有关敝公司产品的注意事项 一般电子设备 / IMDRF IMDRF IMDRF

Transcription

1 有关敝公司产品的注意事项 一般电子设备 / IMDRF IMDRF IMDRF

2 电感器波峰焊 径向导线型电感器 PARTS 型号标示法 NUMBER *Operating Temp. : -25~+105 (Including self-generated heat) L H L 0 8 T B K =Blank 空格 space Series name Code LH 2 2Characteristics Code L LC Series name Radial leaded inductor Characteristics Standard type Taping available High current type 3 D 3Dimensions(D) Code Dimensions(D)[mm D mm max.] Packaging 4 Code NB TB Packaging Bulk(LHL) LHL Ammo LHL packaging(lhl) 5Nominal 5 inductance Code (example) Nominal inductance[μh] H 1R R=Decimal 小数点 point 6 6Inductance tolerance Code Inductance tolerance J ±5% K ±10% M ±20% N ±30% 7Internal 7 code Code Internal code Standard 电感器/导线型 STANDARD 标准外型尺寸 / EXTERNAL 标准数量 DIMENSIONS / STANDARD QUANTITY LHL /LHLC D H 2 d l F Type D H 2 l F φd LH L 08 LH LC08 LH L 10 LH LC max (0.354 max) 11.0 max (0.433 max) 9.5 max (0.374 max) 14.0 max (0.551 max) (0.197±0.039) (0.197±0.039) (0.197±0.039) (0.197±0.039) 0.6±0.05 (0.024±0.002) 0.6±0.05 (0.024±0.002) Standard quantity [pcs] [pcs] Box Bulk Taping mm inch Unit:mm(inch) 107

3 电感器/导线型电感器 PARTS 型号一览 NUMBER LHL08 Parts number EHS Nominal inductance H [μh] Inductance tolerance Q Q min. (min.) Self-resonant frequency MH [MHz](min..) min. DC Resistance [Ω](max.) max. Rated current A [A](max.) max. Measuring frequency MHz [MHz] LH L 08[]1R0N RoHS 1.0 ±30% LH L 08[]1R5M RoHS 1.5 ±20% LH L 08[]2R2M RoHS 2.2 ±20% LH L 08[]2R7M RoHS 2.7 ±20% LH L 08[]3R3M RoHS 3.3 ±20% LH L 08[]3R9M RoHS 3.9 ±20% LH L 08[]4R7M RoHS 4.7 ±20% LH L 08[]5R6M RoHS 5.6 ±20% LH L 08[]6R8M RoHS 6.8 ±20% LH L 08[]8R2M RoHS 8.2 ±20% LH L 08[]100K RoHS 10 ±10% LH L 08[]120K RoHS 12 ±10% LH L 08[]150K RoHS 15 ±10% LH L 08[]180K RoHS 18 ±10% LH L 08[]220K RoHS 22 ±10% LH L 08[]270K RoHS 27 ±10% LH L 08[]330K RoHS 33 ±10% LH L 08[]390K RoHS 39 ±10% LH L 08[]470K RoHS 47 ±10% LH L 08[]560K RoHS 56 ±10% LH L 08[]680K RoHS 68 ±10% LH L 08[]820K RoHS 82 ±10% LH L 08[]101K RoHS 100 ±10% LH L 08[]121K RoHS 120 ±10% LH L 08[]151K RoHS 150 ±10% LH L 08[]181K RoHS 180 ±10% LH L 08[]221K RoHS 220 ±10% LH L 08[]271K RoHS 270 ±10% LH L 08[]331K RoHS 330 ±10% LH L 08[]391K RoHS 390 ±10% LH L 08[]471K RoHS 470 ±10% LH L 08[]561K RoHS 560 ±10% LH L 08[]681K RoHS 680 ±10% LH L 08[]821K RoHS 820 ±10% LH L 08[]102J RoHS 1000 ±5% LH L 08[]122J RoHS 1200 ±5% LH L 08[]152J RoHS 1500 ±5% LH L 08[]182J RoHS 1800 ±5% LH L 08[]222J RoHS 2200 ±5% LH L 08[]272J RoHS 2700 ±5% LH L 08[]332J RoHS 3300 ±5% LH L 08[]392J RoHS 3900 ±5% LH L 08[]472J RoHS 4700 ±5% LH L 08[]562J RoHS 5600 ±5% LH L 08[]682J RoHS 6800 ±5% LH L 08[]822J RoHS 8200 ±5% LH L 08[]103J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]123J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]153J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]183J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]223J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]273J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 08[]333J RoHS ±5% L:1kHz, Q:0.0796MHz ( ) [] Please specify the packaging code. TB (TB: Taping, NB NB: Bulk) 108

4 PARTS 型号一览 NUMBER LHL10 Parts number EHS Nominal inductance H [μh] Inductance tolerance Q Q min. (min.) Self-resonant frequency MH [MHz](min..) min. DC Resistance [Ω](max.) max. Rated current A [A](max.) max. Measuring frequency MHz [MHz] LH L 10[]3R3M RoHS 3.3 ±20% LH L 10[]3R9M RoHS 3.9 ±20% LH L 10[]4R7M RoHS 4.7 ±20% LH L 10[]5R6M RoHS 5.6 ±20% LH L 10[]6R8M RoHS 6.8 ±20% LH L 10[]8R2M RoHS 8.2 ±20% LH L 10[]100K RoHS 10 ±10% LH L 10[]120K RoHS 12 ±10% LH L 10[]150K RoHS 15 ±10% LH L 10[]180K RoHS 18 ±10% LH L 10[]220K RoHS 22 ±10% LH L 10[]270K RoHS 27 ±10% LH L 10[]330K RoHS 33 ±10% LH L 10[]390K RoHS 39 ±10% LH L 10[]470K RoHS 47 ±10% LH L 10[]560K RoHS 56 ±10% LH L 10[]680K RoHS 68 ±10% LH L 10[]820K RoHS 82 ±10% LH L 10[]101K RoHS 100 ±10% LH L 10[]121K RoHS 120 ±10% LH L 10[]151K RoHS 150 ±10% LH L 10[]181K RoHS 180 ±10% LH L 10[]221K RoHS 220 ±10% LH L 10[]271K RoHS 270 ±10% LH L 10[]331K RoHS 330 ±10% LH L 10[]391K RoHS 390 ±10% LH L 10[]471K RoHS 470 ±10% LH L 10[]561K RoHS 560 ±10% LH L 10[]681K RoHS 680 ±10% LH L 10[]821K RoHS 820 ±10% LH L 10[]102J RoHS 1000 ±5% LH L 10[]122J RoHS 1200 ±5% LH L 10[]152J RoHS 1500 ±5% LH L 10[]182J RoHS 1800 ±5% LH L 10[]222J RoHS 2200 ±5% LH L 10[]272J RoHS 2700 ±5% LH L 10[]332J RoHS 3300 ±5% LH L 10[]392J RoHS 3900 ±5% LH L 10[]472J RoHS 4700 ±5% LH L 10[]562J RoHS 5600 ±5% LH L 10[]682J RoHS 6800 ±5% LH L 10[]822J RoHS 8200 ±5% LH L 10[]103J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]123J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]153J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]183J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]223J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]273J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]333J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]393J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]473J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]563J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]683J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]823J RoHS ±5% L:1kHz, Q:0.0796MHz LH L 10[]104J RoHS ±5% L:1kHz, Q:0.0252MHz LH L 10[]124J RoHS ±5% L:1kHz, Q:0.0252MHz LH L 10[]154J RoHS ±5% L:1kHz, Q:0.0252MHz ( ) [] [] Please specify the packaging code. TB (TB: Taping, NB NB: Bulk) 电感器/导线型 电感器 109

5 电感器/导线型电感器 PARTS 型号一览 NUMBER LHLC08 Parts number EHS Nominal inductance H [μh] Inductance tolerance Q Q min. (min.) Self-resonant frequency MH [MHz](min..) min. DC Resistance [Ω](max.) max. Rated current A [A](max.) max. Measuring frequency MHz [MHz] LH LC08[]1R0N RoHS 1.0 ±30% LH LC08[]1R5M RoHS 1.5 ±20% LH LC08[]2R2M RoHS 2.2 ±20% LH LC08[]2R7M RoHS 2.7 ±20% LH LC08[]3R3M RoHS 3.3 ±20% LH LC08[]3R9M RoHS 3.9 ±20% LH LC08[]4R7M RoHS 4.7 ±20% LH LC08[]5R6M RoHS 5.6 ±20% LH LC08[]6R8M RoHS 6.8 ±20% LH LC08[]8R2M RoHS 8.2 ±20% LH LC08[]100K RoHS 10 ±10% LH LC08[]120K RoHS 12 ±10% LH LC08[]150K RoHS 15 ±10% LH LC08[]180K RoHS 18 ±10% LH LC08[]220K RoHS 22 ±10% LH LC08[]270K RoHS 27 ±10% LH LC08[]330K RoHS 33 ±10% LH LC08[]390K RoHS 39 ±10% LH LC08[]470K RoHS 47 ±10% LH LC08[]560K RoHS 56 ±10% LH LC08[]680K RoHS 68 ±10% LH LC08[]820K RoHS 82 ±10% LH LC08[]101K RoHS 100 ±10% LH LC08[]121K RoHS 120 ±10% LH LC08[]151K RoHS 150 ±10% LH LC08[]181K RoHS 180 ±10% LH LC08[]221K RoHS 220 ±10% LH LC08[]271K RoHS 270 ±10% LH LC08[]331K RoHS 330 ±10% LH LC08[]391K RoHS 390 ±10% LH LC08[]471K RoHS 470 ±10% LH LC08[]561K RoHS 560 ±10% LH LC08[]681K RoHS 680 ±10% LH LC08[]821K RoHS 820 ±10% LH LC08[]102J RoHS 1000 ±5% LH LC08[]122J RoHS 1200 ±5% LH LC08[]152J RoHS 1500 ±5% LH LC08[]182J RoHS 1800 ±5% LH LC08[]222J RoHS 2200 ±5% LH LC08[]272J RoHS 2700 ±5% LH LC08[]332J RoHS 3300 ±5% LH LC08[]392J RoHS 3900 ±5% LH LC08[]472J RoHS 4700 ±5% LH LC08[]562J RoHS 5600 ±5% LH LC08[]682J RoHS 6800 ±5% LH LC08[]822J RoHS 8200 ±5% LH LC08[]103J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]123J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]153J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]183J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]223J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]273J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC08[]333J RoHS ±5% L:1kHz, Q:0.0796MHz ( ) [] Please specify the packaging code. TB (TB: Taping, NB NB: Bulk) 110

6 电感器型号一览 PARTS NUMBER LHLC10 Parts number EHS Nominal inductance H [μh] Inductance tolerance Q Q min. (min.) Self-resonant frequency MH [MHz](min..) min. DC Resistance [Ω](max.) max. Rated current A [A](max.) max. Measuring frequency MHz [MHz] LH LC10[]3R3M RoHS 3.3 ±20% LH LC10[]3R9M RoHS 3.9 ±20% LH LC10[]4R7M RoHS 4.7 ±20% LH LC10[]5R6M RoHS 5.6 ±20% LH LC10[]6R8M RoHS 6.8 ±20% LH LC10[]8R2M RoHS 8.2 ±20% LH LC10[]100K RoHS 10 ±10% LH LC10[]120K RoHS 12 ±10% LH LC10[]150K RoHS 15 ±10% LH LC10[]180K RoHS 18 ±10% LH LC10[]220K RoHS 22 ±10% LH LC10[]270K RoHS 27 ±10% LH LC10[]330K RoHS 33 ±10% LH LC10[]390K RoHS 39 ±10% LH LC10[]470K RoHS 47 ±10% LH LC10[]560K RoHS 56 ±10% LH LC10[]680K RoHS 68 ±10% LH LC10[]820K RoHS 82 ±10% LH LC10[]101K RoHS 100 ±10% LH LC10[]121K RoHS 120 ±10% LH LC10[]151K RoHS 150 ±10% LH LC10[]181K RoHS 180 ±10% LH LC10[]221K RoHS 220 ±10% LH LC10[]271K RoHS 270 ±10% LH LC10[]331K RoHS 330 ±10% LH LC10[]391K RoHS 390 ±10% LH LC10[]471K RoHS 470 ±10% LH LC10[]561K RoHS 560 ±10% LH LC10[]681K RoHS 680 ±10% LH LC10[]821K RoHS 820 ±10% LH LC10[]102J RoHS 1000 ±5% LH LC10[]122J RoHS 1200 ±5% LH LC10[]152J RoHS 1500 ±5% LH LC10[]182J RoHS 1800 ±5% LH LC10[]222J RoHS 2200 ±5% LH LC10[]272J RoHS 2700 ±5% LH LC10[]332J RoHS 3300 ±5% LH LC10[]392J RoHS 3900 ±5% LH LC10[]472J RoHS 4700 ±5% LH LC10[]562J RoHS 5600 ±5% LH LC10[]682J RoHS 6800 ±5% LH LC10[]822J RoHS 8200 ±5% LH LC10[]103J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]123J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]153J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]183J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]223J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]273J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]333J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]393J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]473J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]563J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]683J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]823J RoHS ±5% L:1kHz, Q:0.0796MHz LH LC10[]104J RoHS ±5% L:1kHz, Q:0.0252MHz LH LC10[]124J RoHS ±5% L:1kHz, Q:0.0252MHz LH LC10[]154J RoHS ±5% L:1kHz, Q:0.0252MHz ( ) [] Please specify the packaging code. TB (TB: Taping, NB NB: Bulk) 电感器/导线型 111

7 RADIAL LEADED INDUCTORS PACKAGING 1Minimum Quantity Type (EIA) Standard quantity [pcs] Bulk Taped LHL LHL LHLC LHLC Bulk dimensions LHL08, LHL10 Dimensions Type φd(max) H 2 (max) F * l φd ±0.05 LHL08 (0.354) (0.374) (0.197±0.039) (0.197±0.039) (0.024±0.002) ±0.05 LHL10 (0.433) (0.551) (0.197±0.039) (0.197±0.039) (0.024±0.002) Unit:mm(inch) *Measured at the base of the leads. D H 1 H H 2 P P 0 P 1 P 2 F h W W 0 W 1 W 2 D 0 φd t LHL08 φ9.0 max (φ0.354 max) 30.5 max (1.20 max) /-0.0 ( /-0.000) 9.5 max (0.374 max) 12.7±1.0 (0.500±0.039) 12.7±0.3 1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) /-0.2 ( /0.008) 0.0±2.0 (0.0±0.079) /-0.5 ( /-0.020) 12.5 min (0.492 min) 9.0±0.5 (0.354±0.020) 3.0 max 2 (0.118 max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) 1 Accumulated error for 20 pitches is 1mm. 2 Bonding tape must not protrude from the base tape. LHL10 φ11.0 max (φ0.433 max) 34.0 max (1.34 max) /-0.0 ( /-0.000) 14.0 max (0.551 max) 12.7±1.0 (0.500±0.039) 12.7±0.3 1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) /-0.2 ( /-0.008) 0.0±2.0 (0.0±0.079) /-0.5 ( /-0.020) 12.5 min (0.492 min) 9.0±0.5 (0.354±0.020) 3.0 max 2 (0.118 max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) Unit:mm(inch) i_leaded_lh_pack_e-e04r01

8 LHLC08, LHLC10 Dimensions Type φd(max) H 2 (max) F * l φd ±0.05 LHLC08 (0.354) (0.374) (0.197±0.039) (0.197±0.039) (0.024±0.002) ±0.05 LHLC10 (0.433) (0.551) (0.197±0.039) (0.197±0.039) (0.024±0.002) Unit:mm(inch) *Measured at the base of the leads. D H 1 H H 2 P P 0 P 1 P 2 F H W W 0 W 1 W 2 D 0 φd t LHLC08 φ9.0max (φ0.354max) 30.5max (1.20max) /-0.0 ( /-0.000) 9.5max (0.374max) 12.7±1.0 (0.500±0.039) 12.7±0.3 1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) /-0.2 ( /-0.008) 0.0±2.0 (0.0±0.079) /-0.5 ( /-0.020) 12.5min (0.492min) 9.0±0.5 (0.354±0.020) 3.0max 2 (0.118max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) 1 Accumulated error for 20 pitches is 1mm. 2 Bonding tape must not protrude from the base tape. LHLC10 φ11.0max (φ0433max) 34.0max (1.34max) /-0.0 ( /-0.000) 14.0max (0.551max) 12.7±1.0 (0.500±0.039) 12.7±0.3 1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) /-0.2 ( /-0.008) 0.0±2.0 (0.0±0.079) /-0.5 ( /-0.020) 12.5min (0.492min) 9.0±0.5 (0.354±0.020) 3.0max 2 (0.118max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) Unit:mm(inch) i_leaded_lh_pack_e-e04r01

9 AXIAL LEADED INDUCTORS(CAL Type) RADIAL LEADED INDUCTORS(LH Type) LEADED FERRITE BEAD INDUCTORS( FB Series A Type/R Type) RELIABILITY DATA 1. Operating temperature Range -25~+ 105 Including self-generated heat 2. Storage temperature Range -40~+ 85 (Except for taping condition) 3. Rated current Within the specified tolerance : The maximum DC value having inductance within 10% and temperature increase within 40 by the application of DC bias. : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10:within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25 (LHL08, LHL10) : 40 (LHLC08, LHLC10) : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value. This is not guaranteed for electrical characteristics during current application. 4. Impedance : Measuring equipment Measuring frequency Within the specified tolerance : Impedance analyzer (HP4191A) or its equivalent : Specified frequency 5. Inductance : Measuring equipment Measuring frequency : Measuring equipment Measuring frequency Within the specified tolerance : LCR meter (HP4285A + HP42851A or its equivalent) : Specified frequency : LCR meter (HP4285A+HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency i_leaded_reli_e-e06r01

10 6. Q Measuring equipment Measuring frequency Within the specified tolerance : LCR meter (HP4285A+HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency 7. DC Resistance Measuring equipment : DC ohmmeter Within the specified tolerance 8. Self resonance frequency Measuring equipment Within the specified tolerance : (HP4191A, 4192A) its equivalent 9. Temperature characteristic L/L : Within ±7% Change of maximum inductance deviation in step 1 to 5 Temperature ( ) Step Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature Tensile strength test No abnormality such as cut lead, or looseness. : Apply the stated tensile force progressively in the direction to draw terminal. force (N) duration (s) : Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter tensile φd (mm) force (N) duration (s) 0.3<φd <φd ±5 0.8<φd : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the of the component during 10±1 seconds. axial direction i_leaded_reli_e-e06r01

11 11. Over current : Measuring current Number of measuring : Rated current 2 : 5 min. : one time No emission of smoke no firing. There shall be no scorch or short of wire. LHLC08, LHLC10 : There shall be no firing. 12. Terminal strength : bending No abnormality such as cut lead, or looseness. : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight 0.3< φ d < φ d : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight 0.3<φd <φd <φd Insulation resistance : between the terminals and body : Applied voltage : 500 VDC : 60 sec. 100MΩmin. 14. Insulation resistance : between terminals and core : Applied voltage : 100 VDC : 60±5 sec. 1MΩmin. 15. Withstanding : between the terminals and body : According to JIS C Metal global method Applied voltage : 500 VDC : 60 sec. No abnormality such as insulation damage i_leaded_reli_e-e06r01

12 16. DC bias characteristic L/L : Within -10% : Measure inductance with application of rated current using LCR meter to compare it with the initial value. 17. Body strength : Applied force :50N : 10 sec. Speed : Shall attain to specified force in 2 sec. FBA : Applied force : 50±3N : 30±1 sec. No abnormality as damage. No abnormality such as cracks on body. 18. Resistance to vibration L/L : Within ±5% Appearance : No abnormality L/L : Within ±5% Q change : Within ±30% Appearance : No abnormality Impedance change : Within ±20% : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. 19. Resistance to shock : Drop test Impact material Height Total number of drops No significant abnormality in appearance : concrete or vinyl tile : 1m : 10 times i_leaded_reli_e-e06r01

13 20. Solderability At least 75% of terminal electrode is covered by new solder. At least 75% of terminal electrode is covered by new solder. At least 90% of terminal electrode is covered by new solder. : Solder temperature : 230±5 : 2±0.5 sec. : Solder temperature : 235±5 : 2±0.5 sec. Immersion depth : Up to 1.5mm from bottom of case. : Solder temperature : 230±5 : 3±1 sec. Immersion depth : Up to 1.5mm from terminal root. 21. Resistance to soldering heat L/L : Within ±5% No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30% No significant abnormality in appearance Impedance change : Within ±20% : Solder temperature : 270±5 : 5±0.5 sec. One time Immersed conditions : Inserted into substrate with t=1.6mm Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. : Solder bath method : Solder temperature : 260±5 : 10±1 sec. : Up to 1.5mm from the bottom of case. Manual soldering : Solder temperature : 350±10 (At the tip of soldering iron) : 5±1 sec. : Up to 1.5mm from the bottom of case. Caution : No excessive pressing shall be applied to terminals. Recovery : 1 to 2hrs of recovery under the standard condition after the test. : Solder bath method: Condition 1: Solder temperature : 260±5 : 10±1 sec. Immersion depth : Up to 1.5mm from the terminal root. Condition 2 : Solder temperature : 350±5 : 3±1 sec. Immersion depth : Up to 1.5mm from the terminal root. Recovery : 3hrs of recovery under the standard condition after the test. 22. Resistance to solvent Please avoid the ultrasonic cleaning of this product. No significant abnormality in appearance Impedance change : Within ±20% : Solvent temperature : 20~25 : 30±5 sec. Solvent type : Acetone Recovery : 3hrs of recovery under the standard condition after the test. i_leaded_reli_e-e06r01

14 23. Thermal shock L/L : Within ±10% Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% Appearance : No abnormality Impedance change : Within ±20% :Conditions for 1cycle Step Temperature ( ) (min.) /-3 30±3 2 Room temperature Within /-0 30±3 4 Room temperature Within 3 Number of cycles Recovery : 5 cycles : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. : According to JIS C Conditions for 1 cycle Step Temperature ( ) (min.) 1 Minimum operating temperature 30±3 2 Room temperature Within 3 3 Maximum operating temperature 30±3 4 Room temperature Within 3 Number of cycles : 10 cycles Recovery : 5 cycles (FBA/ FBR) : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. : 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR) 24. Damp heat L/L : Within ±10% Appearance:No abnormality Impedance change:within ±20% : Temperature : 40±2 Humidity : 90~95%RH : 1000 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : Temperature : 60±2 Humidity : 90~95%RH : 1000 hrs Recovery : 3hrs of recovery under the standard condition after the removal from the test chamber. i_leaded_reli_e-e06r01

15 25. Loading under damp heat L/L : Within ±10% Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% : Temperature : 40±2 Humidity : 90~95%RH : 1000 hrs Applied current : Rated current Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : Temperature : 40±2 Humidity : 90~95%RH : /-0 hrs Applied current : Rated current Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 26. Loading at high temperature L/L : Within ±10% : Temperature : 85±2 : 1000 hrs Applied current : Rated current Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test L/L : Within ±10% : Temperature Recovery : Temperature Recovery Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% : -25±2 : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. :-40±3 : /-0 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 28. High temperature life test Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% : Temperature : 105±2 : /-0 hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. i_leaded_reli_e-e06r01

16 AXIAL LEADED INDUCTORS(CAL Type) RADIAL LEADED INDUCTORS(LH Type) LEADED FERRITE BEAD INDUCTORS(FB Series A Type/R Type) PRECAUTIONS 1. Circuit Design Precautions Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions Technical considerations Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Considerations for automatic placement Precautions Technical considerations Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions Technical considerations Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. Recommended conditions for using a soldering iron: Put the soldering iron on the land-pattern. Soldering iron's temperature - Below seconds or less The soldering iron should not directly touch the inductor. Reflow soldering 1. As for reflow soldering, please contact our sales staff. Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions Technical considerations Cleaning conditions 1. CAL type, LH type Please do not do cleaning by a supersonic wave. Cleaning conditions 1. CAL type, LH type, If washing by supersonic waves, supersonic waves may deform products. i_leaded_prec_e-e02r01

17 6. Handling Precautions Technical considerations Handling 1. Keep the inductors away from all magnets and magnetic objects. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type If inductors are dropped onto the floor or a hard surface they should not be used. Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). Handling 1. There is a case that a characteristic varies with magnetic influence. Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. LH type There is a case to be broken by a fall. Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Precautions Technical considerations Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature 0~40 Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. i_leaded_prec_e-e02r01