Microsoft Word - FM-3528UGK-520D.doc

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Microsoft Word - FM-3528UGK-520D.doc"

Transcription

1 佛山市国星光电股份有限公司 FOSHAN NATIONSTAR OPTOELECTRONICS CO., LTD 产品规格书 SPECIFICATION 顾客名称 Customer 顾客部品号 Customer No. 产品名称 Product 产品型号 Type TOP LED FM-358UGK-5D 顾客确认 APPROVED SIGNATURES 地址 : 广东省佛山市禅城区华宝南路 8 号 Add: NO.8 South Huabao Rd,Foshan,Guangdong,China 电话 (Tel): , , 传真 (Fax): ,83 邮编 (Zip):58 批准 APPROVE 研究开发中心 Research & Development Center 审核 CHECK 制定 DRAW 版本号 (Version NO):A 首次发放日期 (Release Date):-5-4

2 FM-358UGK-5D TOP Light Emitting Diode 技术数据表 Technical Data Sheet 本产品主要作为信号指示及照明的电子元件广泛应用于各类使用表面贴装结构的电子产品中 本产品也广泛用于各类室内外的装饰照明 This product is generally used as indicator and luminary for electronic equipment. And it also be widely used for indoor and outdoor decorative lighting. 特性 : Features: 管芯材料 : InGaN Material: 封装材料 : 环氧树脂 Encapsulation: Resin 发光颜色 : 绿色 Emitting Color: Green 焊接方法 : 无铅回流焊 Soldering methods: Pb-Free reflow soldering 光强高, 功耗低, 可靠性好, 寿命长 High Luminous Intensity,Low Power Dissipation,good Reliability and Long Life 符合欧盟公布的 ROHS 指令要求 Complied With ROHS Directive 目录 Catalogue 电性参数 Electrical Characteristics... 典型特性曲线 Typical Characteristic Curves...3 可靠性实验 Reliability Test Items And Conditions...4 外形尺寸 Outline Dimensions...5 包装 Packaging...6 焊接指导 Guideline for Soldering...8 使用注意事项 Precautions...9 * 产品规格如因工艺改进而有所改变, 恕不另行通知 *The Specifications of the product may be modified for improvement without notice.

3 电性参数 Electrical Characteristics 极限参数 ( 温度 =5 ): Absolute Maximum Ratings (Temperature=5 C): 参数名称 Parameter 符号 Symbol 数值 Rating 单位 Unit 正向电流 Forward Current I F 5 ma * 正向脉冲电流 Pulse Forward Current * I FP ma 反向电压 Reverse Voltage 工作温度 Operating Temperature 贮存温度 Storage Temperature 功耗 Power Dissipation V R 5 V T OPR -3 ~ +85 Tstg -4 ~ + P D 9 mw 光电参数 ( 温度 =5 ): Electro-Optical Characteristics (Temperature=5 C): * 注 : 脉冲宽度.ms, 占空比 / * Note: Pulse width.ms, Duty / 参数名称 Parameter 反向电流 Reverse Current 正向电压 Forward Voltage 峰值波长 Peak Wavelength 主波长 Dominant Wavelength 半波宽度 Spectrum Radiation Bandwidth 光强 Luminous Intensity 视角度 View Angle 符号 Symbol 条件 Condition 最小值 Min. 典型值 Typ. 最大值 Max. 单位 Unit I R V R =5V 5 μa V F V λ P 55 nm λ D I F =ma nm Δλ 35 nm I V mcd θ/ deg.

4 典型特性曲线 Typical Characteristics Curves 正向电流 ( Forward Current )( ma ) 伏安特性 Volt - Ampere Characteristics TAmbient= 相对光强与正向电流特性 Relative Luminous Intensity VS Forward Current 正向电压 ( F orward Voltage )( V) 正向电流 ( Forward Current )( ma ) 相对光强 ( Relative Luminous Intensity ).. TAmbient= 5 4 正向电流 ( Forward Current ) ( ma ) 正向电流降额曲线 Forward Current Derating Curve 环境温度 ( Ambient Temperature)( ) 相对光强 ( Relative Luminous Intensity ) 光强与环境温度曲线 Luminous Intensity VS Ambient Temperature 环境温度 ( Ambient Temperature)( ) 相对光强 ( Rel ative Luminous Intensity )(%) 光谱分布特性曲线 Relative Spectral Distribution 波长 ( Wavelength )( nm ) 75 相对光强 ( R elative Luminous Intensity )(%) 光强分布特性曲线 Typical Spatial Distribution 角度 ( Angle)( Deg.)

5 可靠性试验 Reliability Test Items And Conditions 试验项目 Test Items 可焊性试验 Solderability 温度快速变化继之以循环湿热 Thermal Shock Followed by High Temperature And High Humidity Cyclic 耐焊接热试验 Resistance For Soldering Heat 电耐久性试验 DC Operating Life 高温贮存试验 High Temperature Storage 试验条件 Test Conditions 焊接温度 (Solder Temperature):3 焊接时间 (Solder Duration):(3.5±.5)sec. -4 min. 5 次循环转移 (~3) min. 5 Cycles Shift min. 5 ~55 (9%~95%)RH 次循环 48 hrs., 恢复 hrs. Cycles for 48 hrs. Recover for hrs. 红外回流焊法 Reflow Soldering hrs. 正向电流 :5mA Forward Current:5mA 试验数量 Quantity 5 判断标准 Judging Criteria 湿润良好上锡面积在 95% 以上 Solderable Area Over 95% C= & II 5 C= & II C= & I hrs. 5 C= & I 循环湿热 High Temperature And High Humidity Cyclic 5 ~55 (9%~95%)RH 6 次循环 44 hrs., 恢复 hrs. 6 Cycles for 44 hrs. Recover for hrs. C= & I 失效判断标准 Criteria For Judging Damage 测试项目 Items 正向电压 Forward Voltage 反向电流 Reverse Current 光强 Luminous Intensity 符号 Symbol 测试条件 Test Conditions 失效判断标准 I Criteria For Judging Damage I 失效判断标准 II Criteria For Judging Damage II V F I F =ma USL*. USL I R V R =5V USL. USL I V I F =ma LSL**.5 LSL * USL: 标准值上限值,**LSL: 标准值下限值 * USL: Upper Standard Level, **LSL: Lower Standard Level 4

6 外形尺寸 Outline Dimension 推荐焊盘 Recommended Soldering Pad 极性 Polarity Note: A: 缺口标志 A:Nick Mark 单位 :mm, 未注公差 :±. mm All dimensions in mm. Tolerances unless mentioned is ±. mm. 5

7 LED PRODUCTS IF = x ma TYPE: XX-XXXXX-XX λd: (xxx-xxx) nm QTY: XXXX IV: (xxx-xxx) mcd BIN: XX VF: (xx-xx) V QC LOT: QC: PASS FOSHAN NATIONSTAR OPTOELECTRONICS CO., LTD 佛山市国星光电股份有限公司 包装 () Packaging () 载带 Carrier Tape 编带细节 Details Of Carrier Tape 单位 :mm, 未注公差 :±. mm All dimensions in mm, tolerances unless mentioned is ±. mm. 前进方向 Progressive Direction A: 盖带,3 mm;b: 引导, 空带,mm;C: 编载产品 只 ;D: 尾部, 空带,mm A: Top Cover Tape, 3mm; B: Leader, Empty, mm; C: Lamps Loaded; D: Trailer, Empty, mm. 带盘 Reel Dimension 前进方向 Progressive Direction xxxx 标签 Label 6

8 LED PRODUCTS IF = x ma TYPE: XX-XXXXX-XX λd: (xxx-xxx) nm QTY: XXXX IV: (xxx-xxx) mcd BIN: XX VF: (xx-xx) V QC LOT: QC: PASS xxxx FOSHAN NATIONSTAR OPTOELECTRONICS CO., LTD 佛山市国星光电股份有限公司 包装 () Packaging () 防潮抗静电包装 Moisture Proof and Anti-Electrostatic Foil Bag 标签 Label 防潮抗静电包装袋 Moisture Proof and Anti-Electrostatic Foil Bag 干燥剂 Moisture Absorbent Material 密封 Sealed 标签 Label 外包装箱 Cardboard Box 佛山市国星光电股份有限公司 FOSHAN NATIONSTAR OPTOELECTRONICS CO.,LTD 地址 : 佛山市禅城区华宝南路 8 号邮编 :58 TEL:(86-757)83988 FAX:(86-757)86 标签说明 Label Explanation TYPE: 产品型号 QTY: 数量 Quantity BIN: 分档 Rank LOT: 批号 Lot Number λd: 波长范围 Wavelength Range IV: 光强范围 Luminous Intensity Range VF: 正向电压范围 Forward Voltage Range IF: 以上数据测试电流 Testing Current TOP LED TYPE: XX-XXXXX-XX QTY: XXXX BIN: LOT: XX xxxx λd: (xxx-xxx) nm IV: (xxx-xxx) mcd VF: QC: (xx-xx) V QC PASS IF = x ma FOSHAN NATIONSTAR OPTOELECTRONICS CO., LTD 佛山市国星光电股份有限公司 7

9 焊接指导 () Guideline for Soldering (). 使用烙铁人手焊接 Hand Soldering 推荐使用功率低于 W 的烙铁, 焊接时烙铁的温度必须保持在 36 以下, 且每个电极只能进行一次焊 接, 每次焊接的持续时间不得超过 3 秒 人手焊接过程中的不慎操作易引起 LED 产品的损坏, 应当小心谨慎 A soldering iron of less than W is recommended to be used in Hand Soldering. Please keep the temperature of the soldering iron under 36 while soldering. Each terminal of the LED is to go for less than 3 second and for one time only. Be careful because the damage of the product is often started at the time of the hand soldering.. 回流焊接 : 推荐使用以下无铅回流焊接温度图进行 Reflow Soldering: Use the conditions shown in the under Figure of Pb-Free Reflow Soldering. 推荐温度焊接曲线 Recommended Solder Profile 温度 ( Temperature )( ) 升温 - Ramp up 预热 Preheat ( 6-8) sec. sec. Max. ( 6-5) sec. 降温 - Ramp down 45 ± 5 回流焊接最多只能进行两次 时间 ( Time) Reflow soldering should not be done more than two times. 在回流焊接升温过程中, 请不要对 LED 施加任何压力 Stress on the LEDs should be avoided during heating in soldering process. 在焊接完成后, 待产品温度下降到室温之后, 再进行其他处理 After soldering, do not deal with the product before its temperature drop down to room temperature. 8

10 焊接指导 () Guideline for Soldering () 3. 清洗 : Cleaning 在焊接后推荐使用酒精进行清洗, 在温度不高于 3 的条件下持续 3 分钟, 不高于 5 的条件下持续 3 秒 使用其他类似溶剂清洗前, 请先确认使用的溶剂不会对 LED 的封装和环氧树脂部分造成损伤 超声波清洗也是有效的方法, 一般最大功率不应超过 3W, 否则可能对 LED 造成损伤 请根据具体的情况预先测试清洗条件是否会对 LED 造成损伤 It is recommended that alcohol be used as a solvent for cleaning after soldering. Cleaning is to go under 3 for 3 minutes or 5 for 3 seconds. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Ultrasonic cleaning is also an effective way for cleaning. But the influence of Ultrasonic cleaning on LED depends on factors such as ultrasonic power. Generally, the ultrasonic power should not be higher than 3W. Before cleaning, a pre-test should be done to confirm whether any damage to LEDs will occur. * 注意 : 此一般指导原则并不适用于所有 PCB 设计和焊接设备的配置 具体工艺受到诸多因素的影响, 请根据特定的 PCB 设计和焊接设备来确定焊接方案 * Note: This general guideline may not apply to all PCB designs and configurations of all soldering equipment. The technique in practice is influenced by many factors it should be specialized base on the PCB designs and configurations of the soldering equipment. 9

11 使用注意事项 () Precautions (). 贮存 : Storage 本产品使用密封防潮抗静电袋包装, 并附有干燥剂, 未开封的产品有一年的保存时间 Moisture proof and anti-electrostatic package with moisture absorbent material is used, to keep moisture to a minimum. 开封前, 产品须存放在温度不高于 3, 湿度不高于 6%RH 的环境中 Before opening the package, the product should be kept at 3 or less and humidity less than 6% RH, and be used within a year. 开封后, 产品须存放在温度不高于 3, 湿度不高于 %RH 的环境中, 且应该在 4 小时 ( 天 ) 内使用完 建议工作环境为温度不高于 3, 湿度不高于 6%RH After opening the package, the product should be stored at 3 or less and humidity less than %RH, and be soldered within 4 hours ( day). It is recommended that the product be operated at the workshop condition of 3 or less and humidity less than 6%RH. 对于尚未焊接的 LED, 如果吸湿剂或包装失效, 或者产品没有符合以上有效存储条件, 烘焙可以起到一定的性能恢复效果 烘焙条件 :(8±5), 持续 4 小时 If the moisture absorbent material has fade away or the LEDs have exceeded the storage time, baking treatment should be performed based on the following condition: (8±5) for 4 hours.. 静电 : Static Electricity 静电和电涌会导致产品特性发生改变, 例如正向电压降低等, 如果情况严重甚至会损毁产品 所以在使用时必须采取有效的防静电措施 所有相关的设备和机器都应该正确接地, 同时必须采取其他防止静电和电涌的措施 使用防静电手环, 防静电垫子, 防静电工作服 工作鞋 手套, 防静电容器, 都是有效的防止静电和电涌的措施 Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. even not light. All devices, equipment and machinery must be properly grounded. At the same time, it is recommended that wrist bands or anti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

12 使用注意事项 () Precautions () 3. 设计建议 : Design Consideration 设计电路时, 通过 LED 的电流不能超过规定的最大值, 同时, 还需使用保护电阻, 否则, 微小的电压变化将会引起较大的电流变化, 可能导致产品损毁 建议使用以下 (A) 电路, 该电路能够很好的调节通过每个 LED 的电流 ; 不推荐使用 (B) 电路, 该电路在持续的电压驱动下,LED 的正向电压 (VF) 发生变化, 电流会随之而发生变化, 可能使某些 LED 承受高于规定的电流值 In designing a circuit, the current through each LED must not exceed the absolute maximum rating specified for each LED. In the meanwhile, resistors for protection should be applied, otherwise slight voltage shift will cause big current change, burn out may happen. It is recommended to use Circuit A which regulates the current flowing through each LED rather than Circuit B. When driving LEDs with a constant voltage in Circuit B, the current through the LEDs may vary due to the variation in Forward Voltage (VF) of the LEDs. In the worst case, some LED may be subjected to stresses in excess of the Absolute Maximum Rating. (A) (B) LED 的特性容易因为自身的发热和环境的温度的改变而发生改变 温度的升高会降低 LED 的发光效率 影响发光颜色等, 所以在设计时应充分考虑散热的问题 Thermal Design is paramount importance because heat generation may result in the Characteristics decline, such as brightness decreased, Color changed and so on. Please consider the heat generation of the LEDs when making the system design.

13 使用注意事项 (3) Precautions (3) 4. 其他事项 : Others 直接用手拿取产品不但会污染封装树脂表面, 也可能由于静电等因素导致产品性能的改变 过度的压力也可能直接影响封装内部的管芯和金线, 因此请勿对产品施加过度压力, 特别当产品处于高温状态下, 例如在回流焊接过程中 When handling the product, touching the encapsulant with bare hands will not only contaminate its surface, but also affect on its optical characteristics. Excessive force to the encapsulant might result in catastrophic failure of the LEDs due to die breakage or wire deformation. For this reason, please do not put excessive stress on LEDs, especially when the LEDs are heated such as during Reflow Soldering. LED 的环氧树脂封装部分相当脆弱, 请勿用坚硬 尖锐的物体刮 擦封装树脂部分 在用镊子夹取的时候也应当小心注意 The epoxy resin of encapsulant is fragile, so please avoid scratch or friction over the epoxy resin surface. While handling the product with tweezers, do not hold by the epoxy resin, be careful. 5. 眼睛保护忠告 : Safety Advice For Human Eyes LED 发光时, 请勿直视发光光源, 特别是对于一些光强较高的 LED, 强光可能伤害你的眼睛 Viewing direct to the light emitting center of the LEDs, especially those of great Luminous Intensity will cause great hazard to human eyes. Please be careful.