版本:A0

Size: px
Start display at page:

Download "版本:A0"

Transcription

1 CLD2NA SERIES 嵌入式 104 单板电脑 Embedded 104 Single Board Computer Version:C03

2 声明本手册包含的内容并不代表本公司的承诺, 本公司保留对此手册更改的权利, 且不另行通知 对于任何因安装 使用不当而导致的直接 间接 有意或无意的损坏及隐患概不负责 订购产品前, 请向经销商详细了解产品性能是否符合您的需求 EVOC 是研祥智能科技股份有限公司的注册商标 本手册所涉及到的其他商标, 其所有权为相应的产品厂家所拥有 研祥智能科技股份有限公司 2009, 版权所有, 违者必究 未经许可, 不得以机械 电子或其它任何方式进行复制 安全使用小常识 1. 产品使用前, 务必仔细阅读产品说明书 ; 2. 对未准备安装的板卡, 应将其保存在防静电保护袋中 ; 3. 在从防静电保护袋中拿出板卡前, 应将手先置于接地金属物体上一会儿 ( 比 如 10 秒钟 ), 以释放身体及手中的静电 ; 4. 在拿板卡时, 需佩戴静电保护手套, 并且应该养成只触及其边缘部分的习 惯 ; 5. 为避免人体被电击或产品被损坏, 在每次对主板 板卡进行拔插或重新配 置时, 须先关闭交流电源或将交流电源线从电源插座中拔掉 ; 6. 在需对板卡或整机进行搬动前, 务必先将交流电源线从电源插座中拔掉 ; 7. 对整机产品, 需增加 / 减少板卡时, 务必先拔掉交流电源 ; 8. 当您需连接或拔除任何设备前, 须确定所有的电源线事先已被拔掉 ; 9. 为避免频繁开关机对产品造成不必要的损伤, 关机后, 应至少等待 30 秒后 再开机

3 目录 第一章产品介绍...1 简介...1 机械尺寸 重量与环境...1 典型功耗...2 微处理器...2 芯片组...2 系统内存...2 显示功能...2 网络功能...2 音频功能...2 电源特性...2 扩展总线...3 Watchdog 功能...3 I/O 接口...3 第二章安装说明...4 产品外形尺寸图...4 接口位置示意图...5 主板架构图...6 跳线设置...7 LCD 背光控制接口...8 LED 灯...8 串口...9

4 USB 接口...9 显示接口...10 网络接口...12 多功能接口...12 音频接口...13 GPIO 接口...13 JTAG 接口...14 电源接口...14 CF 接口...15 IDE 接口...16 PC/104 接口...17 PC/104-Plus 接口...18 第三章 BIOS 功能简介...19 简介...19 BIOS 参数设置...19 BIOS 基本功能设置...20 x86 平台下 BIOS 所要管理的系统资源...34 第四章驱动程序安装说明...38 附录...39 Watchdog 编程指引...39 数字 IO 编程指引...41

5 第一章产品介绍 第一章产品介绍简介 CLD2NA 系列是低功耗嵌入式 PC/104-Plus 结构的主板, 主板集成度高 体积小 功能齐全 低功耗, 可广泛应用于各种嵌入式系统中 主要特点如下 : 集成超低功耗 AMD R LX 系列 CPU 在板 512M DDR2 内存 ; 提供了 2 个 10/100Mbps 以太网控制器 ; 采用 LX800 内集成显示芯片, 支持 VGA & 18-bit TFT LCD & 18-bit LVDS 显示 支持 VGA+LVDS,VGA+TFT LCD 双显示功能 支持最高分辨率 1280x800; 1 个标准 IDE 接口, 可选 1 个板载 CF 卡座或 1 个板载 1G NAND FLASH; 支持 4 个串口, 其中 2 个支持 RS232 模式,2 个支持 RS422/RS485 模式 支持 4 个 USB 2.0 接口,PC/104 和 PC/104-Plus 双总线扩展 主板配置采用高度集成设计, 方便用户多方面的嵌入式应用系统, 通过丰富的接口, 可广泛应用于医疗 仪器仪表 智能产品 工业控制和国防交通等各种嵌入式领域 机械尺寸 重量与环境 外形尺寸 :115.6mm( 长 ) 96.9mm( 宽 ) 23.2mm( 高 ) 净重 : 109.7g; 工作环境 : 工作温度 :0 ~+60 ; 可扩展工作温度 :-40 ~+85 ; 湿度 :5%~90%( 非凝结状态 ); 贮存环境 : 温度 :-40 C~85 C ; 湿度 :+20%~90%( 非凝结状态 ); CLD2NA 系列 - 1 -

6 第一章产品介绍 典型功耗 CPU: AMD R LX800/LX /366MHz 内存 :512MB DDR2 0.98A;+5%/-3%; 微处理器 支持 AMD R LX800( 标配 )/LX /366MHz BGA481 CPU 芯片组 采用 AMD R Geode CS5536 芯片 系统内存 板载 512MB DDR2 内存 显示功能 采用 LX800 内集成显示芯片, 支持 VGA TFT LCD 18-bit LVDS 接口 支持 VGA+LVDS 双显示功能, 不支持 VGA+LCD+LVDS 同时显示 支持最高分辨率 1280x800 网络功能 提供 2 个 10/100Mbps 网络接口, 不可支持网络唤醒功能 音频功能 采用 AC 97 音效芯片, 支持 MIC-IN,LINE-IN,SPK-OUT 接口, 提供优质的 声音效果 电源特性 采用 AT 电源, +5V 单电源供电 CLD2NA 系列

7 第一章产品介绍扩展总线提供 1 个 PC/104 插槽, 兼容 ISA 总线标准 提供 1 个 PC/104-Plus 插槽, 兼容 PCI 总线标准 Watchdog 功能 支持 255 级, 可编程按分或秒 ; 支持看门狗超时或复位系统 I/O 接口 提供 4 个串口, 其中 2 支持个 RS-232 模式,2 个支持 RS-422/RS-485 模式选择 ; 1 个 IDE 接口, 支持 2 个 IDE 设备 ; 支持 1 个 CF 卡接口或板载 1G NAND FLASH ( 默认为从设备 ) 可选 ; 提供 2 组 USB2.0 接口, 可转接出 4 个 USB 接口 ; 提供 1 个多功能接口, 支持 1 组 PS/2 键盘鼠标接口,1 个蜂鸣器及 1 个复位按钮 ; 提供 1 个 VGA 接口,1 个 LVDS 接口,1 个 TFT LCD 接口 ; 提供 1 个音频接口 ; 提供 1 个 8 位数字 I/O 接口 CLD2NA 系列 - 3 -

8 第二章安装说明 第二章安装说明 产品外形尺寸图 R 单位 :mm CLD2NA 系列

9 第二章安装说明 接口位置示意图 JTAG1 JLCD1 LCDB1 JP1 JCC1 JP3 J3 JP2 AUDIO1 GPIO1 USB2 USB1 LAN2 LAN1 D8 J1 LCD1 COM3 COM4 J4 VGA1 LVDS1 COM1 COM2 D7 D5 J2 IDE1 JCF1 PWR1 正面 CLD2NA 系列 - 5 -

10 第二章安装说明 CF1 背面 主板架构图 VGA LVDS LCD CRT TFT CPU AMD Geode LX Processor MEMORY BUS FPGA MEMORY BUS DDRII CF Card or 1G flash TFT LCD PCI BUS (33MHz) PC104+ PCI to ISA PC/104 IDE PRIMARY IDE 10 / 100 ETHERNET PORT USB2.0X4 GPIO USB2.0 SMBUS Companion Device AMD Geode CS5536 AC97 AUDIO CODEC 10 / 100 ETHERNET PORT LPC BIOS SIO LEGACY SERIAL*4 KB/MS CLD2NA 系列

11 第二章安装说明 提示 : 如何识别跳线 接口的第一脚 1 观察插头 插座旁边的文字标记, 通常用 1 或加粗的线条或三角符号表示 2 看看背面的焊盘, 通常方型焊盘为第一脚 3 电缆上的红线或其它第一脚标记要与插座的第一脚相接 跳线设置 1. JCC1:CMOS 内容清除 / 保持设置 ( 脚距 :2.0 mm) CMOS 由板上钮扣电池供电 清 CMOS 会导致永久性消除以前系统配置并将其设为原始 ( 工厂设置 ) 系统设置 其步骤 :(1) 关闭计算机, 断开电源 ;(2) 瞬间短接 JCC1 插针 ;(3) 开计算机 ;(4) 启动时按屏幕提示按键进入 BIOS 设置, 重新加载最优缺省值 ;(5) 保存并退出设置 设置方式如下 : 设置 功能 JCC1 1-2 开路正常工作状态 (Default) 1-2 短路清除 CMOS 内容, 所有 BIOS 设置恢复成出厂值 2. JLCD1:LCD 工作电压选择 ( 脚距 :2.0 mm) 不同的 LCD 屏电压可能不同, 本板提供了 3.3V 和 5V 两种电压选择, 当所选择的 LCD 电压与所使用的 LCD 屏的工作电压一致时,LCD 屏才能正常显示 设置方式如下 : 设置 功能 JLCD1 1-2 短路 +3.3V(Default) 2-3 短路 +5V 3. JP3:CF 卡主从选择 ( 脚距 :2.0 mm) 设置功能 JP3 1-2 短路 Master 1-2 开路 Slave(Default) CLD2NA 系列 - 7 -

12 第二章安装说明 4. JCF1:CF 卡电压选择 ( 脚距 :2.0 mm) 设置功能 JCF1 1-2 短路 +3.3V 2-3 短路 +5V(Default) 5. JP1, JP2: 串口模式选择 ( 脚距 :2.0 mm) COM3 COM4 支持 RS-422/RS-485 可选 可通过设置 JP1 和 JP2 来实现模式选择, 具体设置如下 : 模式选择管脚设置 RS-485 RS-422 (Default) JP JP1,JP2 JP 注 : 1-2 表示短路帽的位置 LCD 背光控制接口 管脚 信号名称 1 VCC_LCDBKLT 2 NC LCDB1 3 LCD_BKLTEN ( 脚距 :2.0 mm) 4 GND 注 :VCC_LCDBKLT--- 背光电源, 此脚电流限制在 1A 以下 ; LCD_BKLTEN --- 背光使能, 高有效 LED 灯 LED 功能 D5( 绿色 ) IDE 指示灯 D5,D7,D8 D7( 红色 ) 电源指示灯 D8( 红色 ) FPGA 工作指示灯 CLD2NA 系列

13 第二章安装说明串口本板提供 4 个 2 5Pin 插针串口 ( 脚距 :2.0mm)COM1 COM2 支持 RS-232 模式, COM3 COM4 可通过设置 JP1 JP2 设置选择 RS-422 或 RS-485 工作模式, 默认值是 RS-485 COM3 COM4 在 RS-485 模式下, 支持数据自动收发功能 管脚定义如下 : COM1~COM4 信号名称 管脚 COM1,COM2 COM3,COM4 RS-232 RS-422 RS-485(Default) 1 DCD# TXD- Data- 2 RXD TXD+ Data+ 3 TXD RXD+ NC 4 DTR# RXD- NC 5 GND GND GND 6 DSR# NC NC 7 RTS# NC NC 8 CTS# NC NC 9 RI# NC NC 10 NA NA NA USB 接口 本主板提供两个 2x5Pin( 第 9pin 为空 ) USB 排针接口 可通过转接电缆接出 四个 USB 接口, 其定义如下 : 管脚 信号名称 管脚 信号名称 1 +5V 2 +5V 3 USB1_Data- 4 USB2_Data- USB1,USB2 ( 脚距 :2.0 mm) 5 USB1_Data+ 6 USB2_Data+ 7 GND 8 GND 9 NA 10 GND_CHASSIS CLD2NA 系列 - 9 -

14 第二章安装说明 显示接口 1. VGA 接口 管脚信号名称管脚信号名称 1 VSYNC 2 HSYNC 3 DDCDATA 4 Red VGA1 ( 脚距 :2.0 mm) 5 DDCCLK 6 Green 7 +5V 8 Blue 9 GND 10 GND 注 : 在 WinXP 系统中使用 VGA 接口, 当分辨率为 时, 需要在 BIOS 中设置 VGA 的分辨率为 设置方法如下: 启动时按 DEL 键进入 SETUP 菜单 --- 进入 Chipset 选项 --- 进入 North Bridge Configure 菜单 --- Video Configuration 菜单 ---Flat Panel Resolution 菜单, 将分辨率从默认 改成 bit LVDS 接口 LVDS1 ( 脚距 :2.0 mm) 管脚 信号名称 管脚 信号名称 1 LVDS_D0+ 2 LVDS_D0-3 GND 4 GND 5 LVDS_D1+ 6 LVDS_D1-7 GND 8 GND 9 LVDS_D2+ 10 LVDS_D2-11 GND 12 GND 13 CLK+ 14 CLK- 15 GND 16 GND 17 NC 18 NC 19 VDD 20 VDD CLD2NA 系列

15 第二章安装说明 3. TFT LCD 接口 LCD1 管脚 信号名称 管脚 信号名称 1 +12V 2 +12V 3 GND 4 GND 5 VCC_LCD 6 VCC_LCD 7 ENAVEE 8 GND 9 B0 10 B1 11 B2 12 B3 13 B4 14 B5 15 B6 16 B7 17 G0 18 G1 19 G2 20 G3 21 G4 22 G5 23 G6 24 G7 25 R0 26 R1 27 R2 28 R3 29 R4 30 R5 31 R6 32 R7 33 GND 34 GND 35 CLK 36 VSYNC 37 DE 38 HSYNC 39 GND 40 ENABKL 41 GND 42 NC 43 ENAVDD 44 VCON 注 :ENAVEE:LCD 偏置电压使能 ; ENABKL:LCD 背光使能 ; ENAVDD:LCD 电源使能 ; VCON: 亮度调节 CLD2NA 系列

16 第二章安装说明 网络接口 LAN1,LAN2 为 2 5Pin 的设备插针, 此插针式接口是主板上 10/100Mbps 以太 网接口, 需使用转换电缆将接口信号接到标准插座, 下表给出了接口的管脚定义 管脚 信号名称 管脚 信号名称 1 LED+ 2 LINK_ LED- 3 RX+ 4 RX- 5 ACT_LED- 6 TERMINAL1 7 TERMINAL2 8 GND LAN1,LAN2( 脚距 :2.0 mm) 9 TX+ 10 TX- ACTLED ( 绿色灯 ) 网络活动指示状态 LILED( 黄色灯 ) 网速指示状态 闪烁有数据传输亮 100Mbps 灭无数据传输灭 10Mbps 多功能接口 J4 是一个 2 5Pin 设备插针, 是一个多功能接口, 用于连接键盘 鼠标 蜂鸣器和 Reset, 需要使用随单板电脑配置的多功能接口线连接各接口, 下表给 出了接口的管脚定义 管脚 信号名称 管脚 信号名称 1 SPEAK- 2 +5V 3 Reset 4 GND 5 Keyboard Data 6 Keyboard Clock J4 7 GND 8 Mouse Clock ( 脚距 :2.0 mm) 9 +5V 10 Mouse Data CLD2NA 系列

17 第二章安装说明 音频接口 利用附在主板上的电缆,LOUT 可以连接到耳机或更适合的功率扬声器 MIC_IN 用于连接麦克风输入声音, 下表给出了接口的各管脚定义 管脚 信号名称 管脚 信号名称 1 LOUT_R 2 LOUT_L 3 GND_AUDIO 4 GND_AUDIO 5 LIN_R 6 LIN_L AUDIO1 7 GND_AUDIO 8 GND_AUDIO ( 脚距 :2.0 mm) 9 MIC_IN 10 MIC_P GPIO 接口 本主板提供八路可编程 GPIO 端口, 输入输出可由编程随意控制, 默认为 1,3, 5,7 脚是输入,2,4,6,8 脚是输出 定义如下 : 管脚信号名称管脚信号名称 1 GPIO1 2 GPIO5 3 GPIO2 4 GPIO6 GPIO1 ( 脚距 :2.0 mm) 5 GPIO3 6 GPIO7 7 GPIO4 8 GPIO8 9 GND 10 NC CLD2NA 系列

18 第二章安装说明 JTAG 接口 JTAG1 用于烧写板载 XILINX FPGA 代码 ( 预留接口, 没有上料 ) 管脚 信号名称 1 VCC 2 GND 3 TCK JTAG1 ( 脚距 :2.0 mm) 4 TDO 5 TDI 6 TMS 电源接口 管脚信号名称管脚信号名称 1 GND 2 +5V 3 NC 4 +12V PWR1 ( 脚距 :2.54 mm) 5 NC 6-12V 7 GND 8 +5V 9 GND 10 +5V CLD2NA 系列

19 第二章安装说明 CF 接口 Compact Flash 卡是一种快速存储器, 体积很小, 使用方便, 存储量随所用 的卡变化, 如 128M,256M 等 本板提供了一个 CF 卡插槽 ( 在板的背面, 标识为 CF1) CF 卡插入时只能以一个方向插入 管脚 信号名称 管脚 信号名称 1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS0# 32 CS1# 8 GND 33 VS1# 9 ATASEL# 34 IOR# 10 GND 35 IOW# 11 GND 36 WE# 12 GND 37 IRQ 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 VS2# 16 GND 41 RESET# 17 GND 42 IORDY 18 A2 43 DREQ 19 A1 44 DACK# 20 A0 45 DASP# 21 D0 46 ATA66_DET 22 D1 47 D8 23 D2 48 D9 24 WP/IOCS16# 49 D10 25 CD2# 50 GND CLD2NA 系列

20 第二章安装说明 IDE 接口本板提供一组 2 5Pin( 脚距 :2.0 mm) 设备插针, 安装 IDE 设备时需注意 : 一组 IDE 接口可以连接两台 IDE 设备 : 一个为主设备 (Master), 一个为从设备 (Slave) 设备的连接方法是 : 主设备接在电缆的末端, 从设备接在电缆的中间 (IDE 电缆有红色标示的为第一脚 ) IDE1 管脚 信号名称 管脚 信号名称 1 RESET# 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 Key 21 DREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 IORDY 28 GND 29 DACK# 30 GND 31 IRQ 32 NC 33 DA1 34 ATA66_DET 35 DA0 36 DA2 37 CS1# 38 CS3# 39 LED# 40 GND 41 +5V 42 +5V 43 GND 44 GND CLD2NA 系列

21 第二章安装说明 PC/104 接口 管脚 信号名称 管脚 信号名称 管脚 信号名称 管脚 信号名称 A1 IOCHCK# B1 GND C1 GND D1 GND A2 SD7 B2 RESET C2 SBHE# D2 MEMCS16# A3 SD6 B3 +5V C3 LA23 D3 IOCS16# A4 SD5 B4 IRQ9 C4 LA22 D4 IRQ10 A5 SD4 B5-5V C5 LA21 D5 IRQ11 A6 SD3 B6 DRQ2 C6 LA20 D6 IRQ12 A7 SD2 B7-12V C7 LA19 D7 IRQ15 A8 SD1 B8 SRDY# C8 LA18 D8 IRQ14 A9 SD0 B9 +12V C9 LA17 D9 DACK0# A10 IOCHRDY B10 KEY C10 MEMR# D10 DRQ0 A11 AEN B11 SMEMW# C11 MEMW# D11 DACK5# A12 SA19 B12 SMEMR# C12 SD8 D12 DRQ5 A13 SA18 B13 IOW# C13 SD9 D13 DACK6# A14 SA17 B14 IOR# C14 SD10 D14 DRQ6 A15 SA16 B15 DACK3# C15 SD11 D15 DACK7# A16 SA15 B16 DRQ3 C16 SD12 D16 DRQ7 A17 SA14 B17 DACK1# C17 SD13 D17 +5V A18 SA13 B18 DRQ1 C18 SD14 D18 MASTER# A19 SA12 B19 REFRESH# C19 SD15 D19 GND A20 SA11 B20 BCLK C20 KEY D20 GND A21 SA10 B21 IRQ7 A22 SA9 B22 IRQ6 A23 SA8 B23 IRQ5 A24 SA7 B24 IRQ4 A25 SA6 B25 IRQ3 A26 SA5 B26 DACK2# A27 SA4 B27 TC A28 SA3 B28 BALE A29 SA2 B29 +5V A30 SA1 B30 OSC A31 SA0 B31 GND A32 GND B32 GND CLD2NA 系列

22 第二章安装说明 PC/104-Plus 接口 支持 PCI-104 版本 2.0 接口管脚定义见下表 J3 管脚 信号名称 管脚 信号名称 管脚 信号名称 管脚 信号名称 A1 KEY B1 NC C1 +5V D1 AD0 A2 NC B2 AD2 C2 AD1 D2 +5V A3 AD5 B3 GND C3 AD4 D3 AD3 A4 C/BE0# B4 AD7 C4 GND D4 AD6 A5 GND B5 AD9 C5 AD8 D5 GND A6 AD11 B6 NC C6 AD10 D6 NC A7 AD14 B7 AD13 C7 GND D7 AD12 A8 +3.3V B8 C/BE1# C8 AD15 D8 +3.3V A9 SERR# B9 GND C9 NC D9 PAR A10 GND B10 PERR# C V D10 NC A11 STOP# B V C11 PLOCK# D11 GND A V B12 TRDY# C12 GND D12 DEVSEL# A13 FRAME# B13 GND C13 IRDY# D V A14 GND B14 AD16 C V D14 C/BE2# A15 AD18 B V C15 AD17 D15 GND A16 AD21 B16 AD20 C16 GND D16 AD19 A V B17 AD23 C17 AD22 D V A18 IDSEL0 B18 GND C18 IDSEL1 D18 IDSEL2 A19 AD24 B19 C/BE3# C19 NC D19 IDSEL3 A20 GND B20 AD26 C20 AD25 D20 GND A21 AD29 B21 +5V C21 AD28 D21 AD27 A22 +5V B22 AD30 C22 GND D22 AD31 A23 REQ0# B23 GND C23 REQ1# D23 NC A24 GND B24 REQ2# C24 +5V D24 GNT0# A25 GNT1# B25 NC C25 GNT2# D25 GND A26 +5V B26 CLK0 C26 GND D26 CLK1 A27 CLK2 B27 +5V C27 CLK3 D27 GND A28 GND B28 PIRQD# C28 +5V D28 RESET# A29 +12V B29 PIRQA# C29 PIRQB# D29 PIRQC# A30-12V B30 REQ3# C30 GNT3# D30 GND CLD2NA 系列

23 第三章 BIOS 功能简介 第三章 BIOS 功能简介简介 BIOS(Basic Input and Output System: 基本输入输出系统 ) 固化在 CPU 板上的闪存存储器中, 主要功能包括 : 初始化系统硬件, 设置各系统部件的工作状态, 调整各系统部件的工作参数, 诊断系统各部件的功能并报告故障, 给上层软件系统提供硬件操作控制接口, 引导操作系统等 BIOS 提供用户一个菜单式的人机接口, 方便用户配置各系统参数设置, 控制电源管理模式, 调整系统设备的资源分配等等 正确设置 BIOS 各项参数, 可使系统稳定可靠地工作, 同时也能提升系统的整体性能 不适当的甚至错误的 BIOS 参数设置, 则会使系统工作性能大为降低, 使系统工作不稳定, 甚至无法正常工作 BIOS 参数设置每当系统接通电源, 正常开机后, 便可看见进入 BIOS 设置程序提示的信息 此时 ( 其它时间无效 ), 按下提示信息所指定的按键 ( 通常为 <Del> 键 ) 即可进入 BIOS 设置程序 CMOS 中 BIOS 设置内容被破坏时, 系统也会要求进入 BIOS 设置或选择某种默认设置值 通过 BIOS 修改的所有设置值都保存在系统的 CMOS 存储器中, 该 CMOS 存储器由电池供电, 即使切断外部电源, 其内容也不会丢失, 除非执行清除 CMOS 内容的操作 注意!BIOS 的设置直接影响到电脑的性能, 设置错误的参数将造成电脑的损坏, 甚至不能开机, 请使用 BIOS 内置缺省值来恢复系统正常运行 由于本公司不断研发更新 BIOS, 其设置界面也会略有不同, 以下的画面供您参考, 有可能跟您目前所使用的 BIOS 设置程序不完全相同 CLD2NA 系列

24 第三章 BIOS 功能简介 BIOS 基本功能设置 当 SETUP 程序启动之后, 您可以看到 CMOS Setup Utility 主画面如下 : System Overview Processor Type :AMD Geode LX Speed : 500MHz System Memory Size :231MB BIOS SETUP UTILITY Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit System Time [00:47:55] System Date [Wed 01/02/2009] V02.57 (c)copyright ,American Megatrends, Inc. Main System Time 选择此选项, 用 < + > / < - > 来设置目前的时间 以时 / 分 / 秒的格式来表示 各项目合理的范围是 :Hour/ 时 (00-23), Minute/ 分 (00-59),Second/ 秒 (00-59) System Date 选择此选项, 用 < + > / < - > 来设置目前的日期 以月 / 日 / 年的格式来表示 各项目合理的范围是 :Month/ 月 (Jan.-Dec.), Date/ 日 (01-31),Year/ 年 ( 最大至 2099), Week/ 星期 (Mon.~ Sun.) CLD2NA 系列

25 第三章 BIOS 功能简介 Advanced Advanced Settings BIOS SETUP UTILITY Configure CPU WARNING:Setting wrong values in below sections may cause system to malfunction CPU Configuration IDE Configuration Super IO Configuration ISA I/O Decode Configuration ISA Memory Decode Configuration ISA DDMA Channels Configuration Hardware Health Configuration USB Configuration Power Management Configuration Select Screen Select Item Enter Go to Sub Screen Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. CPU Configuration BIOS SETUP UTILITY CPU Configuration Manufacturer:AMD Brand String:AMD Geode LX Frequency :500MHz Cache L1 :64 KB Cache L2 :128 KB Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc CLD2NA 系列

26 第三章 BIOS 功能简介 IDE Configuration BIOS SETUP UTILITY IDE Configuration Onboard PCI IDE Controller [Primary] Primary IDE Master :[Not Detected] Primary IDE Slave :[Not Detected] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Primary IDE Master/Slave * Type Not Installed: 系统没有检测到 IDE 设备 ; AUTO: 系统开机自动检测 IDE 参数 ; CD/DVD: 用于 ATAPI CDROM; ARMD: 用于各种模拟 IDE 设备 * LBA/Large Mode 用于设置是否支持 LBA 模式 * Block(Multi-sector Transfer) 用于设置是否支持多扇区同时传输的功能 * PIO Mode 用于 PIO 模式设置 * DMA Mode 用于 DMA 模式设置 * S.M.A.R.T 此选项用于设置是否启用硬盘 S.M.A.R.T 功能, 只对支持该功能的硬盘有效 * 32Bit Data Transfer 此选项用于使能 32 位的硬盘访问模式, 可以使硬盘读写速度达到最佳 CLD2NA 系列

27 第三章 BIOS 功能简介 Super IO Configuration BIOS SETUP UTILITY Configure SCH311X Super IO Chipset Floppy A OnBoard Floppy Controller Serial Port1 Address Serial Port1 IRQ Serial Port2 Address Serial Port2 IRQ Serial Port3 Address Serial Port3 IRQ Serial Port4 Address Serial Port4 IRQ [Disabled] [Enabled] [3F8] [IRQ4] [2F8] [IRQ4] [3E8] [IRQ3] [2E8] [IRQ3] Allows BIOS to Enable or Disable Floppy Controller Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. Floppy A 软盘驱动器类型配置 OnBoard Floppy Controller 用于使能软驱控制器 Serial Port 1~4 Address 设定主机板上串口 1~4 的地址 Serial Port 1~4 IRQ 设定主机板上串口 1~4 的 IRQ. Parallel Port Address 设定主机板上并口的地址, 地址缺省值为 378 Parallel Port Mode 设定主机板上并口的模式 Parallel Port IRQ 设定主机板上并口的中断 CLD2NA 系列

28 第三章 BIOS 功能简介 ISA I/O Decode Configuration BIOS SETUP UTILITY Configuration ITE8888 IO Address Decode I/O Space 0 [Enabled] Decode I/O BASE 0 [0100h] Decode I/O Size 0 [128 Bytes] Decode I/O Space 1 [Enabled] Decode I/O BASE 1 [0180h] Decode I/O Size 1 [64 Bytes] Decode I/O Space 2 [Enabled] Decode I/O BASE 2 [01C0h] Decode I/O Size 2 [32 Bytes] Decode I/O Space 3 [Enabled] Decode I/O BASE 3 [0200h] Decode I/O Size 3 [128 Bytes] Decode I/O Space 4 [Enabled] Decode I/O BASE 4 [0279h] Decode I/O Size 4 [16 Bytes] Decode I/O Space 5 [Enabled] Decode I/O BASE 5 [0A79h] Decode I/O Size 5 [16 Bytes] Enables Hardware Health Monitoring Device Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. DECODE I/O Space n DECODE I/O Space n (n=0,1,2,3,4,5) 选项为 Disable 和 Enable( 默认 ), 分别代表关闭和打开对应该地址段 ISA 设备的译码 DECODE I/O Speed n DECODE I/O Speed n(n=0,1,2,3,4,5) 选项为 Subtractive speed, Slow Speed,Medium Speed( 默认 ) 和 Fast Speed, 对应该地址段 ISA 设备的译码速度 CLD2NA 系列

29 第三章 BIOS 功能简介 DECODE I/O BASE ADDR n DECODE I/O BASE ADDR n(n=0,1,2,3,4,5) 表示该段 I/O Space 的基地址, 其选项为 0100h,0200h 和 0300h, 与相应的 DECODE I/O Address Offset n 值相加的和, 为该段译码地址的起始地址 DECODE I/O Address Offset n DECODE I/O Address Offset n(n=0,1,2,3,4,5) 表示该段 I/O Space 地址偏移量, 其默认值为 00, 值范围为 00~FF, 使用 + 与 来调节值 DECODE I/O Size n DECODE I/O Size n(n=0,1,2,3,4,5) 表示译码 I/O Space 空间大小, 其选项为 1,2,4,8,16,32,64,128Byte ISA Memory Decode Configuration BIOS SETUP UTILITY Configuration ITE8888 Memory Address Memory Space 0 [Disabled] Decode Mem Base 0 [D00] Decode Mem Size 0 [64 KB] Memory Space 1 [Disabled] Decode Mem Base 0 [0] Decode Mem Size 0 [32 KB] Memory Space 2 [Disabled] Decode Mem Base 0 [0] Decode Mem Size 0 [32 KB] Memory Space 3 [Disabled] Decode Mem Base 0 [0] Decode Mem Size 0 [32 KB] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc CLD2NA 系列

30 第三章 BIOS 功能简介 DECODE Space n Memory Space n (n=0,1,2,3) 选项为 Disable( 默认 ) 和 Enable, 分别代表关闭和打开对应该地址段 ISA 设备的译码 Decode Mem Base n Memory Address Base n [24:8](n=0,1,2,3) 表示该段 Memory 空间的基地址, 其默认值为 0000, 值范围为 0000~FFFF, 使用 + 与 来调节值 Decode Mem Size n Decode Mem Size 0(n=0,1,2,3) 表示该段 Memory 空间的范围 ISA DDMA Channels Configuration BIOS SETUP UTILITY Configuration ITE8888 Memory Address DDMA Slave Channel 0 [Disabled] DDMA Slave Channel 1 [Disabled] DDMA Slave Channel 2 [Disabled] DDMA Slave Channel 3 [Disabled] DDMA Slave Channel 4 [Disabled] DDMA Slave Channel 5 [Disabled] DDMA Slave Channel 6 [Disabled] DDMA Slave Channel 7 [Disabled] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright ,American Megatrends, Inc. DDMA Slave Channel 0 DDMA Slave Channel 0 (n=0,1,2,3. 7) 选项为 Disable( 默认 ) 和 Enable, 分别代表关闭和打开对应该 ISA 设备的 DMA 端口 CLD2NA 系列

31 第三章 BIOS 功能简介 Hardware Health Configuration BIOS SETUP UTILITY Hardware Health Configuration System Temperature : 34 /93 CPU Temperature : 34 /93 Enables Hardware Health Monitoring Device Vcore : V V3.3 :3.312 V V5.0 : V V12.0 : V VBAT : V Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. System Temperature 当前系统温度, 一般主板上有热敏电阻监测 CPU Temperature 当前 CPU 温度 CPU 的温度由板上的温度传感器监测 Vcore CPU 核心电压 V3.3/ V5.0/V12.0 开关电源输出电压 CLD2NA 系列

32 第三章 BIOS 功能简介 USB Configuration USB Configuration Module Version USB Devices Enabled : BIOS SETUP UTILITY Enables USB host controllers. None USB 1.1 Controller USB 2.0 Controller Legacy USB Support Port 4 Assignment Select Screen [Enabled] Select Item + - Change Field [Enabled] F1 General Help [Auto] F10 Save and Exit ESC Exit [Host Controller] V02.57 (c)copyright , American Megatrends, Inc. USB 1.1 Controller 此选项设置 USB 控制器的开关, 即确定是否支持 USB 控制器 USB 2.0 Controller 此选项用来选择是否支持 USB 2.0 控制器 Legacy USB Support 此选项用于支持传统的 USB 设备 ( 键盘, 鼠标, 存储设备等 ), 当该项设为 Enabled 时, 即使不支持 USB 的操作系统如 DOS 下也能使用 USB 设备 Port 4 Assignment 此选项用于指定 usb 控制器类型 CLD2NA 系列

33 第三章 BIOS 功能简介 Power Management Configuration Power Management Configuration ACPI Aware O/S BIOS SETUP UTILITY [Yes] Select Screen Select Item + - Change Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. ACPI Aware O/S 此选项用于提供 ACPI 模式的支持 Chipset BIOS SETUP UTILITY Advanced Chipset Settings WARNING:Setting wrong values in below sections NorthBridge Configuration Configure DRAM Timing by SPD [Enabled] Internal Graphics Mode [Disabled] Select Screen Internal Graphics Memory [24] Select Item Boot Display Type [Panel+CRT] Enter Go to Sub Screen Flat Panel Resolution [800x600] F1 General Help Flat Panel Data Bus Type [9-24 bits, 1 F10 Save and Exit Hoizontal Sync Polarity [Active / low] ] ESC Exit Vertical Sync Polarity [Active low] SouthBridge Configuration Onboard Audio Controller [Enabled] V02.57 (c)copyright , American Megatrends, Inc CLD2NA 系列

34 第三章 BIOS 功能简介 Configure DRAM Timing by SPD 根据 DRAM 上 SPD 芯片中的时序配置内存控制器, 此处建议使用 Enabled, 手动更改 DRAM 时序可能会因为 DRAM 不支持而不开机 Internal Graphics Mode 此选项用于当接有外部显示设备时, 调整板载显卡的显示模式 Internal Graphics Memory 此选项用于调整板载显卡共享物理内存的大小, 单位是 MB Boot Display Type 此选项用于选择开机默认的显示输出设备 Flat Panel Resolution Flat Panel 分辨率选择项 Flat Panel Data Bus Type Flat Panel 数据总线类型, 此处必须与 Flat Panel 的 Spec 一致 Onboard Audio Controller 该选项用于控制板载声卡打开和关闭 PCIPnP BIOS SETUP UTILITY Advanced PCI/PnP Settings WARNING:Setting wrong values in below sections may cause system to malfunction. IRQ3 [Available] Select Screen IRQ4 [Available] Select Item IRQ5 [Available] + - Change Field IRQ7 [Available] F1 General Help IRQ9 [Available] F10 Save and Exit IRQ10 [Available] ESC Exit IRQ11 [Available] IRQ15 [Available] V02.57 (c)copyright , American Megatrends, Inc CLD2NA 系列

35 第三章 BIOS 功能简介 IRQ3~15 此系列选项用以指定对应 IRQ 号是 PNP 方式还是保留给 ISA 使用 Boot BIOS SETUP UTILITY Boot Settings Quick Boot [Enabled] Select Screen Select Item Quiet Boot [Disabled] Enter Go to Sub Screen Waite For F1 If Error [Enabled] F1 General Help Boot from Embedded WinCE [No] F10 Save and Exit Boot Device Priority ESC Exit 1 st Boot Device [1 st FLOPPY DRIVE] V02.57 (c)copyright , American Megatrends, Inc. Quick Boot 配置在 BIOS 引导期间是否允许跳过某些项的测试, 减少 BIOS 引导时间 Quiet Boot 配置是否显示 OEM LOGO 内容 Wait for F1 If Error 配置在系统出错时是否提示按 F1 键 Boot from Embedded WinCE 此选项用于配置从嵌入式 WinCE 引导 注意 : 此项设为 Yes 时需要确保第一引导设备中有 WinCE 系统核心文件 1st~4th Boot Device 配置系统启动时优先权高低的启动设备 CLD2NA 系列

36 第三章 BIOS 功能简介 Security BIOS SETUP UTILITY Security Settings Supervisor Password :Not Installed User Password :Not Installed Change Supervisor Password Change User Password Install or Change the password Select Screen Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Change User/ Supervisor Password 当按 Change User/ Supervisor Password 后, 在对话框中输入新的密码 后, 此栏会显示用户密码已安装 Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults South Bridge Configuration Exit system setup after saving the changes. Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc CLD2NA 系列

37 第三章 BIOS 功能简介 Save Changes and Exit 当您完成了所有的修改操作, 想将原来的设置参数覆盖掉时, 可执行此项功能, 新的设置参数将保存在 CMOS 的存储器中 要执行此操作, 先选定此选项并按下 < Enter > 键, 再按 < Enter > 键即可可退出 Discard Changes and Exit 当您所做的任何更改设置的动作不想存入 CMOS 的存储器中, 可先选定此选项并按下 < Enter > 键, 再按 <Enter > 键即可退出 Discard Changes 当您所做的任何更改设置的动作有误而需要忽略时, 可先选定此选项并按下 < Enter > 键, 然后可以再次进入相应选项进行重新设置 Load Optimal Defaults 此菜单用于在你的系统配置中装入缺省值 这些缺省设置是最优的, 可以发挥所有硬件的高性能 Load Failsafe Defaults 该选项的功能是将各项设置初始化为实现最基本的和最安全的系统功能的值 要执行此项功能, 先选中此选项按下 < Enter > 即可, 接着系统会在屏幕上显示出要您确认的信息, 按下 < Enter > 键确定执行该项功能 CLD2NA 系列

38 第三章 BIOS 功能简介 x86 平台下 BIOS 所要管理的系统资源 这里的系统资源我们定义三种 :I/O 端口地址,IRQ 中断号和 DMA 号 DMA 级别 功能 DMA0 DMA1 DMA2 DRAM 刷新 未分配 软盘 DMA3 未分配 ( 有时用于硬盘 ) DMA4 DMA5 DMA6 DMA7 用于 DMAC 的级联未分配未分配未分配 APIC 高级可编程中断控制器 在现代 P4 以上级别的主板中, 大都支持 APIC, 可以提供多于 16 个中断源, 如 IRQ16 IRQ23, 部分主板如支持 PCI-X 的主板可以有多达 28 个中断源 但要启用该功能必须相应的操作系统支持, 目前只有 windows 2000 以上的操作系统支持 IO 端口地址 系统 I/O 地址空间总共有 64K, 每一外围设备都会占用一段 I/O 地址空间 下表给出了本 CPU 卡部分设备的 I/O 地址分配, 由于 PCI 设备 ( 如 PCI 网卡 ) 的地址是由软件配置的, 表中没有列出 CLD2NA 系列

39 第三章 BIOS 功能简介 地址 设备描述 000h - 00Fh DMA 控制器 #1 000h - CF7h PCI 总线 010h - 01Fh 底板资源 020h - 021h 可编程中断控制器 #1 022h - 03Fh 底板资源 040h - 043h 系统计时器 044h - 05Fh 底板资源 060h 标准 101/102 键或 Microsoft 自然 PS/2 键盘 061h System speaker 062h 063h 底板资源 064h 标准 101/102 键或 Microsoft 自然 PS/2 键盘 065h - 06Fh 底板资源 070h - 071h 实时时钟, NMI 072h 07Fh 底板资源 080h 底板资源 081h - 083h DMA 控制器 #2 084h - 086h 底板资源 087h DMA 控制器 #3 088h 底板资源 089h - 08Bh DMA 控制器 #4 08Ch - 08Eh 底板资源 08Fh DMA 控制器 #5 090h - 09Fh 底板资源 0A0h - 0A1h 可编程中断控制器 #2 0A2h 0BFh 底板资源 CLD2NA 系列

40 第三章 BIOS 功能简介 地址 0C0h - 0DFh DMA 控制器 #6 0E0h - 0EFh 底板资源 0F0h - 0FFh 数据数值处理器 170h - 177h 从 IDE 1F0h - 1F7h 主 IDE 设备描述 274h 277h 279h 2F8h - 2FFh 376h 378h - 37Fh 3B0h 3BBh 3C0h 3DFh 3F0h - 3F5h 3F6h 3F8h - 3FFh 400h - 41Fh 480h - 4BFh 4D0h 4D1h 800h - 87Fh B00h-B0Fh B10h-B1Fh A79h D000h-DFFFh 0D00h-FFFFh ISAPNP Read Data Port ISAPNP Read Data Port 串行端口 #2(COM2) 从 IDE(dual FIFO) 并行端口 #1(LPT1) Intel(R) Q965/Q963 Express Chipset Family Intel(R) Q965/Q963 Express Chipset Family 标准软磁盘控制器 主 IDE(dual FIFO) 串行端口 #1(COM1) Intel(R) 82801G (ICH8 Family) SMBus Controller - 27DA 底板资源 底板资源 底板资源 底板资源 底板资源 ISAPNP Read Data Port Intel(R) ICH8 Family PCI Express Root Port-2849 PCI bus CLD2NA 系列

41 第三章 BIOS 功能简介 IRQ 中断分配表 系统共有 15 个中断源, 有些已被系统设备独占 只有未被独占的中断才可分配给其它设备使用 ISA 设备要求独占使用中断 ; 只有即插即用 ISA 设备才可由 BIOS 或操作系统分配中断 而多个 PCI 设备可共享同一中断, 并由 BIOS 或操作系统分配 下表给出了 X86 平台部分设备的中断分配情况, 但没有给出 PCI 设备所占用的中断资源 级别 功能 IRQ0 IRQ1 IRQ2 系统计时器 标准 101/102 键或 Microsoft 键盘 可编程的中断控制器 IRQ3 串口 #2 IRQ4 串口 #1 IRQ5 并行口 #2 IRQ6 标准软磁盘控制器 IRQ7 并口 #1 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 系统 CMOS/ 实时时钟软件改道到 Int 0Ah 保留保留鼠标端口数字协处理器主 IDE 从 IDE CLD2NA 系列

42 第四章驱动程序安装说明 第四章驱动程序安装说明 本产品的驱动程序可依据配套光盘内容安装, 在此不做介绍 CLD2NA 系列

43 附录 附录 Watchdog 编程指引本主板提供一个可按分或按秒计时的, 最长达 255 级的可编程看门狗定时器 ( 以下简称 WDT) 通过编程,WDT 超时事件可用来将系统复位或者产生一个可屏蔽中断 本主板可使用的中断号为 :3,4,5,7,9,10,11 15 使用前请把 BIOS Setup 界面 PCIPnP 组中对应的 IRQ 号选项值改成 Reserved 以下用 C 语言形式提供了 WDT 的编程范例, 对 WDT 的编程需遵循以下步骤 : 进入 WDT 编程模式 设置 WDT 工作方式 / 启动 WDT/ 关闭 WDT (1) 进入 WDT 编程模式 #define INDEX_PORT #define DATA_PORT 0x4E 0x4F unsigned int tmp_reg; unsigned int pm_base; outportb(index_port, 0x55); outportb(index_port, 0x07); outportb(data_port, 0x0A); outportb(index_port, 0x30); outportb(data_port, 0x01); outportb(index_port, 0x60); tmp_reg = inportb(data_port); pm_base = tmp_reg; CLD2NA 系列

44 附录 outportb(index_port, 0x61); tmp_reg = inportb(data_port); pm_base = pmbase<<8+tmp_reg; /* 此处得到变量 pm_base 供后续程序使用 */ (2) 配置 WDT 工作方式, 复位或中断方式, 选择一种 : a. 配置 WDT 成复位工作方式 outportb(pm_base+0x47, 0x0C); b. 配置 WDT 成中断工作方式 unsigned int irq; irq = IRQ_NO; /* 此处请用需要使用的中断号替换掉常量 IRQ_NO, 赋值给变量 irq, 文档前端已经列出可使用中断号的范围 */ irq = irq<<4; outportb(pm_base+0x47, 0x80); outportb(pm_base+0x67, irq); (3) 配置 WDT 按分或秒计时 : a. 按分计时 : outportb(pm_base+0x65, 0x00); b. 按秒计时 : outportb(pm_base+0x65, 0x80); (4) 启动 / 停止 WDT a. 启动 WDT: CLD2NA 系列

45 附录 outportb(pm_base+0x66, TIME_OUT_VALUE); /* 请以超时时间单位数量 (0x01~0xFF) 替换掉常量 TIME_OUT_VALUE*/ b. 停止 WDT: outportb(pm_base+0x66, 0x00); 数字 IO 编程指引本主板提供 8 路可编程数字 I/O 引脚, 其中 4 路为输入,4 路为输出 以下用 C 语言形式提供了数字 I/0 的编程范例, 对数字 I/O 的编程需遵循以下步骤 : 初始化数字 I/O 输入输出编程 (1) 初始化数字 I/O: #define BAR 0x400 unsigned char tmp_val; outportb(bar,0xbf); outportb(bar+0x04,0x40); outportb(bar+0x03,0x03); outportb(bar+0x05,0x0f); tmp_val =(inportb(bar+0x02) 0x08)&0xeb; tmp_val = 0x40; outportb(bar+0x02, tmp_val); delay(30); tmp_val =inportb(bar); CLD2NA 系列

46 附录 while((tmp_val &0x02)!=0x02) { tmp_val =inportb(bar); if((tmp_val &0x04)!=0) { printf("error\n"); return 0; } } (2) 输入输出编程 : a. 输出编程函数输入 : int pin 取值 1~4 分别对应输出引脚 1~4 int lev_val 1 为输出高电平,0 为输出低电平函数输出 : 无 void Out_Lev(int pin,int lev_val) { unsigned int reg_val ; outportb(bar,0xbf); outportb(bar+0x04,0x40); outportb(bar+0x03,0x01); reg_val = inportb(bar+0x05); reg_val = lev_val? reg_val (0x01<<(pin+3)) :reg_val&(~(0x01<<(pin+3))) ; outportb(bar+0x05, reg_val); CLD2NA 系列

47 附录 reg_val =(inportb(bar+0x02) 0x08)&0xeb; reg_val = 0x40; outportb(bar+0x02, reg_val); delay(30); reg_val =inportb(bar); while((reg_val &0x02)!=0x02) { reg_val =inportb(bar); if((reg_val &0x04)!=0) { printf("error\n"); return 0; } } } b. 输入编程 函数输入 :int pin 取值 1~4 分别对应输入引脚 1~4 函数输出 :int lev_val 1: 输入引脚为高电平,0: 输入引脚为低电平 int In_Lev(int pin) { unsigned int reg_val ; int lev_val ; outportb(bar,0xbf); outportb(bar+0x04,0x41); CLD2NA 系列

48 附录 outportb(bar+0x03,0x00); reg_val =(inportb(bar+0x02) 0x08)&0xeb; reg_val = 0x40; outportb(bar+0x02, reg_val); delay(30); reg_val =inportb(bar); while((reg_val &0x02)!=0x02) { reg_val =inportb(bar); if((reg_val &0x04)!=0) { printf("error\n"); return 0; } } lev_val = inportb(bar+0x05) & (0x01<<(pin-1)); lev_val = lev_val? 1:0; /* 此处得到变量 lev_val 的值, 为 1 表示输入引脚为高电平, 为 0 表示输入引脚为低电平 */ return lev_val ; } 欲获更多信息请访问研祥网站 : CLD2NA 系列

49

50 Announcement What contained in this User Manual does not represent the commitments of EVOC Company. EVOC Company reserves the right to revise this User Manual, without prior notice, and will not be held liable for any direct, indirect, intended or unintended losses and/or hidden dangers due to installation or improper operation. Before purchasing, please have a detailed understanding of the product performance to see whether it meets your requirements. EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. All trademarks, registered trademarks, and trade names used in this User Guide are the property of their respective owners. EVOC Intelligent Technology Co., Ltd. 2009, Copyright Reserved. No part of this manual can be reproduced in any form or by any means, such as in electronic or mechanical way, without permission in writing from EVOC. Safety Instructions 1. Please carefully read the users manual before handling the product; 2. For the board which is not ready to be installed, please put it in the anti-static packaging; 3. Before taking the board out from anti-static packaging, please put your hand on grounded metal object for a while (about 10 seconds) to discharge static; 4. Please wear static protective gloves when holding the board; and always hold the board by edges; 5. Before inserting, removing or re-configuring the motherboard or the expansion card, please firstly disconnect the AC power or unplug the AC power cable from the power source to prevent damage to the product and ensure your personal safety; 6. Before removing the boards or Box PC, firstly turn off all power resources and unplug the power cable from power source; 7. For Box PC products, when inserting or removing boards, please disconnect the AC power in advance; 8. Before connecting or disconnecting any device, make sure all power cables are unplugged in advance; 9. To avoid unnecessary damage caused by turning on/off computer frequently, wait at least 30 seconds before re-turning on the computer.

51 Contents Chapter 1 Product Introduction...1 Overview...1 Mechanical Dimension, Weight and Environment...1 Typical Power Consumption...2 Microprocessor...2 Chipset...2 System Memory...2 Video Function...2 Network Function...2 Audio Function...3 Power Feature...3 Expansion Bus...3 Watchdog Function...3 I/O Connectors...3 Chapter 2 Installation...4 Product Outline...4 Locations of Connectors...5 Motherboard Structure...6 Jumper Settings...7 LCD Backlight Control Connector...8 LED...8 Serial Port...9

52 USB Port...9 Video Connectors...10 LAN Port...12 Multi-functional Connector...12 Audio Connector...13 GPIO Connector...13 JTAG Connector...14 Power Connector...14 CF Card Slot...15 IDE Connector...16 PC/104 Connector...17 PC/104-Plus Connector...18 Chapter 3 BIOS Setup...19 Overview...19 BIOS Parameter Setup...19 Basic Function Settings for BIOS...20 System Resources Managed by BIOS under X86 Platform...34 Chapter 4 Install the Drivers...38 Appendix...39 Watchdog Programming Guide...39 Digital IO Programming Guide...41

53 Chapter 1 Product Introduction Chapter 1 Product Introduction Overview CLD2NA series is an embedded PC/104-Plus motherboard with low power consumption. This motherboard has high integration, small volume, rich functions, low power consumption and it can be widely used in various embedded systems. The main features are listed as follows: Integrate AMD R LX Series CPU with extra low power consumption; On-board 512M DDR2 memory; Two 10/100Mbps Ethernet controllers; Integrate video chip in LX800; support VGA & 18-bit TFT LCD & 18-bit LVDS; support VGA+LVDS, VGA+TFT LCD dual-display function; the max. resolution reaches up to 1280x800; One standard IDE connector; one on-board CF card slot or one on-board 1G NAND FLASH, optional; Four serial ports, two of which support RS232 mode while the other two support RS422/RS485 mode. Four USB 2.0 ports; PC/104 and PC/104-Plus dual-bus expansion. This motherboard is designed with high integration, and it is convenient to be used in various embedded applications via rich connectors, such as medical treatment, instruments, intelligent products, industrial control, national defense and transportation. Mechanical Dimension, Weight and Environment Dimension: 115.6mm (L) x 96.9mm (W) x 23.2mm (H) Net Weight: 109.7g; Operating Environment: Temperature: 0 ~+60 ; Extensible Operating Temperature: -40 ~ CLD2NA Series - 1 -

54 Chapter 1 Product Introduction Humidity: 5% ~ 90%, non-condensing; Storage Environment: Temperature: -40 C ~ 85 C; Humidity: +20% ~ 90%, non-condensing; Typical Power Consumption CPU: AMD R LX800/LX /366MHz Memory: 512MB DDR2 0.98A; +5%/-3%; Microprocessor AMD R LX800 (Standard Configuration)/LX /366MHz BGA481 CPU; Chipset AMD R Geode CS5536; System Memory On-board 512MB DDR2 memory; Video Function Video chip is integrated in LX800; support VGA, TFT LCD and 18-bit LVDS. Support VGA+LVDS dual-display function; do not support VGA+LCD+LVDS synchronous display. The resolution reaches up to 1280x800. Network Function Two 10/100Mbps network ports; do not support Wake-On-LAN CLD2NA Series

55 Chapter 1 Product Introduction Audio Function AC 97 sound effect chip; support MIC-IN, LINE-IN and SPK-OUT; provide excellent sound effect. Power Feature AT power, +5V single power supply; Expansion Bus One PC/104 slot, ISA bus compliant; one PC/104-Plus slot, PCI bus compliant; Watchdog Function 255 levels, programmable, time by minute or second; Support watchdog overtime or reset system. I/O Connectors Four serial ports, two of which support RS-232 mode while the other two support RS-422/RS-485 mode selection; One IDE connector, it supports two IDE devices; one CF card slot or on-board 1G NAND FLASH (Slave as default), optional; Two sets of USB2.0 connectors, which can transfer four USB ports; One multi-functional connector, it supports a set of PS2 keyboard and mouse, one buzzer and one reset button; One VGA connector; one LVDS connector; one TFT LCD connector; One audio connector; One 8-bit digital I/O connector; CLD2NA Series - 3 -

56 Chapter 2 Installation Chapter 2 Installation Product Outline R unit:mm CLD2NA Series

57 Chapter 2 Installation Locations of Connectors JTAG1 JLCD1 LCDB1 JP1 JCC1 JP3 J3 JP2 AUDIO1 GPIO1 USB2 USB1 LAN2 LAN1 D8 J1 LCD1 COM3 COM4 J4 VGA1 LVDS1 COM1 COM2 D7 D5 J2 IDE1 JCF1 PWR1 Front View CLD2NA Series - 5 -

58 Chapter 2 Installation CF1 Rear View Motherboard Structure VGA LVDS LCD CRT TFT CPU AMD Geode LX Processor MEMORY BUS FPGA MEMORY BUS DDRII CF Card or 1G flash TFT LCD PCI BUS (33MHz) PC104+ PCI to ISA PC/104 IDE PRIMARY IDE 10 / 100 ETHERNET PORT USB2.0X4 GPIO USB2.0 SMBUS Companion Device AMD Geode CS5536 AC97 AUDIO CODEC 10 / 100 ETHERNET PORT LPC BIOS SIO LEGACY SERIAL*4 KB/MS CLD2NA Series

59 Chapter 2 Installation Tip: How to identify the first pin of the jumpers and connectors 1. Observe the letter beside the socket, it would be marked with 1 or thickened lines or triangular symbols; 2. Observe the solder pad on the back, the square pad is the first pin; 3. The red line on the cable or other marks show that they should be connected with the first pin of the socket Jumper Settings 1. JCC1: Clear/Keep CMOS Setting (Pin Distance: 2.0mm) CMOS is powered by the button battery on board. Clearing CMOS will restore original settings (factory default). The steps are listed as follows : (1) Turn off the computer and unplug the power cable; (2) Instantly short circuit JCC1; (3) Turn on the computer; (4) Follow the prompt on screen to enter BIOS setup when starting the computer, load optimized defaults; (5) Save and exit. Please set it as follows: JCC1 Setup Function 1-2 Open Normal (Default) 1-2 Short Clear the contents of CMOS, all BIOS setting will restore to factory default values. 2. JLCD1: Select Operating Voltage for LCD (Pin Distance: 2.0mm) Different LCD screens have different voltages; the board provides two voltage options, 3.3V and 5V. Only when the selected LCD voltage is in accord with the LCD voltage in use, can the LCD screen display normally. Please set it as follows: Setup Function 1-2 Short +3.3V (Default) JLCD1 2-3 Short +5V 3. JP3: Select Master/Slave Mode for CF Card (Pin Distance: 2.0 mm) Setup Function 1-2 Short Master JP3 1-2 Open Slave (Default) CLD2NA Series - 7 -

60 Chapter 2 Installation 4. JCF1: Select Operating Voltage for CF Card (Pin Distance: 2.0mm) Setup Function JCF1 1-2 Short +3.3V 2-3 Short +5V (Default) 5. JP1, JP2: Select Serial Port Mode (Pin Distance: 2.0 mm) COM3 and COM4 support optional RS-422/RS-485, JP1 and JP2 can be used to carry out the selection. Please set it as follows: Pin Setup Mode Selection RS-485 (Default) RS-422 JP JP1/JP2 JP Note: 1-2 indicates the status of the jumper cap. LCD Backlight Control Connector Pin Signal Name 1 VCC_LCDBKLT 2 NC LCDB1 3 LCD_BKLTEN (Pin Distance: 2.0 mm) 4 GND Note: VCC_LCDBKLT----backlight power, the current is limited below 1A.) LCD_BKLTEN ---- backlight enabling, active high LED LED Function D5/D7/D8 D5 (Green) D7 (Red) D8 (Red) IDE Indicator Power Indicator FPGA Operating Indicator CLD2NA Series

61 Chapter 2 Installation Serial Port This board provides four 2 5Pin headers for serial ports (Pin Distance: 2.0mm). COM1 and COM2 support RS-232 mode, COM3 and COM4 can select RS-422 or RS-485 mode via setting JP1 and JP2, the default is RS-485. COM3 and COM4 support automatic data transmission at RS-485 mode. The pin definitions are listed as follows: Signal Name Pin COM1/COM2 COM3/COM4 RS-232 RS-422 RS-485 (Default) 1 DCD# TXD- Data- 2 RXD TXD+ Data+ 3 TXD RXD+ NC 4 DTR# RXD- NC COM1 ~ COM4 5 GND GND GND 6 DSR# NC NC 7 RTS# NC NC 8 CTS# NC NC 9 RI# NC NC 10 NA NA NA USB Port This motherboard provides two 2x5 Pin (Pin 9 is NC) USB connectors. Four USB ports can be educed via transfer cable. The pin definitions are listed as follows: Pin Signal Name Pin Signal Name 1 +5V 2 +5V 3 USB1_Data- 4 USB2_Data- USB1/USB2 (Pin Distance: 2.0 mm) 5 USB1_Data+ 6 USB2_Data+ 7 GND 8 GND 9 NA 10 GND_CHASSIS CLD2NA Series - 9 -

62 Chapter 2 Installation Video Connectors 1. VGA Connector Pin Signal Name Pin Signal Name 1 VSYNC 2 HSYNC 3 DDCDATA 4 Red VGA1 (Pin Distance: 2.0 mm) 5 DDCCLK 6 Green 7 +5V 8 Blue 9 GND 10 GND Note: when using VGA in WinXP system, if the resolution is , please set the same value in BIOS Setup. Please set it as follows: Press DEL to enter SETUP menu--enter Chipset option---enter North Bridge Configure Menu--- Video Configuration Menu---Flat Panel Resolution Menu, change the resolution from (Default) to bit LVDS Connector Pin Signal Name Pin Signal Name 1 LVDS_D0+ 2 LVDS_D0-3 GND 4 GND 5 LVDS_D1+ 6 LVDS_D1-7 GND 8 GND 9 LVDS_D2+ 10 LVDS_D2-11 GND 12 GND 13 CLK+ 14 CLK- LVDS1 15 GND 16 GND (Pin Distance: NC 18 NC mm) 19 VDD 20 VDD CLD2NA Series

63 Chapter 2 Installation 3. TFT LCD Connector Pin Signal Name Pin Signal Name 1 +12V 2 +12V 3 GND 4 GND 5 VCC_LCD 6 VCC_LCD 7 ENAVEE 8 GND 9 B0 10 B1 11 B2 12 B3 13 B4 14 B5 15 B6 16 B7 17 G0 18 G1 19 G2 20 G3 21 G4 22 G5 23 G6 24 G7 25 R0 26 R1 27 R2 28 R3 29 R4 30 R5 31 R6 32 R7 LCD1 33 GND 34 GND 35 CLK 36 VSYNC 37 DE 38 HSYNC 39 GND 40 ENABKL 41 GND 42 NC 43 ENAVDD 44 VCON Note: ENAVEE: LCD Bias Voltage Enabling; ENABKL: LCD Backlight Enabling; ENAVDD: LCD Power Enabling; VCON: Luminance Adjustment; CLD2NA Series

64 Chapter 2 Installation LAN Port LAN1 and LAN2 are 2 5Pin headers for Ethernet port on the motherboard, transfer cable is required to connect the signals to the standard sockets. The pin definitions are listed as follows: Pin Signal Name Pin Signal Name 1 LED+ 2 LINK_ LED- 3 RX+ 4 RX- 5 ACT_LED- 6 TERMINAL1 7 TERMINAL2 8 GND LAN1/LAN2(Pin Distance: 2.0 mm) 9 TX+ 10 TX- ACTLED (Green) LAN Activity Status Indicator LILED (Yellow) LAN Speed Indicator Blink Data transmitting ON 100Mbps OFF No Data to Transmit OFF 10Mbps Multi-functional Connector J4 is a 2 5 Pin header, this is a multi-functional connector and it is used to connect keyboard, mouse, buzzer and Reset button. The multi-functional cable attached to the single board computer is required. The pin definitions are listed as follows: Pin Signal Name Pin Signal Name 1 SPEAK- 2 +5V 3 Reset 4 GND J4 5 Keyboard Data 6 Keyboard Clock 7 GND 8 Mouse Clock (Pin Distance: 2.0 mm) 9 +5V 10 Mouse Data CLD2NA Series

65 Chapter 2 Installation Audio Connector LOUT can connect to earphone or more compatible power loudspeaker via the cable attached to the motherboard. MIC_IN is used to connect the microphone and input the sound. The pin definitions are listed as follows: Pin Signal Name Pin Signal Name 1 LOUT_R 2 LOUT_L 3 GND_AUDIO 4 GND_AUDIO 5 LIN_R 6 LIN_L AUDIO1 7 GND_AUDIO 8 GND_AUDIO (Pin Distance: 2.0 mm) 9 MIC_IN 10 MIC_P GPIO Connector This motherboard provides one 8-channel programmable GPIO port; the input and output can be controlled discretionarily by programming. The default status is that pin 1, 3, 5 and 7 are for output and pin 2, 4, 6 and 8 are for output. The pin definitions are listed as follows: Pin Signal Name Pin Signal Name 1 GPIO1 2 GPIO5 3 GPIO2 4 GPIO6 GPIO1 (Pin Distance: 2.0 mm) 5 GPIO3 6 GPIO7 7 GPIO4 8 GPIO8 9 GND 10 NC CLD2NA Series

66 Chapter 2 Installation JTAG Connector JTAG1 is used to record on-board XILINX FPGA code (Reserved). Pin Signal Name 1 VCC 2 GND JTAG1 (Pin Distance: 2.0 mm) 3 TCK 4 TDO 5 TDI 6 TMS Power Connector Pin Signal Name Pin Signal Name 1 GND 2 +5V 3 NC 4 +12V PWR1 (Pin Distance: 2.54 mm) 5 NC 6-12V 7 GND 8 +5V 9 GND 10 +5V CLD2NA Series

67 Chapter 2 Installation CF Card Slot Compact Flash card is a sort of high speed memory, small in size and easy to use. Its storage capacity will vary with different cards in use, such as 128M, 256M etc. This board provides one CF card (on the rear of the board, marked as CF1) and it could only be inserted in one direction. Pin Signal Name Pin Signal Name 1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS0# 32 CS1# 8 GND 33 VS1# 9 ATASEL# 34 IOR# 10 GND 35 IOW# 11 GND 36 WE# 12 GND 37 IRQ 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 VS2# 16 GND 41 RESET# 17 GND 42 IORDY 18 A2 43 DREQ 19 A1 44 DACK# 20 A0 45 DASP# 21 D0 46 ATA66_DET 22 D1 47 D8 23 D2 48 D9 24 WP/IOCS16# 49 D10 25 CD2# 50 GND CLD2NA Series

68 Chapter 2 Installation IDE Connector This board provides a set of 2 5Pin header (Pin Distance: 2.0 mm). Please pay attention as follows when installing IDE device: One set of IDE connector could be connected with two IDE devices: one is Master and the other is Slave. The connecting method is: connect the master device to the end of the cable while connect the slave device to the middle of the cable. (The first pin of the IDE cable is red.) Pin Signal Name Pin Signal Name 1 RESET# 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 Key 21 DREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 IORDY 28 GND 29 DACK# 30 GND 31 IRQ 32 NC IDE1 33 DA1 34 ATA66_DET 35 DA0 36 DA2 37 CS1# 38 CS3# 39 LED# 40 GND 41 +5V 42 +5V 43 GND 44 GND CLD2NA Series

69 Chapter 2 Installation PC/104 Connector Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name A1 IOCHCK# B1 GND C1 GND D1 GND A2 SD7 B2 RESET C2 SBHE# D2 MEMCS16# A3 SD6 B3 +5V C3 LA23 D3 IOCS16# A4 SD5 B4 IRQ9 C4 LA22 D4 IRQ10 A5 SD4 B5-5V C5 LA21 D5 IRQ11 A6 SD3 B6 DRQ2 C6 LA20 D6 IRQ12 A7 SD2 B7-12V C7 LA19 D7 IRQ15 A8 SD1 B8 SRDY# C8 LA18 D8 IRQ14 A9 SD0 B9 +12V C9 LA17 D9 DACK0# A10 IOCHRDY B10 KEY C10 MEMR# D10 DRQ0 A11 AEN B11 SMEMW# C11 MEMW# D11 DACK5# A12 SA19 B12 SMEMR# C12 SD8 D12 DRQ5 A13 SA18 B13 IOW# C13 SD9 D13 DACK6# A14 SA17 B14 IOR# C14 SD10 D14 DRQ6 A15 SA16 B15 DACK3# C15 SD11 D15 DACK7# A16 SA15 B16 DRQ3 C16 SD12 D16 DRQ7 A17 SA14 B17 DACK1# C17 SD13 D17 +5V A18 SA13 B18 DRQ1 C18 SD14 D18 MASTER# A19 SA12 B19 REFRESH# C19 SD15 D19 GND A20 SA11 B20 BCLK C20 KEY D20 GND A21 SA10 B21 IRQ7 A22 SA9 B22 IRQ6 A23 SA8 B23 IRQ5 A24 SA7 B24 IRQ4 A25 SA6 B25 IRQ3 A26 SA5 B26 DACK2# A27 SA4 B27 TC A28 SA3 B28 BALE A29 SA2 B29 +5V A30 SA1 B30 OSC A31 SA0 B31 GND A32 GND B32 GND CLD2NA Series

70 Chapter 2 Installation PC/104-Plus Connector Support PCI The pin definitions are listed as follows: J3 Pin Signal Name Pin Signal Name Pin Signal Name Pin Signal Name A1 KEY B1 NC C1 +5V D1 AD0 A2 NC B2 AD2 C2 AD1 D2 +5V A3 AD5 B3 GND C3 AD4 D3 AD3 A4 C/BE0# B4 AD7 C4 GND D4 AD6 A5 GND B5 AD9 C5 AD8 D5 GND A6 AD11 B6 NC C6 AD10 D6 NC A7 AD14 B7 AD13 C7 GND D7 AD12 A8 +3.3V B8 C/BE1# C8 AD15 D8 +3.3V A9 SERR# B9 GND C9 NC D9 PAR A10 GND B10 PERR# C V D10 NC A11 STOP# B V C11 PLOCK# D11 GND A V B12 TRDY# C12 GND D12 DEVSEL# A13 FRAME# B13 GND C13 IRDY# D V A14 GND B14 AD16 C V D14 C/BE2# A15 AD18 B V C15 AD17 D15 GND A16 AD21 B16 AD20 C16 GND D16 AD19 A V B17 AD23 C17 AD22 D V A18 IDSEL0 B18 GND C18 IDSEL1 D18 IDSEL2 A19 AD24 B19 C/BE3# C19 NC D19 IDSEL3 A20 GND B20 AD26 C20 AD25 D20 GND A21 AD29 B21 +5V C21 AD28 D21 AD27 A22 +5V B22 AD30 C22 GND D22 AD31 A23 REQ0# B23 GND C23 REQ1# D23 NC A24 GND B24 REQ2# C24 +5V D24 GNT0# A25 GNT1# B25 NC C25 GNT2# D25 GND A26 +5V B26 CLK0 C26 GND D26 CLK1 A27 CLK2 B27 +5V C27 CLK3 D27 GND A28 GND B28 PIRQD# C28 +5V D28 RESET# A29 +12V B29 PIRQA# C29 PIRQB# D29 PIRQC# A30-12V B30 REQ3# C30 GNT3# D30 GND CLD2NA Series

71 Chapter 3 BIOS Setup Chapter 3 BIOS Setup Overview BIOS (Basic Input and Output System) is solidified in the flash memory on the CPU board. Its main functions include: initialize system hardware, set the operating status of the system components, adjust the operating parameters of the system components, diagnose the functions of the system components and report failures, provide hardware operating and controlling interface for the upper level software system, guide operating system and so on. BIOS provides users with a human-computer interface in menu style to facilitate the configuration of system parameters for users, control power management mode and adjust the resource distribution of system device, etc. Setting the parameters of the BIOS correctly could enable the system operating stably and reliably; it could also improve the overall performance of the system at the same time. Inadequate even incorrect BIOS parameter setting will decrease the system operating capability and make the system operating unstably even unable to operate normally. BIOS Parameter Setup Prompt message for BIOS setting may appear once powering on the system. At that time (inefficient at other time), press the key specified in the prompt message (usually <Del>) to enter BIOS setting. When the BIOS setting in CMOS is destroyed, system may also require entering BIOS setting or selecting certain default value. All the setup values modified by BIOS are saved in the CMOS storage in system. The CMOS storage is powered by battery; unless clearing CMOS contents, or else its contents will not be lost even if powered off. Note! BIOS setting will influent the computer performance directly. Setting parameter improperly will cause damage to the computer; it may even unable to power on. Please use the internal default value of BIOS to restore the system. Our company is constantly researching and updating BIOS, its setup interface may be a bit different. The figure below is for reference only; it may be different from your BIOS setting in use CLD2NA Series

72 Chapter 3 BIOS Setup Basic Function Settings for BIOS After starting SETUP program, the main interface of CMOS Setup Utility will appear: BIOS SETUP UTILITY System Overview Processor Type :AMD Geode LX Speed : 500MHz System Memory Size :231MB Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit System Time [00:47:55] System Date [Wed 01/02/2009] V02.57 (c)copyright ,American Megatrends, Inc. Main System Time Select this option and set the current time by < + > / < - >, which is displayed in format of hour/minute/second. Reasonable range for each option is: Hour (00-23), Minute (00-59), Second (00-59). System Date Select this option and set current data by < + > / < - >, which is displayed in format of month/date/year. Reasonable range for each option is: Month (Jan.-Dec.), Date (01-31), Year (Maximum to 2099), Week (Mon. ~ Sun.) CLD2NA Series

73 Chapter 3 BIOS Setup Advanced Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction BIOS SETUP UTILITY Configure CPU CPU Configuration IDE Configuration Super IO Configuration ISA I/O Decode Configuration ISA Memory Decode Configuration ISA DDMA Channels Configuration Hardware Health Configuration USB Configuration Power Management Configuration Select Screen Select Item Enter Go to Sub Screen Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. CPU Configuration BIOS SETUP UTILITY CPU Configuration Manufacturer: AMD Brand String: AMD Geode LX Frequency :500MHz Cache L1 :64 KB Cache L2 :128 KB Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc CLD2NA Series

74 Chapter 3 BIOS Setup IDE Configuration BIOS SETUP UTILITY IDE Configuration Onboard PCI IDE Controller [Primary] Primary IDE Master :[Not Detected] Primary IDE Slave :[Not Detected] Select Screen Select Item + - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.57 (c)copyright , American Megatrends, Inc. Primary IDE Master/Slave * Type Not Installed: IDE device cannot be detected by system; AUTO: automatic detection of IDE parameters when power on; CD/DVD: used for ATAPI CDROM; ARMD: used for various analog IDE devices. * LBA/Large Mode Used to set whether to support LBA mode or not. * Block(Multi-sector Transfer) Used to set whether to support multi-sector simultaneous transfer or not. * PIO Mode Used for PIO mode setting. * DMA Mode Used for DMA mode setting. * S.M.A.R.T Used to set whether to enable S.M.A.R.T function and it is only effective for the hard disk supporting this function. * 32Bit Data Transfer This option is used to enable 32-bit hard disk accessing mode, which could optimize hard disk read and write speed CLD2NA Series

P4V88+_BIOS_CN.p65

P4V88+_BIOS_CN.p65 1 Main H/W Monitor Boot Security Exit System Overview System Time System Date [ 17:00:09] [Wed 12/22/2004] BIOS Version : P4V88+ BIOS P1.00 Processor Type : Intel (R) Pentium (R) 4 CPU 2.40 GHz Processor

More information

P4i45GL_GV-R50-CN.p65

P4i45GL_GV-R50-CN.p65 1 Main Advanced Security Power Boot Exit System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 Dec 18 2003 Thu

More information

P4Dual-915GL_BIOS_CN.p65

P4Dual-915GL_BIOS_CN.p65 1 Main H/W Monitor Boot Security Exit System Overview System Time System Date Total Memory DIMM 1 DIMM 2 [ 14:00:09] [Wed 01/05/2005] BIOS Version : P4Dual-915GL BIOS P1.00 Processor Type : Intel (R) Pentium

More information

P4VM800_BIOS_CN.p65

P4VM800_BIOS_CN.p65 1 Main H/W Monitor Boot Security Exit System Overview System Time System Date [ 17:00:09] [Fri 02/25/2005] BIOS Version : P4VM800 BIOS P1.00 Processor Type : Intel (R) Pentium (R) 4 CPU 2.40 GHz Processor

More information

775i65PE_BIOS_CN.p65

775i65PE_BIOS_CN.p65 1 Main H/W Monitor Boot Security Exit System Overview System Time System Date [ 14:00:09] [Wed 10/20/2004] BIOS Version : 775i65PE BIOS P1.00 Processor Type : Intel (R) CPU 3.20 GHz Processor Speed : 3200

More information

中文手册

中文手册 PCC-3428 PC/104 1. PCC-3428 1.1 PCC-3428 90mm 96mm ST CPU STPC Atlas Atlas CPU 486 DX/DX2 CPU DX2 133MHz Atlas 2D LCD/CRT 100MHz SDRAM 64MBytes PCC-3428 10/100Mbps DOC EIDE USB PC/104 ST STPC Atlas STPC

More information

Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10

Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Serial ATA ( Silicon Image SiI3114)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Ác Åé å Serial ATA ( Silicon Image SiI3114) S A T A (1) SATA (2)

More information

PCM-3386用户手册.doc

PCM-3386用户手册.doc PCM-3386 BBPC-4x86 10/100M PC/104 (Lanry technology Co. Ltd. Zhuhai) 38 1012836 (Address: Room 1012,Linhai Building,No. 38,west of Shihua Road,Zhuhai City,Guangdong Province,China) (post code)519015 (phone)0756-3366659

More information

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact

More information

第4章 系统设置

第4章  系统设置 POST 4.1 POST BIOS POST POST POST POST LOGO LOGO POST BIOS POST POST SCSI SCSI BIOS RAID POST RAID RAID RAID BIOS Operating System not Found BIOS T200 2002 BIOS 4.2 BIOS BIOS

More information

K7M SLOT 1

K7M SLOT 1 K7M SLOT 1 1999 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 2 3 4 5 6 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 13 USB PS/2 COM1 COM2 CPU Core Voltage Setting

More information

Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c) Windows XP

Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c) Windows XP Serial ATA ( Sil3132)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 10 (5) S A T A... 12 Ác Åé å Serial ATA ( Sil3132) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS

More information

IT (1) IDE... 2 (2) BIOS IDE RAID... 3 (3) RAID BIOS RAID... 5 (4) R A I D (5) ID E RA ID... 15

IT (1) IDE... 2 (2) BIOS IDE RAID... 3 (3) RAID BIOS RAID... 5 (4) R A I D (5) ID E RA ID... 15 IT8212...2 (1) IDE... 2 (2) BIOS IDE RAID... 3 (3) RAID BIOS RAID... 5 (4) R A I D... 13 (5) ID E RA ID... 15 Ác Åé å IT8212 (1) IDE (2) BIOS IDE RAID (3) RAID BIOS RAID (4) RAID (5) RAID (a) ( )IDE (

More information

Serial ATA ( Nvidia nforce430)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A (6) Microsoft Win

Serial ATA ( Nvidia nforce430)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A (6) Microsoft Win Serial ATA ( Nvidia nforce430)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A... 11 (6) Microsoft Windows 2000... 14 Ác Åé å Serial ATA ( Nvidia nforce430)

More information

P3B-F Pentium III/II/Celeron TM

P3B-F Pentium III/II/Celeron TM P3B-F Pentium III/II/Celeron TM 1999 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 13 R PS2 KBMS USB COM1 COM2 JTPWR ATXPWR PWR_FAN CPU_FAN Row 0 1 2 3 4 5 6 7 DSW JP20

More information

如 果 此 設 備 對 無 線 電 或 電 視 接 收 造 成 有 害 干 擾 ( 此 干 擾 可 由 開 關 設 備 來 做 確 認 ), 用 戶 可 嘗 試 用 以 下 一 種 或 多 種 方 法 來 消 除 這 個 干 擾 : 重 新 調 整 與 確 定 接 收 天 線 方 向 增 大 此 設

如 果 此 設 備 對 無 線 電 或 電 視 接 收 造 成 有 害 干 擾 ( 此 干 擾 可 由 開 關 設 備 來 做 確 認 ), 用 戶 可 嘗 試 用 以 下 一 種 或 多 種 方 法 來 消 除 這 個 干 擾 : 重 新 調 整 與 確 定 接 收 天 線 方 向 增 大 此 設 版 權 前 言 本 出 版 物, 包 括 所 有 照 片 插 圖 與 軟 體 均 受 國 際 版 權 法 之 保 護, 所 有 權 利 均 被 保 留 此 說 明 書 和 其 中 所 包 含 的 任 何 材 料 都 不 可 以 在 沒 有 作 者 的 書 面 許 可 下 被 複 製 版 本 1.0 免 責 聲 明 製 造 商 不 對 說 明 書 內 容 作 任 何 陳 述 或 擔 保, 基 於 此

More information

P3V4X JumperFree TM

P3V4X JumperFree TM P3V4X JumperFree TM 1999 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 13 19.3cm (7.6in) COM1 COM2 PS2KBMS JTPWR

More information

P3C2000 JumperFree TM Camino

P3C2000 JumperFree TM Camino P3C2000 JumperFree TM Camino 1999 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 13 USB

More information

典型自编教材

典型自编教材 河 南 科 技 大 学 计 算 机 实 验 教 学 中 心 1. 计 算 机 文 化 基 础 实 验 指 导 书 2. 数 据 结 构 实 验 指 导 书 3. 操 作 系 统 实 验 指 导 书 4. 面 向 对 象 程 序 设 计 实 验 指 导 书 5. 数 据 库 原 理 实 验 指 导 书 6. 编 译 原 理 实 验 指 导 书 7. JAVA 程 序 设 计 实 验 指 导 书 8.

More information

Serial ATA ( nvidia nforce4 Ultra/SLI)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A (6) Micro

Serial ATA ( nvidia nforce4 Ultra/SLI)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A (6) Micro Serial ATA ( nvidia nforce4 Ultra/SLI)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A... 11 (6) Microsoft Windows 2000... 14 Ác Åé å Serial ATA ( nvidia

More information

NORCO-740 CPU M/00M NORCO-740 NORCO-740E NORCO-740G NORCO-740GE Intel 845GL Intel 845G

NORCO-740 CPU M/00M NORCO-740 NORCO-740E NORCO-740G NORCO-740GE Intel 845GL Intel 845G 3. 4.2 4 2. 2.. 8 2..2 VGA 8 2..3 (J2,J3,J5) 9 2..4 9 2..5 USB 20 2..6 MS KB 20 2..7 (J) 20 2..8 2 2..9 2 2..0 22 2.. (IDE,2) 22 2..2 22 2..3 AC 97 23 2.2 2.2. FSB :JFS 24 2.2.2 Watchdog Timer :JWD 24

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

RAID RAID 0 RAID 1 RAID 5 RAID * ( -1)* ( /2)* No Yes Yes Yes A. B. BIOS SATA C. RAID BIOS RAID ( ) D. SATA RAID/AHCI ( ) SATA M.2 SSD ( )

RAID RAID 0 RAID 1 RAID 5 RAID * ( -1)* ( /2)* No Yes Yes Yes A. B. BIOS SATA C. RAID BIOS RAID ( ) D. SATA RAID/AHCI ( ) SATA M.2 SSD ( ) RAID RAID 0 RAID 1 RAID 5 RAID 10 2 2 3 4 * (-1)* (/2)* No Yes Yes Yes A. B. BIOS SATA C. RAID BIOS RAID ( ) D. SATA RAID/AHCI ( ) SATA M.2 SSD ( ) ( ) ( ) Windows USB 1 SATA A. SATASATAIntel SATA (SATA3

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

Ác Åé å Serial ATA ( nvidia nforce4 SLI) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c)

Ác Åé å Serial ATA ( nvidia nforce4 SLI) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5) SATA (a) S A T A ( S A T A R A I D ) (b) (c) Serial ATA ( nvidia nforce4 SLI)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 6 (4) S A T A... 9 (5) S A T A... 11 (6) Microsoft Windows 2000... 14 Ác Åé å Serial ATA ( nvidia nforce4

More information

CANVIO_AEROCAST_CS_EN.indd

CANVIO_AEROCAST_CS_EN.indd 简 体 中 文...2 English...4 SC5151-A0 简 体 中 文 步 骤 2: 了 解 您 的 CANVIO AeroCast CANVIO AeroCast 无 线 移 动 硬 盘 快 速 入 门 指 南 欢 迎 并 感 谢 您 选 择 TOSHIBA 产 品 有 关 您 的 TOSHIBA 产 品 的 详 情, 请 参 阅 包 含 更 多 信 息 的 用 户 手 册 () 安

More information

TX-NR3030_BAS_Cs_ indd

TX-NR3030_BAS_Cs_ indd TX-NR3030 http://www.onkyo.com/manual/txnr3030/adv/cs.html Cs 1 2 3 Speaker Cable 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT 1 DIGITAL OPTICAL OUT AUDIO OUT TV 3 1 5 4 6 1 2 3 3 2 2 4 3 2 5

More information

Logitech Wireless Combo MK45 English

Logitech Wireless Combo MK45 English Logitech Wireless Combo MK45 Setup Guide Logitech Wireless Combo MK45 English................................................................................... 7..........................................

More information

GA-8IG P4 533 Pentium Rev MC-8IG-1201

GA-8IG P4 533 Pentium Rev MC-8IG-1201 GA-8IG P4 533 Pentium Rev. 20 2MC-8IG-20 ... 3... 3... 4... 4 GA-8IG Layout... 6... 7 (CPU... 8 -... 8-2... 9 2... 0 3... 2 4:... 3 4- I/O... 3 4-2... 5 4-3... 2 GA-8IG - 2 - GA-8IG GA-8IG x / x x. 2.

More information

2 : ; :

2 : ; : 4 CH 1 2 : ; : 1 2 2 3 3 4 4 5 5 6 1 6 2 8 3 11 6 13 1 13 2 14 14 1 15 2 16 3 17 4 18 5 22 6 23 7 24 7 CF 32 8 46 9 : 80GB HD 48 3 3 1 : 4 / / 4 9 2 CHANNEL 1 : 1 3 CHANNEL 2 : 2 4 CHANNEL 3 : 3 5 CHANNEL

More information

T

T T10452 2015 5 Copyright ASUSTeK Computer Inc. All rights reserved. http://support.asus.com 0800-093-456 1 2 2 筆記型電腦使用手冊 使用手冊... 7 手冊... 8... 8... 8... 9 使用... 9...10...10 筆記型電腦...12...12...16...18...20...22

More information

PTS7_Manual.PDF

PTS7_Manual.PDF User Manual Soliton Technologies CO., LTD www.soliton.com.tw - PCI V2.2. - PCI 32-bit / 33MHz * 2 - Zero Skew CLK Signal Generator. - (each Slot). -. - PCI. - Hot-Swap - DOS, Windows 98/2000/XP, Linux

More information

T1028_Manual_KO_V3 0.pdf

T1028_Manual_KO_V3 0.pdf 2009 : 2009/09 PC Microsoft, MS-DOS, Windows, Windows Sound System Microsoft Corporation Intel, Atom Intel Corporation Sound Blaster, Sound Blaster ProCreative Technology I AC AC AC AC AC - 115 V/60 Hz

More information

CONTENTS Chapter - Introduction Chapter 2 - Hardware Installation Chapter 3 - BIOS Setup Utility Chapter 4 - Supported Software M804

CONTENTS Chapter - Introduction Chapter 2 - Hardware Installation Chapter 3 - BIOS Setup Utility Chapter 4 - Supported Software M804 MBS-S65B-ML Pentium 4 478-pin processor Based DDR MAIN BOARD CONTENTS Chapter - Introduction Chapter 2 - Hardware Installation Chapter 3 - BIOS Setup Utility Chapter 4 - Supported Software M804 Chapter

More information

AL-MX200 Series

AL-MX200 Series PostScript Level3 Compatible NPD4760-00 TC Seiko Epson Corporation Seiko Epson Corporation ( ) Seiko Epson Corporation Seiko Epson Corporation Epson Seiko Epson Corporation Apple Bonjour ColorSync Macintosh

More information

solutions guide

solutions guide solutions guide Tridium 01 Table of Contents Tridium... 1 Frameworks... 4 Niagara AX Framework... 5 Sedona Framework... 6.... 7 NPM... 8 Sedona Chip... 9 AX Supervisor... 10 AX SoftJACE...11...12. JACE

More information

V6800/V6600 3D

V6800/V6600 3D V6800/V6600 3D V6600/V6800 3D R 2000 2 3 4 5 R 6 7 8 The VIP (Video Interface Port) Connector are used for third party add-on modules, such as video capture cards or television tuners. DDR: Double Data

More information

+01-10_M5A_C1955.p65

+01-10_M5A_C1955.p65 Notebook PC User s Manual C1955 1.01 2005 4 2 50 70 3 (0 30 ) (50 122 ) 4 pre-load Fn+F7 5 ...2...3...6 1-1...12...12...13...14...15...16...17 1-2...18 1-3...20...20...21...21...21...21...22...22...22...22...23...23

More information

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO Car DVD New GUI IR Flow User Manual V0.1 Jan 25, 2008 19, Innovation First Road Science Park Hsin-Chu Taiwan 300 R.O.C. Tel: 886-3-578-6005 Fax: 886-3-578-4418 Web: www.sunplus.com Important Notice SUNPLUS

More information

ICD ICD ICD ICD ICD

ICD ICD ICD ICD ICD MPLAB ICD2 MPLAB ICD2 PIC MPLAB-IDE V6.0 ICD2 usb PC RS232 MPLAB IDE PC PC 2.0 5.5V LED EEDATA MPLAB ICD2 Microchip MPLAB-IDE v6.0 Windows 95/98 Windows NT Windows 2000 www.elc-mcu.com 1 ICD2...4 1.1 ICD2...4

More information

BC04 Module_antenna__ doc

BC04 Module_antenna__ doc http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 1 of 10 http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 2 of 10 http://www.infobluetooth.com TEL:+86-23-68798999

More information

Guide to Install SATA Hard Disks

Guide to Install SATA Hard Disks SATA RAID 1. SATA. 2 1.1 SATA. 2 1.2 SATA 2 2. RAID (RAID 0 / RAID 1 / JBOD).. 4 2.1 RAID. 4 2.2 RAID 5 2.3 RAID 0 6 2.4 RAID 1.. 10 2.5 JBOD.. 16 3. Windows 2000 / Windows XP 20 1. SATA 1.1 SATA Serial

More information

Serial ATA ( Silicon Image SiI3512)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10

Serial ATA ( Silicon Image SiI3512)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Serial ATA ( Silicon Image SiI3512)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 Ác Åé å Serial ATA ( Silicon Image SiI3512) S A T A (1) SATA (2)

More information

TPM BIOS Infineon TPM Smart TPM Infineon TPM Smart TPM TPM Smart TPM TPM Advanced Mode...8

TPM BIOS Infineon TPM Smart TPM Infineon TPM Smart TPM TPM Smart TPM TPM Advanced Mode...8 Smart TPM Rev. 1001 Smart TPM Ultra TPM Smart TPM TPM...3 1. BIOS... 3 2. Infineon TPM Smart TPM... 4 2.1. Infineon TPM...4 2.2. Smart TPM...4 3. TPM... 5 3.1. Smart TPM TPM...5 3.2. Advanced Mode...8

More information

T

T T10362 2015 5 Copyright ASUSTeK Computer Inc. All rights reserved. http://support.asus.com 0800-093-456 1 2 2 筆記型電腦使用手冊 使用手冊... 7 手冊... 8... 8... 8... 9 使用... 9...10...10 Energy Star...11 筆記型電腦...14...14...18...20...22...24

More information

LH_Series_Rev2014.pdf

LH_Series_Rev2014.pdf REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check

More information

员工签到录

员工签到录 Archivist 2002 Eletech Enterprise Co., Ltd. All Rights Reserved. 1-1 ELETECH VOICE SYSTEMS INC 2 / 2 VLR, 1-1-1 VP894AS-M11 1. VP894AS-M11 1 2. Y 4 3. RJII 4 4. 2-PIN 1 5. VLR 1 2 3 4 ELETECH VOICE SYSTEMS

More information

User ID 150 Password - User ID 150 Password Mon- Cam-- Invalid Terminal Mode No User Terminal Mode No User Mon- Cam-- 2

User ID 150 Password - User ID 150 Password Mon- Cam-- Invalid Terminal Mode No User Terminal Mode No User Mon- Cam-- 2 Terminal Mode No User User ID 150 Password - User ID 150 Password Mon- Cam-- Invalid Terminal Mode No User Terminal Mode No User Mon- Cam-- 2 Mon1 Cam-- Mon- Cam-- Prohibited M04 Mon1 Cam03 Mon1 Cam03

More information

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

Windows 2000 Server for T100

Windows 2000 Server for T100 2 1 Windows 95/98 Windows 2000 3.5 Windows NT Server 4.0 2 Windows DOS 3.5 T200 2002 RAID RAID RAID 5.1 Windows 2000 Server T200 2002 Windows 2000 Server Windows 2000 Server Windows 2000 Server 3.5 for

More information

FSC-1713VNA Socket 478 CPU VGA/LAN/AUDIO

FSC-1713VNA Socket 478 CPU VGA/LAN/AUDIO FSC-1713VNA Socket 478 CPU VGA/LAN/AUDIO C 2003 2003 7 28 A0,,,,, FSC-1713VNA EVOC Microsoft Windows Microsoft Intel Pentium Intel, 1....1 1.1...1 1.2...2 1.3...4 1.4...6 2....7 2.1...7 2.2...8 2.3...9

More information

CHN_p000A_Cover.ai

CHN_p000A_Cover.ai NextoDI Co., Ltd. www.nextodi.com 列表........................................................................ 1 3 4 4 6 7 8 9 10 12 14 16 20 01 02 03 04 1 2 3 5 6 4 XCopy Ready B Menu Menu Off Off 05 06

More information

01CP-WX3030WNetc_CO_ENG.indd

01CP-WX3030WNetc_CO_ENG.indd Data Video Projector User s Manual (Concise) ModelS: 8928A/8930A/8931WA/ 8933W Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please

More information

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 B. 啟 用 智 慧 型 裝 置 的 無 線 Wi-Fi C. 選 擇 無 線 網 路 名 稱 "edimax.setup"

More information

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family small, speedy, safe Eextremely modular Up to 64 modules per bus de Quick reaction time: up to 20 µs A new Member of the Cube Family Murrelektronik s modular I/O system expands the field-tested Cube family

More information

(Load Project) (Save Project) (OffLine Mode) (Help) Intel Hex Motor

(Load Project) (Save Project) (OffLine Mode) (Help) Intel Hex Motor 1 4.1.1.1 (Load) 14 1.1 1 4.1.1.2 (Save) 14 1.1.1 1 4.1.2 (Buffer) 16 1.1.2 1 4.1.3 (Device) 16 1.1.3 1 4.1.3.1 (Select Device) 16 2 4.1.3.2 (Device Info) 16 2.1 2 4.1.3.3 (Adapter) 17 2.1.1 CD-ROM 2 4.1.4

More information

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn Xi III Zebra XI III 1 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn 230V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666

More information

版本:A0

版本:A0 104-1811CLDNA(B) PC/104-Plus 单板电脑 Embedded 104 Single Board Computer Version: C00 声明本手册包含的内容并不代表本公司的承诺, 本公司保留对此手册更改的权利, 且不另行通知 对于任何因安装 使用不当而导致的直接 间接 有意或无意的损坏及隐患概不负责 订购产品前, 请向经销商详细了解产品性能是否符合您的需求 EVOC 是研祥智能科技股份有限公司的注册商标

More information

Panaboard Overlayer help

Panaboard Overlayer help Panaboard Overlayer Image Capture Software for Electronic Whiteboard (Panaboard) ... 3... 5... 6... 13...14 Panaboard Overlayer 1. 2. 3. 4. 4-1. 4-2. [ / ] ( ) 4-3. 5. 6. 6-1. 6-2. [ / ] ( ) 7. Panaboard

More information

8193 CPU Card Setting 附录 CPU 卡的设置 8193 CPU Card Setting - 1 -

8193 CPU Card Setting 附录 CPU 卡的设置 8193 CPU Card Setting - 1 - 附录 - 8193 CPU 卡的设置 - 1 - 产品规格 总线类型 全长型 PICMG1.0 单板电脑 尺寸 : 338.6mm(L) x 122mm(W) (13.33 x4.8 ) PCI 总线规格, 适合 2.3 版本 CPU 类型 LGA775 封装 Intel(R) Pentium(R) D 或 Pentium(R) 4 处理器 1066/800/533MHz 前端总线 自动选择 CPU

More information

RAID RAID 0 RAID 1 RAID 5 RAID * (-1)* (/ 2)* No Yes Yes Yes SATA A. B. BIOS SATA C. RAID BIOS RAID ( ) D. RAID/AHCI ( ) S ATA S S D ( ) (

RAID RAID 0 RAID 1 RAID 5 RAID * (-1)* (/ 2)* No Yes Yes Yes SATA A. B. BIOS SATA C. RAID BIOS RAID ( ) D. RAID/AHCI ( ) S ATA S S D ( ) ( SATA... 2 RAID/AHCI... 16 Intel Optane... 19 Intel Virtual RAID on CPU (Intel VROC)... 21 RAID RAID 0 RAID 1 RAID 5 RAID 10 2 2 3 4 * (-1)* (/ 2)* No Yes Yes Yes SATA A. B. BIOS SATA C. RAID BIOS RAID

More information

SA-DK2-U3Rユーザーズマニュアル

SA-DK2-U3Rユーザーズマニュアル USB3.0 SA-DK2-U3R 2007.0 2 3 4 5 6 7 8 System Info. Manual Rebuild Delete RAID RAID Alarm Rebuild Rate Auto compare Temp Management Load Default Elapse time Event Log 0 2 3 4 2 3 4 ESC 5

More information

nf4 sli infinity 87100526S 1.p65

nf4 sli infinity 87100526S 1.p65 935-CK804A-044 87100526S 2 FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These

More information

Xear 3D USB CH-IN-2 SPKs 2 6 :

Xear 3D USB CH-IN-2 SPKs 2 6 : 13 6 CH-IN-2 SPKs 2 6 : 13 2003 7 0 13 Notice The content furnished in this document is C-Media audio product knowledge for customers reference However, C-Media Inc assumes no responsibility for the consequences

More information

Chapter 2 GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT") GBT GBT GBT

Chapter 2 GIGA-BYTE TECHNOLOGY CO., LTD. (GBT) GBT GBT GBT Chapter 2 GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT") GBT GBT GBT 2004 5 31-1 - 1.... 3 1.1....3 1.2. GV-R80P256D/GV-R80P256V...3 2.... 4 2.1....4 2.2....5 2.3....6 3.... 8 3.1. Win XP...8 3.1.1....8 3.1.2.

More information

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone,

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, respectively, and has been certified by the developer

More information

ARM JTAG实时仿真器安装使用指南

ARM JTAG实时仿真器安装使用指南 ARM JTAG Version 1.31 2003. 11. 12 ARM JTAG ARM JTAG.3 ARM 2.1.4 2.2.4 ARM JTAG 3.1 18 3.2 18 3.2.1 Multi-ICE Server.18 3.2.2 ADS..21 ARM JTAG 4.1 Multi-ICE Server 33 4.1.1 Multi-ICE Server..... 33 4.1.2

More information

Ch03_嵌入式作業系統建置_01

Ch03_嵌入式作業系統建置_01 Chapter 3 CPU Motorola DragonBall ( Palm PDA) MIPS ( CPU) Hitachi SH (Sega DreamCast CPU) ARM StrongARM CPU CPU RISC (reduced instruction set computer ) CISC (complex instruction set computer ) DSP(digital

More information

TITLE 标题 PAGE 页码 CONTENTS( 目录 )... 1 RECORD OF REVISIONS( 修改记录 )... 1 GENERAL DESCRIPTION( 整体概述 )... 2 FUNCTION LAYOUT( 产品外观图 )... 2 FEATURES( 产品特性 ).

TITLE 标题 PAGE 页码 CONTENTS( 目录 )... 1 RECORD OF REVISIONS( 修改记录 )... 1 GENERAL DESCRIPTION( 整体概述 )... 2 FUNCTION LAYOUT( 产品外观图 )... 2 FEATURES( 产品特性 ). TITLE 标题 PAGE 页码 CONTENTS( 目录 )... 1 RECORD OF REVISIONS( 修改记录 )... 1 GENERAL DESCRIPTION( 整体概述 )... 2 FUNCTION LAYOUT( 产品外观图 )... 2 FEATURES( 产品特性 )... 2 INTERFACE DEFINITION( 接口定义 )... 3 CONTROLLER DIMENSIONS(

More information

KL DSC DEMO 使用说明

KL DSC DEMO 使用说明 :0755-82556825 83239613 : (0755)83239613 : http://www.kingbirdnet.com EMAIL Good989@163.com 1 1 KB3000 DTU... 3 1.1... 3 1.2... 3 1.3... 3 1.4... 3 2... 4 2.1 GSM/GPRS... 4 2.2... 4 2.3... 5 2.4... 6 2.5...

More information

MICROCHIP EVM Board : APP APP001 PICmicro Microchip APP001 40pin PDIP PICmicro Design Tips Character LCM Temperature Sensor Application I/O Pi

MICROCHIP EVM Board : APP APP001 PICmicro Microchip APP001 40pin PDIP PICmicro Design Tips Character LCM Temperature Sensor Application I/O Pi MICROCHIP EVM Board : APP001 1-1. APP001 PICmicro Microchip APP001 40pin PDIP PICmicro Design Tips Character LCM Temperature Sensor Application I/O Pin 16 I/O Extension Interface 1-2. APP001 Block_A Block_B

More information

Microsoft Word - template.doc

Microsoft Word - template.doc HGC efax Service User Guide I. Getting Started Page 1 II. Fax Forward Page 2 4 III. Web Viewing Page 5 7 IV. General Management Page 8 12 V. Help Desk Page 13 VI. Logout Page 13 Page 0 I. Getting Started

More information

Windows RTEMS 1 Danilliu MMI TCP/IP QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos eco

Windows RTEMS 1 Danilliu MMI TCP/IP QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos eco Windows RTEMS 1 Danilliu MMI TCP/IP 80486 QEMU i386 QEMU ARM POWERPC i386 IPC PC104 uc/os-ii uc/os MMI TCP/IP i386 PORT Linux ecos Linux ecos ecos ecos Email www.rtems.com RTEMS ecos RTEMS RTEMS Windows

More information

1 CPU

1 CPU 2000 Tel 82316285 82317634 Mail liuxd@buaa.edu.cn 1 CPU 2 CPU 7 72 A B 85 15 3 1/2 M301 2~17 : 3/4 1/2 323 IBM PC 1. 2. 3. 1. 2. 3. 1.1 Hardware Software 1.2 M3 M2 M1 1.2 M3 M1 M2 M2 M1 M1 M1 1.2 M3 M1

More information

Ác Åé å Serial ATA ( nvidia nforce4-4x; nvidia nforce3 250/Ultra; nvidia nforce2 MCP RAID) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA

Ác Åé å Serial ATA ( nvidia nforce4-4x; nvidia nforce3 250/Ultra; nvidia nforce2 MCP RAID) S A T A (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA Serial ATA... ( nvidia nforce4-4x; nvidia nforce3 250/Ultra; nvidia nforce2 MCP RAID)...2 (1) SATA... 2 (2) B I O S S A T A... 3 (3) RAID BIOS RAID... 5 (4) S A T A... 8 (5) S A T A... 10 (6) Microsoft

More information

68369 (ppp quickstart guide)

68369 (ppp quickstart guide) Printed in USA 04/02 P/N 68369 rev. B PresencePLUS Pro PC PresencePLUS Pro PresencePLUS Pro CD Pass/Fails page 2 1 1. C-PPCAM 2. PPC.. PPCAMPPCTL 3. DB9D.. STPX.. STP.. 01 Trigger Ready Power 02 03 TRIGGER

More information

untitled

untitled Copyright 2008 2009/09 Microsoft MS-DOS Windows Windows Sound System Microsoft Corporation Intel Centrino Centrino Duo Pentium M Banias Calexico Intel Corporation Sound Blaster Sound Blaster Pro Creative

More information

audiogram3 Owners Manual

audiogram3 Owners Manual USB AUDIO INTERFACE ZH 2 AUDIOGRAM 3 ( ) * Yamaha USB Yamaha USB ( ) ( ) USB Yamaha (5)-10 1/2 AUDIOGRAM 3 3 MIC / INST (XLR ) (IEC60268 ): 1 2 (+) 3 (-) 2 1 3 Yamaha USB Yamaha Yamaha Steinberg Media

More information

Microsoft Word - 8011_TC_Lemel_new.doc

Microsoft Word - 8011_TC_Lemel_new.doc 筆 記 型 電 腦 使 用 手 冊 P/N: 5615 6854 0002 R00 (2004 年 10 ) 註 冊 商 標 所 品 牌 及 產 品 稱 所 登 記 之 商 標 屬 於 各 品 牌 及 產 品 稱 之 登 記 公 司 所 注 意 本 手 冊 之 內 容 本 公 司 享 隨 時 修 改 之 權 利, 且 不 另 行 通 知 目 錄 前 言... v 第 1 章 開 始 工 作...1-1

More information

邏輯分析儀的概念與原理-展示版

邏輯分析儀的概念與原理-展示版 PC Base Standalone LA-100 Q&A - - - - - - - SCOPE - - LA - - ( Embedded ) ( Skew ) - Data In External CLK Internal CLK Display Buffer ASIC CPU Memory Trigger Level - - Clock BUS Timing State - ( Timing

More information

untitled

untitled DOP www.deltaww.com DOP (RS232/RS485/ RS422) DOP USB SD 30 100 PLC Best Performance Huma Beautiful Display Beneficial Feature 1 DOP LED 65536 2D n Machine Interface s 2 DOP-B DOP-B 4.3 inches Wide B03S211

More information

5in1_eDVR_Manual_Chinese.cdr

5in1_eDVR_Manual_Chinese.cdr 02 English User Manual 29 User Manual Contents 2 5 6 7 8 9 10 11 12 14 17 18 19 20 21 22 23 24 25 26 27 Quick start Controls Accessories Minimum System Requirements Battery Charge Power On/Off LCM Indicator

More information

Desktop Management Guide

Desktop Management Guide Ĵ* 商 用 台 式 机 文 档 部 件 号 312947-AA1 2003 詤 3 本 指 南 介 绍 了 预 装 在 某 些 机 型 上 的 安 全 保 护 功 能 和 智 能 管 理 功 能 的 定 义 及 使 用 说 明 2002 Hewlett-Packard Company 2002 Hewlett-Packard Development Company, L.P. HP Hewlett

More information

HCD0174_2008

HCD0174_2008 Reliability Laboratory Page: 1 of 5 Date: December 23, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), suppo

Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), suppo GC-Thunderbolt 2 Installation Guide/ 12WE6-TH2-10AR Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), supporting

More information

Windows XP

Windows XP Windows XP What is Windows XP Windows is an Operating System An Operating System is the program that controls the hardware of your computer, and gives you an interface that allows you and other programs

More information

untitled

untitled XILINX Platform Cbale USB www.hseda.com ...... Platform Cable USB Compatible.................. impact.........1 platform Cable USB Compatible.........1...1...1...1...1...1 Platform Cable USB Compatible

More information

Announcement What contained in this User Manual does not represent the commitments of EVOC Company. EVOC Company reserves the right to revise this Use

Announcement What contained in this User Manual does not represent the commitments of EVOC Company. EVOC Company reserves the right to revise this Use EC5 1712CLDNA(B) Embedded Single Board Computer with CPU/LVDS/VGA/SSD/LAN/AUDIO Version: C00 Announcement What contained in this User Manual does not represent the commitments of EVOC Company. EVOC Company

More information

Microsoft Word - fa8553e.doc

Microsoft Word - fa8553e.doc FA-8553 Intel Pentium M /Intel Celeron M Embedded CPU Board USER S MANUAL (V1.0) 健昇科技股份有限公司 JS AUTOMATION CORP. 台北縣汐止市中興路 100 號 6 樓 6F,No.100,Chungshin Rd. Shitsu, Taipei, Taiwan, R.O.C. TEL:886-2-2647-6936

More information

GH1220 Hall Switch

GH1220 Hall Switch Unipolar Hall Switch - Medium Sensitivity Product Description The DH220 is a unipolar h all switch designed in CMOS technology. The IC internally includes a voltage regulator, Hall sensor with dynamic

More information

Microsoft Word - LR1122B-B.doc

Microsoft Word - LR1122B-B.doc UNISONIC TECHNOLOGIES CO., LTD LOW NOISE ma LDO REGULATOR DESCRIPTION The UTC is a typical LDO (linear regulator) with the features of High output voltage accuracy, low supply current, low ON-resistance,

More information

AN INTRODUCTION TO PHYSICAL COMPUTING USING ARDUINO, GRASSHOPPER, AND FIREFLY (CHINESE EDITION ) INTERACTIVE PROTOTYPING

AN INTRODUCTION TO PHYSICAL COMPUTING USING ARDUINO, GRASSHOPPER, AND FIREFLY (CHINESE EDITION ) INTERACTIVE PROTOTYPING AN INTRODUCTION TO PHYSICAL COMPUTING USING ARDUINO, GRASSHOPPER, AND FIREFLY (CHINESE EDITION ) INTERACTIVE PROTOTYPING 前言 - Andrew Payne 目录 1 2 Firefly Basics 3 COMPONENT TOOLBOX 目录 4 RESOURCES 致谢

More information

BA 2002, 3 IPCS WWW.EASTCATO.COM - - - - - -1-3 -15 - - - - - - WWW.EASTCATO.COM BA 1 2 3 4 20% DC12V A-1 WWW.EASTCATO.COM ok A-2 WWW.EASTCATO.COM RS232 RS485 EC-NET : B-1 WWW.EASTCATO.COM EC-NET 14 I/O

More information

!!

!! !! Noise Suppression by EMIFILr Application Guide Application Manual Cat.No.C35C !! 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 YYYYYYYYYYYYYYYYYYYYYY........................ YYYYYYYYYYYYYYYYYYYY........................

More information

untitled

untitled 020-101789-04 Roadie 4K35 2016 Christie Digital Systems USA Inc. ISO 9001 14001 a. b. c. d. DVD e. internet f. g. / h. i. j. LCD LCD LCD 5 8 k. l. LCD m. / (i) / (ii) FCC 15 A CAN ICES-3 (A) / NMB-3 (A)

More information

r_09hr_practical_guide_kor.pdf

r_09hr_practical_guide_kor.pdf PRACTICAL GUIDE TO THE EDIROL R-09HR 3 4 PRACTICAL GUIDE TO THE EDIROL R-09HR 5 Situation 1 6 1 2 3 PRACTICAL GUIDE TO THE EDIROL R-09HR WAV MP3 WAV 24 bit/96 khz WAV 16 bit/44.1 khz MP3 128 kbps/44.1

More information

2002/06/25

2002/06/25 2002/06/25 ... 1 GPU... 1 1.... 1 2.... 1 3.... 2 4.... 2 5.... 2 6. MX460... 3 6.1... 3 6.2... 4 7. MX440... 5 7.1... 5 7.2... 6 8. MX420... 7 8.1... 7 8.2... 8 9. MX420D... 9 9.1... 9 9.2... 10 10....11

More information

User’s Manual

User’s Manual SNAP 500 打 印 机 用 户 手 册 1 用 户 手 册 SNAP TM 500 打 印 机 2015 年 8 月 24 日 AVERY DENNISON Manual Edition 2.5 2 SNAP 500 打 印 机 用 户 手 册 WARNING This device complies with Part 15 of the FCC Rules. Operation is subject

More information