if)#description 2nd connection to Corp router R1(config-if)#ip address R1(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to up R1(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up R1(config-if)# R1(config-if)#int f0/0 R1(config-if)#description connection to PC0 R1(config-if)#ip address R1(config-if)#no shutdown R1(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R1(config-if)# R1(config-if)#int f0/1 R1(config-if)#description connection to PC1 R1(config-if)#ip address R1(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up R1(config-if)# R1(config-if)#^Z R1# %SYS-5-CONFIG_I: Configured from console by console R1# R1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] R1# 王 振 民 CCNA 筆 記

59 第 4 項 檢 視 R1 的 routing table R1#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 2 subnets C is directly connected, Serial0/0/0 C is directly connected, Serial0/0/1 C /24 is directly connected, FastEthernet0/0 C /24 is directly connected, FastEthernet0/1 R1# 第 5 項 再 次 檢 視 Corp 的 routing table Corp#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set /24 is subnetted, 3 subnets C is directly connected, Vlan1 C is directly connected, Serial0/0/0 C is directly connected, Serial0/0/1 Corp# 王 振 民 CCNA 筆 記

60 第 6 項 設 定 R2 router Router> Router>enable Router# Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#hostname R2 R2(config)#banner motd # this is my R2 router # R2(config)#no ip domain-lookup R2(config)#enable secret 123 R2(config)# R2(config)#line console 0 R2(config-line)#password 123 R2(config-line)#login R2(config-line)#logging synchronous R2(config-line)#exec-timeout 0 0 R2(config-line)#exit R2(config)# R2(config)#line vty 0 15 R2(config-line)#password 123 R2(config-line)#login R2(config-line)#exit R2(config)# R2(config)#interface serial 0/1/0 R2(config-if)#description connection to Corp router R2(config-if)#ip address R2(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/1/0, changed state to up R2(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to up R2(config-if)# R2(config-if)#int f0/0 R2(config-if)#description connection to PC2 R2(config-if)#ip address R2(config-if)#no shutdown 王 振 民 CCNA 筆 記

61 %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R2(config-if)# R2(config-if)#int f0/1 R2(config-if)#description connection to PC3 R2(config-if)#ip address R2(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R2(config-if)# R2(config-if)#^Z %SYS-5-CONFIG_I: Configured from console by console R2# R2#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] R2# 第 7 項 檢 視 R2 的 routing table R2#show ip route /24 is subnetted, 1 subnets C is directly connected, Serial0/1/0 C /24 is directly connected, FastEthernet0/0 C /24 is directly connected, FastEthernet0/1 R2# 第 8 項 檢 視 Corp 的 routing table Corp#show ip route 王 振 民 CCNA 筆 記

62 /24 is subnetted, 4 subnets C is directly connected, Vlan1 C is directly connected, Serial0/0/0 C is directly connected, Serial0/0/1 C is directly connected, Serial0/1/0 Corp# 第 9 項 設 定 R3 router Router> Router>enable Router# Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#hostname R3 R3(config)#banner motd # this is my R3 router # R3(config)#no ip domain-lookup R3(config)#enable secret 123 R3(config)# R3(config)#line console 0 R3(config-line)#password 123 R3(config-line)#login R3(config-line)#logging synchronous R3(config-line)#exec-timeout 0 0 R3(config-line)#exit R3(config)# R3(config)#line vty 0 15 R3(config-line)#password 123 R3(config-line)#login R3(config-line)#exit R3(config)# R3(config)#interface fastethernet 0/0 R3(config-if)#description connection to Corp router R3(config-if)#ip address R3(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up R3(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up 王 振 民 CCNA 筆 記

63 R3(config-if)# R3(config-if)#int f0/1 R3(config-if)#description connection to Laptop0 R3(config-if)#ip address R3(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R3(config-if)# R3(config-if)#^Z R3# %SYS-5-CONFIG_I: Configured from console by console R3# R3#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] R3# 第 10 項 檢 視 R3 的 routing table R3#show ip route /24 is subnetted, 1 subnets C is directly connected, FastEthernet0/ /24 is subnetted, 1 subnets C is directly connected, FastEthernet0/1 R3# 第 11 項 再 次 檢 視 Corp 的 routing table Corp#show ip route /24 is subnetted, 5 subnets C is directly connected, Vlan1 C is directly connected, Serial0/0/0 C is directly connected, Serial0/0/1 王 振 民 CCNA 筆 記

64 C C Corp# is directly connected, Serial0/1/ is directly connected, FastEthernet0/0 第 12 項 將 R3 router 設 定 啟 用 dhcp R3# R3#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip dhcp pool admin R3(dhcp-config)#network R3(dhcp-config)#default-router R3(dhcp-config)#ip name-server R3(dhcp-config)#exit R3(config)# R3(config)#ip dhcp excluded-address R3(config)# R3(config)#exit R3# %SYS-5-CONFIG_I: Configured from console by console R3# 確 認 配 發 出 去 的 IP 位 址, 可 以 執 行 以 下 指 令 : R3# R3#show ip dhcp binding IP address Client-ID/ Lease expiration Type Hardware address E0.8F57.558A -- Automatic R3# 王 振 民 CCNA 筆 記

65 第 4 節 靜 態 路 由 第 1 項 基 本 設 定 語 法 增 加 靜 態 路 由 的 方 式, 是 在 routing table 裡 增 加 一 筆 路 徑, 它 的 語 法 如 下 : ip route 目 的 網 路 遮 罩 下 一 跳 位 址 或 離 開 的 介 面 距 離 permanent 其 中, 距 離 的 選 項, 暫 時 可 以 直 覺 的 當 做 二 個 router 的 距 離, 數 字 越 大 的, 表 示 越 遠, 可 能 越 不 容 易 到 達, 數 字 越 小, 表 示 距 離 越 近, 應 該 越 容 易 到 達 如 果 都 不 做 設 定, 預 設 值 是 1 以 下 二 個 例 子 是 相 同 的 作 用 : ip route ip route s0/0/0 第 2 項 設 定 Corp router 的 靜 態 路 由 先 來 看 看 目 前 Corp router 的 Routing table 的 內 容 : Corp#show ip route /24 is subnetted, 5 subnets C is directly connected, Vlan1 C is directly connected, Serial0/0/0 C is directly connected, Serial0/0/1 C is directly connected, Serial0/1/0 C is directly connected, FastEthernet0/0 Corp# 接 著 進 行 靜 態 路 由 的 設 定 : Corp# Corp#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Corp(config)# Corp(config)#ip route Corp(config)#ip route Corp(config)#ip route Corp(config)#ip route Corp(config)#ip route Corp(config)#exit Corp# %SYS-5-CONFIG_I: Configured from console by console 王 振 民 CCNA 筆 記

Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco

Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco Ch2 Cisco IOS Cisco Cisco Cisco (ROM) (FLASH) (RAM) RAM(NVRAM) Cisco Cisco ROM ROM Cisco ROM(BIOS) ROM 1. POST Cisco 2. BootStrap Cisco IOS 3. IOS IOS IOS Cisco ROM ROM Cisco Flash Flash Flash IOS Cisco

More information

mppp-ddr.pdf

mppp-ddr.pdf DDR 多 链 路 PPP - 基 本 配 置 和 验 证 目 录 简 介 开 始 使 用 前 规 则 先 决 条 件 使 用 的 组 件 多 链 路 PPP 干 什 么 配 置 多 链 路 PPP 命 令 传 统 DDR 拨 号 原 型 (Dialer Profile) 验 证 MPPP 操 作 相 关 信 息 简 介 多 链 路 PPP ( 也 指 MP MPPP MLP 或 多 链 路 ) 提

More information

ch08.PDF

ch08.PDF 8-1 CCNA 8.1 CLI 8.1.1 8-2 8-3 8.1.21600 2500 1600 2500 / IOS 8-4 8.2 8.2.1 A 5 IP CLI 1600 2500 8-5 8.1.2-15 Windows 9598NT 2000 HyperTerminal Hilgraeve Microsoft Cisco HyperTerminal Private Edition (PE)

More information

D. 192.168.5.32 E. 192.168.5.14 答 案 :C 3. 工 作 站 A 配 置 的 IP 地 址 为 192.0.2.24/28. 工 作 站 B 配 置 的 IP 地 址 为 192.0.2.100/28. 两 个 工 作 站 之 间 有 直 通 线 连 接, 两 台

D. 192.168.5.32 E. 192.168.5.14 答 案 :C 3. 工 作 站 A 配 置 的 IP 地 址 为 192.0.2.24/28. 工 作 站 B 配 置 的 IP 地 址 为 192.0.2.100/28. 两 个 工 作 站 之 间 有 直 通 线 连 接, 两 台 CCNP 学 前 测 试 题 都 选 自 官 方 的 全 真 考 试 题, 共 100 道 题 实 际 测 试 选 60 道 题, 同 官 方 正 式 考 题 数 目 基 本 一 致, 因 此 等 于 是 模 拟 考 试, 采 用 网 上 形 式 进 行 测 评 学 前 测 评 目 的 是 为 了 检 验 大 家 对 CCNA 阶 段 知 识 掌 握 的 程 度, 同 时 对 CCNA 最 核 心

More information

Microsoft Word - CCNA2_Exploration_instructor_40_CoverSheet.DOC

Microsoft Word - CCNA2_Exploration_instructor_40_CoverSheet.DOC 本 文 档 是 Cisco Systems, Inc. 的 专 有 财 产, 为 Cisco Networking Academy 讲 授 CCNA Exploration 路 由 协 议 和 概 念 课 程 的 教 师 专 用, 允 许 打 印 或 复 制 作 非 商 业 用 途 实 验 1.5.1: 网 络 布 线 和 基 本 路 由 器 配 置 ( 教 师 版 ) 拓 扑 图 地 址 分 配

More information

12.pdf

12.pdf 对 帧 中 继 配 置 与 故 障 排 除 的 全 面 的 指 南 交 互 : 本 文 档 对 您 的 Cisco 设 备 进 行 自 定 义 分 析 目 录 简 介 开 始 使 用 前 规 则 先 决 条 件 使 用 的 组 件 背 景 理 论 配 置 基 本 的 帧 中 继 网 络 图 配 置 debug 和 show 命 令 配 置 星 形 帧 中 继 网 络 图 配 置 显 示 命 令 分

More information

F5270

F5270 Cisco 路 由 器 設 定 主 講 : 陳 建 民 本 章 提 要 4-1 Cisco 路 由 器 使 用 者 界 面 4-2 命 令 列 界 面 4-3 路 由 器 與 交 換 器 的 管 理 功 能 4-4 路 由 器 界 面 4-5 檢 視 儲 存 與 清 除 組 態 設 定 2 Cisco 路 由 器 3 4 5 6 Router physical characteristics 7 4-1

More information

epub

epub 3 Cisco 3.1 S e t u p C i s c o C i s c o Cisco IOS C i s c o 3.2 Te l n e t T F T P 3-1 3-1 configure terminal configure memory Configure network t e l n e t < C t r l - Z > conf t N V R A M T F T P I

More information

IP505SM_manual_cn.doc

IP505SM_manual_cn.doc IP505SM 1 Introduction 1...4...4...4...5 LAN...5...5...6...6...7 LED...7...7 2...9...9...9 3...11...11...12...12...12...14...18 LAN...19 DHCP...20...21 4 PC...22...22 Windows...22 TCP/IP -...22 TCP/IP

More information

Procedural Lab Template, Student Version, Required Components

Procedural Lab Template, Student Version, Required Components 拓 樸 圖 位 址 配 置 表 設 備 介 面 IP 位 址 子 網 路 遮 罩 預 設 閘 道 R1 Fa0/0 192.168.1.1 255.255.255.0 不 適 用 S0/0/0 192.168.2.1 255.255.255.0 不 適 用 R2 Fa0/0 192.168.3.1 255.255.255.0 不 適 用 S0/0/0 192.168.2.2 255.255.255.0

More information

Simulator By SunLingxi 2003

Simulator By SunLingxi 2003 Simulator By SunLingxi sunlingxi@sina.com 2003 windows 2000 Tornado ping ping 1. Tornado Full Simulator...3 2....3 3. ping...6 4. Tornado Simulator BSP...6 5. VxWorks simpc...7 6. simulator...7 7. simulator

More information

TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP

TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP TCP/IP : TCP/IP TCP/IP OSI IP TCP IP IP TCP/IP TCP/IP 1. ASCII EBCDIC Extended Binary-Coded Decimal Interchange Code 2. / (1) (2) Single System Image SSI) (3) I/O (4) 3.OSI OSI Open System Interconnection

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

版权声明

版权声明 SG3124 http://www.utt.com.cn 2000-2008 URL Internet Web EULA EULA UTT HiPER PN 0901-0003-001 DN PR-PMMU-1180.03-PPR-CN-1.0A ...1 1...2 1.1...2 1.2...2 1.3...3 1.4...3 2 1.4.1...3 1.4.2...4...5 2.1...5

More information

一、选择题

一、选择题 计 算 机 网 络 基 础 第 7 章 练 习 思 考 与 认 识 活 动 一 选 择 题 1. 下 面 命 令 中, 用 于 检 查 WINDOWS2000 下 TCP/IP 配 置 信 息 的 是 ( ) A. cmd B. nslookup C. ipconfig D. ping 2. 内 部 网 关 协 议 RIP 是 一 种 广 泛 使 用 的 基 于 距 离 矢 量 算 法 的 协 议

More information

課程大綱

課程大綱 CCNA 筆記 王振民 目錄 第 1 章 Packet Tracer 的使用... 2 第 1 節安裝... 2 第 2 節建置網路環境 _01( 二台 PC+ 一台 HUB)... 8 第 3 節 Pc 的設定 :IP, cmd...... 10 第 4 節傳送封包 (ICMP 封包檢視...)... 13 第 2 章基礎知識... 14 第 1 節開機流程... 14 第 2 節不同的模式...

More information

IP-Routing-05.pdf

IP-Routing-05.pdf RI P R I P - 2 RIP -1 R I P - 2 DV RIP -1 RIP-2 16... RIP-2 RIP-2 RIP -1 R I P - 2 RIP-2 RIP-2 RIP-2 V L S M disc ontiguous addr ess sp ace C I D R Cla ssless In ter -Dom ain Routing 121 1 2 2 IP RIP-2

More information

GPRS IP MODEM快速安装说明

GPRS IP MODEM快速安装说明 GF-3026D CDMA 无 线 路 由 器 用 户 手 册 北 京 嘉 复 欣 科 技 有 限 公 司 地 址 : 北 京 市 海 淀 区 阜 成 路 115 号 北 京 印 象 2 号 楼 213 室 电 话 :86-10-88122130 88153193 88153197 传 真 :86-10-88122129 网 站 :http://www.garefowl.com/ 目 录 一 产 品

More information

ebook140-8

ebook140-8 8 Microsoft VPN Windows NT 4 V P N Windows 98 Client 7 Vintage Air V P N 7 Wi n d o w s NT V P N 7 VPN ( ) 7 Novell NetWare VPN 8.1 PPTP NT4 VPN Q 154091 M i c r o s o f t Windows NT RAS [ ] Windows NT4

More information

工程师培训

工程师培训 .1 TCP/IP TCP/IP 1 .2.2.1 Host 1960 S 1970 S Host Low Speed Lines 1970 S 1980 S pc Server Local Interneting 1980 S 1990 S Branch. pc Branch. WAN Branch. pc pc IBM SNA IBM X.25 2 .2.2 OSI OSI Application

More information

通过动态路由协议实现链路备份

通过动态路由协议实现链路备份 通过动态路由协议实现链路备份 实验名称 通过动态路由协议实现链路备份 实验目的 掌握通过在不同链路上配置不同的路由协议实现链路备份 背景描述 你是公司高级网络管理员, 公司内部有一个很重要的服务器所在网段为 192.168.12.0/24, 平常访问通过 R1,R3 的 OSPF 路由协议, 为了保证该网段随时能够访问, 不能因为链路故障出问题, 要求你实现一个备份冗余的功能, 请给予支持 实现功能

More information

R3105+ ADSL

R3105+ ADSL ... 1 1 1... 1 1 2... 1... 3 2 1... 3 2 2... 3 2 3... 5 2 4... 5 2 4 1... 5... 7 3 1... 7 3 2... 8 3 2 1... 8 3 2 2... 9 3 3... 12 3 3 1... 13 3 3 2 WAN... 16 3 3 3 LAN... 21 3 3 4 NAT... 22 3 3 5... 24

More information

ebook140-9

ebook140-9 9 VPN VPN Novell BorderManager Windows NT PPTP V P N L A V P N V N P I n t e r n e t V P N 9.1 V P N Windows 98 Windows PPTP VPN Novell BorderManager T M I P s e c Wi n d o w s I n t e r n e t I S P I

More information

財金資訊-80期.indd

財金資訊-80期.indd IPv6 / LINE YouTube TCP/IP TCP (Transmission Control Protocol) IP (Internet Protocol) (node) (address) IPv4 168.95.1.1 IPv4 1981 RFC 791 --IP IPv4 32 2 32 42 IP (Internet Service Provider ISP) IP IP IPv4

More information

¶C¶L§§¬_™¨ A.PDF

¶C¶L§§¬_™¨ A.PDF 1 9 3 1 9 4 / 7.1 / 1 9 5 7.2 % netstat -rn Routing tables Destination Gateway Flags Refcnt Use Interface 127.0.0.1 127.0.0.1 UH 1 132 lo0 172.16.12.0 172.16.12.2 U 26 49041 le0 1 9 6 / % ping -s almond

More information

ebook20-8

ebook20-8 8 Catalyst 5000 7 V L A N C a t a l y s t V L A N V L A N 8.1 VLAN VTP V L A N A VLAN VLAN 10 VLAN 20 VLAN 10 VLAN 20 B VLAN VLAN 10 VLAN 20 VLAN 10 C VLAN VLAN 10 VLAN 20 VLAN 10 VLAN 20 8-1 VLAN 8 Catalyst

More information

计算机网络概论

计算机网络概论 1 repeater bridge router gateway V.S OSI Repeater(Hub) 1 Repeater 2 3 ( Hub 4 Bridge 1 Bridge 2 N N DL1 DL1 DL2 DL2 Ph1 Ph1 Ph2 Ph2 1 2 Bridge 3 MAC Ethernet FDDI MAC MAC Bridge 4 5 6 7 50873EA6, 00123456

More information

IS-IS路由协议中文教程v1

IS-IS路由协议中文教程v1 IS-IS v1.0 Chapter 0 Preface Statement BSCI Building Scalable Cisco Internetworks Configuring IS-IS Protocol IS-IS IS-IS OSI TCP/IP IS-IS OSPF Cisco System BSCI Student Guide Outline 1 OSI IS-IS 2 IS-IS

More information

Symantec™ Sygate Enterprise Protection 防护代理安装使用指南

Symantec™ Sygate Enterprise Protection 防护代理安装使用指南 Symantec Sygate Enterprise Protection 防 护 代 理 安 装 使 用 指 南 5.1 版 版 权 信 息 Copyright 2005 Symantec Corporation. 2005 年 Symantec Corporation 版 权 所 有 All rights reserved. 保 留 所 有 权 利 Symantec Symantec 徽 标 Sygate

More information

ebook20-7

ebook20-7 7 Catalyst 5000 Catalyst 5000 Cisco Works for Switched Internetworks (CWSI) C L I C L I G U I C L C W S I C i s c o C W S I C L I I P Te l n e t C L I 9600 8 6 7.1 Catalyst C a t a l y s t Cisco IOS C

More information

ARP ICMP

ARP ICMP ARP ICMP 2 9-1 ARP 9-2 ARP 9-3 ARP 9-4 ICMP 9-5 ICMP 9-6 ICMP 9-7 ICMP 3 ARP ICMP TCP / IP, IP ARP ICMP 3 IP, ARP ICMP IP ARP ICMP 2, 4 9-1 ARP, MAC, IP IP, MAC ARP Address Resolution Protocol, OSI ARP,,

More information

SL2511 SR Plus 操作手冊_單面.doc

SL2511 SR Plus 操作手冊_單面.doc IEEE 802.11b SL-2511 SR Plus SENAO INTERNATIONAL CO., LTD www.senao.com - 1 - - 2 - .5 1-1...5 1-2...6 1-3...6 1-4...7.9 2-1...9 2-2 IE...11 SL-2511 SR Plus....13 3-1...13 3-2...14 3-3...15 3-4...16-3

More information

一.NETGEAR VPN防火墙产品介绍

一.NETGEAR VPN防火墙产品介绍 NETGEAR VPN NETGEAR 6 http://www.netgear.com.cn - 1 - NETGEAR VPN... 4 1.1 VPN...4 1.2 Dynamic Domain Name Service...4 1.3 Netgear VPN...4 Netgear VPN... 6 2.1 FVS318 to FVS318 IKE Main...7 2.1.1 A VPN

More information

02.实验二:虚拟局域网与VLAN间通信

02.实验二:虚拟局域网与VLAN间通信 计算机网络 实验指导 实验二 : 虚拟局域网与 VLAN 间通信 一 实验目的 1 理解交换机的工作原理; 2 掌握交换机的带外管理和带内管理的基本方法; 3 理解虚拟局域网(VLAN) 的基本概念和原理 ; 4 掌握在多台二层交换机间划分虚拟局域网的详细内容和操作命令; 5 掌握 VLAN 间通信的基本原理与配置方法 二 实验学时 2 学时 三 实验类型 综合性 四 实验需求 1 硬件每人配备计算机

More information

Chapter 2

Chapter 2 2 (Setup) ETAP PowerStation ETAP ETAP PowerStation PowerStation PowerPlot ODBC SQL Server Oracle SQL Server Oracle Windows SQL Server Oracle PowerStation PowerStation PowerStation PowerStation ETAP PowerStation

More information

IP Access Lists IP Access Lists IP Access Lists

IP Access Lists IP Access Lists IP Access Lists Chapter 10 Access Lists IP Access Lists IP Access Lists IP Access Lists Security) IP Access Lists Access Lists (Network router For example, RouterA can use an access list to deny access from Network 4

More information

两个串行接口上通过虚拟模板的多链路

两个串行接口上通过虚拟模板的多链路 两个串行接口上通过虚拟模板的多链路 目录 简介先决条件要求使用的组件相关产品规则配置网络图配置验证 show 输出示例故障排除故障排除资源故障排除命令调试输出示例相关信息 简介 多链路 PPP (MLP) 对拨号程序接口 ( 如 ISDN 同步和异步接口 ) 上的负载进行均衡 MLP 对数据包进行分割, 并通过并行电路发送各个片段 这样,MLP 可以提高吞吐量, 并减小系统间的延迟 MLP 提供了一种跨多个逻辑数据链路对数据报进行分割

More information

《计算机网络》实验指导书

《计算机网络》实验指导书 1 实 验 一 网 络 组 建 与 管 理 一. 实 验 目 的 1. 掌 握 平 行 双 绞 线 和 交 叉 双 绞 线 的 制 作 方 法 ( 初 级 ) 2. 掌 握 对 等 网 和 代 理 服 务 器 网 络 的 组 建 ( 初 级 ) 3. 会 用 ipconfig 和 ping 命 令 ( 初 级 ) 4. 掌 握 网 络 中 文 件 夹 共 享 和 打 印 机 共 享 ( 初 级 )

More information

IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG

IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG IC-900W Wireless Pan & Tilt Wireless Pan & Tilt Remote Control / Night Vision FCC ID:RUJ-LR802UWG --------------------------------------------TABLE OF CONTENTS------------------------------------------

More information

untitled

untitled 7.1 7.1.1 IP R1 N N,R1,M IP 1 7.1.2 [Quidway]display ip routing Routing Tables: Destination/Mask proto pref Metric Nexthop Interface 0.0.0.0/0 Static 60 0 120.0.0.2 Serial0 8.0.0.0/8 RIP 100 3 120.0.0.2

More information

KillTest 质量更高 服务更好 学习资料 半年免费更新服务

KillTest 质量更高 服务更好 学习资料   半年免费更新服务 KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务 Exam : JN0-130 Title : Juniper Juniper Networks Certified Internet Specialist.e(JNCIS-E) Version : Demo 1 / 10 1. Which CLI command is used to set

More information

第3章

第3章 本 章 涵 盖 以 下 主 题 全 局 单 播 地 址 路 由 和 子 网 划 分 : 本 节 通 过 与 IPv4 相 比 较, 介 绍 了 IPv6 地 址 IPv4 路 由 的 概 念, 以 及 怎 样 进 行 IPv6 子 网 划 分 IPv6 全 局 单 播 地 址 的 分 配 : 本 节 探 讨 了 怎 样 将 全 局 单 播 地 址 分 配 到 主 机 或 其 他 设 备 上 IPv6

More information

飞鱼星多WAN防火墙路由器用户手册

飞鱼星多WAN防火墙路由器用户手册 WAN VER: 20110218 Copyright 2002-2011 VOLANS WAN VR4600 VR4900 VR7200 VR7500 VR7600 1.1 1.2 IP 1.3 2.1 2.2 2.2.1 2.2.2 3.1 3.2 3.2.1 3.2.2 3.2.3 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.3 4.3.1 4.3.2

More information

(UTM???U_935_938_955_958_959 V2.1.9.1)

(UTM???U_935_938_955_958_959 V2.1.9.1) 192.16 www.sharetech.com.tw UTM 多 功 能 防 火 牆 管 理 者 手 冊 V 2.1.9.1 目 錄 第 一 章 安 裝 與 訊 息... 7 1-1 建 議 的 安 裝 設 定 圖... 8 1-2 軟 體 安 裝 設 定... 9 1-3 首 頁 訊 息... 14 1-4 型 號 與 功 能 對 照 表... 17 第 二 章 系 統 設 定... 19 2-1

More information

ebook140-11

ebook140-11 11 VPN Windows NT4 B o r d e r M a n a g e r VPN VPN V P N V P N V P V P N V P N TCP/IP 11.1 V P N V P N / ( ) 11.1.1 11 V P N 285 2 3 1. L A N LAN V P N 10MB 100MB L A N VPN V P N V P N Microsoft PPTP

More information

AL-MX200 Series

AL-MX200 Series PostScript Level3 Compatible NPD4760-00 TC Seiko Epson Corporation Seiko Epson Corporation ( ) Seiko Epson Corporation Seiko Epson Corporation Epson Seiko Epson Corporation Apple Bonjour ColorSync Macintosh

More information

KillTest 质量更高 服务更好 学习资料 半年免费更新服务

KillTest 质量更高 服务更好 学习资料   半年免费更新服务 KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务 Exam : JN0-100 Title : Juniper Networks Certified Internet Associate (JNCIA-JUNOS) Version : Demo 1 / 10 1. Which major J-Web menu should you use

More information

P4i45GL_GV-R50-CN.p65

P4i45GL_GV-R50-CN.p65 1 Main Advanced Security Power Boot Exit System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 Dec 18 2003 Thu

More information

Session Dan Gill 2 IP WAN WAN? Networker NSC-114 RST-271 NSC-211 : MTBF: MTTR: MTBF MTTR : MTBF? MTTR? MTTR MTTR MTTR MTBF MTTR Mom-and-apple-pie MTBF MTBF (UPS, ) Mom-and-apple-pie Increase MTBF MTBF?

More information

Windows RTEMS 1 Danilliu MMI TCP/IP QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos eco

Windows RTEMS 1 Danilliu MMI TCP/IP QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos eco Windows RTEMS 1 Danilliu MMI TCP/IP 80486 QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos ecos Email www.rtems.com RTEMS ecos RTEMS RTEMS Windows

More information

ARM JTAG实时仿真器安装使用指南

ARM JTAG实时仿真器安装使用指南 ARM JTAG Version 1.31 2003. 11. 12 ARM JTAG ARM JTAG.3 ARM 2.1.4 2.2.4 ARM JTAG 3.1 18 3.2 18 3.2.1 Multi-ICE Server.18 3.2.2 ADS..21 ARM JTAG 4.1 Multi-ICE Server 33 4.1.1 Multi-ICE Server..... 33 4.1.2

More information

第 11 章 互聯網技術 11.1 互聯 網 和 萬 維 網 的 發 展 歷 史 A. 互聯網的發展 互聯網是由 ARPANET 開 始發展的 1969 年 美國國防部高級研究計劃署 (ARPA) 把部分軍事研究所和大 的電腦連接起來 建造了㆒個實驗性的電腦網絡 稱為 ARPANET 並 列 的功能

第 11 章 互聯網技術 11.1 互聯 網 和 萬 維 網 的 發 展 歷 史 A. 互聯網的發展 互聯網是由 ARPANET 開 始發展的 1969 年 美國國防部高級研究計劃署 (ARPA) 把部分軍事研究所和大 的電腦連接起來 建造了㆒個實驗性的電腦網絡 稱為 ARPANET 並 列 的功能 互 聯 網 技 術 在 完 成 這 章 後, 你 將 能 夠 描 述 互 聯 網 的 發 展 歷 史 描 述 萬 維 網 的 發 展 歷 史 了 解 連 接 互 聯 網 的 基 本 概 念 能 夠 連 接 到 互 聯 網 知 道 互 聯 網 如 何 運 作 互 聯 網 是 全 球 網 絡 的 集 合 互 聯 網 (Internet) 是 ㆒ 個 集 合 全 球 許 多 網 絡 ㆒ 起 的 大 型 網

More information

Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10

Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Ác Åé å Serial ATA ( Silicon Image SiI3114) S A T A (1) SATA (2)

More information

ansoft_setup21.doc

ansoft_setup21.doc Cadence Cadence Cadence 1000 (1) (2) CIC (3).. CIC Cadence (a) CIC license license server license CIC license CIC license (b) 2000 Cadence license 92 1 1 license server CIC 92 1 1 Cadence license licenser

More information

Windows 2000 Server for T100

Windows 2000 Server for T100 2 1 Windows 95/98 Windows 2000 3.5 Windows NT Server 4.0 2 Windows DOS 3.5 T200 2002 RAID RAID RAID 5.1 Windows 2000 Server T200 2002 Windows 2000 Server Windows 2000 Server Windows 2000 Server 3.5 for

More information

BYOD Http Redirect convergence Client (1) 2008R2 NLB( ) (2) NLB Unicast mode switch flooding (arp ) NLB DNS Redirect 1. Round-Robin DNS DNS IP/DNS Cli

BYOD Http Redirect convergence Client (1) 2008R2 NLB( ) (2) NLB Unicast mode switch flooding (arp ) NLB DNS Redirect 1. Round-Robin DNS DNS IP/DNS Cli BYOD 204 2015 GoogleHicloud (Load Balance) Server Load Balance Link Load Balance Server Redirect 1. URL Redirect redirector URL redirect Real Server Client HTTP Real Server Web Client 2 (1) URL Redirect

More information

VIDEOJET connect 7000 VJC-7000-90 zh- CHS Operation Manual VIDEOJET connect 7000 zh-chs 3 目 录 1 浏 览 器 连 接 7 1.1 系 统 要 求 7 1.2 建 立 连 接 7 1.2.1 摄 像 机 中 的 密 码 保 护 7 1.3 受 保 护 的 网 络 7 2 系 统 概 述 8 2.1 实 况

More information

epub 30-12

epub 30-12 12 IP I P I P E s t a b l i s h e d I P I P l o c k - a n d - k e y V T Y 12.1 1) 2) D D R 3) 4) 5) 12.2 IP C i s c o 1) I P I P I P 402 CCIE 1 I P 0 0.0.0.0 1 3 150. 1. 1 1 ~ 255 150. 1. 1. 0 2) Inbound

More information

PTS7_Manual.PDF

PTS7_Manual.PDF User Manual Soliton Technologies CO., LTD www.soliton.com.tw - PCI V2.2. - PCI 32-bit / 33MHz * 2 - Zero Skew CLK Signal Generator. - (each Slot). -. - PCI. - Hot-Swap - DOS, Windows 98/2000/XP, Linux

More information

Guide to Install SATA Hard Disks

Guide to Install SATA Hard Disks SATA RAID 1. SATA. 2 1.1 SATA. 2 1.2 SATA 2 2. RAID (RAID 0 / RAID 1 / JBOD).. 4 2.1 RAID. 4 2.2 RAID 5 2.3 RAID 0 6 2.4 RAID 1.. 10 2.5 JBOD.. 16 3. Windows 2000 / Windows XP 20 1. SATA 1.1 SATA Serial

More information

局域网技术课程设计报告.doc

局域网技术课程设计报告.doc 湖 南 第 一 师 范 学 院 信 息 科 学 与 工 程 学 院 局 域 网 络 设 计 方 案 1 目 录 一 系 统 概 述...6 1 课 程 设 计 目 的 :...6 2 课 程 设 计 要 求 :...6 3 需 求 分 析 :...6 二 系 统 分 析 与 设 计...7 1 拓 扑 图 设 计...7 2 ip, 掩 码 及 vlan 规 划...7 3 物 理 布 线 设 计...8

More information

ebook71-13

ebook71-13 13 I S P Internet 13. 2. 1 k p p p P P P 13. 2. 2 1 3. 2. 3 k p p p 1 3. 2. 4 l i n u x c o n f P P P 13. 2. 5 p p p s e t u p 13. 2. 6 p p p s e t u p P P P 13. 2. 7 1 3. 2. 8 C a l d e r a G U I 13.

More information

Bus Hound 5

Bus Hound 5 Bus Hound 5.0 ( 1.0) 21IC 2007 7 BusHound perisoft PC hound Bus Hound 6.0 5.0 5.0 Bus Hound, IDE SCSI USB 1394 DVD Windows9X,WindowsMe,NT4.0,2000,2003,XP XP IRP Html ZIP SCSI sense USB Bus Hound 1 Bus

More information

穨CAS1042快速安速說明.doc

穨CAS1042快速安速說明.doc CAS1042 4 Port 10/100M Switch Internet BroadBand Router IP IP... PC CAS1042 UTP Cable CAS1042 5V / 2.4A 6 1. 2. ADSL Cable Modem 3. CAS1042 4. TCP/IP 5. 6. 1 2 ADSL Modem Cable Modem CAS1042 ) / "LAN

More information

ext-web-auth-wlc.pdf

ext-web-auth-wlc.pdf 使 用 无 线 局 域 网 控 制 器 的 外 部 Web 身 份 验 证 配 置 示 例 目 录 简 介 先 决 条 件 要 求 使 用 的 组 件 规 则 背 景 信 息 外 部 Web 身 份 验 证 过 程 网 络 设 置 配 置 为 来 宾 用 户 创 建 动 态 接 口 创 建 预 先 身 份 验 证 ACL 在 WLC 上 为 来 宾 用 户 创 建 本 地 数 据 库 配 置 外 部

More information

自由軟體教學平台

自由軟體教學平台 NCHC Opensource task force DRBL steven@nchc.gov.tw, c00hkl00@nchc.gov.tw National Center for High-Performance Computing http://www.nchc.gov.tw Jan, 2003 1 2003/1/28 ( ) 09:00-10:30 10:40-12:00 Linux 13:00-14:30

More information

KL DSC DEMO 使用说明

KL DSC DEMO 使用说明 :0755-82556825 83239613 : (0755)83239613 : http://www.kingbirdnet.com EMAIL Good989@163.com 1 1 KB3000 DTU... 3 1.1... 3 1.2... 3 1.3... 3 1.4... 3 2... 4 2.1 GSM/GPRS... 4 2.2... 4 2.3... 5 2.4... 6 2.5...

More information

自由軟體教學平台

自由軟體教學平台 NCHC Opensource task force Steven Shiau steven@nchc.gov.tw National Center for High-Performance Computing Sep 10, 2002 1 Outline 1. 2. 3. Service DHCP, TFTP, NFS, NIS 4. 5. 2 DRBL (diskless remote boot

More information

1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005

1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005 1 o o o CPU o o o o o SQL Server 2005 o CPU o o o o o SQL Server o Microsoft SQL Server 2005 1 1...3 2...20 3...28 4...41 5 Windows SQL Server...47 Microsoft SQL Server 2005 DBSRV1 Microsoft SQL Server

More information

实 验 一 双 绞 线 的 制 作 目 的 要 求 1 了 解 非 屏 蔽 双 绞 线 制 作 的 相 关 标 准 2 掌 握 在 各 种 应 用 环 境 下 非 屏 蔽 双 绞 线 的 作 用 与 制 作 3 掌 握 网 线 线 缆 测 试 仪 的 使 用 实 验 设 备 压 线 钳 测 线 仪

实 验 一 双 绞 线 的 制 作 目 的 要 求 1 了 解 非 屏 蔽 双 绞 线 制 作 的 相 关 标 准 2 掌 握 在 各 种 应 用 环 境 下 非 屏 蔽 双 绞 线 的 作 用 与 制 作 3 掌 握 网 线 线 缆 测 试 仪 的 使 用 实 验 设 备 压 线 钳 测 线 仪 数 据 通 信 与 计 算 机 网 络 实 验 指 导 书 实 验 一 双 绞 线 的 制 作 目 的 要 求 1 了 解 非 屏 蔽 双 绞 线 制 作 的 相 关 标 准 2 掌 握 在 各 种 应 用 环 境 下 非 屏 蔽 双 绞 线 的 作 用 与 制 作 3 掌 握 网 线 线 缆 测 试 仪 的 使 用 实 验 设 备 压 线 钳 测 线 仪 双 绞 线 RJ-45 水 晶 头 实 验

More information

自由軟體教學平台

自由軟體教學平台 NCHC Opensource task force DRBL c00hkl00@nchc.gov.tw, steven@nchc.gov.tw National Center for High-Performance Computing http://www.nchc.gov.tw Dec, 2002 1 Outline 1. 2. DRBL 3. 4. Service DHCP, TFTP, NFS,

More information

專業式報告

專業式報告 IP POWER 9258 1U IP POWER 9258IU 說 : V1.38 : 2006. 08-1 - VER. X.X, FCC CE 1. IP POWER 9258. 2. 9258 3. 9258-2 - 1....4... 9258... 2....5...... 3....6 4....8...... 5....9... PC WINDOWS... 6.... 11 7. IE...

More information

QL1880new2.PDF

QL1880new2.PDF ADSL Modem 1 MODEM 56K MODEM 128K ISDN INTERNET ADSL Modem VOD ADSL ADSL 2 1.1 ADSL 1.2 1.3 KM300A 2.1 2.2 2.3 2.4 2.5 KM300A 2.6 web 2.7 1.1ADSL 1.2 1.3 2.1 ADSL 2.2 ADSL 3 ADSL KM300A ADSL KM300A DIY

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

升 级 过 程 概 述 Cisco 集 中 无 线 网 络 架 构 中,AP 工 作 在 瘦 AP(LAP) 模 式 LAP 关 联 到 无 线 控 制 器 (WLC), 控 制 器 管 理 着 配 置 软 件 升 级 以 及 802.1X 认 证 等 控 制 处 理 ; 此 外, 控 制 器 还

升 级 过 程 概 述 Cisco 集 中 无 线 网 络 架 构 中,AP 工 作 在 瘦 AP(LAP) 模 式 LAP 关 联 到 无 线 控 制 器 (WLC), 控 制 器 管 理 着 配 置 软 件 升 级 以 及 802.1X 认 证 等 控 制 处 理 ; 此 外, 控 制 器 还 本 文 档 将 通 过 以 下 章 节 描 述 如 何 将 胖 AP 升 级 为 瘦 AP, 并 与 WLC 进 行 通 信 : 升 级 过 程 概 述... 3 比 要 条 件... 3 重 要 事 项... 5 升 级 准 备 工 作... 5 基 础 环 境 准 备... 6 使 用 DHCP Option 43 参 数... 7 控 制 器 的 准 备 工 作... 9 升 级 步 骤...

More information

网工新答案

网工新答案 2005 年 5 月 29 日 软 考 2005 年 上 半 年 网 络 工 程 师 上 午 试 题 ( 参 考 答 案 ) ( 特 别 声 明, 此 答 案 只 作 参 考 ) 本 文 是 经 过 三 审 后 的 CIU 网 工 上 午 参 考 答 案 ( 正 确 率 在 92%-95% 之 间, 因 为 种 种 原 因, 不 能 与 标 准 答 案 完 全 相 同, 请 大 家 理 解 ) 如

More information

Exam1

Exam1 学网络技术去鸿鹄论坛命运的改变从技术开始 鸿鹄团队致力于为每一位网络技术爱好者提供帮助 有事您发帖, 斑竹为您跑腿, 给您答疑 CCNA 题库战报交流群 :82327397 欢迎备考 CCNA 的朋友加入, 一起讨论交流, 通过 CCNA 考试! CCNA 最新题库 / 最新战报发布区 : http://om/forum-261-1.html CCNA 考试代号 : 640-802 考试时间 : 中文

More information

穨CAS1042中文手冊.doc

穨CAS1042中文手冊.doc CAS1042 4 port 10/100M Switch Internet BroadBand Router ...1...2...3 5...3 1...3 2 ADSL MODEM CABLE MODEM...4...5 4 TCP/IP...6 Windows 95 / 98 / ME/XP...6 WINDOWS 2000...8 WINDOWS NT 4.0...8...9 ADSL (ADSL

More information

Windows XP

Windows XP Windows XP What is Windows XP Windows is an Operating System An Operating System is the program that controls the hardware of your computer, and gives you an interface that allows you and other programs

More information

untitled

untitled CIU ( ) 2005 ( 9 00 11 30 150 ) 1 2B 2 75 1 75 3 A B C D 4 2B 2005 ( ) 88 89 (88)A 4 B 5 C 6 D 7 (89)A 27 B 28 C 29 D 30 5 29 (88) B (89) C 88 B 89 C ( ) 1 2 (1)A B C. D (2)A B C. D 16M (3) (3)A 16 B 20

More information

專業式報告

專業式報告 IP POWER 9258 IP POWER 9258 說 : V1.38 : 2006. 08-1 - VER. X.X, FCC CE 1. IP POWER 9258. 2. 9258 3. 9258-2 - 1....4... 9258... 2....5...... 3....6 4....7...... 5....8... PC / SERVER.. 6. IE... 11 9258...

More information

KillTest 质量更高 服务更好 学习资料 半年免费更新服务

KillTest 质量更高 服务更好 学习资料   半年免费更新服务 KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务 Exam : JN0-331 Title : SEC,Specialist(JNCIS-SEC) Version : Demo 1 / 10 1. Regarding zone types, which statement is true? A. You cannot assign an

More information

Microsoft Word - Che2_Lab_ _Config-Basic-Router-CLI-Students.doc

Microsoft Word - Che2_Lab_ _Config-Basic-Router-CLI-Students.doc 實驗 5.3.5 使用 IOS CLI 設定路由器基本設定 路由器編號 路由器名稱 Fast Ethernet 0 位址 Serial 0 位址 介面類型 兩個介面的子網路遮罩 路由器 1 R1 172.16.0.1 172.17.0.1 DCE 255.255.0.0 路由器 2 R2 172.18.0.1 172.17.0.2 DTE 255.255.0.0 目標 為路由器設定裝置主機名稱 設定控制台密碼

More information

第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特 网 的 标 准 化 工 作 1.2.4 计 算 机 网 络 在

第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特 网 的 标 准 化 工 作 1.2.4 计 算 机 网 络 在 计 算 机 网 络 ( 第 4 版 ) 课 件 第 1 章 计 算 机 网 络 概 述 郭 庆 北 Ise_guoqb@ujn.edu.cn 2009-02-25 第 1 章 概 述 1.1 计 算 机 网 络 在 信 息 时 代 中 的 作 用 1.2 计 算 机 网 络 的 发 展 过 程 *1.2.1 分 组 交 换 的 产 生 *1.2.2 因 特 网 时 代 *1.2.3 关 于 因 特

More information

注意 :CCNA 动手实验所用的路由器是采用 Cisco IOS Release 15.2(4)M3(universalk9 映像 ) 的 Cisco 1941 集成多业务路由器 (ISR) 所用的交换机是采用 Cisco IOS Release 15.0(2)(lanbasek9 映像 ) 的 C

注意 :CCNA 动手实验所用的路由器是采用 Cisco IOS Release 15.2(4)M3(universalk9 映像 ) 的 Cisco 1941 集成多业务路由器 (ISR) 所用的交换机是采用 Cisco IOS Release 15.0(2)(lanbasek9 映像 ) 的 C 拓扑 地址分配表 设备 接口 IP 地址 子网掩码 默认网关 R1 G0/1 192.168.1.1 255.255.255.0 未提供 S1 VLAN 1 未提供 未提供 未提供 PC-A 网卡 192.168.1.3 255.255.255.0 192.168.1.1 目标 第 1 部分 : 设置拓扑并初始化设备 设置设备以匹配网络拓扑 初始化并重新启动 ( 必要时 ) 路由器和交换机 第 2

More information

C3_ppt.PDF

C3_ppt.PDF C03-101 1 , 2 (Packet-filtering Firewall) (stateful Inspection Firewall) (Proxy) (Circuit Level gateway) (application-level gateway) (Hybrid Firewall) 2 IP TCP 10.0.0.x TCP Any High Any 80 80 10.0.0.x

More information

P4VM800_BIOS_CN.p65

P4VM800_BIOS_CN.p65 1 Main H/W Monitor Boot Security Exit System Overview System Time System Date [ 17:00:09] [Fri 02/25/2005] BIOS Version : P4VM800 BIOS P1.00 Processor Type : Intel (R) Pentium (R) 4 CPU 2.40 GHz Processor

More information

68369 (ppp quickstart guide)

68369 (ppp quickstart guide) Printed in USA 04/02 P/N 68369 rev. B PresencePLUS Pro PC PresencePLUS Pro PresencePLUS Pro CD Pass/Fails page 2 1 1. C-PPCAM 2. PPC.. PPCAMPPCTL 3. DB9D.. STPX.. STP.. 01 Trigger Ready Power 02 03 TRIGGER

More information

Microsoft Word - lab2_4.doc

Microsoft Word - lab2_4.doc 网 络 工 程 实 验 4: 路 由 器 基 本 配 置 第 一 部 分 路 由 器 端 口 配 置 实 验 目 的 1. 熟 悉 路 由 设 备 以 及 了 解 路 由 器 的 常 见 端 口 种 类 ; 2. 掌 握 路 由 器 端 口 的 配 置 方 法 ; 3. 掌 握 观 察 和 调 试 路 由 器 的 基 本 方 法 背 景 知 识 路 由 器 端 口 即 指 路 由 器 与 网 络 中

More information

第 1 部 分 : 检 查 网 络 要 求 在 第 1 部 分 中, 您 将 研 究 使 用 172.16.128.0/17 网 络 地 址 为 拓 扑 图 中 显 示 的 网 络 开 发 VLSM 地 址 方 案 的 网 络 要 求 注 意 : 您 可 以 使 用 Windows 计 算 器 应

第 1 部 分 : 检 查 网 络 要 求 在 第 1 部 分 中, 您 将 研 究 使 用 172.16.128.0/17 网 络 地 址 为 拓 扑 图 中 显 示 的 网 络 开 发 VLSM 地 址 方 案 的 网 络 要 求 注 意 : 您 可 以 使 用 Windows 计 算 器 应 拓 扑 目 标 第 1 部 分 : 检 查 网 络 要 求 第 2 部 分 : 设 计 VLSM 地 址 方 案 第 3 部 分 : 布 线 和 配 置 IPv4 网 络 背 景 / 场 景 可 变 长 度 子 网 掩 码 (VLSM) 旨 在 避 免 浪 费 IP 地 址 使 用 VLSM, 会 对 网 络 多 次 进 行 子 网 划 分 此 过 程 可 重 复 多 次, 从 而 根 据 每 个

More information

UDP 8.2 TCP/IP OSI OSI 3 OSI TCP/IP IP TCP/IP TCP/IP Transport Control Protocol TCP User Datagram Protocol UDP TCP TCP/IP IP TCP TCP/IP TC

UDP 8.2 TCP/IP OSI OSI 3 OSI TCP/IP IP TCP/IP TCP/IP Transport Control Protocol TCP User Datagram Protocol UDP TCP TCP/IP IP TCP TCP/IP TC 8 TCP/IP TCP/IP TCP OSI 8.1 OSI 4 end to end A B FTP OSI Connection Management handshake Flow Control Error Detection IP Response to User s Request TCP/IP TCP 181 UDP 8.2 TCP/IP OSI OSI 3 OSI 3 8.1 TCP/IP

More information

Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c) Windows XP

Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c) Windows XP Serial ATA ( Sil3132)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 10 (5) S A T A... 12 Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS

More information

Packet Tracer实验集

Packet  Tracer实验集 Packet Tracer 1 实验集 Packet Tracer 实验集 姚俊编著 目 录 目 录 第一部分路由器实验... 1 实验 1-1. 路由器的 console 口访问配置... 1 实验 1-2. 路由器的 telnet 访问配置... 5 实验 1-3. CLI 的使用与 IOS 基本命令...8 实验 1-4. 配置文件的管理和 IOS 的管理... 15 实验 1-5. 密码恢复和

More information

管理CISCO IOS

管理CISCO IOS 学习沉淀成长分享 设备管理及 CISCO IOS 基础配置 红茶三杯 ( 朱 SIR) 微博 :http://t.sina.com/vinsoney Latest update: 2012-06-01 Content CISCO 路由器及启动过程 设备管理及 CISCO IOS 介绍 CISCO IOS 路由器基础实验 CISCO 路由器及启动过程 路由器组件 路由器启动过程 路由器组件 接口 内存

More information

ebook 175-1

ebook 175-1 1 / L A N WA N 1.1 1.1.1 2 0 60 70 IBM S N A X. 25 SNA 1974 I B M 3270 1-1 I B M S N A S N A S N A I B M / I B M Advanced Program-to-Program Communication, APPC A d v a n c e d P e e r-to-peer Networking,

More information

ICD ICD ICD ICD ICD

ICD ICD ICD ICD ICD MPLAB ICD2 MPLAB ICD2 PIC MPLAB-IDE V6.0 ICD2 usb PC RS232 MPLAB IDE PC PC 2.0 5.5V LED EEDATA MPLAB ICD2 Microchip MPLAB-IDE v6.0 Windows 95/98 Windows NT Windows 2000 www.elc-mcu.com 1 ICD2...4 1.1 ICD2...4

More information

SAPIDO GR-1733 無線寬頻分享器

SAPIDO GR-1733 無線寬頻分享器 1 版 權 聲 明... 4 產 品 保 固 說 明... 4 保 固 期 限... 4 維 修 辦 法... 5 服 務 條 款... 5 注 意 事 項... 6 低 功 率 電 波 輻 射 性 電 機 管 理 辦 法... 6 CE 標 誌 聲 明... 6 無 線 功 能 注 意 事 項... 6 1 產 品 特 點 介 紹... 7 1.1 LED 指 示 燈 功 能 說 明... 8 1.2

More information

第3章 计算机网络体系结构

第3章  计算机网络体系结构 第 3 章 计 算 机 网 络 体 系 结 构 本 章 内 容 计 算 机 的 网 络 体 系 结 构 网 络 参 考 模 型 五 层 网 络 参 考 模 型 1 3.1 计 算 机 网 络 体 系 结 构 发 展 历 程 分 层 原 理 基 本 概 念 2 发 展 历 程 网 络 体 系 结 构 提 出 的 背 景 计 算 机 网 络 的 复 杂 性 异 质 性 不 同 的 通 信 介 质 有 线

More information

第4章网络层_2_.doc

第4章网络层_2_.doc ( 章 节 专 题 首 页 ) 课 程 名 称 计 算 机 网 络 章 节 专 题 第 4 章 网 络 层 ( 二 ) 1.IP 数 据 报 的 格 式 ; 教 学 目 标 及 基 本 要 求 2. 理 解 子 网 划 分 的 意 义, 掌 握 如 何 划 分 子 网 ; 3. 理 解 超 网 构 造 原 理, 掌 握 构 造 超 网 ; 4. 知 道 网 际 控 制 报 文 协 议 ICMP 及

More information