SP-MP-E3 USER S MANUAL V1.0 Beijing Spirit Technology Development Co.,Ltd

Transcription

1 SP-MP-E3 USER S MANUAL V1.0 Beijing Spirit Technology Development Co.,Ltd

2 CONTENT 1,Outer Appearance and Model No... 错误! 未定义书签 2,Interface definition and description... 错误! 未定义书签 3,Characteristic Specification... 错误! 未定义书签 4,Operation instruction ,Printing command... 8 HT... 错误! 未定义书签 LF... 错误! 未定义书签 FF... 错误! 未定义书签 CR... 错误! 未定义书签 DLE EOT n... 错误! 未定义书签 ESC SP n... 错误! 未定义书签 ESC! n... 错误! 未定义书签 ESC $ nl nh... 错误! 未定义书签 ESC % n... 错误! 未定义书签 ESC & y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)]... 错误! 未定义书签 ESC * m nl nh d1... dk... 错误! 未定义书签 ESC - n ESC 2... 错误! 未定义书签 ESC 3 n... 错误! 未定义书签 ESC = n... 错误! 未定义书签 ESC? n... 错误! 未定义书签 错误! 未定义书签 ESC D n1...nk NUL ESC E n... 错误! 未定义书签 ESC G n... 错误! 未定义书签 ESC J n... 错误! 未定义书签 ESC M n... 错误! 未定义书签 ESC R n... 错误! 未定义书签 ESC V n... 错误! 未定义书签 ESC \ nl nh... 错误! 未定义书签 ESC a n... 错误! 未定义书签 ESC c 5 n... 错误! 未定义书签 ESC d n... 错误! 未定义书签 ESC t n... 错误! 未定义书签 ESC { n... 错误! 未定义书签 FS P n... 错误! 未定义书签 GS! n... 错误! 未定义书签 GS * x y d1...d(x y 8) GS / m... 错误! 未定义书签 GS B n... 错误! 未定义书签

3 GS H n... 错误! 未定义书签 GS L nl nh... 错误! 未定义书签 GS P x y GS V m 2 GS V m n... 错误! 未定义书签 GS W nl nh GS f n... 错误! 未定义书签 GS h n... 错误! 未定义书签 1GS k m d1...dk NUL2 GS k m n d1...dn... 错误! 未定义书签 GS w n... 错误! 未定义书签 FS! n... 错误! 未定义书签 FS &... 错误! 未定义书签 FS - n... 错误! 未定义书签 FS.... 错误! 未定义书签 FS 2 c1 c2 d1...dk... 错误! 未定义书签 FS C n... 错误! 未定义书签 FS S n1 n FS W n... 错误! 未定义书签 Appendix A: CODE 错误! 未定义书签 Appendix B:The black mark Pre-print regulations... 错误! 未定义书签

4 1, Outer Appearance and Model No. 1, Outside view FEED button(indicator) Installation ear Open button 2, Dimensional drawing

5 Embedded open size:103mm*95mm 2, Interface definition and description 2.1 Interface appearance

6 USB port socket COM1serial port COM2 serial port Power socket 2.2 The pin definition of serial port RME3 serial port have COM1 and COM2,both of them use IDC-10 socket,their function are the same,only the definition order of ports are different,specific pins definition is as figure1and figure 2.Notice: Don t use two sockets at the same time Signal Pin No. Source Description TXD 2 Printer Printer transmits data to host RXD 3 Host Printer receives data from host CTS 8 Printer Printer and host hardware flow control signal busy signal DSR 6 Printer As CTS GND 5 - Figure 1 serial COM1 of RME3 series interface socket pins definition Signal Pin No. Source Description TXD 3 Printer Printer transmits data to host RXD 5 Host Printer receives data from host CTS 6 Printer Printer and host hardware flow control signal busy signal DSR 2 Printer As CTS GND 9 - Figure 2 serial COM2 of RME3 series interface socket pins definition

7 3, Characteristic Specification 3.1 Printing capability: Printing method :Line thermal Paper width:58mm; Printing width:48mm; Resolution:8dots/mm(203dpi); Dots per line:384dots; Printing speed :Max 100mm/S(<=25% printing dots); Paper thickness:60~80μm; Printable content:gb18030 all Chinese and characters, BIG5 Traditional Chinese characters, ASCII, self-defining character,one-dimensional bar code, Support different density map and downloading bitmap printing. 3.2 Power supply: DC 9~24V±10%,2A 3.3 paper specification: (1) Paper type: thermal (2) Printing width: 58mm (3) Paper thickness: 0.06~0.08 mm (4) Paper supply method: Drop-in easy loading (5) Cutting method: Auto cutting ( Full/Partial cut) 4, Operating instruction 4.1 Button and indicator description There are one button(feed button)and one indicator, the indicator is red. The meanings of indicator are as below: Light constant on: print unit is on Light flashing: printer has mistakes. Different types of mistake, different ways of flashing 1. The mistake can be automatically recovered when the indicator continuous flashing. Including the temperature mistake of printer head and opening of paper case cover. Error Description The flashing way of ERROR ERROR Temperature of printer head The temperature of printer head is too high, it will recover automatically when the temperature is normal Out of paper errors After installed the paper, it will recover automatically when out of paper. 2. The mistake can be automatically recovered when the indicator continuous flashing.

8 Including the temperature mistake of printer head and opening of paper case cover. Error Description The flashing way of [ERROR] ERROR Memory The printer can not work normally after the memory need to be read-write calibration Over voltage The voltage of power is too high Owe voltage The voltage of power is too low The CPU execution Temperature detection circuit The CPU execution to the wrong address Connection of temperature detection circuit connection error 4.2 Self-Test After receiving the printer, user can check its current setting and status at anytime. Self-test way is as below: Power off, then hold down the FEED button and press the power button at the same time. Then restart the printer. 5, Printing Command ---> DLE EOT n Real time transmission status ---> [Format] ASCII DLE EOT n Hex n Decimal 16 4 n ---> [Range] 1 n 4 ---> [Description] Sending the printer state that designated by parameter n just in time ---> When printer receives the command, returns to the interrelated status ---> [Reference] immediately HT Horizontal tab [Format] ASCII HT Hex 09 Decimal 9 [Description] Moves the print position to the next horizontal tab position. This command is ignored unless the next horizontal tab position has been set.

9 If the next position of horizontal tab exceeds the printing area, the current position will be set as [printing width+1]. Horizontal tab positions are set with ESCD. If the current position is at [printing width+1] when receives the command, the printer will carry out the action in row buffer and move the printing position to the Zero position of next line. The default value of tab position is every 8 standard ASCII characters (12*24) a tab. When the current row buffer is full, the printer will carry out the action below: Under standard mode, printer prints the content of current row and sets the Printing position at the zero position of next line Under page mode, the printer begins a new line and set the printing position at the zero position of next line. [Reference] ESC D LF Printing and feeding line [Format] ASCII LF Hex 0A Decimal 10 [Description] Printing the data in the print buffer and feeds one line This command sets the print position to the beginning of the line. [Reference] ESC 2, ESC 3 FF Printing and feeding paper [Format] ASCII FF Hex 0C Decimal 12 [Description] Printing all of the content in print buffer and returning to the standard mode, under the standard mode, if the printer establishes in the black mark paper mode, then printing the data in the buffer to feed paper to the black mark section, if haven t black mark, then feed the paper 30cm behind stop,the pre-print black mark specification is showed in the appendix C.the pre-print black mark instruction.if not at the black mark examing status and then only print the contents of buffer,don t feed paper. Clearing the content in print buffer after printing. The printing area setup by ESC W returns to the default The printer won t cut paper. This command sets the current position at the beginning of the line [Reference] ESC FF, ESC L, ESC S

10 CR Printing and entering [Format] ASCII CR Hex 0D Decimal 13 [Description] The same as LF when the command is permitted, if not, it will be ignored. Setting the printing position at the beginning of the line. The command is ignored under the serial interface mode. The printer allocation decides If the command is enabled under parallel mode. [Reference] LF DLE EOT n Real time status transmission [Format] ASCII DLE EOT n [Range] 1 n 4 [Description] Hex n Decimal 16 4 n Sending the printer state that designated by parameter n just in time: n=1:sending state of the printer n=2:sending off line state n=3:sending error state n=4:sending state of paper sensor -When printer receives the command, returns to the interrelated status immediately Avoiding to put this command in the command sequence of more than 2 characters. This command will be also valid even though the printer is set to forbid by the Command of ESC=(selecting peripheral ). When sending printer current state, each state is indicated by 1 byte Transmission state value of the printer can not confirm whether the master computer received Printer will carry out the command immediately once received This command is just available to the serial printer. The printer will carry out the command immediately under any state n = 1: Printer state Bit 0/1 HEX Decimal Function Fix as Fix as The cash box open/close signal is low(the third of cash box plug leads foot)

11 The cash box open/close signal is high(the third of cash box plug leads foot) online offline Fix as 1 5,6 undefined Fix as 0 n = 2: Off line state Bit 0/1 HEX Decimal Function fix as fix as close the top cover open the top cover Not holding down the feed button holding down the feed button fix as Printer is not out of paper Printer is out of paper No error state error state fix as 0 n = 3: error state Bit 0/1 HEX Decimal Function Fix as Fix as undefined noun cutter error cutter error Fix as noun unrecoverable error have unrecoverable error noun auto recoverable error have auto recoverable error Fix as 0 n = 4: paper sensor state Bit 1/0 HEX Decimal Function Fix as Fix as 1 2, The sensor of paper is going out: have enough paper 1 0C 12 The sensor of paper is going out:the paper is going out Fix as 1

12 5, lack of paper sensor: have paper lack of paper sensor: noun paper Fix as 0 [Reference] DLE ENQ, GS a, GS r ESC SP n Setting the right space of characters [Format] ASCII ESC SP n Hex 1B 20 n Decimal n [Range] 0 n 255 [Description] Setting the right space of character for [n*units of vertial or lateral shifting] -When the character enlarges, the space enlarges the same times. -The command doesn t affect the setup of Chinese characters. -The value which is set by the command under page and standard mode is mutual independence. -Units of vertial or lateral shifting area pointed by GSP. Changing units of vertial or lateral shifting does not change the current right space. -Using lateral shifting units under standard mode. -According to the direction of printing area and the beginning position to select vertical or lateral shifting units under page mode. The selection modes areas below: 1 Using lateral shifting when the beginning position is the top left or lower right corner of the printing area which is set by ESC T; 2 Using vertical shifting when the beginning position is the lower left or top right corner of the printing area which is set by ESC T; The maximum right space is 255/203 inches. If setting beyond this value, it will automatically change into the maximum distance. [Default] n = 0 [Reference] ESC! n GS P selecting print mode [Format] ASCII ESC! n [Range] 0 n 255 [Description] Hex 1B 21 n Decimal n Setting character print mode according to value of n

13 Bit 1/0 HEX Decimal Function Standard ASCII style A (12 24) Compressing ASCII style B(9 17) 1,2 Undefined Cancel bold font Select bold font Cancel double height mode Select double height mode Cancel double width mode Select double width mode 6 Undefined Cancel underline mode Select underline mode -When selected double-height or double-width mode, double size characters are printed. -Any character can be added underline except the space set by HT and the characters clockwise 90 degrees. -Underline is not related to characters but confirmed by ESC-. -When some characters in a line are double or more height, all the characters on the line are aligned at the baseline. -ESC E can also select or cancel bold font. However, the command of the setting of the last received command is effective. -ESC- can also turn on or off underline mode. However, the setting of the last received command is effective. -GS! can also set the character boundary. However,the setting of the last received command is effective. Bold font is effective for character and Chinese, except bold font, other modes is only effective for character. [Default] n = 0 [Reference] ESC -, ESC E, GS! ESC $ nl nh Setting absolute print position [Format] ASCII ESC $ nl nh [Range] 0 nl 255 [Description] [Reference] Hex 1B 24 nl nh Decimal nl nh 0 nh 255 Setting the distance from the beginning of the line to the position at which (nl+nh 256) (vertical or horizontal motion unit) This command is ignored if the setting position is out of the printing area. Vertical and horizontal motion units are set by GSP. Using horizontal motion units under standard mode.

14 Under page mode, selecting to use vertical or horizontal motion units according to the direction of printing area and zero position. The system of selection is as below: 1 Using horizontal shifting when the beginning position is the top left or lower right corner of the printing area which is set by ESC T; 2 Using vertical shifting when the beginning position is the lower left or top [Reference] right corner of the printing area which is set by ESC T; ESC \, GS $, GS \, GS P ESC % n Selecting/Canceling self defined character [Format] ASCII ESC % n [Range] [Description] [Default] n = 0 Hex 1B 25 n Decimal n 0 n 255 Selecting/Canceling self-defined character When n(lsb)=0,cancel user-defined character set. When n(lsb)=1,select user-defined character set. When cancel user-defined character set, auto select built-in character set. n only LSB is available. [Reference] ESC &, ESC? ESC & y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)] Define user defined character [Format] ASCII ESC & y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)] Hex 1B 26 y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)] Decimal y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)] [Range] y = 3 32 c1 c x 12 standard ASCII style A(12 24) 0 x 9 compressing ASCII style B (9 17) 0 d1... d(y xk) 255 [Description] Define user defined character y specify the vertical byte number c1 specify the code of initial character,c2 specify the code of terminal character. x specify the vertical byte number The code range of defined character: from<20>hto<7e>h.(95 characters) Can define the continuous codes for several characters. When only one character is needed,c1=c2. d is the dot data of the character. Data of each dot begins from the left. Defining the data of user defined character is (y x)bytes. Setting the printing dot s corresponding bit is 1 or nonprinting dot s one is 0.

15 The user defined characters will be deleted in the following situation: 1 is carried out 2 ESC? is carried out 3 The printer reset or power off. Only the MSB is valid at the vertical third byte when the selt-defined characters are style B(9*17) [Default] Built in character set. [Reference] ESC %, ESC? [Example] When select the standard ASCII style(12 24) When select the compressing ASCII style (9 17)

16 ESC * m nl nh d1... dk Selecting bit map mode [Format] ASCII ESC * m nl nh d1...dk Hex 1B 2A m nl nh d1...dk Decimal m nl nh d1...dk [Range] m = 0, 1, 32, 33 0 nl nh 3 0 d 255 [Description] Selects a bit map mode appointed by m for the number of dots specified by nl and nh, as follows: m Mode Vertical Horizontal dots Dpi Dpi No.of datas(k) 0 8SD 8 68 DPI 101 DPI nl + nh DD 8 68 DPI 203 DPI nl + nh SD DPI 101 DPI ( nl + nh 256) DD DP 203 DPI ( nl + nh 256) 3 If the value of m goes beyond the range,nl and the datas later will be regarded as normal data to deal with. The dots number of horizontal printing depends on nl and nh,total number is nl+nh 256.

17 The part of the bit map that goes beyond the current area will be cut off d is the data of bit map. Printing when the relevant position of every byte is1,and when it is 0,will not print this point. mode of normal data processing after send the data of bit map. Except inversion mode, this command will not be influenced by other modes. (black double print underline enlarge character and invert) Relationship between data and printing point is as below: choosing 8 dots density: choosing 24 dots density:

18 ESC - n Select/cancel underline [Format] ASCII ESC - n Hex 1B 2D n Decimal n [Range] 0 n 2, 48 n 50 [Description] n [Default] n = 0 [Reference] ESC! Selecting or canceling the underline mode according to the value of n Function 0, 48 Cancel underline mode 1, 49 Select underline mode(1dot width) 2, 50 Select underline mode(2 dots width) Underline can be added under all characters(including right spacing),but not including the space set by HT The underline can not act on the characters of clockwise 90 degrees and inverting The width of the underline will not be changed, and the character rest will not be underlined when cancel the underline mode. The default width is1dot width. Changing the character boundary will not influence the current underline width Selecting/canceling the underline can also be set by ESC!. However, the setting of the last received command is effective. The command doesn t affect the Chinese character setting.

19 ESC 2 Setting default height of line [Format] ASCII ESC 2 [Description] [Reference] ESC 3 ESC 3 n Hex 1B 32 Decimal Selecting32 dots(4mm,about 1 7inch)line height Line height is independent under standard and page mode Setting the height of the line [Format] ASCII ESC 3 n [Range] 0 n 255 [Default value] [Reference] ESC = n Hex 1B 33 n Decimal n Setting[n*units of vertial or lateral shifting]inches as the height of the line Setting[n*units of vertial or lateral shifting]inches as the height of the line Units of vertial or lateral shifting are set by GSP,changing this setting will not influences current height of line Using vertical shifting units under standard mode According to the direction of printing area and the beginning position to select lateral or vertical shifting units under page mode.the selection modes are as below: 1 Using vertical shifting when the beginning position is the top left or lower right corner of the printing area which is set by ESC T; 2 Using lateral shifting when the beginning position is the lower left or top right corner of the printing area which is set by ESC T; The maximum distance of feeding paper is 1016mm(40inches).If it is beyond this distance, taking the maximum distance. The default height of line is 4mm(about1/6inch) ESC 2, GS P Selecting printer [Format] ASCII ESC = n [Range] 0 n 1 [Description] Hex 1B 3D n Decimal n Selecting printer, the printer selected can receive the data sent by main computer: Bit 1/0 Hex Decimal Function Forbidding printer Permitting printer

20 1-7 Undefined When the printer is forbidden, the printer ignores all the commands(dle EOT, DLE ENQ, DLE DC4)except real time command until the command is allowed. [Default value] n = 1 ESC? n cancel user self-defined character [Format] ASCII ESC? n Hex 1B 3F n Decimal n [Range] 32 n 127 [Description] Cancel user self-defined character Cancel the character code n of user self-defined character. The character use in character after canceling. The command deletes from the matrix which is selected by the mould concentrates to the specified code of the selective ESC! The command is ignored if the self-defined characters have no the character. [Reference] ESC &, ESC % Initializing the printer [Format] ASCII Hex 1B 40 Decimal [Description] Clearing the data in the printing buffer; The printing mode is set to the default The DIP switch set does not test again. Retaining the content in command buffer Retaining the macro definition Flash bit map is not erased Flash user data is not erased Servicing counter value is not erased The set value specified by GS(E is not erased. ESC D n1...nk NUL Setting horizontal tab positions [Format] ASCII ESC D n1... nk NUL Hex 1B 44 n1...nk 00 Decimal n1...nk 0 [Range] 1 n1 n2 nk k 32

21 [Description] [Default] [Reference] Setting horizontal tab positions N specifies the column number for setting a horizontal tab position from the beginning of the line. There are k tab positions. Horizontal tab positions can be gotten by the following formula: The horizontal tab position is stored as a value of [character width n]measured from the beginning of the line. The character width includes the right side character spacing, and double width characters are set with twice the width of normal characters. This command cancels the previous horizontal tab settings. When setting n=8,the print position is moved to column 9 Up to 32 tab positions(k=32)can be set. Data exceeding32tab positions is processed as normal data Tab position is ordered by asceding and the end mark is NUL When[n]k is less than or equal to the preceding value[n]k-1,tab setting is finished and the following data is processed as normal data. ESC D NUL cancels all horizontal tab positions. The previously specified horizontal tab positions do not change,even if the character width changes The character width is independence under standard and page mode The default tab positions are at intervals of 8 characters for font A(12 24). HT ESC E n Select/Cancel bold font print [Format] ASCII ESC E n [Range] 0 n 255 [Description] Hex 1B 45 n Decimal n Select/Cancel bold font print When the lowest bit of n is 0,cancel bold font print When the lowest bit of n is1,select bold font print Only the lowest bit of n is effective. Selecting/canceling bold font print can also be set by ESC!. However, the setting of the last received command is effective. [Default value] n = 0 [Reference] ESC! ESC G n Selecting/canceling double print mode [Format] ASCII ESC G n Hex 1B 47 n Decimal n

22 [Range] 0 n 255 [Description] Selecting/canceling double print mode When the lowest bit of n is 0,canceling double print mode When the lowest bit of n is 1,selecting double print mode Only the lowest bit of n is effective. The effect of this command is the same as bold font printing. [Default value] n = 0 [Reference] ESC E ESC J n Printing and feeding paper [Format] ASCII ESC J n Hex 1B 4A n Decimal n [Range] 0 n 255 [Description] Printing datas in print buffer and feeding paper for [n*units of vertial or lateral shifting] inches [ 注释 ] The current print position will be set to the beginning of the line after printing. The ESC 2 and ESC 3 commands set does affect the feeding distance. Units of vertial or lateral shifting are set by GSP Using vertical shifting units under standard mode According to the direction of printing area and the beginning position to select vertical or lateral shifting units under page mode.the selection modes are as below: 1 Using vertical shifting when the beginning position is the top left or lower right corner of the printing area which is set by ESC T; 2 Using lateral shifting when the beginning position is the lower left or top right corner of the printing area which is set by ESC T; The maximum distance of feeding paper is 1016mm(40inches).If it is beyond this distance, taking the maximum distance. [Reference] GS P ESC M n select font [Format] ASCII ESC M n Hex 1B 4D n Decimal n [Range] n = 0, 1,48, 49 [Description] select font n function 0,48 select standard ASCII style(12*24) 1,49 select compressing ASCII style (9*17) [Default value] n = 0

23 ESC R n Selecting international character set [Format] ASCII ESC R n Hex 1B 52 n Decimal n [Range] 0 n 15 [Description] Selecting a n international character set from the table below [Default] [Reference] n Character Set 0 U.S.A. 1 France 2 Germany 3 U.K. 4 DenmarkⅠ 5 Sweden 6 Italy 7 Spain Ⅰ 8 Japan 9 Norway 10 Denmark Ⅱ 11 Spain Ⅱ 12 Latin 13 Korea 14 Slovenia/Croatia 15 China n = 15 [GBK] n = 0 [the model except GBK] ESC V n Selecting/canceling character 90 clockwise. [Format] ASCII ESC V n Hex 1B 56 n Decimal n [Range] 0 n 1, 48 n 49 [Description] Selecting/canceling character 90 clockwise Value of n: n Function 0,48 canceling character 90clockwise 1,49 selecting character 90clockwise This command is just effective under standard mode.

24 [Default value] n = 0 The underline will be not 90 clockwise when select the underline mode. The double height and double width under 90 clcokwise are in opposite direction with the m under the normal mode. [Reference] ESC!, ESC - ESC \ nl nh Setting relative printing position [Format] ASCII ESC \ nl nh Hex 1B 5C nl nh Decimal nl nh [Range] 0 nl nh 255 [Description] unit] [Reference] Sets the lateral relative position based on the current position by using the Horizontal or vertical motion unit This command sets the distance from the current position to n[(nl+nh 256)horizontal motion unit] Any setting that exceeds the printable area is ignored. When printing position moves to the right:nl+nh 256=N. When printing position moves to the left,using radix complement:nl+nh 256= N. The print starting position moves from the current position to[n horizontal motion Vertical and horizontal motion units are set by GSP command. Horizontal motion units are used under standard mode. Under page mode, selecting to use horizontal or vertical motion units according to the direction of printing area and zero position. The system of selection is as below: ESC $, GS P 1 Using horizontal shifting when the beginning position is the top left or lower right corner of the printing area which is set by ESC T; 2Using vertical shifting when the beginning position is the lower left or top right corner of the printing area which is set by ESC T ESC a n Selecting alignment mode [Format] ASCII ESC a n Hex 1B 61 n Decimal n [Range] 0 n 2, 48 n 50 [Description] Making all the printing datas array in appointed alignment

25 [Default value] n = 0 [Example] Relationship between value of n and alignment are as below: n Alignment 0,48 Align left 1, 49 Align center 2, 50 Align right This command is just available at the zero position of the line and under Standard mode. This command just changes the internal mark position under page mode. This command revises the blank area according to HT,ESC$ or ESC\. ESC c 5 n Permiting/Forbiding key stoke [Format] ASCII ESC c 5 n Hex 1B n Decimal n [Range] 0 n 255 [Description] Permiting/Forbiding key stoke. When the lowest bit of n is 0,keystoke works When the lowest bit of n is1,keystoke is forbidden. Only the lowest bit of n is effective. When the key stoke is forbidden, it does not work When carrying out the macro command, key stoke works all the time, but can not feed paper by it [Default value] n = 0 ESC d n Printing and feeding paper forward for n lines [Format] ASCII ESC d n [Range] 0 n 255 Hex 1B 64 n Decimal n [Description] Printing the datas in print buffer and feeding paper forward for n lines(character row) This command sets the loading position at the beginning of the row

26 This command does not influence the line space which is set by ESC 2 or ESC 3 The maximum distance of feeding paper is 1016mm.If it is beyond this distance, taking the maximum distance. [Reference] ESC 2, ESC 3 ESC t n Selecting character code table [Format] ASCII ESC t n Hex 1B 74 n Decimal n [Range] 0 n 255 [Description] Selecting code page n from character code table. Selection of n are as below: N 代码页 Code Page 0 CP437 [ 美国, 欧洲标准 ] CP437 [U.S.A., Standard Europe] 1 KataKana [ 片假名 ] Katakana 2 PC850 [ 多语言 ] PC850 [Multilingual] 3 PC860 [ 葡萄牙 ] PC860 [Portuguese] 4 PC863 [ 加拿大 - 法语 ] PC863 [Canadian-French] 5 PC865 [ 北欧 ] PC865 [Nordic] 6 WCP1251 [ 斯拉夫语 ] WCP1251 [Cyrillic] 7 CP866 斯拉夫 2 CP866 Cyrilliec #2 8 MIK[ 斯拉夫 / 保加利亚 ] MIK[Cyrillic /Bulgarian] 9 CP755 [ 东欧, 拉脱维亚 2] CP755 [East Europe,Latvian 2] 10 [ 伊朗, 波斯 ] Iran 11 保留 reserve 12 保留 reserve 13 保留 reserve 14 保留 reserve 15 CP862 [ 希伯来 ] CP862 [Hebrew] 16 WCP1252 [ 拉丁语 1] WCP1252 Latin I 17 WCP1253 [ 希腊 ] WCP1253 [Greek] 18 CP852 [ 拉丁语 2] CP852 [Latina 2] 19 CP858 [ 多种语言拉丁语 1+ 欧元符 ] 20 伊朗 Ⅱ [ 波斯语 ] CP858 Multilingual Latin Ⅰ +Euro) Iran II 21 拉脱维亚 Latvian 22 CP864 [ 阿拉伯语 ] CP864 [Arabic] 23 ISO [ 西欧 ] ISO [West Europe] 24 CP737 [ 希腊 ] CP737 [Greek] 25 WCP1257 [ 波罗的海 ] WCP1257 [Baltic] 26 [ 泰文 1] Thai 1 27 CP720[ 阿拉伯语 ] CP720[Arabic] 28 CP855 CP855

27 29 CP857[ 土耳其语 ] CP857[Turkish] 30 WCP1250[ 中欧 ] WCP1250[Central Europe] 31 CP775 CP WCP1254[ 土耳其语 ] WCP1254[Turkish] 33 WCP1255[ 希伯来语 ] WCP1255[Hebrew] 34 WCP1256[ 阿拉伯语 ] WCP1256[Arabic] 35 WCP1258[ 越南语 ] WCP1258[Vietnam] 36 ISO [ 拉丁语 2] ISO [Latin 2] 37 ISO [ 拉丁语 3] ISO [Latin 3] 38 ISO [ 波罗的语 ] ISO [Baltic] 39 ISO [ 斯拉夫语 ] ISO [Cyrillic] 40 ISO [ 阿拉伯语 ] ISO [Arabic] 41 ISO [ 希腊语 ] ISO [Greek] 42 ISO [ 希伯来语 ] ISO [Hebrew] 43 ISO [ 土耳其语 ] ISO [Turkish] 44 ISO [ 拉丁语 9] ISO [Latin 3] 45 [ 泰文 2] Thai2 46 CP856 CP856 [Default value] n = 0 [Reference] ESC { n Selecting/canceling invert printing mode [Format] ASCII ESC { n [Range] 0 n 255 [Description] degree. [Default value] n = 0 [Example] Hex 1B 7B n Decimal n Selecting/canceling invert printing mode When the lowest bit of n is 0,canceling invert printing mode When the lowest bit of n is1,selecting invert printing mode. Only the lowest bit of n is effective. The command is just effective on the beginning of the line under standard mode. The command just changes internal marker bit under page mode. The command has no effect on the printing of page mode. Under invert printing mode, the printer will whirl the line of being printed for 180

28 FS P n Printing the prestored bit map [Format] ASCII FS P n [Range] 0 n 7 [Description] Hex 1C 50 n Decimal n This command prints the 2 value bit map which is prestored in the printer and not easily lost. The bit map in memory which is not easily lost can be produced and written by the tool in PC. The max width is 576dots,and max height is 910 dots. N is the destination bit map code. Before the destination bit map code has not been defined,this command is not available.. The bit map must be the 2 value bit map. This command will not be influenced by printing mode.(bold overlap underline character dimension or inverse print).. If the width of being printed beyond one line, the out profile will not be printed..it needs special purpose tools to print the downloaded bit map, Please see (T9 set tool software).the bit map by this mode does not lose unless download other bitmap to cover it. GS! n Selecting character boundary [Format] ASCII GS! n Hex 1D 21 n Decimal n [Range] 0 n 255 (1 longitudinal magnification multiple 8,1 lateral magnification multiple 8) [Description] Using 0 to 2 bits to select character height,4 to7 bits to select character width As follows: Bit 0/1 Hex Decimal Function 0-3 Selecting character width, see table1 4-7 Selecting character height, see table2

29 Table 1 Table 2 Selecting character height Hex Decimal longitudinal magnification Selecting character width Hex Decimal lateral magnification; (normal) (normal) (double width) (double height [Default value] n = 0 [Reference] ESC! This command is effective to all the characters(ascii and Chinese characters) except HRI characters If n is out of the range, this command will be neglected. Under standard mode, portrait is the direction of feeding paper, landscape is perpendicular to the direction of feeding paper. But when the character rotates 90 degree clockwise, portrait and landscape are reversed Portrait and landscape under page mode depend on the direction of the area. All the character are aligned baseline when the character of the same line enlarge different times Selecting/canceling the double width and double height of the character can also be set by ESC! command. However, the setting of the last received command is effective. GS * x y d1...d(x y 8) Defining downloaded bit map [Format] ASCII GS * x y d1...dk Hex 1D 2A x y d1...dk Decimal x y d1...dk [Range] 1 x 255, 1 y 48 x y d 255 k=x y 8 [Description] Use appointed bit number by x and y to define the downloaded bit map x is the dot number of horizontal y is the dot number of vertical d is data of specified bit map x*8 is the dot number of horizontal.;y*8 is the dot number of vertical. If x*y is off limit, then the command is forbidden.

30 d means the image data.1print,0 not print In the following circumstances, clear the definition of downloaded bit image.: 1 carry out ESC@ command 2 Power off or reset Relationship between print data and download bit map is as below: [Reference] GS / GS / m Printing downloaded bi t map [Format] ASCII GS / m Hex 1D 2F m Decimal m [Range] 0 m 3, 48 m 51 [Description] Printing mode is appointed by m when print a bit map m printing mode selections are as below: m mode vertical (DPI) horizontal (DPI) 0, 48 normal , 49 Double width , 50 Double height , 51 Double width and height This command will be ignored if the downloaded bit map is not defined. The command is effective only when there is no data in the printing buffer under standard mode Except inversion mode, other modes have no effect on it(include bold double print underline enlarge font and invert printing, etc. The out profile will not be printed if the bit map out of the range.. This command prints the bit map downloaded in RAM but not Flash. [Reference] GS *

31 GS B n Selecting/canceling black white revert printing mode [Format] ASCII GS B n [Range] 0 n 255 [Description] Hex 1D 42 n Decimal n Selecting/canceling black white revert printing mode When the lowest bit of n is 0,canceling black white reverse printing mode. When the lowest bit of n is1,selecting black white reverse printing mode. Only the lowest bit of n is effective This command is available to all the characters (except HRI characters) After selecting black white reverse printing, the space between characters which is set by ESC SP command is also reversing. This command does not influence bit map, user defined bit map, barcode, HRI character and blank space which is set by HT,ESC $ and ESC\ This command does not influence the blank space between lines. Priority of black white reverse printing mode is higher than it of underline mode. When selecting black white reverse printing mode, underline mode is not effective. It will be effective after canceling black white reverse printing mode. [Default value] n = 0 GS H n Selecting the printing position of HRI character [Format] ASCII GS H n Hex 1D 48 n Decimal n [Range] 0 n 3, 48 n 51 [Description] When printing the barcode, selecting the printing position for HRI character N appoints the printing position of HRI n Printing position 0, 48 No printing 1, 49 Above the barcode 2, 50 Below the barcode 3, 51 Both above and below the barcode HRI is the character of content note of barcode The style of HRI character is appointed by GS f. [Default value] n = 0 [Reference] GS f, GS k GS L nl nh Setting left margin

32 [Format] ASCII GS L nl nh Hex 1D 4C nl nh Decimal nl nh [Range] 0 nl nh 255 [Description] Setting left margin by nl and nh Setting left margin at[(nl+nh 256) horizontal motion unit)]inches. This command is just available at the zero position of the line and under standard It is not available under page mode, the printer will handle it as normal data This command does not influence the printing under page mode Taking the Max width is it goes beyond the max printing width Vertical and horizontal motion units are set by GSP. Changing the motion will not influence the current left margin. [Default value] nl = 0, nh = 0 [Reference] GS P x y GS P, GS W Setting horizontal and vertical motion units [Format] ASCII GS P x y [Range] 0 x 255 [Description] Hex 1D 50 x y Decimal x y 0 y 255 Setting horizontal motion units as near 25.4/xmm( 1/x inch)setting vertical Motion units as near 25.4/ymm(1/y inch) When x and y are all 0, x and y are setting as default value Direction is perpendicular to the feeding is horizontal, the feeding direction is vertical Under standard mode, making the character whirl by x or y(does not change if invert or clockwise rotates 90API) 1Using x command: 2 ESC SP, ESC $, ESC \, GS L, GS W Using y command: ESC 3, ESC J, GS V Under page mode, according to the direction of printing and the starting position to use x or y 1 When the starting position is set as top left corner or lower right by ESC T: Using x command: ESC SP, ESC $, ESC W, ESC \ Using y command: ESC 3, ESC J, ESC W, GS $, GS \, GS V 2When the starting position is set as top right corner or lower left by ESC T:

33 Using x command: ESC 3, ESC J, ESC W, GS $, GS \ Using y command: ESC SP, ESC $, ESC W, ESC \, GS V [Default value] This command does not influence other settings set before The minimum motion distance is the result of combined action of this and other commands.a inch=25.4mm x=203,y=203,now a motion unit is a printing dot. Horizontal motion distance is 1/8mm,and vertical motion distance is 1/8mm. [Reference] ESC SP, ESC $, ESC 3, ESC J, ESC W, ESC \, GS $, GS L, GS V, GS W, GS \ 1GS V m 2 GS V m n [Format] Select cutting mode and cut paper [Range] 1 m = 0,48,1, 49 [Description] 1 ASCII GS V m Hex 1D 56 m Decimal m 2 ASCII GS V m n Hex 1D 56 m n Decimal m n 2 m = 66, 0 n 255 Select one cutting mode and cut paper. Select cutting mode according to the value of m,as follows: m cutting mode 0,1,48,49 half cutting 66 Feed paper(cutting position+[n*(vertical shifting unit)inch])and half cutting paper. [Note 1and 2 ] This command does effect only at the beginning of line. [Note 2 ] m = 0,48,1, 49, The printer cuts directly. GS W nl nh When m=66,the printer feed paper[the distance from printing position to cut +n*(vertical motion unit)] then cut paper. The lateral and vertical shifting unit are set by the command GS P. The number of feeding paper is computed by vertical motion unit Setting the width of printing area [Format] ASCII GS W nl nh [Range] 0 nl 255 [Description] Hex 1D 57 nl nh Decimal nl nh 0 nh 255 Setting the width of printing area by nl and nh

34 Setting width of printing area to [( nl + nh 256) horizontal motion unit)] inches. This command is just available at the zero position of the line and under standard mode. It is not available under page mode, the printer will handle it as normal data This command does not influence the printing under page mode. If [left margin+width of printing area]goes beyond the print able area, the width of printing is it of[printable area width left margin] Vertical and horizontal motion units are set by GSP. Changing them will not Influence the current left margin and area width Using horizontal motion units to count the width of printing area [Default value] nl = 64, nh = 2 [Reference] GS f n GS L, GS P Selecting font of HRI used [Format] ASCII GS f n Hex 1D 66 n Decimal n [Range] n = 0, 1, 48, 49 [Description] [Default value] n = 0 [Reference] GS h n When printing barcode, selecting a style for HRI character Selecting style by n is as below: n Style 0,48 Standard ASCII character(12 24) 1,49 Compressed ASCII character(9 17) HRI character is the note of barcode content HRI character printing position is set by GSH command GS H, GS k Selecting height of barcode [Format] ASCII GS h n [Range] 1 n 255 Hex 1D 68 n Decimal n [Description] Selecting height of barcode The height of barcode is n dots

35 [Default value] n = 162 [Reference] GS k 1GS k m d1...dk NUL2 GS k m n d1...dn [Format] Printing barcode [Range] 1 0 m 6 [Description] 1 ASCII GS k m d1...d k NUL Hex 1D 6B m d1...d k 00 Decimal m d1...d k 0 2 ASCII GS k m n d1... dn Hex 1D 6B m n d1... dn Decimal m n d1... dn (Value range of k and d is decided by its type) 265 m 73 (Value range of k and d is decided by its type) Selecting a kind of barcode and printing m is used to select type of barcode, as follows: m Barcode type Number of d character 1 0 UPC-A 11 k d 57 1 UPC-E 11 k d 57 2 JAN13 (EAN13) 12 k d 57 3 JAN 8 (EAN8) 7 k 8 48 d 57 4 CODE39 1 k d 57, 65 d 90, 32, 36, 37,43 5 ITF 1 k d 57 6 CODABAR 1 k d 57, 65 d 68, 36, 43, 45,46,47, UPC-A 11 n d UPC-E 11 n d JAN13 (EAN13) 12 n d JAN 8 (EAN8) 7 n 8 48 d CODE39 1 n d 57, 65 d 90, 32, 36, 37,43 d1 = d k = ITF 1 n d CODABAR 1 n d d 68, 36, 43,45,46, CODE93 1 n d CODE128 2 n d 127 [Note 1 ] This command is ended by NULL under this format When selecting code of UPC-A or UPC-E, after receiving 12 bytes data, printer will handle the rest as normal character When selecting type of JAN13(EAN13),after receiving13 bytes data, printer will

36 [Note 2 ] handle the rest as normal character When selecting type of JAN8(EAN8),after receiving 8 bytes data, printer will handle the rest as normal character Number of ITF code data must be aeven number. If entering code data of odd number, the last data will be ignored N is used to appoint the number of pointing barcode data. The printer will handle then byte data follow as barcode data If n goes beyond the specified range, the printer will not handle this command, and handle the data following as normal data [Note(Standard mode)] If the barcode d goes beyond the specified range, this command is invalid. If the cross wise of barcode goes beyond printing area, invalid No matter what is the height set by ESC 2 or ESC 3,the distance of feeding paper is the This command only available when there is no data in printing buffer, if not, the command will be ignored. same as the height of barcode. The printing position will be set at the beginning of the line after printing the barcode. Other mode setting(bold double printing underline character dimension inverse and character clockwise rotates 90 degree)can not influence this command except Inversion mode [Note(page mode)] This command just produces the barcode figure in printing buffer, but not print. Moving the printing position to the right of the barcode after handling the barcode data. If the d goes beyond the specified range, this command will be ignored. If the width of the barcode goes beyond the printing area, this command will be ignored Referring appendix A, related information of CODE128 and character set When using CODE128,encoding according to the description following 1 Selecting character set before barcode data(code A CODE B or CODE C) 2 Selecting character set according to sending character { and combine with another character; ASCII character { is finished by sending character { for twice. Appointing Sending data Character ASCII Hex Decimal SHIFT {S 7B, ,83 CODE A {A 7B, , 65 CODE B {B 7B, , 66 CODE C {C 7B, , 67 FNC1 {1 7B, , 49 FNC2 {2 7B, , 50 FNC3 {3 7B, , 51

37 [Example] FNC4 {4 7B, , 52 "{" {{ 7B, 7B 123, 123 Printing No Using CODE B to print No.,and then using CODE C to print the digital rest GS k GS k If it is not character set selection at the beginning of barcode data, the printer will stop handling this command, and handling the rest data as normal data If { and the character close behind is not the combination as above, the printer will stop handling this command,and handling the rest data as normal data. If the character is not the data of barcode character set, the printer will stop handling this command, and handling the rest data as normal data. When printing HRI character, not printing shift character and character set selection data HRI character of function character is not printed HRI character of control character(<00>h to<1f>hand<7f>h)is not printed <Others> Ensure the left and right space of barcode. Space is different because of different barcode style. [Reference] GS H, GS f, GS h, GS w, appendix A GS w n Setting the width of barcode [Format] ASCII GS w n [Range] 2 n 6 [Description] n Hex 1D 77 n Decimal n Setting width of barcode horizontal module Appointing the barcode horizontal module by n Mono basis module width (mm) Double basic module width Narrow-based module (mm) Wide-based module (mm)

38 Barcode of mono basis module is as below: UPC-A, UPC-E, JAN13 (EAN13), JAN8 (EAN8), CODE93, CODE128 Barcode of biradical module is as below: CODE39, ITF, CODABAR [Default value] n = 2 [Reference] GS k The Chinese characters controlling commands FS! n Setting Chinese characters mode [Format] ASCII FS! n Hex 1C 21 n Decimal n [Range] 0 n 255 [Description] Using value of n to set the printing mode of Chinese characters Bit 0/1 Hex Decimal Function 0, 1 Undefined Canceling double width Selecting double width Canceling double height Selecting double height 4-6 Undefined Canceling underline Selecting underline When double width and double height are set together, portrait and landscape will been enlarged two times together(including left and right space). Printer can add underline to all the characters, including left and right space. But can not add underline to the space caused by HT command (horizontal tab),either the 90 degree clockwise characters. The width of underline is set by FS-has no relation to the character boundary When the height of the character in one line is not the same, all the characters align the base line Using FS W and GS!can make the characters bold, the setting of the last received command is effective. Also can use FS to select or cancel the underline, the setting of the last received command is effective. [Default value] n = 0 [Reference] FS -, FS W,GS! FS & Selecting Chinese character mode [Format] ASCII FS &

39 [Description] [Reference] Hex 1C 26 Decimal Selecting Chinese character mode When select Chinese character mode, printer will judge whether the character is Hanzi interal code, if it is, dealing with the first byte in advance. Then the second one. After powering up, the printer will select Chinese character mode by itself. FS., FS C FS - n selecting/canceling Chinese underline mode [Format] ASCII FS - n Hex 1C 2D n Decimal n [Range] 0 n 2, 48 n 50 [Description] selecting or canceling Chinese underline according to value of n n Function 0, 48 canceling Chinese underline 1, 49 selecting Chinese underline(1dot width) 2, 50 selecting Chinese underline(2dots width) Printer can add underline to all the characters, including left and right space. But can not add underline to the space caused by HT command(horizontal tab),either the 90 degree clockwise characters. It does not carry out the underline printing after canceling underline mode,but the previous set does not change.the default underline width is 1dot. The underline width does not change even if changing the character dimension. Can use FS! to select or cancel the underline, the setting of the last received command is effective [Default value] n = 0 [Reference] FS! FS. canceling chinese mode [Format] ASCII FS. Hex 1C 2E Decimal [Description] canceling chinese mode When the Chinese mode is canceled, all the characters are the same as ASCII style, and deal with one byte once..selecting Chinese mode when power on. [Reference] FS &, FS C

40 FS 2 c1 c2 d1...dk Defining user self-defined Chinese [Format] ASCII FS 2 c1 c2 d1...dk Hex 1C 32 c1 c2 d1...dk Decimal c1 c2 d1...dk [Range] c1,c2 represent the code of defined characters. c1 = FEH A1H c2 FEH 0 d 255 k = 72 [Description] Defining the Chinese specified by c1,c2. C1,c2 represent user self-defined Chinese code,c1 specifies the first byte,c2 specifies the second byte. D represent data.every bit of byte is 1 represents to print the dot,0 means does not print. It can define 10 chinese the most. [Default value] no self-defined Chinese The relation between self-defined Chinese font and data as follows:

41 FS C n selecting Chinese code system [Format] ASCII FS C n1 n2 Hex 1C 43 n1 n2 Decimal n1 n2 [Range] n=0,1,48,49 [Description] selecting Chinese code system n selecting Chinese code system 0, 48 Simplified Chinese(GB2312 或 GB18030) 1, 49 Traditional Chinese-TC(BIG5) The command does not change the parameter set of flash It returns to default after carried out command power off or reset. [Default value] n = 0 Simplified Chinese model. n = 1 Traditional Chinese-TC model FS S n1 n2 Setting the left and right space of Chinese character [Format] ASCII FS S n1 n2 Hex 1C 53 n1 n2 Decimal n1 n2 [Range] 0 n n2 255 [Description] Setting the space of left and right are n1,n2. When the printer have GSP command, the left space is[n1*lateral or vertical motion unit] inch, the right space is[n2*lateral or vertical motion unit]inch.

42 The left and right space will be doubled after setting the double width mode. The shifting unit is set by the command GS P. The former character space does not change even if the lateral and vertical units are changed. Using the lateral shifting unit under the standard mode. Selecting to use the lateral or vertical shifting unit according to the printing area under page mode. 1 Using horizontal shifting when the beginning position is the top left or lower right corner of the printing area 2 Using vertical shifting when the beginning position is the lower left or top right corner of the printing area The maximum distance of Chinese is36mm.if it is beyond this distance, taking the maximum distance. [Default] n1 = 0, n2 = 0 [Reference] GS P FS W n Selecting/canceling Chinese double height or width [Format] ASCII FS W n Hex 1C 57 n Decimal n [Range] 0 n 255 [Default] Selecting/canceling Chinese double width mode Cancel chinese double width mode when the lowest bit is 0 Select Chinese double width mode when the lowest bit is 1. only the lowest bit of n is effective. To print chinese dimension under double width mode is the same as to select both double width and double height. The Chinese dimension is printed normally after cancelling the Chinese double width mode. When the height of the character in one line is not the same, all the characters align the baseline Also using FS! or GS!can select or cancel Chinese double height and width mode, the setting of the last received command is effective. [Default] n = 0 [Reference] FS!, GS!